Right now, the *_port_setup code is in dsa_switch_ops::port_enable(),
which is not the best place for it. This patch moves it to a more
suitable place, dsa_switch_ops::port_setup(), to match the function's
purpose and name.
This patch is a preparation for coming ACL support patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree based drive strength configuration support. It is needed to
pass EMI validation on our hardware.
Configuration values are based on the vendor's reference driver.
Tested on KSZ9563R.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We auto-negotiate most ports in the RTL8366RB driver, but
the CPU port is hard-coded to 1Gbit, full duplex, tx and
rx pause.
This isn't very nice. People may configure speed and
duplex differently in the device tree.
Actually respect the arguments passed to the function for
the CPU port, which get passed properly after Russell's
patch "net: dsa: realtek: add phylink_get_caps implementation"
After this the link is still set up properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when we add the first sja1105 port to a bridge with
vlan_filtering 1, then we sometimes see this output:
sja1105 spi2.2: port 4 failed to read back entry for be:79:b4:9e:9e:96 vid 3088: -ENOENT
sja1105 spi2.2: Reset switch and programmed static config. Reason: VLAN filtering
sja1105 spi2.2: port 0 failed to add be:79:b4:9e:9e:96 vid 0 to fdb: -2
It is because sja1105_fdb_add() runs from the dsa_owq which is no longer
serialized with switch resets since it dropped the rtnl_lock() in the
blamed commit.
Either performing the FDB accesses before the reset, or after the reset,
is equally fine, because sja1105_static_fdb_change() backs up those
changes in the static config, but FDB access during reset isn't ok.
Make sja1105_static_config_reload() take the fdb_lock to fix that.
Fixes: 0faf890fc5 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sja1105_fdb_add() runs from the dsa_owq, and sja1105_port_mcast_flood()
runs from switchdev_deferred_process_work(). Prior to the blamed commit,
they used to be indirectly serialized through the rtnl_lock(), which
no longer holds true because dsa_owq dropped that.
So, it is now possible that we traverse the static config BLK_IDX_L2_LOOKUP
elements concurrently compared to when we change them, in
sja1105_static_fdb_change(). That is not ideal, since it might result in
data corruption.
Introduce a mutex which serializes accesses to the hardware FDB and to
the static config elements for the L2 Address Lookup table.
I can't find a good reason to add locking around sja1105_fdb_dump().
I'll add it later if needed.
Fixes: 0faf890fc5 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit cited in Fixes: did 2 things: it refactored the read-back
polling from sja1105_dynamic_config_read() into a new function,
sja1105_dynamic_config_wait_complete(), and it called that from
sja1105_dynamic_config_write() too.
What is problematic is the refactoring.
The refactored code from sja1105_dynamic_config_poll_valid() works like
the previous one, but the problem is that it uses another packed_buf[]
SPI buffer, and there was code at the end of sja1105_dynamic_config_read()
which was relying on the read-back packed_buf[]:
/* Don't dereference possibly NULL pointer - maybe caller
* only wanted to see whether the entry existed or not.
*/
if (entry)
ops->entry_packing(packed_buf, entry, UNPACK);
After the change, the packed_buf[] that this code sees is no longer the
entry read back from hardware, but the original entry that the caller
passed to the sja1105_dynamic_config_read(), packed into this buffer.
This difference is the most notable with the SJA1105_SEARCH uses from
sja1105pqrs_fdb_add() - used for both fdb and mdb. There, we have logic
added by commit 728db843df ("net: dsa: sja1105: ignore the FDB entry
for unknown multicast when adding a new address") to figure out whether
the address we're trying to add matches on any existing hardware entry,
with the exception of the catch-all multicast address.
That logic was broken, because with sja1105_dynamic_config_read() not
working properly, it doesn't return us the entry read back from
hardware, but the entry that we passed to it. And, since for multicast,
a match will always exist, it will tell us that any mdb entry already
exists at index=0 L2 Address Lookup table. It is index=0 because the
caller doesn't know the index - it wants to find it out, and
sja1105_dynamic_config_read() does:
if (index < 0) { // SJA1105_SEARCH
/* Avoid copying a signed negative number to an u64 */
cmd.index = 0; // <- this
cmd.search = true;
} else {
cmd.index = index;
cmd.search = false;
}
So, to the caller of sja1105_dynamic_config_read(), the returned info
looks entirely legit, and it will add all mdb entries to FDB index 0.
There, they will always overwrite each other (not to mention,
potentially they can also overwrite a pre-existing bridge fdb entry),
and the user-visible impact will be that only the last mdb entry will be
forwarded as it should. The others won't (will be flooded or dropped,
depending on the egress flood settings).
Fixing is a bit more complicated, and involves either passing the same
packed_buf[] to sja1105_dynamic_config_wait_complete(), or moving all
the extra processing on the packed_buf[] to
sja1105_dynamic_config_wait_complete(). I've opted for the latter,
because it makes sja1105_dynamic_config_wait_complete() a bit more
self-contained.
Fixes: df405910ab ("net: dsa: sja1105: wait for dynamic config command completion on writes too")
Reported-by: Yanan Yang <yanan.yang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, sja1105_dynamic_config_wait_complete() returns either 0 or
-ETIMEDOUT, because it just looks at the read_poll_timeout() return code.
There will be future changes which move some more checks to
sja1105_dynamic_config_poll_valid(). It is important that we propagate
their exact return code (-ENOENT, -EINVAL), because callers of
sja1105_dynamic_config_read() depend on them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4d94235495 ("net: dsa: sja1105: offload bridge port flags to
device") has partially hidden some multicast entries from showing up in
the "bridge fdb show" output, but it wasn't enough. Addresses which are
added through "bridge mdb add" still show up. Hide them all.
Fixes: 291d1e72b7 ("net: dsa: sja1105: Add support for FDB and MDB management")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 errata points out (in 'Module 4') the link up/down problems
when EEE (Energy Efficient Ethernet) is enabled in the device to which
the KSZ9477 tries to auto negotiate.
The suggested workaround is to clear advertisement of EEE for PHYs in
this chip driver.
To avoid regressions with other switch ICs the new MICREL_NO_EEE flag
has been introduced.
Moreover, the in-register disablement of MMD_DEVICE_ID_EEE_ADV.MMD_EEE_ADV
MMD register is removed, as this code is both; now executed too late
(after previous rework of the PHY and DSA for KSZ switches) and not
required as setting all members of eee_broken_modes bit field prevents
the KSZ9477 from advertising EEE.
Fixes: 69d3b36ca0 ("net: dsa: microchip: enable EEE support") # for KSZ9477
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # Confirmed disabled EEE with oscilloscope.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230905093315.784052-1-lukma@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit left this delta behind:
struct sja1105_cbs_entry {
- u64 port;
- u64 prio;
+ u64 port; /* Not used for SJA1110 */
+ u64 prio; /* Not used for SJA1110 */
u64 credit_hi;
u64 credit_lo;
u64 send_slope;
u64 idle_slope;
};
but did not actually implement tc-cbs offload fully for the new switch.
The offload is accepted, but it doesn't work.
The difference compared to earlier switch generations is that now, the
table of CBS shapers is sparse, because there are many more shapers, so
the mapping between a {port, prio} and a table index is static, rather
than requiring us to store the port and prio into the sja1105_cbs_entry.
So, the problem is that the code programs the CBS shaper parameters at a
dynamic table index which is incorrect.
All that needs to be done for SJA1110 CBS shapers to work is to bypass
the logic which allocates shapers in a dense manner, as for SJA1105, and
use the fixed mapping instead.
Fixes: 3e77e59bf8 ("net: dsa: sja1105: add support for the SJA1110 switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After running command [2] too many times in a row:
[1] $ tc qdisc add dev sw2p0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0
[2] $ tc qdisc replace dev sw2p0 parent 1:1 cbs offload 1 \
idleslope 120000 sendslope -880000 locredit -1320 hicredit 180
(aka more than priv->info->num_cbs_shapers times)
we start seeing the following error message:
Error: Specified device failed to setup cbs hardware offload.
This comes from the fact that ndo_setup_tc(TC_SETUP_QDISC_CBS) presents
the same API for the qdisc create and replace cases, and the sja1105
driver fails to distinguish between the 2. Thus, it always thinks that
it must allocate the same shaper for a {port, queue} pair, when it may
instead have to replace an existing one.
Fixes: 4d7525085a ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More careful measurement of the tc-cbs bandwidth shows that the stream
bandwidth (effectively idleslope) increases, there is a larger and
larger discrepancy between the rate limit obtained by the software
Qdisc, and the rate limit obtained by its offloaded counterpart.
The discrepancy becomes so large, that e.g. at an idleslope of 40000
(40Mbps), the offloaded cbs does not actually rate limit anything, and
traffic will pass at line rate through a 100 Mbps port.
The reason for the discrepancy is that the hardware documentation I've
been following is incorrect. UM11040.pdf (for SJA1105P/Q/R/S) states
about IDLE_SLOPE that it is "the rate (in unit of bytes/sec) at which
the credit counter is increased".
Cross-checking with UM10944.pdf (for SJA1105E/T) and UM11107.pdf
(for SJA1110), the wording is different: "This field specifies the
value, in bytes per second times link speed, by which the credit counter
is increased".
So there's an extra scaling for link speed that the driver is currently
not accounting for, and apparently (empirically), that link speed is
expressed in Kbps.
I've pondered whether to pollute the sja1105_mac_link_up()
implementation with CBS shaper reprogramming, but I don't think it is
worth it. IMO, the UAPI exposed by tc-cbs requires user space to
recalculate the sendslope anyway, since the formula for that depends on
port_transmit_rate (see man tc-cbs), which is not an invariant from tc's
perspective.
So we use the offload->sendslope and offload->idleslope to deduce the
original port_transmit_rate from the CBS formula, and use that value to
scale the offload->sendslope and offload->idleslope to values that the
hardware understands.
Some numerical data points:
40Mbps stream, max interfering frame size 1500, port speed 100M
---------------------------------------------------------------
tc-cbs parameters:
idleslope 40000 sendslope -60000 locredit -900 hicredit 600
which result in hardware values:
Before (doesn't work) After (works)
credit_hi 600 600
credit_lo 900 900
send_slope 7500000 75
idle_slope 5000000 50
40Mbps stream, max interfering frame size 1500, port speed 1G
-------------------------------------------------------------
tc-cbs parameters:
idleslope 40000 sendslope -960000 locredit -1440 hicredit 60
which result in hardware values:
Before (doesn't work) After (works)
credit_hi 60 60
credit_lo 1440 1440
send_slope 120000000 120
idle_slope 5000000 5
5.12Mbps stream, max interfering frame size 1522, port speed 100M
-----------------------------------------------------------------
tc-cbs parameters:
idleslope 5120 sendslope -94880 locredit -1444 hicredit 77
which result in hardware values:
Before (doesn't work) After (works)
credit_hi 77 77
credit_lo 1444 1444
send_slope 11860000 118
idle_slope 640000 6
Tested on SJA1105T, SJA1105S and SJA1110A, at 1Gbps and 100Mbps.
Fixes: 4d7525085a ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Reported-by: Yanan Yang <yanan.yang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: FLorian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230823085632.116725-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove debug logs in port vlan management, since there are already multiple
tracepoints defined for those operations in DSA
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 91a98917a8 ("net: dsa: microchip: move switch chip_id detection to ksz_common")
removed ksz8_switch_detect() but not its declaration.
Commit 6ec23aaaac ("net: dsa: microchip: move ksz_dev_ops to ksz_common.c")
declared but never implemented other functions.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230821125501.19624-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The user ports use RSGMII, but we don't have that, and DT doesn't
specify a phy interface mode, so phylib defaults to GMII. These support
1G, 100M and 10M with flow control. It is unknown whether asymetric
pause is supported at all speeds.
The CPU port uses MII/GMII/RGMII/REVMII by hardware pin strapping,
and support speeds specific to each, with full duplex only supported
in some modes. Flow control may be supported again by hardware pin
strapping, and theoretically is readable through a register but no
information is given in the datasheet for that.
So, we do a best efforts - and be lenient.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
802.1X PAE frames are link-local frames, therefore they must be trapped to
the CPU port. Currently, the MT753X switches treat 802.1X PAE frames as
regular multicast frames, therefore flooding them to user ports. To fix
this, set 802.1X PAE frames to be trapped to the CPU port(s).
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit resolved a bug where frames would still get stuck at
egress, even though they're smaller than the maxSDU[tc], because the
driver did not take into account the extra 33 ns that the queue system
needs for scheduling the frame.
It now takes that into account, but the arithmetic that we perform in
vsc9959_tas_remaining_gate_len_ps() is buggy, because we operate on
64-bit unsigned integers, so gate_len_ns - VSC9959_TAS_MIN_GATE_LEN_NS
may become a very large integer if gate_len_ns < 33 ns.
In practice, this means that we've introduced a regression where all
traffic class gates which are permanently closed will not get detected
by the driver, and we won't enable oversize frame dropping for them.
Before:
mscc_felix 0000:00:00.5: port 0: max frame size 1526 needs 12400000 ps, 1152000 ps for mPackets at speed 1000
mscc_felix 0000:00:00.5: port 0 tc 0 min gate len 1000000, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 1 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 2 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 3 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 4 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 5 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 6 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 5120 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 615 octets including FCS
After:
mscc_felix 0000:00:00.5: port 0: max frame size 1526 needs 12400000 ps, 1152000 ps for mPackets at speed 1000
mscc_felix 0000:00:00.5: port 0 tc 0 min gate len 1000000, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 5120 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 615 octets including FCS
Fixes: 11afdc6526 ("net: dsa: felix: tc-taprio intervals smaller than MTU should send at least one packet")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230817120111.3522827-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/sfc/tc.c
fa165e1949 ("sfc: don't unregister flow_indr if it was never registered")
3bf969e88a ("sfc: add MAE table machinery for conntrack table")
https://lore.kernel.org/all/20230818112159.7430e9b4@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the switch is reset during active EEPROM transactions, as in
just after an SoC reset after power up, the I2C bus transaction
may be cut short leaving the EEPROM internal I2C state machine
in the wrong state. When the switch is reset again, the bad
state machine state may result in data being read from the wrong
memory location causing the switch to enter unexpected mode
rendering it inoperational.
Fixes: a3dcb3e7e7 ("net: dsa: mv88e6xxx: Wait for EEPROM done after HW reset")
Signed-off-by: Alfred Lee <l00g33k@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230815001323.24739-1-l00g33k@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver depends on CONFIG_OF, it is not necessary to use
of_match_ptr() here.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver depends on CONFIG_OF, it is not necessary to use
of_match_ptr() here.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phylink_get_caps implementation for Marvell 88e6060 DSA switch.
This is a fast ethernet switch, with internal PHYs for ports 0 through
4. Port 4 also supports MII, REVMII, REVRMII and SNI. Port 5 supports
MII, REVMII, REVRMII and SNI without an internal PHY.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/E1qUkx7-003dMX-9b@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for vlan operation (add, del, filtering) on the RZN1
driver. The a5psw switch supports up to 32 VLAN IDs with filtering,
tagged/untagged VLANs and PVID for each ports.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running vlan test (bridge_vlan_aware/unaware.sh), there were some
failure due to the lack .port_bridge_flag function to disable port
flooding. Implement this operation for BR_LEARNING, BR_FLOOD,
BR_MCAST_FLOOD and BR_BCAST_FLOOD.
Since .port_bridge_flags affects the bits disabling learning for a port,
ensure that any other modification on the same register done by
a5psw_port_stp_state_set is in sync by using the port learning state to
enable/disable learning on the port.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
.port_bridge_flags will be added and allows to modify the flood mask
independently for each port. Keeping the existing bridged_ports write
in a5psw_flooding_set_resolution() would potentially messed up this.
Use a read-modify-write to set that value and move bridged_ports
handling in bridge_port_join/leave.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different MT7530 variants require different PHY drivers.
