This patch add support for the writing and reading of the phy registers.
LAN937x uses the Vphy indirect addressing method for accessing the phys.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch update the ksz_get_tag_protocol to return LAN937x specific
tag if the chip id matches one of LAN937x series switch
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic DSA driver support for lan937x and the device will be
configured through SPI interface.
It adds the lan937x_dev_ops in ksz_common.c file and tries to reuse the
functionality of ksz9477 series switch.
drivers/net/dsa/microchip/ path is already part of MAINTAINERS &
the new files come under this path. Hence no update needed to the
MAINTAINERS
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz9477 and lan937x has few difference in the static and reserved
table register 0x041C. For the ksz9477 if the bit 0 is 1 - read
operation and 0 - write operation. But for lan937x bit 1:0 used for
selecting the read/write operation, 01 - write and 10 - read.
To use ksz9477 mdb add/del and enable_stp_addr for the lan937x, masks &
shifts are introduced for ksz9477 & lan937x in ksz_common.c. Then
updated the function with masks & shifts based on the switch instead of
hard coding it.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Time-sensitive networking code needs to work with PTP times expressed in
nanoseconds, and with packet transmission times expressed in
picoseconds, since those would be fractional at higher than gigabit
speed when expressed in nanoseconds.
Convert the existing uses in tc-taprio and the ocelot/felix DSA driver
to a PSEC_PER_NSEC macro. This macro is placed in include/linux/time64.h
as opposed to its relatives (PSEC_PER_SEC etc) from include/vdso/time64.h
because the vDSO library does not (yet) need/use it.
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> # for the vDSO parts
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, sending a packet into a time gate too small for it (or always
closed) causes the queue system to hold the frame forever. Even worse,
this frame isn't subject to aging either, because for that to happen, it
needs to be scheduled for transmission in the first place. But the frame
will consume buffer memory and frame references while it is forever held
in the queue system.
Before commit a4ae997adc ("net: mscc: ocelot: initialize watermarks to
sane defaults"), this behavior was somewhat subtle, as the switch had a
more intricately tuned default watermark configuration out of reset,
which did not allow any single port and tc to consume the entire switch
buffer space. Nonetheless, the held frames are still there, and they
reduce the total backplane capacity of the switch.
However, after the aforementioned commit, the behavior can be very
clearly seen, since we deliberately allow each {port, tc} to consume the
entire shared buffer of the switch minus the reservations (and we
disable all reservations by default). That is to say, we allow a
permanently closed tc-taprio gate to hang the entire switch.
A careful inspection of the documentation shows that the QSYS:Q_MAX_SDU
per-port-tc registers serve 2 purposes: one is for guard band calculation
(when zero, this falls back to QSYS:PORT_MAX_SDU), and the other is to
enable oversized frame dropping (when non-zero).
Currently the QSYS:Q_MAX_SDU registers are all zero, so oversized frame
dropping is disabled. The goal of the change is to enable it seamlessly.
For that, we need to hook into the MTU change, tc-taprio change, and
port link speed change procedures, since we depend on these variables.
Frames are not dropped on egress due to a queue system oversize
condition, instead that egress port is simply excluded from the mask of
valid destination ports for the packet. If there are no destination
ports at all, the ingress counter that increments is the generic
"drop_tail" in ethtool -S.
The issue exists in various forms since the tc-taprio offload was introduced.
Fixes: de143c0e27 ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Reported-by: Richie Pearn <richard.pearn@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In vsc9959_tas_clock_adjust(), the INIT_GATE_STATE field is not changed,
only the ENABLE field. Similarly for the disabling of the time-aware
shaper in vsc9959_qos_port_tas_set().
To reflect this, keep the QSYS_TAG_CONFIG_INIT_GATE_STATE_M mask out of
the read-modify-write procedure to make it clearer what is the intention
of the code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future change we will need to remember the entire tc-taprio config
on all ports rather than just the base time, so use the
taprio_offload_get() helper function to replace ocelot_port->base_time
with ocelot_port->taprio.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
of_parse_phandle() will increase the refcount of 'pcs_node', so add
of_node_put() before return from a5psw_pcs_get().
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220630014153.1888811-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c
9c5de246c1 ("net: sparx5: mdb add/del handle non-sparx5 devices")
fbb89d02e3 ("net: sparx5: Allow mdb entries to both CPU and ports")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both PSFP stats and the port stats read by ocelot_check_stats_work() are
indirectly read through the same mechanism - write to STAT_CFG:STAT_VIEW,
read from SYS:STAT:CNT[n].
It's just that for port stats, we write STAT_VIEW with the index of the
port, and for PSFP stats, we write STAT_VIEW with the filter index.
