-----BEGIN PGP SIGNATURE-----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=pOqY
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Resource management:
- Distribute spare resources to unconfigured hotplug bridges at
boot-time (not just when hot-adding such a bridge), which makes
hot-adding devices to docks work better.
- Revert to a BAR assignment inherited from firmware only when the
address is actually reachable via any upstream bridges, which fixes
some cases where firmware doesn't configure all devices.
- Add a sysfs interface to resize BARs so this can be done before
assigning devices to a VM through VFIO.
Power management:
- Disable Precision Time Management for all devices on suspend to
enable lower-power PM state. We previously did this just for Root
Ports, which isn't enough because downstream devices can still
generate PTM messages, which cause errors if it's disabled in the
Root Port.
- Save and restore the ASPM L1 PM Substates configuration for
suspend/ resume. Previously this configuration was lost, so L1.x
states likely stopped working after resume.
- Check whether the L1 PM Substates Capability exists. If it didn't
exist, we previously read junk and tried to configure L1 Substates
based on that.
- Fix the LTR_L1.2_THRESHOLD computation, which previously set a
threshold for entering L1.2 that was too low in some cases.
- Reduce the delay after transitions to or from D3cold by using
usleep_range() rather than msleep(), which often slept for ~19ms
instead of the 10ms normally required. The spec says 10ms is
enough, but it's possible we could trip over devices that need a
little more.
Error handling:
- Work around a BIOS bug that caused Intel Root Ports to advertise a
Root Port Programmed I/O (RP PIO) log size of zero, which caused
annoying warnings and prevented the kernel from dumping log
registers for DPC errors.
Qualcomm PCIe controller driver:
- Add support for SC8280XP and SA8540P host controllers and SM8450
endpoint controller.
- Disable Master AXI clock on endpoint controllers to save power when
link is idle or in L1.x.
- Expose link state transition counts via debugfs to help debug
issues with low-power states.
- Add auto-loading module support.
Synopsys DesignWare PCIe controller driver:
- Remove a dependency on ZONE_DMA32 by allocating the MSI target page
differently. There's more work to do related to eDMA controllers,
so it's not completely settled"
* tag 'pci-v6.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (71 commits)
PCI: qcom-ep: Check platform_get_resource_byname() return value
PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Define clocks per platform
PCI: qcom-ep: Make PERST separation optional
dt-bindings: PCI: qcom-ep: Make PERST separation optional
PCI: qcom-ep: Disable Master AXI Clock when there is no PCIe traffic
PCI: Expose PCIe Resizable BAR support via sysfs
PCI/ASPM: Correct LTR_L1.2_THRESHOLD computation
PCI/ASPM: Ignore L1 PM Substates if device lacks capability
PCI/ASPM: Factor out L1 PM Substates configuration
PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS
PCI: qcom-ep: Expose link transition counts via debugfs
PCI: qcom-ep: Disable IRQs during driver remove
PCI/ASPM: Save L1 PM Substates Capability for suspend/resume
PCI/ASPM: Refactor L1 PM Substates Control Register programming
PCI: qcom-ep: Make use of the cached dev pointer
PCI: qcom-ep: Rely on the clocks supplied by devicetree
PCI: qcom-ep: Add kernel-doc for qcom_pcie_ep structure
phy: freescale: imx8m-pcie: Fix the wrong order of phy_init() and phy_power_on()
...
- Add macros for PCI Configuration Mechanism #1 and use them in the
ftpci100, mt7621, and tegra drivers (Pali Rohár)
* remotes/lorenzo/pci/misc:
PCI: tegra: Use PCI_CONF1_EXT_ADDRESS() macro
PCI: mt7621: Use PCI_CONF1_EXT_ADDRESS() macro
PCI: ftpci100: Use PCI_CONF1_ADDRESS() macro
PCI: Add standard PCI Config Address macros
- List platforms that use a single MSI host interrupt in qcom DT (Johan
Hovold)
- Add SC8280XP, SA8540P support to qcom DT binding and driver(Johan Hovold)
- Make all optional clocks truly optional in the driver (Johan Hovold)
- Rename per-IP structs to reflect the IP version (Johan Hovold)
- Sort device ID match table by compatible string (Johan Hovold)
- Add MODULE_DEVICE_TABLE to enable module autoloading (Dmitry Baryshkov)
- Drop the unused .post_deinit() callback (Johan Hovold)
- Rely on DT for clock information instead of hard-coding it in the driver
(Manivannan Sadhasivam)
- Disable IRQs when removing driver to avoid spurious IRQs later
(Manivannan Sadhasivam)
- Expose link transition counts via debugfs to help debug issues with
low-power states (Manivannan Sadhasivam)
- Gate Master AXI clock to the MHI bus while in L1 substates to save power
(Manivannan Sadhasivam)
- Disable Master AXI clock to save power when there is no traffic on PCIe
(Manivannan Sadhasivam)
- Make the "PERST separation" debug feature optional in the DT and the
driver (Manivannan Sadhasivam)
- Define clocks to be per-platform in DT to prepare for future SoCs
(Manivannan Sadhasivam)
- Add SM8450 SoC support (Manivannan Sadhasivam)
- Check for platform_get_resource_byname() to avoid a NULL pointer
dereference (Yang Yingliang)
* pci/qcom:
PCI: qcom-ep: Check platform_get_resource_byname() return value
PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Define clocks per platform
PCI: qcom-ep: Make PERST separation optional
dt-bindings: PCI: qcom-ep: Make PERST separation optional
PCI: qcom-ep: Disable Master AXI Clock when there is no PCIe traffic
PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS
PCI: qcom-ep: Expose link transition counts via debugfs
PCI: qcom-ep: Disable IRQs during driver remove
PCI: qcom-ep: Make use of the cached dev pointer
PCI: qcom-ep: Rely on the clocks supplied by devicetree
PCI: qcom-ep: Add kernel-doc for qcom_pcie_ep structure
PCI: qcom: Rename host-init error label
PCI: qcom: Drop unused post_deinit callback
PCI: qcom-ep: Add MODULE_DEVICE_TABLE
PCI: qcom: Sort device-id table
PCI: qcom: Clean up IP configurations
PCI: qcom: Make all optional clocks optional
PCI: qcom: Add support for SA8540P
PCI: qcom: Add support for SC8280XP
dt-bindings: PCI: qcom: Add SA8540P to binding
dt-bindings: PCI: qcom: Add SC8280XP to binding
dt-bindings: PCI: qcom: Enumerate platforms with single msi interrupt
- Rename the pcie-mediatek-gen3 driver from 'mtk-pcie' to 'mtk-pcie-gen3'
so it can coexist with the pcie-mediatek driver, which also uses
'mtk-pcie' (Felix Fietkau)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek-gen3: Change driver name to mtk-pcie-gen3
- Use dmam_alloc_coherent() instead of dma_map_page() to allocate the MSI
target page, which means dwc drivers will work even when ZONE_DMA32 is
disabled (Will McVicker)
- If we can't allocate an MSI target page with a 32-bit address, try
allocating one with a 64-bit address (Will McVicker)
- Switch from of_gpio_named_count() to generic gpiod_count() (Andy
Shevchenko)
- Add support for i.MX8MP PCIe (Richard Zhu)
- Fix the Freescale i.MX8 PHY driver, which had interchanged the phy_init()
and phy_power_on() interfaces (Richard Zhu)
* remotes/lorenzo/pci/dwc:
phy: freescale: imx8m-pcie: Fix the wrong order of phy_init() and phy_power_on()
PCI: imx6: Add i.MX8MP PCIe support
PCI: dwc: Replace of_gpio_named_count() by gpiod_count()
PCI: dwc: Drop dependency on ZONE_DMA32
- In an emulated PCI bridge, set Capability offsets so they match the
hardware offsets shown by U-Boot (Pali Rohár)
* remotes/lorenzo/pci/bridge-emul:
PCI: pci-bridge-emul: Set position of PCI capabilities to real HW value
- Switch from gpiod_get_from_of_node() to generic devm GPIO API (Dmitry
Torokhov)
* remotes/lorenzo/pci/apple:
PCI: apple: Do not leak reset GPIO on unbind/unload/error
If platform_get_resource_byname() fails, 'mmio_res' will be set to NULL
pointer, which causes a NULL pointer dereference when it is used in
qcom_pcie_perst_deassert().
Check the return value to prevent it.
Link: https://lore.kernel.org/r/20220429080740.1294797-1-yangyingliang@huawei.com
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Add support for SM8450 SoC to the Qualcomm PCIe Endpoint Controller
driver. The driver uses the same config as the existing SDX55 chipset,
so additional settings are not required.
Link: https://lore.kernel.org/r/20220914075350.7992-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PERST separation is an optional debug feature used to collect the crash
dump from the PCIe endpoint devices by the PCIe host when the endpoint
crashes. This feature keeps the PCIe link up by separating the PCIe IP
block from the SoC reset logic.
Make the property optional in the driver.
Link: https://lore.kernel.org/r/20220914075350.7992-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Master AXI clock can be disabled when it is not used i.e., when there
is no traffic on the PCIe bus. This helps to save power during idle state.
[bhelgaas: tidy and wrap comment]
Link: https://lore.kernel.org/r/20220914075350.7992-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Qualcomm PCIe controllers have debug registers in the MMIO region
that count PCIe link transitions. Expose them over debugfs to
userspace to help debug the low power issues.
Link: https://lore.kernel.org/r/20220914075350.7992-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Disable the Global and PERST IRQs during driver remove to avoid getting
spurious IRQs after resource deallocation.
Link: https://lore.kernel.org/r/20220914075350.7992-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
In the qcom_pcie_ep_get_resources() function, dev pointer is already
cached in a local variable. So let's make use of it instead of getting
the dev pointer again from pdev struct.
Link: https://lore.kernel.org/r/20220914075350.7992-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Generally, device drivers should just rely on the platform data like
devicetree to supply the clocks required for the functioning of the
peripheral. There is no need to hardcode the clk info in the driver.
So get rid of the static clk info and obtain the platform supplied
clks.
The total number of clocks supplied is obtained using the
devm_clk_bulk_get_all() API and used for the rest of the clk_bulk_ APIs.
Link: https://lore.kernel.org/r/20220914075350.7992-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Refer to phy_core driver, phy_init() must be called before phy_power_on().
Fix the wrong order of phy_init() and phy_power_on() here.
Link: https://lore.kernel.org/r/1662344583-18874-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 1aa97b0022 ("phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Add i.MX8MP PCIe support.
To avoid codes duplication when find the syscon regmap, add the iomux
gpr syscon compatible into drvdata.
Link: https://lore.kernel.org/r/1662109086-15881-8-git-send-email-hongxing.zhu@nxp.com
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
As a preparation to unexport of_gpio_named_count(), convert the
driver to use gpiod_count() instead.
Link: https://lore.kernel.org/r/20220830183310.48541-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Drop the unused and confusingly named post_deinit callback that was
added for the now removed pipe clock handling.
If ever needed we can add back a callback named pre_deinit (or perhaps
rather pre_phy_power_off) instead.
Link: https://lore.kernel.org/r/20220928155421.21660-2-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Simplify pci-ftpci100.c driver code and use new PCI_CONF1_ADDRESS() macro
for accessing PCI config space.
Link: https://lore.kernel.org/r/20220924092404.31776-3-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Register with Subsystem Device/Vendor ID is at offset 0x2c.
Export it via the emulated bridge to enable support for the Subsystem
Device/Vendor ID - by reading it in the PCI controller config space and
storing it in the emulated bridge control structures, so that it is
exposed in the respective PCI capability.
After this change Subsystem ID is visible in lspci output at line:
Capabilities: [40] Subsystem
Link: https://lore.kernel.org/r/20220711225915.13896-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
The driver allocates reset GPIO in apple_pcie_setup_port() but neither
releases the resource, nor uses devm API to have it released
automatically.
Let's fix this by switching to devm API. While at it let's use generic
devm_fwnode_gpiod_get() instead of OF-specific gpiod_get_from_of_node()
- this will allow us top stop exporting the latter down the road.
Link: https://lore.kernel.org/r/YxatO5OaI2RpxQ2M@google.com
Fixes: 1e33888fbe ("PCI: apple: Add initial hardware bring-up")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Hector Martin <marcan@marcan.st>
Acked-by: Marc Zyngier <maz@kernel.org>
Re-work the msi_msg DMA allocation logic to use dmam_alloc_coherent() which
uses the coherent DMA mask to try to return an allocation within the DMA
mask limits. With that, we now can drop the msi_page parameter in struct
dw_pcie_rp. This allows kernel configurations that disable ZONE_DMA32 to
continue supporting a 32-bit DMA mask. Without this patch, the PCIe host
device will fail to probe when ZONE_DMA32 is disabled.
Link: https://lore.kernel.org/r/20220825235404.4132818-2-willmcvicker@google.com
Fixes: 35797e672f ("PCI: dwc: Fix MSI msi_msg DMA mapping")
Reported-by: Isaac J. Manjarres <isaacmanjarres@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
mvebu and aardvark HW have PCIe capabilities on different offset in PCI
config space. Extend pci-bridge-emul.c code to allow setting custom driver
custom value where PCIe capabilities starts.
With this change PCIe capabilities of both drivers are reported at the same
location as where they are reported by U-Boot - in their real HW offset.
Link: https://lore.kernel.org/r/20220824112124.21675-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
driver_register() will refuse to register another driver with the same name.
This change allows pcie-mediatek-gen3 to coexist with pcie-mediatek built into
the kernel.
Link: https://lore.kernel.org/r/20220505083907.86598-1-nbd@nbd.name
Fixes: d3bf75b579 ("PCI: mediatek-gen3: Add MediaTek Gen3 driver for MT8192")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Jianjun Wang <jianjun.wang@mediatek.com>
PCI emul bridge members iolimitupper, iobaseupper, memlimit and membase
are of type __le16, so correctly access these members using
le16_to_cpu() macros.
Link: https://lore.kernel.org/r/20220812141115.24082-1-pali@kernel.org
Fixes: e7a0187672 ("PCI: mvebu: Propagate errors when updating PCI_IO_BASE and PCI_MEM_BASE registers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Sort the device-id table entries alphabetically by compatible string to
make it easier to find entries and add new ones.
Link: https://lore.kernel.org/r/20220714071348.6792-9-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The various IP versions have different configurations that are encoded
in separate sets of operation callbacks. Currently, there is no need for
also maintaining corresponding sets of data parameters, but it is
conceivable that these may again be found useful (e.g. to implement
minor variations of the operation callbacks).
Rename the default configuration structures after the IP version they
apply to so that they can more easily be reused by different SoCs.
Note that SoC specific configurations can be added later if need arises
(e.g. cfg_sc8280xp).
Link: https://lore.kernel.org/r/20220714071348.6792-8-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The kernel is not a devicetree validator and does not need to re-encode
information which is already available in the devicetree.
This is specifically true for the optional PCIe clocks, some of which
are really interconnect clocks.
Treat also the 2.7.0 optional clocks as truly optional instead of
maintaining a list of clocks per compatible (including two compatible
strings for the two identical controllers on sm8450) just to validate
the devicetree.
Link: https://lore.kernel.org/r/20220714071348.6792-7-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The SA8540P platform has five PCIe controllers: two 4-lane, two 2-lane
and one 1-lane.
Add a new "qcom,pcie-sa8540p" compatible string and reuse the 1.9.0 ops.
Note that like for SC8280XP, the SA8540P controllers need two or three
interconnect clocks to be enabled.
Link: https://lore.kernel.org/r/20220714071348.6792-6-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The SC8280XP platform has seven PCIe controllers: two used with USB4,
two 4-lane, two 2-lane and one 1-lane.
Add a new "qcom,pcie-sc8280xp" compatible string and reuse the 1.9.0
ops.
Note that the SC8280XP controllers need two or three interconnect
clocks to be enabled. Model these as optional clocks to avoid encoding
devicetree data in the PCIe driver.
Note that the same could be done for the SM8450 interconnect clocks and
possibly also for the TBU clocks.
Link: https://lore.kernel.org/r/20220714071348.6792-5-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
With Broadcom Broadband arch ARCH_BCMBCA supported in the kernel, this
patch series migrate the ARCH_BCM4908 symbol to ARCH_BCMBCA. Hence
replace ARCH_BCM4908 with ARCH_BCMBCA in subsystem Kconfig files.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> (for watchdog)
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (for drivers/pci)
Acked-by: Wolfram Sang <wsa@kernel.org> (for i2c)
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> (for reset)
Link: https://lore.kernel.org/r/20220803175455.47638-7-william.zhang@broadcom.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
and NTB EndPoint Function (EPF) support and the various fixes from that
being in -next for Linux v5.20
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEoE9b9c3U2JxX98mqbmZLrHqL0iMFAmL2skgACgkQbmZLrHqL
0iMaAhAAlHvhdSvq7huLkbKd22TdorqaU3bVCYB0KzPR7Ghc4P5XqdLE1VI+TAFD
PXFpD6D2VoGxAuh2PKHzRyAGcV4nr8JDBMZtgpJOcJr3rFhdg1wlfIX1jemrCxTT
9clSEyJ4WSbRpSXq5cbbF3AqaMPPlZ2wMiopKPieCxjTyqld1Wf80ah58GyeT9ut
8zyRzsgOI22WjQmIY13pWUWSTZFtomaM/oVaTC1eepES/t+/1L6/AmucVGY43SnD
N8LEZroRRHmFlyI7H9J1U580sTZVqaEBJoKfN66wnTMCXPR/+8zWprZOLB+R5A+L
klJY7PakrKd7mlafUbRxsBcKnSIrB7UtVZR8Xs2SlReSEqmcDEnIXq8Ga6RZOGKf
hsk72KtqtyFHycFqw8kVGc+hLon39RUd7HI8a3jyrOmJKp3bJ/iQxiLEuKpScZKm
sS6bmBMXJCV9o8UJM7GbyX5kRIki+Dc66dFIcqLFwHN0e0I6yV8TE9HZ5SXtsFri
uBwlzRbdYctJm9+1WT2FxuCb1H5DZaMdKCf2fQQnWXW2PqLIlKj2uE1O6IctIBJr
rlZea6ZOU8zUsIMdANlezJuoTol/bNRWqYbRm0x69lYI7+SYDov3Dg5SAhgJtLFn
F/zaGcO2aTKLxBjXyx+Zu2KgEYR8N+cLYKhLY3/Cv6/vt4CbW2Y=
=DAah
-----END PGP SIGNATURE-----
Merge tag 'ntb-5.20' of https://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"Non-Transparent Bridge updates.
