The bug is here:
return rule;
The list iterator value 'rule' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty or no element
is found.
To fix the bug, return 'rule' when found, otherwise return NULL.
Fixes: ae7a5aff78 ("net: dsa: bcm_sf2: Keep copy of inserted rules")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220328032431.22538-1-xiam0nd.tong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some chips using the split VTU/STU design will not accept VTU entries
who's SID points to an invalid STU entry. Therefore, mark all those
chips with either the mv88e6352_g1_stu_* or mv88e6390_g1_stu_* ops as
appropriate.
Notably, chips for the Opal Plus (6085/6097) era seem to use a
different implementation than those from Agate (6352) and onwards,
even though their external interface is the same. The former happily
accepts VTU entries referencing invalid STU entries, while the latter
does not.
This fixes an issue where the driver would fail to probe switch trees
that contained chips of the Agate/Topaz generation which did not
declare STU support, as loaded VTU entries would be read back as
invalid.
Fixes: 49c98c1dc7 ("net: dsa: mv88e6xxx: Disentangle STU from VTU")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220319110345.555270-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the same way that we check for STU support in the MST state
callback, we should also verify it before trying to change a VLANs
MSTI membership.
Fixes: acaf4d2e36 ("net: dsa: mv88e6xxx: MST Offloading")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simply having a physical STU table in the device doesn't do us any
good if there's no implementation of the relevant ops to access that
table. So ensure that chips that claim STU support can also talk to
the hardware.
This fixes an issue where chips that had a their ->info->max_sid
set (due to their family membership), but no implementation (due to
their chip-specific ops struct) would fail to probe.
Fixes: 49c98c1dc7 ("net: dsa: mv88e6xxx: Disentangle STU from VTU")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gain support for port mirroring using tc-matchall by forwarding the
calls to the ocelot switch library.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drivers might have error messages to propagate to user space, most
common being that they support a single mirror port.
Propagate the netlink extack so that they can inform user space in a
verbal way of their limitations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allocate a SID in the STU for each MSTID in use by a bridge and handle
the mapping of MSTIDs to VLANs using the SID field of each VTU entry.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Export the raw STU data in a devlink region so that it can be
inspected from userspace and compared to the current bridge
configuration.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In early LinkStreet silicon (e.g. 6095/6185), the per-VLAN STP states
were kept in the VTU - there was no concept of a SID. Later, the
information was split into two tables, where the VTU only tracked
memberships and deferred the STP state tracking to the STU via a
pointer (SID). This meant that a group of VLANs could share the same
STU entry. Most likely, this was done to align with MSTP (802.1Q-2018,
Clause 13), which is built on this principle.
While the VTU is still 4k lines on most devices, the STU is capped at
64 entries. This means that the current stategy, updating STU info
whenever a VTU entry is updated, can not easily support MSTP because:
- The maximum number of VIDs would also be capped at 64, as we would
have to allocate one SID for every VTU entry - even if many VLANs
would effectively share the same MST.
- MSTP updates would be unnecessarily slow as you would have to
iterate over all VLANs that share the same MST.
In order to support MSTP offloading in the future, manage the STU as a
separate entity from the VTU.
Only add support for newer hardware with separate VTU and
STU. VTU-only devices can also be supported, but essentially this
requires a software implementation of an STU (fanning out state
changed to all VLANs tied to the same MST).
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Follow the established programming model for this driver and provide
shims in the felix DSA driver which call the implementations from the
ocelot switch lib. The ocelot switchdev driver wasn't integrated with
dcbnl due to lack of hardware availability.
The switch doesn't have any fancy QoS classification enabled by default.
The provided getters will create a default-prio app table entry of 0,
and no dscp entry. However, the getters have been made to actually
retrieve the hardware configuration rather than static values, to be
future proof in case DSA will need this information from more call paths.
For default-prio, there is a single field per port, in ANA_PORT_QOS_CFG,
called QOS_DEFAULT_VAL.
DSCP classification is enabled per-port, again via ANA_PORT_QOS_CFG
(field QOS_DSCP_ENA), and individual DSCP values are configured as
trusted or not through register ANA_DSCP_CFG (replicated 64 times).
An untrusted DSCP value falls back to other QoS classification methods.
If trusted, the selected ANA_DSCP_CFG register also holds the QoS class
in the QOS_DSCP_VAL field.
The hardware also supports DSCP remapping (DSCP value X is translated to
DSCP value Y before the QoS class is determined based on the app table
entry for Y) and DSCP packet rewriting. The dcbnl framework, for being
so flexible in other useless areas, doesn't appear to support this.
So this functionality has been left out.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add spi_device_id tables to avoid logs like "SPI driver ksz9477-switch
has no spi_device_id".
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables non-standard MTUs on a per-port basis, with the overall
frame size set based on the CPU port.
When the MTU is not changed, this should have no effect.
Long packets crash the switch with MTUs of greater than 2526, so the
maximum is limited for now. Medium packets are sometimes dropped (e.g.
TCP over 2477, UDP over 2516-2519, ICMP over 2526), Hence an MTU value
of 2400 seems safe.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://lore.kernel.org/r/20220308230457.1599237-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This chips supports two ways to configure max MTU size:
- by setting SW_LEGAL_PACKET_DISABLE bit: if this bit is 0 allowed packed size
will be between 64 and bytes 1518. If this bit is 1, it will accept
packets up to 2000 bytes.
- by setting SW_JUMBO_PACKET bit. If this bit is set, the chip will
ignore SW_LEGAL_PACKET_DISABLE value and use REG_SW_MTU__2 register to
configure MTU size.
Current driver has disabled SW_JUMBO_PACKET bit and activates
SW_LEGAL_PACKET_DISABLE. So the switch will pass all packets up to 2000 without
any way to configure it.
By providing port_change_mtu we are switch to SW_JUMBO_PACKET way and will
be able to configure MTU up to ~9000.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220308135857.1119028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Felix driver declares FDB isolation but puts all standalone ports in
VID 0. This is mostly problem-free as discussed with Alvin here:
https://patchwork.kernel.org/project/netdevbpf/cover/20220302191417.1288145-1-vladimir.oltean@nxp.com/#24763870
however there is one catch. DSA still thinks that FDB entries are
installed on the CPU port as many times as there are user ports, and
this is problematic when multiple user ports share the same MAC address.
Consider the default case where all user ports inherit their MAC address
from the DSA master, and then the user runs:
ip link set swp0 address 00:01:02:03:04:05
The above will make dsa_slave_set_mac_address() call
dsa_port_standalone_host_fdb_add() for 00:01:02:03:04:05 in port 0's
standalone database, and dsa_port_standalone_host_fdb_del() for the old
address of swp0, again in swp0's standalone database.
Both the ->port_fdb_add() and ->port_fdb_del() will be propagated down
to the felix driver, which will end up deleting the old MAC address from
the CPU port. But this is still in use by other user ports, so we end up
breaking unicast termination for them.
There isn't a problem in the fact that DSA keeps track of host
standalone addresses in the individual database of each user port: some
drivers like sja1105 need this. There also isn't a problem in the fact
that some drivers choose the same VID/FID for all standalone ports.
It is just that the deletion of these host addresses must be delayed
until they are known to not be in use any longer, and only the driver
has this knowledge. Since DSA keeps these addresses in &cpu_dp->fdbs and
&cpu_db->mdbs, it is just a matter of walking over those lists and see
whether the same MAC address is present on the CPU port in the port db
of another user port.
I have considered reusing the generic dsa_port_walk_fdbs() and
dsa_port_walk_mdbs() schemes for this, but locking makes it difficult.
In the ->port_fdb_add() method and co, &dp->addr_lists_lock is held, but
dsa_port_walk_fdbs() also acquires that lock. Also, even assuming that
we introduce an unlocked variant of the address iterator, we'd still
need some relatively complex data structures, and a void *ctx in the
dsa_fdb_walk_cb_t which we don't currently pass, such that drivers are
able to figure out, after iterating, whether the same MAC address is or
isn't present in the port db of another port.
All the above, plus the fact that I expect other drivers to follow the
same model as felix where all standalone ports use the same FID, made me
conclude that a generic method provided by DSA is necessary:
dsa_fdb_present_in_other_db() and the mdb equivalent. Felix calls this
from the ->port_fdb_del() handler for the CPU port, when the database
was classified to either a port db, or a LAG db.
For symmetry, we also call this from ->port_fdb_add(), because if the
address was installed once, then installing it a second time serves no
purpose: it's already in hardware in VID 0 and it affects all standalone
ports.
This change moves dsa_db_equal() from switch.c to dsa.c, since it now
has one more caller.
Fixes: 54c3198460 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two blamed commits were written/tested individually but not
together.
When put together, commit 90897569be ("net: dsa: felix: start off with
flooding disabled on the CPU port"), which deletes a reinitialization of
PGID_UC/PGID_MC/PGID_BC, is no longer sufficient to ensure that these
port masks don't contain the CPU port module.
This is because commit b903a6bd2e ("net: dsa: felix: migrate flood
settings from NPI to tag_8021q CPU port") overwrites the hardware
default settings towards the CPU port module with the settings that used
to be present on the NPI port treated as a regular port. There, flooding
is enabled, so flooding would get enabled on the CPU port module too.
