- Set up mvebu BAR 0 so MSI works even if bootloader doesn't do this
(Shmuel Hazan)
* remotes/lorenzo/pci/mvebu:
PCI: mvebu: Setup BAR0 in order to fix MSI
- Fix loongson class code quirk so it happens early enough (Tiezhu Yang)
* remotes/lorenzo/pci/loongson:
PCI: loongson: Use DECLARE_PCI_FIXUP_EARLY for bridge_class_quirk()
- Fix hv timing issue that causes kdump failures (Wei Hu)
- Make some hv functions static (Wei Yongjun)
* remotes/lorenzo/pci/hv:
PCI: hv: Make some functions static
PCI: hv: Fix a timing issue which causes kdump to fail occasionally
- Convert cadence to use standard "dma-ranges" DT property instead of its
own "cdns,no-bar-match-nbits" (Kishon Vijay Abraham I)
- Fix pm_runtime_put_sync() issues in cadence error paths (Kishon Vijay
Abraham I)
- Add PTR_ALIGN_DOWN macro (Kishon Vijay Abraham I)
- Convert cadence r/w accessors to only 32-bit accesses (Kishon Vijay
Abraham I)
- Add cadence support to start Link and check Link status (Kishon Vijay
Abraham I)
- Allow custom PCI ops for cadence-based drivers (Kishon Vijay Abraham I)
- Remove "mem" from cadence reg binding since it's not memory and it
overlaps the PCIe config and memory region (Kishon Vijay Abraham I)
- Add cadence ->cpu_addr_fixup() for platforms that require absolute
addresses in the ATU, not just offsets (Kishon Vijay Abraham I)
- Update cadence Vendor IDs using local management registers, not
architected config space (Kishon Vijay Abraham I)
- Add cadence endpoint driver MSI-X support (Kishon Vijay Abraham I)
- Add bindings and driver for TI J721E SoC, supporting both host and
endpoint mode (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/cadence:
MAINTAINERS: Add Kishon Vijay Abraham I for TI J721E SoC PCIe
misc: pci_endpoint_test: Add J721E in pci_device_id table
PCI: j721e: Add TI J721E PCIe driver
dt-bindings: PCI: Add EP mode dt-bindings for TI's J721E SoC
dt-bindings: PCI: Add host mode dt-bindings for TI's J721E SoC
PCI: cadence: Add MSI-X support to Endpoint driver
PCI: cadence: Fix updating Vendor ID and Subsystem Vendor ID register
PCI: cadence: Add new *ops* for CPU addr fixup
dt-bindings: PCI: cadence: Remove "mem" from reg binding
PCI: cadence: Allow pci_host_bridge to have custom pci_ops
PCI: cadence: Add support to start link and verify link status
PCI: cadence: Convert all r/w accessors to perform only 32-bit accesses
linux/kernel.h: Add PTR_ALIGN_DOWN macro
PCI: cadence: Fix cdns_pcie_{host|ep}_setup() error path
PCI: cadence: Use "dma-ranges" instead of "cdns,no-bar-match-nbits" property
- Use pci_channel_state_t instead of enum pci_channel_state (Luc Van
Oostenryck)
- Simplify __aer_print_error() (Bjorn Helgaas)
- Log AER correctable errors as warning, not error (Matt Jolly)
- Rename pci_aer_clear_device_status() to pcie_clear_device_status() (Bjorn
Helgaas)
- Clear PCIe Device Status errors only if OS owns AER (Jonathan Cameron)
* pci/error:
PCI/ERR: Clear PCIe Device Status errors only if OS owns AER
PCI/ERR: Rename pci_aer_clear_device_status() to pcie_clear_device_status()
PCI/AER: Log correctable errors as warning, not error
PCI/AER: Simplify __aer_print_error()
PCI: Use 'pci_channel_state_t' instead of 'enum pci_channel_state'
Add support for PCIe controller in J721E SoC. The controller uses the
Cadence PCIe core programmed by pcie-cadence*.c. The PCIe controller
will work in both host mode and device mode.
Some of the features of the controller are:
*) Supports both RC mode and EP mode
*) Supports MSI and MSI-X support
*) Supports upto GEN3 speed mode
*) Supports SR-IOV capability
*) Ability to route all transactions via SMMU (support will be added
in a later patch).
Link: https://lore.kernel.org/r/20200722110317.4744-14-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fix a number of missing __iomem and __user tags in the ioctl functions of
the switchtec driver. This fixes a number of sparse warnings of the form:
$ make C=2 drivers/pci/switch/
drivers/pci/switch/switchtec.c:... incorrect type in ... (different address spaces)
Fixes: 52eabba5bc ("switchtec: Add IOCTLs to the Switchtec driver")
Link: https://lore.kernel.org/r/20200728192434.18993-1-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The sparse tool report build warnings as follows:
drivers/pci/hotplug/rpadlpar_core.c:355:5: warning: symbol 'dlpar_remove_pci_slot' was not declared. Should it be static?
drivers/pci/hotplug/rpadlpar_core.c:461:12: warning: symbol 'rpadlpar_io_init' was not declared. Should it be static?
drivers/pci/hotplug/rpadlpar_core.c:473:6: warning: symbol 'rpadlpar_io_exit' was not declared. Should it be static?