Fix of heap data and clang warnings, support for a new Intel NTB
device, and NTB EndPoint Function (EPF) support and the various fixes
for that"
* tag 'ntb-5.20' of https://github.com/jonmason/ntb:
MAINTAINERS: add PCI Endpoint NTB drivers to NTB files
NTB: EPF: Tidy up some bounds checks
NTB: EPF: Fix error code in epf_ntb_bind()
PCI: endpoint: pci-epf-vntb: reduce several globals to statics
PCI: endpoint: pci-epf-vntb: fix error handle in epf_ntb_mw_bar_init()
PCI: endpoint: Fix Kconfig dependency
NTB: EPF: set pointer addr to null using NULL rather than 0
Documentation: PCI: extend subheading underline for "lspci output" section
Documentation: PCI: Use code-block block for scratchpad registers diagram
Documentation: PCI: Add specification for the PCI vNTB function device
PCI: endpoint: Support NTB transfer between RC and EP
NTB: epf: Allow more flexibility in the memory BAR map method
PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address
ntb: intel: add GNR support for Intel PCIe gen5 NTB
NTB: ntb_tool: uninitialized heap data in tool_fn_write()
ntb: idt: fix clang -Wformat warnings
ntb_mw_set_trans() will set memory map window after endpoint function
driver bind. The inbound map address need be updated dynamically when
using NTB by PCIe Root Port and PCIe Endpoint connection.
Checking if iatu already assigned to the BAR, if yes, using assigned iatu
number to update inbound address map and skip set BAR's register.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
-----BEGIN PGP SIGNATURE-----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=9TAR
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Consolidate duplicated 'next function' scanning and extend to allow
'isolated functions' on s390, similar to existing hypervisors
(Niklas Schnelle)
Resource management:
- Implement pci_iobar_pfn() for sparc, which allows us to remove the
sparc-specific pci_mmap_page_range() and pci_mmap_resource_range().
This removes the ability to map the entire PCI I/O space using
/proc/bus/pci, but we believe that's already been broken since
v2.6.28 (Arnd Bergmann)
- Move common PCI definitions to asm-generic/pci.h and rework others
to be be more specific and more encapsulated in arches that need
them (Stafford Horne)
Power management:
- Convert drivers to new *_PM_OPS macros to avoid need for '#ifdef
CONFIG_PM_SLEEP' or '__maybe_unused' (Bjorn Helgaas)
Virtualization:
- Add ACS quirk for Broadcom BCM5750x multifunction NICs that isolate
the functions but don't advertise an ACS capability (Pavan Chebbi)
Error handling:
- Clear PCI Status register during enumeration in case firmware left
errors logged (Kai-Heng Feng)
- When we have native control of AER, enable error reporting for all
devices that support AER. Previously only a few drivers enabled
this (Stefan Roese)
- Keep AER error reporting enabled for switches. Previously we
enabled this during enumeration but immediately disabled it (Stefan
Roese)
- Iterate over error counters instead of error strings to avoid
printing junk in AER sysfs counters (Mohamed Khalfella)
ASPM:
- Remove pcie_aspm_pm_state_change() so ASPM config changes, e.g.,
via sysfs, are not lost across power state changes (Kai-Heng Feng)
Endpoint framework:
- Don't stop an EPC when unbinding an EPF from it (Shunsuke Mie)
Endpoint embedded DMA controller driver:
- Simplify and clean up support for the DesignWare embedded DMA
(eDMA) controller (Frank Li, Serge Semin)
Broadcom STB PCIe controller driver:
- Avoid config space accesses when link is down because we can't
recover from the CPU aborts these cause (Jim Quinlan)
- Look for power regulators described under Root Ports in DT and
enable them before scanning the secondary bus (Jim Quinlan)
- Disable/enable regulators in suspend/resume (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Simplify and clean up clock and PHY management (Richard Zhu)
- Disable/enable regulators in suspend/resume (Richard Zhu)
- Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu)
- Allow speeds faster than Gen2 (Richard Zhu)
- Make link being down a non-fatal error so controller probe doesn't
fail if there are no Endpoints connected (Richard Zhu)
Loongson PCIe controller driver:
- Add ACPI and MCFG support for Loongson LS7A (Huacai Chen)
- Avoid config reads to non-existent LS2K/LS7A devices because a
hardware defect causes machine hangs (Huacai Chen)
- Work around LS7A integrated devices that report incorrect Interrupt
Pin values (Jianmin Lv)
Marvell Aardvark PCIe controller driver:
- Add support for AER and Slot capability on emulated bridge (Pali
Rohár)
MediaTek PCIe controller driver:
- Add Airoha EN7532 to DT binding (John Crispin)
- Allow building of driver for ARCH_AIROHA (Felix Fietkau)
MediaTek PCIe Gen3 controller driver:
- Print decoded LTSSM state when the link doesn't come up (Jianjun
Wang)
NVIDIA Tegra194 PCIe controller driver:
- Convert DT binding to json-schema (Vidya Sagar)
- Add DT bindings and driver support for Tegra234 Root Port and
Endpoint mode (Vidya Sagar)
- Fix some Root Port interrupt handling issues (Vidya Sagar)
- Set default Max Payload Size to 256 bytes (Vidya Sagar)
- Fix Data Link Feature capability programming (Vidya Sagar)
- Extend Endpoint mode support to devices beyond Controller-5 (Vidya
Sagar)
Qualcomm PCIe controller driver:
- Rework clock, reset, PHY power-on ordering to avoid hangs and
improve consistency (Robert Marko, Christian Marangi)
- Move pipe_clk handling to PHY drivers (Dmitry Baryshkov)
- Add IPQ60xx support (Selvam Sathappan Periakaruppan)
- Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru)
- Add support for more than 32 MSI interrupts (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Convert DT binding to json-schema (Herve Codina)
- Add Renesas RZ/N1D (R9A06G032) to rcar-gen2 DT binding and driver
(Herve Codina)
Samsung Exynos PCIe controller driver:
- Fix phy-exynos-pcie driver so it follows the 'phy_init() before
phy_power_on()' PHY programming model (Marek Szyprowski)
Synopsys DesignWare PCIe controller driver:
- Simplify and clean up the DWC core extensively (Serge Semin)
- Fix an issue with programming the ATU for regions that cross a 4GB
boundary (Serge Semin)
- Enable the CDM check if 'snps,enable-cdm-check' exists; previously
we skipped it if 'num-lanes' was absent (Serge Semin)
- Allocate a 32-bit DMA-able page to be MSI target instead of using a
driver data structure that may not be addressable with 32-bit
address (Will McVicker)
- Add DWC core support for more than 32 MSI interrupts (Dmitry
Baryshkov)
Xilinx Versal CPM PCIe controller driver:
- Add DT binding and driver support for Versal CPM5 Gen5 Root Port
(Bharat Kumar Gogada)"
* tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (150 commits)
PCI: imx6: Support more than Gen2 speed link mode
PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers
PCI: imx6: Reformat suspend callback to keep symmetric with resume
PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier
PCI: imx6: Disable clocks in reverse order of enable
PCI: imx6: Do not hide PHY driver callbacks and refine the error handling
PCI: imx6: Reduce resume time by only starting link if it was up before suspend
PCI: imx6: Mark the link down as non-fatal error
PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset()
PCI: imx6: Turn off regulator when system is in suspend mode
PCI: imx6: Call host init function directly in resume
PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks
PCI: imx6: Propagate .host_init() errors to caller
PCI: imx6: Collect clock enables in imx6_pcie_clk_enable()
PCI: imx6: Factor out ref clock disable to match enable
PCI: imx6: Move imx6_pcie_clk_disable() earlier
PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier
PCI: imx6: Move PHY management functions together
PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier
PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS()
...
- Drop of_match_ptr() to avoid unused variables when CONFIG_OF is unset
(Bjorn Helgaas)
- Fix ARM pci_remap_iospace() when CONFIG_MMU unset to avoid build errors
(Pali Rohár)
* pci/misc:
PCI/ACPI: Update link to PCI firmware specification
PCI: Drop of_match_ptr() to avoid unused variables
- Convert to new *_PM_OPS macros to avoid need for "#ifdef CONFIG_PM_SLEEP"
or "__maybe_unused" (Bjorn Helgaas)
* pci/ctrl/pm-ops:
PCI: Convert to new *_PM_OPS macros
- Add DT binding and driver support for Versal CPM5 Gen5 Root Port (Bharat
Kumar Gogada)
* pci/ctrl/xilinx-cpm:
MAINTAINERS: Add Xilinx Versal CPM Root Port maintainers
PCI: xilinx-cpm: Add support for Versal CPM5 Root Port
dt-bindings: PCI: xilinx-cpm: Add Versal CPM5 Root Port
- Use devm_kasprintf() instead of simple kasprintf() (Subramanian Mohan)
- Add [8086:7D0B] and [8086:AD0B] devices to VMD driver (Francisco Munoz)
* pci/ctrl/vmd:
PCI: vmd: Add DID 8086:7D0B and 8086:AD0B for Intel MTL SKUs
PCI: vmd: Use devm_kasprintf() instead of simple kasprintf()
- Fix tegra_pcie_config_ep() power management in error path (Miaoqian Lin)
- Convert DT binding to json-schema (Vidya Sagar)
- Add DT bindings and driver support for Tegra234 Root Port and Endpoint
mode (Vidya Sagar)
- Disable MSI for Tegra234 Root Ports so they use INTx for all events (PCIe
doesn't allow mixing INTx and MSI/MSI-X) (Vidya Sagar)
- Search for Vendor-Specific RAS-DEC capability instead of hard-coding
offset (Vidya Sagar)
- Fix unintentional APPL_INTR_STATUS_L0 value overwrite in Root Port
interrupt handling (Vidya Sagar)
- Clear Bandwidth Management interrupt status bit to avoid interrupt storm
(Vidya Sagar)
- Set default Max Payload Size to 256 bytes (Vidya Sagar)
- Fix offset when clearing bit in Data Link Feature capability (Vidya
Sagar)
- Extend Endpoint mode support to devices beyond Controller-5 (Vidya Sagar)
* pci/ctrl/tegra194:
PCI: tegra194: Add Tegra234 PCIe support
PCI: tegra194: Extend Endpoint mode support
PCI: tegra194: Fix link up retry sequence
PCI: tegra194: Clean up the exit path for Endpoint mode
PCI: tegra194: Enable support for 256 Byte payload
PCI: tegra194: Clear bandwidth management status
PCI: tegra194: Fix Root Port interrupt handling
PCI: tegra194: Find RAS DES PCIe capability offset
Revert "PCI: tegra194: Rename tegra_pcie_dw to tegra194_pcie"
PCI: Disable MSI for Tegra234 Root Ports
dt-bindings: PCI: tegra234: Add schema for tegra234 Endpoint mode
dt-bindings: PCI: tegra234: Add schema for tegra234 Root Port mode
dt-bindings: PCI: tegra194: Convert to json-schema
PCI: tegra194: Fix PM error handling in tegra_pcie_config_ep()
# Conflicts:
# drivers/pci/controller/dwc/pcie-designware.h
# drivers/pci/controller/dwc/pcie-tegra194.c
- Add PHY clock source implementation (Dmitry Baryshkov)
- Use new clk_regmap_phy_mux_ops for gcc-sm8450 and gcc-sc7280 PCIe pipe
clocks (Dmitry Baryshkov)
- Set up rev 2.1.0 PARF_PHY before enabling clocks (Christian Marangi)
- Power on PHY before accessing IPQ8074 DBI registers to avoid boot hangs
(Robert Marko)
- Power on PHY before accessing DBI registers on all variants for
consistency (Robert Marko)
- Remove unnecessary pipe_clk handling since this is done in PHY drivers
(Dmitry Baryshkov)
- Drop manual pipe_clk_src handling (Dmitry Baryshkov)
- Move GEN3_RELATED DBI definitions to common dwc header (Baruch Siach)
- Define slot capabilities using generic PCI_EXP_SLTCAP_* macros (Baruch
Siach)
- Add IPQ60xx support (Selvam Sathappan Periakaruppan)
- Fix DT description typo (Baruch Siach)
- Fix DT "compatibles" typo (Johan Hovold)
- Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru)
* pci/ctrl/qcom:
PCI: qcom: Allow ASPM L1 and substates for 2.7.0
dt-bindings: PCI: qcom: Fix reset conditional
dt-bindings: PCI: qcom: Fix description typo
PCI: qcom: Add IPQ60xx support
PCI: qcom: Define slot capabilities using PCI_EXP_SLTCAP_*
PCI: dwc: Move GEN3_RELATED DBI definitions to common header
PCI: qcom: Drop manual pipe_clk_src handling
PCI: qcom: Remove unnecessary pipe_clk handling
PCI: qcom: Power on PHY before DBI register accesses
PCI: qcom: Power on PHY before IPQ8074 DBI register accesses
PCI: qcom: Set up rev 2.1.0 PARF_PHY before enabling clocks
clk: qcom: gcc-sc7280: use new clk_regmap_phy_mux_ops for PCIe pipe clocks
clk: qcom: gcc-sm8450: use new clk_regmap_phy_mux_ops for PCIe pipe clocks
clk: qcom: regmap: add PHY clock source implementation
- Fix refcount leak in mtk_pcie_init_irq_domains() (Miaoqian Lin)
- Print decoded LTSSM state when the link doesn't come up (Jianjun Wang)
* pci/ctrl/mediatek-gen3:
PCI: mediatek-gen3: Print LTSSM state when PCIe link down
PCI: mediatek-gen3: Fix refcount leak in mtk_pcie_init_irq_domains()
- Add Airoha EN7532 to DT binding (John Crispin)
- Allow building of mediatek driver for ARCH_AIROHA (Felix Fietkau)
* pci/ctrl/mediatek:
PCI: mediatek: Allow building for ARCH_AIROHA
dt-bindings: PCI: mediatek: Add Airoha EN7532 support
- Wrap ARM64-specific MCFG quirks in #ifdef so Loongson can use the file
(Huacai Chen)
- Use generic (not 32-bit only) config accesses for LS2K/LS7A (Huacai Chen)
- Add ACPI and MCFG support for Loongson LS7A (Huacai Chen)
- Avoid config reads to non-existent LS2K/LS7A devices because a hardware
defect causes machine hangs (Huacai Chen)
- Work around LS7A integrated devices that report incorrect Interrupt Pin
values (Jianmin Lv)
* pci/ctrl/loongson:
PCI: loongson: Work around LS7A incorrect Interrupt Pin registers
PCI: loongson: Don't access non-existent devices
PCI: loongson: Add ACPI init support
PCI: loongson: Use generic 8/16/32-bit config ops on LS2K/LS7A
PCI/ACPI: Guard ARM64-specific mcfg_quirks
- Factor out ref clock disables to match enables (Bjorn Helgaas)
- Collect clock enables in imx6_pcie_clk_enable() (Richard Zhu)
- Propagate regulator and clock errors back to .host_init() caller (Richard
Zhu)
- Disable i.MX6QDL clock when disabling ref clocks (Richard Zhu)
- Call host init function directly in resume instead of duplicating the
code (Richard Zhu)
- Turn off regulators when suspending (Richard Zhu)
- Make link being down a non-fatal error so probe doesn't fail (Richard
Zhu)
- Start link in resume only if it was up before suspend to reduce resume
time (Richard Zhu)
- Move PHY init and power-on out of clock- and reset-related functions
(Richard Zhu)
- Rework suspend callback to be more symmetric with resume (Richard Zhu)
- Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu)
- Allow speeds faster than Gen2 (Richard Zhu)
* pci/ctrl/imx6:
PCI: imx6: Support more than Gen2 speed link mode
PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers
PCI: imx6: Reformat suspend callback to keep symmetric with resume
PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier
PCI: imx6: Disable clocks in reverse order of enable
PCI: imx6: Do not hide PHY driver callbacks and refine the error handling
PCI: imx6: Reduce resume time by only starting link if it was up before suspend
PCI: imx6: Mark the link down as non-fatal error
PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset()
PCI: imx6: Turn off regulator when system is in suspend mode
PCI: imx6: Call host init function directly in resume
PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks
PCI: imx6: Propagate .host_init() errors to caller
PCI: imx6: Collect clock enables in imx6_pcie_clk_enable()
PCI: imx6: Factor out ref clock disable to match enable
PCI: imx6: Move imx6_pcie_clk_disable() earlier
PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier
PCI: imx6: Move PHY management functions together
PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier
PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS()
- Move samsung phy-exynos-pcie init all to exynos5433_pcie_phy_init()
instead of splitting across phy_init() and phy_power_on() (Marek
Szyprowski)
- Call phy_init() before phy_power_on() for samsung phy-exynos-pcie, as
required by the PHY programming model (Marek Szyprowski)
* pci/ctrl/exynos:
PCI: exynos: Correct generic PHY usage
phy: samsung: phy-exynos-pcie: sanitize init/power_on callbacks
- Stop link on host_init errors and de-initialization (Serge Semin)
- Add support for unrolled iATU register space in dw_pcie_disable_atu()
(Serge Semin)
- Disable outbound windows only for controllers that use iATU (Serge Semin)
- Set INCREASE_REGION_SIZE flag based on limit address, not on the size,
since even a small size may cross a 4GB boundary (Serge Semin)
- Deallocate EPC memory on dw_pcie_ep_init() errors to avoid a leak (Serge
Semin)
- Always enable CDM check if "snps,enable-cdm-check" exists instead of
exiting early if the optional "num-lanes" was absent (Serge Semin)
- Simplify detection of whether we're using unrolled iATU registers (Serge
Semin)
- Make dw_pcie_link_up() more generic by using dw_pcie_readl_dbi() instead
of readl() (Serge Semin)
- Add dw_pcie_start_link() and dw_pcie_stop_link() wrappers to factor out
checks for ops being implemented (Serge Semin)
- Move io_cfg_atu_shared to struct pcie_port and rename to cfg0_io_shared,
since it's not used by dwc common code or dwc endpoint code (Serge Semin)
- Rename struct pcie_port to dw_pcie_rp to indicate that it's
DesignWare-specific (Serge Semin)
- Drop unused struct dw_plat_pcie regmap pointer (Serge Semin)
- Fix some coding style issues (Serge Semin)
- Log link speed and width if it comes up (Serge Semin)
- Save DWC IP core version in native format as read from
PORT_LOGIC.PCIE_VERSION_OFF register (Serge Semin)
- Read DWC IP core version from PORT_LOGIC.PCIE_VERSION_OFF (Serge Semin)
- Add macros to compare Synopsys IP core versions (Serge Semin)
- Drop manual DWC IP core version setup from intel-gw and tegra194 (Serge