Use 'imply' instead of 'select' to relax the dependency on the PHY
driver, and choose the appropriate driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the tagging protocol in current use is "ocelot-8021q" and we unbind
the driver, we see this splat:
$ echo '0000:00:00.2' > /sys/bus/pci/drivers/fsl_enetc/unbind
mscc_felix 0000:00:00.5 swp0: left promiscuous mode
sja1105 spi2.0: Link is Down
DSA: tree 1 torn down
mscc_felix 0000:00:00.5 swp2: left promiscuous mode
sja1105 spi2.2: Link is Down
DSA: tree 3 torn down
fsl_enetc 0000:00:00.2 eno2: left promiscuous mode
mscc_felix 0000:00:00.5: Link is Down
------------[ cut here ]------------
RTNL: assertion failed at net/dsa/tag_8021q.c (409)
WARNING: CPU: 1 PID: 329 at net/dsa/tag_8021q.c:409 dsa_tag_8021q_unregister+0x12c/0x1a0
Modules linked in:
CPU: 1 PID: 329 Comm: bash Not tainted 6.5.0-rc3+ #771
pc : dsa_tag_8021q_unregister+0x12c/0x1a0
lr : dsa_tag_8021q_unregister+0x12c/0x1a0
Call trace:
dsa_tag_8021q_unregister+0x12c/0x1a0
felix_tag_8021q_teardown+0x130/0x150
felix_teardown+0x3c/0xd8
dsa_tree_teardown_switches+0xbc/0xe0
dsa_unregister_switch+0x168/0x260
felix_pci_remove+0x30/0x60
pci_device_remove+0x4c/0x100
device_release_driver_internal+0x188/0x288
device_links_unbind_consumers+0xfc/0x138
device_release_driver_internal+0xe0/0x288
device_driver_detach+0x24/0x38
unbind_store+0xd8/0x108
drv_attr_store+0x30/0x50
---[ end trace 0000000000000000 ]---
------------[ cut here ]------------
RTNL: assertion failed at net/8021q/vlan_core.c (376)
WARNING: CPU: 1 PID: 329 at net/8021q/vlan_core.c:376 vlan_vid_del+0x1b8/0x1f0
CPU: 1 PID: 329 Comm: bash Tainted: G W 6.5.0-rc3+ #771
pc : vlan_vid_del+0x1b8/0x1f0
lr : vlan_vid_del+0x1b8/0x1f0
dsa_tag_8021q_unregister+0x8c/0x1a0
felix_tag_8021q_teardown+0x130/0x150
felix_teardown+0x3c/0xd8
dsa_tree_teardown_switches+0xbc/0xe0
dsa_unregister_switch+0x168/0x260
felix_pci_remove+0x30/0x60
pci_device_remove+0x4c/0x100
device_release_driver_internal+0x188/0x288
device_links_unbind_consumers+0xfc/0x138
device_release_driver_internal+0xe0/0x288
device_driver_detach+0x24/0x38
unbind_store+0xd8/0x108
drv_attr_store+0x30/0x50
DSA: tree 0 torn down
This was somewhat not so easy to spot, because "ocelot-8021q" is not the
default tagging protocol, and thus, not everyone who tests the unbinding
path may have switched to it beforehand. The default
felix_tag_npi_teardown() does not require rtnl_lock() to be held.
Fixes: 7c83a7c539 ("net: dsa: add a second tagger for Ocelot switches based on tag_8021q")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230803134253.2711124-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace bogus comment about matching the latched timestamp to one of the
received frames. That comment is probably copied from mv88e6xxx and true for
these switches. However, the hellcreek switch is configured to insert the
timestamp directly into the PTP packets.
While here, remove the other comments regarding the list splicing and locking as
well, because it doesn't add any value.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230801131647.84697-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes XAUI/RXAUI lane alignment errors.
Issue causes dropped packets when trying to communicate over
fiber via SERDES lanes of port 9 and 10.
Errata document applies only to 88E6190X and 88E6390X devices.
Requires poking in undocumented registers.
Signed-off-by: Ante Knezic <ante.knezic@helmholz.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert for loop to dsa_for_each macro to save some redundant write on
unconnected/unused port and tidy things up.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230730074113.21889-5-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Move qca8xxx hol fixup to separate function to tidy things up and to
permit using a more efficent loop in future patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230730074113.21889-4-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In preparation for multi-CPU support, set CPU port LOOKUP MEMBER outside
the port loop and setup the LOOKUP MEMBER mask for user ports only to
the first CPU port.
This is to handle flooding condition where every CPU port is set as
target and prevent packet duplication for unknown frames from user ports.
Secondary CPU port LOOKUP MEMBER mask will be setup later when
port_change_master will be implemented.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230730074113.21889-3-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Address learning should initially be turned off by the driver for port
operation in standalone mode, then the DSA core handles changes to it
via ds->ops->port_bridge_flags().
Currently this is not the case for qca8k where learning is enabled
unconditionally in qca8k_setup for every user port.
Handle ports configured in standalone mode by making the learning
configurable and not enabling it by default.
Implement .port_pre_bridge_flags and .port_bridge_flags dsa ops to
enable learning for bridge that request it and tweak
.port_stp_state_set to correctly disable learning when port is
configured in standalone mode.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230730074113.21889-2-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As 32bits of dissector->used_keys are exhausted,
increase the size to 64bits.
This is base change for ESP/AH flow dissector patch.
Please find patch and discussions at
https://lore.kernel.org/netdev/ZMDNjD46BvZ5zp5I@corigine.com/T/#t
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Tested-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit (SHA1: 5c844d57aa) provided code
to apply "Module 6: Certain PHY registers must be written as pairs instead
of singly" errata for KSZ9477 as this chip for certain PHY registers
(0xN120 to 0xN13F, N=1,2,3,4,5) must be accesses as 32 bit words instead
of 16 or 8 bit access.
Otherwise, adjacent registers (no matter if reserved or not) are
overwritten with 0x0.
Without this patch some registers (e.g. 0x113c or 0x1134) required for 32
bit access are out of valid regmap ranges.
As a result, following error is observed and KSZ9477 is not properly
configured:
ksz-switch spi1.0: can't rmw 32bit reg 0x113c: -EIO
ksz-switch spi1.0: can't rmw 32bit reg 0x1134: -EIO
ksz-switch spi1.0 lan1 (uninitialized): failed to connect to PHY: -EIO
ksz-switch spi1.0 lan1 (uninitialized): error -5 setting up PHY for tree 0, switch 0, port 0
The solution is to modify regmap_reg_range to allow accesses with 4 bytes
boundaries.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
in bcm_sf2_sw_probe(), check the return value of clk_prepare_enable()
and return the error code if clk_prepare_enable() returns an
unexpected value.
Fixes: e9ec5c3bd2 ("net: dsa: bcm_sf2: request and handle clocks")
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230726170506.16547-1-ruc_gongyuanjun@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230724211859.805481-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The qca8k switch doesn't support using 0 as VID and require a default
VID to be always set. MDB add/del function doesn't currently handle
this and are currently setting the default VID.
Fix this by correctly handling this corner case and internally use the
default VID for VID 0 case.
Fixes: ba8f870dfa ("net: dsa: qca8k: add support for mdb_add/del")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
On deleting an MDB entry for a port, fdb_search_and_del is used.
An FDB entry can't be modified so it needs to be deleted and readded
again with the new portmap (and the port deleted as requested)
We use the SEARCH operator to search the entry to edit by vid and mac
address and then we check the aging if we actually found an entry.
Currently the code suffer from a bug where the searched fdb entry is
never read again with the found values (if found) resulting in the code
always returning -EINVAL as aging was always 0.
Fix this by correctly read the fdb entry after it was searched.
Fixes: ba8f870dfa ("net: dsa: qca8k: add support for mdb_add/del")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
On inserting a mdb entry, fdb_search_and_insert is used to add a port to
the qca8k target entry in the FDB db.
A FDB entry can't be modified so it needs to be removed and insert again
with the new values.
To detect if an entry already exist, the SEARCH operation is used and we
check the aging of the entry. If the entry is not 0, the entry exist and
we proceed to delete it.
Current code have 2 main problem:
- The condition to check if the FDB entry exist is wrong and should be
the opposite.
- When a FDB entry doesn't exist, aging was never actually set to the
STATIC value resulting in allocating an invalid entry.
Fix both problem by adding aging support to the function, calling the
function with STATIC as aging by default and finally by correct the
condition to check if the entry actually exist.
Fixes: ba8f870dfa ("net: dsa: qca8k: add support for mdb_add/del")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The qca8xxx switch supports 2 way to write reg values, a slow way using
mdio and a fast way by sending specially crafted mgmt packet to
read/write reg.
The fast way can support up to 32 bytes of data as eth packet are used
to send/receive.
This correctly works for almost the entire regmap of the switch but with
the use of some kernel selftests for dsa drivers it was found a funny
and interesting hw defect/limitation.
For some specific reg, bulk write won't work and will result in writing
only part of the requested regs resulting in half data written. This was
especially hard to track and discover due to the total strangeness of
the problem and also by the specific regs where this occurs.
This occurs in the specific regs of the ATU table, where multiple entry
needs to be written to compose the entire entry.
It was discovered that with a bulk write of 12 bytes on
QCA8K_REG_ATU_DATA0 only QCA8K_REG_ATU_DATA0 and QCA8K_REG_ATU_DATA2
were written, but QCA8K_REG_ATU_DATA1 was always zero.
Tcpdump was used to make sure the specially crafted packet was correct
and this was confirmed.
The problem was hard to track as the lack of QCA8K_REG_ATU_DATA1
resulted in an entry somehow possible as the first bytes of the mac
address are set in QCA8K_REG_ATU_DATA0 and the entry type is set in
QCA8K_REG_ATU_DATA2.
Funlly enough writing QCA8K_REG_ATU_DATA1 results in the same problem
with QCA8K_REG_ATU_DATA2 empty and QCA8K_REG_ATU_DATA1 and
QCA8K_REG_ATU_FUNC correctly written.
A speculation on the problem might be that there are some kind of
indirection internally when accessing these regs and they can't be
accessed all together, due to the fact that it's really a table mapped
somewhere in the switch SRAM.
Even more funny is the fact that every other reg was tested with all
kind of combination and they are not affected by this problem. Read
operation was also tested and always worked so it's not affected by this
problem.
The problem is not present if we limit writing a single reg at times.
To handle this hardware defect, enable use_single_write so that bulk
api can correctly split the write in multiple different operation
effectively reverting to a non-bulk write.
Cc: Mark Brown <broonie@kernel.org>
Fixes: c766e077d9 ("net: dsa: qca8k: convert to regmap read/write API")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Since DSA no longer marks anything as phylink-legacy, there is now no
need for DSA drivers to set this member to false. Remove all instances
of this.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The KSZ8795 driver code was modified to use on KSZ8863/73, which has
different register definitions. Some of the new KSZ8795 register
information are wrong compared to previous code.
KSZ8795 also behaves differently in that the STATIC_MAC_TABLE_USE_FID
and STATIC_MAC_TABLE_FID bits are off by 1 when doing MAC table reading
than writing. To compensate that a special code was added to shift the
register value by 1 before applying those bits. This is wrong when the
code is running on KSZ8863, so this special code is only executed when
KSZ8795 is detected.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mv88e6xxx is completely converted to using phylink_pcs
support, we have no need for the serdes methods. Remove all this
infrastructure. Also remove the __maybe_unused from
mv88e6xxx_pcs_select().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the 88E6390, 88E6390X, and 88E6393X family of switches to use
the phylink_pcs infrastructure.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the 88E6352 SERDES code to use the phylink_pcs infrastructure.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the 88E6185 SERDES code to use the phylink_pcs infrastructure.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename and export the PCS state decoding function so our PCS can
make use of the functionality provided by this.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure for phylink_pcs to the mv88e6xxx driver. This
involves adding a mac_select_pcs() hook so we can pass the PCS to
phylink at the appropriate time, and a PCS initialisation function.
As the various chip implementations are converted to use phylink_pcs,
they are no longer reliant on the legacy phylink behaviour. We detect
this by the use of this infrastructure, or the lack of any serdes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we now always use a fixed-link for DSA and CPU ports, we no longer
need the hack in the Marvell code to make this work. Remove it.
This is especially important with the conversion of DSA drivers to
phylink_pcs, as the PCS code only gets called if we are using
phylink for the port.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now have a regmap cache which uses a maple tree to store the register
state, this is a more modern data structure and the regmap level code
using it makes a number of assumptions better tuned for modern hardware
than those made by the rbtree cache type that the at9331 driver uses.
Switch the ar9331 driver to use the more modern data structure.
This should have minimal practical impact, it's mainly code
modernisation.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The at9331 is only able to read or write a single register at once. The
driver has a custom regmap bus and chooses to tell the regmap core about
this by reporting the maximum transfer sizes rather than the explicit
flags that exist at the regmap level. Since there are a number of
problems with the raw transfer limits and the regmap level flags are
better integrated anyway convert the driver to use the flags.
No functional change.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I get sporadic timeouts from the driver when using the
MV88E6352. Reading the status again after the loop fixes the
problem: the operation is successful but goes undetected.
Some added prints show things like this:
[ 58.356209] mv88e6085 mdio_mux-0.1:00: Timeout while waiting
for switch, addr 1b reg 0b, mask 8000, val 0000, data c000
[ 58.367487] mv88e6085 mdio_mux-0.1:00: Timeout waiting for
ATU op 4000, fid 0001
(...)
[ 61.826293] mv88e6085 mdio_mux-0.1:00: Timeout while waiting
for switch, addr 1c reg 18, mask 8000, val 0000, data 9860
[ 61.837560] mv88e6085 mdio_mux-0.1:00: Timeout waiting
for PHY command 1860 to complete
The reason is probably not the commands: I think those are
mostly fine with the 50+50ms timeout, but the problem
appears when OpenWrt brings up several interfaces in
parallel on a system with 7 populated ports: if one of
them take more than 50 ms and waits one or more of the
others can get stuck on the mutex for the switch and then
this can easily multiply.
As we sleep and wait, the function loop needs a final
check after exiting the loop if we were successful.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Cc: Tobias Waldekranz <tobias@waldekranz.com>
Fixes: 35da1dfd94 ("net: dsa: mv88e6xxx: Improve performance of busy bit polling")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230712223405.861899-1-linus.walleij@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary of_node_put from the continue path to prevent
child node from being released twice, which could avoid resource
leak or other unexpected issues.
Signed-off-by: Lu Hongfei <luhongfei@vivo.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Fixes: de879a016a ("net: dsa: felix: add functionality when not all ports are supported")
Link: https://lore.kernel.org/r/20230710031859.36784-1-luhongfei@vivo.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add check for the return value of skb_copy in order to avoid NULL pointer
dereference.
Fixes: 2cd5485663 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switch implements Hold/Release in a strange way, with no control
from the user as required by IEEE 802.1Q-2018 through Set-And-Hold-MAC
and Set-And-Release-MAC, but rather, it emits HOLD requests implicitly
based on the schedule.
Namely, when the gate of a preemptible TC is about to close (actually
QSYS::PREEMPTION_CFG.HOLD_ADVANCE octet times in advance of this event),
the QSYS seems to emit a HOLD request pulse towards the MAC which
preempts the currently transmitted packet, and further packets are held
back in the queue system.
This allows large frames to be squeezed through small time slots,
because HOLD requests initiated by the gate events result in the frame
being segmented in multiple fragments, the bit time of which is equal to
the size of the time slot.
It has been reported that the vsc9959_tas_guard_bands_update() logic
breaks this, because it doesn't take preemptible TCs into account, and
enables oversized frame dropping when the time slot doesn't allow a full
MTU to be sent, but it does allow 2*minFragSize to be sent (128B).
Packets larger than 128B are dropped instead of being sent in multiple
fragments.
Confusingly, the manual says:
| For guard band, SDU calculation of a traffic class of a port, if
| preemption is enabled (through 'QSYS::PREEMPTION_CFG.P_QUEUES') then
| QSYS::PREEMPTION_CFG.HOLD_ADVANCE is used, otherwise
| QSYS::QMAXSDU_CFG_*.QMAXSDU_* is used.
but this only refers to the static guard band durations, and the
QMAXSDU_CFG_* registers have dual purpose - the other being oversized
frame dropping, which takes place irrespective of whether frames are
preemptible or express.
So, to fix the problem, we need to call vsc9959_tas_guard_bands_update()
from ocelot_port_update_active_preemptible_tcs(), and modify the guard
band logic to consider a different (lower) oversize limit for
preemptible traffic classes.
