In order that the LED trigger can blink the switch MAC ports LED, it
needs to know the netdev associated to the port. Add the callback to
return the struct device of the netdev.
Add an helper function qca8k_phy_to_port() to convert the phy back to
dsa_port index, as we reference LED port based on the internal PHY
index and needs to be converted back.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement hw_control ops to drive Switch LEDs based on hardware events.
Netdev trigger is the declared supported trigger for hw control
operation and supports the following mode:
- tx
- rx
When hw_control_set is called, LEDs are set to follow the requested
mode.
Each LEDs will blink at 4Hz by default.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E6361 is an 8-port switch derived from the
88E6393X/88E9193X/88E6191X switches family. It can benefit from the
existing mv88e6xxx driver by simply adding the proper switch description in
the driver. Main differences with other switches from this
family are:
- 8 ports exposed (instead of 11): ports 1, 2 and 8 not available
- No 5GBase-x nor SFI/USXGMII support
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some switches families have minor differences on supported link speed for
ports. Instead of redefining a new port_max_speed_mode for each different
configuration, allow to pass mv88e6xxx_chip structure to allow
differentiating those chips by known chip id
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
88E6393X/88E6193X/88E6191X switches have in fact 8 internal PHYs, but those
are not present starting at port 0: supported ports go from 1 to 8
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mv88e6xxx currently assumes that switch equipped with internal phys have
those phys mapped contiguously starting from port 0 (see
mv88e6xxx_phy_is_internal). However, some switches have internal PHYs but
NOT starting from port 0. For example 88e6393X, 88E6193X and 88E6191X have
integrated PHYs available on ports 1 to 8
To properly support this offset, add a new field to allow specifying an
internal PHYs layout. If field is not set, default layout is assumed (start
at port 0)
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure to use existing helper to get internal PHYs count instead of
redoing it manually
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since this function is a simple helper, we do not need to pass a full
dsa_switch structure, we can directly pass the mv88e6xxx_chip structure.
Doing so will allow to share this function with any other function
not manipulating dsa_switch structure but needing info about number of
internal phys
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no gpiod_export() and gpiod_unexport() looks pretty much stray.
The gpiod_export() and gpiod_unexport() shouldn't be used in the code,
GPIO sysfs is deprecated. That said, simply drop the stray call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230528142531.38602-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This update introduces specific register access boundaries for the
KSZ8873 and KSZ8863 chips within the DSA Microchip driver. The outlined
ranges target global control registers, port registers, and advanced
control registers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch prepares the ksz8863_smi part of ksz8 driver to utilize the
regmap register access validation feature.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The only place where this variable would be set to false is the
ksz8_config_cpu_port() function. But it is done in a bogus way:
for (i = 0; i < dev->phy_port_cnt; i++) {
if (i == dev->phy_port_cnt) <--- will be never executed.
break;
p->on = 1;
So, we never have a situation where p->on = 0. In this case, we can just
remove it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It is not immediately obvious that this driver allocates, via the
KSZ_REGMAP_TABLE() macro, 3 regmaps for register access: dev->regmap[0]
for 8-bit access, dev->regmap[1] for 16-bit and dev->regmap[2] for
32-bit access.
In future changes that add support for reg_fields, each field will have
to specify through which of the 3 regmaps it's going to go. Add an enum
now, to denote one of the 3 register access widths, and make the code go
through some wrapper functions for easier review and further
modification.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch refines the error handling mechanism for 8-bit register
read-modify-write operations. In case of a failure, it now logs an error
message detailing the problematic offset. This enhancement aids in
debugging by providing more precise information when these operations
encounter issues.
Furthermore, the ksz_prmw8() function has been updated to return error
values rather than void, enabling calling functions to appropriately
respond to errors.
Additionally, in case of an error that affects both the current and
future accesses, the PHY driver will log the errors consistently, akin
to the existing behavior in all ksz_read*/ksz_write* helpers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use the newly introduced lynx_pcs_create_mdiodev() which simplifies the
creation and destruction of the lynx PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the link forcing out of mac_config() and into the mac_prepare()
and mac_finish() methods. This results in no change to the order in
which these operations are performed, but does mean when we convert
mv88e6xxx to phylink_pcs support, we will continue to preserve this
ordering.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to datasheet, the command opcode must be specified
into bits [14:12] of the Extended Port Control register (EPC).
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marco Migliore <m.migliore@tiesse.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ports are in standalone mode, they should have learning disabled to
avoid adding new entries in the MAC lookup table which might be used by
other bridge ports to forward packets. While adding that, also make sure
learning is enabled for CPU port.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stp_set_state() should actually allow receiving BPDU while in LEARNING
mode which is not the case. Additionally, the BLOCKEN bit does not
actually forbid sending forwarded frames from that port. To fix this, add
a5psw_port_tx_enable() function which allows to disable TX. However, while
its name suggest that TX is totally disabled, it is not and can still
allow to send BPDUs even if disabled. This can be done by using forced
forwarding with the switch tagging mechanism but keeping "filtering"
disabled (which is already the case in the rzn1-a5sw tag driver). With
these fixes, STP support is now functional.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, management frame were discarded before reaching the CPU port due
to a misconfiguration of the MGMT_CONFIG register. Enable them by setting
the correct value in this register in order to correctly receive management
frame and handle STP.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On mt753x_cpu_port_enable() there's code that enables flooding for the CPU
port only. Since mt753x_cpu_port_enable() runs twice when both CPU ports
are enabled, port 6 becomes the only port to forward the frames to. But
port 5 is the active port, so no frames received from the user ports will
be forwarded to port 5 which breaks network connectivity.
Every bit of the BC_FFP, UNM_FFP, and UNU_FFP bits represents a port. Fix
this issue by setting the bit that corresponds to the CPU port without
overwriting the other bits.
Clear the bits beforehand only for the MT7531 switch. According to the
documents MT7621 Giga Switch Programming Guide v0.3 and MT7531 Reference
Manual for Development Board v1.0, after reset, the BC_FFP, UNM_FFP, and
UNU_FFP bits are set to 1 for MT7531, 0 for MT7530.
The commit 5e5502e012 ("net: dsa: mt7530: fix roaming from DSA user
ports") silently changed the method to set the bits on the MT7530_MFC.
Instead of clearing the relevant bits before mt7530_cpu_port_enable()
which runs under a for loop, the commit started doing it on
mt7530_cpu_port_enable().
Back then, this didn't really matter as only a single CPU port could be
used since the CPU port number was hardcoded. The driver was later changed
with commit 1f9a6abecf ("net: dsa: mt7530: get cpu-port via dp->cpu_dp
instead of constant") to retrieve the CPU port via dp->cpu_dp. With that,
this silent change became an issue for when using multiple CPU ports.
Fixes: 5e5502e012 ("net: dsa: mt7530: fix roaming from DSA user ports")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multi-chip module MT7530 switch with a 40 MHz oscillator on the
MT7621AT, MT7621DAT, and MT7621ST SoCs forwards corrupt frames using
trgmii.
This is caused by the assumption that MT7621 SoCs have got 150 MHz PLL,
hence using the ncpo1 value, 0x0780.
My testing shows this value works on Unielec U7621-06, Bartel's testing
shows it won't work on Hi-Link HLK-MT7621A and Netgear WAC104. All devices
tested have got 40 MHz oscillators.
Using the value for 125 MHz PLL, 0x0640, works on all boards at hand. The
definitions for 125 MHz PLL exist on the Banana Pi BPI-R2 BSP source code
whilst 150 MHz PLL don't.
Forwarding frames using trgmii on the MCM MT7530 switch with a 25 MHz
oscillator on the said MT7621 SoCs works fine because the ncpo1 value
defined for it is for 125 MHz PLL.
Change the 150 MHz PLL comment to 125 MHz PLL, and use the 125 MHz PLL
ncpo1 values for both oscillator frequencies.
Link: 81d24bbce7/u-boot-mt/drivers/net/rt2880_eth.c (L2195)
Fixes: 7ef6f6f8d2 ("net: dsa: mt7530: Add MT7621 TRGMII mode support")
Tested-by: Bartel Eerdekens <bartel.eerdekens@constell8.be>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rsvd2cpu capability for mv88e6321 model, to allow proper bpdu
processing.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Fixes: 51c901a775 ("net: dsa: mv88e6xxx: distinguish Global 2 Rsvd2CPU")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With LEDS_CLASS=m, a built-in qca8k driver fails to link:
arm-linux-gnueabi-ld: drivers/net/dsa/qca/qca8k-leds.o: in function `qca8k_setup_led_ctrl':
qca8k-leds.c:(.text+0x1ea): undefined reference to `devm_led_classdev_register_ext'
Change the dependency to avoid the broken configuration.
Fixes: 1e264f9d29 ("net: dsa: qca8k: add LEDs basic support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230420213639.2243388-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are two variants of the MT7531 switch IC which got different
features (and pins) regarding port 5:
* MT7531AE: SGMII/1000Base-X/2500Base-X SerDes PCS
* MT7531BE: RGMII
Moving the creation of the SerDes PCS from mt753x_setup to mt7530_probe
with commit 6de2852297 ("net: dsa: mt7530: move SGMII PCS creation
to mt7530_probe function") works fine for MT7531AE which got two
instances of mtk-pcs-lynxi, however, MT7531BE requires mt7531_pll_setup
to setup clocks before the single PCS on port 6 (usually used as CPU
port) starts to work and hence the PCS creation failed on MT7531BE.
Fix this by introducing a pointer to mt7531_create_sgmii function in
struct mt7530_priv and call it again at the end of mt753x_setup like it
was before commit 6de2852297 ("net: dsa: mt7530: move SGMII PCS
creation to mt7530_probe function").
Fixes: 6de2852297 ("net: dsa: mt7530: move SGMII PCS creation to mt7530_probe function")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/ZDvlLhhqheobUvOK@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because of the logic in place, SW_HUGE_PACKET can never be set.
(If the first condition is true, then the 2nd one is also true, but is not
executed)
Change the logic and update each bit individually.
Fixes: 29d1e85f45 ("net: dsa: microchip: ksz8: add MTU configuration support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/43107d9e8b5b8b05f0cbd4e1f47a2bb88c8747b2.1681755535.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add LEDs blink_set() support to qca8k Switch Family.
These LEDs support hw accellerated blinking at a fixed rate
of 4Hz.
Reject any other value since not supported by the LEDs switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LEDs basic support for qca8k Switch Family by adding basic
brightness_set() support.
Since these LEDs refelect port status, the default label is set to
":port". DT binding should describe the color and function of the
LEDs using standard LEDs api.
Each LED always have the device name as prefix. The device name is
composed from the mii bus id and the PHY addr resulting in example
names like:
- qca8k-0.0:00:amber:lan
- qca8k-0.0:00:white:lan
- qca8k-0.0:01:amber:lan
- qca8k-0.0:01:white:lan
These LEDs supports only blocking variant of the brightness_set()
function since they can sleep during access of the switch leds to set
the brightness.
While at it add to the qca8k header file each mode defined by the Switch
Documentation for future use.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move qca8k_port_to_phy() to qca8k header as it's useful for future
reference in Switch LEDs module since the same logic is applied to get
the right index of the switch port.
Make it inline as it's simple function that just decrease the port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to not transmit (preemptible) frames which will be received by
the link partner as corrupted (because it doesn't support FP), the
hardware requires the driver to program the QSYS_PREEMPTION_CFG_P_QUEUES
register only after the MAC Merge layer becomes active (verification
succeeds, or was disabled).
There are some cases when FP is known (through experimentation) to be
broken. Give priority to FP over cut-through switching, and disable FP
for known broken link modes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mqprio queue configuration can appear either through
TC_SETUP_QDISC_MQPRIO or through TC_SETUP_QDISC_TAPRIO. Make sure both
are treated in the same way.
Code does nothing new for now (except for rejecting multiple TXQs per
TC, which is a useless concept with DSA switches).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This doesn't apply anything to hardware and in general doesn't do
anything that the software variant doesn't do, except for checking that
there isn't more than 1 TXQ per TC (TXQs for a DSA switch are a dubious
concept anyway). The reason we add this is to be able to parse one more
field added to struct tc_mqprio_qopt_offload, namely preemptible_tcs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the switch emits an IRQ, we don't know what caused it, and we
iterate through all ports to check the MAC Merge status.
Move that iteration inside the ocelot lib; we will change the locking in
a future change and it would be good to encapsulate that lock completely
within the ocelot lib.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
That comment was written prior to knowing that what I was actually
seeing was a manifestation of the bug fixed in commit b4024c9e5c
("felix: Fix initialization of ioremap resources").
There isn't any particular reason now why the hardware initialization is
done in felix_setup(), so just delete that comment to avoid spreading
misinformation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch can either take the MAC or the PHY role in an MII or RMII
link. There are distinct PHY_INTERFACE_ macros for these two roles.
Correct the mapping so that the `REV` version is used for the PHY
role.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230411023541.2372609-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To handle potential read/write operation failures, update
ksz8_w_sta_mac_table() to make use of the return values provided by
read/write functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since ksz8_w_sta_mac_table() is only used within ksz8795.c, make it static
to limit its scope.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Take advantage of the return values provided by read/write functions in
ksz8_r_sta_mac_table() to handle cases where read/write operations may
fail.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Prepare for the next patch by ensuring that ksz8_r_sta_mac_table() does
not use error codes for empty entries. This change will enable better
handling of read/write errors in the upcoming patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As ksz8_r_sta_mac_table() is only used within ksz8795.c, there is no need
to export it. Make the function static for better encapsulation.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for add/del_fdb operations and utilize the refactored static
MAC table code. This resolves kernel warnings caused by the lack of fdb
add function support in the current driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Move static MAC table operations to separate functions in order to reuse
the code for add/del_fdb. This is needed to address kernel warnings
caused by the lack of fdb add function support in the current driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add driver for the built-in Gigabit Ethernet switch which can be found
in the MediaTek MT7988 SoC.
The switch shares most of its design with MT7530 and MT7531, but has
it's registers mapped into the SoCs register space rather than being
connected externally or internally via MDIO.
Introduce a new platform driver to support that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As MT7530 and MT7531 internally use 32-bit wide registers, each access
to any register of the switch requires several operations on the MDIO
bus. Hence if there is congruent access, e.g. due to PCS or PHY
polling, this can mess up and interfere with another ongoing register
access sequence.
However, the MDIO bus mutex is only relevant for MDIO-connected
switches. Prepare switches which have there registers directly mapped
into the SoCs register space via MMIO which do not require such
locking. There we can simply use regmap's default locking mechanism.
Hence guard mutex operations to only be performed in case of MDIO
connected switches.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split MT7530 switch driver into a common part and a part specific
for MDIO connected switches and multi-chip modules.
Move MDIO-specific functions to newly introduced mt7530-mdio.c while
keeping the common parts in mt7530.c.
Introduce new Kconfig symbol CONFIG_NET_DSA_MT7530_MDIO which is
implied by CONFIG_NET_DSA_MT7530.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
MT7988 shares a significant part of the setup function with MT7531.
Split-off those parts into a shared function which is going to be used
also by mt7988_setup.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move commonly used parts from mt7530_remove into new
mt7530_remove_common helper function which will be used by both,
mt7530_remove and the to-be-introduced mt7988_remove.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move commonly used parts from mt7530_probe into new mt7530_probe_common
helper function which will be used by both, mt7530_probe and the
to-be-introduced mt7988_probe.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of splitting mt7530.c into a driver for MDIO-connected
as well as MDIO-accessed built-in switches on one hand and MMIO-accessed
built-in switches move the p5_inft_modes() function from mt7530.h to
mt7530.c. The function is only needed there and will trigger a compiler
warning about a defined but unused function otherwise when including
mt7530.h in the to-be-introduced bus-specific drivers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the MDIO bus lock only needs to be involved if actually operating
on an MDIO-connected switch we will need to skip locking for built-in
switches which are accessed via MMIO.
Create helper functions which simplify that upcoming change.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move creating the SGMII PCS from mt753x_setup() to the more appropriate
mt7530_probe() function.
This is done also in preparation of moving all functions related to
MDIO-connected MT753x switches to a separate module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use regmap API to access the switch register space.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of wrapping the locked register accessor functions, use the
unlocked variants and add locking wrapper functions to let regmap
handle the locking.
This is a preparation towards being able to always use regmap to
access switch registers instead of open-coded accessor functions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of macro templates use a dedidated function and allocated
regmap_config when creating the regmaps for the pcs-mtk-lynxi
instances.
This is in preparation to switching to use unlocked regmap accessors
and have regmap's locking API handle locking for us.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simply returning the negative error value instead of the read value
doesn't seem like a good idea. Return 0 instead and add WARN_ON_ONCE(1)
so this kind of error will not go unnoticed.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The force watchdog event bit is not cleared during SW reset in the
mv88e6393x switch. This is a different behavior compared to mv886390 which
clears the force WD event bit as advertised. This causes a force WD event
to be handled over and over again as the SW reset following the event never
clears the force WD event bit.
Explicitly clear the watchdog event register to 0 in irq_action when
handling an event to prevent the switch from sending continuous interrupts.
Marvell aren't aware of any other stuck bits apart from the force WD
bit.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family"
Signed-off-by: Gustav Ekelund <gustaek@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Do not set the MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP bit on CPU or DSA ports.
This allows the host CPU port to be a regular IGMP listener by sending out
IGMP Membership Reports, which would otherwise not be forwarded by the
mv88exxx chip, but directly looped back to the CPU port itself.
Fixes: 54d792f257 ("net: dsa: Centralise global and port setup code into mv88e6xxx.")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230329150140.701559-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement phy_read16() and phy_write16() ops for B53 MMAP to avoid accessing
B53_PORT_MII_PAGE registers which hangs the device.
This access should be done through the MDIO Mux bus controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the BCM53134 Ethernet switch in the existing b53 dsa driver.
BCM53134 is very similar to the BCM58XX series.
Signed-off-by: Paul Geurts <paul.geurts@prodrive-technologies.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FID is directly mapped to VID. However, configuring a MAC address with a
VID != 0 resulted in incorrect configuration due to an incorrect bit
mask. This kernel commit fixed the issue by correcting the bit mask and
ensuring proper configuration of MAC addresses with non-zero VID.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current regmap bulk access is broken, resulting to wrong reads/writes
if ksz_read64/ksz_write64 functions are used.