Semin)
- Add dw_pcie_ops.host_deinit() callback (Serge Semin)
- Drop enum dw_pcie_as_type in favor of PCIE_ATU_TYPE_MEM/IO (Serge Semin)
- Drop enum dw_pcie_region_type in favor of PCIE_ATU_REGION_DIR_IB/OB
(Serge Semin)
- Simplify in/outbound iATU setup methods and reduce duplicated code (Serge
Semin)
- Detect iATU region size from hardware (Serge Semin)
- Validate iATU outbound mappings against hardware constraints (Serge
Semin)
- Check for errors in iATU setup (Serge Semin)
- Allocate a 32-bit DMA-able page to be MSI target instead of using a
driver data structure that may not be addressable with 32-bit address
(Will McVicker)
- Use the bitmap API to allocate bitmaps instead of open-coding it
(Christophe JAILLET)
- Correct dw_pcie_free_msi() checking for when to remove IRQ handler and
data (Dmitry Baryshkov)
- Split MSI init to new dw_pcie_msi_host_init() function (Dmitry Baryshkov)
- Convert struct pcie_port.msi_irq to an array so we can support more than
32 MSI interrupts (Dmitry Baryshkov)
- Handle MSIs routed to multiple GIC interrupts for Qualcomm platforms with
groups of 32 MSI vectors (Dmitry Baryshkov)
- Add additional MSI interrupts to qcom DT (Dmitry Baryshkov)
* pci/ctrl/dwc:
dt-bindings: PCI: qcom: Support additional MSI vectors
PCI: dwc: Handle MSIs routed to multiple GIC interrupts
PCI: dwc: Convert struct pcie_port.msi_irq to an array
PCI: dwc: Split MSI IRQ parsing/allocation to a separate function
PCI: dwc: Correct msi_irq condition in dw_pcie_free_msi()
PCI: dwc: Use the bitmap API to allocate bitmaps
PCI: dwc: Fix MSI msi_msg DMA mapping
PCI: dwc: Check iATU in/outbound range setup status
PCI: dwc: Validate iATU outbound mappings against hardware constraints
PCI: dwc: Add iATU regions size detection procedure
PCI: dwc: Simplify in/outbound iATU setup methods
PCI: dwc: Drop enum dw_pcie_region_type in favor of PCIE_ATU_REGION_DIR_IB/OB
PCI: dwc: Drop enum dw_pcie_as_type in favor of PCIE_ATU_TYPE_MEM/IO
PCI: dwc: Add dw_pcie_ops.host_deinit() callback
PCI: tegra194: Drop manual DW PCIe controller version setup
PCI: intel-gw: Drop manual DW PCIe controller version setup
PCI: dwc: Add macros to compare Synopsys IP core versions
PCI: dwc: Read DWC IP core version from register
PCI: dwc: Use native DWC IP core version representation
PCI: dwc: Detect iATU settings after getting "addr_space" resource
PCI: dwc: Log link speed and width if it comes up
PCI: dwc-plat: Drop dw_plat_pcie_of_match[] forward declaration
PCI: dwc-plat: Drop unused regmap pointer
PCI: dwc-plat: Simplify dw_plat_pcie_probe() return values
PCI: dwc: Rename struct pcie_port to dw_pcie_rp
PCI: dwc: Move io_cfg_atu_shared to struct pcie_port
PCI: dwc: Add start_link/stop_link inlines
PCI: dwc: Reuse local pointer to the resource data
PCI: dwc: Organize local variable usage
PCI: dwc: Convert dw_pcie_link_up() to use dw_pcie_readl_dbi()
PCI: dwc: Simplify unrolled iATU detection
PCI: dwc: Add newlines to log messages
PCI: dwc: Add braces to multi-line if-else statements
PCI: dwc: Always enable CDM check if "snps,enable-cdm-check" exists
PCI: dwc: Deallocate EPC memory on dw_pcie_ep_init() errors
PCI: dwc: Set INCREASE_REGION_SIZE flag based on limit address
PCI: dwc: Disable outbound windows only for controllers using iATU
PCI: dwc: Add unroll iATU space support to dw_pcie_disable_atu()
PCI: dwc: Stop link on host_init errors and de-initialization
- Remove unnecessary forward declarations (Jim Quinlan)
- Prevent config space access when link is down (Jim Quinlan)
- Split post-link up initialization to brcm_pcie_start_link() (Jim Quinlan)
- Enable child bus device regulators described under Root Ports in DT (Jim
Quinlan)
- Disable/enable regulators in suspend/resume (Jim Quinlan)
- Rename .map_bus() functions to end with 'map_bus' as they do in other
drivers (Jim Quinlan)
* pci/ctrl/brcmstb:
PCI: brcmstb: Rename .map_bus() functions to end with 'map_bus'
PCI: brcmstb: Disable/enable regulators in suspend/resume
PCI: brcmstb: Enable child bus device regulators from DT
PCI: brcmstb: Split post-link up initialization to brcm_pcie_start_link()
PCI: brcmstb: Prevent config space access when link is down
PCI: brcmstb: Remove unnecessary forward declarations
The PCIE_DBI_RO_WR_EN bit should be set when write some DBI registers. To
make sure that the DBI registers are writable, set the PCIE_DBI_RO_WR_EN
properly when writing the DBI registers.
Link: https://lore.kernel.org/r/1652866528-13220-1-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Create imx6_pcie_stop_link() and imx6_pcie_host_exit() functions.
Encapsulate clocks, regulators disables and PHY uninitialization into
imx6_pcie_host_exit().
To keep suspend/resume symmetric as much as possible, invoke these two
new created functions in suspend callback.
To be symmetric with imx6_pcie_host_exit(), move imx6_pcie_clk_enable()
to imx6_pcie_host_init() from imx6_pcie_deassert_core_reset().
Link: https://lore.kernel.org/r/1657783869-19194-18-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Move the imx6_pcie_ltssm_disable() earlier and place it just behind the
imx6_pcie_ltssm_enable(), since it might not be only used by suspend
callback directly.
To be symmetric with imx6_pcie_ltssm_enable(), add the IMX6Q and IMX8MQ
switch cases in imx6_pcie_ltssm_disable().
Link: https://lore.kernel.org/r/1657783869-19194-17-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
imx6_pcie_clk_enable() enables clocks in the order:
pcie_phy
pcie_bus
pcie
imx6_pcie_enable_ref_clk
Change imx6_pcie_clk_disable() to disable them in the reverse order.
Link: https://lore.kernel.org/r/1657783869-19194-16-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Move the phy_power_on() to host_init from imx6_pcie_clk_enable().
Move the phy_init() to host_init from imx6_pcie_deassert_core_reset().
Refine the error handling in imx6_pcie_host_init() accordingly.
Link: https://lore.kernel.org/r/1657783869-19194-15-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
i.MX PCIe doesn't support hotplug. During resume, only start PCIe link
training when the link was up before system suspend to avoid the long
latency in the link training period.
Link: https://lore.kernel.org/r/1657783869-19194-14-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the PCIe link is down, return zero from imx6_pcie_start_link() so the
driver will probe successfully.
Link: https://lore.kernel.org/r/1657783869-19194-13-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Move regulator enable out of imx6_pcie_deassert_core_reset(), since the
regulator_enable() has nothing to do with imx6_pcie_deassert_core_reset().
Link: https://lore.kernel.org/r/1657783869-19194-12-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The driver should undo any enables it did itself. The regulator disable
shouldn't be basing decisions on regulator_is_enabled().
Move the regulator_disable to the suspend function, turn off regulator when
the system is in suspend mode.
Link: https://lore.kernel.org/r/1657783869-19194-11-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Call imx6_pcie_host_init() instead of duplicating codes in resume. Note
that this also means we do MPLL setup again during resume, which we didn't
do before.
[bhelgaas: add MPLL setup note, pointed out by Lucas]
Link: https://lore.kernel.org/r/1657783869-19194-10-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Since dw_pcie_host_init() checks for errors from ops->host_init(),
check for errors when enabling power regulators and clocks and return them.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/1657783869-19194-8-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Encapsulate the i.MX PCIe clock enable operations into one standalone
function, imx6_pcie_clk_enable(). No functional change intended.
[bhelgaas: split pure code moves into separate patches]
Link: https://lore.kernel.org/r/1657783869-19194-7-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
The PCIe ref clocks are specific to different variants. The enables are
already split out into imx6_pcie_enable_ref_clk(), but the disables were
combined with the more generic bus/phy/pcie clock disables in
imx6_pcie_clk_disable().
Split out the variant-specific disables into imx6_pcie_disable_ref_clk() to
match imx6_pcie_enable_ref_clk().
No functional change intended.
Link: https://lore.kernel.org/r/1657783869-19194-6-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Move imx6_pcie_clk_disable() earlier to be near other clock-related
functions. No functional change intended.
[bhelgaas: reorder patch so pure moves are earlier]
Link: https://lore.kernel.org/r/1657783869-19194-5-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Move imx6_pcie_enable_ref_clk() earlier so it's not in the middle between
imx6_pcie_assert_core_reset() and imx6_pcie_deassert_core_reset(). No
functional change intended.
Link: https://lore.kernel.org/r/1657783869-19194-4-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Collect imx6_pcie_init_phy(), imx7d_pcie_wait_for_phy_pll_lock(), and
imx6_setup_phy_mpll() earlier with other PHY-related code. No functional
change intended.
Link: https://lore.kernel.org/r/1657783869-19194-3-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Move imx6_pcie_grp_offset() and imx6_pcie_configure_type() earlier in the
file since they depend on nothing and are used by several other functions
that will be moved earlier. No functional change intended.
Link: https://lore.kernel.org/r/1657783869-19194-2-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Replace SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() with NOIRQ_SYSTEM_SLEEP_PM_OPS(),
which has the advantage that the compiler always sees the PM callbacks as
referenced, so they don't need to be wrapped with "#ifdef CONFIG_PM_SLEEP"
or tagged with "__maybe_unused" to avoid "defined but not used" warnings.
See 1a3c7bb088 ("PM: core: Add new *_PM_OPS macros, deprecate old ones").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The proper initialization for generic PHYs is to call first phy_init(),
then phy_power_on().
While touching this, remove the phy_reset() call. It is just a left-over
from the obsoleted Exynos5440 support and the current exynos-pcie PHY
driver doesn't even support this function. It is also rarely used by other
drivers.
Link: https://lore.kernel.org/r/20220628220409.26545-2-m.szyprowski@samsung.com
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
On some Qualcomm platforms each group of 32 MSI vectors is routed to a
separate GIC interrupt. Implement support for such configurations by
parsing "msi0" ... "msiX" interrupts and attaching them to the chained
handler.
Note that if DT doesn't list an array of MSI interrupts and uses a single
"msi" IRQ, the driver will limit the number of supported MSI vectors to 32.
Link: https://lore.kernel.org/r/20220707134733.2436629-5-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The Qualcomm DWC PCIe controller supports more than 32 MSI interrupts, but
they are routed to separate interrupts in groups of 32 vectors. To support
this configuration, change the msi_irq field to an array. Let the DWC core
handle all interrupts that were set in this array.
[bhelgaas: reorder, drop "irq" temporary to make patch cleaner]
Link: https://lore.kernel.org/r/20220707134733.2436629-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Split handling of MSI host IRQs to a separate dw_pcie_msi_host_init()
function. The code is complex enough to warrant a separate function.
[bhelgaas: reorder patch earlier]
Link: https://lore.kernel.org/r/20220707134733.2436629-4-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The dwc-based drivers set pp->msi_irq to -ENODEV if they do not want the
dwc core to do anything with pp->msi_irq.
dw_pcie_host_init() sets the handler and data when "pp->msi_irq > 0", so
use the same condition when removing the handler and data in
dw_pcie_free_msi().
Link: https://lore.kernel.org/r/20220707134733.2436629-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
As of 07940c369a ("PCI: dwc: Fix MSI page leakage in suspend/resume"),
the PCIe designware host driver has been using the driver data allocation
for the msi_msg DMA mapping which can result in a DMA_MAPPING_ERROR due to
the DMA overflow check in dma_direct_map_page() when the address is greater
than 32 bits (reported in [1]). The commit was trying to address a memory
leak on suspend/resume by moving the MSI mapping to dw_pcie_host_init(),
but subsequently dropped the page allocation thinking it wasn't needed.
To fix the DMA mapping issue as well as make msi_msg DMA'able, switch back
to allocating a 32-bit page for the msi_msg. To avoid the suspend/resume
leak, allocate the page in dw_pcie_host_init() since that shouldn't be
called during suspend/resume.
[1] https://lore.kernel.org/all/Yo0soniFborDl7+C@google.com/
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Make the DWC PCIe RC/EP safer and more verbose for invalid or failed
inbound and outbound iATU window setups. Silently ignoring iATU regions
setup errors may cause unpredictable errors. For instance if a cfg or IO
window fails to be activated, then any CFG/IO requested won't reach target
PCIe devices and the corresponding accessors will return platform-specific
random values.
[bhelgaas: trim commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-15-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Make __dw_pcie_prog_outbound_atu() check the requested region base and size
against what the hardware can support. Return error if the region is not
correctly aligned or of a supported size.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-14-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The DWC PCIe RC/EP/DM IP core configuration parameters determine the number
of inbound and outbound iATU windows, alignment requirements (which is also
the minimum window size), minimum and maximum sizes. If internal ATU is
enabled, the former settings are determined by CX_ATU_MIN_REGION_SIZE; the
latter are determined by CX_ATU_MAX_REGION_SIZE.
Determine the required alignment and maximum size supported by the
controller and log it to help verify whether the requested inbound or
outbound memory mappings can be fully created.
Note 1. The extended iATU regions have been supported since DWC PCIe
v4.60a. There is no need in testing the upper limit register availability
for the older cores.
Note 2. The regions alignment is determined with using the fls() method
since the lower four bits of the ATU Limit register can be occupied with
the Circular Buffer Increment setting, which can be initialized with zeros.
Link: https://lore.kernel.org/r/20220624143947.8991-13-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Previously __dw_pcie_prog_outbound_atu() duplicated a lot of code between
the iatu_unroll_enabled version and the PCIE_ATU_VIEWPORT version:
__dw_pcie_prog_outbound_atu
if (iatu_unroll_enabled)
dw_pcie_prog_outbound_atu_unroll
dw_pcie_writel_ob_unroll(PCIE_ATU_UNR_LOWER_BASE, ...)
dw_pcie_writel_ob_unroll(PCIE_ATU_UNR_UPPER_BASE, ...)
...
return
dw_pcie_writel_dbi(PCIE_ATU_VIEWPORT, ...)
dw_pcie_writel_dbi(PCIE_ATU_LOWER_BASE, ...)
dw_pcie_writel_dbi(PCIE_ATU_UPPER_BASE, ...)
...
Unify those by pushing the unroll address computation and viewport
selection down into dw_pcie_writel_atu() so we can use the same
dw_pcie_writel_atu_ob() accessor for both paths:
__dw_pcie_prog_outbound_atu
dw_pcie_writel_atu_ob(PCIE_ATU_LOWER_BASE, ...)
dw_pcie_writel_atu
dw_pcie_select_atu # new
if (iatu_unroll_enabled)
return pci->atu_base + PCIE_ATU_UNROLL_BASE(...)
dw_pcie_writel_dbi(PCIE_ATU_VIEWPORT, ...)
return pci->atu_base
dw_pcie_write(base + reg)
dw_pcie_writel_atu_ob(PCIE_ATU_UPPER_BASE, ...)
...
In the non-unroll case, this does involve more MMIO writes to
PCIE_ATU_VIEWPORT, but it's mainly in initialization paths and the code
simplification is significant.
[bhelgaas: commit log, simplify dw_pcie_select_atu()]
Link: https://lore.kernel.org/r/20220624143947.8991-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously callers of dw_pcie_disable_atu() supplied enum
dw_pcie_region_type (DW_PCIE_REGION_INBOUND, DW_PCIE_REGION_OUTBOUND),
which dw_pcie_disable_atu() converted to the PCIE_ATU_REGION_DIR_IB or
PCIE_ATU_REGION_DIR_OB values needed to program the ATU registers.
Simplify the code by dropping the dw_pcie_region_type enum and passing
PCIE_ATU_REGION_DIR_IB or PCIE_ATU_REGION_DIR_OB directly.
Reorder dw_pcie_disable_atu() arguments to (dir, index) since "index"
indicates an ATU window in the regions of the corresponding direction.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Previously dw_pcie_ep_set_bar() converted the BAR PCI_BASE_ADDRESS_SPACE
bit to the internal dw_pcie_as_type enum (DW_PCIE_AS_MEM, DW_PCIE_AS_IO)
and passed it down to dw_pcie_prog_inbound_atu(), which converted the enum
to the PCIE_ATU_TYPE_MEM/PCIE_ATU_TYPE_IO values needed to program the ATU
registers.
Simplify the code by dropping the dw_pcie_as_type enum and passing
PCIE_ATU_TYPE_MEM or PCIE_ATU_TYPE_IO directly.
Reorder inbound ATU function arguments to match the outbound functions,
with address-related parameters at the end.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-10-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
dw_pcie_host_init() calls the dw_pcie_ops.host_init() callback to do
platform-specific host initialization.
Add a dw_pcie_ops.host_deinit() callback to perform the corresponding
cleanups in dw_pcie_host_deinit() and in dw_pcie_host_init() failure paths.