So if we allow them to run concurrently, ocelot_check_stats_work() may
change the view from vsc9959_psfp_counters_get(), and vice versa.
Fixes: 7d4b564d6a ("net: dsa: felix: support psfp filter on vsc9959")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220629183007.3808130-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The devm_platform_ioremap_resource() function never returns NULL.
It returns error pointers.
Signed-off-by: Peng Wu <wupeng58@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Clément Léger <clement.leger@bootlin.com>
Link: https://lore.kernel.org/r/20220628130920.49493-1-wupeng58@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This switch is calculating tx/rx_bytes for all packets including pause.
So, include rx/tx_pause counter to rx/tx_packets to make tx/rx_bytes fit
to rx/tx_packets.
Link: https://lore.kernel.org/all/20220624220317.ckhx6z7cmzegvoqi@skbuf/
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for pause specific stats.
Tested on ksz9477.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch moves the broadcast ctrl, multicast ctrl and start control
registers from ksz_chip_dat to ksz_chip_reg.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the stp_ctrl_reg from the ksz_chip_data to ksz_chip_reg
structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register size for the ksz8 switches is u8 and for ksz9477 series is
u16. To have common struct for ksz series switches the size of reg is
increased from u8 to u16.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the struct ksz8 from ksz8.h which is no longer
needed. The platform bus specific details are now deferenced through
dev->priv.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves ksz8->shifts from ksz8795.c to ksz_common.c. The shifts
are dereferenced using dev->info->shifts.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the ksz8->masks from ksz8795.c to ksz_common.c. The
mask will be dereferenced using dev->info->masks.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the ksz8->regs from ksz8795.c to the ksz_common.c. And
the regs is dereferrenced using dev->info->regs.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commits add forwarding database support to the driver. It
implements fdb_add(), fdb_del() and fdb_dump().
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add statistics support to the rzn1-a5psw driver by implementing the
following dsa_switch_ops callbacks:
- get_sset_count()
- get_strings()
- get_ethtool_stats()
- get_eth_mac_stats()
- get_eth_ctrl_stats()
- get_rmon_stats()
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Renesas RZ/N1 advanced 5 port switch driver. This switch handles 5
ports including 1 CPU management port. A MDIO bus is also exposed by
this switch and allows to communicate with PHYs connected to the ports.
Each switch port (except for the CPU management ports) is connected to
the MII converter.
This driver includes basic bridging support, more support will be added
later (vlan, etc).
Suggested-by: Jean-Pierre Geslin <jean-pierre.geslin@non.se.com>
Suggested-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of now, there are two spi probes, one ksz8795_spi.c and other
ksz9477_spi.c. This patch combines two files into single ksz_spi.c. The
difference between the two are regmap config and struct ksz8. The regmap
config is assigned based on the platform data. And struct ksz8 is left
untouched, as it is used only ksz8795.c. It can be used for all
other switches also in future.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch delete the ksz8_switch_register and ksz9477_switch_register
since both are calling the ksz_switch_register function. Instead the
ksz_switch_register is called from the probe function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch move the ksz_dev_ops from individual files to ksz_common.c.
And the dev_ops is assigned to ksz_device based on the switch detect.
This reduces the redundant function and allows to reuse the
functionality for LAN937x which has similar register set.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the two different menuconfig for ksz9477 and ksz8795
to single ksz_common. so that it can be extended for the other switch
like lan937x. And removes the export_symbols for the extern functions in
the ksz_common.h.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per 'commit 3506b2f42d ("net: dsa: microchip: call
phy_remove_link_mode during probe")' phy_remove_link_mode is added in
the switch_register function after dsa_switch_register. In order to have
the common switch register function, moving this phylink validation to
phylink_get_caps validation hook.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present, ksz8795.c and ksz9477.c have separate dsa_switch_ops
structure initialization. This patch modifies the files such a way that
ksz switches has common dsa_switch_ops in the ksz_common.c file.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch move the setting the start bit from the individual switch
configuration to ksz_setup
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the enabling the multicast storm protection from
individual setup function to ksz_setup function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch move the 10% broadcast protection from the individual setup
to ksz_setup. In the ksz9477, broadcast protection is updated in reset
function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch move the common initialization of switches to ksz_setup and
perform the switch specific initialization using the ksz_dev_ops
function pointer.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to transmit the STP BPDU packet to the CPU port, the STP
address 01-80-c2-00-00-00 has to be added to static alu table for
ksz8795 series switch. For the ksz9477 switch, there is reserved
multicast table which handles forwarding the particular set of
multicast address to cpu port. So enabling the multicast reserved table
and updated the cpu port index. The stp addr is enabled during the setup
phase using the enable_stp_addr pointer in struct ksz_dev_ops.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To have the common set of initialization in ksz_setup, introduced the
new config_cpu_port member to ksz_dev_ops. Since both the ksz8795.c and
ksz9477.c configuring the cpu port in the setup function, introduced the
member.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames the shutdown to reset in ksz_dev_ops in order to use
the reset dev_ops in the ksz_setup.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pause settings reported by the PHY should also be applied to the GMII port
status override otherwise the switch will not generate pause frames towards the
link partner despite the advertisement saying otherwise.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220623030204.1966851-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
of_find_node_by_name() will decrease the refcount of its first arg and
we need a of_node_get() to keep refcount balance.