Those functions are not used outside of this file, so mark them static.
Also mark rpadlpar_io_exit() as __exit.
Link: https://lore.kernel.org/r/20200721151735.41181-1-weiyongjun1@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The acpi_get_table() should be coupled with acpi_put_table() if the mapped
table is not used at runtime to release the table mapping.
In pci_quirk_amd_sb_acs(), IVRS table is just used for checking AMD IOMMU
is supported, not used at runtime, so put the table after using it.
Fixes: 15b100dfd1 ("PCI: Claim ACS support for AMD southbridge devices")
Link: https://lore.kernel.org/r/1595411068-15440-1-git-send-email-guohanjun@huawei.com
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Implement ->set_msix() and ->get_msix() callback functions in order
to configure MSIX capability in the PCIe endpoint controller.
Add cdns_pcie_ep_send_msix_irq() to send MSIX interrupts to Host.
cdns_pcie_ep_send_msix_irq() gets the MSIX table address (virtual
address) from "struct cdns_pcie_epf" that gets initialized in
->set_bar() call back function.
[kishon@ti.com: Re-implement MSIX support in accordance with the
re-designed core MSI-X interfaces]
Link: https://lore.kernel.org/r/20200722110317.4744-11-kishon@ti.com
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
sparse report build warning as follows:
drivers/pci/controller/pci-hyperv.c:941:5: warning:
symbol 'hv_read_config_block' was not declared. Should it be static?
drivers/pci/controller/pci-hyperv.c:1021:5: warning:
symbol 'hv_write_config_block' was not declared. Should it be static?
drivers/pci/controller/pci-hyperv.c:1090:5: warning:
symbol 'hv_register_block_invalidate' was not declared. Should it be static?
Those functions are not used outside of this file, so mark them static.
Link: https://lore.kernel.org/r/20200706135234.80758-1-weiyongjun1@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The XUSB pad controller, which provides access to various USB, PCI and
SATA pads (or PHYs), needs to bring up the PLLs associated with these
pads. In order to properly do so, it needs to control the power supplied
to these PLLs.
Remove the PLL power supplies from the PCIe controller because it does
not need direct access to them. Instead it will only use the configured
pads provided by the XUSB pad controller.
Link: https://lore.kernel.org/r/20200623145528.1658337-1-thierry.reding@gmail.com
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The HiSilicon non-ECAM PCIe has been broken since March 2016 commit
7e57fd1444 ("PCI: designware: Move Root Complex setup code to
dw_pcie_setup_rc()"). The reason is this commit moved the iATU setup code
from dw_pcie_host_init() to dw_pcie_setup_rc(), but the hisi driver never
calls dw_pcie_setup_rc(). The result is the PCI memory space is never
configured and the driver can't work. It's also clear it has an iATU as
the config space accesses use it.
There's also no dts file using either "hisilicon,hip05-pcie" or
"hisilicon,hip06-pcie".
Link: https://lore.kernel.org/r/20200724224204.3249055-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Commit 1b79c52844 ("PCI: cadence: Add host driver for Cadence PCIe
controller") in order to update Vendor ID, directly wrote to
PCI_VENDOR_ID register. However PCI_VENDOR_ID in root port configuration
space is read-only register and writing to it will have no effect.
Use local management register to configure Vendor ID and Subsystem Vendor
ID.
Link: https://lore.kernel.org/r/20200722110317.4744-10-kishon@ti.com
Fixes: 1b79c52844 ("PCI: cadence: Add host driver for Cadence PCIe controller")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cadence driver uses "mem" memory resource to obtain the offset of
configuration space address region, memory space address region and
message space address region. The obtained offset is used to program
the Address Translation Unit (ATU). However certain platforms like TI's
J721E SoC require the absolute address to be programmed in the ATU and
not just the offset. Add new *ops* for CPU addr fixup for the platform
drivers to provide the correct address to be programmed in the ATU.
Link: https://lore.kernel.org/r/20200722110317.4744-9-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Certain platforms like TI's J721E allows only 32-bit configuration
space access. In such cases pci_generic_config_read and
pci_generic_config_write cannot be used. Add support in Cadence core
to let pci_host_bridge have custom pci_ops.
Link: https://lore.kernel.org/r/20200722110317.4744-7-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add cdns_pcie_ops to start link and verify link status. The registers
to start link and to check link status is in Platform specific PCIe
wrapper. Add support for platform specific drivers to add callback
functions for the PCIe Cadence core to start link and verify link status.
