With further testing with an attached Aeonsemi it was discovered that
the pinctrl MDIO function applied the wrong bitmask. The error was
probably caused by the confusing documentation related to these bits.
Inspecting what the bootloader actually configure, the SGMII_MDIO_MODE
is never actually set but instead it's set force enable to the 2 GPIO
(gpio 1-2) for MDC and MDIO pin.
The usage of GPIO might be confusing but this is just to instruct the
SoC to not mess with those 2 PIN and as Benjamin reported it's also an
Errata of 7581. The FORCE_GPIO_EN doesn't set them as GPIO function
(that is configured by a different register) but it's really to actually
""enable"" those lines.
Normally the SoC should autodetect this by HW but it seems AN7581 have
problem with this and require this workaround to force enable the 2 pin.
Applying this configuration permits correct functionality of any
externally attached PHY.
Cc: stable@vger.kernel.org
Fixes: 1c8ace2d07 ("pinctrl: airoha: Add support for EN7581 SoC")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acked-by: Benjamin Larsson <benjamin.larsson@genexis.eu>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In all the MUX value for LED1 GPIO46 there is a Copy-Paste error where
the MUX value is set to LED0_MODE_MASK instead of LED1_MODE_MASK.
This wasn't notice as there were no board that made use of the
secondary PHY LED but looking at the internal Documentation the actual
value should be LED1_MODE_MASK similar to the other GPIO entry.
Fix the wrong value to apply the correct MUX configuration.
Cc: stable@vger.kernel.org
Fixes: 1c8ace2d07 ("pinctrl: airoha: Add support for EN7581 SoC")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When building on ARCH=um (which does not set HAS_IOMEM), kconfig
reports an unmet dependency caused by PINCTRL_STMFX. It selects
MFD_STMFX, which depends on HAS_IOMEM. To stop this warning,
PINCTRL_STMFX should also depend on HAS_IOMEM.
kconfig warning:
WARNING: unmet direct dependencies detected for MFD_STMFX
Depends on [n]: HAS_IOMEM [=n] && I2C [=y] && OF [=y]
Selected by [y]:
- PINCTRL_STMFX [=y] && PINCTRL [=y] && I2C [=y] && OF_GPIO [=y]
Fixes: 1490d9f841 ("pinctrl: Add STMFX GPIO expander Pinctrl/GPIO driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/20250815022721.1650885-1-rdunlap@infradead.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Pull pin control updates from Linus Walleij:
"Nothing stands out, apart from maybe the interesting Eswin EIC7700, a
RISC-V SoC I've never seen before.
Core changes:
- Open code PINCTRL_FUNCTION_DESC() instead of defining a complex
macro only used in one place
- Add pinmux_generic_add_pinfunction() helper and use this in a few
drivers
New drivers:
- Amlogic S7, S7D and S6 pin control support
- Eswin EIC7700 pin control support
- Qualcomm PMIV0104, PM7550 and Milos pin control support
Because of unhelpful numbering schemes, the Qualcomm driver now
needs to start to rely on SoC codenames
- STM32 HDP pin control support
- Mediatek MT8189 pin control support
Improvements:
- Switch remaining pin control drivers over to the new GPIO set
callback that provides a return value
- Support RSVD (reserved) pins in the STM32 driver
- Move many fixed assignments over to pinctrl_desc definitions
- Handle multiple TLMM regions in the Qualcomm driver"
* tag 'pinctrl-v6.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (105 commits)
pinctrl: mediatek: Add pinctrl driver for mt8189
dt-bindings: pinctrl: mediatek: Add support for mt8189
pinctrl: aspeed-g6: Add PCIe RC PERST pin group
pinctrl: ingenic: use pinmux_generic_add_pinfunction()
pinctrl: keembay: use pinmux_generic_add_pinfunction()
pinctrl: mediatek: moore: use pinmux_generic_add_pinfunction()
pinctrl: airoha: use pinmux_generic_add_pinfunction()
pinctrl: equilibrium: use pinmux_generic_add_pinfunction()
pinctrl: provide pinmux_generic_add_pinfunction()
pinctrl: pinmux: open-code PINCTRL_FUNCTION_DESC()
pinctrl: ma35: use new GPIO line value setter callbacks
MAINTAINERS: add Clément Le Goffic as STM32 HDP maintainer
pinctrl: stm32: Introduce HDP driver
dt-bindings: pinctrl: stm32: Introduce HDP
pinctrl: qcom: Add Milos pinctrl driver
dt-bindings: pinctrl: document the Milos Top Level Mode Multiplexer
pinctrl: qcom: spmi: Add PM7550
dt-bindings: pinctrl: qcom,pmic-gpio: Add PM7550 support
pinctrl: qcom: spmi: Add PMIV0104
dt-bindings: pinctrl: qcom,pmic-gpio: Add PMIV0104 support
...