Fixes: 7d9ee2e8ff ("net: dsa: hellcreek: Add PTP status LEDs")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220622040621.4094304-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, all the device specific speed setting functions convert
SPEED_MAX to the actual speed of the port. Rather than having each
of the mv88e6xxx chip specifics handling SPEED_MAX, derive it from
the mac_capabilities instead.
This is only needed for CPU and DSA ports, so move the logic up into
mv88e6xxx_setup_port() - which allows us to kill off all users of
SPEED_MAX throughout the driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove mv88e6065_port_set_speed_duplex() - this is never called, and
thus is completely redundant.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current mgmt ethernet timeout is set to 100ms. This value is too
big and would slow down any mdio command in case the mgmt ethernet
packet have some problems on the receiving part.
Reduce it to just 5ms to handle case when some operation are done on the
master port that would cause the mgmt ethernet to not work temporarily.
Fixes: 5950c7c0a6 ("net: dsa: qca8k: add support for mgmt read/write in Ethernet packet")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220621151633.11741-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It was discovered that the Documentation lacks of a fundamental detail
on how to correctly change the MAX_FRAME_SIZE of the switch.
In fact if the MAX_FRAME_SIZE is changed while the cpu port is on, the
switch panics and cease to send any packet. This cause the mgmt ethernet
system to not receive any packet (the slow fallback still works) and
makes the device not reachable. To recover from this a switch reset is
required.
To correctly handle this, turn off the cpu ports before changing the
MAX_FRAME_SIZE and turn on again after the value is applied.
Fixes: f58d2598cf ("net: dsa: qca8k: implement the port MTU callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220621151122.10220-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch assigns the get_phy_flags & mtu hook of ksz8795 and ksz9477
in dsa_switch_ops to ksz_common. For get_phy_flags hooks,checks whether
the chip is ksz8863/kss8793 then it returns error for port1.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch makes the dsa_switch_hook for fdbs to use ksz_common.c file.
And from ksz_common, individual switches fdb functions are called using
the dev->dev_ops. And removed the r_dyn_mac_table, r_sta_mac_table and
w_sta_mac_table from ksz_dev_ops as it is used only in ksz8795.c
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ksz_mdb_add/del in ksz_common.c is specific for the ksz8795.c file. The
ksz9477 has its separate ksz9477_port_mdb_add/del functions. This patch
moves the ksz8795 specific mdb functionality from ksz_common to ksz8795.
And this dsa_switch_ops hooks for ksz8795/ksz9477 are invoked through
the ksz_port_mdb_add/del.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch assigns the phylink_get_caps in ksz8795 and ksz9477 to
ksz_phylink_get_caps. And update their mac_capabilities in the
respective ksz_dev_ops.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
At present, P_STP_CTRL register value is passed as parameter to
ksz_port_stp_state from the individual dsa_switch_ops hooks. This patch
update the function to retrieve the register value through the
ksz_chip_data member.
And add the static to ksz_update_port_member since it is not called
outside the ksz_common.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch updates the common port mirror add/del dsa_switch_ops in
ksz_common.c. The individual switches implementation is executed based
on the ksz_dev_ops function pointers.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch moves the vlan dsa_switch_ops such as vlan_add, vlan_del and
vlan_filtering from the individual files ksz8795.c, ksz9477.c to
ksz_common.c file.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ksz8795 and ksz9477 implementation on phy read/write hooks are
different. This patch modifies the ksz9477 implementation same as
ksz8795 by updating the ksz9477_dev_ops structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch move the dsa hook get_tag_protocol to ksz_common file. And
the tag_protocol is returned based on the dev->chip_id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
KSZ87xx and KSZ88xx have chip_id representation at reg location 0. And
KSZ9477 compatible switch and LAN937x switch have same chip_id detection
at location 0x01 and 0x02. To have the common switch detect
functionality for ksz switches, ksz_switch_detect function is
introduced.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ksz9477_switch_detect performs the detecting the chip id from the
location 0x00 and also check gigabit compatibility check & number of
ports based on the register global_options0. To prepare the common ksz
switch detect function, routine other than chip id read is moved to
ksz9477_switch_init.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When adjusting the PTP clock, the base time of the TAS configuration
will become unreliable. We need reset the TAS configuration by using a
new base time.