Adding conditional logic somewhere within felix_setup_tag_npi() to
configure either the default no-flood policy or the flood policy
inherited from the tag_8021q CPU port from a previous call to
dsa_port_manage_cpu_flood() is getting complicated. So just let the
migration logic do its thing during initial setup (which will
temporarily turn on flooding), then turn flooding off for the NPI port
after felix_set_tag_protocol() finishes. Here we are in felix_setup(),
so the DSA slave interfaces are not yet created, and this doesn't affect
traffic in any way.
Fixes: 90897569be ("net: dsa: felix: start off with flooding disabled on the CPU port")
Fixes: b903a6bd2e ("net: dsa: felix: migrate flood settings from NPI to tag_8021q CPU port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer need the workaround in the felix driver to avoid calling
dsa_port_walk_fdbs() when &dp->fdbs is an uninitialized list, because
that list is now initialized from all call paths of felix_set_tag_protocol().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Discussing one of the tests in mt753x_phylink_validate() with Landen
Chao confirms that the "||" should be "&&". Fix this.
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1nRCF0-00CiXD-7q@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The trailing tag is also supported by this family. The default is still
rtl8_4 but now the switch supports changing the tag to rtl8_4t.
Reintroduce the dropped cpu in struct rtl8365mb (removed by 6147631).
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to an apparently incorrect conflict resolution on my part in commit
54c3198460 ("net: mscc: ocelot: enforce FDB isolation when
VLAN-unaware"), "ocelot->ports[port]->is_dsa_8021q_cpu = false" was
supposed to be replaced by "ocelot_port_unset_dsa_8021q_cpu(ocelot, port)"
which does the same thing, and more. But now we have both, so the direct
assignment is redundant. Remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet extraction failures over register-based MMIO are silent, and
difficult to pinpoint. Add an error message to remedy this.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Automated tools complain that felix_check_xtr_pkt() has logic to drain
the CPU queue on the reception of a PTP packet over Ethernet, yet it
returns an uninitialized error code in the case where the CPU queue was
empty.
This is not likely to happen (/possible if hardware works correctly),
but it isn't a fatal condition either. The PTP packet will be dequeued
from the CPU queue when the next PTP packet arrives. So initialize "err"
to 0 for the case where nothing was dequeued during this iteration.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA ->port_rxtstamp() function is never called for PTP_CLASS_NONE:
dsa_skb_defer_rx_timestamp:
if (type == PTP_CLASS_NONE)
return false;
if (likely(ds->ops->port_rxtstamp))
return ds->ops->port_rxtstamp(ds, p->dp->index, skb, type);
So practically, the argument is unused, so remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This assignment is redundant, since ocelot->npi has already been set to
-1 by felix_npi_port_deinit(). Call path:
felix_change_tag_protocol
-> felix_del_tag_protocol(DSA_TAG_PROTO_OCELOT)
-> felix_teardown_tag_npi
-> felix_npi_port_deinit
-> felix_set_tag_protocol(DSA_TAG_PROTO_OCELOT_8021Q)
-> felix_setup_tag_8021q
-> felix_8021q_cpu_port_init
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
felix_migrate_flood_to_tag_8021q_port() takes care of clearing the
flooding bits on the old CPU port (which was the CPU port module), so
manually clearing this bit from PGID_UC, PGID_MC, PGID_BC is redundant.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver probes with all ports as standalone, and it supports unicast
filtering. So DSA will call port_fdb_add() for all necessary addresses
on the current CPU port. We also handle migrations when the CPU port
hardware resource changes (on tagging protocol change), so there should
not be any unknown address that we have to receive while not promiscuous.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the tagging protocol changes from "ocelot" to "ocelot-8021q" or in
reverse, the DSA promiscuity setting that was applied for the old CPU
port must be transferred to the new one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "ocelot" and "ocelot-8021q" tagging protocols make use of different
hardware resources, and host FDB entries have different destination
ports in the switch analyzer module, practically speaking.
So when the user requests a tagging protocol change, the driver must
migrate all host FDB and MDB entries from the NPI port (in fact CPU port
module) towards the same physical port, but this time used as a regular
port.
It is pointless for the felix driver to keep a copy of the host
addresses, when we can create and export DSA helpers for walking through
the addresses that it already needs to keep on the CPU port, for
refcounting purposes.
felix_classify_db() is moved up to avoid a forward declaration.
We pass "bool change" because dp->fdbs and dp->mdbs are uninitialized
lists when felix_setup() first calls felix_set_tag_protocol(), so we
need to avoid calling dsa_port_walk_fdbs() during probe time.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series from Uwe Kleine-König converts the spi remove function to
return void since there is nothing useful that we can do with a failure
and it as more buses are converted it'll enable further work on the
driver core.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmIdBQAACgkQJNaLcl1U
h9D1GQf/dVustBx4kCUNJt4QuMF4rozHtAzo2qK1grAnpHEqiMvVEzAuxfbTgJOx
9AUj+xEuVpPxoYUDLVJpJrxwdAl0Ue8tDRgP9Cqr/o6a3IoKrhEi+1KpSbvjcsgB
oqJEcvdjk1XAtl+QXmvyMjbMLxpz2x3Ne6dj7RL/LsfxXC0/om+NQIvJBfn78Dj2
JSNJcVtRDmdaApXfguDGA0u3COarypybYMuumIO4rRxjA5S4FXXovny4nwNXvOhS
Ki5/7GKq9rojeeIf0kD/IDdkmSS0WZp3Rc2mIrdsrXrTca+dTo3sYlcP+HMcZmtW
0+bzsht6VyApfGGZ1Ra/w3NxN6OMMg==
=TyvV
-----END PGP SIGNATURE-----
Merge tag 'spi-remove-void' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark Brown says:
====================
spi: Make remove() return void
This series from Uwe Kleine-König converts the spi remove function to
return void since there is nothing useful that we can do with a failure
and it as more buses are converted it'll enable further work on the
driver core.
====================
Link: https://lore.kernel.org/r/20220228173957.1262628-2-broonie@kernel.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All users of the felix driver were creating their own prevalidate_phy_mode
function. The same logic can be performed in a more general way by using a
simple array of bit fields.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As more police parameters are passed to flow_offload, driver can check
them to make sure hardware handles packets in the way indicated by tc.
The conform-exceed control should be drop/pipe or drop/ok. Besides,
for drop/ok, the police should be the last action. As hardware can't
configure peakrate/avrate/overhead, offload should not be supported if
any of them is configured.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ocelot uses a pvid of 0 for standalone ports and ports under a
VLAN-unaware bridge, and the pvid of the bridge for ports under a
VLAN-aware bridge. Standalone ports do not perform learning, but packets
received on them are still subject to FDB lookups. So if the MAC DA that
a standalone port receives has been also learned on a VLAN-unaware
bridge port, ocelot will attempt to forward to that port, even though it
can't, so it will drop packets.
So there is a desire to avoid that, and isolate the FDBs of different
bridges from one another, and from standalone ports.
The ocelot switch library has two distinct entry points: the felix DSA
driver and the ocelot switchdev driver.
We need to code up a minimal bridge_num allocation in the ocelot
switchdev driver too, this is copied from DSA with the exception that
ocelot does not care about DSA trees, cross-chip bridging etc. So it
only looks at its own ports that are already in the same bridge.
The ocelot switchdev driver uses the bridge_num it has allocated itself,
while the felix driver uses the bridge_num allocated by DSA. They are
both stored inside ocelot_port->bridge_num by the common function
ocelot_port_bridge_join() which receives the bridge_num passed by value.
Once we have a bridge_num, we can only use it to enforce isolation
between VLAN-unaware bridges. As far as I can see, ocelot does not have
anything like a FID that further makes VLAN 100 from a port be different
to VLAN 100 from another port with regard to FDB lookup. So we simply
deny multiple VLAN-aware bridges.
For VLAN-unaware bridges, we crop the 4000-4095 VLAN region and we
allocate a VLAN for each bridge_num. This will be used as the pvid of
each port that is under that VLAN-unaware bridge, for as long as that
bridge is VLAN-unaware.
VID 0 remains only for standalone ports. It is okay if all standalone
ports use the same VID 0, since they perform no address learning, the
FDB will contain no entry in VLAN 0, so the packets will always be
flooded to the only possible destination, the CPU port.
The CPU port module doesn't need to be member of the VLANs to receive
packets, but if we use the DSA tag_8021q protocol, those packets are
part of the data plane as far as ocelot is concerned, so there it needs
to. Just ensure that the DSA tag_8021q CPU port is a member of all
reserved VLANs when it is created, and is removed when it is deleted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For sja1105, to enforce FDB isolation simply means to turn on
Independent VLAN Learning unconditionally, and to remap VLAN-unaware FDB
and MDB entries towards the private VLAN allocated by tag_8021q for each
bridge.
Standalone ports each have their own standalone tag_8021q VLAN. No
learning happens in that VLAN due to:
- learning being disabled on standalone user ports
- learning being disabled on the CPU port (we use
assisted_learning_on_cpu_port which only installs bridge FDBs)
VLAN-aware ports learn FDB entries with the bridge VLANs.