Pull SoC driver updates from Arnd Bergmann:
"Changes are all over the place, but very little sticks out as
noteworthy.
There is a new misc driver for the Raspberry Pi 5's RP1 multifunction
I/O chip, along with hooking it up to the pinctrl and clk frameworks.
The reset controller and memory subsystems have mainly small updates,
but there are two new reset drivers for the K230 and VC1800B SoCs, and
new memory driver support for Tegra264.
The ARM SMCCC and SCMI firmware drivers gain a few more features that
should help them be supported across more environments. Similarly, the
SoC specific firmware on Tegra and Qualcomm get minor enhancements and
chip support.
In the drivers/soc/ directory, the ASPEED LPC snoop driver gets an
overhaul for code robustness, the Tegra and Qualcomm and NXP drivers
grow to support more chips, while the Hisilicon, Mediatek and Renesas
drivers see mostly janitorial fixes"
* tag 'soc-drivers-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (100 commits)
bus: del unnecessary init var
soc: fsl: qe: convert set_multiple() to returning an integer
pinctrl: rp1: use new GPIO line value setter callbacks
soc: hisilicon: kunpeng_hccs: Fix incorrect log information
dt-bindings: soc: qcom: qcom,pmic-glink: document Milos compatible
dt-bindings: soc: qcom,aoss-qmp: document the Milos Always-On Subsystem side channel
dt-bindings: firmware: qcom,scm: document Milos SCM Firmware Interface
soc: qcom: socinfo: Add support to retrieve APPSBL build details
soc: qcom: pmic_glink: fix OF node leak
soc: qcom: spmi-pmic: add more PMIC SUBTYPE IDs
soc: qcom: socinfo: Add PM7550 & PMIV0108 PMICs
soc: qcom: socinfo: Add SoC IDs for SM7635 family
dt-bindings: arm: qcom,ids: Add SoC IDs for SM7635 family
firmware: qcom: scm: request the waitqueue irq *after* initializing SCM
firmware: qcom: scm: initialize tzmem before marking SCM as available
firmware: qcom: scm: take struct device as argument in SHM bridge enable
firmware: qcom: scm: remove unused arguments from SHM bridge routines
soc: qcom: rpmh-rsc: Add RSC version 4 support
memory: tegra: Add Tegra264 MC and EMC support
firmware: tegra: bpmp: Fix build failure for tegra264-only config
...
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrea della Porta <andrea.porta@suse.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom SoCs drivers updates for 6.17,
please pull the following:
- Andrea adds the RP1 clock, pinctrl/pinconf/gpio and misc driver to
bind them all
* tag 'arm-soc/for-6.17/drivers' of https://github.com/Broadcom/stblinux:
pinctrl: rp1: Implement RaspberryPi RP1 pinmux/pinconf support
misc: rp1: RaspberryPi RP1 misc driver
pinctrl: rp1: Implement RaspberryPi RP1 gpio support
clk: rp1: Add support for clocks provided by RP1
dt-bindings: clock: Add RaspberryPi RP1 clock bindings
Link: https://lore.kernel.org/r/20250630190216.1518354-4-florian.fainelli@broadcom.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Samsung pinctrl drivers changes for v6.17
Add support for programming wake up for Google GS101 SoC pin
controllers, so the SoC can be properly woken up from low power states.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
intel-pinctrl for v6.16-1
* Use new GPIO line value setter callbacks (Bartosz Golaszewski)
* Add missed export.h to the main driver
The following is an automated git shortlog grouped by driver:
baytrail:
- use new GPIO line value setter callbacks
cherryview:
- use new GPIO line value setter callbacks
intel:
- fix build warnings about export.h
- use new GPIO line value setter callbacks
lynxpoint:
- use new GPIO line value setter callbacks
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Merge series from Luca Weiss <luca.weiss@fairphone.com>:
Document and add support for the regulators on PM7550 and PMR735B, which
can be paired with the Milos SoC.
commit 5a3e85c3c3 ("pinmux: Use sequential access to access
desc->pinmux data") tried to address the issue when two client of the
same gpio calls pinctrl_select_state() for the same functionality, was
resulting in NULL pointer issue while accessing desc->mux_owner.
However, issue was not completely fixed due to the way it was handled
and it can still result in the same NULL pointer.
The issue occurs due to the following interleaving:
cpu0 (process A) cpu1 (process B)
pin_request() { pin_free() {
mutex_lock()
desc->mux_usecount--; //becomes 0
..
mutex_unlock()
mutex_lock(desc->mux)
desc->mux_usecount++; // becomes 1
desc->mux_owner = owner;
mutex_unlock(desc->mux)
mutex_lock(desc->mux)
desc->mux_owner = NULL;
mutex_unlock(desc->mux)
This sequence leads to a state where the pin appears to be in use
(`mux_usecount == 1`) but has no owner (`mux_owner == NULL`), which can
cause NULL pointer on next pin_request on the same pin.