Mostly this issue was visible by using ksz8_fdb_dump(), which returned
corrupt MAC address.
The reason is that regmap was configured to have max_raw_read/write,
even if ksz8863_mdio_read/write functions are able to handle unlimited
read/write accesses. On ksz_read64 function we are using multiple 32bit
accesses by incrementing each access by 1 instead of 4. Resulting buffer
had 01234567.12345678 instead of 01234567.89abcdef.
We have multiple ways to fix it:
- enable 4 byte alignment for 32bit accesses. Since the HW do not have
this requirement. It will break driver.
- disable max_raw_* limit.
This patch is removing max_raw_* limit for regmap accesses in ksz8863_smi.
Fixes: 60a3647600 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the dynamic MAC table is empty, we will still extract one outdated
entry. Fix it by using correct bit offset.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are using wrong offset, so we will get not a timestamp.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current ksz8_fdb_dump() is able to extract only max 249 entries on
the ksz8863/ksz8873 series of switches. This happened due to wrong
bit mask and offset calculation.
This commit corrects the issue and allows for the complete extraction of
all 1024 entries.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch, the ksz8_fdb_dump() function had several issues, such
as uninitialized variables and incorrect usage of source port as a bit
mask. These problems caused inaccurate reporting of vid information and
port assignment in the bridge fdb.
Fixes: e587be759e ("net: dsa: microchip: update fdb add/del/dump in ksz_common")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The probe function sets priv->chip_data to (void *)priv + sizeof(*priv)
with the expectation that priv has enough trailing space.
However, only realtek-smi actually allocated this chip_data space.
Do likewise in realtek-mdio to fix out-of-bounds accesses.
These accesses likely went unnoticed so far, because of an (unused)
buf[4096] member in struct realtek_priv, which caused kmalloc to
round up the allocated buffer to a big enough size, so nothing of
value was overwritten. With a different allocator (like in the barebox
bootloader port of the driver) or with KASAN, the memory corruption
becomes quickly apparent.
Fixes: aac9400106 ("net: dsa: realtek: add new mdio interface for drivers")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20230323103735.2331786-1-a.fatoum@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move setting the ssc_delta variable to under the PHY_INTERFACE_MODE_TRGMII
case as it's only needed when trgmii is used.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230320190520.124513-3-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move lowering the TRGMII Tx clock driving to mt7530_setup(), after setting
the core clock, as seen on the U-Boot MediaTek ethernet driver.
Move the code which looks like it lowers the TRGMII Rx clock driving to
after the TRGMII Tx clock driving is lowered. This is run after lowering
the Tx clock driving on the U-Boot MediaTek ethernet driver as well.
This way, the switch should consume less power regardless of port 6 being
used.
Update the comment explaining mt7530_pad_clk_setup().
Tested rgmii and trgmii modes of port 6 and rgmii mode of port 5 on MCM
MT7530 on MT7621AT Unielec U7621-06 and standalone MT7530 on MT7623NI
Bananapi BPI-R2.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Link: 29a48bf9cc/drivers/net/mtk_eth.c (L682)
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230320190520.124513-2-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Split the code that enables and disables TRGMII clocks and core clock.
Move enabling and disabling core clock to mt7530_pll_setup() as it's
supposed to be run there.
Add 20 ms delay before enabling the core clock as seen on the U-Boot
MediaTek ethernet driver.
Change the comment for enabling and disabling TRGMII clocks as the code
seems to affect both TXC and RXC.
Tested rgmii and trgmii modes of port 6 and rgmii mode of port 5 on MCM
MT7530 on MT7621AT Unielec U7621-06 and standalone MT7530 on MT7623NI
Bananapi BPI-R2.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Link: 29a48bf9cc/drivers/net/mtk_eth.c (L589)
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230320190520.124513-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM6318 and BCM63268 SoCs require a special handling for their RGMIIs, so we
should be able to identify them as a special BCM63xx switch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM6318, BCM6362 and BCM63268 are SoCs with a B53 MMAP switch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM63xx RGMII ports require additional configuration in order to work.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230319220805.124024-1-noltari@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
pcs_get_state() implementations are not supposed to alter an_enabled.
Remove this assignment.
Fixes: b3591c2a36 ("net: dsa: qca8k: Switch to PHYLINK instead of PHYLIB")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1pdsE5-00Dl2l-8F@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit 2c7e46edbd ("net: dsa: mv88e6xxx: mask apparently non-existing
phys during probing") added non-trivial bus->phy_mask in
mv88e6xxx_mdio_register() in order to avoid excessive mdio bus
transactions during probing.
But the mask is incorrect for switches with non-zero phy_base_addr (such
as 88E6341).
Fix this.
Fixes: 2c7e46edbd ("net: dsa: mv88e6xxx: mask apparently non-existing phys during probing")
Signed-off-by: Marek Behún <kabel@kernel.org>
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230319140238.9470-1-kabel@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Implement regmap access wrappers, for now only to be used by the
pcs-mtk-lynxi driver.
Make use of this external PCS driver and drop the now reduntant
implementation in mt7530.c.
As a nice side effect the SGMII registers can now also more easily be
inspected for debugging via /sys/kernel/debug/regmap.
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VSC7512 has four ports with internal phys that are already supported.
There are additional ports that can be configured to work with external
phys.
Add support for these additional ethernet ports.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ports for Ocelot devices (VSC7511, VSC7512, VSC7513 and VSC7514) support
external phys. When external phys are used, additional configuration on
each port is required to enable QSGMII mode and set external phy modes.
Add a configurable hook into these routines, so the external ports can be
used.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a user of the Felix driver has a port running in SGMII / QSGMII mode, it
will need to utilize phylink_mac_config(). Add this configurability.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC7512 and VSC7514 have internal PLLs that can be used to control
different peripherals. Initialize these high speed I/O (HSIO) PLLs when
they exist, so that dependent peripherals like QSGMII can function.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid excessive mdio bus transactions during probing, mask all phy
addresses that do not exist (there is a 1:1 mapping between switch port
number and phy address).
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Call the rather expensive mv88e6xxx_mdios_register() at the beginning of
mv88e6xxx_setup(). This avoids the double call via mv88e6xxx_probe()
during boot.
For symmetry, call mv88e6xxx_mdios_unregister() at the end of
mv88e6xxx_teardown().
Link: https://lore.kernel.org/lkml/449bde236c08d5ab5e54abd73b645d8b29955894.camel@gmail.com/
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move mv88e6xxx_setup() below mv88e6xxx_mdios_register(), so that we are
able to call the latter one from here. Do the same thing for the
inverse functions.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
irq_find_mapping() does not need irq_dispose_mapping(), only
irq_create_mapping() does.
Calling irq_dispose_mapping() from mv88e6xxx_g2_irq_mdio_free() and from
the error path of mv88e6xxx_g2_irq_mdio_setup() effectively means that
the mdiobus logic (for internal PHY interrupts) is disposing of a
hwirq->virq mapping which it is not responsible of (but instead, the
function pair mv88e6xxx_g2_irq_setup() + mv88e6xxx_g2_irq_free() is).
With the current code structure, this isn't such a huge problem, because
mv88e6xxx_g2_irq_mdio_free() is called relatively close to the real
owner of the IRQ mappings:
mv88e6xxx_remove()
-> mv88e6xxx_unregister_switch()
-> mv88e6xxx_mdios_unregister()
-> mv88e6xxx_g2_irq_mdio_free()
-> mv88e6xxx_g2_irq_free()
and the switch isn't 'live' in any way such that it would be able of
generating interrupts at this point (mv88e6xxx_unregister_switch() has
been called).
However, there is a desire to split mv88e6xxx_mdios_unregister() and
mv88e6xxx_g2_irq_free() such that mv88e6xxx_mdios_unregister() only gets
called from mv88e6xxx_teardown(). This is much more problematic, as can
be seen below.
In a cross-chip scenario (say 3 switches d0032004.mdio-mii:10,
d0032004.mdio-mii:11 and d0032004.mdio-mii:12 which form a single DSA
tree), it is possible to unbind the device driver from a single switch
(say d0032004.mdio-mii:10).
When that happens, mv88e6xxx_remove() will be called for just that one
switch, and this will call mv88e6xxx_unregister_switch() which will tear
down the entire tree (calling mv88e6xxx_teardown() for all 3 switches).
Assuming mv88e6xxx_mdios_unregister() was moved to mv88e6xxx_teardown(),
at this stage, all 3 switches will have called irq_dispose_mapping() on
their mdiobus virqs.
When we bind again the device driver to d0032004.mdio-mii:10,
mv88e6xxx_probe() is called for it, which calls dsa_register_switch().
The DSA tree is now complete again, and mv88e6xxx_setup() is called for
all 3 switches.
Also assuming that mv88e6xxx_mdios_register() is moved to
mv88e6xxx_setup() (the 2 assumptions go together), at this point,
d0032004.mdio-mii:11 and d0032004.mdio-mii:12 don't have an IRQ mapping
for the internal PHYs anymore, as they've disposed of it in
mv88e6xxx_teardown(). Whereas switch d0032004.mdio-mii:10 has re-created
it, because its code path comes from mv88e6xxx_probe().
Simply put, this change prepares the driver to handle the movement of
mv88e6xxx_mdios_register() to mv88e6xxx_setup() for cross-chip DSA trees.
Also, the code being deleted was partially wrong anyway (in a way which
may have hidden this other issue). mv88e6xxx_g2_irq_mdio_setup()
populates bus->irq[] starting with offset chip->info->phy_base_addr, but
the teardown path doesn't apply that offset too. So it disposes of virq
0 for phy = [ 0, phy_base_addr ).
All switch families have phy_base_addr = 0, except for MV88E6141 and
MV88E6341 which have it as 0x10. I guess those families would have
happened to work by mistake in cross-chip scenarios too.
I'm deleting the body of mv88e6xxx_g2_irq_mdio_free() but leaving its
call sites and prototype in place. This is because, if we ever need to
add back some teardown procedure in the future, it will be perhaps
error-prone to deduce the proper call sites again. Whereas like this,
no extra code should get generated, it shouldn't bother anybody.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CPU port should also be enabled in order to get a working switch.
Fixes: a5538a777b ("net: dsa: b53: mmap: Add device tree support")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230316172807.460146-1-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rtl8365mb was using a fixed MTU size of 1536, which was probably
inspired by the rtl8366rb's initial frame size. However, unlike that
family, the rtl8365mb family can specify the max frame size in bytes,
rather than in fixed steps.
DSA calls change_mtu for the CPU port once the max MTU value among the
ports changes. As the max frame size is defined globally, the switch
is configured only when the call affects the CPU port.
The available specifications do not directly define the max supported
frame size, but it mentions a 16k limit. This driver will use the 0x3FFF
limit as it is used in the vendor API code. However, the switch sets the
max frame size to 16368 bytes (0x3FF0) after it resets.
change_mtu uses MTU size, or ethernet payload size, while the switch
works with frame size. The frame size is calculated considering the
ethernet header (14 bytes), a possible 802.1Q tag (4 bytes), the payload
size (MTU), and the Ethernet FCS (4 bytes). The CPU tag (8 bytes) is
consumed before the switch enforces the limit.
During setup, the driver will use the default 1500-byte MTU of DSA to
set the maximum frame size. The current sum will be
VLAN_ETH_HLEN+1500+ETH_FCS_LEN, which results in 1522 bytes. Although
it is lower than the previous initial value of 1536 bytes, the driver
will increase the frame size for a larger MTU. However, if something
requires more space without increasing the MTU, such as QinQ, we would
need to add the extra length to the rtl8365mb_port_change_mtu() formula.
MTU was tested up to 2018 (with 802.1Q) as that is as far as mt7620
(where rtl8367s is stacked) can go. The register was manually
manipulated byte-by-byte to ensure the MTU to frame size conversion was
correct. For frames without 802.1Q tag, the frame size limit will be 4
bytes over the required size.
There is a jumbo register, enabled by default at 6k frame size.
However, the jumbo settings do not seem to limit nor expand the maximum
tested MTU (2018), even when jumbo is disabled. More tests are needed
with a device that can handle larger frames.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit has replaced a ksz_write8() call to address
REG_PORT_5_CTRL_6 (0x56) with a ksz_set_xmii() -> ksz_pwrite8() call to
regs[P_XMII_CTRL_1], which is also defined as 0x56 for ksz8795_regs[].
The trouble is that, when compared to ksz_write8(), ksz_pwrite8() also
adjusts the register offset with the port base address. So in reality,
ksz_pwrite8(offset=0x56) accesses register 0x56 + 0x50 = 0xa6, which in
this switch appears to be unmapped, and the RGMII delay configuration on
the CPU port does nothing.
So if the switch wasn't fine with the RGMII delay configuration done
through pin strapping and relied on Linux to apply a different one in
order to pass traffic, this is now broken.
Using the offset translation logic imposed by ksz_pwrite8(), the correct
value for regs[P_XMII_CTRL_1] should have been 0x6 on ksz8795_regs[], in
order to really end up accessing register 0x56.
Static code analysis shows that, despite there being multiple other
accesses to regs[P_XMII_CTRL_1] in this driver, the only code path that
is applicable to ksz8795_regs[] and ksz8_dev_ops is ksz_set_xmii().
Therefore, the problem is isolated to RGMII delays.
In its current form, ksz8795_regs[] contains the same value for
P_XMII_CTRL_0 and for P_XMII_CTRL_1, and this raises valid suspicions
that writes made by the driver to regs[P_XMII_CTRL_0] might overwrite
writes made to regs[P_XMII_CTRL_1] or vice versa.
Again, static analysis shows that the only accesses to P_XMII_CTRL_0
from the driver are made from code paths which are not reachable with
ksz8_dev_ops. So the accesses made by ksz_set_xmii() are safe for this
switch family.
[ vladimiroltean: rewrote commit message ]
Fixes: c476bede4b ("net: dsa: microchip: ksz8795: use common xmii function")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230315231916.2998480-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://lore.kernel.org/r/20230314181824.56881-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are 3 classes of switch families that the driver is aware of, as
far as mv88e6xxx_change_mtu() is concerned:
- MTU configuration is available per port. Here, the
chip->info->ops->port_set_jumbo_size() method will be present.
- MTU configuration is global to the switch. Here, the
chip->info->ops->set_max_frame_size() method will be present.
- We don't know how to change the MTU. Here, none of the above methods
will be present.
Switch families MV88E6165, MV88E6191, MV88E6220, MV88E6250 and MV88E6290
fall in category 3.
The blamed commit has adjusted the MTU for all 3 categories by EDSA_HLEN
(8 bytes), resulting in a new maximum MTU of 1492 being reported by the
driver for these switches.
I don't have the hardware to test, but I do have a MV88E6390 switch on
which I can simulate this by commenting out its .port_set_jumbo_size
definition from mv88e6390_ops. The result is this set of messages at
probe time:
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 1
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 2
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 3
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 4
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 5
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 6
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 7
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 8
It is highly implausible that there exist Ethernet switches which don't
support the standard MTU of 1500 octets, and this is what the DSA
framework says as well - the error comes from dsa_slave_create() ->
dsa_slave_change_mtu(slave_dev, ETH_DATA_LEN).
But the error messages are alarming, and it would be good to suppress
them.
As a consequence of this unlikeliness, we reimplement mv88e6xxx_get_max_mtu()
and mv88e6xxx_change_mtu() on switches from the 3rd category as follows:
the maximum supported MTU is 1500, and any request to set the MTU to a
value larger than that fails in dev_validate_mtu().
Fixes: b9c587fed6 ("dsa: mv88e6xxx: Include tagger overhead when setting MTU for DSA and CPU ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/net/dsa/ocelot/ocelot_ext.c:143:34: error: ‘ocelot_ext_switch_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
drivers/net/dsa/microchip/ksz9477_i2c.c:84:34: error: ‘ksz9477_dt_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/net/dsa/ocelot/seville_vsc9953.c:1070:34: error: ‘seville_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will match mostly or only by DT table (even thought there is
regular ID table) so there is little benefit in of_match_ptr (this also
allows ACPI matching via PRP0001, even though it might not be relevant
here).
drivers/net/dsa/lan9303_i2c.c:97:34: error: ‘lan9303_i2c_of_match’ defined but not used [-Werror=unused-const-variable=]
drivers/net/dsa/lan9303_mdio.c:157:34: error: ‘lan9303_mdio_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/net/dsa/lantiq_gswip.c:1888:34: error: ‘xway_gphy_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ETS Qdisc support for KSZ9477 of switches. Current implementation is
limited to strict priority mode.
Tested on KSZ8563R with following configuration:
tc qdisc replace dev lan2 root handle 1: ets strict 4 \
priomap 3 3 2 2 1 1 0 0
ip link add link lan2 name v1 type vlan id 1 \
egress-qos-map 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7
and patched iperf3 version:
https://github.com/esnet/iperf/pull/1476
iperf3 -c 172.17.0.1 -b100M -l1472 -t100 -u -R --sock-prio 2
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ksz_setup_tc_mode() to make queue scheduling and shaping
configuration more visible.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As my testing on the MCM MT7530 switch on MT7621 SoC shows, setting the PLL
frequency does not affect MII modes other than trgmii on port 5 and port 6.
So the assumption is that the operation here called "setting the PLL
frequency" actually sets the frequency of the TRGMII TX clock.
Make it so that it and the rest of the trgmii setup run only when the
trgmii mode is used.
Tested rgmii and trgmii modes of port 6 on MCM MT7530 on MT7621AT Unielec
U7621-06 and standalone MT7530 on MT7623NI Bananapi BPI-R2.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230310073338.5836-2-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove now incorrect comment regarding port 5 as GMAC5. This is supposed to
be supported since commit 38f790a805 ("net: dsa: mt7530: Add support for
port 5") under mt7530_setup_port5().
Fixes: 38f790a805 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230310073338.5836-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MT7530 switch from the MT7621 SoC has 2 ports which can be set up as
internal: port 5 and 6. Arınç reports that the GMAC1 attached to port 5
receives corrupted frames, unless port 6 (attached to GMAC0) has been
brought up by the driver. This is true regardless of whether port 5 is
used as a user port or as a CPU port (carrying DSA tags).