Link: https://lore.kernel.org/r/20220624143947.8991-9-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Since the DW PCIe common code (dw_pcie_version_detect()) now reads the IP
core version directly from the hardware, there is no point manually setting
the version for controllers newer than v4.70a.
Tegra194 only supports v4.90a, so remove the now-superfluous code that sets
struct dw_pcie.version.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220624143947.8991-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Since the DW PCIe common code (dw_pcie_version_detect()) now reads the IP
core version directly from the hardware, there is no point manually setting
the version for controllers newer than v4.70a.
Remove the now-superfluous intel-gw code that sets struct dw_pcie.version.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220624143947.8991-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add macros to compare DWC IP core versions:
dw_pcie_ver_is()
dw_pcie_ver_is_ge()
dw_pcie_ver_type_is()
dw_pcie_ver_type_is_ge()
These are along the lines of DWC3_VER_IS() and dw_spi_ver_is().
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Since DWC PCIe v4.70a, the controller version and version type can be read
from the PORT_LOGIC.PCIE_VERSION_OFF and PORT_LOGIC.PCIE_VERSION_TYPE_OFF
registers respectively.
Read the version from those registers and warn if if's different from the
version we got from the device tree.
We can only read the version after platform-specific drivers have done any
DBI-related initialization, such as reference clock activation.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Save the DWC IP core version in the same format as the
PORT_LOGIC.PCIE_VERSION_OFF register, similar to what other drivers for DWC
IP do (dw_spi_hw_init(), dwc3_core_is_valid(), stmmac_hwif_init()).
[bhelgaas: trim commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Printing just "link up" isn't very informative for PCI Express. Even if the
link is up, bus performance can degrade to slower speeds or to narrower
width than both Root Port and its partner is capable of. In that case it
would be handy to know the link specifications as early as possible.
If the link comes up, log the link speed (PCIe generation) and width.
Link: https://lore.kernel.org/r/20220624143947.8991-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Allow ASPM L1 and its substates. By default this is disabled in the qcom
specific hardware. Enable it explicitly only for controllers belonging to
2_7_0.
This does not affect any link capability registers; it will allow the link
transitions to L1 and its substates only if they are already supported.
Link: https://lore.kernel.org/r/1657886366-32685-1-git-send-email-quic_krichai@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Replace SET_*_PM_OPS with *_PM_OPS, which which have the advantage that the
compiler always sees the PM callbacks as referenced, so they don't need to
be wrapped with "#ifdef CONFIG_PM_SLEEP" or tagged with "__maybe_unused" to
avoid "defined but not used" warnings.
See 1a3c7bb088 ("PM: core: Add new *_PM_OPS macros, deprecate old ones").
Link: https://lore.kernel.org/r/20220719215108.1583108-1-helgaas@kernel.org
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org> # pci-mvebu.c
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Rename the .map_bus() functions to end with 'map_bus' so they're easy to
find with, e.g., 'git grep "^static.*_map_bus" drivers/pci/'.
[bhelgaas: rename brcm_pcie_map_bus32() to brcm7425_pcie_map_bus() for
better cscope-ability (".*_map_bus" is not the same as ".*_map_bus.*")]
Link: https://lore.kernel.org/r/20220725151258.42574-8-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
If we found power regulators for a device below the Root Port, disable them
during suspend and re-enable them during resume.
If any downstream device can be a wakeup device, do not turn off the
regulators as the device will need them on.
[bhelgaas: drop unused regulator_oops, skip wrapping of .add_bus()/
.remove_bus(), move brcm_pcie_start_link() to .add_bus() in previous patch,
squash WOL checking into this patch]
Link: https://lore.kernel.org/r/20220725151258.42574-6-jim2101024@gmail.com
Link: https://lore.kernel.org/r/20220725151258.42574-7-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Some platforms have power regulators for slots or devices below Root Ports.
On platforms like Raspberry Pi 4, these regulators are described in the
Root Port device tree node, since they logically belong to the Root Port,
not to the host bridge itself.
Add an .add_bus() hook (called when pci_alloc_child_bus() allocates the
secondary ("child") bus for a bridge), and look for such regulators. If we
find some, enable them before bringing up the link and enumerating devices
on the child bus.
Similarly, when pci_remove_bus() calls the ops->remove_bus() hook, disable
the regulators.
The regulators that may be described in a Root Port DT device are:
vpcie3v3
vpcie3v3aux
vpcie12v
These control power to the device downstream from the Root Port.
[bhelgaas: commit log, name hooks brcm_pcie_add_bus(), etc, since we only
support one set of subregulator info, save info in struct brcm_pcie instead
of dev->driver_data, move brcm_pcie_start_link() from probe to .add_bus()
(from subsequent patch)]
Link: https://lore.kernel.org/r/20220725151258.42574-5-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Previously brcm_pcie_setup() initialized the Root Port itself as well as
doing the actual link-up. Split brcm_pcie_setup() into two functions:
- brcm_pcie_setup(), which initializes everything that does not require
the link itself to be up, and
- brcm_pcie_start_link(), which brings up the link and initializes things
that depend on the link being up.
[bhelgaas: condense commit log, deferring details for future changes]
Link: https://lore.kernel.org/r/20220725151258.42574-3-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
When the link is down, config accesses to downstream devices cause CPU
aborts. Allow config accesses only when the link is up.
As the following scenario shows, this check is racy and cannot completely
avoid CPU aborts, but it makes them less likely:
pci_generic_config_read
addr = brcm_pcie_map_conf # bus->ops->map_bus()
brcm_pcie_link_up # returns "true"; link is up
<link goes down>
*val = readb(addr) # link is now down
<CPU abort>
Note that config space accesses to the Root Port are not affected by link
status.
[bhelgaas: commit log, use PCIE_ECAM_REG() instead of magic 0xfff masks;
note that pci_generic_config_read32() masks low two bits already]
Link: https://lore.kernel.org/r/20220725151258.42574-4-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Remove forward function declarations in this driver. Also move some
constant structure definitions lower in the file. There are no changes to
the code that has been moved.
Link: https://lore.kernel.org/r/20220725151258.42574-2-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Add support for Synopsys DesignWare core IP based PCIe host controllers
present in the Tegra234 SoC.
Link: https://lore.kernel.org/r/20220721142052.25971-17-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since only Controller-5 can be used in the Endpoint mode in P2972-0000
platform, support is available only for Controller-5.
Extend that support by enabling the Endpoint mode capable controller during
initialization which otherwise is not required if it is only Controller-5.
Link: https://lore.kernel.org/r/20220721142052.25971-16-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Set 256 byte payload as the default in the Device Control Register to allow
the PCIe subsystem to enable 256 byte Max Payload Size when a capable link
partner is connected.
Link: https://lore.kernel.org/r/20220721142052.25971-13-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In the event of a bandwidth management interrupt, clear the bandwidth
management status in the configuration space also along with clearing
corresponding status in the application logic register to avoid slew
of interrupts.
Link: https://lore.kernel.org/r/20220721142052.25971-12-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
As part of Root Port interrupt handling, level-0 register is read first and
based on the bits set in that, corresponding level-1 registers are read for
further interrupt processing. Since both these values are currently read
into the same 'val' variable, checking level-0 bits the second time around
is happening on the 'val' variable value of level-1 register contents
instead of freshly reading the level-0 value again.
Fix by using different variables to store level-0 and level-1 registers
contents.
Link: https://lore.kernel.org/r/20220721142052.25971-11-vidyas@nvidia.com
Fixes: 56e15a238d ("PCI: tegra: Add Tegra194 PCIe support")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit b572569183.
Revert b572569183 ("PCI: tegra194: Rename tegra_pcie_dw to
tegra194_pcie") to keep the names of data structures generic and not
contain any one particular chip name. This is a preparatory change for the
upcoming changes that add support for Tegra234. This has no functional
impact.
Link: https://lore.kernel.org/r/20220721142052.25971-9-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Xilinx Versal Premium series has CPM5 block which supports Root Port
functioning at Gen5 speed.
Xilinx Versal CPM5 has a few changes from the existing CPM block:
- CPM5 has dedicated register space for control and status registers.
- CPM5 legacy interrupt handling needs additional register bit to enable
and handle legacy interrupts.
Add support for the new CPM5 features.
[bhelgaas: compare variant->version with CPM5 explicitly]
Link: https://lore.kernel.org/r/20220705105646.16980-3-bharat.kumar.gogada@xilinx.com
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Several devices integrated into LS7A report 1 (which means they use
INTA) in their Interrupt Pin registers, but they actually use a different
interrupt.
Add a quirk to override the incorrect Interrupt Pin values.
This is only needed by ACPI-based systems. For DT-based systems,
pci_assign_irq() ignores the Interrupt Pin register except to learn that
the device uses INTx and the host bridge .map_irq() function
(loongson_map_irq()) learns the IRQ mapping via DT and of_irq_parse_pci().
[bhelgaas: drop PCIE_PORT_x, OHCI, GPU since they are function 0 and don't
need the quirk, squash in updates from
https://lore.kernel.org/r/CAAhV-H40_o+9KS1t67O98GusM38pDaiB4bssxd3KQZpAByfnLg@mail.gmail.com]
Link: https://lore.kernel.org/r/20220714124216.1489304-8-chenhuacai@loongson.cn
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
fu740 uses no syscon or regman interfaces, so it doesn't need to include
mfs/syscon.h. It uses no regulator interfaces, so it doesn't need to
include regulator/consumer.h either.
Remove both unnecessary includes.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
platform.
The code is based on downstream[1] Codeaurora kernel v5.4 (branch
win.linuxopenwrt.2.0).
Split out the DBI registers access part from .init into .post_init. DBI
registers are only accessible after phy_power_on().
[1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/
Link: https://lore.kernel.org/r/f7f848653c99abbf9a0f877949a44e52329543ae.1655799816.git.baruch@tkos.co.il
Tested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The PCIE_CAP_LINK1_VAL macro actually defines slot capabilities. Use
PCI_EXP_SLTCAP_* macros to spell its value, and rename it to better
describe its meaning.
Link: https://lore.kernel.org/r/3025d5e1d8da64798db6958f9780c4763fbcac47.1655799816.git.baruch@tkos.co.il
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Manual reparenting of pipe_clk_src is being replaced with the parking of
the clock with clk_disable()/clk_enable() in the PHY driver. Drop
redundant code switching of the pipe clock between the PHY clock source
and the safe bi_tcxo.
Link: https://lore.kernel.org/r/20220608105238.2973600-6-dmitry.baryshkov@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
On LS2K/LS7A, config reads to some non-existent devices don't return
0xffffffff (they are hidden devices for debug, and accessing the config
space may cause machine hang). This is a hardware flaw but we can only
avoid it by software now.
Link: https://lore.kernel.org/r/20220714124216.1489304-5-chenhuacai@loongson.cn
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Loongson PCH (LS7A chipset) will be used by both MIPS-based and LoongArch-
based Loongson processors. MIPS-based Loongson uses FDT, while LoongArch-
based Loongson uses ACPI.
Add ACPI init support for the driver in pci-loongson.c because it is
currently FDT-only.
LoongArch is a new RISC ISA, mainline support will come soon, and
documentations are here (in translation):
https://github.com/loongson/LoongArch-Documentation
Link: https://lore.kernel.org/r/20220714124216.1489304-4-chenhuacai@loongson.cn
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
LS2K/LS7A support 8/16/32-bits PCI config access operations via CFG1, so
we can disable CFG0 for them and safely use pci_generic_config_read()/
pci_generic_config_write() instead of pci_generic_config_read32()/pci_
generic_config_write32().
Link: https://lore.kernel.org/r/20220714124216.1489304-3-chenhuacai@loongson.cn
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe PHY drivers (both QMP and PCIe2) already do clk_prepare_enable() /
clk_prepare_disable() pipe_clk. Remove extra calls to enable/disable
this clock from the PCIe driver, so that the PHY driver can manage the
clock on its own.
[bhelgaas: rebase on Robert Marko's DBI cleanup:
https://lore.kernel.org/r/20220623155004.688090-2-robimarko@gmail.com]
Link: https://lore.kernel.org/r/20220608105238.2973600-5-dmitry.baryshkov@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
IPQ8074 requires the PHY to be powered on before accessing DBI registers.
It's not clear whether other variants have the same dependency, but there
seems to be no reason for them to be different, so move all the DBI
accesses from .init() to .post_init() so they are all after phy_power_on().
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220623155004.688090-2-robimarko@gmail.com
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently the Gen2 port in IPQ8074 will cause the system to hang as it
accesses DBI registers in qcom_pcie_init_2_3_3(), and those are only
accesible after phy_power_on().
Move the DBI read/writes to a new qcom_pcie_post_init_2_3_3(), which is
executed after phy_power_on().
Link: https://lore.kernel.org/r/20220623155004.688090-1-robimarko@gmail.com
Fixes: a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: stable@vger.kernel.org # v5.11+
We currently enable clocks BEFORE we write to PARF_PHY_CTRL reg to enable
clocks and resets. This causes the driver to never set to a ready state
with the error 'Phy link never came up'.
This is caused by the PHY clock getting enabled before setting the required
bits in the PARF regs.
A workaround for this was set but with this new discovery we can drop
the workaround and use a proper solution to the problem by just enabling
the clock only AFTER the PARF_PHY_CTRL bit is set.
This correctly sets up the PCIe link and makes it usable even when a
bootloader leaves the PCIe link in an undefined state.
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Link: https://lore.kernel.org/r/20220708222743.27019-1-ansuelsmth@gmail.com
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The cpumask that is passed to this function ultimately comes from
irq_data_get_effective_affinity_mask(), which was recently changed to
return a const cpumask pointer. The first level of functions handling
the affinity mask were updated, but not this helper function.
Fixes: 4d0b829881 ("genirq: Return a const cpumask from irq_data_get_affinity_mask")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220708004931.1672-1-samuel@sholland.org
Now that the irq_data_update_affinity helper exists, enforce its use
by returning a a const cpumask from irq_data_get_affinity_mask.
Since the previous commit already updated places that needed to call
irq_data_update_affinity, this commit updates the remaining code that
either did not modify the cpumask or immediately passed the modified
mask to irq_set_affinity.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220701200056.46555-8-samuel@sholland.org
We have stubs for most OF interfaces even when CONFIG_OF is not set, so we
allow building of most controller drivers in that case for compile testing.
When CONFIG_OF is not set, "of_match_ptr(<match_table>)" compiles to NULL,
which leaves <match_table> unused, resulting in errors like this:
$ make W=1
drivers/pci/controller/pci-xgene.c:636:34: error: ‘xgene_pcie_match_table’ defined but not used [-Werror=unused-const-variable=]
Drop of_match_ptr() to avoid the unused variable warning.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The dw_plat_pcie_of_match[] forward declaration was required when
dw_plat_pcie_probe() called of_match_device(). 5c204204cf ("PCI:
designware-plat: Prefer of_device_get_match_data()") replaced that with
of_device_get_match_data(), which no longer needs the declaration.
Drop the unnecessary forward declaration.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143428.8334-19-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
1d906b2207 ("PCI: dwc: Add support for EP mode") added the struct
dw_plat_pcie regmap pointer, but it has never been used. Remove it.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143428.8334-18-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Save the return value in "ret" for all three cases (DW_PCIE_RC_TYPE,
DW_PCIE_EP_TYPE, default) handled by dw_plat_pcie_probe() and return from a
single place.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143428.8334-17-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
All of the DW PCIe core driver entities except the pcie_port struct have
names with the "dw_" prefix to distinguish local and common PCIe name
spaces, and endpoint-related entities have an "_ep" suffix.
Rename struct pcie_port to dw_pcie_rp to make it more consistent with other
names.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143428.8334-16-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
The io_cfg_atu_shared flag is set if there is an outbound iATU window used
for both config space accesses and IO port transfers.
Since the flag semantic is purely Root Port specific, it's not used in
either the DW PCIe common code or in the DW PCIe Endpoint driver. Move it
to the struct pcie_port and rename to cfg0_io_shared.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143428.8334-15-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Factor out this pattern:
if (!pci->ops || !pci->ops->start_link)
return -EINVAL;
return pci->ops->start_link(pci);
into a new dw_pcie_start_link() wrapper and do the same for the stop_link()
method.
Note that dw_pcie_ep_start() previously returned -EINVAL if there was no
platform start_link() method, which didn't make much sense since that is
not an error. It will now return 0 in that case.
As a side-effect, drop the empty start_link() and dummy dw_pcie_ops
instances from the generic DW PCIe and Layerscape EP platform drivers.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143428.8334-14-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
dw_pcie_host_init() has two instances of the resource structure pointers
used in unrelated places. It's pointless to have two different local
storages for them since the corresponding code is small and having
resource-specific names doesn't make it more readable.
Convert these parts of the function to use a common pointer to the
resource structure instance.
Link: https://lore.kernel.org/r/20220624143428.8334-13-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There are several places in the common DW PCIe code with incoherent local
variable usage: a variable is defined and initialized with a structure
field, but the structure pointer is dereferenced to access that field
anyway; the local variable is defined and initialized but either used just
once or not used afterwards in the main part of the subsequent method. It
mainly concerns the pcie_port.dev field. Fix that in the relevant places.
Link: https://lore.kernel.org/r/20220624143428.8334-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
While the rest of the generic DWC PCIe code uses the dedicated IO-mem
accessors, the dw_pcie_link_up() method for some unobvious reason directly
calls readl() to get PortLogic.DEBUG1 register content. Since the way the
DBI bus is accessed can be platform-specific, use dw_pcie_readl_dbi()
instead so dw_pcie_link_up() is slightly more generic.
Link: https://lore.kernel.org/r/20220624143428.8334-11-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
The unrolled version of the internal ATU has been available since the DWC
PCIe v4.80a IP core, but it may not be enabled. Per [1], if unrolled ATU
is enabled, the PCIE_ATU_VIEWPORT does not exist and reads as 0xffffffff;
while if unrolled ATU is disabled, PCIE_ATU_VIEWPORT will contain some
zeros.
Simplify dw_pcie_iatu_unroll_enabled() by checking the value of
PCIE_ATU_VIEWPORT.