For example, if the driver gets a base time 0 of Qbv configuration from
user, and current time is 20000. The driver will set the TAS base time
to be 20000. After the PTP clock adjustment, the current time becomes
10000. If the TAS base time is still 20000, it will be a future time,
and TAS entry list will stop running. Another example, if the current
time becomes to be 10000000 after PTP clock adjust, a large time offset
can cause the hardware to hang.
This patch introduces a tas_clock_adjust() function to reset the TAS
module by using a new base time after the PTP clock adjustment. This can
avoid issues above.
Due to PTP clock adjustment can occur at any time, it may conflict with
the TAS configuration. We introduce a new TAS lock to serialize the
access to the TAS registers.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xpcs_config() has 'advertising' input that is required for C37 1000BASE-X
AN in later patch series. So, we prepare xpcs_do_config() for it.
For sja1105, xpcs_do_config() is used for xpcs configuration without
depending on advertising input, so set to NULL.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek switches in the rtl8365mb family always have at least one port
with a so-called external interface, supporting PHY interface modes such
as RGMII or SGMII. The purpose of this patch is to improve the driver's
handling of these ports.
A new struct rtl8365mb_chip_info is introduced together with a static
array of such structs. An instance of this struct is added for each
supported switch, distinguished by its chip ID and version. Embedded in
each chip_info struct is an array of struct rtl8365mb_extint, describing
the external interfaces available. This is more specific than the old
rtl8365mb_extint_port_map, which was only valid for switches with up to
6 ports.
The struct rtl8365mb_extint also contains a bitmask of supported PHY
interface modes, which allows the driver to distinguish which ports
support RGMII. This corrects a previous mistake in the driver whereby it
was assumed that any port with an external interface supports RGMII.
This is not actually the case: for example, the RTL8367S has two
external interfaces, only the second of which supports RGMII. The first
supports only SGMII and HSGMII. This new design will make it easier to
add support for other interface modes.
Finally, rtl8365mb_phylink_get_caps() is fixed up to return supported
capabilities based on the external interface properties described above.
This addresses Vladimir's point in the linked thread that the
capabilities are not actually a function of the DSA port type: Although
most typical applications will treat the ports with internal PHY as user
ports, there is no actual hardware limitation preventing one from using
them as a CPU port. Equally, ports with external interface(s) may well
be treated as user ports, even though it is typical to use those ports
as CPU ports.
Link: https://lore.kernel.org/netdev/20220510192301.5djdt3ghoavxulhl@bang-olufsen.dk/
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable is just assigned the value of a macro, so it can be
removed.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The maximum number of ports is actually 11, according to two
observations:
1. The highest port ID used in the vendor driver is 10. Since port IDs
are indexed from 0, and since DSA follows the same numbering system,
this means up to 11 ports are to be presumed.
2. The registers with port mask fields always amount to a maximum port
mask of 0x7FF, corresponding to a maximum 11 ports.
In view of this, I also deleted the comment.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no real need for this variable: the line change interrupt mask
is sufficiently masked out when getting linkup_ind and linkdown_ind in
the interrupt handler.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The official name of this switch is RTL8367RB-VB, not RTL8367RB. There
is also an RTL8367RB-VC which is rather different. Change the name of
the CHIP_ID/_VER macros for reasons of consistency.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace last occurences of hardcoded cpu-port by cpu_dp member of
dsa_port struct.
Now the constant can be dropped.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enumerate available cpu-ports instead of using hardcoded constant.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rework vlan_add/vlan_del functions in preparation for dynamic cpu port.
Currently BIT(MT7530_CPU_PORT) is added to new_members, even though
mt7530_port_vlan_add() will be called on the CPU port too.
Let DSA core decide when to call port_vlan_add for the CPU port, rather
than doing it implicitly.
We can do autonomous forwarding in a certain VLAN, but not add br0 to that
VLAN and avoid flooding the CPU with those packets, if software knows it
doesn't need to process them.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit a18e6521a7 ("net: phylink: handle NA interface mode in
phylink_fwnode_phy_connect()"), phylib defaults to GMII when no phy-mode
or phy-connection-type property is specified in a DSA port node of the
device tree. The same commit caused a regression in rtl8365mb whereby
phylink would fail to connect, because the driver did not advertise
support for GMII for ports with internal PHY.