Offline debugging (blind for me) which began in the linked thread showed
experimentally that the configuration done by the driver for port 6
contains a step which is needed by port 5 as well - the write to
CORE_GSWPLL_GRP2 (note that I've no idea as to what it does, apart from
the comment "Set core clock into 500Mhz"). Prints put by Arınç show that
the reset value of CORE_GSWPLL_GRP2 is RG_GSWPLL_POSDIV_500M(1) |
RG_GSWPLL_FBKDIV_500M(40) (0x128), both on the MCM MT7530 from the
MT7621 SoC, as well as on the standalone MT7530 from MT7623NI Bananapi
BPI-R2. Apparently, port 5 on the standalone MT7530 can work under both
values of the register, while on the MT7621 SoC it cannot.
The call path that triggers the register write is:
mt753x_phylink_mac_config() for port 6
-> mt753x_pad_setup()
-> mt7530_pad_clk_setup()
so this fully explains the behavior noticed by Arınç, that bringing port
6 up is necessary.
The simplest fix for the problem is to extract the register writes which
are needed for both port 5 and 6 into a common mt7530_pll_setup()
function, which is called at mt7530_setup() time, immediately after
switch reset. We can argue that this mirrors the code layout introduced
in mt7531_setup() by commit 42bc4fafe3 ("net: mt7531: only do PLL once
after the reset"), in that the PLL setup has the exact same positioning,
and further work to consolidate the separate setup() functions is not
hindered.
Testing confirms that:
- the slight reordering of writes to MT7530_P6ECR and to
CORE_GSWPLL_GRP1 / CORE_GSWPLL_GRP2 introduced by this change does not
appear to cause problems for the operation of port 6 on MT7621 and on
MT7623 (where port 5 also always worked)
- packets sent through port 5 are not corrupted anymore, regardless of
whether port 6 is enabled by phylink or not (or even present in the
device tree)
My algorithm for determining the Fixes: tag is as follows. Testing shows
that some logic from mt7530_pad_clk_setup() is needed even for port 5.
Prior to commit ca366d6c88 ("net: dsa: mt7530: Convert to PHYLINK
API"), a call did exist for all phy_is_pseudo_fixed_link() ports - so
port 5 included. That commit replaced it with a temporary "Port 5 is not
supported!" comment, and the following commit 38f790a805 ("net: dsa:
mt7530: Add support for port 5") replaced that comment with a
configuration procedure in mt7530_setup_port5() which was insufficient
for port 5 to work. I'm laying the blame on the patch that claimed
support for port 5, although one would have also needed the change from
commit c3b8e07909 ("net: dsa: mt7530: setup core clock even in TRGMII
mode") for the write to be performed completely independently from port
6's configuration.
Thanks go to Arınç for describing the problem, for debugging and for
testing.
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/netdev/f297c2c4-6e7c-57ac-2394-f6025d309b9d@arinc9.com/
Fixes: 38f790a805 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230307155411.868573-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During review of ocelot_ext, it created a private phylink instance
that wasn't necessary. This was removed for subsequent postings,
but the include file seems to have been left behind. Remove it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compiling a kernel which has both CONFIG_NET_DSA_MSCC_OCELOT_EXT
and CONFIG_MSCC_OCELOT_SWITCH enabled, the following error message will
be printed:
[ 5.266588] Error: Driver 'ocelot-switch' is already registered, aborting...
Rename the ocelot_ext.c driver to "ocelot-ext-switch" to avoid the name
duplication, and update the mfd_cell entry for its resources.
Fixes: 3d7316ac81 ("net: dsa: ocelot: add external ocelot switch control")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit did not properly convert the resource start/end format
into the DEFINE_RES_MEM_NAMED() start/length format, resulting in a
resource for vsc9959_imdio_res which is much longer than expected:
$ cat /proc/iomem
1f8000000-1f815ffff : pcie@1f0000000
1f8140000-1f815ffff : 0000:00:00.5
1f8148030-1f815006f : imdio
vs (correct)
$ cat /proc/iomem
1f8000000-1f815ffff : pcie@1f0000000
1f8140000-1f815ffff : 0000:00:00.5
1f8148030-1f814803f : imdio
Luckily it's not big enough to exceed the size of the parent resource
(pci_resource_end(pdev, VSC9959_IMDIO_PCI_BAR)), and it doesn't overlap
with anything else that the Linux driver uses currently, so the larger
than expected size isn't a practical problem that I can see. Although it
is clearly wrong in the /proc/iomem output.
Fixes: 044d447a80 ("net: dsa: felix: use DEFINE_RES_MEM_NAMED for resources")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the refactoring in the commit below, vsc9953_mdio_read() was
replaced with mscc_miim_read(), which has one extra step: it checks for
the MSCC_MIIM_DATA_ERROR bits before returning the result.
On T1040RDB, there are 8 QSGMII PCSes belonging to the switch, and they
are organized in 2 groups. First group responds to MDIO addresses 4-7
because QSGMIIACR1[MDEV_PORT] is 1, and the second group responds to
MDIO addresses 8-11 because QSGMIIBCR1[MDEV_PORT] is 2. I have double
checked that these values are correctly set in the SERDES, as well as
PCCR1[QSGMA_CFG] and PCCR1[QSGMB_CFG] are both 0b01.
mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 4 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 4 reg 0x5 MIIM_DATA 0x3da01, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR
As can be seen, the data in MIIM_DATA is still valid despite having the
MSCC_MIIM_DATA_ERROR bits set. The driver as introduced in commit
84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953
switch") was ignoring these bits, perhaps deliberately (although
unbeknownst to me).
This is an old IP and the hardware team cannot seem to be able to help
me track down a plausible reason for these failures. I'll keep
investigating, but in the meantime, this is a direct regression which
must be restored to a working state.
The only thing I can do is keep ignoring the errors as before.
Fixes: b996584523 ("net: dsa: ocelot: felix: utilize shared mscc-miim driver for indirect MDIO access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of KSZ9477 family switches provides EEE support. To enable it, we
just need to register set_mac_eee/set_mac_eee handlers and validate
supported chip version and port.
Currently supported chip variants are: KSZ8563, KSZ9477, KSZ9563,
KSZ9567, KSZ9893, KSZ9896, KSZ9897. KSZ8563 supports EEE only with
100BaseTX/Full. Other chips support 100BaseTX/Full and 1000BaseTX/Full.
Low Power Idle configuration is not supported and currently not
documented in the datasheets.
EEE PHY specific tunings are not documented in the switch datasheets, but can
overlap with KSZ9131 specification.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new user of MSCC_OCELOT_SWITCH_LIB was added, bringing back an old
link failure that was fixed with e5f3155267 ("ethernet: fix
PTP_1588_CLOCK dependencies"):
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_ptp_enable':
ocelot_ptp.c:(.text+0x8ee): undefined reference to `ptp_find_pin'
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_get_ts_info':
ocelot_ptp.c:(.text+0xd5d): undefined reference to `ptp_clock_index'
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_init_timestamp':
ocelot_ptp.c:(.text+0x15ca): undefined reference to `ptp_clock_register'
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_deinit_timestamp':
ocelot_ptp.c:(.text+0x16b7): undefined reference to `ptp_clock_unregister'
Add the same PTP dependency here, as well as in the MSCC_OCELOT_SWITCH_LIB
symbol itself to make it more obvious what is going on when the next
driver selects it.
Fixes: 3d7316ac81 ("net: dsa: ocelot: add external ocelot switch control")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20230209124435.1317781-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Frank reports that in a mt7530 setup where some ports are standalone and
some are in a VLAN-aware bridge, 8021q uppers of the standalone ports
lose their VLAN tag on xmit, as seen by the link partner.
This seems to occur because once the other ports join the VLAN-aware
bridge, mt7530_port_vlan_filtering() also calls
mt7530_port_set_vlan_aware(ds, cpu_dp->index), and this affects the way
that the switch processes the traffic of the standalone port.
Relevant is the PVC_EG_TAG bit. The MT7530 documentation says about it:
EG_TAG: Incoming Port Egress Tag VLAN Attribution
0: disabled (system default)
1: consistent (keep the original ingress tag attribute)
My interpretation is that this setting applies on the ingress port, and
"disabled" is basically the normal behavior, where the egress tag format
of the packet (tagged or untagged) is decided by the VLAN table
(MT7530_VLAN_EGRESS_UNTAG or MT7530_VLAN_EGRESS_TAG).
But there is also an option of overriding the system default behavior,
and for the egress tagging format of packets to be decided not by the
VLAN table, but simply by copying the ingress tag format (if ingress was
tagged, egress is tagged; if ingress was untagged, egress is untagged;
aka "consistent). This is useful in 2 scenarios:
- VLAN-unaware bridge ports will always encounter a miss in the VLAN
table. They should forward a packet as-is, though. So we use
"consistent" there. See commit e045124e93 ("net: dsa: mt7530: fix
tagged frames pass-through in VLAN-unaware mode").
- Traffic injected from the CPU port. The operating system is in god
mode; if it wants a packet to exit as VLAN-tagged, it sends it as
VLAN-tagged. Otherwise it sends it as VLAN-untagged*.
*This is true only if we don't consider the bridge TX forwarding offload
feature, which mt7530 doesn't support.
So for now, make the CPU port always stay in "consistent" mode to allow
software VLANs to be forwarded to their egress ports with the VLAN tag
intact, and not stripped.
Link: https://lore.kernel.org/netdev/trinity-e6294d28-636c-4c40-bb8b-b523521b00be-1674233135062@3c-app-gmx-bs36/
Fixes: e045124e93 ("net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230205140713.1609281-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When NET_DSA_MICROCHIP_KSZ_COMMON is built-in but PTP is a loadable
module, the ksz_ptp support still causes a link failure:
ld.lld-16: error: undefined symbol: ptp_clock_index
>>> referenced by ksz_ptp.c
>>> drivers/net/dsa/microchip/ksz_ptp.o:(ksz_get_ts_info) in archive vmlinux.a
This can happen if NET_DSA_MICROCHIP_KSZ8863_SMI is enabled, or
even if none of the KSZ9477_I2C/KSZ_SPI/KSZ8863_SMI ones are active
but only the common module is.
The most straightforward way to address this is to move the
dependency to NET_DSA_MICROCHIP_KSZ_PTP itself, which can now
only be enabled if both PTP_1588_CLOCK support is reachable
from NET_DSA_MICROCHIP_KSZ_COMMON. Alternatively, one could make
NET_DSA_MICROCHIP_KSZ_COMMON a hidden Kconfig symbol and extend the
PTP_1588_CLOCK_OPTIONAL dependency to NET_DSA_MICROCHIP_KSZ8863_SMI as
well, but that is a little more fragile.
Fixes: eac1ea2026 ("net: dsa: microchip: ptp: add the posix clock support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230130131808.1084796-1-arnd@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add control of an external VSC7512 chip.
Currently the four copper phy ports are fully functional. Communication to
external phys is also functional, but the SGMII / QSGMII interfaces are
currently non-functional.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the Felix driver would probe the ports and verify functionality, it
would fail if it hit single port mode that wasn't supported by the driver.
The initial case for the VSC7512 driver will have physical ports that
exist, but aren't supported by the driver implementation. Add the
OCELOT_PORT_MODE_NONE macro to handle this scenario, and allow the Felix
driver to continue with all the ports that are currently functional.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The architecture around the VSC7512 differs from existing felix drivers. In
order to add support for all the chip's features (pinctrl, MDIO, gpio) the
device had to be laid out as a multi-function device (MFD).
One difference between an MFD and a standard platform device is that the
regmaps are allocated to the parent device before the child devices are
probed. As such, there is no need for felix to initialize new regmaps in
these configurations, they can simply be requested from the parent device.
Add support for MFD configurations by performing this request from the
parent device.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The define FELIX_MAC_QUIRKS was used directly in the felix.c shared driver.
Other devices (VSC7512 for example) don't require the same quirks, so they
need to be configured on a per-device basis.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert qca8k to regmap read/write bulk API. The mgmt eth can write up
to 32 bytes of data at times. Currently we use a custom function to do
it but regmap now supports declaration of read/write bulk even without a
bus.
Drop the custom function and rework the regmap function to this new
implementation.
Rework the qca8k_fdb_read/write function to use the new
regmap_bulk_read/write as the old qca8k_bulk_read/write are now dropped.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and use QCA8K_ATU_TABLE_SIZE instead of hardcoding the ATU size with
a pure number and using sizeof on the array.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The build system currently complains:
scripts/Makefile.build:252: drivers/net/dsa/ocelot/Makefile:
felix.o is added to multiple modules: mscc_felix mscc_seville
Since felix.c holds the DSA glue layer, create a mscc_felix_dsa_lib.ko.
This is similar to how mscc_ocelot_switch_lib.ko holds a library for
configuring the hardware.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20230125145716.271355-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KSZ9477, KSZ9567, KSZ9563, KSZ8563 and LAN937x supports Credit based
shaper. To differentiate the chip supporting cbs, tc_cbs_supported
flag is introduced in ksz_chip_data.
And KSZ series has 16bit Credit increment registers whereas LAN937x has
24bit register. The value to be programmed in the credit increment is
determined using the successive multiplication method to convert decimal
fraction to hexadecimal fraction.
For example: if idleslope is 10000 and sendslope is -90000, then
bandwidth is 10000 - (-90000) = 100000.
The 10% bandwidth of 100Mbps means 10/100 = 0.1(decimal). This value has
to be converted to hexa.
1) 0.1 * 16 = 1.6 --> fraction 0.6 Carry = 1 (MSB)
2) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
3) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
4) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
5) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
6) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9 (LSB)
Now 0.1(decimal) becomes 0.199999(Hex).
If it is LAN937x, 24 bit value will be programmed to Credit Inc
register, 0x199999. For others 16 bit value will be prgrammed, 0x1999.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LAN937x family of switches has 8 queues per port where the KSZ switches
has 4 queues per port. By default, only one queue per port is enabled.
The queues are configurable in 2, 4 or 8. This patch add 8 number of
queues for LAN937x and 4 for other switches.
In the tag_ksz.c file, prioirty of the packet is queried using the skb
buffer and the corresponding value is updated in the tag.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Starting with commit eee16b1471 ("net: dsa: microchip: perform the
compatibility check for dev probed"), the KSZ switch driver now bails
out if it thinks the DT compatible doesn't match the actual chip ID
read back from the hardware:
ksz9477-switch 1-005f: Device tree specifies chip KSZ9893 but found
KSZ8563, please fix it!
For the KSZ8563, which used ksz_switch_chips[KSZ9893], this was fine
at first, because it indeed shares the same chip id as the KSZ9893.
Commit b449080956 ("net: dsa: microchip: add separate struct
ksz_chip_data for KSZ8563 chip") started differentiating KSZ9893
compatible chips by consulting the 0x1F register. The resulting breakage
was fixed for the SPI driver in the same commit by introducing the
appropriate ksz_switch_chips[KSZ8563], but not for the I2C driver.
Fix this for I2C-connected KSZ8563 now to get it probing again.
Fixes: b449080956 ("net: dsa: microchip: add separate struct ksz_chip_data for KSZ8563 chip").
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230120110933.1151054-1-a.fatoum@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Felix (VSC9959) has a DEV_GMII:MM_CONFIG block composed of 2 registers
(ENABLE_CONFIG and VERIF_CONFIG). Because the MAC Merge statistics and
pMAC statistics are already in the Ocelot switch lib even if just Felix
supports them, I'm adding support for the whole MAC Merge layer in the
common Ocelot library too.
There is an interrupt (shared with the PTP interrupt) which signals
changes to the MM verification state. This is done because the
preemptible traffic classes should be committed to hardware only once
the verification procedure has declared the link partner of being
capable of receiving preemptible frames.
We implement ethtool getters and setters for the MAC Merge layer state.
The "TX enabled" and "verify status" are taken from the IRQ handler,
using a mutex to ensure serialized access.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix VSC9959 switch supports frame preemption and has a MAC Merge
layer. In addition to the structured stats that exist for the eMAC,
export the counters associated with its pMAC (pause, RMON, MAC, PHY,
control) plus the high-level MAC Merge layer stats. The unstructured
ethtool counters, as well as the rtnl_link_stats64 were left to report
only the eMAC counters.
Because statistics processing is quite self-contained in ocelot_stats.c
now, I've opted for introducing an ocelot->mm_supported bool, based on
which the common switch lib does everything, rather than pushing the
TSN-specific code in felix_vsc9959.c, as happens for other TSN stuff.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO core should not pass a C45 request via the C22 API call any
more. So remove the tests from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While the prior patch moved the adjust_link code into the
phylink_mac_link_up api, this patch cleans it up and adds the setting the
port's flow control based on the phylink_mac_link_up input parameters.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the adjust_link api with the phylink apis that provide
equivalent functionality.
The remaining functionality from the adjust_link is now covered in the
phylink_mac_link_up api.
Removes:
.adjust_link
Adds:
.phylink_get_caps
.phylink_mac_link_up
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparing to move the adjust_link logic into the phylink_mac_link_up
api, change the macro used to check for the cpu port. In
phylink_mac_link_up, the phydev pointer passed in for the CPU port is
NULL, so we can't keep using phy_is_pseudo_fixed_link(phydev).
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the regmap_write() is over a slow bus that will sleep, we can speed up
the boot-up time a bit by not bothering to clear a bit that is already
clear.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While it is highly unlikely a read will ever fail, This code fragment is
now in a function that allows us to return an error code. A read failure
here will cause the lan9303_probe to fail.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparing to remove the .adjust_link api, I am moving the one-time
initialization of the device's Turbo Mode bit into a different execution
path. This code clears (disables) the Turbo Mode bit which is never used
by this driver. Turbo Mode is a non-standard mode that would allow the
100Mbps RMII interface to run at 200Mbps.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whitespace preparatory patch, making the dsa_switch_ops table consistent.
No code is added or removed.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to return negative error codes here but the copy_to/from_user()
functions return the number of bytes remaining to be copied.
Fixes: c59e12a140 ("net: dsa: microchip: ptp: Initial hardware time stamping support")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/Y8fJxSvbl7UNVHh/@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ALU table entry 2 register in KSZ9477 have bit positions reserved for
forwarding port map. This field is referred in ksz9477_fdb_del() for
clearing forward port map and alu table.