[1] DesignWare Cores, PCI Express Controller, Register Desciptions,
v.4.90a, December 2016, p.855
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143428.8334-10-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
If the "snps,enable-cdm-check" property exists, we should enable the CDM
check. But previously dw_pcie_setup() could exit before doing so if the
"num-lanes" property was absent or invalid.
Move the CDM enable earlier so we do it regardless of whether "num-lanes"
is present.
[bhelgaas: commit log]
Fixes: 07f123def7 ("PCI: dwc: Add support to enable CDM register check")
Link: https://lore.kernel.org/r/20220624143428.8334-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If dw_pcie_ep_init() fails to perform any action after the EPC memory is
initialized and the MSI memory region is allocated, the latter parts won't
be undone thus causing a memory leak. Add a cleanup-on-error path to fix
these leaks.
[bhelgaas: commit log]
Fixes: 2fd0c9d966 ("PCI: designware-ep: Pre-allocate memory for MSI in dw_pcie_ep_init")
Link: https://lore.kernel.org/r/20220624143428.8334-6-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
We program the 64-bit ATU limit address (in PCIE_ATU_LIMIT/
PCIE_ATU_UPPER_LIMIT or PCIE_ATU_UNR_LOWER_LIMIT/PCIE_ATU_UNR_UPPER_LIMIT),
but in addition, the PCIE_ATU_INCREASE_REGION_SIZE bit must be set if the
upper 32 bits of the limit address differ from the upper 32 bits of the
base address (see [1,2]).
5b4cf0f653 ("PCI: dwc: Add upper limit address for outbound iATU") set
PCIE_ATU_INCREASE_REGION_SIZE, but only when the *size* was greater than
4GB. It did not set it when a smaller region crossed a 4GB boundary, e.g.,
[mem 0x0_f0000000-0x1_0fffffff].
Set PCIE_ATU_INCREASE_REGION_SIZE whenever PCIE_ATU_UPPER_LIMIT is
greater than PCIE_ATU_UPPER_BASE.
[1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
v5.40a, March 2019, fig.3-36, p.175
[2] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
v5.40a, March 2019, fig.3-37, p.176
[bhelgaas: commit log]
Fixes: 5b4cf0f653 ("PCI: dwc: Add upper limit address for outbound iATU")
Link: https://lore.kernel.org/r/20220624143428.8334-5-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Some DWC-based controllers (e.g., pcie-al.c and pci-keystone.c, identified
by the fact that they override the default dw_child_pcie_ops) use their own
address translation approach instead of the DWC internal ATU (iATU). For
those controllers, skip disabling the iATU outbound windows.
[bhelgaas: commit log, update multiple window comment]
Fixes: 458ad06c4c ("PCI: dwc: Ensure all outbound ATU windows are reset")
Link: https://lore.kernel.org/r/20220624143428.8334-4-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
dw_pcie_disable_atu() was introduced by f8aed6ec62 ("PCI: dwc:
designware: Add EP mode support") and supported only the viewport version
of the iATU CSRs.
DW PCIe IP cores v4.80a and newer also support unrolled iATU/eDMA space.
Callers of dw_pcie_disable_atu(), including pci_epc_ops.clear_bar(),
pci_epc_ops.unmap_addr(), and dw_pcie_setup_rc(), don't work correctly when
it is enabled.
Add dw_pcie_disable_atu() support for controllers with unrolled iATU CSRs
enabled.
[bhelgaas: commit log]
Fixes: f8aed6ec62 ("PCI: dwc: designware: Add EP mode support")
Link: https://lore.kernel.org/r/20220624143428.8334-3-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
It's logically correct to undo everything that was done when an error is
discovered or in the corresponding cleanup counterpart. Otherwise the host
controller will be left in an undetermined state. Since the link is set up
in the host_init method, deactivate it there in the cleanup-on-error block
and stop the link in the antagonistic routine - dw_pcie_host_deinit(). Link
deactivation is platform-specific and should be implemented in
dw_pcie_ops.stop_link().
Fixes: 886a9c1347 ("PCI: dwc: Move link handling into common code")
Link: https://lore.kernel.org/r/20220624143428.8334-2-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Add support for VMD devices in MTL-H/P/U/S/M with bus restriction mode and
vector 0 disabled for MSI-X remapping.
Link: https://lore.kernel.org/r/20220628221023.190547-1-francisco.munoz.ruiz@linux.intel.com
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Add Renesas RZ/N1 SOC family support to the Renesas R-Car Gen2 PCI bridge
driver.
The Renesas RZ/N1 SOC internal PCI bridge is compatible with the one in the
R-Car Gen2 family.
Tested with the RZ/N1D (R9A06G032) SOC.
Link: https://lore.kernel.org/r/20220520094155.313784-4-herve.codina@bootlin.com
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Print current LTSSM state when PCIe link down instead of the register
value to make it easier to get the link status.
Link: https://lore.kernel.org/r/20220329030715.7975-1-jianjun.wang@mediatek.com
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Allow selecting the pcie-mediatek driver if ARCH_AIROHA is set, because the
Airoha EN7523 SoC uses the same controller as MT7622.
The driver itself is not modified. The PCIe controller DT node should use
mediatek,mt7622-pcie after airoha,en7523-pcie.
Link: https://lore.kernel.org/r/20220615125335.96089-2-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Slot capabilities are currently not reported because emulated bridge does
not report the PCI_EXP_FLAGS_SLOT flag.
Set PCI_EXP_FLAGS_SLOT to let the kernel know that PCI_EXP_SLT* registers
are supported.
Move setting of PCI_EXP_SLTCTL register from "dynamic" pcie_conf_read
function to static buffer as it is only statically filled the
PCI_EXP_SLTSTA_PDS flag and dynamic read callback is not needed for this
register.
Set Presence State Bit to 1 since there is no support for unplugging the
card and there is currently no platform able to detect presence of a card -
in such a case the bit needs to be set to 1.
Finally correctly set Physical Slot Number to 1 since there is only one
port and zero value is reserved for ports within the same silicon as Root
Port which is not our case for Aardvark HW.
Link: https://lore.kernel.org/r/20220524132827.8837-3-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Aardvark controller supports Advanced Error Reporting configuration
registers.
Export these registers on the emulated root bridge via new .read_ext() and
.write_ext() methods.
Note that in the Advanced Error Reporting Capability header the offset to
the next Extended Capability header is set, but it is not documented in
Armada 3700 Functional Specification. Since this change adds support only
for Advanced Error Reporting, explicitly clear PCI_EXT_CAP_NEXT bits in AER
capability header.
Now the pcieport driver correctly detects AER support and allows PCIe AER
driver to start receiving ERR interrupts. Kernel log now says:
pcieport 0000:00:00.0: AER: enabled with IRQ 52
Link: https://lore.kernel.org/r/20220524132827.8837-2-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
of_get_child_by_name() returns a node pointer with refcount incremented, so
we should use of_node_put() on it when we don't need it anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 814cceebba ("PCI: mediatek-gen3: Add INTx support")
Link: https://lore.kernel.org/r/20220601041259.56185-1-linmq006@gmail.com
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
pm_runtime_enable() will increase power disable depth. If
dw_pcie_ep_init() fails, we should use pm_runtime_disable() to balance it
with pm_runtime_enable().
Add missing pm_runtime_disable() for tegra_pcie_config_ep().
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Link: https://lore.kernel.org/r/20220602031910.55859-1-linmq006@gmail.com
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
of_get_next_child() returns a node pointer with refcount incremented, so we
should use of_node_put() on it when we don't need it anymore.
mc_pcie_init_irq_domains() only calls of_node_put() in the normal path,
missing it in some error paths. Add missing of_node_put() to avoid
refcount leak.
Fixes: 6f15a9c9f9 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Link: https://lore.kernel.org/r/20220605055123.59127-1-linmq006@gmail.com
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----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=4NaF
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci fixes from Bjorn Helgaas:
- Revert brcmstb patches that broke booting on Raspberry Pi Compute
Module 4 (Bjorn Helgaas)
- Fix bridge_d3_blacklist[] error that overwrote the existing Gigabyte
X299 entry instead of adding a new one (Bjorn Helgaas)
- Update Lorenzo Pieralisi's email address in MAINTAINERS (Lorenzo
Pieralisi)
* tag 'pci-v5.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Update Lorenzo Pieralisi's email address
PCI/PM: Fix bridge_d3_blacklist[] Elo i2 overwrite of Gigabyte X299
Revert "PCI: brcmstb: Split brcm_pcie_setup() into two funcs"
Revert "PCI: brcmstb: Add mechanism to turn on subdev regulators"
Revert "PCI: brcmstb: Add control of subdevice voltage regulators"
Revert "PCI: brcmstb: Do not turn off WOL regulators on suspend"
This reverts commit 830aa6f29f.
This is part of a revert of the following commits:
11ed8b8624 ("PCI: brcmstb: Do not turn off WOL regulators on suspend")
93e41f3fca ("PCI: brcmstb: Add control of subdevice voltage regulators")
67211aadcb ("PCI: brcmstb: Add mechanism to turn on subdev regulators")
830aa6f29f ("PCI: brcmstb: Split brcm_pcie_setup() into two funcs")
Cyril reported that 830aa6f29f ("PCI: brcmstb: Split brcm_pcie_setup()
into two funcs"), which appeared in v5.17-rc1, broke booting on the
Raspberry Pi Compute Module 4. Apparently 830aa6f29f panics with an
Asynchronous SError Interrupt, and after further commits here is a black
screen on HDMI and no output on the serial console.
This does not seem to affect the Raspberry Pi 4 B.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215925
Link: https://lore.kernel.org/r/20220511201856.808690-5-helgaas@kernel.org
Reported-by: Cyril Brulebois <kibi@debian.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit 67211aadcb.
This is part of a revert of the following commits:
11ed8b8624 ("PCI: brcmstb: Do not turn off WOL regulators on suspend")
93e41f3fca ("PCI: brcmstb: Add control of subdevice voltage regulators")
67211aadcb ("PCI: brcmstb: Add mechanism to turn on subdev regulators")
830aa6f29f ("PCI: brcmstb: Split brcm_pcie_setup() into two funcs")
Cyril reported that 830aa6f29f ("PCI: brcmstb: Split brcm_pcie_setup()
into two funcs"), which appeared in v5.17-rc1, broke booting on the
Raspberry Pi Compute Module 4. Apparently 830aa6f29f panics with an
Asynchronous SError Interrupt, and after further commits here is a black
screen on HDMI and no output on the serial console.
This does not seem to affect the Raspberry Pi 4 B.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215925
Link: https://lore.kernel.org/r/20220511201856.808690-4-helgaas@kernel.org
Reported-by: Cyril Brulebois <kibi@debian.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit 93e41f3fca.
This is part of a revert of the following commits:
11ed8b8624 ("PCI: brcmstb: Do not turn off WOL regulators on suspend")
93e41f3fca ("PCI: brcmstb: Add control of subdevice voltage regulators")
67211aadcb ("PCI: brcmstb: Add mechanism to turn on subdev regulators")
830aa6f29f ("PCI: brcmstb: Split brcm_pcie_setup() into two funcs")
Cyril reported that 830aa6f29f ("PCI: brcmstb: Split brcm_pcie_setup()
into two funcs"), which appeared in v5.17-rc1, broke booting on the
Raspberry Pi Compute Module 4. Apparently 830aa6f29f panics with an
Asynchronous SError Interrupt, and after further commits here is a black
screen on HDMI and no output on the serial console.
This does not seem to affect the Raspberry Pi 4 B.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215925
Link: https://lore.kernel.org/r/20220511201856.808690-3-helgaas@kernel.org
Reported-by: Cyril Brulebois <kibi@debian.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit 11ed8b8624.
This is part of a revert of the following commits:
11ed8b8624 ("PCI: brcmstb: Do not turn off WOL regulators on suspend")
93e41f3fca ("PCI: brcmstb: Add control of subdevice voltage regulators")
67211aadcb ("PCI: brcmstb: Add mechanism to turn on subdev regulators")
830aa6f29f ("PCI: brcmstb: Split brcm_pcie_setup() into two funcs")
Cyril reported that 830aa6f29f ("PCI: brcmstb: Split brcm_pcie_setup()
into two funcs"), which appeared in v5.17-rc1, broke booting on the
Raspberry Pi Compute Module 4. Apparently 830aa6f29f panics with an
Asynchronous SError Interrupt, and after further commits here is a black
screen on HDMI and no output on the serial console.
This does not seem to affect the Raspberry Pi 4 B.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215925
Link: https://lore.kernel.org/r/20220511201856.808690-2-helgaas@kernel.org
Reported-by: Cyril Brulebois <kibi@debian.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAmKSSbcTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXgJyCACeyMOcFws5lyqqdk0R0zGr2KFfKsJn
YQR9nvldT2p/1y0ykvU208UIq0HHmXOb9pD8gOUzGYGp4XlEaC1f4V37mmzgLcRu
vL/HcFqBl2cQEfaQxiXZrmsIIVszwbc57EGqpl93cS2er4hp/NXmredKCId7Mpt8
FjxjgVGzdhEUKbJZYjkDM5pYAnJ9QVwuK3MaarKMK86Oj1P5YtKgIb4ZSt/NHvsC
Mukx3nivSH29XfK3fRsFDJUQr9WNYh1cmTtyhB0tWVXQCYFc4angZRtCJwyXzkp2
P5GBIQoMZcXX2XWkUBTtA1w5g/aZZsBExb3YGhQjsQP+jb6MtDnvOEo9
=Z2E+
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed-20220528' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv updates from Wei Liu:
- Harden hv_sock driver (Andrea Parri)
- Harden Hyper-V PCI driver (Andrea Parri)
- Fix multi-MSI for Hyper-V PCI driver (Jeffrey Hugo)
- Fix Hyper-V PCI to reduce boot time (Dexuan Cui)
- Remove code for long EOL'ed Hyper-V versions (Michael Kelley, Saurabh
Sengar)
- Fix balloon driver error handling (Shradha Gupta)
- Fix a typo in vmbus driver (Julia Lawall)
- Ignore vmbus IMC device (Michael Kelley)
- Add a new error message to Hyper-V DRM driver (Saurabh Sengar)
* tag 'hyperv-next-signed-20220528' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: (28 commits)
hv_balloon: Fix balloon_probe() and balloon_remove() error handling
scsi: storvsc: Removing Pre Win8 related logic
Drivers: hv: vmbus: fix typo in comment
PCI: hv: Fix synchronization between channel callback and hv_pci_bus_exit()
PCI: hv: Add validation for untrusted Hyper-V values
PCI: hv: Fix interrupt mapping for multi-MSI
PCI: hv: Reuse existing IRTE allocation in compose_msi_msg()
drm/hyperv: Remove support for Hyper-V 2008 and 2008R2/Win7
video: hyperv_fb: Remove support for Hyper-V 2008 and 2008R2/Win7
scsi: storvsc: Remove support for Hyper-V 2008 and 2008R2/Win7
Drivers: hv: vmbus: Remove support for Hyper-V 2008 and Hyper-V 2008R2/Win7
x86/hyperv: Disable hardlockup detector by default in Hyper-V guests
drm/hyperv: Add error message for fb size greater than allocated
PCI: hv: Do not set PCI_COMMAND_MEMORY to reduce VM boot time
PCI: hv: Fix hv_arch_irq_unmask() for multi-MSI
Drivers: hv: vmbus: Refactor the ring-buffer iterator functions
Drivers: hv: vmbus: Accept hv_sock offers in isolated guests
hv_sock: Add validation for untrusted Hyper-V values
hv_sock: Copy packets sent by Hyper-V out of the ring buffer
hv_sock: Check hv_pkt_iter_first_raw()'s return value
...
-----BEGIN PGP SIGNATURE-----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=hEti
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Resource management:
- Restrict E820 clipping to PCI host bridge windows (Bjorn Helgaas)
- Log E820 clipping better (Bjorn Helgaas)
- Add kernel cmdline options to enable/disable E820 clipping (Hans de
Goede)
- Disable E820 reserved region clipping for IdeaPads, Yoga, Yoga
Slip, Acer Spin 5, Clevo Barebone systems where clipping leaves no
usable address space for touchpads, Thunderbolt devices, etc (Hans
de Goede)
- Disable E820 clipping by default starting in 2023 (Hans de Goede)
PCI device hotplug:
- Include files to remove implicit dependencies (Christophe Leroy)
- Only put Root Ports in D3 if they can signal and wake from D3 so
AMD Yellow Carp doesn't miss hotplug events (Mario Limonciello)
Power management:
- Define pci_restore_standard_config() only for CONFIG_PM_SLEEP since
it's unused otherwise (Krzysztof Kozlowski)
- Power up devices completely, including anything platform firmware
needs to do, during runtime resume (Rafael J. Wysocki)
- Move pci_resume_bus() to PM callbacks so we observe the required
bridge power-up delays (Rafael J. Wysocki)
- Drop unneeded runtime_d3cold device flag (Rafael J. Wysocki)
- Split pci_raw_set_power_state() between pci_power_up() and a new
pci_set_low_power_state() (Rafael J. Wysocki)
- Set current_state to D3cold if config read returns ~0, indicating
the device is not accessible (Rafael J. Wysocki)
- Do not call pci_update_current_state() from pci_power_up() so BARs
and ASPM config are restored correctly (Rafael J. Wysocki)
- Write 0 to PMCSR in pci_power_up() in all cases (Rafael J. Wysocki)
- Split pci_power_up() to pci_set_full_power_state() to avoid some
redundant operations (Rafael J. Wysocki)
- Skip restoring BARs if device is not in D0 (Rafael J. Wysocki)
- Rearrange and clarify pci_set_power_state() (Rafael J. Wysocki)
- Remove redundant BAR restores from pci_pm_thaw_noirq() (Rafael J.