Fixes: 403ffc2c34 ("net: mscc: ocelot: add support for preemptible traffic classes")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-ID: <20230705104422.49025-4-vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future change we will need to make
ocelot_port_update_active_preemptible_tcs() call
vsc9959_tas_guard_bands_update(), but that is currently not possible,
since the ocelot switch lib does not have access to functions private to
the DSA wrapper.
Move the pointer to vsc9959_tas_guard_bands_update() from felix->info
(which is private to the DSA driver) to ocelot->ops (which is also
visible to the ocelot switch lib).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-ID: <20230705104422.49025-3-vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future commit we will have to call vsc9959_tas_guard_bands_update()
from ocelot_port_update_active_preemptible_tcs(), and that will be
impossible due to the AB/BA locking dependencies between
ocelot->tas_lock and ocelot->fwd_domain_lock.
Just like we did in commit 3ff468ef98 ("net: mscc: ocelot: remove
struct ocelot_mm_state :: lock"), the only solution is to expand the
scope of ocelot->fwd_domain_lock for it to also serialize changes made
to the Time-Aware Shaper, because those will have to result in a
recalculation of cut-through TCs, which is something that depends on the
forwarding domain.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-ID: <20230705104422.49025-2-vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
incl_srcpt has the limitation, mentioned in commit b4638af888 ("net:
dsa: sja1105: always enable the INCL_SRCPT option"), that frames with a
MAC DA of 01:80:c2:xx:yy:zz will be received as 01:80:c2:00:00:zz unless
PTP RX timestamping is enabled.
The incl_srcpt option was initially unconditionally enabled, then that
changed with commit 42824463d3 ("net: dsa: sja1105: Limit use of
incl_srcpt to bridge+vlan mode"), then again with b4638af888 ("net:
dsa: sja1105: always enable the INCL_SRCPT option"). Bottom line is that
it now needs to be always enabled, otherwise the driver does not have a
reliable source of information regarding source_port and switch_id for
link-local traffic (tag_8021q VLANs may be imprecise since now they
identify an entire bridging domain when ports are not standalone).
If we accept that PTP RX timestamping (and therefore, meta frame
generation) is always enabled in hardware, then that limitation could be
avoided and packets with any MAC DA can be properly received, because
meta frames do contain the original bytes from the MAC DA of their
associated link-local packet.
This change enables meta frame generation unconditionally, which also
has the nice side effects of simplifying the switch control path
(a switch reset is no longer required on hwtstamping settings change)
and the tagger data path (it no longer needs to be informed whether to
expect meta frames or not - it always does).
Fixes: 227d07a07e ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch in MAXLEN register stores the maximum size of a data frame.
The MTU size is 18 bytes smaller than the frame size.
The current settings are causing problems with packet forwarding.
This patch fixes the MTU settings to proper values.
Fixes: fb77ffc6ec ("net: dsa: vsc73xx: make the MTU configurable")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230628194327.1765644-1-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link-local traffic on bridged SJA1105 ports is sometimes tagged by the
hardware with source port information (when the port is under a VLAN
aware bridge).
The tag_8021q source port identification has become more loose
("imprecise") and will report a plausible rather than exact bridge port,
when under a bridge (be it VLAN-aware or VLAN-unaware). But link-local
traffic always needs to know the precise source port.
Modify the driver logic (and therefore: the tagging protocol itself) to
always include the source port information with link-local packets,
regardless of whether the port is standalone, under a VLAN-aware or
VLAN-unaware bridge. This makes it possible for the tagging driver to
give priority to that information over the tag_8021q VLAN header.
The big drawback with INCL_SRCPT is that it makes it impossible to
distinguish between an original MAC DA of 01:80:C2:XX:YY:ZZ and
01:80:C2:AA:BB:ZZ, because the tagger just patches MAC DA bytes 3 and 4
with zeroes. Only if PTP RX timestamping is enabled, the switch will
generate a META follow-up frame containing the RX timestamp and the
original bytes 3 and 4 of the MAC DA. Those will be used to patch up the
original packet. Nonetheless, in the absence of PTP RX timestamping, we
have to live with this limitation, since it is more important to have
the more precise source port information for link-local traffic.
Fixes: d7f9787a76 ("net: dsa: tag_8021q: add support for imprecise RX based on the VBID")
Fixes: 91495f21fc ("net: dsa: tag_8021q: replace the SVL bridging with VLAN-unaware IVL bridging")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver implements a workaround for the fact that it doesn't have an
IRQ source to tell it whether PTP frames are available through the
extraction registers, for those frames to be processed and passed
towards the network stack. That workaround is to configure the switch,
through felix_hwtstamp_set() -> felix_update_trapping_destinations(),
to create two copies of PTP packets: one sent over Ethernet to the DSA
master, and one to be consumed through the aforementioned CPU extraction
queue registers.
The reason why we want PTP packets to be consumed through the CPU
extraction registers in the first place is because we want to see their
hardware RX timestamp. With tag_8021q, that is only visible that way,
and it isn't visible with the copy of the packet that's transmitted over
Ethernet.
The problem with the workaround implementation is that it drops the
packet received over Ethernet, in expectation of its copy being present
in the CPU extraction registers. However, if felix_hwtstamp_set() hasn't
run (aka PTP RX timestamping is disabled), the driver will drop the
original PTP frame and there will be no copy of it in the CPU extraction
registers. So, the network stack will simply not see any PTP frame.
Look at the port's trapping configuration to see whether the driver has
previously enabled the CPU extraction registers. If it hasn't, just
don't RX timestamp the frame and let it be passed up the stack by DSA,
which is perfectly fine.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The QCA8K switch supports additional modes that can be handled in
hardware for the LED netdev trigger.
Add these additional modes to further support the Switch LEDs and
offload more blink modes.
Add additional modes:
- link_10
- link_100
- link_1000
- half_duplex
- full_duplex
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230621095409.25859-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the errata sheets for ksz9477 and ksz9567, writes to the
PHY registers 0x10-0x1f (i.e. those located at addresses 0xN120 to
0xN13f) must be done as a 32 bit write to the 4-byte aligned address
containing the register, hence requires a RMW in order not to change
the adjacent PHY register.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230620113855.733526-4-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This will be used in a subsequent patch fixing an errata for writes to
certain PHY registers.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20230620113855.733526-3-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement ksz_prmw8() in terms of ksz_rmw8(), just as all the other
ksz_pX are implemented in terms of ksz_X. No functional change.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20230620113855.733526-2-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update mt7530's embedded PCS driver to use neg_mode, even though it
makes no use of it or the "mode" argument. This makes the driver
consistent with converted drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Ej-00EaGR-Fk@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update B53's embedded PCS driver to use neg_mode, even though it makes
no use of it or the "mode" argument. This makes the driver consistent
with converted drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1qA8Ee-00EaGL-Az@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update qca8k's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EU-00EaG9-1l@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update xpcs to use neg_mode to configure whether inband negotiation
should be used. We need to update sja1105 as well as that directly
calls into the XPCS driver's config function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Dt-00EaFS-W9@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the introduction of the OF bindings, DSA has always had a policy that
in case multiple CPU ports are present in the device tree, the numerically
smallest one is always chosen.
The MT7530 switch family, except the switch on the MT7988 SoC, has 2 CPU
ports, 5 and 6, where port 6 is preferable on the MT7531BE switch because
it has higher bandwidth.
The MT7530 driver developers had 3 options:
- to modify DSA when the MT7531 switch support was introduced, such as to
prefer the better port
- to declare both CPU ports in device trees as CPU ports, and live with the
sub-optimal performance resulting from not preferring the better port
- to declare just port 6 in the device tree as a CPU port
Of course they chose the path of least resistance (3rd option), kicking the
can down the road. The hardware description in the device tree is supposed
to be stable - developers are not supposed to adopt the strategy of
piecemeal hardware description, where the device tree is updated in
lockstep with the features that the kernel currently supports.
Now, as a result of the fact that they did that, any attempts to modify the
device tree and describe both CPU ports as CPU ports would make DSA change
its default selection from port 6 to 5, effectively resulting in a
performance degradation visible to users with the MT7531BE switch as can be
seen below.
Without preferring port 6:
[ ID][Role] Interval Transfer Bitrate Retr
[ 5][TX-C] 0.00-20.00 sec 374 MBytes 157 Mbits/sec 734 sender
[ 5][TX-C] 0.00-20.00 sec 373 MBytes 156 Mbits/sec receiver
[ 7][RX-C] 0.00-20.00 sec 1.81 GBytes 778 Mbits/sec 0 sender
[ 7][RX-C] 0.00-20.00 sec 1.81 GBytes 777 Mbits/sec receiver
With preferring port 6:
[ ID][Role] Interval Transfer Bitrate Retr
[ 5][TX-C] 0.00-20.00 sec 1.99 GBytes 856 Mbits/sec 273 sender
[ 5][TX-C] 0.00-20.00 sec 1.99 GBytes 855 Mbits/sec receiver
[ 7][RX-C] 0.00-20.00 sec 1.72 GBytes 737 Mbits/sec 15 sender
[ 7][RX-C] 0.00-20.00 sec 1.71 GBytes 736 Mbits/sec receiver
Using one port for WAN and the other ports for LAN is a very popular use
case which is what this test emulates.
As such, this change proposes that we retroactively modify stable kernels
(which don't support the modification of the CPU port assignments, so as to
let user space fix the problem and restore the throughput) to keep the
mt7530 driver preferring port 6 even with device trees where the hardware
is more fully described.
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LLDP frames are link-local frames, therefore they must be trapped to the
CPU port. Currently, the MT753X switches treat LLDP frames as regular
multicast frames, therefore flooding them to user ports. To fix this, set
LLDP frames to be trapped to the CPU port(s).
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPDUs are link-local frames, therefore they must be trapped to the CPU
port. Currently, the MT7530 switch treats BPDUs as regular multicast
frames, therefore flooding them to user ports. To fix this, set BPDUs to be
trapped to the CPU port. Group this on mt7530_setup() and
mt7531_setup_common() into mt753x_trap_frames() and call that.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All MT7530 switch IP variants share the MT7530_MFC register, but the
current driver only writes it for the switch variant that is integrated in
the MT7621 SoC. Modify the code to include all MT7530 derivatives.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MT7531_CPU_PMAP represents the destination port mask for trapped-to-CPU
frames (further restricted by PCR_MATRIX).
Currently the driver sets the first CPU port as the single port in this bit
mask, which works fine regardless of whether the device tree defines port
5, 6 or 5+6 as CPU ports. This is because the logic coincides with DSA's
logic of picking the first CPU port as the CPU port that all user ports are
affine to, by default.
An upcoming change would like to influence DSA's selection of the default
CPU port to no longer be the first one, and in that case, this logic needs
adaptation.
Since there is no observed leakage or duplication of frames if all CPU
ports are defined in this bit mask, simply include them all.
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DEV_MAC_MAXLEN_CFG register contains a 16-bit value - up to 65535.
Plus 2 * VLAN_HLEN (4), that is up to 65543.
The picos_per_byte variable is the largest when "speed" is lowest -
SPEED_10 = 10. In that case it is (1000000L * 8) / 10 = 800000.
Their product - 52434400000 - exceeds 32 bits, which is a problem,
because apparently, a multiplication between two 32-bit factors is
evaluated as 32-bit before being assigned to a 64-bit variable.
In fact it's a problem for any MTU value larger than 5368.
Cast one of the factors of the multiplication to u64 to force the
multiplication to take place on 64 bits.
Issue found by Coverity.
Fixes: 55a515b1f5 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230613170907.2413559-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
Conflicts:
net/sched/sch_taprio.c
d636fc5dd6 ("net: sched: add rcu annotations around qdisc->qdisc_sleeping")
dced11ef84 ("net/sched: taprio: don't overwrite "sch" variable in taprio_dump_class_stats()")
net/ipv4/sysctl_net_ipv4.c
e209fee411 ("net/ipv4: ping_group_range: allow GID from 2147483648 to 4294967294")
ccce324dab ("tcp: make the first N SYN RTO backoffs linear")
https://lore.kernel.org/all/20230605100816.08d41a7b@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pointer variables of (void*) type do not require type cast.
Signed-off-by: Atin Bainada <hi@atinb.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
This error path needs call mutex_unlock(&ocelot->tas_lock) before
returning.
Fixes: 2d800bc500 ("net/sched: taprio: replace tc_taprio_qopt_offload :: enable with a "cmd" enum")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 PHY errata handling code has now been moved into the Micrel
PHY driver, so it is no longer needed inside the DSA switch driver.
Remove it.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new xpcs_create_mdiodev() creator, which simplifies the
creation and destruction of the mdio device associated with xpcs.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the mdiodev after xpcs_create() so that the XPCS driver can manage
the lifetime of the mdiodev its using.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without LED triggers, the driver now fails to build:
drivers/net/dsa/qca/qca8k-leds.c: In function 'qca8k_parse_port_leds':
drivers/net/dsa/qca/qca8k-leds.c:403:31: error: 'struct led_classdev' has no member named 'hw_control_is_supported'
403 | port_led->cdev.hw_control_is_supported = qca8k_cled_hw_control_is_supported;
| ^
There is a mix of 'depends on' and 'select' for LEDS_TRIGGERS, so it's
not clear what we should use here, but in general using 'depends on'
causes fewer problems, so use that.
Fixes: e0256648c8 ("net: dsa: qca8k: implement hw_control ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN9303 doesn't associate FDB (ALR) entries with VLANs, it has just one
global Address Logic Resolution table [1].
Ignore VID in port_fdb_{add|del} methods, go on with the global table. This
is the same semantics as hellcreek or RZ/N1 implement.
Visible symptoms:
LAN9303_MDIO 5b050000.ethernet-1:00: port 2 failed to delete 00:xx:xx:xx:xx:cf vid 1 from fdb: -2
LAN9303_MDIO 5b050000.ethernet-1:00: port 2 failed to add 00:xx:xx:xx:xx:cf vid 1 to fdb: -95
[1] https://ww1.microchip.com/downloads/en/DeviceDoc/00002308A.pdf
Fixes: 0620427ea0 ("net: dsa: lan9303: Add fdb/mdb manipulation")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230531143826.477267-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A switch held in reset by default needs to wait longer until we can
reliably detect it.
An issue was observed when testing on the Marvell 88E6393X (Link Street).
The driver failed to detect the switch on some upstarts. Increasing the
wait time after reset deactivation solves this issue.
The updated wait time is now also the same as the wait time in the
mv88e6xxx_hardware_reset function.
Fixes: 7b75e49de4 ("net: dsa: mv88e6xxx: wait after reset deactivation")
Signed-off-by: Andreas Svensson <andreas.svensson@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230530145223.1223993-1-andreas.svensson@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Inspired from struct flow_cls_offload :: cmd, in order for taprio to be
able to report statistics (which is future work), it seems that we need
to drill one step further with the ndo_setup_tc(TC_SETUP_QDISC_TAPRIO)
multiplexing, and pass the command as part of the common portion of the
muxed structure.
Since we already have an "enable" variable in tc_taprio_qopt_offload,
refactor all drivers to check for "cmd" instead of "enable", and reject
every other command except "replace" and "destroy" - to be future proof.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> # for lan966x
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A mv88e6250 family switch with 5 internal PHYs, 2 RMIIs
and no PTP support.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A mv88e6250 family switch with 2 PHY and RMII ports and
no PTP support.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switches from mv88e6250 family (including mv88e6020 and mv88e6071) need
the possibility to setup the maximal frame size, as they support frames
up to 2048 bytes.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order that the LED trigger can blink the switch MAC ports LED, it
needs to know the netdev associated to the port. Add the callback to
return the struct device of the netdev.
Add an helper function qca8k_phy_to_port() to convert the phy back to
dsa_port index, as we reference LED port based on the internal PHY
index and needs to be converted back.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement hw_control ops to drive Switch LEDs based on hardware events.
Netdev trigger is the declared supported trigger for hw control
operation and supports the following mode:
- tx
- rx
When hw_control_set is called, LEDs are set to follow the requested
mode.