It should be noted that the aforementioned regression is not because the
blamed commit was incorrect: on the contrary, the blamed commit is
correcting the previous behaviour whereby unspecified phy-mode would
cause the internal interface mode to be PHY_INTERFACE_MODE_NA. The
rtl8365mb driver only worked by accident before because it _did_
advertise support for PHY_INTERFACE_MODE_NA, despite NA being reserved
for internal use by phylink. With one mistake fixed, the other was
exposed.
Commit a5dba0f207 ("net: dsa: rtl8365mb: add GMII as user port mode")
then introduced implicit support for GMII mode on ports with internal
PHY to allow a PHY connection for device trees where the phy-mode is not
explicitly set to "internal". At this point everything was working OK
again.
Subsequently, commit 6ff6064605 ("net: dsa: realtek: convert to
phylink_generic_validate()") broke this behaviour again by discarding
the usage of rtl8365mb_phy_mode_supported() - where this GMII support
was indicated - while switching to the new .phylink_get_caps API.
With the new API, rtl8365mb_phy_mode_supported() is no longer needed.
Remove it altogether and add back the GMII capability - this time to
rtl8365mb_phylink_get_caps() - so that the above default behaviour works
for ports with internal PHY again.
Fixes: 6ff6064605 ("net: dsa: realtek: convert to phylink_generic_validate()")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20220607184624.417641-1-alvin@pqrs.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Phylink wants to know if the link has dropped since the last time state
was retrieved, and the BMSR gives us that. Read the BMSR and use it when
deciding the link state. Fill in the an_complete member as well for the
emulated PHY state.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Other errors accessing the registers in mv88e6352_serdes_pcs_get_state()
print "PHY " before the register name, except for the BMSR. Make this
consistent with the other error messages.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit ede359d884 ("net: dsa: mv88e6xxx: Link in pcs_get_state() if AN
is bypassed") added the ability to link if AN was bypassed, and added
filling of state->an_complete field, but set it to true if AN was
enabled in BMCR, not when AN was reported complete in BMSR.
This was done because for some reason, when I wanted to use BMSR value
to infer an_complete, I was looking at BMSR_ANEGCAPABLE bit (which was
always 1), instead of BMSR_ANEGCOMPLETE bit.
Use BMSR_ANEGCOMPLETE for filling state->an_complete.
Fixes: ede359d884 ("net: dsa: mv88e6xxx: Link in pcs_get_state() if AN is bypassed")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node.
when breaking early from a for_each_available_child_of_node() loop,
we need to explicitly call of_node_put() on the gphy_fw_np.
Add missing of_node_put() to avoid refcount leak.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220605072335.11257-1-linmq006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This series includes the following patchsets:
- bitmap: optimize bitmap_weight() usage(w/o bitmap_weight_cmp), from me;
- lib/bitmap.c make bitmap_print_bitmask_to_buf parseable, from Mauro
Carvalho Chehab;
- include/linux/find: Fix documentation, from Anna-Maria Behnsen;
- bitmap: fix conversion from/to fix-sized arrays, from me;
- bitmap: Fix return values to be unsigned, from Kees Cook.
It has been in linux-next for at least a week with no problems.
-----BEGIN PGP SIGNATURE-----
iQGzBAABCgAdFiEEi8GdvG6xMhdgpu/4sUSA/TofvsgFAmKaEzYACgkQsUSA/Tof
vsiGKwv8Dgr3G0mLbSfmHZqdFMIsmSmwhxlEH6eBNtX6vjQbGafe/Buhj/1oSY8N
NYC4+5Br6s7MmMRth3Kp6UECdl94TS3Ka06T+lVBKkG+C+B1w1/svqUMM2ZCQF3e
Z5R/HhR6av9X9Qb2mWSasWLkWp629NjdtRsJSDWiVt1emVVwh+iwxQnMH9VuE+ao
z3mvaQfSRhe4h+xCZOiohzFP+0jZb1EnPrQAIVzNUjigo7mglpNvVyO7p/8LU7gD
dIjfGmSbtsHU72J+/0lotRqjhjORl1F/EILf8pIzx5Ga7ExUGhOzGWAj7/3uZxfA
Cp1Z/QV271MGwv/sNdSPwCCJHf51eOmsbyOyUScjb3gFRwIStEa1jB4hKwLhS5wF
3kh4kqu3WGuIQAdxkUpDBsy3CQjAPDkvtRJorwyWGbjwa9xUETESAgH7XCCTsgWc
0sIuldWWaxC581+fAP1Dzmo8uuWBURTaOrVmRMILQHMTw54zoFyLY+VI9gEAT9aV
gnPr3M4F
=U7DN
-----END PGP SIGNATURE-----
Merge tag 'bitmap-for-5.19-rc1' of https://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- bitmap: optimize bitmap_weight() usage, from me
- lib/bitmap.c make bitmap_print_bitmask_to_buf parseable, from Mauro
Carvalho Chehab
- include/linux/find: Fix documentation, from Anna-Maria Behnsen
- bitmap: fix conversion from/to fix-sized arrays, from me
- bitmap: Fix return values to be unsigned, from Kees Cook
It has been in linux-next for at least a week with no problems.