VLAN-unaware bridge ports learn with the tag_8021q VLAN for bridging.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As FDB isolation cannot be enforced between VLAN-aware bridges in lack
of hardware assistance like extra FID bits, it seems plausible that many
DSA switches cannot do it. Therefore, they need to reject configurations
with multiple VLAN-aware bridges from the two code paths that can
transition towards that state:
- joining a VLAN-aware bridge
- toggling VLAN awareness on an existing bridge
The .port_vlan_filtering method already propagates the netlink extack to
the driver, let's propagate it from .port_bridge_join too, to make sure
that the driver can use the same function for both.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For DSA, to encourage drivers to perform FDB isolation simply means to
track which bridge does each FDB and MDB entry belong to. It then
becomes the driver responsibility to use something that makes the FDB
entry from one bridge not match the FDB lookup of ports from other
bridges.
The top-level functions where the bridge is determined are:
- dsa_port_fdb_{add,del}
- dsa_port_host_fdb_{add,del}
- dsa_port_mdb_{add,del}
- dsa_port_host_mdb_{add,del}
aka the pre-crosschip-notifier functions.
Changing the API to pass a reference to a bridge is not superfluous, and
looking at the passed bridge argument is not the same as having the
driver look at dsa_to_port(ds, port)->bridge from the ->port_fdb_add()
method.
DSA installs FDB and MDB entries on shared (CPU and DSA) ports as well,
and those do not have any dp->bridge information to retrieve, because
they are not in any bridge - they are merely the pipes that serve the
user ports that are in one or multiple bridges.
The struct dsa_bridge associated with each FDB/MDB entry is encapsulated
in a larger "struct dsa_db" database. Although only databases associated
to bridges are notified for now, this API will be the starting point for
implementing IFF_UNICAST_FLT in DSA. There, the idea is to install FDB
entries on the CPU port which belong to the corresponding user port's
port database. These are supposed to match only when the port is
standalone.
It is better to introduce the API in its expected final form than to
introduce it for bridges first, then to have to change drivers which may
have made one or more assumptions.
Drivers can use the provided bridge.num, but they can also use a
different numbering scheme that is more convenient.
DSA must perform refcounting on the CPU and DSA ports by also taking
into account the bridge number. So if two bridges request the same local
address, DSA must notify the driver twice, once for each bridge.
In fact, if the driver supports FDB isolation, DSA must perform
refcounting per bridge, but if the driver doesn't, DSA must refcount
host addresses across all bridges, otherwise it would be telling the
driver to delete an FDB entry for a bridge and the driver would delete
it for all bridges. So introduce a bool fdb_isolation in drivers which
would make all bridge databases passed to the cross-chip notifier have
the same number (0). This makes dsa_mac_addr_find() -> dsa_db_equal()
say that all bridge databases are the same database - which is
essentially the legacy behavior.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_8021q_bridge_tx_fwd_offload_vid is no longer used just for
bridge TX forwarding offload, it is the private VLAN reserved for
VLAN-unaware bridging in a way that is compatible with FDB isolation.
So just rename it dsa_tag_8021q_bridge_vid.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the old Shared VLAN Learning mode of operation that tag_8021q
previously used for forwarding, we needed to have distinct concepts for
an RX and a TX VLAN.
An RX VLAN could be installed on all ports that were members of a given
bridge, so that autonomous forwarding could still work, while a TX VLAN
was dedicated for precise packet steering, so it just contained the CPU
port and one egress port.
Now that tag_8021q uses Independent VLAN Learning and imprecise RX/TX
all over, those lines have been blurred and we no longer have the need
to do precise TX towards a port that is in a bridge. As for standalone
ports, it is fine to use the same VLAN ID for both RX and TX.
This patch changes the tag_8021q format by shifting the VLAN range it
reserves, and halving it. Previously, our DIR bits were encoding the
VLAN direction (RX/TX) and were set to either 1 or 2. This meant that
tag_8021q reserved 2K VLANs, or 50% of the available range.
Change the DIR bits to a hardcoded value of 3 now, which makes tag_8021q
reserve only 1K VLANs, and a different range now (the last 1K). This is
done so that we leave the old format in place in case we need to return
to it.
In terms of code, the vid_is_dsa_8021q_rxvlan and vid_is_dsa_8021q_txvlan
functions go away. Any vid_is_dsa_8021q is both a TX and an RX VLAN, and
they are no longer distinct. For example, felix which did different
things for different VLAN types, now needs to handle the RX and the TX
logic for the same VLAN.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The felix driver, which also has a tagging protocol implementation based
on tag_8021q, does not care about adding the RX VLAN that is pvid on one
port on the other ports that are in the same bridge with it. It simply
doesn't need that, because in its implementation, the RX VLAN that is
pvid of a port is only used to install a TCAM rule that pushes that VLAN
ID towards the CPU port.
Now that tag_8021q no longer performs Shared VLAN Learning based
forwarding, the RX VLANs are actually segregated into two types:
standalone VLANs and VLAN-unaware bridging VLANs. Since you actually
have to call dsa_tag_8021q_bridge_join() to get a bridging VLAN from
tag_8021q, and felix does not do that because it doesn't need it, it
means that it only gets standalone port VLANs from tag_8021q. Which is
perfect because this means it can drop its workarounds that avoid the
VLANs it does not need.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For VLAN-unaware bridging, tag_8021q uses something perhaps a bit too
tied with the sja1105 switch: each port uses the same pvid which is also
used for standalone operation (a unique one from which the source port
and device ID can be retrieved when packets from that port are forwarded
to the CPU). Since each port has a unique pvid when performing
autonomous forwarding, the switch must be configured for Shared VLAN
Learning (SVL) such that the VLAN ID itself is ignored when performing
FDB lookups. Without SVL, packets would always be flooded, since FDB
lookup in the source port's VLAN would never find any entry.
First of all, to make tag_8021q more palatable to switches which might
not support Shared VLAN Learning, let's just use a common VLAN for all
ports that are under the same bridge.
Secondly, using Shared VLAN Learning means that FDB isolation can never
be enforced. But if all ports under the same VLAN-unaware bridge share
the same VLAN ID, it can.
The disadvantage is that the CPU port can no longer perform precise
source port identification for these packets. But at least we have a
mechanism which has proven to be adequate for that situation: imprecise
RX (dsa_find_designated_bridge_port_by_vid), which is what we use for
termination on VLAN-aware bridges.
The VLAN ID that VLAN-unaware bridges will use with tag_8021q is the
same one as we were previously using for imprecise TX (bridge TX
forwarding offload). It is already allocated, it is just a matter of
using it.
Note that because now all ports under the same bridge share the same
VLAN, the complexity of performing a tag_8021q bridge join decreases
dramatically. We no longer have to install the RX VLAN of a newly
joining port into the port membership of the existing bridge ports.
The newly joining port just becomes a member of the VLAN corresponding
to that bridge, and the other ports are already members of it from when
they joined the bridge themselves. So forwarding works properly.
This means that we can unhook dsa_tag_8021q_bridge_{join,leave} from the
cross-chip notifier level dsa_switch_bridge_{join,leave}. We can put
these calls directly into the sja1105 driver.
With this new mode of operation, a port controlled by tag_8021q can have
two pvids whereas before it could only have one. The pvid for standalone
operation is different from the pvid used for VLAN-unaware bridging.
This is done, again, so that FDB isolation can be enforced.
Let tag_8021q manage this by deleting the standalone pvid when a port
joins a bridge, and restoring it when it leaves it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot DSA driver does not make use of the speed, duplex, pause or
advertisement in its phylink_mac_config() implementation, so it can be
marked as a non-legacy driver.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the PCS selection to use mac_select_pcs, which allows the PCS
to perform any validation it needs, and removes the need to set the PCS
in the mac_config() callback, delving into the higher DSA levels to do
so.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the supported interfaces bitmap is populated, phylink will itself
check that the interface mode is present in this bitmap. Drivers no
longer need to perform this check themselves. Remove these checks.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces bitmap for the Ocelot DSA switches.
Since all sub-drivers only support a single interface mode, defined by
ocelot_port->phy_mode, we can handle this in the main driver code
without reference to the sub-driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently an invalid port throws a WARN_ON warning however invalid
uninitialized values in reg and cpu_port_index are being used later
on. Fix this by returning -EINVAL for an invalid port value.
Addresses clang-scan warnings:
drivers/net/dsa/qca8k.c:1981:3: warning: 2nd function call argument is an
uninitialized value [core.CallAndMessage]
drivers/net/dsa/qca8k.c:1999:9: warning: 2nd function call argument is an
uninitialized value [core.CallAndMessage]
Fixes: 7544b3ff74 ("net: dsa: qca8k: move pcs configuration")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220224220557.147075-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean suggests that sja1105 can support switching between
SGMII and 2500BASE-X modes. Augment sja1105_phylink_get_caps() to
fill in both interface modes if they can be supported.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the MAC capabilities for the SJA1105 DSA switch using the same
decision making which sja1105_phylink_validate() uses. Remove the now
obsolete sja1105_phylink_validate() implementation to allow DSA to use
phylink_generic_validate() for this switch driver.