But current fdb_del refer ALU table entry 3 register for accessing forward
port map. Update ksz9477_fdb_del() to get forward port map from correct
alu table entry register.
With this bug, issue can be observed while deleting static MAC entries.
Delete any specific MAC entry using "bridge fdb del" command. This should
clear all the specified MAC entries. But it is observed that entries with
self static alone are retained.
Tested on LAN9370 EVB since ksz9477_fdb_del() is used common across
LAN937x and KSZ series.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230118174735.702377-1-rakesh.sankaranarayanan@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The T1 MDIO bus driver can perform both C22 and C45 transfers. Create
separate functions for each and register the C45 versions using the
new API calls where appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sja1105 MDIO bus driver only supports C45 transfers. Update the
function names to make this clear, pass the mmd as a parameter, and
register the accessors to the _c45 ops of the bus driver structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mt7530 does support C45, but its uses a mix of registering its MDIO
bus and providing its private MDIO bus to the DSA core, too. This makes
the change a bit more complex.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch receives management traffic such as STP and LLDP. However, PTP
messages are not received, only transmitted.
Ideally, the switch would trap all PTP messages to the management CPU. This
particular switch has a PTP block which identifies PTP messages and traps them
to a dedicated port. There is a register to program this destination. This is
not used at the moment.
Therefore, program it to the same port as the MGMT traffic is trapped to. This
allows to receive PTP messages as soon as timestamping is enabled.
In addition, the datasheet mentions that this register is not valid e.g., for
6190 variants. So, add a new PTP operation which is added for the 6390 and 6290
devices.
Tested simply like this on Marvell 88E6390, revision 1:
|/ # ptp4l -2 -i lan4 --tx_timestamp_timeout=40 -m
|[...]
|ptp4l[147.450]: master offset 56 s2 freq +1262 path delay 413
|ptp4l[148.450]: master offset 22 s2 freq +1244 path delay 434
|ptp4l[149.450]: master offset 5 s2 freq +1234 path delay 446
|ptp4l[150.451]: master offset 3 s2 freq +1233 path delay 451
|ptp4l[151.451]: master offset 1 s2 freq +1232 path delay 451
|ptp4l[152.451]: master offset -3 s2 freq +1229 path delay 451
|ptp4l[153.451]: master offset 9 s2 freq +1240 path delay 451
Link: https://lore.kernel.org/r/CAFSKS=PJBpvtRJxrR4sG1hyxpnUnQpiHg4SrUNzAhkWnyt9ivg@mail.gmail.com
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enetc MDIO bus driver can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new API calls where appropriate.
This driver is shared with the Felix DSA switch, so update that at the
same time.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is difference in implementation of per_out pins between KSZ9563
and LAN937x. In KSZ9563, Timestamping control register (0x052C) bit 6,
if 1 - timestamp input and 0 - trigger output. But it is opposite for
LAN937x 1 - trigger output and 0 - timestamp input.
As per per_out gpio pins, KSZ9563 has four Led pins and two dedicated
gpio pins. But in LAN937x dedicated gpio pins are removed instead there
are up to 10 LED pins out of which LED_0 and LED_1 can be mapped to PTP
tou 0, 1 or 2. This patch sets the bit 6 in 0x052C register and
configure the LED override and source register for LAN937x series of
switches alone.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN937x series of switches support 2 step timestamping mechanism. There
are timestamp correction calculation performed in ksz_rcv_timestamp and
ksz_xmit_timestamp which are applicable only for p2p1step. To check
whether the 2 step is enabled or not in tag_ksz.c introduced the helper
function in taggger_data to query it from ksz_ptp.c. Based on whether 2
step is enabled or not, timestamp calculation are performed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two programmable pins available for Trigger output unit to
generate periodic pulses. This patch add verify_pin for the available 2
pins and configure it with respect to GPIO index for the TOU unit.
Tested using testptp
./testptp -i 0 -L 0,2
./testptp -i 0 -d /dev/ptp0 -p 1000000000
./testptp -i 1 -L 1,2
./testptp -i 1 -d /dev/ptp0 -p 100000000
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN937x and KSZ PTP supported switches has Three Trigger output unit.
This TOU can used to generate the periodic signal for PTP. TOU has the
cycle width register of 32 bit in size and period width register of 24
bit, each value is of 8ns so the pulse width can be maximum 125ms.
Tested using ./testptp -d /dev/ptp0 -p 1000000000 -w 100000000 for
generating the 10ms pulse width
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For PDelay_Resp messages we will likely have a negative value in the
correction field. The switch hardware cannot correctly update such
values (produces an off by one error in the UDP checksum), so it must be
moved to the time stamp field in the tail tag. Format of the correction
field is 48 bit ns + 16 bit fractional ns. After updating the
correction field, clone is no longer required hence it is freed.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the routines for transmission of ptp packets. When the
ptp pdelay_req packet to be transmitted, it uses the deferred xmit
worker to schedule the packets.
During irq_setup, interrupt for Sync, Pdelay_req and Pdelay_rsp are
enabled. So interrupt is triggered for all three packets. But for
p2p1step, we require only time stamp of Pdelay_req packet. Hence to
avoid posting of the completion from ISR routine for Sync and
Pdelay_resp packets, ts_en flag is introduced. This controls which
packets need to processed for timestamp.
After the packet is transmitted, ISR is triggered. The time at which
packet transmitted is recorded to separate register.
This value is reconstructed to absolute time and posted to the user
application through socket error queue.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx Timestamping is done through 4 additional bytes in tail tag.
Whenever the ptp packet is received, the 4 byte hardware time stamped
value is added before 1 byte tail tag. Also, bit 7 in tail tag indicates
it as PTP frame. This 4 byte value is extracted from the tail tag and
reconstructed to absolute time and assigned to skb hwtstamp.
If the packet received in PDelay_Resp, then partial ingress timestamp
is subtracted from the correction field. Since user space tools expects
to be done in hardware.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP Interrupt mask and status register differ from the global and port
interrupt mechanism by two methods. One is that for global/port
interrupt enabling we have to clear the bit but for ptp interrupt we
have to set the bit. And other is bit12:0 is reserved in ptp interrupt
registers. This forced to not use the generic implementation of
global/port interrupt method routine. This patch implement the ptp
interrupt mechanism to read the timestamp register for sync, pdelay_req
and pdelay_resp.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is used for reconstructing the absolute time from the 32bit
hardware time stamping value. The do_aux ioctl is used for reading the
ptp hardware clock and store it to global variable.
The timestamped value in tail tag during rx and register during tx are
32 bit value (2 bit seconds and 30 bit nanoseconds). The time taken to
read entire ptp clock will be time consuming. In order to speed up, the
software clock is maintained. This clock time will be added to 32 bit
timestamp to get the absolute time stamp.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PTP is enabled in hardware bit 6 of PTP_MSG_CONF1 register, the
transmit frame needs additional 4 bytes before the tail tag. It is
needed for all the transmission packets irrespective of PTP packets or
not.
The 4-byte timestamp field is 0 for frames other than Pdelay_Resp. For
the one-step Pdelay_Resp, the switch needs the receive timestamp of the
Pdelay_Req message so that it can put the turnaround time in the
correction field.
Since PTP has to be enabled for both Transmission and reception
timestamping, driver needs to track of the tx and rx setting of the all
the user ports in the switch.
Two flags hw_tx_en and hw_rx_en are added in ksz_port to track the
timestampping setting of each port. When any one of ports has tx or rx
timestampping enabled, bit 6 of PTP_MSG_CONF1 is set and it is indicated
to tag_ksz.c through tagger bytes. This flag adds 4 additional bytes to
the tail tag. When tx and rx timestamping of all the ports are disabled,
then 4 bytes are not added.
Tested using hwstamp -i <interface>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> # mostly api
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the routine for get_ts_info, hwstamp_get, set. This enables
the PTP support towards userspace applications such as linuxptp.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implement routines (adjfine, adjtime, gettime and settime)
for manipulating the chip's PTP clock. It registers the ptp caps
to posix clock register.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> # mostly api
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The global2 SMI MDIO bus driver can perform both C22 and C45
transfers. Create separate functions for each and register the C45
versions using the new API calls where appropriate. Update the SERDES
code to make use of these new accessors.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This implementation for the Marvell mv88e6xxx chip series is based on
handling ATU miss violations occurring when packets ingress on a port
that is locked with learning on. This will trigger a
SWITCHDEV_FDB_ADD_TO_BRIDGE event, which will result in the bridge module
adding a locked FDB entry. This bridge FDB entry will not age out as
it has the extern_learn flag set.
Userspace daemons can listen to these events and either accept or deny
access for the host, by either replacing the locked FDB entry with a
simple entry or leave the locked entry.
If the host MAC address is already present on another port, a ATU
member violation will occur, but to no real effect, and the packet will
be dropped in hardware. Statistics on these violations can be shown with
the command and example output of interest:
ethtool -S ethX
NIC statistics:
...
atu_member_violation: 5
atu_miss_violation: 23
...
Where ethX is the interface of the MAB enabled port.
Furthermore, as added vlan interfaces where the vid is not added to the
VTU will cause ATU miss violations reporting the FID as
MV88E6XXX_FID_STANDALONE, we need to check and skip the miss violations
handling in this case.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As only the hardware access functions up til and including
mv88e6xxx_g1_atu_mac_read() called under the interrupt handler
need to take the chip lock, we release the chip lock after this call.
The follow up code that handles the violations can run without the
chip lock held.
In further patches, the violation handler function will even be
incompatible with having the chip lock held. This due to an AB/BA
ordering inversion with rtnl_lock().
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The default return value -EOPNOTSUPP of mv88e6xxx_port_bridge_flags()
came from the return value of the DSA method port_egress_floods() in
commit 4f85901f00 ("net: dsa: mv88e6xxx: add support for bridge flags"),
but the DSA API was changed in commit a8b659e7ff ("net: dsa: act as
passthrough for bridge port flags"), resulting in the return value
-EOPNOTSUPP not being valid anymore, and sections for new flags will not
need to set the return value to zero on success, as with the new mab flag
added in a following patch.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Improve mdio master read/write by using singe mii read/write lo/hi.
In a read and write we need to poll the mdio master regs in a busy loop
to check for a specific bit present in the upper half of the reg. We can
ignore the other half since it won't contain useful data. This will save
an additional useless read for each read and write operation.
In a read operation the returned data is present in the mdio master reg
lower half. We can ignore the other half since it won't contain useful
data. This will save an additional useless read for each read operation.
In a read operation it's needed to just set the hi half of the mdio
master reg as the lo half will be replaced by the result. This will save
an additional useless write for each read operation.
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may be useful to read/write just the lo or hi half of a reg.
This is especially useful for phy poll with the use of mdio master.
The mdio master reg is composed by the first 16 bit related to setup and
the other half with the returned data or data to write.
Refactor the mii function to permit single mii read/write of lo or hi
half of the reg.
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2481d206fa.
The Documentation is very confusing about the topic.
The cache logic for hi and lo is wrong and actually miss some regs to be
actually written.
What the Documentation actually intended was that it's possible to skip
writing hi OR lo if half of the reg is not needed to be written or read.
Revert the change in favor of a better and correct implementation.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
The assumption that Documentation was right about how this value work was
wrong. It was discovered that the length value of the mgmt header is in
step of word size.
As an example to process 4 byte of data the correct length to set is 2.
To process 8 byte 4, 12 byte 6, 16 byte 8...
Odd values will always return the next size on the ack packet.
(length of 3 (6 byte) will always return 8 bytes of data)
This means that a value of 15 (0xf) actually means reading/writing 32 bytes
of data instead of 16 bytes. This behaviour is totally absent and not
documented in the switch Documentation.
In fact from Documentation the max value that mgmt eth can process is
16 byte of data while in reality it can process 32 bytes at once.
To handle this we always round up the length after deviding it for word
size. We check if the result is odd and we round another time to align
to what the switch will provide in the ack packet.
The workaround for the length limit of 15 is still needed as the length
reg max value is 0xf(15)
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Fixes: 90386223f4 ("net: dsa: qca8k: add support for larger read/write size with mgmt Ethernet")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP hardware timestamping related objects are not linked when PTP
support for MV88E6xxx (NET_DSA_MV88E6XXX_PTP) is disabled, therefore
NET_DSA_MV88E6XXX should not depend on PTP_1588_CLOCK_OPTIONAL
regardless of NET_DSA_MV88E6XXX_PTP.
Instead, condition more strictly on how NET_DSA_MV88E6XXX_PTP's
dependencies are met, making sure that it cannot be enabled when
NET_DSA_MV88E6XXX=y and PTP_1588_CLOCK=m.
In other words, this commit allows NET_DSA_MV88E6XXX to be built-in
while PTP_1588_CLOCK is a module, as long as NET_DSA_MV88E6XXX_PTP is
prevented from being enabled.
Fixes: e5f3155267 ("ethernet: fix PTP_1588_CLOCK dependencies")
Signed-off-by: Johnny S. Lee <foss@jsl.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ swithes used interrupts for detecting the phy link up and down.
During registering the interrupt handler, it used IRQF_TRIGGER_FALLING
flag. But this flag has to be retrieved from device tree instead of hard
coding in the driver, so removing the flag.
Fixes: ff319a6448 ("net: dsa: microchip: move interrupt handling logic from lan937x to ksz_common")
Reported-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20221213101440.24667-1-arun.ramadoss@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King correctly pointed out that the MAC_2500FD capability is
already added for port 5 (if not in RGMII mode) and port 6 (which only
supports SGMII) by mt7531_mac_port_get_caps. Remove the reduntant
setting of this capability flag which was added by a previous commit.
Fixes: e19de30d20 ("net: dsa: mt7530: add support for in-band link status")
Reported-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/Y5qY7x6la5TxZxzX@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the blamed commit, it was not noticed that one implementation of
chip->info->ops->phylink_get_caps(), called by mv88e6xxx_get_caps(),
may access hardware registers, and in doing so, it takes the
mv88e6xxx_reg_lock(). Namely, this is mv88e6352_phylink_get_caps().
This is a problem because mv88e6xxx_get_caps(), apart from being
a top-level function (method invoked by dsa_switch_ops), is now also
directly called from mv88e6xxx_setup_port(), which runs under the
mv88e6xxx_reg_lock() taken by mv88e6xxx_setup(). Therefore, when running
on mv88e6352, the reg_lock would be acquired a second time and the
system would deadlock on driver probe.
The things that mv88e6xxx_setup() can compete with in terms of register
access with are the IRQ handlers and MDIO bus operations registered by
mv88e6xxx_probe(). So there is a real need to acquire the register lock.
The register lock can, in principle, be dropped and re-acquired pretty
much at will within the driver, as long as no operations that involve
waiting for indirect access to complete (essentially, callers of
mv88e6xxx_smi_direct_wait() and mv88e6xxx_wait_mask()) are interrupted
with the lock released. However, I would guess that in mv88e6xxx_setup(),
the critical section is kept open for such a long time just in order to
optimize away multiple lock/unlock operations on the registers.
We could, in principle, drop the reg_lock right before the
mv88e6xxx_setup_port() -> mv88e6xxx_get_caps() call, and
re-acquire it immediately afterwards. But this would look ugly, because
mv88e6xxx_setup_port() would release a lock which it didn't acquire, but
the caller did.
A cleaner solution to this issue comes from the observation that struct
mv88e6xxxx_ops methods generally assume they are called with the
reg_lock already acquired. Whereas mv88e6352_phylink_get_caps() is more
the exception rather than the norm, in that it acquires the lock itself.
Let's enforce the same locking pattern/convention for
chip->info->ops->phylink_get_caps() as well, and make
mv88e6xxx_get_caps(), the top-level function, acquire the register lock
explicitly, for this one implementation that will access registers for
port 4 to work properly.
This means that mv88e6xxx_setup_port() will no longer call the top-level
function, but the low-level mv88e6xxx_ops method which expects the
correct calling context (register lock held).
Compared to chip->info->ops->phylink_get_caps(), mv88e6xxx_get_caps()
also fixes up the supported_interfaces bitmap for internal ports, since
that can be done generically and does not require per-switch knowledge.
That's code which will no longer execute, however mv88e6xxx_setup_port()
doesn't need that. It just needs to look at the mac_capabilities bitmap.
Fixes: cc1049ccee ("net: dsa: mv88e6xxx: fix speed setting for CPU/DSA ports")
Reported-by: Maksim Kiselev <bigunclemax@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20221214110120.3368472-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Merge in the left-over fixes before the net-next pull-request.
net/mptcp/subflow.c
d3295fee3c ("mptcp: use proper req destructor for IPv6")
36b122baf6 ("mptcp: add subflow_v(4,6)_send_synack()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It is possible to trigger these VTU violation messages very easily,
it's only necessary to send packets with an unknown VLAN ID to a port
that belongs to a VLAN-aware bridge.
Do a similar thing as for ATU violation messages, and hide them in the
kernel's trace buffer.
New usage model:
$ trace-cmd list | grep mv88e6xxx
mv88e6xxx
mv88e6xxx:mv88e6xxx_vtu_miss_violation
mv88e6xxx:mv88e6xxx_vtu_member_violation
$ trace-cmd report
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In applications where the switch ports must perform 802.1X based
authentication and are therefore locked, ATU violation interrupts are
quite to be expected as part of normal operation. The problem is that
they currently spam the kernel log, even if rate limited.
Create a series of trace points, all derived from the same event class,
which log these violations to the kernel's trace buffer, which is both
much faster and much easier to ignore than printing to a serial console.
New usage model:
$ trace-cmd list | grep mv88e6xxx
mv88e6xxx
mv88e6xxx:mv88e6xxx_atu_full_violation
mv88e6xxx:mv88e6xxx_atu_miss_violation
mv88e6xxx:mv88e6xxx_atu_member_violation
$ trace-cmd record -e mv88e6xxx sleep 10
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When an ATU violation occurs, the switch uses the ATU FID register to
report the FID of the MAC address that incurred the violation. It would
be good for the driver to know the FID value for purposes such as
logging and CPU-based authentication.
Up until now, the driver has been calling the mv88e6xxx_g1_atu_op()
function to read ATU violations, but that doesn't do exactly what we
want, namely it calls mv88e6xxx_g1_atu_fid_write() with FID 0.