* tag 'bitmap-for-5.19-rc1' of https://github.com/norov/linux: (31 commits)
nodemask: Fix return values to be unsigned
bitmap: Fix return values to be unsigned
KVM: x86: hyper-v: replace bitmap_weight() with hweight64()
KVM: x86: hyper-v: fix type of valid_bank_mask
ia64: cleanup remove_siblinginfo()
drm/amd/pm: use bitmap_{from,to}_arr32 where appropriate
KVM: s390: replace bitmap_copy with bitmap_{from,to}_arr64 where appropriate
lib/bitmap: add test for bitmap_{from,to}_arr64
lib: add bitmap_{from,to}_arr64
lib/bitmap: extend comment for bitmap_(from,to)_arr32()
include/linux/find: Fix documentation
lib/bitmap.c make bitmap_print_bitmask_to_buf parseable
MAINTAINERS: add cpumask and nodemask files to BITMAP_API
arch/x86: replace nodes_weight with nodes_empty where appropriate
mm/vmstat: replace cpumask_weight with cpumask_empty where appropriate
clocksource: replace cpumask_weight with cpumask_empty in clocksource.c
genirq/affinity: replace cpumask_weight with cpumask_empty where appropriate
irq: mips: replace cpumask_weight with cpumask_empty where appropriate
drm/i915/pmu: replace cpumask_weight with cpumask_empty where appropriate
arch/x86: replace cpumask_weight with cpumask_empty where appropriate
...
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
mv88e6xxx_mdio_register() pass the device node to of_mdiobus_register().
We don't need the device node after it.
Add missing of_node_put() to avoid refcount leak.
Fixes: a3c53be55c ("net: dsa: mv88e6xxx: Support multiple MDIO busses")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the VCAP filters to support multiple tag_8021q CPU ports.
TX works using a filter for VLAN ID on the ingress of the CPU port, with
a redirect and a VLAN pop action. This can be updated trivially by
amending the ingress port mask of this rule to match on all tag_8021q
CPU ports.
RX works using a filter for ingress port on the egress of the CPU port,
with a VLAN push action. Here we need to replicate these filters for
each tag_8021q CPU port, and let them all have the same action.
This means that the OCELOT_VCAP_ES0_TAG_8021Q_RXVLAN() cookie needs to
encode a unique value for every {user port, CPU port} pair it's given.
Do this by encoding the CPU port in the upper 16 bits of the cookie, and
the user port in the lower 16 bits.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a desire for the felix driver to gain support for multiple
tag_8021q CPU ports, but the current model prevents it.
This is because ocelot_apply_bridge_fwd_mask() only takes into
consideration whether a port is a tag_8021q CPU port, but not whose CPU
port it is.
We need a model where we can have a direct affinity between an ocelot
port and a tag_8021q CPU port. This serves as the basis for multiple CPU
ports.
Declare a "dsa_8021q_cpu" backpointer in struct ocelot_port which
encodes that affinity. Repurpose the "ocelot_set_dsa_8021q_cpu" API to
"ocelot_assign_dsa_8021q_cpu" to express the change of paradigm.
Note that this change makes the first practical use of the new
ocelot_port->index field in ocelot_port_unassign_dsa_8021q_cpu(), where
we need to remove the old tag_8021q CPU port from the reserved VLAN range.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Absorb the final details of calling ocelot_port_{,un}set_dsa_8021q_cpu(),
i.e. the need to lock &ocelot->fwd_domain_lock, into the callee, to
simplify the caller and permit easier code reuse later.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more logic to ocelot_port_{,un}set_dsa_8021q_cpu() from the ocelot
switch lib by encapsulating the ocelot_apply_bridge_fwd_mask() call that
felix used to have.