As noted by Vladimir, this fixes an inconsequential bug which allowed
gigabit and lower interface modes to be indicated when operating in
2500base-X mode.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 DSA driver does not have a phylink_mac_config() method
implementation, it is safe to mark this as a non-legacy driver.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the PCS selection to use mac_select_pcs, which allows the PCS
to perform any validation it needs, and removes the need to set the PCS
in the mac_config() callback, delving into the higher DSA levels to do
so.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the supported interfaces bitmap is populated, phylink will itself
check that the interface mode is present in this bitmap. Drivers no
longer need to perform this check themselves. Remove these checks.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces bitmap for the SJA1105 DSA switch.
This switch only supports a static model of configuration, so we
restrict the interface modes to the configured setting.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Vladimir Oltean <vladimir. │
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the logic in the Felix DSA driver and Ocelot switch library.
For Ocelot switches, the DEST_IDX that is the output of the MAC table
lookup is a logical port (equal to physical port, if no LAG is used, or
a dynamically allocated number otherwise). The allocation we have in
place for LAG IDs is different from DSA's, so we can't use that:
- DSA allocates a continuous range of LAG IDs starting from 1
- Ocelot appears to require that physical ports and LAG IDs are in the
same space of [0, num_phys_ports), and additionally, ports that aren't
in a LAG must have physical port id == logical port id
The implication is that an FDB entry towards a LAG might need to be
deleted and reinstalled when the LAG ID changes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The main purpose of this change is to create a data structure for a LAG
as seen by DSA. This is similar to what we have for bridging - we pass a
copy of this structure by value to ->port_lag_join and ->port_lag_leave.
For now we keep the lag_dev, id and a reference count in it. Future
patches will add a list of FDB entries for the LAG (these also need to
be refcounted to work properly).
The LAG structure is created using dsa_port_lag_create() and destroyed
using dsa_port_lag_destroy(), just like we have for bridging.
Because now, the dsa_lag itself is refcounted, we can simplify
dsa_lag_map() and dsa_lag_unmap(). These functions need to keep a LAG in
the dst->lags array only as long as at least one port uses it. The
refcounting logic inside those functions can be removed now - they are
called only when we should perform the operation.
dsa_lag_dev() is renamed to dsa_lag_by_id() and now returns the dsa_lag
structure instead of the lag_dev net_device.
dsa_lag_foreach_port() now takes the dsa_lag structure as argument.
dst->lags holds an array of dsa_lag structures.
dsa_lag_map() now also saves the dsa_lag->id value, so that linear
walking of dst->lags in drivers using dsa_lag_id() is no longer
necessary. They can just look at lag.id.
dsa_port_lag_id_get() is a helper, similar to dsa_port_bridge_num_get(),
which can be used by drivers to get the LAG ID assigned by DSA to a
given port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make the intent of the code more clear by using the dedicated helper for
iterating over the ports of a switch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DSA LAG API will be changed to become more similar with the bridge
data structures, where struct dsa_bridge holds an unsigned int num,
which is generated by DSA and is one-based. We have a similar thing
going with the DSA LAG, except that isn't stored anywhere, it is
calculated dynamically by dsa_lag_id() by iterating through dst->lags.
The idea of encoding an invalid (or not requested) LAG ID as zero for
the purpose of simplifying checks in drivers means that the LAG IDs
passed by DSA to drivers need to be one-based too. So back-and-forth
conversion is needed when indexing the dst->lags array, as well as in
drivers which assume a zero-based index.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of converting struct net_device *dp->lag_dev into a
struct dsa_lag *dp->lag, we need to rename, for consistency purposes,
all occurrences of the "lag" variable in qca8k to "lag_dev".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of converting struct net_device *dp->lag_dev into a
struct dsa_lag *dp->lag, we need to rename, for consistency purposes,
all occurrences of the "lag" variable in mv88e6xxx to "lag_dev".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Supporting bridge ports in locked mode using the drop on lock
feature in Marvell mv88e6xxx switchcores is described in the
'88E6096/88E6097/88E6097F Datasheet', sections 4.4.6, 4.4.7 and
5.1.2.1 (Drop on Lock).
This feature is implemented here facilitated by the locked port flag.
Signed-off-by: Hans Schultz <schultz.hans+netdev@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek switches in the rtl8365mb family can access the PHY registers of
the internal PHYs via the switch registers. This method is called
indirect access. At a high level, the indirect PHY register access
method involves reading and writing some special switch registers in a
particular sequence. This works for both SMI and MDIO connected
switches.
Currently the rtl8365mb driver does not take any care to serialize the
aforementioned access to the switch registers. In particular, it is
permitted for other driver code to access other switch registers while
the indirect PHY register access is ongoing. Locking is only done at the
regmap level. This, however, is a bug: concurrent register access, even
to unrelated switch registers, risks corrupting the PHY register value
read back via the indirect access method described above.
Arınç reported that the switch sometimes returns nonsense data when
reading the PHY registers. In particular, a value of 0 causes the
kernel's PHY subsystem to think that the link is down, but since most
reads return correct data, the link then flip-flops between up and down
over a period of time.
The aforementioned bug can be readily observed by:
1. Enabling ftrace events for regmap and mdio
2. Polling BSMR PHY register for a connected port;
it should always read the same (e.g. 0x79ed)
3. Wait for step 2 to give a different value
Example command for step 2:
while true; do phytool read swp2/2/0x01; done
On my i.MX8MM, the above steps will yield a bogus value for the BSMR PHY
register within a matter of seconds. The interleaved register access it
then evident in the trace log:
kworker/3:4-70 [003] ....... 1927.139849: regmap_reg_write: ethernet-switch reg=1004 val=bd
phytool-16816 [002] ....... 1927.139979: regmap_reg_read: ethernet-switch reg=1f01 val=0
kworker/3:4-70 [003] ....... 1927.140381: regmap_reg_read: ethernet-switch reg=1005 val=0
phytool-16816 [002] ....... 1927.140468: regmap_reg_read: ethernet-switch reg=1d15 val=a69
kworker/3:4-70 [003] ....... 1927.140864: regmap_reg_read: ethernet-switch reg=1003 val=0
phytool-16816 [002] ....... 1927.140955: regmap_reg_write: ethernet-switch reg=1f02 val=2041
kworker/3:4-70 [003] ....... 1927.141390: regmap_reg_read: ethernet-switch reg=1002 val=0
phytool-16816 [002] ....... 1927.141479: regmap_reg_write: ethernet-switch reg=1f00 val=1
kworker/3:4-70 [003] ....... 1927.142311: regmap_reg_write: ethernet-switch reg=1004 val=be
phytool-16816 [002] ....... 1927.142410: regmap_reg_read: ethernet-switch reg=1f01 val=0
kworker/3:4-70 [003] ....... 1927.142534: regmap_reg_read: ethernet-switch reg=1005 val=0
phytool-16816 [002] ....... 1927.142618: regmap_reg_read: ethernet-switch reg=1f04 val=0
phytool-16816 [002] ....... 1927.142641: mdio_access: SMI-0 read phy:0x02 reg:0x01 val:0x0000 <- ?!
kworker/3:4-70 [003] ....... 1927.143037: regmap_reg_read: ethernet-switch reg=1001 val=0
kworker/3:4-70 [003] ....... 1927.143133: regmap_reg_read: ethernet-switch reg=1000 val=2d89
kworker/3:4-70 [003] ....... 1927.143213: regmap_reg_write: ethernet-switch reg=1004 val=be
kworker/3:4-70 [003] ....... 1927.143291: regmap_reg_read: ethernet-switch reg=1005 val=0
kworker/3:4-70 [003] ....... 1927.143368: regmap_reg_read: ethernet-switch reg=1003 val=0
kworker/3:4-70 [003] ....... 1927.143443: regmap_reg_read: ethernet-switch reg=1002 val=6
The kworker here is polling MIB counters for stats, as evidenced by the
register 0x1004 that we are writing to (RTL8365MB_MIB_ADDRESS_REG). This
polling is performed every 3 seconds, but is just one example of such
unsynchronized access. In Arınç's case, the driver was not using the
switch IRQ, so the PHY subsystem was itself doing polling analogous to
phytool in the above example.
A test module was created [see second Link] to simulate such spurious
switch register accesses while performing indirect PHY register reads
and writes. Realtek was also consulted to confirm whether this is a
known issue or not. The conclusion of these lines of inquiry is as
follows:
1. Reading of PHY registers via indirect access will be aborted if,
after executing the read operation (via a write to the
INDIRECT_ACCESS_CTRL_REG), any register is accessed, other than
INDIRECT_ACCESS_STATUS_REG.
2. The PHY register indirect read is only complete when
INDIRECT_ACCESS_STATUS_REG reads zero.
3. The INDIRECT_ACCESS_DATA_REG, which is read to get the result of the
PHY read, will contain the result of the last successful read
operation. If there was spurious register access and the indirect
read was aborted, then this register is not guaranteed to hold
anything meaningful and the PHY read will silently fail.