Each LEDs will blink at 4Hz by default.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E6361 is an 8-port switch derived from the
88E6393X/88E9193X/88E6191X switches family. It can benefit from the
existing mv88e6xxx driver by simply adding the proper switch description in
the driver. Main differences with other switches from this
family are:
- 8 ports exposed (instead of 11): ports 1, 2 and 8 not available
- No 5GBase-x nor SFI/USXGMII support
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some switches families have minor differences on supported link speed for
ports. Instead of redefining a new port_max_speed_mode for each different
configuration, allow to pass mv88e6xxx_chip structure to allow
differentiating those chips by known chip id
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
88E6393X/88E6193X/88E6191X switches have in fact 8 internal PHYs, but those
are not present starting at port 0: supported ports go from 1 to 8
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mv88e6xxx currently assumes that switch equipped with internal phys have
those phys mapped contiguously starting from port 0 (see
mv88e6xxx_phy_is_internal). However, some switches have internal PHYs but
NOT starting from port 0. For example 88e6393X, 88E6193X and 88E6191X have
integrated PHYs available on ports 1 to 8
To properly support this offset, add a new field to allow specifying an
internal PHYs layout. If field is not set, default layout is assumed (start
at port 0)
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure to use existing helper to get internal PHYs count instead of
redoing it manually
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since this function is a simple helper, we do not need to pass a full
dsa_switch structure, we can directly pass the mv88e6xxx_chip structure.
Doing so will allow to share this function with any other function
not manipulating dsa_switch structure but needing info about number of
internal phys
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no gpiod_export() and gpiod_unexport() looks pretty much stray.
The gpiod_export() and gpiod_unexport() shouldn't be used in the code,
GPIO sysfs is deprecated. That said, simply drop the stray call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230528142531.38602-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This update introduces specific register access boundaries for the
KSZ8873 and KSZ8863 chips within the DSA Microchip driver. The outlined
ranges target global control registers, port registers, and advanced
control registers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch prepares the ksz8863_smi part of ksz8 driver to utilize the
regmap register access validation feature.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The only place where this variable would be set to false is the
ksz8_config_cpu_port() function. But it is done in a bogus way:
for (i = 0; i < dev->phy_port_cnt; i++) {
if (i == dev->phy_port_cnt) <--- will be never executed.
break;
p->on = 1;
So, we never have a situation where p->on = 0. In this case, we can just
remove it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It is not immediately obvious that this driver allocates, via the
KSZ_REGMAP_TABLE() macro, 3 regmaps for register access: dev->regmap[0]
for 8-bit access, dev->regmap[1] for 16-bit and dev->regmap[2] for
32-bit access.
In future changes that add support for reg_fields, each field will have
to specify through which of the 3 regmaps it's going to go. Add an enum
now, to denote one of the 3 register access widths, and make the code go
through some wrapper functions for easier review and further
modification.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch refines the error handling mechanism for 8-bit register
read-modify-write operations. In case of a failure, it now logs an error
message detailing the problematic offset. This enhancement aids in
debugging by providing more precise information when these operations
encounter issues.
Furthermore, the ksz_prmw8() function has been updated to return error
values rather than void, enabling calling functions to appropriately
respond to errors.
Additionally, in case of an error that affects both the current and
future accesses, the PHY driver will log the errors consistently, akin
to the existing behavior in all ksz_read*/ksz_write* helpers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use the newly introduced lynx_pcs_create_mdiodev() which simplifies the
creation and destruction of the lynx PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the link forcing out of mac_config() and into the mac_prepare()
and mac_finish() methods. This results in no change to the order in
which these operations are performed, but does mean when we convert
mv88e6xxx to phylink_pcs support, we will continue to preserve this
ordering.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to datasheet, the command opcode must be specified
into bits [14:12] of the Extended Port Control register (EPC).
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marco Migliore <m.migliore@tiesse.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ports are in standalone mode, they should have learning disabled to
avoid adding new entries in the MAC lookup table which might be used by
other bridge ports to forward packets. While adding that, also make sure
learning is enabled for CPU port.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stp_set_state() should actually allow receiving BPDU while in LEARNING
mode which is not the case. Additionally, the BLOCKEN bit does not
actually forbid sending forwarded frames from that port. To fix this, add
a5psw_port_tx_enable() function which allows to disable TX. However, while
its name suggest that TX is totally disabled, it is not and can still
allow to send BPDUs even if disabled. This can be done by using forced
forwarding with the switch tagging mechanism but keeping "filtering"
disabled (which is already the case in the rzn1-a5sw tag driver). With
these fixes, STP support is now functional.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, management frame were discarded before reaching the CPU port due
to a misconfiguration of the MGMT_CONFIG register. Enable them by setting
the correct value in this register in order to correctly receive management
frame and handle STP.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On mt753x_cpu_port_enable() there's code that enables flooding for the CPU
port only. Since mt753x_cpu_port_enable() runs twice when both CPU ports
are enabled, port 6 becomes the only port to forward the frames to. But
port 5 is the active port, so no frames received from the user ports will
be forwarded to port 5 which breaks network connectivity.
Every bit of the BC_FFP, UNM_FFP, and UNU_FFP bits represents a port. Fix
this issue by setting the bit that corresponds to the CPU port without
overwriting the other bits.
Clear the bits beforehand only for the MT7531 switch. According to the
documents MT7621 Giga Switch Programming Guide v0.3 and MT7531 Reference
Manual for Development Board v1.0, after reset, the BC_FFP, UNM_FFP, and
UNU_FFP bits are set to 1 for MT7531, 0 for MT7530.
The commit 5e5502e012 ("net: dsa: mt7530: fix roaming from DSA user
ports") silently changed the method to set the bits on the MT7530_MFC.
Instead of clearing the relevant bits before mt7530_cpu_port_enable()
which runs under a for loop, the commit started doing it on
mt7530_cpu_port_enable().
Back then, this didn't really matter as only a single CPU port could be
used since the CPU port number was hardcoded. The driver was later changed
with commit 1f9a6abecf ("net: dsa: mt7530: get cpu-port via dp->cpu_dp
instead of constant") to retrieve the CPU port via dp->cpu_dp. With that,
this silent change became an issue for when using multiple CPU ports.
Fixes: 5e5502e012 ("net: dsa: mt7530: fix roaming from DSA user ports")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multi-chip module MT7530 switch with a 40 MHz oscillator on the
MT7621AT, MT7621DAT, and MT7621ST SoCs forwards corrupt frames using
trgmii.
This is caused by the assumption that MT7621 SoCs have got 150 MHz PLL,
hence using the ncpo1 value, 0x0780.
My testing shows this value works on Unielec U7621-06, Bartel's testing
shows it won't work on Hi-Link HLK-MT7621A and Netgear WAC104. All devices
tested have got 40 MHz oscillators.
Using the value for 125 MHz PLL, 0x0640, works on all boards at hand. The
definitions for 125 MHz PLL exist on the Banana Pi BPI-R2 BSP source code
whilst 150 MHz PLL don't.
Forwarding frames using trgmii on the MCM MT7530 switch with a 25 MHz
oscillator on the said MT7621 SoCs works fine because the ncpo1 value
defined for it is for 125 MHz PLL.
Change the 150 MHz PLL comment to 125 MHz PLL, and use the 125 MHz PLL
ncpo1 values for both oscillator frequencies.
Link: 81d24bbce7/u-boot-mt/drivers/net/rt2880_eth.c (L2195)
Fixes: 7ef6f6f8d2 ("net: dsa: mt7530: Add MT7621 TRGMII mode support")
Tested-by: Bartel Eerdekens <bartel.eerdekens@constell8.be>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rsvd2cpu capability for mv88e6321 model, to allow proper bpdu
processing.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Fixes: 51c901a775 ("net: dsa: mv88e6xxx: distinguish Global 2 Rsvd2CPU")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With LEDS_CLASS=m, a built-in qca8k driver fails to link:
arm-linux-gnueabi-ld: drivers/net/dsa/qca/qca8k-leds.o: in function `qca8k_setup_led_ctrl':
qca8k-leds.c:(.text+0x1ea): undefined reference to `devm_led_classdev_register_ext'
Change the dependency to avoid the broken configuration.
Fixes: 1e264f9d29 ("net: dsa: qca8k: add LEDs basic support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230420213639.2243388-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are two variants of the MT7531 switch IC which got different
features (and pins) regarding port 5:
* MT7531AE: SGMII/1000Base-X/2500Base-X SerDes PCS
* MT7531BE: RGMII
Moving the creation of the SerDes PCS from mt753x_setup to mt7530_probe
with commit 6de2852297 ("net: dsa: mt7530: move SGMII PCS creation
to mt7530_probe function") works fine for MT7531AE which got two
instances of mtk-pcs-lynxi, however, MT7531BE requires mt7531_pll_setup
to setup clocks before the single PCS on port 6 (usually used as CPU
port) starts to work and hence the PCS creation failed on MT7531BE.
Fix this by introducing a pointer to mt7531_create_sgmii function in
struct mt7530_priv and call it again at the end of mt753x_setup like it
was before commit 6de2852297 ("net: dsa: mt7530: move SGMII PCS
creation to mt7530_probe function").
Fixes: 6de2852297 ("net: dsa: mt7530: move SGMII PCS creation to mt7530_probe function")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/ZDvlLhhqheobUvOK@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because of the logic in place, SW_HUGE_PACKET can never be set.
(If the first condition is true, then the 2nd one is also true, but is not
executed)
Change the logic and update each bit individually.
Fixes: 29d1e85f45 ("net: dsa: microchip: ksz8: add MTU configuration support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/43107d9e8b5b8b05f0cbd4e1f47a2bb88c8747b2.1681755535.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add LEDs blink_set() support to qca8k Switch Family.
These LEDs support hw accellerated blinking at a fixed rate
of 4Hz.
Reject any other value since not supported by the LEDs switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LEDs basic support for qca8k Switch Family by adding basic
brightness_set() support.
Since these LEDs refelect port status, the default label is set to
":port". DT binding should describe the color and function of the
LEDs using standard LEDs api.
Each LED always have the device name as prefix. The device name is
composed from the mii bus id and the PHY addr resulting in example
names like:
- qca8k-0.0:00:amber:lan
- qca8k-0.0:00:white:lan
- qca8k-0.0:01:amber:lan
- qca8k-0.0:01:white:lan
These LEDs supports only blocking variant of the brightness_set()
function since they can sleep during access of the switch leds to set
the brightness.
While at it add to the qca8k header file each mode defined by the Switch
Documentation for future use.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move qca8k_port_to_phy() to qca8k header as it's useful for future
reference in Switch LEDs module since the same logic is applied to get
the right index of the switch port.
Make it inline as it's simple function that just decrease the port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to not transmit (preemptible) frames which will be received by
the link partner as corrupted (because it doesn't support FP), the
hardware requires the driver to program the QSYS_PREEMPTION_CFG_P_QUEUES
register only after the MAC Merge layer becomes active (verification
succeeds, or was disabled).
There are some cases when FP is known (through experimentation) to be
broken. Give priority to FP over cut-through switching, and disable FP
for known broken link modes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mqprio queue configuration can appear either through
TC_SETUP_QDISC_MQPRIO or through TC_SETUP_QDISC_TAPRIO. Make sure both
are treated in the same way.
Code does nothing new for now (except for rejecting multiple TXQs per
TC, which is a useless concept with DSA switches).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This doesn't apply anything to hardware and in general doesn't do
anything that the software variant doesn't do, except for checking that
there isn't more than 1 TXQ per TC (TXQs for a DSA switch are a dubious
concept anyway). The reason we add this is to be able to parse one more
field added to struct tc_mqprio_qopt_offload, namely preemptible_tcs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the switch emits an IRQ, we don't know what caused it, and we
iterate through all ports to check the MAC Merge status.
Move that iteration inside the ocelot lib; we will change the locking in
a future change and it would be good to encapsulate that lock completely
within the ocelot lib.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
That comment was written prior to knowing that what I was actually
seeing was a manifestation of the bug fixed in commit b4024c9e5c
("felix: Fix initialization of ioremap resources").
There isn't any particular reason now why the hardware initialization is
done in felix_setup(), so just delete that comment to avoid spreading
misinformation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch can either take the MAC or the PHY role in an MII or RMII
link. There are distinct PHY_INTERFACE_ macros for these two roles.
Correct the mapping so that the `REV` version is used for the PHY
role.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230411023541.2372609-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To handle potential read/write operation failures, update
ksz8_w_sta_mac_table() to make use of the return values provided by
read/write functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since ksz8_w_sta_mac_table() is only used within ksz8795.c, make it static
to limit its scope.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Take advantage of the return values provided by read/write functions in
ksz8_r_sta_mac_table() to handle cases where read/write operations may
fail.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Prepare for the next patch by ensuring that ksz8_r_sta_mac_table() does
not use error codes for empty entries. This change will enable better
handling of read/write errors in the upcoming patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As ksz8_r_sta_mac_table() is only used within ksz8795.c, there is no need
to export it. Make the function static for better encapsulation.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for add/del_fdb operations and utilize the refactored static
MAC table code. This resolves kernel warnings caused by the lack of fdb
add function support in the current driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Move static MAC table operations to separate functions in order to reuse
the code for add/del_fdb. This is needed to address kernel warnings
caused by the lack of fdb add function support in the current driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add driver for the built-in Gigabit Ethernet switch which can be found
in the MediaTek MT7988 SoC.
The switch shares most of its design with MT7530 and MT7531, but has
it's registers mapped into the SoCs register space rather than being
connected externally or internally via MDIO.
Introduce a new platform driver to support that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As MT7530 and MT7531 internally use 32-bit wide registers, each access
to any register of the switch requires several operations on the MDIO
bus. Hence if there is congruent access, e.g. due to PCS or PHY
polling, this can mess up and interfere with another ongoing register
access sequence.
However, the MDIO bus mutex is only relevant for MDIO-connected
switches. Prepare switches which have there registers directly mapped
into the SoCs register space via MMIO which do not require such
locking. There we can simply use regmap's default locking mechanism.
Hence guard mutex operations to only be performed in case of MDIO
connected switches.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split MT7530 switch driver into a common part and a part specific
for MDIO connected switches and multi-chip modules.
Move MDIO-specific functions to newly introduced mt7530-mdio.c while
keeping the common parts in mt7530.c.
Introduce new Kconfig symbol CONFIG_NET_DSA_MT7530_MDIO which is
implied by CONFIG_NET_DSA_MT7530.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
MT7988 shares a significant part of the setup function with MT7531.
Split-off those parts into a shared function which is going to be used
also by mt7988_setup.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move commonly used parts from mt7530_remove into new
mt7530_remove_common helper function which will be used by both,
mt7530_remove and the to-be-introduced mt7988_remove.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move commonly used parts from mt7530_probe into new mt7530_probe_common
helper function which will be used by both, mt7530_probe and the
to-be-introduced mt7988_probe.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of splitting mt7530.c into a driver for MDIO-connected
as well as MDIO-accessed built-in switches on one hand and MMIO-accessed
built-in switches move the p5_inft_modes() function from mt7530.h to
mt7530.c. The function is only needed there and will trigger a compiler
warning about a defined but unused function otherwise when including
mt7530.h in the to-be-introduced bus-specific drivers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the MDIO bus lock only needs to be involved if actually operating
on an MDIO-connected switch we will need to skip locking for built-in
switches which are accessed via MMIO.
Create helper functions which simplify that upcoming change.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move creating the SGMII PCS from mt753x_setup() to the more appropriate
mt7530_probe() function.
This is done also in preparation of moving all functions related to
MDIO-connected MT753x switches to a separate module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use regmap API to access the switch register space.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of wrapping the locked register accessor functions, use the
unlocked variants and add locking wrapper functions to let regmap
handle the locking.
This is a preparation towards being able to always use regmap to
access switch registers instead of open-coded accessor functions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of macro templates use a dedidated function and allocated
regmap_config when creating the regmaps for the pcs-mtk-lynxi
instances.
This is in preparation to switching to use unlocked regmap accessors
and have regmap's locking API handle locking for us.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simply returning the negative error value instead of the read value
doesn't seem like a good idea. Return 0 instead and add WARN_ON_ONCE(1)
so this kind of error will not go unnoticed.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The force watchdog event bit is not cleared during SW reset in the
mv88e6393x switch. This is a different behavior compared to mv886390 which
clears the force WD event bit as advertised. This causes a force WD event
to be handled over and over again as the SW reset following the event never
clears the force WD event bit.
Explicitly clear the watchdog event register to 0 in irq_action when
handling an event to prevent the switch from sending continuous interrupts.