(side note, the documentation for the ATU Get/Clear Violation command
says that writes to the ATU FID register have no effect before the
operation starts, it's only that we disregard the value that this
register provides once the operation completes)
So mv88e6xxx_g1_atu_fid_write() is not what we want, but rather
mv88e6xxx_g1_atu_fid_read(). However, the latter doesn't exist, we need
to write it.
The remainder of mv88e6xxx_g1_atu_op() except for
mv88e6xxx_g1_atu_fid_write() is still needed, namely to send a
GET_CLR_VIOLATION command to the ATU. In principle we could have still
kept calling mv88e6xxx_g1_atu_op(), but the MDIO writes to the ATU FID
register are pointless, but in the interest of doing less CPU work per
interrupt, write a new function called mv88e6xxx_g1_read_atu_violation()
and call it.
The FID will be the port default FID as set by mv88e6xxx_port_set_fid()
if the VID from the packet cannot be found in the VTU. Otherwise it is
the FID derived from the VTU entry associated with that VID.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the MV88E6XXX_PORT_ASSOC_VECTOR_INT_AGE_OUT bit (interrupt on
age out) is not enabled by the driver, and as a result, the print for
age out violations is dead code.
Remove it until there is some way for this to be triggered.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch fixes an issue where a read failure of a port statistic counter
will return unknown results. While it is highly unlikely the read will
ever fail, it is much cleaner to return a zero for the stat count.
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221209153502.7429-1-jerry.ray@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SJA1105 family has 45 L2 policing table entries
(SJA1105_MAX_L2_POLICING_COUNT) and SJA1110 has 110
(SJA1110_MAX_L2_POLICING_COUNT). Keeping the table structure but
accounting for the difference in port count (5 in SJA1105 vs 10 in
SJA1110) does not fully explain the difference. Rather, the SJA1110 also
has L2 ingress policers for multicast traffic. If a packet is classified
as multicast, it will be processed by the policer index 99 + SRCPORT.
The sja1105_init_l2_policing() function initializes all L2 policers such
that they don't interfere with normal packet reception by default. To have
a common code between SJA1105 and SJA1110, the index of the multicast
policer for the port is calculated because it's an index that is out of
bounds for SJA1105 but in bounds for SJA1110, and a bounds check is
performed.
The code fails to do the proper thing when determining what to do with the
multicast policer of port 0 on SJA1105 (ds->num_ports = 5). The "mcast"
index will be equal to 45, which is also equal to
table->ops->max_entry_count (SJA1105_MAX_L2_POLICING_COUNT). So it passes
through the check. But at the same time, SJA1105 doesn't have multicast
policers. So the code programs the SHARINDX field of an out-of-bounds
element in the L2 Policing table of the static config.
The comparison between index 45 and 45 entries should have determined the
code to not access this policer index on SJA1105, since its memory wasn't
even allocated.
With enough bad luck, the out-of-bounds write could even overwrite other
valid kernel data, but in this case, the issue was detected using KASAN.
Kernel log:
sja1105 spi5.0: Probed switch chip: SJA1105Q
==================================================================
BUG: KASAN: slab-out-of-bounds in sja1105_setup+0x1cbc/0x2340
Write of size 8 at addr ffffff880bd57708 by task kworker/u8:0/8
...
Workqueue: events_unbound deferred_probe_work_func
Call trace:
...
sja1105_setup+0x1cbc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Allocated by task 8:
...
sja1105_setup+0x1bcc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Fixes: 38fbe91f22 ("net: dsa: sja1105: configure the multicast policers, if present")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Radu Nicolae Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20221207132347.38698-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ethernet-controller dt-schema, mostly pushed forward by Linux, has
the "internal" PHY mode for denoting MAC connections to an internal PHY.
U-Boot may provide device tree blobs where this phy-mode is specified,
so make the Linux driver accept them.
It appears that the current behavior with phy-mode = "internal" was
introduced when mv88e6xxx started reporting supported_interfaces to
phylink. Prior to that, I don't think it would have any issues accepting
this phy-mode.
Fixes: d4ebf12bce ("net: dsa: mv88e6xxx: populate supported_interfaces and mac_capabilities")
Link: https://lore.kernel.org/linux-arm-kernel/20221205172709.kglithpbhdbsakvd@skbuf/T/
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Tim Harvey <tharvey@gateworks.com> # imx6q-gw904.dts
Link: https://lore.kernel.org/r/20221205194845.2131161-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
To make the code more comparable to KSZ9477 code, move DSA
configurations to the same location.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
KSZ8795 and KSZ9477 compatible series of switches use global max frame
size configuration register. So, enable MTU normalization for this reason.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make MTU configurable on KSZ87xx and KSZ88xx series of switches.
Before this patch, pre-configured behavior was different on different
switch series, due to opposite meaning of the same bit:
- KSZ87xx: Reg 4, Bit 1 - if 1, max frame size is 1532; if 0 - 1514
- KSZ88xx: Reg 4, Bit 1 - if 1, max frame size is 1514; if 0 - 1532
Since the code was telling "... SW_LEGAL_PACKET_DISABLE, true)", I
assume, the idea was to set max frame size to 1532.
With this patch, by setting MTU size 1500, both switch series will be
configured to the 1532 frame limit.
This patch was tested on KSZ8873.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add ksz_rmw8(), it will be used in the next patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If we have global MTU configuration, it is enough to configure it on CPU
port only.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are no HW specific registers, so we can process all of them
in one location.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Arun Ramadoss <arun.ramadoss@microchip.com> (KSZ9893 and LAN937x)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver name is available in device_driver::name. Right now,
drivers still have to report this piece of information themselves in
their devlink_ops::info_get callback function.
In order to factorize code, make devlink_nl_info_fill() add the driver
name attribute.
Now that the core sets the driver name attribute, drivers are not
supposed to call devlink_info_driver_name_put() anymore. Remove
devlink_info_driver_name_put() and clean-up all the drivers using this
function in their callback.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Tested-by: Ido Schimmel <idosch@nvidia.com> # mlxsw
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch changes the reported ethtool statistics for the lan9303
family of parts covered by this driver.
The TxUnderRun statistic label is renamed to RxShort to accurately
reflect what stat the device is reporting. I did not reorder the
statistics as that might cause problems with existing user code that
are expecting the stats at a certain offset.
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221128193559.6572-1-jerry.ray@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no reason that I can see why the no-op tagging protocol should
be registered manually, so make it a module and make all drivers which
have any sort of reference to DSA_TAG_PROTO_NONE select it.
Note that I don't know if ksz_get_tag_protocol() really needs this,
or if it's just the logic which is poorly written. All switches seem to
have their own tagging protocol, and DSA_TAG_PROTO_NONE is just a
fallback that never gets used.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ever since commit 4d1d157fb6 ("net: mscc: ocelot: share the common stat
definitions between all drivers") the stats_layout entry in ocelot and
felix drivers have become redundant. Remove the unnecessary code.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
You'd think people know that the internal 100BASE-TX PHY on the SJA1110
responds only to clause 22 MDIO transactions, but they don't :)
When a clause 45 transaction is attempted, sja1105_base_tx_mdio_read()
and sja1105_base_tx_mdio_write() don't expect "reg" to contain bit 30
set (MII_ADDR_C45) and pack this value into the SPI transaction buffer.
But the field in the SPI buffer has a width smaller than 30 bits, so we
see this confusing message from the packing() API rather than a proper
rejection of C45 transactions:
Call trace:
dump_stack+0x1c/0x38
sja1105_pack+0xbc/0xc0 [sja1105]
sja1105_xfer+0x114/0x2b0 [sja1105]
sja1105_xfer_u32+0x44/0xf4 [sja1105]
sja1105_base_tx_mdio_read+0x44/0x7c [sja1105]
mdiobus_read+0x44/0x80
get_phy_c45_ids+0x70/0x234
get_phy_device+0x68/0x15c
fwnode_mdiobus_register_phy+0x74/0x240
of_mdiobus_register+0x13c/0x380
sja1105_mdiobus_register+0x368/0x490 [sja1105]
sja1105_setup+0x94/0x119c [sja1105]
Cannot store 401d2405 inside bits 24-4 (would truncate)
Fixes: 5a8f09748e ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the custom implementation of phylink_validate() in favor of the
generic one, which requires config->mac_capabilities to be set.
This was used up until now because of the possibility of being paired
with Aquantia PHYs with support for rate matching. The phylink framework
gained generic support for these, and knows to advertise all 10/100/1000
lower speed link modes when our SERDES protocol is 2500base-x
(fixed speed).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Probe functions uses normal dev_err() to check error conditions
and print messages. Replace dev_err() with dev_err_probe() to
have more standardized format and error logging.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ8563 have three port interrupts: PTP, PHY and ACL. Add
port_nirq as 3 for KSZ8563 inside ksz_chip_data.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add status validation for port register write inside
lan937x_change_mtu. ksz_pwrite and ksz_pread api's are
updated with return type int (Reference patch mentioned
below). Update lan937x_change_mtu with status validation
for ksz_pwrite16().
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20220826105634.3855578-6-o.rempel@pengutronix.de/
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add device irq in i2c probe function.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add KSZ9563 inside ksz_switch_chips structure with
port_nirq as 3. KSZ9563 use KSZ9893 switch parameters
but port_nirq count is 3 for KSZ9563 whereas 2 for
KSZ9893. Add KSZ9563 inside ksz_switch_chips as a separate
member and from device tree map compatible string into
KSZ9563 inside ksz_spi.c and ksz9477_i2c.c.
Global Chip ID 1 and 2 registers read value 9893, select
sku based on Global Chip ID 4 Register which read 0x1c
for KSZ9563.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the .port_set_rgmii_delay hook is missing for the 88E6320
family, which causes failure to retrieve an IP address via DHCP.
Add mv88e6320_port_set_rgmii_delay() that allows applying the RGMII
delay for ports 2, 5, and 6, which are the only ports that can be used
in RGMII mode.
Tested on a custom i.MX8MN board connected to an 88E6320 switch.
This change also applies safely to the 88E6321 variant.
The only difference between 88E6320 versus 88E6321 is the temperature
grade and pinout.
They share exactly the same MDIO register map for ports 2, 5, and 6,
which are the only ports that can be used in RGMII mode.
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
[fabio: Improved commit log and extended it to mv88e6321_ops]
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221028163158.198108-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kmemleak reported memory leaks in dsa_loop_init():
kmemleak: 12 new suspected memory leaks
unreferenced object 0xffff8880138ce000 (size 2048):
comm "modprobe", pid 390, jiffies 4295040478 (age 238.976s)
backtrace:
[<000000006a94f1d5>] kmalloc_trace+0x26/0x60
[<00000000a9c44622>] phy_device_create+0x5d/0x970
[<00000000d0ee2afc>] get_phy_device+0xf3/0x2b0
[<00000000dca0c71f>] __fixed_phy_register.part.0+0x92/0x4e0
[<000000008a834798>] fixed_phy_register+0x84/0xb0
[<0000000055223fcb>] dsa_loop_init+0xa9/0x116 [dsa_loop]
...
There are two reasons for memleak in dsa_loop_init().
First, fixed_phy_register() create and register phy_device:
fixed_phy_register()
get_phy_device()
phy_device_create() # freed by phy_device_free()
phy_device_register() # freed by phy_device_remove()
But fixed_phy_unregister() only calls phy_device_remove().
So the memory allocated in phy_device_create() is leaked.
Second, when mdio_driver_register() fail in dsa_loop_init(),
it just returns and there is no cleanup for phydevs.
Fix the problems by catching the error of mdio_driver_register()
in dsa_loop_init(), then calling both fixed_phy_unregister() and
phy_device_free() to release phydevs.
Also add a function for phydevs cleanup to avoid duplacate.
Fixes: 98cd1552ea ("net: dsa: Mock-up driver")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch sends autocast mib in little-endian. This is problematic for
big-endian system as the values needs to be converted.
Fix this by converting each mib value to cpu byte order.
Fixes: 5c957c7ca7 ("net: dsa: qca8k: add support for mib autocast in Ethernet packet")
Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The header and the data of the skb for the inband mgmt requires
to be in little-endian. This is problematic for big-endian system
as the mgmt header is written in the cpu byte order.
Fix this by converting each value for the mgmt header and data to
little-endian, and convert to cpu byte order the mgmt header and
data sent by the switch.
Fixes: 5950c7c0a6 ("net: dsa: qca8k: add support for mgmt read/write in Ethernet packet")
Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixes all over the tree. Other subsystems depending on this change
have been asked to pull an immutable topic branch for this.
* new driver for Microchip PCI1xxxx switch
* heavy refactoring of the Mellanox BlueField driver
* we prefer async probe in the i801 driver now
* the rest is usual driver updates (support for more SoCs, some
refactoring, some feature additions)
-----BEGIN PGP SIGNATURE-----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=arni
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- 'remove' callback converted to return void. Big change with trivial
fixes all over the tree. Other subsystems depending on this change
have been asked to pull an immutable topic branch for this.
- new driver for Microchip PCI1xxxx switch
- heavy refactoring of the Mellanox BlueField driver
- we prefer async probe in the i801 driver now
- the rest is usual driver updates (support for more SoCs, some
refactoring, some feature additions)
* tag 'i2c-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
i2c: pci1xxxx: prevent signed integer overflow
i2c: acpi: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
i2c: i801: Prefer async probe
i2c: designware-pci: Use standard pattern for memory allocation
i2c: designware-pci: Group AMD NAVI quirk parts together
i2c: microchip: pci1xxxx: Add driver for I2C host controller in multifunction endpoint of pci1xxxx switch
docs: i2c: slave-interface: return errno when handle I2C_SLAVE_WRITE_REQUESTED
i2c: mlxbf: remove device tree support
i2c: mlxbf: support BlueField-3 SoC
i2c: cadence: Add standard bus recovery support
i2c: mlxbf: add multi slave functionality
i2c: mlxbf: support lock mechanism
macintosh/ams: Adapt declaration of ams_i2c_remove() to earlier change
i2c: riic: Use devm_platform_ioremap_resource()
i2c: mlxbf: remove IRQF_ONESHOT
dt-bindings: i2c: rockchip: add rockchip,rk3128-i2c
dt-bindings: i2c: renesas,rcar-i2c: Add r8a779g0 support
i2c: tegra: Add GPCDMA support
i2c: scmi: Convert to be a platform driver
i2c: rk3x: Add rv1126 support
...
Add support for configuring the max SDU per priority and per port. If not
specified, keep the default.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The following patch will need to make this function also respond to
TC_QUERY_BASE, so make the processing more structured around the
tc_setup_type.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Our current vsc9959_tas_guard_bands_update() algorithm has a limitation
imposed by the hardware design. To avoid packet overruns between one
gate interval and the next (which would add jitter for scheduled traffic
in the next gate), we configure the switch to use guard bands. These are
as large as the largest packet which is possible to be transmitted.
The problem is that at tc-taprio intervals of sizes comparable to a
guard band, there isn't an obvious place in which to split the interval
between the useful portion (for scheduling) and the guard band portion
(where scheduling is blocked).
For example, a 10 us interval at 1Gbps allows 1225 octets to be
transmitted. We currently split the interval between the bare minimum of
33 ns useful time (required to schedule a single packet) and the rest as
guard band.
But 33 ns of useful scheduling time will only allow a single packet to
be sent, be that packet 1200 octets in size, or 60 octets in size. It is
impossible to send 2 60 octets frames in the 10 us window. Except that
if we reduced the guard band (and therefore the maximum allowable SDU
size) to 5 us, the useful time for scheduling is now also 5 us, so more
packets could be scheduled.
The hardware inflexibility of not scheduling according to individual
packet lengths must unfortunately propagate to the user, who needs to
tune the queueMaxSDU values if he wants to fit more small packets into a
10 us interval, rather than one large packet.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Existing felix DSA drivers (vsc9959, vsc9953) are all switches that were
integrated in NXP SoCs, which makes them a bit unusual compared to the
usual Microchip branded Ocelot switches.
To be precise, looking at
Documentation/devicetree/bindings/net/mscc,vsc7514-switch.yaml, one can
see 21 memory regions for the "switch" node, and these correspond to the
"targets" of the switch IP, which are spread throughout the guts of that
SoC's memory space.
In NXP integrations, those targets still exist, but they were condensed
within a single memory region, with no other peripheral in between them,
so it made more sense for the driver to ioremap the entire memory space
of the switch, and then find the targets within that memory space via
some offsets hardcoded in the driver.
The effect of this design decision is that now, the felix driver expects
hardware instantiations to provide their own resource definitions, which
is kind of odd when considering a typical device (those are retrieved
from 'reg' properties in the device tree, using platform_get_resource()
or similar).
Allow other hardware instantiations that share the felix driver to not
provide a hardcoded array of resources in the future. Instead, make the
common denominator based on which regmaps are created be just the
resource "names". Each instantiation comes with its own array of names
that are mandatory for it, and with an optional array of resources.
So we split the resources in 2 arrays, one is what's requested and the
other is what's provided. There is one pool of provided resources, in
felix->info->resources (of length felix->info->num_resources). There are
2 different ways of requesting a resource. One is by enum ocelot_target
(this handles the global regmaps), and one is by int port (this handles
the per-port ones).
For the existing vsc9959 and vsc9953, it would be a bit stupid to
request something that's not provided, given that the 2 arrays are both
defined in the same place.
The advantage is that we can now modify felix_request_regmap_by_name()
to make felix->info->resources[] optional, and if absent, the
implementation can call dev_get_regmap() and this is something that is
compatible with MFD.
Co-developed-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use less verbose resource definitions in vsc9959 and vsc9953. This also
sets IORESOURCE_MEM in the constant array of resources, so we don't have
to do this from felix_init_structs() - in fact, in the future, we may
even support IORESOURCE_REG resources.
Note that this macro takes start and length as argument, and we had
start and end before. So transform end into length.
While at it, sort the resources according to their offset.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It turns out that the idea of having a customizable implementation of a
regmap creation from a resource is not exactly useful. The idea was for
the new MFD-based VSC7512 driver to use something that creates a SPI
regmap from a resource. But there are problems in actually getting those
resources (it involves getting them from MFD).