4. PHY writes do not appear to be affected by this mechanism.
5. Other similar access routines, such as for MIB counters, although
similar to the PHY indirect access method, are actually table access.
Table access is not affected by spurious reads or writes of other
registers. However, concurrent table access is not allowed. Currently
this is protected via mib_lock, so there is nothing to fix.
The above statements are corroborated both via the test module and
through consultation with Realtek. In particular, Realtek states that
this is simply a property of the hardware design and is not a hardware
bug.
To fix this problem, one must guard against regmap access while the
PHY indirect register read is executing. Fix this by using the newly
introduced "nolock" regmap in all PHY-related functions, and by aquiring
the regmap mutex at the top level of the PHY register access callbacks.
Although no issue has been observed with PHY register _writes_, this
change also serializes the indirect access method there. This is done
purely as a matter of convenience and for reasons of symmetry.
Fixes: 4af2950c50 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Link: https://lore.kernel.org/netdev/CAJq09z5FCgG-+jVT7uxh1a-0CiiFsoKoHYsAWJtiKwv7LXKofQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/871qzwjmtv.fsf@bang-olufsen.dk/
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reported-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no way for Realtek DSA subdrivers to serialize
consecutive regmap accesses. In preparation for a bugfix relating to
indirect PHY register access - which involves a series of regmap
reads and writes - add a facility for subdrivers to serialize their
regmap access.
Specifically, a mutex is added to the driver private data structure and
the standard regmap is initialized with custom lock/unlock ops which use
this mutex. Then, a "nolock" variant of the regmap is added, which is
functionally equivalent to the existing regmap except that regmap
locking is disabled. Functions that wish to serialize a sequence of
regmap accesses may then lock the newly introduced driver-owned mutex
before using the nolock regmap.
Doing things this way means that subdriver code that doesn't care about
serialized register access - i.e. the vast majority of code - needn't
worry about synchronizing register access with an external lock: it can
just continue to use the original regmap.
Another advantage of this design is that, while regmaps with locking
disabled do not expose a debugfs interface for obvious reasons, there
still exists the original regmap which does expose this interface. This
interface remains safe to use even combined with driver codepaths that
use the nolock regmap, because said codepaths will use the same mutex
to synchronize access.
With respect to disadvantages, it can be argued that having
near-duplicate regmaps is confusing. However, the naming is rather
explicit, and examples will abound.
Finally, while we are at it, rename realtek_smi_mdio_regmap_config to
realtek_smi_regmap_config. This makes it consistent with the naming
realtek_mdio_regmap_config in realtek-mdio.c.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The B53 driver does not make use of the speed, duplex, pause or
advertisement in its phylink_mac_config() implementation, so it can be
marked as a non-legacy driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the Broadcom b53 driver to using the phylink_generic_validate()
implementation by removing its own .phylink_validate method and
associated code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a better method to select SFP interface modes, we
no longer need to use phylink_helper_basex_speed() in a driver's
validation function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the Broadcom
B53 DSA switches in preparation to using these for the generic
validation functionality.
The interface modes are derived from:
- b53_serdes_phylink_validate()
- SRAB mux configuration
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've stared at this if() statement for a while trying to work out if
it really does correspond with the comment above, and it does seem to.
However, let's make it more readable and phrase it in the same way as
the comment.
Also add a FIXME into the comment - we appear to deny Gigabit modes for
802.3z interface modes, but 802.3z interface modes only operate at
gigabit and above.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 SPI driver already has support for the KSZ8563. The same switch
chip can also be managed via i2c and we have an KSZ9477 I2C driver, but
that one lacks the relevant compatible entry. Add it.
DT bindings already describe this compatible.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide access to HW offloaded packets over stats64 interface.
The rx/tx_bytes values needed some fixing since HW is accounting size of
the Ethernet frame together with FCS.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b3612ccdf2 ("net: dsa: microchip: implement multi-bridge support")
plugged a packet leak between ports that were members of different bridges.
Unfortunately, this broke another use case, namely that of more than two
ports that are members of the same bridge.
After that commit, when a port is added to a bridge, hardware bridging
between other member ports of that bridge will be cleared, preventing
packet exchange between them.
Fix by ensuring that the Port VLAN Membership bitmap includes any existing
ports in the bridge, not just the port being added.
Fixes: b3612ccdf2 ("net: dsa: microchip: implement multi-bridge support")
Signed-off-by: Svenning Sørensen <sss@secomea.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qca8k driver does not make use of the speed, duplex, pause or
advertisement in its phylink_mac_config() implementation, so it can be
marked as a non-legacy driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the PCS configuration to qca8k_pcs_config().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the qca8k driver to use the phylink_pcs support to talk to the
SGMII PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move qca8k_phylink_mac_link_state() to separate the code movement from
code changes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move qca8k_setup() to be later in the file to avoid needing prototypes
for called functions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the master device does VLAN filtering, the IDs used by the switch
must be added for any frames to be received. Do this in the
port_enable() function, and remove them in port_disable().
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220216204818.28746-1-mans@mansr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Historically, the felix DSA driver has installed special traps such that
PTP over L2 works with the ocelot-8021q tagging protocol; commit
0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP
timestamping") has the details.
Then the ocelot switch library also gained more comprehensive support
for PTP traps through commit 96ca08c058 ("net: mscc: ocelot: set up
traps for PTP packets").
Right now, PTP over L2 works using ocelot-8021q via the traps it has set
for itself, but nothing else does. Consolidating the two code blocks
would make ocelot-8021q gain support for PTP over L4 and tc-flower
traps, and at the same time avoid some code and TCAM duplication.
The traps are similar in intent, but different in execution, so some
explanation is required. The traps set up by felix_setup_mmio_filtering()
are VCAP IS1 filters, which have a PAG that chains them to a VCAP IS2
filter, and the IS2 is where the 'trap' action resides. The traps set up
by ocelot_trap_add(), on the other hand, have a single filter, in VCAP
IS2. The reason for chaining VCAP IS1 and IS2 in Felix was to ensure
that the hardcoded traps take precedence and cannot be overridden by the
Ocelot switch library.
So in principle, the PTP traps needed for ocelot-8021q in the Felix
driver can rely on ocelot_trap_add(), but the filters need to be patched
to account for a quirk that LS1028A has: the quirk_no_xtr_irq described
in commit 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP
timestamping"). Live-patching is done by iterating through the trap list
every time we know it has been updated, and transforming a trap into a
redirect + CPU copy if ocelot-8021q is in use.
Making the DSA ocelot-8021q tagger work with the Ocelot traps means we
can eliminate the dedicated OCELOT_VCAP_IS1_TAG_8021Q_PTP_MMIO and
OCELOT_VCAP_IS2_TAG_8021Q_PTP_MMIO cookies. To minimize the patch delta,
OCELOT_VCAP_IS2_MRP_TRAP takes the place of OCELOT_VCAP_IS2_TAG_8021Q_PTP_MMIO
(the alternative would have been to left-shift all cookie numbers by 1).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There has been some controversy related to the sanity check that a CPU
port exists, and commit e8b1d76980 ("net: dsa: felix: Fix memory leak
in felix_setup_mmio_filtering") even "corrected" an apparent memory leak
as static analysis tools see it.
However, the check is completely dead code, since the earliest point at
which felix_setup_mmio_filtering() can be called is:
felix_pci_probe
-> dsa_register_switch
-> dsa_switch_probe
-> dsa_tree_setup
-> dsa_tree_setup_cpu_ports
-> dsa_tree_setup_default_cpu
-> contains the "DSA: tree %d has no CPU port\n" check
-> dsa_tree_setup_master
-> dsa_master_setup
-> sysfs_create_group(&dev->dev.kobj, &dsa_group);
-> makes tagging_store() callable
-> dsa_tree_change_tag_proto
-> dsa_tree_notify
-> dsa_switch_event
-> dsa_switch_change_tag_proto
-> ds->ops->change_tag_protocol
-> felix_change_tag_protocol
-> felix_set_tag_protocol
-> felix_setup_tag_8021q
-> felix_setup_mmio_filtering
-> breaks at first CPU port
So probing would have failed earlier if there wasn't any CPU port
defined.
To avoid all confusion, delete the dead code and replace it with a
comment.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the helpers that avoid the quadratic complexity associated with
calling dsa_to_port() indirectly: dsa_is_unused_port(),
dsa_is_cpu_port().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every use case that needed VCAP filters (in order: DSA tag_8021q, MRP,
PTP traps) has hardcoded filter identifiers that worked well enough for
that use case alone. But when two or more of those use cases would be
used together, some of those identifiers would overlap, leading to
breakage.
Add definitions for each cookie and centralize them in ocelot_vcap.h,
such that the overlaps are more obvious.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put(priv->ds->slave_mii_bus->dev.of_node) should be
done before mdiobus_free(priv->ds->slave_mii_bus).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 0d120dfb5d ("net: dsa: lantiq_gswip: don't use devres for mdiobus")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1644921768-26477-1-git-send-email-khoroshilov@ispras.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These chips have 8 built-in FE PHYs and 3 SERDES interfaces that can
run at 1G. With the blamed commit, the built-in PHYs could no longer
be connected to, using an MII PHY interface mode.