Marvell aren't aware of any other stuck bits apart from the force WD
bit.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family"
Signed-off-by: Gustav Ekelund <gustaek@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Do not set the MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP bit on CPU or DSA ports.
This allows the host CPU port to be a regular IGMP listener by sending out
IGMP Membership Reports, which would otherwise not be forwarded by the
mv88exxx chip, but directly looped back to the CPU port itself.
Fixes: 54d792f257 ("net: dsa: Centralise global and port setup code into mv88e6xxx.")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230329150140.701559-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement phy_read16() and phy_write16() ops for B53 MMAP to avoid accessing
B53_PORT_MII_PAGE registers which hangs the device.
This access should be done through the MDIO Mux bus controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the BCM53134 Ethernet switch in the existing b53 dsa driver.
BCM53134 is very similar to the BCM58XX series.
Signed-off-by: Paul Geurts <paul.geurts@prodrive-technologies.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FID is directly mapped to VID. However, configuring a MAC address with a
VID != 0 resulted in incorrect configuration due to an incorrect bit
mask. This kernel commit fixed the issue by correcting the bit mask and
ensuring proper configuration of MAC addresses with non-zero VID.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current regmap bulk access is broken, resulting to wrong reads/writes
if ksz_read64/ksz_write64 functions are used.
Mostly this issue was visible by using ksz8_fdb_dump(), which returned
corrupt MAC address.
The reason is that regmap was configured to have max_raw_read/write,
even if ksz8863_mdio_read/write functions are able to handle unlimited
read/write accesses. On ksz_read64 function we are using multiple 32bit
accesses by incrementing each access by 1 instead of 4. Resulting buffer
had 01234567.12345678 instead of 01234567.89abcdef.
We have multiple ways to fix it:
- enable 4 byte alignment for 32bit accesses. Since the HW do not have
this requirement. It will break driver.
- disable max_raw_* limit.
This patch is removing max_raw_* limit for regmap accesses in ksz8863_smi.
Fixes: 60a3647600 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the dynamic MAC table is empty, we will still extract one outdated
entry. Fix it by using correct bit offset.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are using wrong offset, so we will get not a timestamp.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current ksz8_fdb_dump() is able to extract only max 249 entries on
the ksz8863/ksz8873 series of switches. This happened due to wrong
bit mask and offset calculation.
This commit corrects the issue and allows for the complete extraction of
all 1024 entries.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch, the ksz8_fdb_dump() function had several issues, such
as uninitialized variables and incorrect usage of source port as a bit
mask. These problems caused inaccurate reporting of vid information and
port assignment in the bridge fdb.
Fixes: e587be759e ("net: dsa: microchip: update fdb add/del/dump in ksz_common")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The probe function sets priv->chip_data to (void *)priv + sizeof(*priv)
with the expectation that priv has enough trailing space.
However, only realtek-smi actually allocated this chip_data space.
Do likewise in realtek-mdio to fix out-of-bounds accesses.
These accesses likely went unnoticed so far, because of an (unused)
buf[4096] member in struct realtek_priv, which caused kmalloc to
round up the allocated buffer to a big enough size, so nothing of
value was overwritten. With a different allocator (like in the barebox
bootloader port of the driver) or with KASAN, the memory corruption
becomes quickly apparent.
Fixes: aac9400106 ("net: dsa: realtek: add new mdio interface for drivers")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20230323103735.2331786-1-a.fatoum@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move setting the ssc_delta variable to under the PHY_INTERFACE_MODE_TRGMII
case as it's only needed when trgmii is used.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230320190520.124513-3-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move lowering the TRGMII Tx clock driving to mt7530_setup(), after setting
the core clock, as seen on the U-Boot MediaTek ethernet driver.
Move the code which looks like it lowers the TRGMII Rx clock driving to
after the TRGMII Tx clock driving is lowered. This is run after lowering
the Tx clock driving on the U-Boot MediaTek ethernet driver as well.
This way, the switch should consume less power regardless of port 6 being
used.
Update the comment explaining mt7530_pad_clk_setup().
Tested rgmii and trgmii modes of port 6 and rgmii mode of port 5 on MCM
MT7530 on MT7621AT Unielec U7621-06 and standalone MT7530 on MT7623NI
Bananapi BPI-R2.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Link: 29a48bf9cc/drivers/net/mtk_eth.c (L682)
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230320190520.124513-2-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Split the code that enables and disables TRGMII clocks and core clock.
Move enabling and disabling core clock to mt7530_pll_setup() as it's
supposed to be run there.
Add 20 ms delay before enabling the core clock as seen on the U-Boot
MediaTek ethernet driver.
Change the comment for enabling and disabling TRGMII clocks as the code
seems to affect both TXC and RXC.
Tested rgmii and trgmii modes of port 6 and rgmii mode of port 5 on MCM
MT7530 on MT7621AT Unielec U7621-06 and standalone MT7530 on MT7623NI
Bananapi BPI-R2.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Link: 29a48bf9cc/drivers/net/mtk_eth.c (L589)
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230320190520.124513-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM6318 and BCM63268 SoCs require a special handling for their RGMIIs, so we
should be able to identify them as a special BCM63xx switch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM6318, BCM6362 and BCM63268 are SoCs with a B53 MMAP switch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM63xx RGMII ports require additional configuration in order to work.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230319220805.124024-1-noltari@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
pcs_get_state() implementations are not supposed to alter an_enabled.
Remove this assignment.
Fixes: b3591c2a36 ("net: dsa: qca8k: Switch to PHYLINK instead of PHYLIB")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1pdsE5-00Dl2l-8F@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit 2c7e46edbd ("net: dsa: mv88e6xxx: mask apparently non-existing
phys during probing") added non-trivial bus->phy_mask in
mv88e6xxx_mdio_register() in order to avoid excessive mdio bus
transactions during probing.
But the mask is incorrect for switches with non-zero phy_base_addr (such
as 88E6341).
Fix this.
Fixes: 2c7e46edbd ("net: dsa: mv88e6xxx: mask apparently non-existing phys during probing")
Signed-off-by: Marek Behún <kabel@kernel.org>
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230319140238.9470-1-kabel@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Implement regmap access wrappers, for now only to be used by the
pcs-mtk-lynxi driver.
Make use of this external PCS driver and drop the now reduntant
implementation in mt7530.c.
As a nice side effect the SGMII registers can now also more easily be
inspected for debugging via /sys/kernel/debug/regmap.
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VSC7512 has four ports with internal phys that are already supported.
There are additional ports that can be configured to work with external
phys.
Add support for these additional ethernet ports.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ports for Ocelot devices (VSC7511, VSC7512, VSC7513 and VSC7514) support
external phys. When external phys are used, additional configuration on
each port is required to enable QSGMII mode and set external phy modes.
Add a configurable hook into these routines, so the external ports can be
used.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a user of the Felix driver has a port running in SGMII / QSGMII mode, it
will need to utilize phylink_mac_config(). Add this configurability.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC7512 and VSC7514 have internal PLLs that can be used to control
different peripherals. Initialize these high speed I/O (HSIO) PLLs when
they exist, so that dependent peripherals like QSGMII can function.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid excessive mdio bus transactions during probing, mask all phy
addresses that do not exist (there is a 1:1 mapping between switch port
number and phy address).
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Call the rather expensive mv88e6xxx_mdios_register() at the beginning of
mv88e6xxx_setup(). This avoids the double call via mv88e6xxx_probe()
during boot.
For symmetry, call mv88e6xxx_mdios_unregister() at the end of
mv88e6xxx_teardown().
Link: https://lore.kernel.org/lkml/449bde236c08d5ab5e54abd73b645d8b29955894.camel@gmail.com/
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move mv88e6xxx_setup() below mv88e6xxx_mdios_register(), so that we are
able to call the latter one from here. Do the same thing for the
inverse functions.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
irq_find_mapping() does not need irq_dispose_mapping(), only
irq_create_mapping() does.
Calling irq_dispose_mapping() from mv88e6xxx_g2_irq_mdio_free() and from
the error path of mv88e6xxx_g2_irq_mdio_setup() effectively means that
the mdiobus logic (for internal PHY interrupts) is disposing of a
hwirq->virq mapping which it is not responsible of (but instead, the
function pair mv88e6xxx_g2_irq_setup() + mv88e6xxx_g2_irq_free() is).
With the current code structure, this isn't such a huge problem, because
mv88e6xxx_g2_irq_mdio_free() is called relatively close to the real
owner of the IRQ mappings:
mv88e6xxx_remove()
-> mv88e6xxx_unregister_switch()
-> mv88e6xxx_mdios_unregister()
-> mv88e6xxx_g2_irq_mdio_free()
-> mv88e6xxx_g2_irq_free()
and the switch isn't 'live' in any way such that it would be able of
generating interrupts at this point (mv88e6xxx_unregister_switch() has
been called).
However, there is a desire to split mv88e6xxx_mdios_unregister() and
mv88e6xxx_g2_irq_free() such that mv88e6xxx_mdios_unregister() only gets
called from mv88e6xxx_teardown(). This is much more problematic, as can
be seen below.
In a cross-chip scenario (say 3 switches d0032004.mdio-mii:10,
d0032004.mdio-mii:11 and d0032004.mdio-mii:12 which form a single DSA
tree), it is possible to unbind the device driver from a single switch
(say d0032004.mdio-mii:10).
When that happens, mv88e6xxx_remove() will be called for just that one
switch, and this will call mv88e6xxx_unregister_switch() which will tear
down the entire tree (calling mv88e6xxx_teardown() for all 3 switches).
Assuming mv88e6xxx_mdios_unregister() was moved to mv88e6xxx_teardown(),
at this stage, all 3 switches will have called irq_dispose_mapping() on
their mdiobus virqs.
When we bind again the device driver to d0032004.mdio-mii:10,
mv88e6xxx_probe() is called for it, which calls dsa_register_switch().
The DSA tree is now complete again, and mv88e6xxx_setup() is called for
all 3 switches.
Also assuming that mv88e6xxx_mdios_register() is moved to
mv88e6xxx_setup() (the 2 assumptions go together), at this point,
d0032004.mdio-mii:11 and d0032004.mdio-mii:12 don't have an IRQ mapping
for the internal PHYs anymore, as they've disposed of it in
mv88e6xxx_teardown(). Whereas switch d0032004.mdio-mii:10 has re-created
it, because its code path comes from mv88e6xxx_probe().
Simply put, this change prepares the driver to handle the movement of
mv88e6xxx_mdios_register() to mv88e6xxx_setup() for cross-chip DSA trees.
Also, the code being deleted was partially wrong anyway (in a way which
may have hidden this other issue). mv88e6xxx_g2_irq_mdio_setup()
populates bus->irq[] starting with offset chip->info->phy_base_addr, but
the teardown path doesn't apply that offset too. So it disposes of virq
0 for phy = [ 0, phy_base_addr ).
All switch families have phy_base_addr = 0, except for MV88E6141 and
MV88E6341 which have it as 0x10. I guess those families would have
happened to work by mistake in cross-chip scenarios too.
I'm deleting the body of mv88e6xxx_g2_irq_mdio_free() but leaving its
call sites and prototype in place. This is because, if we ever need to
add back some teardown procedure in the future, it will be perhaps
error-prone to deduce the proper call sites again. Whereas like this,
no extra code should get generated, it shouldn't bother anybody.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CPU port should also be enabled in order to get a working switch.
Fixes: a5538a777b ("net: dsa: b53: mmap: Add device tree support")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230316172807.460146-1-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rtl8365mb was using a fixed MTU size of 1536, which was probably
inspired by the rtl8366rb's initial frame size. However, unlike that
family, the rtl8365mb family can specify the max frame size in bytes,
rather than in fixed steps.
DSA calls change_mtu for the CPU port once the max MTU value among the
ports changes. As the max frame size is defined globally, the switch
is configured only when the call affects the CPU port.
The available specifications do not directly define the max supported
frame size, but it mentions a 16k limit. This driver will use the 0x3FFF
limit as it is used in the vendor API code. However, the switch sets the
max frame size to 16368 bytes (0x3FF0) after it resets.
change_mtu uses MTU size, or ethernet payload size, while the switch
works with frame size. The frame size is calculated considering the
ethernet header (14 bytes), a possible 802.1Q tag (4 bytes), the payload
size (MTU), and the Ethernet FCS (4 bytes). The CPU tag (8 bytes) is
consumed before the switch enforces the limit.
During setup, the driver will use the default 1500-byte MTU of DSA to
set the maximum frame size. The current sum will be
VLAN_ETH_HLEN+1500+ETH_FCS_LEN, which results in 1522 bytes. Although
it is lower than the previous initial value of 1536 bytes, the driver
will increase the frame size for a larger MTU. However, if something
requires more space without increasing the MTU, such as QinQ, we would
need to add the extra length to the rtl8365mb_port_change_mtu() formula.
MTU was tested up to 2018 (with 802.1Q) as that is as far as mt7620
(where rtl8367s is stacked) can go. The register was manually
manipulated byte-by-byte to ensure the MTU to frame size conversion was
correct. For frames without 802.1Q tag, the frame size limit will be 4
bytes over the required size.
There is a jumbo register, enabled by default at 6k frame size.
However, the jumbo settings do not seem to limit nor expand the maximum
tested MTU (2018), even when jumbo is disabled. More tests are needed
with a device that can handle larger frames.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit has replaced a ksz_write8() call to address
REG_PORT_5_CTRL_6 (0x56) with a ksz_set_xmii() -> ksz_pwrite8() call to
regs[P_XMII_CTRL_1], which is also defined as 0x56 for ksz8795_regs[].
The trouble is that, when compared to ksz_write8(), ksz_pwrite8() also
adjusts the register offset with the port base address. So in reality,
ksz_pwrite8(offset=0x56) accesses register 0x56 + 0x50 = 0xa6, which in
this switch appears to be unmapped, and the RGMII delay configuration on
the CPU port does nothing.
So if the switch wasn't fine with the RGMII delay configuration done
through pin strapping and relied on Linux to apply a different one in
order to pass traffic, this is now broken.
Using the offset translation logic imposed by ksz_pwrite8(), the correct
value for regs[P_XMII_CTRL_1] should have been 0x6 on ksz8795_regs[], in
order to really end up accessing register 0x56.
Static code analysis shows that, despite there being multiple other
accesses to regs[P_XMII_CTRL_1] in this driver, the only code path that
is applicable to ksz8795_regs[] and ksz8_dev_ops is ksz_set_xmii().
Therefore, the problem is isolated to RGMII delays.
In its current form, ksz8795_regs[] contains the same value for
P_XMII_CTRL_0 and for P_XMII_CTRL_1, and this raises valid suspicions
that writes made by the driver to regs[P_XMII_CTRL_0] might overwrite
writes made to regs[P_XMII_CTRL_1] or vice versa.
Again, static analysis shows that the only accesses to P_XMII_CTRL_0
from the driver are made from code paths which are not reachable with
ksz8_dev_ops. So the accesses made by ksz_set_xmii() are safe for this
switch family.
[ vladimiroltean: rewrote commit message ]
Fixes: c476bede4b ("net: dsa: microchip: ksz8795: use common xmii function")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230315231916.2998480-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://lore.kernel.org/r/20230314181824.56881-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are 3 classes of switch families that the driver is aware of, as
far as mv88e6xxx_change_mtu() is concerned:
- MTU configuration is available per port. Here, the
chip->info->ops->port_set_jumbo_size() method will be present.
- MTU configuration is global to the switch. Here, the
chip->info->ops->set_max_frame_size() method will be present.
- We don't know how to change the MTU. Here, none of the above methods
will be present.
Switch families MV88E6165, MV88E6191, MV88E6220, MV88E6250 and MV88E6290
fall in category 3.
The blamed commit has adjusted the MTU for all 3 categories by EDSA_HLEN
(8 bytes), resulting in a new maximum MTU of 1492 being reported by the
driver for these switches.
I don't have the hardware to test, but I do have a MV88E6390 switch on
which I can simulate this by commenting out its .port_set_jumbo_size
definition from mv88e6390_ops. The result is this set of messages at
probe time:
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 1
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 2
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 3
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 4
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 5
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 6
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 7
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 8
It is highly implausible that there exist Ethernet switches which don't
support the standard MTU of 1500 octets, and this is what the DSA
framework says as well - the error comes from dsa_slave_create() ->
dsa_slave_change_mtu(slave_dev, ETH_DATA_LEN).