This is necessary because the CPU port change procedure will also need
to do this, and it's good to reduce code duplication by having an entry
point in the ocelot switch lib that does all that is needed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PGID_CPU must be updated every time a port is configured or unconfigured
as a tag_8021q CPU port. The ocelot switch lib already has a hook for
that operation, so move the updating of PGID_CPU to those hooks.
These bits are pretty specific to DSA, so normally I would keep them out
of the common switch lib, but when tag_8021q is in use, this has
implications upon the forwarding mask determined by
ocelot_apply_bridge_fwd_mask() and called extensively by the switch lib.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PGID_BC is configured statically by ocelot_init() to flood towards the
CPU port module, and dynamically by ocelot_port_set_bcast_flood()
towards all user ports.
When the tagging protocol changes, the intention is to turn off flooding
towards the old pipe towards the host, and to turn it on towards the new
pipe.
Due to a recent change which removed the adjustment of PGID_BC from
felix_set_host_flood(), 3 things happen.
- when we change from NPI to tag_8021q mode: in this mode, the CPU port
module is accessed via registers, and used to read PTP packets with
timestamps. We fail to disable broadcast flooding towards the CPU port
module, and to enable broadcast flooding towards the physical port
that serves as a DSA tag_8021q CPU port.
- from tag_8021q to NPI mode: in this mode, the CPU port module is
redirected to a physical port. We fail to disable broadcast flooding
towards the physical tag_8021q CPU port, and to enable it towards the
CPU port module at ocelot->num_phys_ports.
- when the ports are put in promiscuous mode, we also fail to update
PGID_BC towards the host pipe of the current protocol.
First issue means that felix_check_xtr_pkt() has to do extra work,
because it will not see only PTP packets, but also broadcasts. It needs
to dequeue these packets just to drop them.
Third issue is inconsequential, since PGID_BC is allocated from the
nonreserved multicast PGID space, and these PGIDs are conveniently
initialized to 0x7f (i.e. flood towards all ports except the CPU port
module). Broadcasts reach the NPI port via ocelot_init(), and reach the
tag_8021q CPU port via the hardware defaults.
Second issue is also inconsequential, because we fail both at disabling
and at enabling broadcast flooding on a port, so the defaults mentioned
above are preserved, and they are fine except for the performance impact.
Fixes: 7a29d220f4 ("net: dsa: felix: reimplement tagging protocol change with function pointers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since kconfig 'select' does not follow dependency chains, if symbol KSA
selects KSB, then KSA should also depend on the same symbols that KSB
depends on, in order to prevent Kconfig warnings and possible build
errors.
Change NET_DSA_SMSC_LAN9303_I2C and NET_DSA_SMSC_LAN9303_MDIO so that
they are limited to VLAN_8021Q if the latter is enabled. This prevents
the Kconfig warning:
WARNING: unmet direct dependencies detected for NET_DSA_SMSC_LAN9303
Depends on [m]: NETDEVICES [=y] && NET_DSA [=y] && (VLAN_8021Q [=m] || VLAN_8021Q [=m]=n)
Selected by [y]:
- NET_DSA_SMSC_LAN9303_I2C [=y] && NETDEVICES [=y] && NET_DSA [=y] && I2C [=y]
Fixes: 430065e267 ("net: dsa: lan9303: add VLAN IDs to master device")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Juergen Borleis <jbe@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Mans Rullgard <mans@mansr.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gswip_port_fdb_dump() reads the MAC bridge entries. The error message
should say "failed to read mac bridge entry". While here, also add the
index to the error print so humans can get to the cause of the problem
easier.
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The first N entries in priv->vlans are reserved for managing ports which
are not part of a bridge. Use priv->hw_info->max_ports to consistently
access per-bridge entries at index 7. Starting at
priv->hw_info->cpu_port (6) is harmless in this case because
priv->vlan[6].bridge is always NULL so the comparison result is always
false (which results in this entry being skipped).
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The name, regs_size and overrides members in struct ksz_device are
unused. Hence remove it.
And host_mask is used in only place of ksz8795.c file, which can be
replaced by dev->info->cpu_ports
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for phylink_get_caps for ksz8795 and ksz9477
series switch. It updates the struct ksz_switch_chip with the details of
the internal phys and xmii interface. Then during the get_caps based on
the bits set in the structure, corresponding phy mode is set.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mib->cnt_ptr resetting is handled in multiple places as part of
port_init_cnt(). Hence moved mib->cnt_ptr code to ksz common layer
and removed from individual product files.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz8795 and ksz9477 uses the same algorithm for copying the ethtool
strings. Hence moved to ksz_common to remove the redundant code.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz8795 and ksz9477 init function initializes the memory to dev->ports,
mib counters and assigns the ds real number of ports. Since both the
routines are same, moved the allocation of port memory to
ksz_switch_register after init.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz88xx family has one set of mib_names. The ksz87xx, ksz9477,
LAN937x based switches has one set of mib_names. In order to remove
redundant declaration, moved the struct mib_names to ksz_chip_data
structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch perform the compatibility check for the device after the chip
detect is done. It is to prevent the mismatch between the device
compatible specified in the device tree and actual device found during
the detect. The ksz9477 device doesn't use any .data in the
of_device_id. But the ksz8795_spi uses .data for assigning the regmap
between 8830 family and 87xx family switch. Changed the regmap
assignment based on the chip_id from the .data.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the ksz_chip_data in ksz8795 and ksz9477 to ksz_common.