Link: https://lore.kernel.org/r/20200722110317.4744-6-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Certain platforms like TI's J721E using Cadence PCIe IP can perform only
32-bit accesses for reading or writing to Cadence registers. Convert all
read and write accesses to 32-bit in Cadence PCIe driver in preparation
for adding PCIe support in TI's J721E SoC.
Also add spin lock to disable interrupts while modifying PCI_STATUS
register while raising legacy interrupt since PCI_STATUS is accessible
by both remote RC and EP and time between read and write should be
minimized.
Link: https://lore.kernel.org/r/20200722110317.4744-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
commit bd22885aa1 ("PCI: cadence: Refactor driver to use as a core
library") while refactoring the Cadence PCIe driver to be used as
library, removed pm_runtime_get_sync() from cdns_pcie_ep_setup()
and cdns_pcie_host_setup() but missed to remove the corresponding
pm_runtime_put_sync() in the error path. Fix it here.
Link: https://lore.kernel.org/r/20200722110317.4744-3-kishon@ti.com
Fixes: bd22885aa1 ("PCI: cadence: Refactor driver to use as a core library")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cadence PCIe core driver (host mode) uses "cdns,no-bar-match-nbits"
property to configure the number of bits passed through from PCIe
address to internal address in Inbound Address Translation register.
This only used the NO MATCH BAR.
However standard PCI dt-binding already defines "dma-ranges" to
describe the address ranges accessible by PCIe controller. Add support
in Cadence PCIe host driver to parse dma-ranges and configure the
inbound regions for BAR0, BAR1 and NO MATCH BAR. Cadence IP specifies
maximum size for BAR0 as 256GB, maximum size for BAR1 as 2 GB.
This adds support to take the next biggest region in "dma-ranges" and
find the smallest BAR that each of the regions fit in and if there is
no BAR big enough to hold the region, split the region to see if it can
be fitted using multiple BARs.
"dma-ranges" of J721E will be
dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>;
Since there is no BAR which can hold 2^48 size, NO_MATCH_BAR will be
used here.
Legacy device tree binding compatibility is maintained by retaining
support for "cdns,no-bar-match-nbits".
Link: https://lore.kernel.org/r/20200722110317.4744-2-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Kdump could fail sometime on Hyper-V guest because the retry in
hv_pci_enter_d0() releases child device structures in hv_pci_bus_exit().
Although there is a second asynchronous device relations message sending
from the host, if this message arrives to the guest after
hv_send_resource_allocated() is called, the retry would fail.
Fix the problem by moving retry to hv_pci_probe() and start the retry
from hv_pci_query_relations() call. This will cause a device relations
message to arrive to the guest synchronously; the guest would then be
able to rebuild the child device structures before calling
hv_send_resource_allocated().
Link: https://lore.kernel.org/r/20200727071731.18516-1-weh@microsoft.com
Fixes: c81992e7f4 ("PCI: hv: Retry PCI bus D0 entry on invalid device state")
Signed-off-by: Wei Hu <weh@microsoft.com>
[lorenzo.pieralisi@arm.com: fixed a comment and commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
pcie_clear_device_status() resets the error bits in the PCIe Device Status
Register (PCI_EXP_DEVSTA).
Previously we did this unconditionally, but on ACPI systems, the _OSC AER
bit negotiates control of the AER capability. Per sec 4.5.1 of the System
Firmware Intermediary _OSC and DPC Updates ECN [1], this bit also covers
other error enable/status bits including the following:
Correctable Error Reporting Enable
Non-Fatal Error Reporting Enable
Fatal Error Reporting Enable
Unsupported Request Reporting Enable
These bits are all in the PCIe Device Control register (the ECN omitted
"Reporting", but I think that's a typo), so by implication the _OSC AER bit
also applies to the error status bits in the PCIe Device Status register:
Correctable Error Detected
Non-Fatal Error Detected
Fatal Error Detected
Unsupported Request Detected
Clear the PCIe Device Status error bits only when the OS controls the AER
capability and related error enable/status bits. If platform firmware
controls the AER capability, firmware is responsible for clearing these
bits.
One call path leading here is:
ghes_do_proc
ghes_handle_aer
aer_recover_queue
schedule_work(&aer_recover_work)
...
aer_recover_work_func
pcie_do_recovery
pcie_clear_device_status
[1] System Firmware Intermediary (SFI) _OSC and DPC Updates ECN, Feb 24,
2020, affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/14076
[bhelgaas: commit log, move test from pcie_clear_device_status() to callers]
Link: https://lore.kernel.org/r/20200622113523.891666-1-Jonathan.Cameron@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_aer_clear_device_status() clears the error bits in the PCIe Device
Status Register (PCI_EXP_DEVSTA). Every PCIe device has this register,
regardless of whether it supports AER.
Rename pci_aer_clear_device_status() to pcie_clear_device_status() to make
clear that it is PCIe-specific but not AER-specific. Move it to
drivers/pci/pci.c, again since it's not AER-specific. No functional change
intended.
Link: https://lore.kernel.org/r/20200717195619.766662-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