To avoid all that, we'll be getting resources by name, so this custom
init_regmap() method won't be needed. Remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This address is only relevant for the vsc9959, which is a PCIe device
that holds its switch registers in a different PCIe BAR compared to the
registers for the internal MDIO controller.
Hide this aspect from the common felix driver and move the
pci_resource_start() call to the only place that needs it, which is in
vsc9959_mdio_bus_alloc().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The imdio_res is used only by vsc9959, which references its own
vsc9959_imdio_res through the common felix_info->imdio_res pointer.
Since the common code doesn't care about this resource (and it can't be
part of the common array of resources, either, because it belongs in a
different PCI BAR), just reference it directly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary i2c_set_clientdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary i2c_set_clientdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary i2c_set_clientdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The global port interrupt routines and individual ports interrupt
routines has similar implementation except the mask & status register
and number of nested irqs in them. The mask & status register and
pointer to ksz_device is added to ksz_irq and uses the ksz_irq as
irq_chip_data.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To support the phy link detection through interrupt method for ksz9477
based switch, the interrupt handling routines are moved from
lan937x_main.c to ksz_common.c. The only changes made are functions
names are prefixed with ksz_ instead of lan937x_.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, if the mdio node is not present in the dts file then
lan937x_mdio_register return -ENODEV and entire probing process fails.
To make the mdio_register generic for all ksz series switches and to
maintain back-compatibility with existing dts file, return -ENODEV is
replaced with return 0.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the lan937x_mdio_register function, phy interrupts are enabled
irrespective of irq is enabled in the switch. Now, the check is added to
enable the phy interrupt only if the irq is enabled in the switch.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the number of port irqs is hard coded for the lan937x switch
as 6. In order to make the generic interrupt handler for ksz switches,
number of port irq supported by the switch is added to the
ksz_chip_data. It is 4 for ksz9477, 2 for ksz9897 and 3 for ksz9567.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The datasheet [1] explicit describes it as requirement for a reset.
[1] MT7531 Reference Manual for Development Board rev 1.0, page 735
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the PLL init of the switch out of the pad configuration of the port
6 (usally cpu port).
Fix a unidirectional 100 mbit limitation on 1 gbit or 2.5 gbit links for
outbound traffic on port 5 or port 6.
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Read link status from SGMII PCS for in-band managed 2500Base-X and
1000Base-X connection on a MAC port of the MT7531. This is needed to
get the SFP cage working which is connected to SGMII interface of
port 5 of the MT7531 switch IC on the Bananapi BPi-R3 board.
While at it also handle an_complete for both the autoneg and the
non-autoneg codepath.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary spi_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary platform_set_drvdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary platform_set_drvdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary platform_set_drvdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary platform_set_drvdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dev_err() can be replace with dev_err_probe() which will check if error
code is -EPROBE_DEFER.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maximum frame length check is enabled in lan937x switch on POR, But it
is found to be disabled on driver during port setup operation. Due to
this, packets are not dropped when transmitted with greater than configured
value. For testing, setup made for lan1->lan2 transmission and configured
lan1 interface with a frame length (less than 1500 as mentioned in
documentation) and transmitted packets with greater than configured value.
Expected no packets at lan2 end, but packets observed at lan2.
Based on the documentation, packets should get discarded if the actual
packet length doesn't match the frame length configured. Frame length check
should be disabled only for cascaded ports due to tailtags.
This feature was disabled on ksz9477 series due to ptp issue, which is
not in lan937x series. But since lan937x took ksz9477 as base, frame
length check disabled here as well. Patch added to remove this portion
from port setup so that maximum frame length check will be active for
normal ports.
Fixes: 55ab6ffaf3 ("net: dsa: microchip: add DSA support for microchip LAN937x")
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Link: https://lore.kernel.org/r/20220912051228.1306074-1-rakesh.sankaranarayanan@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Changing the DSA master means different things depending on the tagging
protocol in use.
For NPI mode ("ocelot" and "seville"), there is a single port which can
be configured as NPI, but DSA only permits changing the CPU port
affinity of user ports one by one. So changing a user port to a
different NPI port globally changes what the NPI port is, and breaks the
user ports still using the old one.
To address this while still permitting the change of the NPI port,
require that the user ports which are still affine to the old NPI port
are down, and cannot be brought up until they are all affine to the same
NPI port.
The tag_8021q mode ("ocelot-8021q") is more flexible, in that each user
port can be freely assigned to one CPU port or to the other. This works
by filtering host addresses towards both tag_8021q CPU ports, and then
restricting the forwarding from a certain user port only to one of the
two tag_8021q CPU ports.
Additionally, the 2 tag_8021q CPU ports can be placed in a LAG. This
works by enabling forwarding via PGID_SRC from a certain user port
towards the logical port ID containing both tag_8021q CPU ports, but
then restricting forwarding per packet, via the LAG hash codes in
PGID_AGGR, to either one or the other.
When we change the DSA master to a LAG device, DSA guarantees us that
the LAG has at least one lower interface as a physical DSA master.
But DSA masters can come and go as lowers of that LAG, and
ds->ops->port_change_master() will not get called, because the DSA
master is still the same (the LAG). So we need to hook into the
ds->ops->port_lag_{join,leave} calls on the CPU ports and update the
logical port ID of the LAG that user ports are assigned to.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Drivers could refuse to offload a LAG configuration for a variety of
reasons, mainly having to do with its TX type. Additionally, since DSA
masters may now also be LAG interfaces, and this will translate into a
call to port_lag_join on the CPU ports, there may be extra restrictions
there. Propagate the netlink extack to this DSA method in order for
drivers to give a meaningful error message back to the user.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There is a desire to support for DSA masters in a LAG.
That configuration is intended to work by simply enslaving the master to
a bonding/team device. But the physical DSA master (the LAG slave) still
has a dev->dsa_ptr, and that cpu_dp still corresponds to the physical
CPU port.
However, we would like to be able to retrieve the LAG that's the upper
of the physical DSA master. In preparation for that, introduce a helper
called dsa_port_get_master() that replaces all occurrences of the
dp->cpu_dp->master pattern. The distinction between LAG and non-LAG will
be made later within the helper itself.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This node pointer is returned by of_find_compatible_node() with
refcount incremented in this function. of_node_put() on it before
exitting this function.
Fixes: c9cd961c0d ("net: dsa: microchip: lan937x: add interrupt support for port phy link")
Signed-off-by: Sun Ke <sunke32@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220908040226.871690-1-sunke32@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KSZ9477 has the 11 bit ageing count value which is split across the two
registers. And LAN937x has the 20 bit ageing count which is also split
into two registers. Each count in the registers represents 1 second.
This patch add the support for ageing time for KSZ9477 and LAN937x
series of switch.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All switch families supported by the ocelot lib (ocelot, felix, seville)
export the same registers so far. But for example felix also has TSN
counters, while the others don't.
To reduce the bloat even further, create an OCELOT_COMMON_STATS() macro
which just lists all stats that are common between switches. The array
elements are still replicated among all of vsc9959_stats_layout,
vsc9953_stats_layout and ocelot_stats_layout.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current definition of struct ocelot_stat_layout is long-winded (4
lines per entry, and we have hundreds of entries), so we could make an
effort to use the C preprocessor and reduce the line count.
Create an implicit correspondence between enum ocelot_reg, which tells
us the register address (SYS_COUNT_RX_OCTETS etc) and enum ocelot_stat
which allows us to index the ocelot->stats array (OCELOT_STAT_RX_OCTETS
etc), and don't require us to specify both when we define what stats
each switch family has.
Create an OCELOT_STAT() macro that pairs only an enum ocelot_stat to an
enum ocelot_reg, and an OCELOT_STAT_ETHTOOL() macro which also contains
a name exported to the unstructured ethtool -S stringset API. For now,
we define all counters as having the OCELOT_STAT_ETHTOOL() kind, but we
will add more counters in the future which are not exported to the
unstructured ethtool -S.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware counter is called C_TX_AGED, so rename SYS_COUNT_TX_AGING
to SYS_COUNT_TX_AGED. This will become important since we want to
minimize the way in which we declare struct ocelot_stat_layout elements,
using the C preprocessor.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA is integrated with the new standardized ethtool -S --groups option,
but the felix driver only exports unstructured statistics.
Reuse the array of 64-bit statistics collected by ocelot_check_stats_work(),
but just export select values from it.
Since ocelot_check_stats_work() runs periodically to avoid 32-bit
overflow, and the ethtool calling context is sleepable, we update the
64-bit stats one more time, to provide up-to-date values. The locking
scheme with a mutex followed by a spinlock is a bit hard to digest, so
we create and use a ocelot_port_stats_run() helper with a callback that
populates the ethool stats group the caller is interested in.
The exported stats are:
ethtool -S swp0 --groups eth-phy
ethtool -S swp0 --groups eth-mac
ethtool -S swp0 --groups eth-ctrl
ethtool -S swp0 --groups rmon
ethtool --include-statistics --show-pause swp0
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the logic from the ocelot switchdev driver's ocelot_get_stats64()
method to the common switch lib and reuse it for the DSA driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix PSFP counters suffer from the same problem as the ocelot
ndo_get_stats64 ones - they are 32-bit, so they can easily overflow and
this can easily go undetected.
Add a custom hook in ocelot_check_stats_work() through which driver
specific actions can be taken, and update the stats for the existing
PSFP filters from that hook.
Previously, vsc9959_psfp_filter_add() and vsc9959_psfp_filter_del() were
serialized with respect to each other via rtnl_lock(). However, with the
new entry point into &psfp->sfi_list coming from the periodic worker, we
now need an explicit mutex to serialize access to these lists.
We used to keep a struct felix_stream_filter_counters on stack, through
which vsc9959_psfp_stats_get() - a FLOW_CLS_STATS callback - would
retrieve data from vsc9959_psfp_counters_get(). We need to become
smarter about that in 3 ways:
- we need to keep a persistent set of counters for each stream instead
of keeping them on stack
- we need to promote those counters from u32 to u64, and create a
procedure that properly keeps 64-bit counters. Since we clear the
hardware counters anyway, and we poll every 2 seconds, a simple
increment of a u64 counter with a u32 value will perfectly do the job.
- FLOW_CLS_STATS also expect incremental counters, so we also need to
zeroize our u64 counters every time sch_flower calls us
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support SPI-controlled switches in the future, access to
SYS_STAT_CFG_STAT_VIEW needs to be done outside of any spinlock
protected region, but it still needs to be serialized (by a mutex).
Split the ocelot->stats_lock spinlock into a mutex that serializes
indirect access to hardware registers (ocelot->stat_view_lock) and a
spinlock that serializes access to the u64 ocelot->stats array.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSN stream (802.1Qci, 802.1CB) filters are also accessed through
STAT_VIEW, just like the port registers, but these counters are per
stream, rather than per port. So we don't keep them in
ocelot_port_update_stats().
What we can do, however, is we can create register definitions for them
just like we have for the port counters, and delete the last remaining
user of the SYS_CNT register + a group index (read_gix).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The read-modify-write of QSYS_TAG_CONFIG from vsc9959_sched_speed_set()
runs unlocked with respect to the other functions that access it, which
are vsc9959_tas_guard_bands_update(), vsc9959_qos_port_tas_set() and
vsc9959_tas_clock_adjust(). All the others are under ocelot->tas_lock,
so move the vsc9959_sched_speed_set() access under that lock as well, to
resolve the concurrency.
Fixes: 55a515b1f5 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Experimentally, it looks like when QSYS_QMAXSDU_CFG_7 is set to 605,
frames even way larger than 601 octets are transmitted even though these
should be considered as oversized, according to the documentation, and
dropped.
Since oversized frame dropping depends on frame size, which is only
known at the EOF stage, and therefore not at SOF when cut-through
forwarding begins, it means that the switch cannot take QSYS_QMAXSDU_CFG_*
into consideration for traffic classes that are cut-through.
Since cut-through forwarding has no UAPI to control it, and the driver
enables it based on the mantra "if we can, then why not", the strategy
is to alter vsc9959_cut_through_fwd() to take into consideration which
tc's have oversize frame dropping enabled, and disable cut-through for
them. Then, from vsc9959_tas_guard_bands_update(), we re-trigger the
cut-through determination process.
There are 2 strategies for vsc9959_cut_through_fwd() to determine
whether a tc has oversized dropping enabled or not. One is to keep a bit
mask of traffic classes per port, and the other is to read back from the
hardware registers (a non-zero value of QSYS_QMAXSDU_CFG_* means the
feature is enabled). We choose reading back from registers, because
struct ocelot_port is shared with drivers (ocelot, seville) that don't
support either cut-through nor tc-taprio, and we don't have a felix
specific extension of struct ocelot_port. Furthermore, reading registers
from the Felix hardware is quite cheap, since they are memory-mapped.
Fixes: 55a515b1f5 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit broke tc-taprio schedules such as this one:
tc qdisc replace dev $swp1 root taprio \
num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0 \
sched-entry S 0x7f 990000 \
sched-entry S 0x80 10000 \
flags 0x2
because the gate entry for TC 7 (S 0x80 10000 ns) now has a static guard
band added earlier than its 'gate close' event, such that packet
overruns won't occur in the worst case of the largest packet possible.
Since guard bands are statically determined based on the per-tc
QSYS_QMAXSDU_CFG_* with a fallback on the port-based QSYS_PORT_MAX_SDU,
we need to discuss what happens with TC 7 depending on kernel version,
since the driver, prior to commit 55a515b1f5 ("net: dsa: felix: drop
oversized frames with tc-taprio instead of hanging the port"), did not
touch QSYS_QMAXSDU_CFG_*, and therefore relied on QSYS_PORT_MAX_SDU.
1 (before vsc9959_tas_guard_bands_update): QSYS_PORT_MAX_SDU defaults to
1518, and at gigabit this introduces a static guard band (independent
of packet sizes) of 12144 ns, plus QSYS::HSCH_MISC_CFG.FRM_ADJ (bit
time of 20 octets => 160 ns). But this is larger than the time window
itself, of 10000 ns. So, the queue system never considers a frame with
TC 7 as eligible for transmission, since the gate practically never
opens, and these frames are forever stuck in the TX queues and hang
the port.
2 (after vsc9959_tas_guard_bands_update): Under the sole goal of
enabling oversized frame dropping, we make an effort to set
QSYS_QMAXSDU_CFG_7 to 1230 bytes. But QSYS_QMAXSDU_CFG_7 plays
one more role, which we did not take into account: per-tc static guard
band, expressed in L2 byte time (auto-adjusted for FCS and L1 overhead).
There is a discrepancy between what the driver thinks (that there is
no guard band, and 100% of min_gate_len[tc] is available for egress
scheduling) and what the hardware actually does (crops the equivalent
of QSYS_QMAXSDU_CFG_7 ns out of min_gate_len[tc]). In practice, this
means that the hardware thinks it has exactly 0 ns for scheduling tc 7.
In both cases, even minimum sized Ethernet frames are stuck on egress
rather than being considered for scheduling on TC 7, even if they would
fit given a proper configuration. Considering the current situation,
with vsc9959_tas_guard_bands_update(), frames between 60 octets and 1230
octets in size are not eligible for oversized dropping (because they are
smaller than QSYS_QMAXSDU_CFG_7), but won't be considered as eligible
for scheduling either, because the min_gate_len[7] (10000 ns) minus the
guard band determined by QSYS_QMAXSDU_CFG_7 (1230 octets * 8 ns per
octet == 9840 ns) minus the guard band auto-added for L1 overhead by
QSYS::HSCH_MISC_CFG.FRM_ADJ (20 octets * 8 ns per octet == 160 octets)
leaves 0 ns for scheduling in the queue system proper.
Investigating the hardware behavior, it becomes apparent that the queue
system needs precisely 33 ns of 'gate open' time in order to consider a
frame as eligible for scheduling to a tc. So the solution to this
problem is to amend vsc9959_tas_guard_bands_update(), by giving the
per-tc guard bands less space by exactly 33 ns, just enough for one
frame to be scheduled in that interval. This allows the queue system to
make forward progress for that port-tc, and prevents it from hanging.
Fixes: 297c4de6f7 ("net: dsa: felix: re-enable TAS guard band mode")
Reported-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for the LAN9354 device by allowing it to use
the LAN9303 DSA driver. These devices have the same underlying
access and control methods and from a feature set point of view
the LAN9354 is a superset of the LAN9303.
The MDIO access method has been tested on a SAMA5D3-EDS board
with a LAN9354 RMII daughter card.
While the SPI access method should also be the same, it has not
been tested and as such is not included at this time.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial BYTE_ORDER read to sync the 32-bit accesses over the 16-bit
mdio bus to improve driver robustness.
The lan9303 expects two mdio read transactions back-to-back to read a
32-bit register. The first read transaction causes the other half of the
32-bit register to get latched. The subsequent read returns the latched
second half of the 32-bit read. The BYTE_ORDER register is an exception to
this rule. As it is a constant value, there is no need to latch the second
half. We read this register first in case there were reads during the boot
loader process that might have occurred prior to this driver taking over
ownership of accessing this device.
This patch has been tested on the SAMA5D3-EDS with a LAN9303 RMII daughter
card.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the KSZ9477S datasheet, there is no global register
at 0x033C and 0x033D addresses.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the KSZ9896 6-port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9896 supports both SPI (already in) and I2C.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the KSZ9896 6-port Gigabit Ethernet Switch to the
ksz9477 driver.
Although the KSZ9896 is already listed in the device tree binding
documentation since a1c0ed24fe (dt-bindings: net: dsa: document
additional Microchip KSZ9477 family switches) the chip id
(0x00989600) is not recognized by ksz_switch_detect() and rejected
by the driver.
The KSZ9896 is similar to KSZ9897 but has only one configurable
MII/RMII/RGMII/GMII cpu port.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_get_match_data is called on priv->dev before priv->dev is
actually set. Move of_device_get_match_data after priv->dev is correctly
set to fix this kernel panic.
Fixes: 3bb0844e7b ("net: dsa: qca8k: cache match data to speed up access")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220904215319.13070-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch enables the interrupts for internal phy link detection for
LAN937x. The interrupt enable bits are active low. There is global
interrupt mask for each port. And each port has the individual interrupt
mask for TAS. QCI, SGMII, PTP, PHY and ACL.