At present, the dev->chip_id is iterated with the ksz_chip_data and then
copy its value to the ksz_dev structure. These values are declared as
constant.
Instead of copying the values and referencing it, this patch update the
dev->info to the ksz_chip_data based on the chip_id in the init
function. And also update the ksz_chip_data values for the LAN937x based
switches.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port_cnt value in the structure is not used in the switch_init.
Instead it uses the fls(chip->cpu_port), this is due to one of port in
the ksz8794 unavailable. The cpu_port for the 8794 is 0x10, fls(0x10) =
5, hence updating it directly in the ksz_chip_data structure in order to
same with all the other switches in ksz8795.c and ksz9477.c files.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ocelot switch lib is unaware of the index of a struct
ocelot_port, since that is kept in the encapsulating structures of outer
drivers (struct dsa_port :: index, struct ocelot_port_private :: chip_port).
With the upcoming increase in complexity associated with assigning DSA
tag_8021q CPU ports to certain user ports, it becomes necessary for the
switch lib to be able to retrieve the index of a certain ocelot_port.
Therefore, introduce a new u8 to ocelot_port (same size as the chip_port
used by the ocelot switchdev driver) and rework the existing code to
populate and use it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The error handling for the current tagging protocol change procedure is
a bit brittle (we dismantle the previous tagging protocol entirely
before setting up the new one). By identifying which parts of a tagging
protocol are unique to itself and which parts are shared with the other,
we can implement a protocol change procedure where error handling is a
bit more robust, because we start setting up the new protocol first, and
tear down the old one only after the setup of the specific and shared
parts succeeded.
The protocol change is a bit too open-coded too, in the area of
migrating host flood settings and MDBs. By identifying what differs
between tagging protocols (the forwarding masks for host flooding) we
can implement a more straightforward migration procedure which is
handled in the shared portion of the protocol change, rather than
individually by each protocol.
Therefore, a more structured approach calls for the introduction of a
structure of function pointers per tagging protocol. This covers setup,
teardown and the host forwarding mask. In the future it will also cover
how to prepare for a new DSA master.
The initial tagging protocol setup (at driver probe time) and the final
teardown (at driver removal time) are also adapted to call into the
structured methods of the specific protocol in current use. This is
especially relevant for teardown, where we previously called
felix_del_tag_protocol() only for the first CPU port. But by not
specifying which CPU port this is for, we gain more flexibility to
support multiple CPU ports in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ocelot switches support a single active CPU port at a time (at least as
a trapping destination, i.e. for control traffic). This is true
regardless of whether we are using the native copy-to-CPU-port-module
functionality, or a redirect action towards the software-defined
tag_8021q CPU port.
Currently we assume that the trapping destination in tag_8021q mode is
the first CPU port, yet in the future we may want to migrate the user
ports to the second CPU port.
For that to work, we need to make sure that the tag_8021q trapping
destination is a CPU port that is active, i.e. is used by at least some
user port on which the trap was added. Otherwise, we may end up
redirecting the traffic to a CPU port which isn't even up.
Note that due to the current design where we simply choose the CPU port
of the first port from the trap's ingress port mask, it may be that a
CPU port absorbes control traffic from user ports which aren't affine to
it as per user space's request. This isn't ideal, but is the lesser of
two evils. Following the user-configured affinity for traps would mean
that we can no longer reuse a single TCAM entry for multiple traps,
which is what we actually do for e.g. PTP. Either we duplicate and
deduplicate TCAM entries on the fly when user-to-CPU-port mappings
change (which is unnecessarily complicated), or we redirect trapped
traffic to all tag_8021q CPU ports if multiple such ports are in use.
The latter would have actually been nice, if it actually worked, but it
doesn't, since a OCELOT_MASK_MODE_REDIRECT action towards multiple ports
would not take PGID_SRC into consideration, and it would just duplicate
the packet towards each (CPU) port, leading to duplicates in software.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