But the error messages are alarming, and it would be good to suppress
them.
As a consequence of this unlikeliness, we reimplement mv88e6xxx_get_max_mtu()
and mv88e6xxx_change_mtu() on switches from the 3rd category as follows:
the maximum supported MTU is 1500, and any request to set the MTU to a
value larger than that fails in dev_validate_mtu().
Fixes: b9c587fed6 ("dsa: mv88e6xxx: Include tagger overhead when setting MTU for DSA and CPU ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/net/dsa/ocelot/ocelot_ext.c:143:34: error: ‘ocelot_ext_switch_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
drivers/net/dsa/microchip/ksz9477_i2c.c:84:34: error: ‘ksz9477_dt_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/net/dsa/ocelot/seville_vsc9953.c:1070:34: error: ‘seville_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will match mostly or only by DT table (even thought there is
regular ID table) so there is little benefit in of_match_ptr (this also
allows ACPI matching via PRP0001, even though it might not be relevant
here).
drivers/net/dsa/lan9303_i2c.c:97:34: error: ‘lan9303_i2c_of_match’ defined but not used [-Werror=unused-const-variable=]
drivers/net/dsa/lan9303_mdio.c:157:34: error: ‘lan9303_mdio_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/net/dsa/lantiq_gswip.c:1888:34: error: ‘xway_gphy_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ETS Qdisc support for KSZ9477 of switches. Current implementation is
limited to strict priority mode.
Tested on KSZ8563R with following configuration:
tc qdisc replace dev lan2 root handle 1: ets strict 4 \
priomap 3 3 2 2 1 1 0 0
ip link add link lan2 name v1 type vlan id 1 \
egress-qos-map 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7
and patched iperf3 version:
https://github.com/esnet/iperf/pull/1476
iperf3 -c 172.17.0.1 -b100M -l1472 -t100 -u -R --sock-prio 2
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ksz_setup_tc_mode() to make queue scheduling and shaping
configuration more visible.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As my testing on the MCM MT7530 switch on MT7621 SoC shows, setting the PLL
frequency does not affect MII modes other than trgmii on port 5 and port 6.
So the assumption is that the operation here called "setting the PLL
frequency" actually sets the frequency of the TRGMII TX clock.
Make it so that it and the rest of the trgmii setup run only when the
trgmii mode is used.
Tested rgmii and trgmii modes of port 6 on MCM MT7530 on MT7621AT Unielec
U7621-06 and standalone MT7530 on MT7623NI Bananapi BPI-R2.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230310073338.5836-2-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove now incorrect comment regarding port 5 as GMAC5. This is supposed to
be supported since commit 38f790a805 ("net: dsa: mt7530: Add support for
port 5") under mt7530_setup_port5().
Fixes: 38f790a805 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230310073338.5836-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MT7530 switch from the MT7621 SoC has 2 ports which can be set up as
internal: port 5 and 6. Arınç reports that the GMAC1 attached to port 5
receives corrupted frames, unless port 6 (attached to GMAC0) has been
brought up by the driver. This is true regardless of whether port 5 is
used as a user port or as a CPU port (carrying DSA tags).
Offline debugging (blind for me) which began in the linked thread showed
experimentally that the configuration done by the driver for port 6
contains a step which is needed by port 5 as well - the write to
CORE_GSWPLL_GRP2 (note that I've no idea as to what it does, apart from
the comment "Set core clock into 500Mhz"). Prints put by Arınç show that
the reset value of CORE_GSWPLL_GRP2 is RG_GSWPLL_POSDIV_500M(1) |
RG_GSWPLL_FBKDIV_500M(40) (0x128), both on the MCM MT7530 from the
MT7621 SoC, as well as on the standalone MT7530 from MT7623NI Bananapi
BPI-R2. Apparently, port 5 on the standalone MT7530 can work under both
values of the register, while on the MT7621 SoC it cannot.
The call path that triggers the register write is:
mt753x_phylink_mac_config() for port 6
-> mt753x_pad_setup()
-> mt7530_pad_clk_setup()
so this fully explains the behavior noticed by Arınç, that bringing port
6 up is necessary.
The simplest fix for the problem is to extract the register writes which
are needed for both port 5 and 6 into a common mt7530_pll_setup()
function, which is called at mt7530_setup() time, immediately after
switch reset. We can argue that this mirrors the code layout introduced
in mt7531_setup() by commit 42bc4fafe3 ("net: mt7531: only do PLL once
after the reset"), in that the PLL setup has the exact same positioning,
and further work to consolidate the separate setup() functions is not
hindered.
Testing confirms that:
- the slight reordering of writes to MT7530_P6ECR and to
CORE_GSWPLL_GRP1 / CORE_GSWPLL_GRP2 introduced by this change does not
appear to cause problems for the operation of port 6 on MT7621 and on
MT7623 (where port 5 also always worked)
- packets sent through port 5 are not corrupted anymore, regardless of
whether port 6 is enabled by phylink or not (or even present in the
device tree)
My algorithm for determining the Fixes: tag is as follows. Testing shows
that some logic from mt7530_pad_clk_setup() is needed even for port 5.
Prior to commit ca366d6c88 ("net: dsa: mt7530: Convert to PHYLINK
API"), a call did exist for all phy_is_pseudo_fixed_link() ports - so
port 5 included. That commit replaced it with a temporary "Port 5 is not
supported!" comment, and the following commit 38f790a805 ("net: dsa:
mt7530: Add support for port 5") replaced that comment with a
configuration procedure in mt7530_setup_port5() which was insufficient
for port 5 to work. I'm laying the blame on the patch that claimed
support for port 5, although one would have also needed the change from
commit c3b8e07909 ("net: dsa: mt7530: setup core clock even in TRGMII
mode") for the write to be performed completely independently from port
6's configuration.
Thanks go to Arınç for describing the problem, for debugging and for
testing.
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/netdev/f297c2c4-6e7c-57ac-2394-f6025d309b9d@arinc9.com/
Fixes: 38f790a805 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230307155411.868573-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During review of ocelot_ext, it created a private phylink instance
that wasn't necessary. This was removed for subsequent postings,
but the include file seems to have been left behind. Remove it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compiling a kernel which has both CONFIG_NET_DSA_MSCC_OCELOT_EXT
and CONFIG_MSCC_OCELOT_SWITCH enabled, the following error message will
be printed:
[ 5.266588] Error: Driver 'ocelot-switch' is already registered, aborting...
Rename the ocelot_ext.c driver to "ocelot-ext-switch" to avoid the name
duplication, and update the mfd_cell entry for its resources.
Fixes: 3d7316ac81 ("net: dsa: ocelot: add external ocelot switch control")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit did not properly convert the resource start/end format
into the DEFINE_RES_MEM_NAMED() start/length format, resulting in a
resource for vsc9959_imdio_res which is much longer than expected:
$ cat /proc/iomem
1f8000000-1f815ffff : pcie@1f0000000
1f8140000-1f815ffff : 0000:00:00.5
1f8148030-1f815006f : imdio
vs (correct)
$ cat /proc/iomem
1f8000000-1f815ffff : pcie@1f0000000
1f8140000-1f815ffff : 0000:00:00.5
1f8148030-1f814803f : imdio
Luckily it's not big enough to exceed the size of the parent resource
(pci_resource_end(pdev, VSC9959_IMDIO_PCI_BAR)), and it doesn't overlap
with anything else that the Linux driver uses currently, so the larger
than expected size isn't a practical problem that I can see. Although it
is clearly wrong in the /proc/iomem output.
Fixes: 044d447a80 ("net: dsa: felix: use DEFINE_RES_MEM_NAMED for resources")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the refactoring in the commit below, vsc9953_mdio_read() was
replaced with mscc_miim_read(), which has one extra step: it checks for
the MSCC_MIIM_DATA_ERROR bits before returning the result.
On T1040RDB, there are 8 QSGMII PCSes belonging to the switch, and they
are organized in 2 groups. First group responds to MDIO addresses 4-7
because QSGMIIACR1[MDEV_PORT] is 1, and the second group responds to
MDIO addresses 8-11 because QSGMIIBCR1[MDEV_PORT] is 2. I have double
checked that these values are correctly set in the SERDES, as well as
PCCR1[QSGMA_CFG] and PCCR1[QSGMB_CFG] are both 0b01.
mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 4 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 4 reg 0x5 MIIM_DATA 0x3da01, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR
As can be seen, the data in MIIM_DATA is still valid despite having the
MSCC_MIIM_DATA_ERROR bits set. The driver as introduced in commit
84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953
switch") was ignoring these bits, perhaps deliberately (although
unbeknownst to me).
This is an old IP and the hardware team cannot seem to be able to help
me track down a plausible reason for these failures. I'll keep
investigating, but in the meantime, this is a direct regression which
must be restored to a working state.
The only thing I can do is keep ignoring the errors as before.
Fixes: b996584523 ("net: dsa: ocelot: felix: utilize shared mscc-miim driver for indirect MDIO access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of KSZ9477 family switches provides EEE support. To enable it, we
just need to register set_mac_eee/set_mac_eee handlers and validate
supported chip version and port.
Currently supported chip variants are: KSZ8563, KSZ9477, KSZ9563,
KSZ9567, KSZ9893, KSZ9896, KSZ9897. KSZ8563 supports EEE only with
100BaseTX/Full. Other chips support 100BaseTX/Full and 1000BaseTX/Full.
Low Power Idle configuration is not supported and currently not
documented in the datasheets.
EEE PHY specific tunings are not documented in the switch datasheets, but can
overlap with KSZ9131 specification.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new user of MSCC_OCELOT_SWITCH_LIB was added, bringing back an old
link failure that was fixed with e5f3155267 ("ethernet: fix
PTP_1588_CLOCK dependencies"):
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_ptp_enable':
ocelot_ptp.c:(.text+0x8ee): undefined reference to `ptp_find_pin'
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_get_ts_info':
ocelot_ptp.c:(.text+0xd5d): undefined reference to `ptp_clock_index'
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_init_timestamp':
ocelot_ptp.c:(.text+0x15ca): undefined reference to `ptp_clock_register'
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_deinit_timestamp':
ocelot_ptp.c:(.text+0x16b7): undefined reference to `ptp_clock_unregister'
Add the same PTP dependency here, as well as in the MSCC_OCELOT_SWITCH_LIB
symbol itself to make it more obvious what is going on when the next
driver selects it.
Fixes: 3d7316ac81 ("net: dsa: ocelot: add external ocelot switch control")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20230209124435.1317781-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Frank reports that in a mt7530 setup where some ports are standalone and
some are in a VLAN-aware bridge, 8021q uppers of the standalone ports
lose their VLAN tag on xmit, as seen by the link partner.
This seems to occur because once the other ports join the VLAN-aware
bridge, mt7530_port_vlan_filtering() also calls
mt7530_port_set_vlan_aware(ds, cpu_dp->index), and this affects the way
that the switch processes the traffic of the standalone port.
Relevant is the PVC_EG_TAG bit. The MT7530 documentation says about it:
EG_TAG: Incoming Port Egress Tag VLAN Attribution
0: disabled (system default)
1: consistent (keep the original ingress tag attribute)
My interpretation is that this setting applies on the ingress port, and
"disabled" is basically the normal behavior, where the egress tag format
of the packet (tagged or untagged) is decided by the VLAN table
(MT7530_VLAN_EGRESS_UNTAG or MT7530_VLAN_EGRESS_TAG).
But there is also an option of overriding the system default behavior,
and for the egress tagging format of packets to be decided not by the
VLAN table, but simply by copying the ingress tag format (if ingress was
tagged, egress is tagged; if ingress was untagged, egress is untagged;
aka "consistent). This is useful in 2 scenarios:
- VLAN-unaware bridge ports will always encounter a miss in the VLAN
table. They should forward a packet as-is, though. So we use
"consistent" there. See commit e045124e93 ("net: dsa: mt7530: fix
tagged frames pass-through in VLAN-unaware mode").
- Traffic injected from the CPU port. The operating system is in god
mode; if it wants a packet to exit as VLAN-tagged, it sends it as
VLAN-tagged. Otherwise it sends it as VLAN-untagged*.
*This is true only if we don't consider the bridge TX forwarding offload
feature, which mt7530 doesn't support.
So for now, make the CPU port always stay in "consistent" mode to allow
software VLANs to be forwarded to their egress ports with the VLAN tag
intact, and not stripped.
Link: https://lore.kernel.org/netdev/trinity-e6294d28-636c-4c40-bb8b-b523521b00be-1674233135062@3c-app-gmx-bs36/
Fixes: e045124e93 ("net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230205140713.1609281-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When NET_DSA_MICROCHIP_KSZ_COMMON is built-in but PTP is a loadable
module, the ksz_ptp support still causes a link failure:
ld.lld-16: error: undefined symbol: ptp_clock_index
>>> referenced by ksz_ptp.c
>>> drivers/net/dsa/microchip/ksz_ptp.o:(ksz_get_ts_info) in archive vmlinux.a
This can happen if NET_DSA_MICROCHIP_KSZ8863_SMI is enabled, or
even if none of the KSZ9477_I2C/KSZ_SPI/KSZ8863_SMI ones are active
but only the common module is.
The most straightforward way to address this is to move the
dependency to NET_DSA_MICROCHIP_KSZ_PTP itself, which can now
only be enabled if both PTP_1588_CLOCK support is reachable
from NET_DSA_MICROCHIP_KSZ_COMMON. Alternatively, one could make
NET_DSA_MICROCHIP_KSZ_COMMON a hidden Kconfig symbol and extend the
PTP_1588_CLOCK_OPTIONAL dependency to NET_DSA_MICROCHIP_KSZ8863_SMI as
well, but that is a little more fragile.
Fixes: eac1ea2026 ("net: dsa: microchip: ptp: add the posix clock support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230130131808.1084796-1-arnd@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add control of an external VSC7512 chip.
Currently the four copper phy ports are fully functional. Communication to
external phys is also functional, but the SGMII / QSGMII interfaces are
currently non-functional.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the Felix driver would probe the ports and verify functionality, it
would fail if it hit single port mode that wasn't supported by the driver.
The initial case for the VSC7512 driver will have physical ports that
exist, but aren't supported by the driver implementation. Add the
OCELOT_PORT_MODE_NONE macro to handle this scenario, and allow the Felix
driver to continue with all the ports that are currently functional.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The architecture around the VSC7512 differs from existing felix drivers. In
order to add support for all the chip's features (pinctrl, MDIO, gpio) the
device had to be laid out as a multi-function device (MFD).
One difference between an MFD and a standard platform device is that the
regmaps are allocated to the parent device before the child devices are
probed. As such, there is no need for felix to initialize new regmaps in
these configurations, they can simply be requested from the parent device.
Add support for MFD configurations by performing this request from the
parent device.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The define FELIX_MAC_QUIRKS was used directly in the felix.c shared driver.
Other devices (VSC7512 for example) don't require the same quirks, so they
need to be configured on a per-device basis.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert qca8k to regmap read/write bulk API. The mgmt eth can write up
to 32 bytes of data at times. Currently we use a custom function to do
it but regmap now supports declaration of read/write bulk even without a
bus.
Drop the custom function and rework the regmap function to this new
implementation.
Rework the qca8k_fdb_read/write function to use the new
regmap_bulk_read/write as the old qca8k_bulk_read/write are now dropped.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and use QCA8K_ATU_TABLE_SIZE instead of hardcoding the ATU size with
a pure number and using sizeof on the array.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The build system currently complains:
scripts/Makefile.build:252: drivers/net/dsa/ocelot/Makefile:
felix.o is added to multiple modules: mscc_felix mscc_seville
Since felix.c holds the DSA glue layer, create a mscc_felix_dsa_lib.ko.
This is similar to how mscc_ocelot_switch_lib.ko holds a library for
configuring the hardware.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20230125145716.271355-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KSZ9477, KSZ9567, KSZ9563, KSZ8563 and LAN937x supports Credit based
shaper. To differentiate the chip supporting cbs, tc_cbs_supported
flag is introduced in ksz_chip_data.