Create a separate .phylink_get_caps callback for these chips, which
takes the FE/GE split into consideration.
Fixes: 2ee84cfefb ("net: dsa: mv88e6xxx: convert to phylink_generic_validate()")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20220213185154.3262207-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some devices, like the switch in Banana Pi BPI R64 only starts to answer
after a HW reset. It is the same reset code from realtek-smi.
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reset GPIO was missing, the driver was still printing an info
message and still trying to assert the reset. Although gpiod_set_value()
will silently ignore calls with NULL gpio_desc, it is better to make it
clear the driver might allow gpio_desc to be NULL.
The initial value for the reset pin was changed to GPIOD_OUT_LOW,
followed by a gpiod_set_value() asserting the reset. This way, it will
be easier to spot if and where the reset really happens.
A new "asserted RESET" message was added just after the reset is
asserted, similar to the existing "deasserted RESET" message. Both
messages were demoted to dbg. The code comment is not needed anymore.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx is special among DSA drivers in that it requires the VTU to
contain the VID of the FDB entry it modifies in
mv88e6xxx_port_db_load_purge(), otherwise it will return -EOPNOTSUPP.
Sometimes due to races this is not always satisfied even if external
code does everything right (first deletes the FDB entries, then the
VLAN), because DSA commits to hardware FDB entries asynchronously since
commit c9eb3e0f87 ("net: dsa: Add support for learning FDB through
notification").
Therefore, the mv88e6xxx driver must close this race condition by
itself, by asking DSA to flush the switchdev workqueue of any FDB
deletions in progress, prior to exiting a VLAN.
Fixes: c9eb3e0f87 ("net: dsa: Add support for learning FDB through notification")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset input to the LAN9303 chip is active low, and devicetree
gpio handles reflect this. Therefore, the gpio should be requested
with an initial state of high in order for the reset signal to be
asserted. Other uses of the gpio already use the correct polarity.
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fianelil <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220209145454.19749-1-mans@mansr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mv88e6352, mv88e6240 and mv88e6176 have a serdes interface. This patch
allows to configure the output swing to a desired value in the
phy-handle of the port. The value which is peak to peak has to be
specified in microvolts. As the chips only supports eight dedicated
values we return EINVAL if the value in the DTS does not match one of
these values.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since struct mv88e6xxx_mdio_bus *mdio_bus is the bus->priv of something
allocated with mdiobus_alloc_size(), this means that mdiobus_free(bus)
will free the memory backing the mdio_bus as well. Therefore, the
mdio_bus->list element is freed memory, but we continue to iterate
through the list of MDIO buses using that list element.
To fix this, use the proper list iterator that handles element deletion
by keeping a copy of the list element next pointer.
Fixes: f53a2ce893 ("net: dsa: mv88e6xxx: don't use devres for mdiobus")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220210174017.3271099-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/dsa/qca8k.c:422:37-43: ERROR: application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer
Generated by: scripts/coccinelle/misc/noderef.cocci
Fixes: 90386223f4 ("net: dsa: qca8k: add support for larger read/write size with mgmt Ethernet")
CC: Ansuel Smith <ansuelsmth@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220209221304.GA17529@d2214a582157
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The GSWIP switch is a platform device, so the initial set of constraints
that I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the GSWIP switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The gswip driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nobody in this driver calls mdiobus_unregister(), which is necessary if
mdiobus_register() completes successfully. So if the devres callbacks
that free the mdiobus get invoked (this is the case when unbinding the
driver), mdiobus_free() will BUG if the mdiobus is still registered,
which it is.
My speculation is that this is due to the fact that prior to commit
ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
from June 2020, _devm_mdiobus_free() used to call mdiobus_unregister().
But at the time that the mt7530 support was introduced in May 2021, the
API was already changed. It's therefore likely that the blamed patch was
developed on an older tree, and incorrectly adapted to net-next. This
makes the Fixes: tag correct.
Fix the problem by using the devres variant of mdiobus_register.
Fixes: ba751e28d4 ("net: dsa: mt7530: add interrupt support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Seville VSC9959 switch is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the seville switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The seville driver has a code structure that could accommodate both the
mdiobus_unregister and mdiobus_free calls, but it has an external
dependency upon mscc_miim_setup() from mdio-mscc-miim.c, which calls
devm_mdiobus_alloc_size() on its behalf. So rather than restructuring
that, and exporting yet one more symbol mscc_miim_teardown(), let's work
with devres and replace of_mdiobus_register with the devres variant.
When we use all-devres, we can ensure that devres doesn't free a
still-registered bus (it either runs both callbacks, or none).
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Felix VSC9959 switch is a PCI device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the felix switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The felix driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc_size() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Starfighter 2 is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the bcm_sf2 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The bcm_sf2 driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The ar9331 is an MDIO device, so the initial set of constraints that I
thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the ar9331 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The ar9331 driver doesn't have a complex code structure for mdiobus
removal, so just replace of_mdiobus_register with the devres variant in
order to be all-devres and ensure that we don't free a still-registered
bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The mv88e6xxx is an MDIO device, so the initial set of constraints that
I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the Marvell switch driver on shutdown.
systemd-shutdown[1]: Powering off.
mv88e6085 0x0000000008b96000:00 sw_gl0: Link is Down
fsl-mc dpbp.9: Removing from iommu group 7
fsl-mc dpbp.8: Removing from iommu group 7
------------[ cut here ]------------
kernel BUG at drivers/net/phy/mdio_bus.c:677!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00040-gdc05f73788e5 #15
pc : mdiobus_free+0x44/0x50
lr : devm_mdiobus_free+0x10/0x20
Call trace:
mdiobus_free+0x44/0x50
devm_mdiobus_free+0x10/0x20
devres_release_all+0xa0/0x100
__device_release_driver+0x190/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x4c/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x94/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_device_remove+0x24/0x40
__fsl_mc_device_remove+0xc/0x20
device_for_each_child+0x58/0xa0
dprc_remove+0x90/0xb0
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_bus_remove+0x80/0x100
fsl_mc_bus_shutdown+0xc/0x1c
platform_shutdown+0x20/0x30
device_shutdown+0x154/0x330
kernel_power_off+0x34/0x6c
__do_sys_reboot+0x15c/0x250
__arm64_sys_reboot+0x20/0x30
invoke_syscall.constprop.0+0x4c/0xe0
do_el0_svc+0x4c/0x150
el0_svc+0x24/0xb0
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x178/0x17c
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The Marvell driver already has a good structure for mdiobus removal, so
just plug in mdiobus_free and get rid of devres.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Rafael Richter <Rafael.Richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Call mv88e6xxx_reg_unlock(chip) before returning on this error path.
Fixes: 7af4a361a6 ("net: dsa: mv88e6xxx: Improve isolation of standalone ports")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The <= ARRAY_SIZE() needs to be < ARRAY_SIZE() to prevent an out of
bounds error.
Fixes: d4ebf12bce ("net: dsa: mv88e6xxx: populate supported_interfaces and mac_capabilities")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We generally default the vendor to y and the drivers itself
to n. NET_DSA_REALTEK, however, selects a whole bunch of things,
so it's not a pure "vendor selection" knob. Let's default it all
to n.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a copy and paste bug. It was supposed to check "clear_skb"
instead of "write_skb".
Fixes: 2cd5485663 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the Realtek
rtl8365 DSA switch and remove the old validate implementation to allow
DSA to use phylink_generic_validate() for this switch driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The decision whether to report serdes statistics currently depends on
the cached C_Mode value for the port, read at probe time or updated by
configuration. However, port 4 can be in "automedia" mode when it is
used as a serdes port, meaning it switches between the internal PHY and
the serdes, changing the read-only C_Mode value depending on which
first gains link. Consequently, the C_Mode value read at probe does not
accurately reflect whether the port has the serdes associated with it.
In "net: dsa: mv88e6xxx: add mv88e6352_g2_scratch_port_has_serdes()",
we added a way to read the hardware configuration to determine which
port has the serdes associated with it. Use this to determine which
port reports the serdes statistics.
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the mv88e6xxx chip drivers are supplying the supported
interfaces and MAC capabilities, switch the driver to use the generic
phylink validation implementation by removing our own validation
implementations. This causes DSA to call phylink_generic_validate()
on our behalf.
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the
Marvell MV88E6xxx DSA switches in preparation to using these for the
validation functionality.
Patch co-authored by Marek.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org> [ fixed 6341 and 6393x ]
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the hardware configuration to determine which port is attached
to the serdes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given that standalone ports are now configured to bypass the ATU and
forward all frames towards the upstream port, extend the ATU bypass to
multichip systems.
Load VID 0 (standalone) into the VTU with the policy bit set. Since
VID 4095 (bridged) is already loaded, we now know that all VIDs in use
are always available in all VTUs. Therefore, we can safely enable
802.1Q on DSA ports.
Setting the DSA ports' VTU policy to TRAP means that all incoming
frames on VID 0 will be classified as MGMT - as a result, the ATU is
bypassed on all subsequent switches.