The first level of interrupt domain is registered for global port
interrupt and second level of interrupt domain for the individual port
interrupts. The phy interrupt is enabled in the lan937x_mdio_register
function. Interrupt from which port is raised will be detected based on
the interrupt host data.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the lan937x_reset_switch(), it masks all the switch and port
registers. In the Global_Int_status register, POR ready bit is write 1
to clear bit and all other bits are read only. So, this patch clear the
por_ready_int status bit by writing 1.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct ksz_port doesn't have reference to ksz_device as of now. In order
to find out from which port interrupt has triggered, we need to pass the
struct ksz_port as a host data. When the interrupt is triggered, we can
get the port from which interrupt triggered, but to identify it is phy
interrupt we have to read status register. The regmap structure for
accessing the device register is present in the ksz_device struct. To
access the ksz_device from the ksz_port, the reference is added to it
with port number as well.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After driver refactoring we was running ksz9477 specific CPU port
configuration on ksz8 family which ended with kernel oops. So, make sure
we run this code only on ksz9477 compatible devices.
Tested on KSZ8873 and KSZ9477.
Fixes: da8cd08520 ("net: dsa: microchip: add support for common phylink mac link up")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use chip_id as other places of this code do it
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is not used. So, remove it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is not used on ksz9477 side. Remove it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is unused. So, drop it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With code refactoring was introduced new variable internal_phy. Let's
use it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add register validation for KSZ9477
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason why PHYlib may access MII_CTRL1000 on the chip without GBit
support is only if chip provides wrong information about extended caps
register. This issue is now handled by ksz9477_r_phy_quirks()
With proper regmap_ranges provided for all chips we will be able to
catch this kind of bugs any way. So, remove this sanity check.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add register validation for KSZ8563.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is complex driver with support for different chips with different
layouts. To detect at least some bugs earlier, we should validate register
accesses by using regmap_access_table support.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was detected after adding regmap register access validation.
KSZ9893 compatible chips do not have "Output Clock Control Register
0x0103". So, avoid writing to it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now ksz_pread/ksz_pwrite can return error value. So, make use of it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now ksz_pread/ksz_pwrite can return error value. So, make use of it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz_read*/ksz_write* are able to return errors, so forward it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY access may end with errors on different levels. So, allow to forward
return values where possible.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was detected after adding support of regmap_ranges for KSZ8563R
chip. This chip is reporting extended registers support without having
actual extended registers. This made PHYlib request not existing
registers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ8563 has two 100Mbit PHYs and CPU port with RGMII support. Since
1000Mbit configuration for the RGMII capable MAC is present, we should
use per port validation.
As main part of migration to per-port validation we need to rework
ksz9477_switch_init() function. Which is using undocumented
REG_GLOBAL_OPTIONS register to detect per-chip Gbit support. So, it is
related to some sort of risk for regressions.
To reduce this risk I compared the code with publicly available
documentations. This function will executed on following currently
supported chips:
struct ksz_chip_data OF compatible
KSZ9477 KSZ9477
KSZ9897 KSZ9897
KSZ9893 KSZ9893, KSZ9563
KSZ8563 KSZ8563
KSZ9567 KSZ9567
Only KSZ9893, KSZ9563, KSZ8563 document existence of 0xf ==
REG_GLOBAL_OPTIONS register with bit field description "SKU ID":
KSZ9893 0x0C
KSZ9563 0x1C
KSZ8563 0x3C
The existence of hidden flags is not documented.
KSZ9477, KSZ9897, KSZ9567 do not document this register at all.
Only KSZ8563 is documented as non Gbit chip: 100Mbit PHYs and RGMII CPU
port. So, this change should not introduce a regression for
configurations with properly used OF compatibles.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add separate entry for the KSZ8563 chip. According to the documentation
it can support Gbit only on RGMII port. So, we will need to be able to
describe in the followup patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xrs700x_read_port_counters() updates the stats from a worker using the
u64_stats_update_begin() version. This is okay on 32-UP since on the
reader side preemption is disabled.
On 32bit-SMP the writer can be preempted by the reader at which point
the reader will spin on the seqcount until writer continues and
completes the update.
Assigning the mib_mutex mutex to the underlying seqcount would ensure
proper synchronisation. The API for that on the u64_stats_init() side
isn't available. Since it is the only user, just use disable interrupts
during the update.
Use u64_stats_update_begin_irqsave() on the writer side to ensure an
uninterrupted update.
Fixes: ee00b24f32 ("net: dsa: add Arrow SpeedChips XRS700x driver")
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
p0_mode set to one of the supported serial mode should not prevent
configuring the external SMI interface in
mv88e6xxx_g2_scratch_gpio_set_smi. The current masking of the p0_mode
only checks the first 2 bits. This results in switches supporting
serial mode cannot setup external SMI on certain serial modes
(Ex: 1000BASE-X and SGMII).
Extend the mask of the p0_mode to include the reduced modes and
serial modes as allowed modes for the external SMI interface.
Signed-off-by: Marcus Carlberg <marcus.carlberg@axis.com>
Link: https://lore.kernel.org/r/20220824093706.19049-1-marcus.carlberg@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the probe defaults all interfaces to the highest speed possible
(10GBASE-X in mv88e6393x) before the phy mode configuration from the
devicetree is considered it is currently impossible to use port 0 in
RGMII mode.
This change will allow RGMII modes to be configurable for port 0
enabling port 0 to be configured as RGMII as well as serial depending
on configuration.
Signed-off-by: Marcus Carlberg <marcus.carlberg@axis.com>
Link: https://lore.kernel.org/r/20220822144136.16627-1-marcus.carlberg@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Address learning should initially be turned off by the driver for port
operation in standalone mode, then the DSA core handles changes to it
via ds->ops->port_bridge_flags().
Leaving address learning enabled while ports are standalone breaks any
kind of communication which involves port B receiving what port A has
sent. Notably it breaks the ksz9477 driver used with a (non offloaded,
ports act as if standalone) bonding interface in active-backup mode,
when the ports are connected together through external switches, for
redundancy purposes.
This fixes a major design flaw in the ksz9477 and ksz8795 drivers, which
unconditionally leave address learning enabled even while ports operate
as standalone.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Link: https://lore.kernel.org/netdev/CAFZh4h-JVWt80CrQWkFji7tZJahMfOToUJQgKS5s0_=9zzpvYQ@mail.gmail.com/
Reported-by: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220818164809.3198039-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a partial revert of commit c295f9831f ("net: mscc: ocelot:
switch from {,un}set to {,un}assign for tag_8021q CPU ports"), because
as it turns out, this isn't how tag_8021q CPU ports under a LAG are
supposed to work.
Under that scenario, all user ports are "assigned" to the single
tag_8021q CPU port represented by the logical port corresponding to the
bonding interface. So one CPU port in a LAG would have is_dsa_8021q_cpu
set to true (the one whose physical port ID is equal to the logical port
ID), and the other one to false.
In turn, this makes 2 undesirable things happen:
(1) PGID_CPU contains only the first physical CPU port, rather than both
(2) only the first CPU port will be added to the private VLANs used by
ocelot for VLAN-unaware bridging
To make the driver behave in the same way for both bonded CPU ports, we
need to bring back the old concept of setting up a port as a tag_8021q
CPU port, and this is what deals with VLAN membership and PGID_CPU
updating. But we also need the CPU port "assignment" (the user to CPU
port affinity), and this is what updates the PGID_SRC forwarding rules.
All DSA CPU ports are statically configured for tag_8021q mode when the
tagging protocol is changed to ocelot-8021q. User ports are "assigned"
to one CPU port or the other dynamically (this will be handled by a
future change).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
DSA has multiple ways of specifying a MAC connection to an internal PHY.
One requires a DT description like this:
port@0 {
reg = <0>;
phy-handle = <&internal_phy>;
phy-mode = "internal";
};
(which is IMO the recommended approach, as it is the clearest
description)
but it is also possible to leave the specification as just:
port@0 {
reg = <0>;
}
and if the driver implements ds->ops->phy_read and ds->ops->phy_write,
the DSA framework "knows" it should create a ds->slave_mii_bus, and it
should connect to a non-OF-based internal PHY on this MDIO bus, at an
MDIO address equal to the port address.
There is also an intermediary way of describing things:
port@0 {
reg = <0>;
phy-handle = <&internal_phy>;
};
In case 2, DSA calls phylink_connect_phy() and in case 3, it calls
phylink_of_phy_connect(). In both cases, phylink_create() has been
called with a phy_interface_t of PHY_INTERFACE_MODE_NA, and in both
cases, PHY_INTERFACE_MODE_NA is translated into phy->interface.
It is important to note that phy_device_create() initializes
dev->interface = PHY_INTERFACE_MODE_GMII, and so, when we use
phylink_create(PHY_INTERFACE_MODE_NA), no one will override this, and we
will end up with a PHY_INTERFACE_MODE_GMII interface inherited from the
PHY.
All this means that in order to maintain compatibility with device tree
blobs where the phy-mode property is missing, we need to allow the
"gmii" phy-mode and treat it as "internal".
Fixes: 2c709e0bda ("net: dsa: microchip: ksz8795: add phylink support")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216320
Reported-by: Craig McQueen <craig@mcqueen.id.au>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20220818143250.2797111-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With so many counter addresses recently discovered as being wrong, it is
desirable to at least have a central database of information, rather
than two: one through the SYS_COUNT_* registers (used for
ndo_get_stats64), and the other through the offset field of struct
ocelot_stat_layout elements (used for ethtool -S).
The strategy will be to keep the SYS_COUNT_* definitions as the single
source of truth, but for that we need to expand our current definitions
to cover all registers. Then we need to convert the ocelot region
creation logic, and stats worker, to the read semantics imposed by going
through SYS_COUNT_* absolute register addresses, rather than offsets
of 32-bit words relative to SYS_COUNT_RX_OCTETS (which should have been
SYS_CNT, by the way).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ocelot counters are 32-bit and require periodic reading, every 2
seconds, by ocelot_port_update_stats(), so that wraparounds are
detected.
Currently, the counters reported by ocelot_get_stats64() come from the
32-bit hardware counters directly, rather than from the 64-bit
accumulated ocelot->stats, and this is a problem for their integrity.
The strategy is to make ocelot_get_stats64() able to cherry-pick
individual stats from ocelot->stats the way in which it currently reads
them out from SYS_COUNT_* registers. But currently it can't, because
ocelot->stats is an opaque u64 array that's used only to feed data into
ethtool -S.
To solve that problem, we need to make ocelot->stats indexable, and
associate each element with an element of struct ocelot_stat_layout used
by ethtool -S.
This makes ocelot_stat_layout a fat (and possibly sparse) array, so we
need to change the way in which we access it. We no longer need
OCELOT_STAT_END as a sentinel, because we know the array's size
(OCELOT_NUM_STATS). We just need to skip the array elements that were
left unpopulated for the switch revision (ocelot, felix, seville).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ocelot_get_stats64() currently runs unlocked and therefore may collide
with ocelot_port_update_stats() which indirectly accesses the same
counters. However, ocelot_get_stats64() runs in atomic context, and we
cannot simply take the sleepable ocelot->stats_lock mutex. We need to
convert it to an atomic spinlock first. Do that as a preparatory change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reading stats using the SYS_COUNT_* register definitions is only used by
ocelot_get_stats64() from the ocelot switchdev driver, however,
currently the bucket definitions are incorrect.
Separately, on both RX and TX, we have the following problems:
- a 256-1023 bucket which actually tracks the 256-511 packets
- the 1024-1526 bucket actually tracks the 512-1023 packets
- the 1527-max bucket actually tracks the 1024-1526 packets
=> nobody tracks the packets from the real 1527-max bucket
Additionally, the RX_PAUSE, RX_CONTROL, RX_LONGS and RX_CLASSIFIED_DROPS
all track the wrong thing. However this doesn't seem to have any
consequence, since ocelot_get_stats64() doesn't use these.
Even though this problem only manifests itself for the switchdev driver,
we cannot split the fix for ocelot and for DSA, since it requires fixing
the bucket definitions from enum ocelot_reg, which makes us necessarily
adapt the structures from felix and seville as well.
Fixes: 84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953 switch")
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
What the driver actually reports as 256-511 is in fact 512-1023, and the
TX packets in the 256-511 bucket are not reported. Fix that.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If an error occurs in dsa_devlink_region_create(), then 'priv->regions'
array will be accessed by negative index '-1'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rustam Subkhankulov <subkhankulov@ispras.ru>
Fixes: bf425b8205 ("net: dsa: sja1105: expose static config as devlink region")
Link: https://lore.kernel.org/r/20220817003845.389644-1-subkhankulov@ispras.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the ksz9477_fdb_dump function it reads the ALU control register and
exit from the timeout loop if there is valid entry or search is
complete. After exiting the loop, it reads the alu entry and report to
the user space irrespective of entry is valid. It works till the valid
entry. If the loop exited when search is complete, it reads the alu
table. The table returns all ones and it is reported to user space. So
bridge fdb show gives ff:ff:ff:ff:ff:ff as last entry for every port.
To fix it, after exiting the loop the entry is reported only if it is
valid one.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220816105516.18350-1-arun.ramadoss@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the artificial limitations imposed upon
bcm_sf2_sw_mac_link_{up,down} and allow us to override the link
parameters for IMP port(s) as well as regular ports by accounting for
the special differences that exist there.
Remove the code that did override the link parameters in
bcm_sf2_imp_setup().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Depending upon the generation of switches, we have different offsets for
configuring a given port's status override where link parameters are
applied. Introduce a helper function that we re-use throughout the code
in order to let phylink callbacks configure the IMP/CPU port(s) in
subsequent changes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If the port isn't a CPU port nor a user port, 'cpu_dp'
is a null pointer and a crash happened on dereferencing
it in mv88e6060_setup_port():
[ 9.575872] Unable to handle kernel NULL pointer dereference at virtual address 00000014
...
[ 9.942216] mv88e6060_setup from dsa_register_switch+0x814/0xe84
[ 9.948616] dsa_register_switch from mdio_probe+0x2c/0x54
[ 9.954433] mdio_probe from really_probe.part.0+0x98/0x2a0
[ 9.960375] really_probe.part.0 from driver_probe_device+0x30/0x10c
[ 9.967029] driver_probe_device from __device_attach_driver+0xb8/0x13c
[ 9.973946] __device_attach_driver from bus_for_each_drv+0x90/0xe0
[ 9.980509] bus_for_each_drv from __device_attach+0x110/0x184
[ 9.986632] __device_attach from bus_probe_device+0x8c/0x94
[ 9.992577] bus_probe_device from deferred_probe_work_func+0x78/0xa8
[ 9.999311] deferred_probe_work_func from process_one_work+0x290/0x73c
[ 10.006292] process_one_work from worker_thread+0x30/0x4b8
[ 10.012155] worker_thread from kthread+0xd4/0x10c
[ 10.017238] kthread from ret_from_fork+0x14/0x3c
Fixes: 0abfd494de ("net: dsa: use dedicated CPU port")
CC: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220811070939.1717146-1-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The way in which dsa_tree_change_tag_proto() works is that when
dsa_tree_notify() fails, it doesn't know whether the operation failed
mid way in a multi-switch tree, or it failed for a single-switch tree.
So even though drivers need to fail cleanly in
ds->ops->change_tag_protocol(), DSA will still call dsa_tree_notify()
again, to restore the old tag protocol for potential switches in the
tree where the change did succeeed (before failing for others).
This means for the felix driver that if we report an error in
felix_change_tag_protocol(), we'll get another call where proto_ops ==
old_proto_ops. If we proceed to act upon that, we may do unexpected
things. For example, we will call dsa_tag_8021q_register() twice in a
row, without any dsa_tag_8021q_unregister() in between. Then we will
actually call dsa_tag_8021q_unregister() via old_proto_ops->teardown,
which (if it manages to run at all, after walking through corrupted data
structures) will leave the ports inoperational anyway.
The bug can be readily reproduced if we force an error while in
tag_8021q mode; this crashes the kernel.
echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging
echo edsa > /sys/class/net/eno2/dsa/tagging # -EPROTONOSUPPORT
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000014
Call trace:
vcap_entry_get+0x24/0x124
ocelot_vcap_filter_del+0x198/0x270
felix_tag_8021q_vlan_del+0xd4/0x21c
dsa_switch_tag_8021q_vlan_del+0x168/0x2cc
dsa_switch_event+0x68/0x1170
dsa_tree_notify+0x14/0x34
dsa_port_tag_8021q_vlan_del+0x84/0x110
dsa_tag_8021q_unregister+0x15c/0x1c0
felix_tag_8021q_teardown+0x16c/0x180
felix_change_tag_protocol+0x1bc/0x230
dsa_switch_event+0x14c/0x1170
dsa_tree_change_tag_proto+0x118/0x1c0
Fixes: 7a29d220f4 ("net: dsa: felix: reimplement tagging protocol change with function pointers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220808125127.3344094-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
min_gate_len[tc] is supposed to track the shortest interval of
continuously open gates for a traffic class. For example, in the
following case:
TC 76543210
t0 00000001b 200000 ns
t1 00000010b 200000 ns
min_gate_len[0] and min_gate_len[1] should be 200000, while
min_gate_len[2-7] should be 0.
However what happens is that min_gate_len[0] is 200000, but
min_gate_len[1] ends up being 0 (despite gate_len[1] being 200000 at the
point where the logic detects the gate close event for TC 1).
The problem is that the code considers a "gate close" event whenever it
sees that there is a 0 for that TC (essentially it's level rather than
edge triggered). By doing that, any time a gate is seen as closed
without having been open prior, gate_len, which is 0, will be written
into min_gate_len. Once min_gate_len becomes 0, it's impossible for it
to track anything higher than that (the length of actually open
intervals).
To fix this, we make the writing to min_gate_len[tc] be edge-triggered,
which avoids writes for gates that are closed in consecutive intervals.
However what this does is it makes us need to special-case the
permanently closed gates at the end.
Fixes: 55a515b1f5 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220804202817.1677572-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same function to read the switch id is used by drivers based on
qca8k family switch. Move them to common code to make them accessible
also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same port LAG functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same port VLAN functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Also drop exposing busy_wait and make it static.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same port mirror functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same port FDB/MDB function are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Also drop bulk read/write functions and make them static
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same set age, MTU and port enable/disable function are used by
driver based on qca8k family switch.