And KSZ series has 16bit Credit increment registers whereas LAN937x has
24bit register. The value to be programmed in the credit increment is
determined using the successive multiplication method to convert decimal
fraction to hexadecimal fraction.
For example: if idleslope is 10000 and sendslope is -90000, then
bandwidth is 10000 - (-90000) = 100000.
The 10% bandwidth of 100Mbps means 10/100 = 0.1(decimal). This value has
to be converted to hexa.
1) 0.1 * 16 = 1.6 --> fraction 0.6 Carry = 1 (MSB)
2) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
3) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
4) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
5) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
6) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9 (LSB)
Now 0.1(decimal) becomes 0.199999(Hex).
If it is LAN937x, 24 bit value will be programmed to Credit Inc
register, 0x199999. For others 16 bit value will be prgrammed, 0x1999.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LAN937x family of switches has 8 queues per port where the KSZ switches
has 4 queues per port. By default, only one queue per port is enabled.
The queues are configurable in 2, 4 or 8. This patch add 8 number of
queues for LAN937x and 4 for other switches.
In the tag_ksz.c file, prioirty of the packet is queried using the skb
buffer and the corresponding value is updated in the tag.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Starting with commit eee16b1471 ("net: dsa: microchip: perform the
compatibility check for dev probed"), the KSZ switch driver now bails
out if it thinks the DT compatible doesn't match the actual chip ID
read back from the hardware:
ksz9477-switch 1-005f: Device tree specifies chip KSZ9893 but found
KSZ8563, please fix it!
For the KSZ8563, which used ksz_switch_chips[KSZ9893], this was fine
at first, because it indeed shares the same chip id as the KSZ9893.
Commit b449080956 ("net: dsa: microchip: add separate struct
ksz_chip_data for KSZ8563 chip") started differentiating KSZ9893
compatible chips by consulting the 0x1F register. The resulting breakage
was fixed for the SPI driver in the same commit by introducing the
appropriate ksz_switch_chips[KSZ8563], but not for the I2C driver.
Fix this for I2C-connected KSZ8563 now to get it probing again.
Fixes: b449080956 ("net: dsa: microchip: add separate struct ksz_chip_data for KSZ8563 chip").
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230120110933.1151054-1-a.fatoum@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Felix (VSC9959) has a DEV_GMII:MM_CONFIG block composed of 2 registers
(ENABLE_CONFIG and VERIF_CONFIG). Because the MAC Merge statistics and
pMAC statistics are already in the Ocelot switch lib even if just Felix
supports them, I'm adding support for the whole MAC Merge layer in the
common Ocelot library too.
There is an interrupt (shared with the PTP interrupt) which signals
changes to the MM verification state. This is done because the
preemptible traffic classes should be committed to hardware only once
the verification procedure has declared the link partner of being
capable of receiving preemptible frames.
We implement ethtool getters and setters for the MAC Merge layer state.
The "TX enabled" and "verify status" are taken from the IRQ handler,
using a mutex to ensure serialized access.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix VSC9959 switch supports frame preemption and has a MAC Merge
layer. In addition to the structured stats that exist for the eMAC,
export the counters associated with its pMAC (pause, RMON, MAC, PHY,
control) plus the high-level MAC Merge layer stats. The unstructured
ethtool counters, as well as the rtnl_link_stats64 were left to report
only the eMAC counters.
Because statistics processing is quite self-contained in ocelot_stats.c
now, I've opted for introducing an ocelot->mm_supported bool, based on
which the common switch lib does everything, rather than pushing the
TSN-specific code in felix_vsc9959.c, as happens for other TSN stuff.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO core should not pass a C45 request via the C22 API call any
more. So remove the tests from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While the prior patch moved the adjust_link code into the
phylink_mac_link_up api, this patch cleans it up and adds the setting the
port's flow control based on the phylink_mac_link_up input parameters.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the adjust_link api with the phylink apis that provide
equivalent functionality.
The remaining functionality from the adjust_link is now covered in the
phylink_mac_link_up api.
Removes:
.adjust_link
Adds:
.phylink_get_caps
.phylink_mac_link_up
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparing to move the adjust_link logic into the phylink_mac_link_up
api, change the macro used to check for the cpu port. In
phylink_mac_link_up, the phydev pointer passed in for the CPU port is
NULL, so we can't keep using phy_is_pseudo_fixed_link(phydev).
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the regmap_write() is over a slow bus that will sleep, we can speed up
the boot-up time a bit by not bothering to clear a bit that is already
clear.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While it is highly unlikely a read will ever fail, This code fragment is
now in a function that allows us to return an error code. A read failure
here will cause the lan9303_probe to fail.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparing to remove the .adjust_link api, I am moving the one-time
initialization of the device's Turbo Mode bit into a different execution
path. This code clears (disables) the Turbo Mode bit which is never used
by this driver. Turbo Mode is a non-standard mode that would allow the
100Mbps RMII interface to run at 200Mbps.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whitespace preparatory patch, making the dsa_switch_ops table consistent.
No code is added or removed.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to return negative error codes here but the copy_to/from_user()
functions return the number of bytes remaining to be copied.
Fixes: c59e12a140 ("net: dsa: microchip: ptp: Initial hardware time stamping support")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/Y8fJxSvbl7UNVHh/@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ALU table entry 2 register in KSZ9477 have bit positions reserved for
forwarding port map. This field is referred in ksz9477_fdb_del() for
clearing forward port map and alu table.
But current fdb_del refer ALU table entry 3 register for accessing forward
port map. Update ksz9477_fdb_del() to get forward port map from correct
alu table entry register.
With this bug, issue can be observed while deleting static MAC entries.
Delete any specific MAC entry using "bridge fdb del" command. This should
clear all the specified MAC entries. But it is observed that entries with
self static alone are retained.
Tested on LAN9370 EVB since ksz9477_fdb_del() is used common across
LAN937x and KSZ series.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230118174735.702377-1-rakesh.sankaranarayanan@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The T1 MDIO bus driver can perform both C22 and C45 transfers. Create
separate functions for each and register the C45 versions using the
new API calls where appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sja1105 MDIO bus driver only supports C45 transfers. Update the
function names to make this clear, pass the mmd as a parameter, and
register the accessors to the _c45 ops of the bus driver structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mt7530 does support C45, but its uses a mix of registering its MDIO
bus and providing its private MDIO bus to the DSA core, too. This makes
the change a bit more complex.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch receives management traffic such as STP and LLDP. However, PTP
messages are not received, only transmitted.
Ideally, the switch would trap all PTP messages to the management CPU. This
particular switch has a PTP block which identifies PTP messages and traps them
to a dedicated port. There is a register to program this destination. This is
not used at the moment.
Therefore, program it to the same port as the MGMT traffic is trapped to. This
allows to receive PTP messages as soon as timestamping is enabled.
In addition, the datasheet mentions that this register is not valid e.g., for
6190 variants. So, add a new PTP operation which is added for the 6390 and 6290
devices.
Tested simply like this on Marvell 88E6390, revision 1:
|/ # ptp4l -2 -i lan4 --tx_timestamp_timeout=40 -m
|[...]
|ptp4l[147.450]: master offset 56 s2 freq +1262 path delay 413
|ptp4l[148.450]: master offset 22 s2 freq +1244 path delay 434
|ptp4l[149.450]: master offset 5 s2 freq +1234 path delay 446
|ptp4l[150.451]: master offset 3 s2 freq +1233 path delay 451
|ptp4l[151.451]: master offset 1 s2 freq +1232 path delay 451
|ptp4l[152.451]: master offset -3 s2 freq +1229 path delay 451
|ptp4l[153.451]: master offset 9 s2 freq +1240 path delay 451
Link: https://lore.kernel.org/r/CAFSKS=PJBpvtRJxrR4sG1hyxpnUnQpiHg4SrUNzAhkWnyt9ivg@mail.gmail.com
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enetc MDIO bus driver can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new API calls where appropriate.
This driver is shared with the Felix DSA switch, so update that at the
same time.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is difference in implementation of per_out pins between KSZ9563
and LAN937x. In KSZ9563, Timestamping control register (0x052C) bit 6,
if 1 - timestamp input and 0 - trigger output. But it is opposite for
LAN937x 1 - trigger output and 0 - timestamp input.
As per per_out gpio pins, KSZ9563 has four Led pins and two dedicated
gpio pins. But in LAN937x dedicated gpio pins are removed instead there
are up to 10 LED pins out of which LED_0 and LED_1 can be mapped to PTP
tou 0, 1 or 2. This patch sets the bit 6 in 0x052C register and
configure the LED override and source register for LAN937x series of
switches alone.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN937x series of switches support 2 step timestamping mechanism. There
are timestamp correction calculation performed in ksz_rcv_timestamp and
ksz_xmit_timestamp which are applicable only for p2p1step. To check
whether the 2 step is enabled or not in tag_ksz.c introduced the helper
function in taggger_data to query it from ksz_ptp.c. Based on whether 2
step is enabled or not, timestamp calculation are performed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two programmable pins available for Trigger output unit to
generate periodic pulses. This patch add verify_pin for the available 2
pins and configure it with respect to GPIO index for the TOU unit.
Tested using testptp
./testptp -i 0 -L 0,2
./testptp -i 0 -d /dev/ptp0 -p 1000000000
./testptp -i 1 -L 1,2
./testptp -i 1 -d /dev/ptp0 -p 100000000
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN937x and KSZ PTP supported switches has Three Trigger output unit.
This TOU can used to generate the periodic signal for PTP. TOU has the
cycle width register of 32 bit in size and period width register of 24
bit, each value is of 8ns so the pulse width can be maximum 125ms.
Tested using ./testptp -d /dev/ptp0 -p 1000000000 -w 100000000 for
generating the 10ms pulse width
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For PDelay_Resp messages we will likely have a negative value in the
correction field. The switch hardware cannot correctly update such
values (produces an off by one error in the UDP checksum), so it must be
moved to the time stamp field in the tail tag. Format of the correction
field is 48 bit ns + 16 bit fractional ns. After updating the
correction field, clone is no longer required hence it is freed.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the routines for transmission of ptp packets. When the
ptp pdelay_req packet to be transmitted, it uses the deferred xmit
worker to schedule the packets.
During irq_setup, interrupt for Sync, Pdelay_req and Pdelay_rsp are
enabled. So interrupt is triggered for all three packets. But for
p2p1step, we require only time stamp of Pdelay_req packet. Hence to
avoid posting of the completion from ISR routine for Sync and
Pdelay_resp packets, ts_en flag is introduced. This controls which
packets need to processed for timestamp.
After the packet is transmitted, ISR is triggered. The time at which
packet transmitted is recorded to separate register.
This value is reconstructed to absolute time and posted to the user
application through socket error queue.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx Timestamping is done through 4 additional bytes in tail tag.
Whenever the ptp packet is received, the 4 byte hardware time stamped
value is added before 1 byte tail tag. Also, bit 7 in tail tag indicates
it as PTP frame. This 4 byte value is extracted from the tail tag and
reconstructed to absolute time and assigned to skb hwtstamp.
If the packet received in PDelay_Resp, then partial ingress timestamp
is subtracted from the correction field. Since user space tools expects
to be done in hardware.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP Interrupt mask and status register differ from the global and port
interrupt mechanism by two methods. One is that for global/port
interrupt enabling we have to clear the bit but for ptp interrupt we
have to set the bit. And other is bit12:0 is reserved in ptp interrupt
registers. This forced to not use the generic implementation of
global/port interrupt method routine. This patch implement the ptp
interrupt mechanism to read the timestamp register for sync, pdelay_req
and pdelay_resp.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is used for reconstructing the absolute time from the 32bit
hardware time stamping value. The do_aux ioctl is used for reading the
ptp hardware clock and store it to global variable.
The timestamped value in tail tag during rx and register during tx are
32 bit value (2 bit seconds and 30 bit nanoseconds). The time taken to
read entire ptp clock will be time consuming. In order to speed up, the
software clock is maintained. This clock time will be added to 32 bit
timestamp to get the absolute time stamp.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PTP is enabled in hardware bit 6 of PTP_MSG_CONF1 register, the
transmit frame needs additional 4 bytes before the tail tag. It is
needed for all the transmission packets irrespective of PTP packets or
not.
The 4-byte timestamp field is 0 for frames other than Pdelay_Resp. For
the one-step Pdelay_Resp, the switch needs the receive timestamp of the
Pdelay_Req message so that it can put the turnaround time in the
correction field.
Since PTP has to be enabled for both Transmission and reception
timestamping, driver needs to track of the tx and rx setting of the all
the user ports in the switch.
Two flags hw_tx_en and hw_rx_en are added in ksz_port to track the
timestampping setting of each port. When any one of ports has tx or rx
timestampping enabled, bit 6 of PTP_MSG_CONF1 is set and it is indicated
to tag_ksz.c through tagger bytes. This flag adds 4 additional bytes to
the tail tag. When tx and rx timestamping of all the ports are disabled,
then 4 bytes are not added.
Tested using hwstamp -i <interface>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> # mostly api
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the routine for get_ts_info, hwstamp_get, set. This enables
the PTP support towards userspace applications such as linuxptp.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implement routines (adjfine, adjtime, gettime and settime)
for manipulating the chip's PTP clock. It registers the ptp caps
to posix clock register.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> # mostly api
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The global2 SMI MDIO bus driver can perform both C22 and C45
transfers. Create separate functions for each and register the C45
versions using the new API calls where appropriate. Update the SERDES
code to make use of these new accessors.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This implementation for the Marvell mv88e6xxx chip series is based on
handling ATU miss violations occurring when packets ingress on a port
that is locked with learning on. This will trigger a
SWITCHDEV_FDB_ADD_TO_BRIDGE event, which will result in the bridge module
adding a locked FDB entry. This bridge FDB entry will not age out as
it has the extern_learn flag set.
Userspace daemons can listen to these events and either accept or deny
access for the host, by either replacing the locked FDB entry with a
simple entry or leave the locked entry.
If the host MAC address is already present on another port, a ATU
member violation will occur, but to no real effect, and the packet will
be dropped in hardware. Statistics on these violations can be shown with
the command and example output of interest:
ethtool -S ethX
NIC statistics:
...
atu_member_violation: 5
atu_miss_violation: 23
...
Where ethX is the interface of the MAB enabled port.
Furthermore, as added vlan interfaces where the vid is not added to the
VTU will cause ATU miss violations reporting the FID as
MV88E6XXX_FID_STANDALONE, we need to check and skip the miss violations
handling in this case.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As only the hardware access functions up til and including
mv88e6xxx_g1_atu_mac_read() called under the interrupt handler
need to take the chip lock, we release the chip lock after this call.
The follow up code that handles the violations can run without the
chip lock held.
In further patches, the violation handler function will even be
incompatible with having the chip lock held. This due to an AB/BA
ordering inversion with rtnl_lock().
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The default return value -EOPNOTSUPP of mv88e6xxx_port_bridge_flags()
came from the return value of the DSA method port_egress_floods() in
commit 4f85901f00 ("net: dsa: mv88e6xxx: add support for bridge flags"),
but the DSA API was changed in commit a8b659e7ff ("net: dsa: act as
passthrough for bridge port flags"), resulting in the return value
-EOPNOTSUPP not being valid anymore, and sections for new flags will not
need to set the return value to zero on success, as with the new mab flag
added in a following patch.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Improve mdio master read/write by using singe mii read/write lo/hi.
In a read and write we need to poll the mdio master regs in a busy loop
to check for a specific bit present in the upper half of the reg. We can
ignore the other half since it won't contain useful data. This will save
an additional useless read for each read and write operation.
In a read operation the returned data is present in the mdio master reg
lower half. We can ignore the other half since it won't contain useful
data. This will save an additional useless read for each read operation.
In a read operation it's needed to just set the hi half of the mdio
master reg as the lo half will be replaced by the result. This will save
an additional useless write for each read operation.
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may be useful to read/write just the lo or hi half of a reg.
This is especially useful for phy poll with the use of mdio master.
The mdio master reg is composed by the first 16 bit related to setup and
the other half with the returned data or data to write.
Refactor the mii function to permit single mii read/write of lo or hi
half of the reg.
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2481d206fa.
The Documentation is very confusing about the topic.
The cache logic for hi and lo is wrong and actually miss some regs to be
actually written.
What the Documentation actually intended was that it's possible to skip
writing hi OR lo if half of the reg is not needed to be written or read.