Wysocki)
Virtualization:
- Acquire device lock before config space access lock to avoid AB/BA
deadlock with sriov_numvfs_store() (Yicong Yang)
Error handling:
- Clear MULTI_ERR_COR/UNCOR_RCV bits, which a race could previously
leave permanently set (Kuppuswamy Sathyanarayanan)
Peer-to-peer DMA:
- Whitelist Intel Skylake-E Root Ports regardless of which devfn they
are (Shlomo Pongratz)
ASPM:
- Override L1 acceptable latency advertised by Intel DG2 so ASPM L1
can be enabled (Mika Westerberg)
Cadence PCIe controller driver:
- Set up device-specific register to allow PTM Responder to be
enabled by the normal architected bit (Christian Gmeiner)
- Override advertised FLR support since the controller doesn't
implement FLR correctly (Parshuram Thombare)
Cadence PCIe endpoint driver:
- Correct bitmap size for the ob_region_map of outbound window usage
(Dan Carpenter)
Freescale i.MX6 PCIe controller driver:
- Fix PERST# assertion/deassertion so we observe the required delays
before accessing device (Francesco Dolcini)
Freescale Layerscape PCIe controller driver:
- Add "big-endian" DT property (Hou Zhiqiang)
- Update SCFG DT property (Hou Zhiqiang)
- Add "aer", "pme", "intr" DT properties (Li Yang)
- Add DT compatible strings for ls1028a (Xiaowei Bao)
Intel VMD host bridge driver:
- Assign VMD IRQ domain before enumeration to avoid IOMMU interrupt
remapping errors when MSI-X remapping is disabled (Nirmal Patel)
- Revert VMD workaround that kept MSI-X remapping enabled when IOMMU
remapping was enabled (Nirmal Patel)
Marvell MVEBU PCIe controller driver:
- Add of_pci_get_slot_power_limit() to parse the
'slot-power-limit-milliwatt' DT property (Pali Rohár)
- Add mvebu support for sending Set_Slot_Power_Limit message (Pali
Rohár)
MediaTek PCIe controller driver:
- Fix refcount leak in mtk_pcie_subsys_powerup() (Miaoqian Lin)
MediaTek PCIe Gen3 controller driver:
- Reset PHY and MAC at probe time (AngeloGioacchino Del Regno)
Microchip PolarFlare PCIe controller driver:
- Add chained_irq_enter()/chained_irq_exit() calls to mc_handle_msi()
and mc_handle_intx() to avoid lost interrupts (Conor Dooley)
- Fix interrupt handling race (Daire McNamara)
NVIDIA Tegra194 PCIe controller driver:
- Drop tegra194 MSI register save/restore, which is unnecessary since
the DWC core does it (Jisheng Zhang)
Qualcomm PCIe controller driver:
- Add SM8150 SoC DT binding and support (Bhupesh Sharma)
- Fix pipe clock imbalance (Johan Hovold)
- Fix runtime PM imbalance on probe errors (Johan Hovold)
- Fix PHY init imbalance on probe errors (Johan Hovold)
- Convert DT binding to YAML (Dmitry Baryshkov)
- Update DT binding to show that resets aren't required for
MSM8996/APQ8096 platforms (Dmitry Baryshkov)
- Add explicit register names per chipset in DT binding (Dmitry
Baryshkov)
- Add sc7280-specific clock and reset definitions to DT binding
(Dmitry Baryshkov)
Rockchip PCIe controller driver:
- Fix bitmap size when searching for free outbound region (Dan
Carpenter)
Rockchip DesignWare PCIe controller driver:
- Remove "snps,dw-pcie" from rockchip-dwc DT "compatible" property
because it's not fully compatible with rockchip (Peter Geis)
- Reset rockchip-dwc controller at probe (Peter Geis)
- Add rockchip-dwc INTx support (Peter Geis)
Synopsys DesignWare PCIe controller driver:
- Return error instead of success if DMA mapping of MSI area fails
(Jiantao Zhang)
Miscellaneous:
- Change pci_set_dma_mask() documentation references to
dma_set_mask() (Alex Williamson)"
* tag 'pci-v5.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (64 commits)
dt-bindings: PCI: qcom: Add schema for sc7280 chipset
dt-bindings: PCI: qcom: Specify reg-names explicitly
dt-bindings: PCI: qcom: Do not require resets on msm8996 platforms
dt-bindings: PCI: qcom: Convert to YAML
PCI: qcom: Fix unbalanced PHY init on probe errors
PCI: qcom: Fix runtime PM imbalance on probe errors
PCI: qcom: Fix pipe clock imbalance
PCI: qcom: Add SM8150 SoC support
dt-bindings: pci: qcom: Document PCIe bindings for SM8150 SoC
x86/PCI: Disable E820 reserved region clipping starting in 2023
x86/PCI: Disable E820 reserved region clipping via quirks
x86/PCI: Add kernel cmdline options to use/ignore E820 reserved regions
PCI: microchip: Fix potential race in interrupt handling
PCI/AER: Clear MULTI_ERR_COR/UNCOR_RCV bits
PCI: cadence: Clear FLR in device capabilities register
PCI: cadence: Allow PTM Responder to be enabled
PCI: vmd: Revert 2565e5b69c ("PCI: vmd: Do not disable MSI-X remapping if interrupt remapping is enabled by IOMMU.")
PCI: vmd: Assign VMD IRQ domain before enumeration
PCI: Avoid pci_dev_lock() AB/BA deadlock with sriov_numvfs_store()
PCI: rockchip-dwc: Add legacy interrupt support
...
- Assign VMD IRQ domain before enumeration to avoid IOMMU interrupt
remapping errors when MSI-X remapping is disabled (Nirmal Patel)
- Revert VMD workaround that kept MSI-X remapping enabled when IOMMU
remapping was enabled (Nirmal Patel)
* remotes/lorenzo/pci/vmd:
PCI: vmd: Revert 2565e5b69c ("PCI: vmd: Do not disable MSI-X remapping if interrupt remapping is enabled by IOMMU.")
PCI: vmd: Assign VMD IRQ domain before enumeration
- Drop unnecessary "retval" variable, since it's never read (Colin Ian
King)
* remotes/lorenzo/pci/versatile:
PCI: versatile: Remove redundant variable retval
- Fix refcount leak in mtk_pcie_subsys_powerup() (Miaoqian Lin)
- Reset PHY and MAC at probe time (AngeloGioacchino Del Regno)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek-gen3: Assert resets to ensure expected init state
PCI: mediatek: Fix refcount leak in mtk_pcie_subsys_powerup()
- Return error instead of success if DMA mapping of MSI area fails (Jiantao
Zhang)
- Drop tegra194 MSI register save/restore, which is unnecessary since the
DWC core does it (Jisheng Zhang)
- Factor out qcom enable/disable resources code (Dmitry Baryshkov)
- Remove "snps,dw-pcie" from rockchip-dwc DT "compatible" property because
it's not fully compatible with rockchip (Peter Geis)
- Reset rockchip-dwc controller at probe (Peter Geis)
- Add rockchip-dwc INTx support (Peter Geis)
* remotes/lorenzo/pci/dwc:
PCI: rockchip-dwc: Add legacy interrupt support
PCI: rockchip-dwc: Reset core at driver probe
dt-bindings: PCI: Remove fallback from Rockchip DesignWare binding
PCI: qcom-ep: Move enable/disable resources code to common functions
PCI: tegra194: Remove unnecessary MSI enable reg save and restore
PCI: dwc: Fix setting error return on MSI DMA mapping failure
Drop the leftover pm_runtime_disable() calls from the late probe error
paths that would, for example, prevent runtime PM from being reenabled
after a probe deferral.
Link: https://lore.kernel.org/r/20220401133854.10421-2-johan+linaro@kernel.org
Fixes: 6e5da6f7d8 ("PCI: qcom: Fix error handling in runtime PM support")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # 4.20
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix a clock imbalance introduced by ed8cc3b1fc ("PCI: qcom: Add support
for SDM845 PCIe controller"), which enables the pipe clock both in init()
and in post_init() but only disables in post_deinit().
Note that the pipe clock was also never disabled in the init() error
paths and that enabling the clock before powering up the PHY looks
questionable.
Link: https://lore.kernel.org/r/20220401133351.10113-1-johan+linaro@kernel.org
Fixes: ed8cc3b1fc ("PCI: qcom: Add support for SDM845 PCIe controller")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable@vger.kernel.org # 5.6
The PCIe IP (rev 1.5.0) on SM8150 SoC is similar to the one used on
SM8250. Add SM8150 support, reusing the members of ops_1_9_0.
Link: https://lore.kernel.org/r/20220326060810.1797516-3-bhupesh.sharma@linaro.org
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Clear the MSI bit in ISTATUS_LOCAL register after reading it, but
before reading and handling individual MSI bits from the ISTATUS_MSI
register. This avoids a potential race where new MSI bits may be set
on the ISTATUS_MSI register after it was read and be missed when the
MSI bit in the ISTATUS_LOCAL register is cleared.
ISTATUS_LOCAL is a read/write/clear register; the register's bits
are set when the corresponding interrupt source is activated. Each
source is independent and thus multiple sources may be active
simultaneously. The processor can monitor and clear status
bits. If one or more ISTATUS_LOCAL interrupt sources are active,
the RootPort issues an interrupt towards the processor (on
the AXI domain). Bit 28 of this register reports an MSI has been
received by the RootPort.
ISTATUS_MSI is a read/write/clear register. Bits 31-0 are asserted
when an MSI with message number 31-0 is received by the RootPort.
The processor must monitor and clear these bits.
Effectively, Bit 28 of ISTATUS_LOCAL informs the processor that
an MSI has arrived at the RootPort and ISTATUS_MSI informs the
processor which MSI (in the range 0 - 31) needs handling.
Reported by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/linux-pci/20220127202000.GA126335@bhelgaas/
Link: https://lore.kernel.org/r/20220517141622.145581-1-daire.mcnamara@microchip.com
Fixes: 6f15a9c9f9 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
-----BEGIN PGP SIGNATURE-----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=5giZ
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Avoid putting Elo i2 PCIe Ports in D3cold because downstream devices
are inaccessible after going back to D0 (Rafael J. Wysocki)
- Qualcomm SM8250 has a ddrss_sf_tbu clock but SC8180X does not; make a
SC8180X-specific config without the clock so it probes correctly
(Bjorn Andersson)
- Revert aardvark chained IRQ handler rewrite because it broke
interrupt affinity (Pali Rohár)
* tag 'pci-v5.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: aardvark: Rewrite IRQ code to chained IRQ handler"
PCI: qcom: Remove ddrss_sf_tbu clock from SC8180X
PCI/PM: Avoid putting Elo i2 PCIe Ports in D3cold
This reverts commit 1571d67dc1.
This commit broke support for setting interrupt affinity. It looks like
that it is related to the chained IRQ handler. Revert this commit until
issue with setting interrupt affinity is fixed.
Fixes: 1571d67dc1 ("PCI: aardvark: Rewrite IRQ code to chained IRQ handler")
Link: https://lore.kernel.org/r/20220515125815.30157-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[ Similarly to commit a765ed47e4 ("PCI: hv: Fix synchronization
between channel callback and hv_compose_msi_msg()"): ]
The (on-stack) teardown packet becomes invalid once the completion
timeout in hv_pci_bus_exit() has expired and hv_pci_bus_exit() has
returned. Prevent the channel callback from accessing the invalid
packet by removing the ID associated to such packet from the VMbus
requestor in hv_pci_bus_exit().
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20220511223207.3386-3-parri.andrea@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
For additional robustness in the face of Hyper-V errors or malicious
behavior, validate all values that originate from packets that Hyper-V
has sent to the guest in the host-to-guest ring buffer. Ensure that
invalid values cannot cause data being copied out of the bounds of the
source buffer in hv_pci_onchannelcallback().
While at it, remove a redundant validation in hv_pci_generic_compl():
hv_pci_onchannelcallback() already ensures that all processed incoming
packets are "at least as large as [in fact larger than] a response".
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20220511223207.3386-2-parri.andrea@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Clear FLR (Function Level Reset) from device capabilities
registers for all physical functions.
During FLR, the Margining Lane Status and Margining Lane Control
registers should not be reset, as per PCIe specification.
However, the controller incorrectly resets these registers upon FLR.
This causes PCISIG compliance FLR test to fail. Hence preventing
all functions from advertising FLR support if flag quirk_disable_flr
is set.
Link: https://lore.kernel.org/r/1635165075-89864-1-git-send-email-pthombar@cadence.com
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This enables the Controller [RP] to automatically respond with
Response/ResponseD messages if CDNS_PCIE_LM_TPM_CTRL_PTMRSEN
and PCI_PTM_CTRL_ENABLE bits are both set.
Link: https://lore.kernel.org/r/20220512055539.1782437-1-christian.gmeiner@gmail.com
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Revert 2565e5b69c ("PCI: vmd: Do not disable MSI-X remapping if
interrupt remapping is enabled by IOMMU.")
The commit 2565e5b69c was added as a workaround to keep MSI-X
remapping enabled if IOMMU enables interrupt remapping. VMD would keep
running in low performance mode. There is no dependency between MSI-X
remapping by VMD and interrupt remapping by IOMMU.
Link: https://lore.kernel.org/r/20220511095707.25403-3-nirmal.patel@linux.intel.com
Signed-off-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
During the boot process all the PCI devices are assigned default PCI-MSI
IRQ domain including VMD endpoint devices. If interrupt-remapping is
enabled by IOMMU, the PCI devices except VMD get new INTEL-IR-MSI IRQ
domain. And VMD is supposed to create and assign a separate VMD-MSI IRQ
domain for its child devices in order to support MSI-X remapping
capabilities.
Now when MSI-X remapping in VMD is disabled in order to improve
performance, VMD skips VMD-MSI IRQ domain assignment process to its
child devices. Thus the devices behind VMD get default PCI-MSI IRQ
domain instead of INTEL-IR-MSI IRQ domain when VMD creates root bus and
configures child devices.
As a result host OS fails to boot and DMAR errors were observed when
interrupt remapping was enabled on Intel Icelake CPUs. For instance:
DMAR: DRHD: handling fault status reg 2
DMAR: [INTR-REMAP] Request device [0xe2:0x00.0] fault index 0xa00 [fault reason 0x25] Blocked a compatibility format interrupt request
To fix this issue, dev_msi_info struct in dev struct maintains correct
value of IRQ domain. VMD will use this information to assign proper IRQ
domain to its child devices when it doesn't create a separate IRQ domain.
Link: https://lore.kernel.org/r/20220511095707.25403-2-nirmal.patel@linux.intel.com
Signed-off-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
According to Dexuan, the hypervisor folks beleive that multi-msi
allocations are not correct. compose_msi_msg() will allocate multi-msi
one by one. However, multi-msi is a block of related MSIs, with alignment
requirements. In order for the hypervisor to allocate properly aligned
and consecutive entries in the IOMMU Interrupt Remapping Table, there
should be a single mapping request that requests all of the multi-msi
vectors in one shot.
Dexuan suggests detecting the multi-msi case and composing a single
request related to the first MSI. Then for the other MSIs in the same
block, use the cached information. This appears to be viable, so do it.
Suggested-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1652282599-21643-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Currently if compose_msi_msg() is called multiple times, it will free any
previous IRTE allocation, and generate a new allocation. While nothing
prevents this from occurring, it is extraneous when Linux could just reuse
the existing allocation and avoid a bunch of overhead.
However, when future IRTE allocations operate on blocks of MSIs instead of
a single line, freeing the allocation will impact all of the lines. This
could cause an issue where an allocation of N MSIs occurs, then some of
the lines are retargeted, and finally the allocation is freed/reallocated.
The freeing of the allocation removes all of the configuration for the
entire block, which requires all the lines to be retargeted, which might
not happen since some lines might already be unmasked/active.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1652282582-21595-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
The legacy interrupts on the rk356x PCIe controller are handled by a
single muxed interrupt. Add IRQ domain support to the pcie-dw-rockchip
driver to support the virtual domain.
Link: https://lore.kernel.org/r/20220429123832.2376381-4-pgwipeout@gmail.com
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
The PCIe controller is in an unknown state at driver probe. This can
lead to undesireable effects when the driver attempts to configure the
controller.
Prevent issues in the future by resetting the core during probe.
Link: https://lore.kernel.org/r/20220429123832.2376381-3-pgwipeout@gmail.com
Tested-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The controller may have been left out of reset by the bootloader,
in which case, before the powerup sequence, the controller will be
found preconfigured with values that were set before booting the
kernel: this produces a controller failure, with the result of
a failure during the mtk_pcie_startup_port() sequence as the PCIe
link never gets up.
To ensure that we get a clean start in an expected state, assert
both the PHY and MAC resets before executing the controller
power-up sequence.
Link: https://lore.kernel.org/r/20220404144858.92390-1-angelogioacchino.delregno@collabora.com
Fixes: d3bf75b579 ("PCI: mediatek-gen3: Add MediaTek Gen3 driver for MT8192")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
According to the PCIe standard the PERST# signal (reset-gpio in
fsl,imx* compatible dts) should be kept asserted for at least 100 usec
before the PCIe refclock is stable, should be kept asserted for at
least 100 msec after the power rails are stable and the host should wait
at least 100 msec after it is de-asserted before accessing the
configuration space of any attached device.
From PCIe CEM r2.0, sec 2.6.2
T-PVPERL: Power stable to PERST# inactive - 100 msec
T-PERST-CLK: REFCLK stable before PERST# inactive - 100 usec.
From PCIe r5.0, sec 6.6.1
With a Downstream Port that does not support Link speeds greater than
5.0 GT/s, software must wait a minimum of 100 ms before sending a
Configuration Request to the device immediately below that Port.
Failure to do so could prevent PCIe devices to be working correctly,
and this was experienced with real devices.
Move reset assert to imx6_pcie_assert_core_reset(), this way we ensure
that PERST# is asserted before enabling any clock, move de-assert to the
end of imx6_pcie_deassert_core_reset() after the clock is enabled and
deemed stable and add a new delay of 100 msec just afterward.
Link: https://lore.kernel.org/all/20220211152550.286821-1-francesco.dolcini@toradex.com
Link: https://lore.kernel.org/r/20220404081509.94356-1-francesco.dolcini@toradex.com
Fixes: bb38919ec5 ("PCI: imx6: Add support for i.MX6 PCIe controller")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Remove code duplication by moving the code related to enabling/disabling
the resources (PHY, CLK, Reset) to common functions so that they can be
called from multiple places.