With this isolation in place, we are able to support configurations
that are simultaneously very quirky and very useful. Quirky because it
involves looping cables between local switchports like in this
example:
CPU
| .------.
.---0---. | .----0----.
| sw0 | | | sw1 |
'-1-2-3-' | '-1-2-3-4-'
$ @ '---' $ @ % %
We have three physically looped pairs ($, @, and %).
This is very useful because it allows us to run the kernel's
kselftests for the bridge on mv88e6xxx hardware.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip has support for the same per-port policy actions found in
later versions of LinkStreet devices.
Fixes: f3a2cd326e ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A VTU entry with policy enabled is used in combination with a port's
VTU policy setting to override normal switching behavior for frames
assigned to the entry's VID.
A typical example is to Treat all frames in a particular VLAN as
control traffic, and trap them to the CPU. In which case the relevant
user port's VTU policy would be set to TRAP.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear MapDA on standalone ports to bypass any ATU lookup that might
point the packet in the wrong direction. This means that all packets
are flooded using the PVT config. So make sure that standalone ports
are only allowed to communicate with the local upstream port.
Here is a scenario in which this is needed:
CPU
| .----.
.---0---. | .--0--.
| sw0 | | | sw1 |
'-1-2-3-' | '-1-2-'
'---'
- sw0p1 and sw1p1 are bridged
- sw0p2 and sw1p2 are in standalone mode
- Learning must be enabled on sw0p3 in order for hardware forwarding
to work properly between bridged ports
1. A packet with SA :aa comes in on sw1p2
1a. Egresses sw1p0
1b. Ingresses sw0p3, ATU adds an entry for :aa towards port 3
1c. Egresses sw0p0
2. A packet with DA :aa comes in on sw0p2
2a. If an ATU lookup is done at this point, the packet will be
incorrectly forwarded towards sw0p3. With this change in place,
the ATU is bypassed and the packet is forwarded in accordance
with the PVT, which only contains the CPU port.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the xrs700x
family of DSA switches and remove the old validate implementation to
allow DSA to use phylink_generic_validate() for this switch driver.
According to commit ee00b24f32 ("net: dsa: add Arrow SpeedChips
XRS700x driver") the switch supports one RMII port and up to three
RGMII ports. This commit assumes that port 0 is the RMII port and the
remainder are RGMII.
This commit also results in the Autoneg bit being set in the ethtool
link modes, which wasn't in the original; if this switch supports
RGMII to a 10/100/1G PHY, then surely we want to allow Autoneg on the
PHY.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the QCA8K
DSA switch and remove the old validate implementation to allow DSA to
use phylink_generic_validate() for this switch driver.
In making this change, we bring consistency to the ethtool linkmodes
that phylink's validate step produces, thereby following the expected
behaviour as the phylink documentation has explained. Specifically, the
ethtool 1000baseX_Full capability is now permitted for all interface
modes, as it is a property of the PHY driver whether 1000baseX fiber
connections can be supported.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the
Microchip KSZ8795 DSA switch and remove the old validate implementation
to allow DSA to use phylink_generic_validate() for this switch driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the bcm_sf2
DSA switch and remove the old validate implementation to allow DSA to
use phylink_generic_validate() for this switch driver.
The exclusion of Gigabit linkmodes for MII and Reverse MII links is
handled within phylink_generic_validate() in phylink, so there is no
need to make them conditional on the interface mode in the driver.
Thanks to Florian Fainelli for suggesting how to populate the supported
interfaces.
Link: https://lore.kernel.org/r/3b3fed98-0c82-99e9-dc72-09fe01c2bcf3@gmail.com
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the AR9331
DSA switch and remove the old validate implementation to allow DSA to
use phylink_generic_validate() for this switch driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce qca8k_bulk_read/write() function to use mgmt Ethernet way to
read/write packet in bulk. Make use of this new function in the fdb
function and while at it reduce the reg for fdb_read from 4 to 3 as the
max bit for the ARL(fdb) table is 83 bits.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mgmt Ethernet packet can read/write up to 16byte at times. The len reg
is limited to 15 (0xf). The switch actually sends and accepts data in 4
different steps of len values.
Len steps:
- 0: nothing
- 1-4: first 4 byte
- 5-6: first 12 byte
- 7-15: all 16 byte
In the alloc skb function we check if the len is 16 and we fix it to a
len of 15. It the read/write function interest to extract the real asked
data. The tagger handler will always copy the fully 16byte with a READ
command. This is useful for some big regs like the fdb reg that are
more than 4byte of data. This permits to introduce a bulk function that
will send and request the entire entry in one go.
Write function is changed and it does now require to pass the pointer to
val to also handle array val.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From Documentation, we can cache lo and hi the same way we do with the
page. This massively reduce the mdio write as 3/4 of the time as we only
require to write the lo or hi part for a mdio write.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There can be multiple qca8k switch on the same system. Move the static
qca8k_current_page to qca8k_priv and make it specific for each switch.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use mgmt Ethernet also for phy read/write if availabale. Use a different
seq number to make sure we receive the correct packet.
On any error, we fallback to the legacy mdio read/write.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch can autocast MIB counter using Ethernet packet.
Add support for this and provide a handler for the tagger.
The switch will send packet with MIB counter for each port, the switch
will use completion API to wait for the correct packet to be received
and will complete the task only when each packet is received.
Although the handler will drop all the other packet, we still have to
consume each MIB packet to complete the request. This is done to prevent
mixed data with concurrent ethtool request.
connect_tag_protocol() is used to add the handler to the tag_qca tagger,
master_state_change() use the MIB lock to make sure no MIB Ethernet is
in progress.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add qca8k side support for mgmt read/write in Ethernet packet.
qca8k supports some specially crafted Ethernet packet that can be used
for mgmt read/write instead of the legacy method uart/internal mdio.
This add support for the qca8k side to craft the packet and enqueue it.
Each port and the qca8k_priv have a special struct to put data in it.
The completion API is used to wait for the packet to be received back
with the requested data.
The various steps are:
1. Craft the special packet with the qca hdr set to mgmt read/write
mode.
2. Set the lock in the dedicated mgmt struct.
3. Increment the seq number and set it in the mgmt pkt
4. Reinit the completion.
5. Enqueue the packet.
6. Wait the packet to be received.
7. Use the data set by the tagger to complete the mdio operation.
If the completion timeouts or the ack value is not true, the legacy
mdio way is used.
It has to be considered that in the initial setup mdio is still used and
mdio is still used until DSA is ready to accept and tag packet.
tag_proto_connect() is used to fill the required handler for the tagger
to correctly parse and elaborate the special Ethernet mdio packet.
Locking is added to qca8k_master_change() to make sure no mgmt Ethernet
are in progress.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO/MIB Ethernet require the master port and the tagger availabale to
correctly work. Use the new api master_state_change to track when master
is operational or not and set a bool in qca8k_priv.
We cache the first cached master available and we check if other cpu
port are operational when the cached one goes down.
This cached master will later be used by mdio read/write and mib request to
correctly use the working function.
qca8k implementation for MDIO/MIB Ethernet is bad. CPU port0 is the only
one that answers with the ack packet or sends MIB Ethernet packets. For
this reason the master_state_change ignore CPU port6 and only checks
CPU port0 if it's operational and enables this mode.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make MediaTek MT753x DSA driver enable MediaTek Gigabit PHYs driver to
properly control MT7530 and MT7531 switch PHYs.
A noticeable change is that the behaviour of switchport interfaces going
up-down-up-down is no longer there.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220129062703.595-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before this change, both the read and write callback would start out
by asserting that the chip's busy flag was cleared. However, both
callbacks also made sure to wait for the clearing of the busy bit
before returning - making the initial check superfluous. The only
time that would ever have an effect was if the busy bit was initially
set for some reason.
With that in mind, make sure to perform an initial check of the busy
bit, after which both read and write can rely the previous operation
to have waited for the bit to clear.
This cuts the number of operations on the underlying MDIO bus by 25%
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid a long delay when a busy bit is still set and has to be polled
again.
Measurements on a system with 2 Opals (6097F) and one Agate (6352)
show that even with this much tighter loop, we have about a 50% chance
of the bit being cleared on the first poll, all other accesses see the
bit being cleared on the second poll.
On a standard MDIO bus running MDC at 2.5MHz, a single access with 32
bits of preamble plus 32 bits of data takes 64*(1/2.5MHz) = 25.6us.
This means that mv88e6xxx_smi_direct_wait took 26us + CPU overhead in
the fast scenario, but 26us + 1500us + 26us + CPU overhead in the slow
case - bringing the average close to 1ms.
With this change in place, the slow case is closer to 2*26us + CPU
overhead, with the average well below 100us - a 10x improvement.
This translates to real-world winnings. On a 3-chip 20-port system,
the modprobe time drops by 88%:
Before:
root@coronet:~# time modprobe mv88e6xxx
real 0m 15.99s
user 0m 0.00s
sys 0m 1.52s
After:
root@coronet:~# time modprobe mv88e6xxx
real 0m 2.21s
user 0m 0.00s
sys 0m 1.54s
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trap door number is a 4-bit number divided in two regions (3 and 1-bit).