Revert the change in favor of a better and correct implementation.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
The assumption that Documentation was right about how this value work was
wrong. It was discovered that the length value of the mgmt header is in
step of word size.
As an example to process 4 byte of data the correct length to set is 2.
To process 8 byte 4, 12 byte 6, 16 byte 8...
Odd values will always return the next size on the ack packet.
(length of 3 (6 byte) will always return 8 bytes of data)
This means that a value of 15 (0xf) actually means reading/writing 32 bytes
of data instead of 16 bytes. This behaviour is totally absent and not
documented in the switch Documentation.
In fact from Documentation the max value that mgmt eth can process is
16 byte of data while in reality it can process 32 bytes at once.
To handle this we always round up the length after deviding it for word
size. We check if the result is odd and we round another time to align
to what the switch will provide in the ack packet.
The workaround for the length limit of 15 is still needed as the length
reg max value is 0xf(15)
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Fixes: 90386223f4 ("net: dsa: qca8k: add support for larger read/write size with mgmt Ethernet")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP hardware timestamping related objects are not linked when PTP
support for MV88E6xxx (NET_DSA_MV88E6XXX_PTP) is disabled, therefore
NET_DSA_MV88E6XXX should not depend on PTP_1588_CLOCK_OPTIONAL
regardless of NET_DSA_MV88E6XXX_PTP.
Instead, condition more strictly on how NET_DSA_MV88E6XXX_PTP's
dependencies are met, making sure that it cannot be enabled when
NET_DSA_MV88E6XXX=y and PTP_1588_CLOCK=m.
In other words, this commit allows NET_DSA_MV88E6XXX to be built-in
while PTP_1588_CLOCK is a module, as long as NET_DSA_MV88E6XXX_PTP is
prevented from being enabled.
Fixes: e5f3155267 ("ethernet: fix PTP_1588_CLOCK dependencies")
Signed-off-by: Johnny S. Lee <foss@jsl.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ swithes used interrupts for detecting the phy link up and down.
During registering the interrupt handler, it used IRQF_TRIGGER_FALLING
flag. But this flag has to be retrieved from device tree instead of hard
coding in the driver, so removing the flag.
Fixes: ff319a6448 ("net: dsa: microchip: move interrupt handling logic from lan937x to ksz_common")
Reported-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20221213101440.24667-1-arun.ramadoss@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King correctly pointed out that the MAC_2500FD capability is
already added for port 5 (if not in RGMII mode) and port 6 (which only
supports SGMII) by mt7531_mac_port_get_caps. Remove the reduntant
setting of this capability flag which was added by a previous commit.
Fixes: e19de30d20 ("net: dsa: mt7530: add support for in-band link status")
Reported-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/Y5qY7x6la5TxZxzX@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the blamed commit, it was not noticed that one implementation of
chip->info->ops->phylink_get_caps(), called by mv88e6xxx_get_caps(),
may access hardware registers, and in doing so, it takes the
mv88e6xxx_reg_lock(). Namely, this is mv88e6352_phylink_get_caps().
This is a problem because mv88e6xxx_get_caps(), apart from being
a top-level function (method invoked by dsa_switch_ops), is now also
directly called from mv88e6xxx_setup_port(), which runs under the
mv88e6xxx_reg_lock() taken by mv88e6xxx_setup(). Therefore, when running
on mv88e6352, the reg_lock would be acquired a second time and the
system would deadlock on driver probe.
The things that mv88e6xxx_setup() can compete with in terms of register
access with are the IRQ handlers and MDIO bus operations registered by
mv88e6xxx_probe(). So there is a real need to acquire the register lock.
The register lock can, in principle, be dropped and re-acquired pretty
much at will within the driver, as long as no operations that involve
waiting for indirect access to complete (essentially, callers of
mv88e6xxx_smi_direct_wait() and mv88e6xxx_wait_mask()) are interrupted
with the lock released. However, I would guess that in mv88e6xxx_setup(),
the critical section is kept open for such a long time just in order to
optimize away multiple lock/unlock operations on the registers.
We could, in principle, drop the reg_lock right before the
mv88e6xxx_setup_port() -> mv88e6xxx_get_caps() call, and
re-acquire it immediately afterwards. But this would look ugly, because
mv88e6xxx_setup_port() would release a lock which it didn't acquire, but
the caller did.
A cleaner solution to this issue comes from the observation that struct
mv88e6xxxx_ops methods generally assume they are called with the
reg_lock already acquired. Whereas mv88e6352_phylink_get_caps() is more
the exception rather than the norm, in that it acquires the lock itself.
Let's enforce the same locking pattern/convention for
chip->info->ops->phylink_get_caps() as well, and make
mv88e6xxx_get_caps(), the top-level function, acquire the register lock
explicitly, for this one implementation that will access registers for
port 4 to work properly.
This means that mv88e6xxx_setup_port() will no longer call the top-level
function, but the low-level mv88e6xxx_ops method which expects the
correct calling context (register lock held).
Compared to chip->info->ops->phylink_get_caps(), mv88e6xxx_get_caps()
also fixes up the supported_interfaces bitmap for internal ports, since
that can be done generically and does not require per-switch knowledge.
That's code which will no longer execute, however mv88e6xxx_setup_port()
doesn't need that. It just needs to look at the mac_capabilities bitmap.
Fixes: cc1049ccee ("net: dsa: mv88e6xxx: fix speed setting for CPU/DSA ports")
Reported-by: Maksim Kiselev <bigunclemax@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20221214110120.3368472-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Merge in the left-over fixes before the net-next pull-request.
net/mptcp/subflow.c
d3295fee3c ("mptcp: use proper req destructor for IPv6")
36b122baf6 ("mptcp: add subflow_v(4,6)_send_synack()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It is possible to trigger these VTU violation messages very easily,
it's only necessary to send packets with an unknown VLAN ID to a port
that belongs to a VLAN-aware bridge.
Do a similar thing as for ATU violation messages, and hide them in the
kernel's trace buffer.
New usage model:
$ trace-cmd list | grep mv88e6xxx
mv88e6xxx
mv88e6xxx:mv88e6xxx_vtu_miss_violation
mv88e6xxx:mv88e6xxx_vtu_member_violation
$ trace-cmd report
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In applications where the switch ports must perform 802.1X based
authentication and are therefore locked, ATU violation interrupts are
quite to be expected as part of normal operation. The problem is that
they currently spam the kernel log, even if rate limited.
Create a series of trace points, all derived from the same event class,
which log these violations to the kernel's trace buffer, which is both
much faster and much easier to ignore than printing to a serial console.
New usage model:
$ trace-cmd list | grep mv88e6xxx
mv88e6xxx
mv88e6xxx:mv88e6xxx_atu_full_violation
mv88e6xxx:mv88e6xxx_atu_miss_violation
mv88e6xxx:mv88e6xxx_atu_member_violation
$ trace-cmd record -e mv88e6xxx sleep 10
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When an ATU violation occurs, the switch uses the ATU FID register to
report the FID of the MAC address that incurred the violation. It would
be good for the driver to know the FID value for purposes such as
logging and CPU-based authentication.
Up until now, the driver has been calling the mv88e6xxx_g1_atu_op()
function to read ATU violations, but that doesn't do exactly what we
want, namely it calls mv88e6xxx_g1_atu_fid_write() with FID 0.
(side note, the documentation for the ATU Get/Clear Violation command
says that writes to the ATU FID register have no effect before the
operation starts, it's only that we disregard the value that this
register provides once the operation completes)
So mv88e6xxx_g1_atu_fid_write() is not what we want, but rather
mv88e6xxx_g1_atu_fid_read(). However, the latter doesn't exist, we need
to write it.
The remainder of mv88e6xxx_g1_atu_op() except for
mv88e6xxx_g1_atu_fid_write() is still needed, namely to send a
GET_CLR_VIOLATION command to the ATU. In principle we could have still
kept calling mv88e6xxx_g1_atu_op(), but the MDIO writes to the ATU FID
register are pointless, but in the interest of doing less CPU work per
interrupt, write a new function called mv88e6xxx_g1_read_atu_violation()
and call it.
The FID will be the port default FID as set by mv88e6xxx_port_set_fid()
if the VID from the packet cannot be found in the VTU. Otherwise it is
the FID derived from the VTU entry associated with that VID.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the MV88E6XXX_PORT_ASSOC_VECTOR_INT_AGE_OUT bit (interrupt on
age out) is not enabled by the driver, and as a result, the print for
age out violations is dead code.
Remove it until there is some way for this to be triggered.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch fixes an issue where a read failure of a port statistic counter
will return unknown results. While it is highly unlikely the read will
ever fail, it is much cleaner to return a zero for the stat count.
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221209153502.7429-1-jerry.ray@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SJA1105 family has 45 L2 policing table entries
(SJA1105_MAX_L2_POLICING_COUNT) and SJA1110 has 110
(SJA1110_MAX_L2_POLICING_COUNT). Keeping the table structure but
accounting for the difference in port count (5 in SJA1105 vs 10 in
SJA1110) does not fully explain the difference. Rather, the SJA1110 also
has L2 ingress policers for multicast traffic. If a packet is classified
as multicast, it will be processed by the policer index 99 + SRCPORT.
The sja1105_init_l2_policing() function initializes all L2 policers such
that they don't interfere with normal packet reception by default. To have
a common code between SJA1105 and SJA1110, the index of the multicast
policer for the port is calculated because it's an index that is out of
bounds for SJA1105 but in bounds for SJA1110, and a bounds check is
performed.
The code fails to do the proper thing when determining what to do with the
multicast policer of port 0 on SJA1105 (ds->num_ports = 5). The "mcast"
index will be equal to 45, which is also equal to
table->ops->max_entry_count (SJA1105_MAX_L2_POLICING_COUNT). So it passes
through the check. But at the same time, SJA1105 doesn't have multicast
policers. So the code programs the SHARINDX field of an out-of-bounds
element in the L2 Policing table of the static config.
The comparison between index 45 and 45 entries should have determined the
code to not access this policer index on SJA1105, since its memory wasn't
even allocated.
With enough bad luck, the out-of-bounds write could even overwrite other
valid kernel data, but in this case, the issue was detected using KASAN.
Kernel log:
sja1105 spi5.0: Probed switch chip: SJA1105Q
==================================================================
BUG: KASAN: slab-out-of-bounds in sja1105_setup+0x1cbc/0x2340
Write of size 8 at addr ffffff880bd57708 by task kworker/u8:0/8
...
Workqueue: events_unbound deferred_probe_work_func
Call trace:
...
sja1105_setup+0x1cbc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Allocated by task 8:
...
sja1105_setup+0x1bcc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Fixes: 38fbe91f22 ("net: dsa: sja1105: configure the multicast policers, if present")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Radu Nicolae Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20221207132347.38698-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ethernet-controller dt-schema, mostly pushed forward by Linux, has
the "internal" PHY mode for denoting MAC connections to an internal PHY.
U-Boot may provide device tree blobs where this phy-mode is specified,
so make the Linux driver accept them.
It appears that the current behavior with phy-mode = "internal" was
introduced when mv88e6xxx started reporting supported_interfaces to
phylink. Prior to that, I don't think it would have any issues accepting
this phy-mode.
Fixes: d4ebf12bce ("net: dsa: mv88e6xxx: populate supported_interfaces and mac_capabilities")
Link: https://lore.kernel.org/linux-arm-kernel/20221205172709.kglithpbhdbsakvd@skbuf/T/
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Tim Harvey <tharvey@gateworks.com> # imx6q-gw904.dts
Link: https://lore.kernel.org/r/20221205194845.2131161-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
To make the code more comparable to KSZ9477 code, move DSA
configurations to the same location.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
KSZ8795 and KSZ9477 compatible series of switches use global max frame
size configuration register. So, enable MTU normalization for this reason.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make MTU configurable on KSZ87xx and KSZ88xx series of switches.
Before this patch, pre-configured behavior was different on different
switch series, due to opposite meaning of the same bit:
- KSZ87xx: Reg 4, Bit 1 - if 1, max frame size is 1532; if 0 - 1514
- KSZ88xx: Reg 4, Bit 1 - if 1, max frame size is 1514; if 0 - 1532
Since the code was telling "... SW_LEGAL_PACKET_DISABLE, true)", I
assume, the idea was to set max frame size to 1532.
With this patch, by setting MTU size 1500, both switch series will be
configured to the 1532 frame limit.
This patch was tested on KSZ8873.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add ksz_rmw8(), it will be used in the next patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If we have global MTU configuration, it is enough to configure it on CPU
port only.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are no HW specific registers, so we can process all of them
in one location.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Arun Ramadoss <arun.ramadoss@microchip.com> (KSZ9893 and LAN937x)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver name is available in device_driver::name. Right now,
drivers still have to report this piece of information themselves in
their devlink_ops::info_get callback function.
In order to factorize code, make devlink_nl_info_fill() add the driver
name attribute.
Now that the core sets the driver name attribute, drivers are not
supposed to call devlink_info_driver_name_put() anymore. Remove
devlink_info_driver_name_put() and clean-up all the drivers using this
function in their callback.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Tested-by: Ido Schimmel <idosch@nvidia.com> # mlxsw
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch changes the reported ethtool statistics for the lan9303
family of parts covered by this driver.
The TxUnderRun statistic label is renamed to RxShort to accurately
reflect what stat the device is reporting. I did not reorder the
statistics as that might cause problems with existing user code that
are expecting the stats at a certain offset.
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221128193559.6572-1-jerry.ray@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no reason that I can see why the no-op tagging protocol should
be registered manually, so make it a module and make all drivers which
have any sort of reference to DSA_TAG_PROTO_NONE select it.
Note that I don't know if ksz_get_tag_protocol() really needs this,
or if it's just the logic which is poorly written. All switches seem to
have their own tagging protocol, and DSA_TAG_PROTO_NONE is just a
fallback that never gets used.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ever since commit 4d1d157fb6 ("net: mscc: ocelot: share the common stat
definitions between all drivers") the stats_layout entry in ocelot and
felix drivers have become redundant. Remove the unnecessary code.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
You'd think people know that the internal 100BASE-TX PHY on the SJA1110
responds only to clause 22 MDIO transactions, but they don't :)
When a clause 45 transaction is attempted, sja1105_base_tx_mdio_read()
and sja1105_base_tx_mdio_write() don't expect "reg" to contain bit 30
set (MII_ADDR_C45) and pack this value into the SPI transaction buffer.
But the field in the SPI buffer has a width smaller than 30 bits, so we
see this confusing message from the packing() API rather than a proper
rejection of C45 transactions:
Call trace:
dump_stack+0x1c/0x38
sja1105_pack+0xbc/0xc0 [sja1105]
sja1105_xfer+0x114/0x2b0 [sja1105]
sja1105_xfer_u32+0x44/0xf4 [sja1105]
sja1105_base_tx_mdio_read+0x44/0x7c [sja1105]
mdiobus_read+0x44/0x80
get_phy_c45_ids+0x70/0x234
get_phy_device+0x68/0x15c
fwnode_mdiobus_register_phy+0x74/0x240
of_mdiobus_register+0x13c/0x380
sja1105_mdiobus_register+0x368/0x490 [sja1105]
sja1105_setup+0x94/0x119c [sja1105]
Cannot store 401d2405 inside bits 24-4 (would truncate)
Fixes: 5a8f09748e ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the custom implementation of phylink_validate() in favor of the
generic one, which requires config->mac_capabilities to be set.
This was used up until now because of the possibility of being paired
with Aquantia PHYs with support for rate matching. The phylink framework
gained generic support for these, and knows to advertise all 10/100/1000
lower speed link modes when our SERDES protocol is 2500base-x
(fixed speed).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Probe functions uses normal dev_err() to check error conditions
and print messages. Replace dev_err() with dev_err_probe() to
have more standardized format and error logging.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ8563 have three port interrupts: PTP, PHY and ACL. Add
port_nirq as 3 for KSZ8563 inside ksz_chip_data.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add status validation for port register write inside
lan937x_change_mtu. ksz_pwrite and ksz_pread api's are
updated with return type int (Reference patch mentioned
below). Update lan937x_change_mtu with status validation
for ksz_pwrite16().
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20220826105634.3855578-6-o.rempel@pengutronix.de/
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add device irq in i2c probe function.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