[mani: renamed the functions and reworded the commit message]
Link: https://lore.kernel.org/r/20220502104938.97033-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The Qualcomm SC8180X platform was piggy-backing on the SM8250
qcom_pcie_cfg, but SC8180X doesn't have the ddrss_sf_tbu clock, so
it now fails to probe due to the missing clock.
Give SC8180X its own qcom_pcie_cfg, without the ddrss_sf_tbu flag set.
Fixes: 0614f98bbb ("PCI: qcom: Add ddrss_sf_tbu flag")
Link: https://lore.kernel.org/r/20220331013415.592748-1-bjorn.andersson@linaro.org
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Currently when the pci-hyperv driver finishes probing and initializing the
PCI device, it sets the PCI_COMMAND_MEMORY bit; later when the PCI device
is registered to the core PCI subsystem, the core PCI driver's BAR detection
and initialization code toggles the bit multiple times, and each toggling of
the bit causes the hypervisor to unmap/map the virtual BARs from/to the
physical BARs, which can be slow if the BAR sizes are huge, e.g., a Linux VM
with 14 GPU devices has to spend more than 3 minutes on BAR detection and
initialization, causing a long boot time.
Reduce the boot time by not setting the PCI_COMMAND_MEMORY bit when we
register the PCI device (there is no need to have it set in the first place).
The bit stays off till the PCI device driver calls pci_enable_device().
With this change, the boot time of such a 14-GPU VM is reduced by almost
3 minutes.
Link: https://lore.kernel.org/lkml/20220419220007.26550-1-decui@microsoft.com/
Tested-by: Boqun Feng (Microsoft) <boqun.feng@gmail.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jake Oshins <jakeo@microsoft.com>
Link: https://lore.kernel.org/r/20220502074255.16901-1-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
In the multi-MSI case, hv_arch_irq_unmask() will only operate on the first
MSI of the N allocated. This is because only the first msi_desc is cached
and it is shared by all the MSIs of the multi-MSI block. This means that
hv_arch_irq_unmask() gets the correct address, but the wrong data (always
0).
This can break MSIs.
Lets assume MSI0 is vector 34 on CPU0, and MSI1 is vector 33 on CPU0.
hv_arch_irq_unmask() is called on MSI0. It uses a hypercall to configure
the MSI address and data (0) to vector 34 of CPU0. This is correct. Then
hv_arch_irq_unmask is called on MSI1. It uses another hypercall to
configure the MSI address and data (0) to vector 33 of CPU0. This is
wrong, and results in both MSI0 and MSI1 being routed to vector 33. Linux
will observe extra instances of MSI1 and no instances of MSI0 despite the
endpoint device behaving correctly.
For the multi-MSI case, we need unique address and data info for each MSI,
but the cached msi_desc does not provide that. However, that information
can be gotten from the int_desc cached in the chip_data by
compose_msi_msg(). Fix the multi-MSI case to use that cached information
instead. Since hv_set_msi_entry_from_desc() is no longer applicable,
remove it.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1651068453-29588-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Variable retval is being assigned a value that is never read, the
variable is redundant and can be removed.
Cleans up clang scan build warning:
drivers/pci/controller/pci-versatile.c:37:10: warning: Although the value
stored to 'retval' is used in the enclosing expression, the value is never
actually read from 'retval' [deadcode.DeadStores]
Link: https://lore.kernel.org/r/20220418144416.86121-1-colin.i.king@gmail.com
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Dexuan wrote:
"[...] when we disable AccelNet, the host PCI VSP driver sends a
PCI_EJECT message first, and the channel callback may set
hpdev->state to hv_pcichild_ejecting on a different CPU. This can
cause hv_compose_msi_msg() to exit from the loop and 'return', and
the on-stack variable 'ctxt' is invalid. Now, if the response
message from the host arrives, the channel callback will try to
access the invalid 'ctxt' variable, and this may cause a crash."
Schematically:
Hyper-V sends PCI_EJECT msg
hv_pci_onchannelcallback()
state = hv_pcichild_ejecting
hv_compose_msi_msg()
alloc and init comp_pkt
state == hv_pcichild_ejecting
Hyper-V sends VM_PKT_COMP msg
hv_pci_onchannelcallback()
retrieve address of comp_pkt
'free' comp_pkt and return
comp_pkt->completion_func()
Dexuan also showed how the crash can be triggered after introducing
suitable delays in the driver code, thus validating the 'assumption'
that the host can still normally respond to the guest's compose_msi
request after the host has started to eject the PCI device.
Fix the synchronization by leveraging the requestor lock as follows:
- Before 'return'-ing in hv_compose_msi_msg(), remove the ID (while
holding the requestor lock) associated to the completion packet.
- Retrieve the address *and call ->completion_func() within a same
(requestor) critical section in hv_pci_onchannelcallback().
Reported-by: Wei Hu <weh@microsoft.com>
Reported-by: Dexuan Cui <decui@microsoft.com>
Suggested-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20220419122325.10078-7-parri.andrea@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Currently, pointers to guest memory are passed to Hyper-V as transaction
IDs in hv_pci. In the face of errors or malicious behavior in Hyper-V,
hv_pci should not expose or trust the transaction IDs returned by
Hyper-V to be valid guest memory addresses. Instead, use small integers
generated by vmbus_requestor as request (transaction) IDs.
Suggested-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20220419122325.10078-3-parri.andrea@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
If the allocation of multiple MSI vectors for multi-MSI fails in the core
PCI framework, the framework will retry the allocation as a single MSI
vector, assuming that meets the min_vecs specified by the requesting
driver.
Hyper-V advertises that multi-MSI is supported, but reuses the VECTOR
domain to implement that for x86. The VECTOR domain does not support
multi-MSI, so the alloc will always fail and fallback to a single MSI
allocation.
In short, Hyper-V advertises a capability it does not implement.
Hyper-V can support multi-MSI because it coordinates with the hypervisor
to map the MSIs in the IOMMU's interrupt remapper, which is something the
VECTOR domain does not have. Therefore the fix is simple - copy what the
x86 IOMMU drivers (AMD/Intel-IR) do by removing
X86_IRQ_ALLOC_CONTIGUOUS_VECTORS after calling the VECTOR domain's
pci_msi_prepare().
Fixes: 4daace0d8c ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/1649856981-14649-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
If the driver is configured as a module (after allowing this by changing
PCIE_MICROCHIP_HOST from bool to tristate) the missing semicolon makes the
compiler very unhappy. While there isn't a real problem as
MODULE_DEVICE_TABLE always evaluates to nothing for a built-in driver,
do it right for consistency with other drivers.
Link: https://lore.kernel.org/r/20220420065832.14173-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Daire McNamara <daire.mcnamara@microchip.com>
If DT supplies the 'slot-power-limit-milliwatt' property, program
the value in the Slot Power Limit in the Slot Capabilities register
and program the Root Port to send a Set_Slot_Power_Limit Message
when the Link transitions to DL_Up.
Link: https://lore.kernel.org/r/20220412094946.27069-5-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The integrated MSI Receiver enable register is always initialized in
dw_pcie_setup_rc() which is also called in resume code path, so we
don't need to save/restore the enable register during suspend/resume.
Link: https://lore.kernel.org/r/20211226074910.2722-1-jszhang@kernel.org
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
When dma_mapping_error() returns error because of no enough memory,
but dw_pcie_host_init() returns success, which will mislead the callers.
Link: https://lore.kernel.org/r/30170911-0e2f-98ce-9266-70465b9073e5@huawei.com
Fixes: 07940c369a ("PCI: dwc: Fix MSI page leakage in suspend/resume")
Signed-off-by: Jianrong Zhang <zhangjianrong5@huawei.com>
Signed-off-by: Jiantao Zhang <water.zhangjiantao@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Link: https://lore.kernel.org/r/20220309091953.5630-1-linmq006@gmail.com
Fixes: 87e8657ba9 ("PCI: mediatek: Add new method to get shared pcie-cfg base address")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
The ep->ob_region_map bitmap is a long and it has BITS_PER_LONG bits.
Link: https://lore.kernel.org/r/20220315065944.GB13572@kili
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The ep->ob_region_map bitmap is a long and it has BITS_PER_LONG bits.
Link: https://lore.kernel.org/r/20220315065829.GA13572@kili
Fixes: 37dddf14f1 ("PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fix the following build error:
drivers/pci/controller/pci-hyperv.c:769:13: error: ‘hv_set_msi_entry_from_desc’ defined but not used [-Werror=unused-function]
769 | static void hv_set_msi_entry_from_desc(union hv_msi_entry *msi_entry,
The arm64 implementation of hv_set_msi_entry_from_desc() is not used after
d06957d7a6 ("PCI: hv: Avoid the retarget interrupt hypercall in
irq_unmask() on ARM64"), so remove it.
Fixes: d06957d7a6 ("PCI: hv: Avoid the retarget interrupt hypercall in irq_unmask() on ARM64")
Link: https://lore.kernel.org/r/20220317085130.36388-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Boqun Feng <boqun.feng@gmail.com>
PCI pass-thru devices in a Hyper-V VM are represented as a VMBus
device and as a PCI device. The coherence of the VMbus device is
set based on the VMbus node in ACPI, but the PCI device has no
ACPI node and defaults to not hardware coherent. This results
in extra software coherence management overhead on ARM64 when
devices are hardware coherent.
Fix this by setting up the PCI host bus so that normal
PCI mechanisms will propagate the coherence of the VMbus
device to the PCI device. There's no effect on x86/x64 where
devices are always hardware coherent.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Boqun Feng <boqun.feng@gmail.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/1648138492-2191-3-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
There will be two merge conflicts with your tree, one in MAINTAINERS
which is obvious to fix up, and one in drivers/phy/freescale/Kconfig
which also should be easy to resolve.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG3fQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNEgCfaRG8CRxewDXOO4+GSeA3NGK+AIoAnR89donC
R4bgCjfg8BWIBcVVXg3/
=WWXC
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmI7iOwUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vxkuhAAtJkVwfeyUjZ8sms+qWdZaucJmFF1
PDeKy8O8upLzRRykdWoAOjKKVcCB9ohxBjPMco2oYNTmSozxeau8jjMA9OTQvTOS
ZhDDoi49/vHRHuq3WIeAMCuk7tH3H1L3f0UHJxJ3H/oObQ+eMsitPcGFK+QrISDX
pYokOnXZvf7BT7NpVtogSe2mhniOD1zQSicAMiH6WKNHHZcxewrzV9LP3MFOoBAr
VMhlhzJbOp9spvCt7M1DycJEQ2RNe+wGLBFDalhPuprwnkNchRV+0AwWfD90zc9u
h/0J8jkXfqS6QfSd/lOlTvI6kGsV8UKZEt4h4X/hlHFebFM5ktD9X7GmcoYUDFd9
aHV3I/Jf62uGJ31IrT0V/cSYNlMO+IVFwXLGir4B1cFPOkzyIG/i60iV/C6bnnCa
TCMH6vxalFycYaHBFqw/K/Dlq+mrAX74nQDfbk8y6rprczM1BN220Z8BkpG13TBu
MxgCEul2/BJmNcPS1IWb/mCfBy+rdrVn2DZuID3J9KTwKNOUTIuAF0FuxLP4Bk4o
sti3vKIXOcHnAcJB9tEnpEfstPv2JT13eWDIMmp/qCwqcujOvsg/DSYrx+8ogmBF
DJ/sbPy3BdIOAeTgepWHAxYcv9SlZTGJGl+oaR1zV0qLBogyQUWZ9Ijx5aAEAw3j
AJicpdk3BkH3LC8=
=5Q9H
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Move the VGA arbiter from drivers/gpu to drivers/pci because it's
PCI-specific, not GPU-specific (Bjorn Helgaas)
- Select the default VGA device consistently whether it's enumerated
before or after VGA arbiter init, which fixes arches that enumerate
PCI devices late (Huacai Chen)
Resource management:
- Support BAR sizes up to 8TB (Dongdong Liu)
PCIe native device hotplug:
- Fix "Command Completed" tracking to avoid spurious timouts when
powering off empty slots (Liguang Zhang)
- Quirk Qualcomm devices that don't implement Command Completed
correctly, again to avoid spurious timeouts (Manivannan Sadhasivam)
Peer-to-peer DMA:
- Add Intel 3rd Gen Intel Xeon Scalable Processors to whitelist
(Michael J. Ruhl)
APM X-Gene PCIe controller driver:
- Revert generic DT parsing changes that broke some machines in the
field (Marc Zyngier)
Freescale i.MX6 PCIe controller driver:
- Allow controller probe to succeed even when no devices currently
present to allow hot-add later (Fabio Estevam)
- Enable power management on i.MX6QP (Richard Zhu)
- Assert CLKREQ# on i.MX8MM so enumeration doesn't hang when no
device is connected (Richard Zhu)
Marvell Aardvark PCIe controller driver:
- Fix MSI and MSI-X support (Marek Behún, Pali Rohár)
- Add support for ERR and PME interrupts (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Add DT binding and support for "num-lanes" (Pali Rohár)
- Add support for INTx interrupts (Pali Rohár)
Microsoft Hyper-V host bridge driver:
- Avoid unnecessary hypercalls when unmasking IRQs on ARM64 (Boqun
Feng)
Qualcomm PCIe controller driver:
- Add SM8450 DT binding and driver support (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Help the controller get to the L1 state since the hardware can't do
it on its own (Marek Vasut)
- Return PCI_ERROR_RESPONSE (~0) for reads that fail on PCIe (Marek
Vasut)
SiFive FU740 PCIe controller driver:
- Drop redundant '-gpios' from DT GPIO lookup (Ben Dooks)
- Force 2.5GT/s for initial device probe (Ben Dooks)
Socionext UniPhier Pro5 controller driver:
- Add NX1 DT binding and driver support (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Restore MSI configuration so MSI works after resume (Jisheng
Zhang)"
* tag 'pci-v5.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (94 commits)
x86/PCI: Add #includes to asm/pci_x86.h
PCI: ibmphp: Remove unused assignments
PCI: cpqphp: Remove unused assignments
PCI: fu740: Remove unused assignments
PCI: kirin: Remove unused assignments
PCI: Remove unused assignments
PCI: Declare pci_filp_private only when HAVE_PCI_MMAP
PCI: Avoid broken MSI on SB600 USB devices
PCI: fu740: Force 2.5GT/s for initial device probe
PCI: xgene: Revert "PCI: xgene: Fix IB window setup"
PCI: xgene: Revert "PCI: xgene: Use inbound resources for setup"
PCI: imx6: Assert i.MX8MM CLKREQ# even if no device present
PCI: imx6: Invoke the PHY exit function after PHY power off
PCI: rcar: Use PCI_SET_ERROR_RESPONSE after read which triggered an exception
PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()
PCI: dwc: Restore MSI Receiver mask during resume
PCI: fu740: Drop redundant '-gpios' from DT GPIO lookup
PCI/VGA: Replace full MIT license text with SPDX identifier
PCI/VGA: Use unsigned format string to print lock counts
PCI/VGA: Log bridge control messages when adding devices
...