Ensure that updates to mux_usecount and mux_owner are performed
atomically under the same lock. Only clear mux_owner when mux_usecount
reaches zero and no new owner has been assigned.
Fixes: 5a3e85c3c3 ("pinmux: Use sequential access to access desc->pinmux data")
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Link: https://lore.kernel.org/20250708-pinmux-race-fix-v2-1-8ae9e8a0d1a1@oss.qualcomm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: renesas: Updates for v6.17
- Use the new GPIO line value setter callbacks,
- Validate pins before setting a mux function on RZ/G2L.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for selecting multiple TLMM regions using the
tlmm-test tool.
The current implementation only selects the TLMM Node region
0, which can lead to incorrect region selection.
QCS 615 TLMM Node dts reg:
tlmm: pinctrl@3100000 {
compatible = "qcom,qcs615-tlmm";
reg = <0x0 0x03100000 0x0 0x300000>,
<0x0 0x03500000 0x0 0x300000>,
<0x0 0x03d00000 0x0 0x300000>;
reg-names = "east",
"west",
"south";
QCS615 gpio57 is in the south region with an offset of 0x39000,
and its address is 0x3d39000. However, the default region selection
is region 0 (east region), resulting in a wrong calculated address
of 0x3139000.
Add a tlmm option parameter named tlmm_reg_name to select the region.
If the user does not input the parameter, the default region is 0.
Signed-off-by: Yuanjie Yang <quic_yuanjiey@quicinc.com>
Link: https://lore.kernel.org/20250624090600.91063-1-quic_yuanjiey@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gs101 differs to other currently supported SoCs in that it has 3 wakeup
mask registers for the 67 external wakeup interrupt pins in alive and
far_alive.
EINT_WAKEUP_MASK 0x3A80 EINT[31:0]
EINT_WAKEUP_MASK2 0x3A84 EINT[63:32]
EINT_WAKEUP_MASK3 0x3A88 EINT[66:64]
Add gs101 specific callbacks and a dedicated gs101_wkup_irq_chip struct to
handle these differences.
The current wakeup mask with upstream is programmed as
WAKEUP_MASK0[0x3A80] value[0xFFFFFFFF]
WAKEUP_MASK1[0x3A84] value[0xF2FFEFFF]
WAKEUP_MASK2[0x3A88] value[0xFFFFFFFF]
Which corresponds to the following wakeup sources:
gpa7-3 vol down
gpa8-1 vol up
gpa10-1 power
gpa8-2 typec-int
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250619-gs101-eint-mask-v1-2-89438cfd7499@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Sparse complains:
sparse warnings: (new ones prefixed by >>)
>> drivers/pinctrl/meson/pinctrl-amlogic-a4.c:126:24: sparse: sparse:
symbol 'multi_mux_s7' was not declared. Should it be static?
>> drivers/pinctrl/meson/pinctrl-amlogic-a4.c:135:28: sparse: sparse:
symbol 's7_priv_data' was not declared. Should it be static?
>> drivers/pinctrl/meson/pinctrl-amlogic-a4.c:140:24: sparse: sparse:
symbol 'multi_mux_s6' was not declared. Should it be static?
>> drivers/pinctrl/meson/pinctrl-amlogic-a4.c:154:28: sparse: sparse:
symbol 's6_priv_data' was not declared. Should it be static?
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202506122145.wWAtKBoy-lkp@intel.com/
Cc: Xianwei Zhao <xianwei.zhao@amlogic.com>
Fixes: 1f8e5dfdda ("pinctrl: meson: support amlogic S6/S7/S7D SoC")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/20250624-amlogic-a4-fix-v1-1-03f0856d10cb@linaro.org
Add a NULL check for the return value of of_get_property() when
retrieving the "pinmux" property in the group parser. This avoids
a potential NULL pointer dereference if the property is missing
from the device tree node.
Also fix a typo ("sintenel") in the device ID match table comment,
correcting it to "sentinel".
Fixes: 545887eab6 ("pinctrl: canaan: Add support for k230 SoC")
Reported-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Ze Huang <huangze@whut.edu.cn>
Link: https://lore.kernel.org/20250624-k230-return-check-v1-1-6b4fc5ba0c41@whut.edu.cn
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The zynq driver can be enabled for compile-testing on builds without
CONFIG_OF, leading to a link error:
ld.lld-21: error: undefined symbol: pinconf_generic_dt_node_to_map
referenced by pinconf-generic.h:231 (/home/arnd/arm-soc/include/linux/pinctrl/pinconf-generic.h:231)
drivers/pinctrl/pinctrl-zynq.o:(pinconf_generic_dt_node_to_map_all) in archive vmlinux.a
Prevent this with the proper compile time dependency.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202506212021.deAhuaWr-lkp@intel.com/
Fixes: 1982621dec ("pinctrl: Allow compile testing for K210, TB10X and ZYNQ")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/20250620130814.2580678-1-arnd@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