Move them to common code to make them accessible also by other drivers.
While at it also drop unnecessary qca8k_priv cast for void pointers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same bridge functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
While at it also drop unnecessary qca8k_priv cast for void pointers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same logic to disable/enable port, set eee and get ethtool stats is
used by drivers based on qca8k family switch.
Move it to common code to make it accessible also by other drivers.
While at it also drop unnecessary qca8k_priv cast for void pointers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same mib function is used by drivers based on qca8k family switch.
Move it to common code to make it accessible also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same ATU function are used by drivers based on qca8k family switch.
Move the bulk read/write helper to common code to declare these shared
ATU functions in common code.
These helper will be dropped when regmap correctly support bulk
read/write.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same reg table and read/write/rmw function are used by drivers
based on qca8k family switch.
Move them to common code to make it accessible also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same MIB struct is used by drivers based on qca8k family switch. Move
it to common code to make it accessible also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some switch may not support mib autocast feature and require the legacy
way of reading the regs directly.
Make the mib autocast feature optional and permit to declare support for
it using match_data struct in a dedicated qca8k_info_ops struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using of_device_get_match_data is expensive. Cache match data to speed
up access and rework user of match data to use the new cached value.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 3c783b83bd ("net: dsa: mv88e6xxx: get rid of SPEED_MAX setting")
stopped relying on SPEED_MAX constant and hardcoded speed settings
for the switch ports and rely on phylink configuration.
It turned out, however, that when the relevant code is called,
the mac_capabilites of CPU/DSA port remain unset.
mv88e6xxx_setup_port() is called via mv88e6xxx_setup() in
dsa_tree_setup_switches(), which precedes setting the caps in
phylink_get_caps down in the chain of dsa_tree_setup_ports().
As a result the mac_capabilites are 0 and the default speed for CPU/DSA
port is 10M at the start. To fix that, execute mv88e6xxx_get_caps()
and obtain the capabilities driectly.
Fixes: 3c783b83bd ("net: dsa: mv88e6xxx: get rid of SPEED_MAX setting")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220726230918.2772378-1-mw@semihalf.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch add support for phylink mac config for ksz series of
switches. All the files ksz8795, ksz9477 and lan937x uses the ksz common
xmii function. Instead of calling from the individual files, it is moved
to the ksz common phylink mac config function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the ksz8795 cpu configuration to use the ksz common
xmii set functions.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ksz9477.c file, configuring the xmii register is performed based on
the flag NEW_XMII. The flag is reset for ksz9893 switch and set for
other switch. This patch uses the ksz common xmii set and get function.
The bit values are configured based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch read the rgmii tx and rx delay from device tree and stored it
in the ksz_port. It applies the rgmii delay to the xmii tune adjust
register based on the interface selected in phylink mac config. There
are two rgmii port in LAN937x and value to be loaded in the register
vary depends on the port selected.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the common ksz_set_xmii function for ksz series switch
and update the lan937x code phylink mac config. The register address for
the ksz8795 is Port 5 Interface control 6 and for all other switch is
xMII Control 1.
The bit value for selecting the interface is same for
KSZ8795 and KSZ9893 are same. The bit values for KSZ9477 and lan973x are
same. So, this patch add the bit value for each switches in
ksz_chip_data and configure the registers based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for common phylink mac link up for the ksz
series switch. The register address, bit position and values are
configured based on the chip id to the dev->info structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add common function for configuring the Full/Half duplex and
transmit/receive flow control. KSZ8795 uses the Global control register
4 for configuring the duplex and flow control, whereas all other KSZ9477
based switch uses the xMII Control 0 register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the function for configuring the 100/10Mbps speed
selection for the ksz switches. KSZ8795 switch uses Global control 4
register 0x06 bit 4 for choosing 100/10Mpbs. Other switches uses xMII
control 1 0xN300 for it.
For KSZ8795, if the bit is set then 10Mbps is chosen and if bit is
clear then 100Mbps chosen. For all other switches it is other way
around, if the bit is set then 100Mbps is chosen.
So, this patch add the generic function for ksz switch to select the
100/10Mbps speed selection. While configuring, first it disables the
gigabit functionality and then configure the respective speed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add helper function for setting and getting the gigabit
enable for the ksz series switch. KSZ8795 switch has different register
address compared to all other ksz switches. KSZ8795 series uses the Port
5 Interface control 6 Bit 6 for configuring the 1Gbps or 100/10Mbps
speed selection. All other switches uses the xMII control 1 0xN301
register Bit6 for gigabit.
Further, for KSZ8795 & KSZ9893 switches if bit 1 then 1Gbps is chosen
and if bit 0 then 100/10Mbps is chosen. It is other way around for
other switches bit 0 is for 1Gbps. So, this patch implements the common
function for configuring the gigabit set and get capability.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the refactoring for the ksz8_dev_ops from ksz8795.c to
ksz_common.c, the ksz8_r_mib_cnt has been missed. So this patch adds the
missing one.
Fixes: 6ec23aaaac ("net: dsa: microchip: move ksz_dev_ops to ksz_common.c")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220718061803.4939-1-arun.ramadoss@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add spi_device_id entries to silent SPI warnings.
Fixes: 5fa6863ba6 ("spi: Check we have a spi_device_id for each DT compatible")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220717135831.2492844-2-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add spi_device_id entries to silent following warnings:
SPI driver sja1105 has no spi_device_id for nxp,sja1105e
SPI driver sja1105 has no spi_device_id for nxp,sja1105t
SPI driver sja1105 has no spi_device_id for nxp,sja1105p
SPI driver sja1105 has no spi_device_id for nxp,sja1105q
SPI driver sja1105 has no spi_device_id for nxp,sja1105r
SPI driver sja1105 has no spi_device_id for nxp,sja1105s
SPI driver sja1105 has no spi_device_id for nxp,sja1110a
SPI driver sja1105 has no spi_device_id for nxp,sja1110b
SPI driver sja1105 has no spi_device_id for nxp,sja1110c
SPI driver sja1105 has no spi_device_id for nxp,sja1110d
Fixes: 5fa6863ba6 ("spi: Check we have a spi_device_id for each DT compatible")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220717135831.2492844-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch removes the of_match_ptr() pointer when dereferencing the
ksz_dt_ids which produce the unused variable warning.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ksz_switch_register(), we should call of_node_put() for the
reference returned by of_get_child_by_name() which has increased
the refcount.
Fixes: 912aae27c6 ("net: dsa: microchip: really look for phy-mode in port nodes")
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220714153138.375919-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move qca8k driver to qca dir in preparation for code split and
introduction of ipq4019 switch based on qca8k.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary spi_set_drvdata() in b53_spi_remove(), the
driver_data will be set to NULL in device_unbind_cleanup() after
calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220705131733.351962-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
felix_vsc9959.c calls taprio_offload_get() and taprio_offload_free(),
symbols exported by net/sched/sch_taprio.c. As such, we must disallow
building the Felix driver as built-in when the symbol exported by
tc-taprio isn't present in the kernel image.
Fixes: 1c9017e44a ("net: dsa: felix: keep reference on entire tc-taprio config")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220704190241.1288847-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch add the LAN937x part support in the existing ksz_spi_probe.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for phylink_mac_config dsa hook. It configures
the mac for MII/RMII modes. The RGMII mode will be added in the future
patches.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for phylink_mac_link_up. It configures the mac
for the speed, flow control and duplex mode.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal phy of the LAN937x are capable of 100Mbps Full duplex. The
xMII port of switch is capable of 10Mbps Full & Half Duplex, 100Mbps
Full & Half Duplex and 1000Mbps Half duplex. xMII port also supports Tx
and Rx Flow control.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for port_max_mtu, port_change_mtu and
port_fast_age dsa functionality.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch register mdio-bus for the lan937x series switch. mdio read
and write uses the vphy for accessing the phy register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for the writing and reading of the phy registers.
LAN937x uses the Vphy indirect addressing method for accessing the phys.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch update the ksz_get_tag_protocol to return LAN937x specific
tag if the chip id matches one of LAN937x series switch
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic DSA driver support for lan937x and the device will be
configured through SPI interface.
It adds the lan937x_dev_ops in ksz_common.c file and tries to reuse the
functionality of ksz9477 series switch.
drivers/net/dsa/microchip/ path is already part of MAINTAINERS &
the new files come under this path. Hence no update needed to the
MAINTAINERS
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz9477 and lan937x has few difference in the static and reserved
table register 0x041C. For the ksz9477 if the bit 0 is 1 - read
operation and 0 - write operation. But for lan937x bit 1:0 used for
selecting the read/write operation, 01 - write and 10 - read.
To use ksz9477 mdb add/del and enable_stp_addr for the lan937x, masks &
shifts are introduced for ksz9477 & lan937x in ksz_common.c. Then
updated the function with masks & shifts based on the switch instead of
hard coding it.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Time-sensitive networking code needs to work with PTP times expressed in
nanoseconds, and with packet transmission times expressed in
picoseconds, since those would be fractional at higher than gigabit
speed when expressed in nanoseconds.
Convert the existing uses in tc-taprio and the ocelot/felix DSA driver
to a PSEC_PER_NSEC macro. This macro is placed in include/linux/time64.h
as opposed to its relatives (PSEC_PER_SEC etc) from include/vdso/time64.h
because the vDSO library does not (yet) need/use it.
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> # for the vDSO parts
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, sending a packet into a time gate too small for it (or always
closed) causes the queue system to hold the frame forever. Even worse,
this frame isn't subject to aging either, because for that to happen, it
needs to be scheduled for transmission in the first place. But the frame
will consume buffer memory and frame references while it is forever held
in the queue system.
Before commit a4ae997adc ("net: mscc: ocelot: initialize watermarks to
sane defaults"), this behavior was somewhat subtle, as the switch had a
more intricately tuned default watermark configuration out of reset,
which did not allow any single port and tc to consume the entire switch
buffer space. Nonetheless, the held frames are still there, and they
reduce the total backplane capacity of the switch.
However, after the aforementioned commit, the behavior can be very
clearly seen, since we deliberately allow each {port, tc} to consume the
entire shared buffer of the switch minus the reservations (and we
disable all reservations by default). That is to say, we allow a
permanently closed tc-taprio gate to hang the entire switch.
A careful inspection of the documentation shows that the QSYS:Q_MAX_SDU
per-port-tc registers serve 2 purposes: one is for guard band calculation
(when zero, this falls back to QSYS:PORT_MAX_SDU), and the other is to
enable oversized frame dropping (when non-zero).
Currently the QSYS:Q_MAX_SDU registers are all zero, so oversized frame
dropping is disabled. The goal of the change is to enable it seamlessly.
For that, we need to hook into the MTU change, tc-taprio change, and
port link speed change procedures, since we depend on these variables.
Frames are not dropped on egress due to a queue system oversize
condition, instead that egress port is simply excluded from the mask of
valid destination ports for the packet. If there are no destination
ports at all, the ingress counter that increments is the generic
"drop_tail" in ethtool -S.
The issue exists in various forms since the tc-taprio offload was introduced.
Fixes: de143c0e27 ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Reported-by: Richie Pearn <richard.pearn@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In vsc9959_tas_clock_adjust(), the INIT_GATE_STATE field is not changed,
only the ENABLE field. Similarly for the disabling of the time-aware
shaper in vsc9959_qos_port_tas_set().
To reflect this, keep the QSYS_TAG_CONFIG_INIT_GATE_STATE_M mask out of
the read-modify-write procedure to make it clearer what is the intention
of the code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future change we will need to remember the entire tc-taprio config
on all ports rather than just the base time, so use the
taprio_offload_get() helper function to replace ocelot_port->base_time
with ocelot_port->taprio.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
of_parse_phandle() will increase the refcount of 'pcs_node', so add
of_node_put() before return from a5psw_pcs_get().
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220630014153.1888811-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c
9c5de246c1 ("net: sparx5: mdb add/del handle non-sparx5 devices")
fbb89d02e3 ("net: sparx5: Allow mdb entries to both CPU and ports")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both PSFP stats and the port stats read by ocelot_check_stats_work() are
indirectly read through the same mechanism - write to STAT_CFG:STAT_VIEW,
read from SYS:STAT:CNT[n].
It's just that for port stats, we write STAT_VIEW with the index of the
port, and for PSFP stats, we write STAT_VIEW with the filter index.
So if we allow them to run concurrently, ocelot_check_stats_work() may
change the view from vsc9959_psfp_counters_get(), and vice versa.
Fixes: 7d4b564d6a ("net: dsa: felix: support psfp filter on vsc9959")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220629183007.3808130-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The devm_platform_ioremap_resource() function never returns NULL.
It returns error pointers.
Signed-off-by: Peng Wu <wupeng58@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Clément Léger <clement.leger@bootlin.com>
Link: https://lore.kernel.org/r/20220628130920.49493-1-wupeng58@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This switch is calculating tx/rx_bytes for all packets including pause.
So, include rx/tx_pause counter to rx/tx_packets to make tx/rx_bytes fit
to rx/tx_packets.
Link: https://lore.kernel.org/all/20220624220317.ckhx6z7cmzegvoqi@skbuf/
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for pause specific stats.
Tested on ksz9477.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch moves the broadcast ctrl, multicast ctrl and start control
registers from ksz_chip_dat to ksz_chip_reg.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the stp_ctrl_reg from the ksz_chip_data to ksz_chip_reg
structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register size for the ksz8 switches is u8 and for ksz9477 series is
u16. To have common struct for ksz series switches the size of reg is
increased from u8 to u16.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the struct ksz8 from ksz8.h which is no longer
needed. The platform bus specific details are now deferenced through
dev->priv.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves ksz8->shifts from ksz8795.c to ksz_common.c. The shifts
are dereferenced using dev->info->shifts.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the ksz8->masks from ksz8795.c to ksz_common.c. The
mask will be dereferenced using dev->info->masks.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the ksz8->regs from ksz8795.c to the ksz_common.c. And
the regs is dereferrenced using dev->info->regs.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commits add forwarding database support to the driver. It
implements fdb_add(), fdb_del() and fdb_dump().
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add statistics support to the rzn1-a5psw driver by implementing the
following dsa_switch_ops callbacks:
- get_sset_count()
- get_strings()
- get_ethtool_stats()
- get_eth_mac_stats()
- get_eth_ctrl_stats()
- get_rmon_stats()
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Renesas RZ/N1 advanced 5 port switch driver. This switch handles 5
ports including 1 CPU management port. A MDIO bus is also exposed by
this switch and allows to communicate with PHYs connected to the ports.
Each switch port (except for the CPU management ports) is connected to
the MII converter.
This driver includes basic bridging support, more support will be added
later (vlan, etc).
Suggested-by: Jean-Pierre Geslin <jean-pierre.geslin@non.se.com>
Suggested-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of now, there are two spi probes, one ksz8795_spi.c and other
ksz9477_spi.c. This patch combines two files into single ksz_spi.c. The
difference between the two are regmap config and struct ksz8. The regmap
config is assigned based on the platform data. And struct ksz8 is left
untouched, as it is used only ksz8795.c. It can be used for all
other switches also in future.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch delete the ksz8_switch_register and ksz9477_switch_register
since both are calling the ksz_switch_register function. Instead the
ksz_switch_register is called from the probe function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch move the ksz_dev_ops from individual files to ksz_common.c.
And the dev_ops is assigned to ksz_device based on the switch detect.
This reduces the redundant function and allows to reuse the
functionality for LAN937x which has similar register set.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the two different menuconfig for ksz9477 and ksz8795
to single ksz_common. so that it can be extended for the other switch
like lan937x. And removes the export_symbols for the extern functions in
the ksz_common.h.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per 'commit 3506b2f42d ("net: dsa: microchip: call
phy_remove_link_mode during probe")' phy_remove_link_mode is added in
the switch_register function after dsa_switch_register. In order to have
the common switch register function, moving this phylink validation to
phylink_get_caps validation hook.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present, ksz8795.c and ksz9477.c have separate dsa_switch_ops
structure initialization. This patch modifies the files such a way that
ksz switches has common dsa_switch_ops in the ksz_common.c file.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch move the setting the start bit from the individual switch
configuration to ksz_setup
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the enabling the multicast storm protection from
individual setup function to ksz_setup function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch move the 10% broadcast protection from the individual setup
to ksz_setup. In the ksz9477, broadcast protection is updated in reset
function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch move the common initialization of switches to ksz_setup and
perform the switch specific initialization using the ksz_dev_ops
function pointer.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to transmit the STP BPDU packet to the CPU port, the STP
address 01-80-c2-00-00-00 has to be added to static alu table for
ksz8795 series switch. For the ksz9477 switch, there is reserved
multicast table which handles forwarding the particular set of
multicast address to cpu port. So enabling the multicast reserved table
and updated the cpu port index. The stp addr is enabled during the setup
phase using the enable_stp_addr pointer in struct ksz_dev_ops.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To have the common set of initialization in ksz_setup, introduced the
new config_cpu_port member to ksz_dev_ops. Since both the ksz8795.c and
ksz9477.c configuring the cpu port in the setup function, introduced the
member.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames the shutdown to reset in ksz_dev_ops in order to use
the reset dev_ops in the ksz_setup.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pause settings reported by the PHY should also be applied to the GMII port
status override otherwise the switch will not generate pause frames towards the
link partner despite the advertisement saying otherwise.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220623030204.1966851-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
of_find_node_by_name() will decrease the refcount of its first arg and
we need a of_node_get() to keep refcount balance.
Fixes: 7d9ee2e8ff ("net: dsa: hellcreek: Add PTP status LEDs")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220622040621.4094304-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, all the device specific speed setting functions convert
SPEED_MAX to the actual speed of the port. Rather than having each
of the mv88e6xxx chip specifics handling SPEED_MAX, derive it from
the mac_capabilities instead.
This is only needed for CPU and DSA ports, so move the logic up into
mv88e6xxx_setup_port() - which allows us to kill off all users of
SPEED_MAX throughout the driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove mv88e6065_port_set_speed_duplex() - this is never called, and
thus is completely redundant.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