- Finish transition to L1 state in rcar_pcie_config_access() because R-Car
can't do it on its own (Marek Vasut)
- Return PCI_ERROR_RESPONSE for reads that trigger PCIe errors (Marek
Vasut)
* remotes/lorenzo/pci/rcar:
PCI: rcar: Use PCI_SET_ERROR_RESPONSE after read which triggered an exception
PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()
- Save pointer to device match data instead of copying it (Dmitry
Baryshkov)
- Add ddrss_sf_tbu flag to device match data instead of checking OF
compatible string (Dmitry Baryshkov)
- Add SM8450 SoC PCIe DT bindings (Dmitry Baryshkov)
- Add SM8450 PCIe support (Dmitry Baryshkov)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Add SM8450 PCIe support
PCI: qcom: Add ddrss_sf_tbu flag
PCI: qcom: Remove redundancy between qcom_pcie and qcom_pcie_cfg
dt-bindings: pci: qcom: Document PCIe bindings for SM8450
- Add Pali Rohár as pci-mvebu.c maintainer (Pali Rohár)
- Make struct pci_bridge_emul_ops const (Pali Rohár)
- Rename PCI_BRIDGE_EMUL_NO_PREFETCHABLE_BAR to
PCI_BRIDGE_EMUL_NO_PREFMEM_FORWARD since it doesn't apply to BARs (Pali
Rohár)
- Add new flag PCI_BRIDGE_EMUL_NO_IO_FORWARD for bridges that don't support
IO forwarding (Pali Rohár)
- Add Kconfig help text for CONFIG_PCI_MVEBU (Pali Rohár)
- Remove duplicate nports assignment (Pali Rohár)
- Set PCI_BRIDGE_EMUL_NO_IO_FORWARD when IO is unsupported (Pali Rohár)
- Initialize vendor, device and revision of emulated bridge (Pali Rohár)
- Fix Data Link Layer Link Active reporting on emulated bridge (Pali Rohár)
- Rearrange tests in bridge emulation for easier maintenance (Russell King)
- Add emulated bridge support for PCIe extended capabilities (Russell King)
- Add emulated bridge support for bridge Subsystem Vendor ID capability
(Pali Rohár)
- Configure Maximum Link Width based on DT "num-lanes" property (Pali
Rohár)
- Emulate bridge Subsystem Vendor ID capability (Pali Rohár)
- Emulate AER Capability (Pali Rohár)
- Use PCI core bridge->ops and bridge->child_ops to separate config
accesses to Root Port vs downstream devices (Pali Rohár)
- Unmask all INTx interrupts; they're reported via a single shared GIC
source (Pali Rohár)
- Add INTx support (Pali Rohár)
* remotes/lorenzo/pci/mvebu:
PCI: mvebu: Implement support for legacy INTx interrupts
PCI: mvebu: Fix macro names and comments about legacy interrupts
dt-bindings: PCI: mvebu: Update information about intx interrupts
PCI: mvebu: Use child_ops API
PCI: mvebu: Add support for Advanced Error Reporting registers on emulated bridge
PCI: mvebu: Add support for PCI Bridge Subsystem Vendor ID on emulated bridge
PCI: mvebu: Correctly configure x1/x4 mode
dt-bindings: PCI: mvebu: Add num-lanes property
PCI: pci-bridge-emul: Add support for PCI Bridge Subsystem Vendor ID capability
PCI: pci-bridge-emul: Add support for PCIe extended capabilities
PCI: pci-bridge-emul: Re-arrange register tests
PCI: mvebu: Fix reporting Data Link Layer Link Active on emulated bridge
PCI: mvebu: Update comment for PCI_EXP_LNKCTL register on emulated bridge
PCI: mvebu: Update comment for PCI_EXP_LNKCAP register on emulated bridge
PCI: mvebu: Properly initialize vendor, device and revision of emulated bridge
PCI: mvebu: Set PCI_BRIDGE_EMUL_NO_IO_FORWARD when IO is unsupported
PCI: mvebu: Remove duplicate nports assignment
PCI: mvebu: Add help string for CONFIG_PCI_MVEBU option
PCI: pci-bridge-emul: Add support for new flag PCI_BRIDGE_EMUL_NO_IO_FORWARD
PCI: pci-bridge-emul: Rename PCI_BRIDGE_EMUL_NO_PREFETCHABLE_BAR to PCI_BRIDGE_EMUL_NO_PREFMEM_FORWARD
PCI: pci-bridge-emul: Make struct pci_bridge_emul_ops as const
MAINTAINERS: Add Pali Rohár as pci-mvebu.c maintainer
- Allow host controller driver to probe successfully (as other drivers do)
even if link is currently down (Fabio Estevam)
- Enable i.MX6QP PCIe power management (Richard Zhu)
- Invoke PHY exit function after PHY power off (Richard Zhu)
- Assert i.MX8MM CLKREQ# even if no device present to avoid boot hangs
(Richard Zhu)
* remotes/lorenzo/pci/imx6:
PCI: imx6: Assert i.MX8MM CLKREQ# even if no device present
PCI: imx6: Invoke the PHY exit function after PHY power off
PCI: imx6: Enable i.MX6QP PCIe power management support
PCI: imx6: Allow to probe when dw_pcie_wait_for_link() fails
- Avoid retarget interrupt hypercall in irq_unmask() on ARM64 (Boqun Feng)
* remotes/lorenzo/pci/hv:
PCI: hv: Avoid the retarget interrupt hypercall in irq_unmask() on ARM64
- Drop redundant '-gpios' from DT GPIO lookup (Ben Dooks)
- Force 2.5GT/s for initial device probe to workaround enumeration issue on
SiFive Unmatched board (Ben Dooks)
* pci/host/fu740:
PCI: fu740: Force 2.5GT/s for initial device probe
PCI: fu740: Drop redundant '-gpios' from DT GPIO lookup
- Use PCI_INTERRUPT_* definitions from PCI core instead of custom ones
(Pali Rohár)
- Derive MSI number from bit(s) set in PCIE_MSI_STATUS_REG, not from
PCIE_MSI_PAYLOAD_REG (Pali Rohár)
- Align multi-MSI vectors to power of two (Pali Rohár)
- Rewrite IRQ code to use chained IRQ handler (Pali Rohár)
- Check return value of generic_handle_domain_irq() and warn about spurious
interrupts (Pali Rohár)
- Make MSI irq_chip structures static to driver (Marek Behún)
- Make msi_domain_info structure static to driver (Marek Behún)
- Use dev_fwnode() instead of of_node_to_fwnode(dev->of_node) (Marek Behún)
- Refactor unmasking of summary MSI interrupt (Pali Rohár)
- Add support for masking MSI interrupts and leave them masked at setup
(Pali Rohár)
- Set MSI doorbell address to address of struct advk_pcie (Pali Rohár)
- Enable MSI-X support (Pali Rohár)
- Add support for ERR interrupt on emulated bridge (Pali Rohár)
- Fix read of PCI_EXP_RTSTA_PME bit on emulated bridge (Pali Rohár)
- Optimize writing PCI_EXP_RTCTL_PMEIE and PCI_EXP_RTSTA_PME on emulated
bridge (Pali Rohár)
- Add support for PME interrupts (Pali Rohár)
- Fix support for PME requester on emulated bridge (Pali Rohár)
- Use separate INTA interrupt for emulated Root Port so PME and AER
interrupt is not shared with downstream devices (Pali Rohár)
- Remove irq_mask_ack() callback for INTx interrupts (Pali Rohár)
- Don't mask legacy INTx interrupts when mapping (Pali Rohár)
- Drop unnecessary "__maybe_unused" from advk_pcie_disable_phy() (Marek
Behún)
- Update comment about why we check for link being up before issuing a
config request (Marek Behún)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Update comment about link going down after link-up
PCI: aardvark: Drop __maybe_unused from advk_pcie_disable_phy()
PCI: aardvark: Don't mask irq when mapping
PCI: aardvark: Remove irq_mask_ack() callback for INTx interrupts
PCI: aardvark: Use separate INTA interrupt for emulated root bridge
PCI: aardvark: Fix support for PME requester on emulated bridge
PCI: aardvark: Add support for PME interrupts
PCI: aardvark: Optimize writing PCI_EXP_RTCTL_PMEIE and PCI_EXP_RTSTA_PME on emulated bridge
PCI: aardvark: Fix reading PCI_EXP_RTSTA_PME bit on emulated bridge
PCI: aardvark: Add support for ERR interrupt on emulated bridge
PCI: aardvark: Enable MSI-X support
PCI: aardvark: Fix setting MSI address
PCI: aardvark: Add support for masking MSI interrupts
PCI: aardvark: Refactor unmasking summary MSI interrupt
PCI: aardvark: Use dev_fwnode() instead of of_node_to_fwnode(dev->of_node)
PCI: aardvark: Make msi_domain_info structure a static driver structure
PCI: aardvark: Make MSI irq_chip structures static driver structures
PCI: aardvark: Check return value of generic_handle_domain_irq() when processing INTx IRQ
PCI: aardvark: Rewrite IRQ code to chained IRQ handler
PCI: aardvark: Fix support for MSI interrupts
PCI: aardvark: Fix reading MSI interrupt number
PCI: aardvark: Replace custom PCIE_CORE_INT_* macros with PCI_INTERRUPT_*
fu740_pcie_host_init() assigned "ret", but never used the value. Drop it.
Found by Krzysztof using cppcheck:
$ cppcheck --enable=all --force
unreadVariable drivers/pci/controller/dwc/pcie-fu740.c:227 Variable 'ret' is assigned a value that is never used.
Reported-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20220313192933.434746-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
hi3660_pcie_phy_init() assigned "pdev", but never used the value. Drop it.
Found by Krzysztof using cppcheck:
$ cppcheck --enable=all --force
unreadVariable drivers/pci/controller/dwc/pcie-kirin.c:336 Variable 'pdev' is assigned a value that is never used.
Reported-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20220313192933.434746-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The fu740 PCIe core does not probe any devices on the SiFive Unmatched
board without this fix (or having U-Boot explicitly start the PCIe via
either boot-script or user command). The fix is to start the link at
2.5GT/s speeds and once the link is up then change the maximum speed back
to the default.
The U-Boot driver claims to set the link-speed to 2.5GT/s to get the probe
to work (and U-Boot does print link up at 2.5GT/s) in the following code:
https://source.denx.de/u-boot/u-boot/-/blob/master/drivers/pci/pcie_dw_sifive.c?id=v2022.01#L271
Link: https://lore.kernel.org/r/20220318152430.526320-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Commit c7a75d0782 ("PCI: xgene: Fix IB window setup") tried to
fix the damages that 6dce5aa59e ("PCI: xgene: Use inbound resources
for setup") caused, but actually didn't improve anything for some
plarforms (at least Mustang and m400 are still broken).
Given that 6dce5aa59e has been reverted, revert this patch as well,
restoring the PCIe support on XGene to its pre-5.5, working state.
Link: https://lore.kernel.org/r/YjN8pT5e6/8cRohQ@xps13.dannf
Link: https://lore.kernel.org/r/20220321104843.949645-3-maz@kernel.org
Fixes: c7a75d0782 ("PCI: xgene: Fix IB window setup")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Stéphane Graber <stgraber@ubuntu.com>
Cc: dann frazier <dann.frazier@canonical.com>
Commit 6dce5aa59e ("PCI: xgene: Use inbound resources for setup")
killed PCIe on my XGene-1 box (a Mustang board). The machine itself
is still alive, but half of its storage (over NVMe) is gone, and the
NVMe driver just times out.
Note that this machine boots with a device tree provided by the
UEFI firmware (2016 vintage), which could well be non conformant
with the spec, hence the breakage.
With the patch reverted, the box boots 5.17-rc8 with flying colors.
Link: https://lore.kernel.org/all/Yf2wTLjmcRj+AbDv@xps13.dannf
Link: https://lore.kernel.org/r/20220321104843.949645-2-maz@kernel.org
Fixes: 6dce5aa59e ("PCI: xgene: Use inbound resources for setup")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Stéphane Graber <stgraber@ubuntu.com>
Cc: dann frazier <dann.frazier@canonical.com>
The CLKREQ# signal is an open drain, active low signal that is driven
low by the remote Endpoint device. But it might not be driven low if no
Endpoint device is connected.
On i.MX8MM PCIe, phy_init() may fail and system boot may hang if no
Endpoint is connected to assert CLKREQ#.
Handle this as on i.MX8MQ, where we explicitly assert CLKREQ# so the
PHY can be initialized.
Link: https://lore.kernel.org/r/1645672013-8949-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 178e244cb6 ("PCI: imx: Add the imx8mm pcie support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
To balance phy->init_count, invoke the phy_exit() after phy_power_off().
Link: https://lore.kernel.org/r/1646289275-17813-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 178e244cb6 ("PCI: imx: Add the imx8mm pcie support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
In case the controller is transitioning to L1 in rcar_pcie_config_access(),
any read/write access to PCIECDR triggers asynchronous external abort. This
is because the transition to L1 link state must be manually finished by the
driver. The PCIe IP can transition back from L1 state to L0 on its own.
The current asynchronous external abort hook implementation restarts
the instruction which finally triggered the fault, which can be a
different instruction than the read/write instruction which started
the faulting access. Usually the instruction which finally triggers
the fault is one which has some data dependency on the result of the
read/write. In case of read, the read value after fixup is undefined,
while a read value of faulting read should be PCI_ERROR_RESPONSE.
It is possible to enforce the fault using 'isb' instruction placed
right after the read/write instruction which started the faulting
access. Add custom register accessors which perform the read/write
followed immediately by 'isb'.
This way, the fault always happens on the 'isb' and in case of read,
which is located one instruction before the 'isb', it is now possible
to fix up the return value of the read in the asynchronous external
abort hook and make that read return PCI_ERROR_RESPONSE.
Link: https://lore.kernel.org/r/20220312212349.781799-2-marek.vasut@gmail.com
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
In case the controller is transitioning to L1 in rcar_pcie_config_access(),
any read/write access to PCIECDR triggers asynchronous external abort. This
is because the transition to L1 link state must be manually finished by the
driver. The PCIe IP can transition back from L1 state to L0 on its own.
Avoid triggering the abort in rcar_pcie_config_access() by checking whether
the controller is in the transition state, and if so, finish the transition
right away. This prevents a lot of unnecessary exceptions, although not all
of them.
Link: https://lore.kernel.org/r/20220312212349.781799-1-marek.vasut@gmail.com
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
- Add support for the STM32MP13 variant
- Move parent device away from struct irq_chip
- Remove all instances of non-const strings assigned to
struct irq_chip::name, enabling a nice cleanup for VIC and GIC)
- Simplify the Qualcomm PDC driver
- A bunch of SiFive PLIC cleanups
- Add support for a new variant of the Meson GPIO block
- Add support for the irqchip side of the Apple M1 PMU
- Add support for the Apple M1 Pro/Max AICv2 irqchip
- Add support for the Qualcomm MPM wakeup gadget
- Move the Xilinx driver over to the generic irqdomain handling
- Tiny speedup for IPIs on GICv3 systems
- The usual odd cleanups
-----BEGIN PGP SIGNATURE-----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=cf1B
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- Add support for the STM32MP13 variant
- Move parent device away from struct irq_chip
- Remove all instances of non-const strings assigned to
struct irq_chip::name, enabling a nice cleanup for VIC and GIC)
- Simplify the Qualcomm PDC driver
- A bunch of SiFive PLIC cleanups
- Add support for a new variant of the Meson GPIO block
- Add support for the irqchip side of the Apple M1 PMU
- Add support for the Apple M1 Pro/Max AICv2 irqchip
- Add support for the Qualcomm MPM wakeup gadget
- Move the Xilinx driver over to the generic irqdomain handling
- Tiny speedup for IPIs on GICv3 systems
- The usual odd cleanups
Link: https://lore.kernel.org/all/20220313105142.704579-1-maz@kernel.org
- New support:
- Mediatek tphy support for MT8186
- Qualcomm usb phy support for sc8180x and sc8280xp
- Qualcomm ufs phy support for sc8180x and sc8280xp
- Qualcomm usb phy support for MSM8953
- Cadence D-Phy Rx support
- Sun4i support for USB phy
- Rockchip naneng combo phy support for RK3568
- Qualcomm eDP PHY for sc7280
- Updates:
- wake on support for Synopsis XHCI controllers
- Yamilify Qualcomm USB HS phy binding
- Charger detection support for TI tusb1210
-----BEGIN PGP SIGNATURE-----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=8baK
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-next
Vinod writes:
phy-for-5.18
- New support:
- Mediatek tphy support for MT8186
- Qualcomm usb phy support for sc8180x and sc8280xp
- Qualcomm ufs phy support for sc8180x and sc8280xp
- Qualcomm usb phy support for MSM8953
- Cadence D-Phy Rx support
- Sun4i support for USB phy
- Rockchip naneng combo phy support for RK3568
- Qualcomm eDP PHY for sc7280
- Updates:
- wake on support for Synopsis XHCI controllers
- Yamilify Qualcomm USB HS phy binding
- Charger detection support for TI tusb1210
* tag 'phy-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (53 commits)
phy: qcom-qmp: add sc8280xp UFS PHY
dt-bindings: phy: qcom,qmp: add sc8180x and sc8280xp ufs compatibles
phy: qcom-snps: Add sc8280xp support
dt-bindings: phy: qcom,usb-snps-femto-v2: Add sc8180x and sc8280xp
dt-bindings: Revert "dt-bindings: soc: grf: add naneng combo phy register compatible"
phy: dt-bindings: Add Cadence D-PHY Rx bindings
phy: dt-bindings: cdns,dphy: add power-domains property
phy: dt-bindings: Convert Cadence DPHY binding to YAML
phy: cadence: Add Cadence D-PHY Rx driver
dt-bindings: phy: renesas,usb2-phy: Document RZ/V2L phy bindings
Revert "PCI: aardvark: Fix initialization with old Marvell's Arm Trusted Firmware"
Revert "usb: host: xhci: mvebu: make USB 3.0 PHY optional for Armada 3720"
Revert "ata: ahci: mvebu: Make SATA PHY optional for Armada 3720"
phy: marvell: phy-mvebu-a3700-comphy: Add native kernel implementation
phy: marvell: phy-mvebu-a3700-comphy: Remove port from driver configuration
phy: phy-brcm-usb: fixup BCM4908 support
dt-bindings: phy: mediatek,tphy: Add compatible for MT8192
phy: ti: tusb1210: Add charger detection
phy: ti: tusb1210: Add a delay between power-on and restoring the phy-parameters
phy: ti: tusb1210: Drop tusb->vendor_specific2 != 0 check from tusb1210_power_on()
...
If a host that uses the IP's integrated MSI Receiver lost power
during suspend, we call dw_pcie_setup_rc() to reinit the RC. But
dw_pcie_setup_rc() always sets pp->irq_mask[ctrl] to ~0, so the mask
register is always set as 0xffffffff incorrectly, thus the MSI can't
work after resume.
Fix this issue by moving pp->irq_mask[ctrl] initialization to
dw_pcie_host_init() so we can correctly set the mask reg during both
boot and resume.
Tested-by: Richard Zhu <hongxing.zhu@nxp.com>
Link: https://lore.kernel.org/r/20211226074019.2556-1-jszhang@kernel.org
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The calls to devm_gpiod_get_optional() have the -gpios at the end of the
name but the GPIO core code is already adding the suffix during the lookup.
This means the PCIe driver is not finding the necessary reset or power
lines to allow initialisation of the PCIe.
Drop the redundant '-gpios' when we look up GPIOs from the DT.
This bug has not been noticed because if U-Boot has setup the GPIO lines
for the hardware when it does the PCIe initialisation (either by booting
from PCIe or user command to access PCIe) then the PCIe will work in Linux.
The U-Boot as supplied by SiFive does not by default initialise any PCIe
component.
Link: https://lore.kernel.org/r/20220221210347.1335004-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
AIC2 changes the IRQ fwspec to add a cell. Always use the second-to-last
cell for the MSI handling, so it will work for both AIC1 and AIC2 devices.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220309192123.152028-2-marcan@marcan.st
i.MX6QP PCIe supports the reset logic, thus it can reset itself to the
initialized state when exit from L2 or L3 states.
Enable the i.MX6QP PCIe suspend/resume operations support.
Link: https://lore.kernel.org/r/1645425237-4071-2-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
On ARM64 Hyper-V guests, SPIs are used for the interrupts of virtual PCI
devices, and SPIs can be managed directly via GICD registers. Therefore
the retarget interrupt hypercall is not needed on ARM64.
An arch-specific interface hv_arch_irq_unmask() is introduced to handle
the architecture level differences on this. For x86, the behavior
remains unchanged, while for ARM64 no hypercall is invoked when
unmasking an irq for virtual PCI devices.
Link: https://lore.kernel.org/r/20220217034525.1687678-1-boqun.feng@gmail.com
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
resulted in a recursive locking problem in the VMD driver. The cure is to
cache the relevant information upfront instead of retrieving it at runtime.
-----BEGIN PGP SIGNATURE-----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=ukul
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2022-02-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single fix for a regression caused by the recent PCI/MSI rework
which resulted in a recursive locking problem in the VMD driver.
The cure is to cache the relevant information upfront instead of
retrieving it at runtime"
* tag 'irq-urgent-2022-02-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
PCI: vmd: Prevent recursive locking on interrupt allocation