Both values were not masked properly. This bug does not affect supported
devices as they use up to port 7 (ext2). It would only be a problem if
the driver becomes compatible with 10-port switches like RTL8370MB and
RTL8310SR.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
External interfaces can be configured, even if they are not CPU ports.
The first CPU port will also be the trap port (for receiving trapped
frames from the switch).
The CPU information was dropped from chip data as it was not used
outside setup. The only other place it was used is when it wrongly
checks for CPU port when it should check for extint.
The supported modes check now uses port type and not port usage.
As a byproduct, more than one CPU can be configured. although this
might not work well with DSA setups. Also, this driver is still only
blindly forwarding all traffic to CPU port(s).
This change was not tested in a device with multiple active external
interfaces ports.
realtek_priv->cpu_port is now only used by rtl8366rb.c
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8367RB-VB is a 5+2 port 10/100/1000M Ethernet switch.
It is similar to RTL8367S but in this version, both
external interfaces are RGMII.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek's RTL8367S, a 5+2 port 10/100/1000M Ethernet switch.
It shares the same driver family (RTL8367C) with other models
as the RTL8365MB-VC. Its compatible string is "realtek,rtl8367s".
It was tested only with MDIO interface (realtek-mdio), although it might
work out-of-the-box with SMI interface (using realtek-smi).
This patch was based on an unpublished patch from Alvin Šipraga
<alsi@bang-olufsen.dk>.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of a fixed CPU port, assume that DSA is correct.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"extport" 0, 1, 2 was used to reference external ports id (ext0, ext1,
ext2). Meanwhile, port 0..9 is used as switch ports, including external
ports. "extport" was renamed to extint to make it clear it does not mean
the port number but the external interface number id.
The macros that map extint numbers to registers addresses now use inline
ifs instead of binary arithmetic.
Realtek uses in docs and drivers EXT_PORT0 (GMAC1) and EXT_PORT1
(GMAC2), with EXT_PORT0 being converted to ext_id == 1 and so on. It
might introduce some confusing while reading datasheets but it will not
be exposed to users.
"extint" was hardcoded to 1. However, some chips have multiple external
interfaces. It's not right to assume the CPU port uses extint 1 nor that
all extint are CPU ports. Now it came from a map between port number and
external interface id number.
This patch still does not allow multiple CPU ports nor extint as a non
CPU port.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is a mdio_driver instead of a platform driver (like
realtek-smi).
ds_ops was duplicated for smi and mdio usage as mdio interfaces uses
phy_{read,write} in ds_ops and the presence of phy_read is incompatible
with external slave_mii_bus allocation.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparing for multiple interfaces support, the drivers
must be independent of realtek-smi.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the only two direct calls from subdrivers to realtek-smi.
Now they are called from realtek_priv. Subdrivers can now be
linked independently from realtek-smi.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to adding other interfaces, the private data structure
was renamed to priv. Also, realtek_smi_variant and realtek_smi_ops
were renamed to realtek_variant and realtek_ops as those structs are
not SMI specific.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed kdoc mark for incomplete struct description.
Added a return description for rtl8366rb_drop_untagged.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new microchip,synclko-disable property which can be specified
to disable the reference clock output from the device if not required
by the board design.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 2nd param of phy_init_eee(): clk_stop_enable is a bool param, use
true or false instead of 1/0.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220123152241.1480-1-jszhang@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for flushing the MAC table on a given port in the ocelot
switch library, and use this functionality in the felix DSA driver.
This operation is needed when a port leaves a bridge to become
standalone, and when the learning is disabled, and when the STP state
changes to a state where no FDB entry should be present.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220107144229.244584-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A simple variable update from "pcs" to "mdio_device" for the mdio device
will make things a little cleaner.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple rename of a variable to make things more logical.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove references to lynx_pcs structures so drivers like the Felix DSA
can reference alternate PCS drivers.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Define more regs. Some switches (e.g. BCM4908) have up to 6 regs.
2. Add helper for handling non-lineral port <-> reg mappings.
3. Add support for 12 B LED reg blocks on BCM4908 (different layout)
Complete support for LEDs setup will be implemented once Linux receives
a proper design & implementation for "hardware" LEDs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211229171642.22942-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sock.h is pretty heavily used (5k objects rebuilt on x86 after
it's touched). We can drop the include of filter.h from it and
add a forward declaration of struct sk_filter instead.
This decreases the number of rebuilt objects when bpf.h
is touched from ~5k to ~1k.
There's a lot of missing includes this was masking. Primarily
in networking tho, this time.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/bpf/20211229004913.513372-1-kuba@kernel.org
Add index to flow_action_entry structure and delete index from police and
gate child structure.
We make this change to offload tc action for driver to identify a tc
action.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded variable used to store return value.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Debug print uses invalid check to detect if speed is unforced:
(speed != SPEED_UNFORCED) should be used instead of (!speed).
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Andrey Eremeev <Axtone4all@yandex.ru>
Fixes: 96a2b40c7b ("net: dsa: mv88e6xxx: add port's MAC speed setter")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent net-next fails to initialize ports with:
realtek-smi switch: phy mode gmii is unsupported on port 0
realtek-smi switch lan5 (uninitialized): validation of gmii with
support 0000000,00000000,000062ef and advertisement
0000000,00000000,000062ef failed: -22
realtek-smi switch lan5 (uninitialized): failed to connect to PHY:
-EINVAL
realtek-smi switch lan5 (uninitialized): error -22 setting up PHY
for tree 1, switch 0, port 0
Current net branch(3dd7d40b43) is not
affected.
I also noticed the same issue before with older versions but using
a MDIO interface driver, not realtek-smi.
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports PTP for UDP transport too. Therefore, add the missing static
FDB entries to ensure correct forwarding of these packets.
Fixes: ddd56dfe52 ("net: dsa: hellcreek: Add PTP clock support")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow PTP peer delay measurements on blocked ports by STP. In case of topology
changes the PTP stack can directly start with the correct delays.
Fixes: ddd56dfe52 ("net: dsa: hellcreek: Add PTP clock support")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Treat STP as management traffic. STP traffic is designated for the CPU port
only. In addition, STP traffic has to pass blocked ports.
Fixes: e4b27ebc78 ("net: dsa: Add DSA driver for Hirschmann Hellcreek switches")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The insertion of static FDB entries ignores the pass_blocked bit. That bit is
evaluated with regards to STP. Add the missing functionality.
Fixes: e4b27ebc78 ("net: dsa: Add DSA driver for Hirschmann Hellcreek switches")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver was incorrectly converted assuming that "sja1105" is the only
tagger supported by this driver. This results in SJA1110 switches
failing to probe:
sja1105 spi1.0: Unable to connect to tag protocol "sja1110": -EPROTONOSUPPORT
sja1105: probe of spi1.2 failed with error -93
Add DSA_TAG_PROTO_SJA1110 to the list of supported taggers by the
sja1105 driver. The sja1105_tagger_data structure format is common for
the two tagging protocols.
Fixes: c79e84866d ("net: dsa: tag_sja1105: convert to tagger-owned data")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 94dd016ae5 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 64d47d50be ("net: dsa: mv88e6xxx: configure interface settings
in mac_config") removed forcing of speed and duplex from
mv88e6xxx_mac_config(), where the link is forced down, and left it only
in mv88e6xxx_mac_link_up(), by which time link is unforced.
It seems that (at least on 88E6190) when changing cmode to 2500base-x,
if the link is not forced down, but the speed or duplex are still
forced, the forcing of new settings for speed & duplex doesn't take in
mv88e6xxx_mac_link_up().
Fix this by unforcing speed & duplex in mv88e6xxx_mac_link_down().
Fixes: 64d47d50be ("net: dsa: mv88e6xxx: configure interface settings in mac_config")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver messes with the tagging protocol's state when PTP RX
timestamping is enabled/disabled. This is fundamentally necessary
because the tagger needs to know what to do when it receives a PTP
packet. If RX timestamping is enabled, then a metadata follow-up frame
is expected, and this holds the (partial) timestamp. So the tagger plays
hide-and-seek with the network stack until it also gets the metadata
frame, and then presents a single packet, the timestamped PTP packet.
But when RX timestamping isn't enabled, there is no metadata frame
expected, so the hide-and-seek game must be turned off and the packet
must be delivered right away to the network stack.
Considering this, we create a pseudo isolation by devising two tagger
methods callable by the switch: one to get the RX timestamping state,
and one to set it. Since we can't export symbols between the tagger and
the switch driver, these methods are exposed through function pointers.
After this change, the public portion of the sja1105_tagger_data
contains only function pointers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6d709cadfd.
The above change was done to avoid calling symbols exported by the
switch driver from the tagging protocol driver.
With the tagger-owned storage model, we have a new option on our hands,
and that is for the switch driver to provide a data consumer handler in
the form of a function pointer inside the ->connect_tag_protocol()
method. Having a function pointer avoids the problems of the exported
symbols approach.
By creating a handler for metadata frames holding TX timestamps on
SJA1110, we are able to eliminate an skb queue from the tagger data, and
replace it with a simple, and stateless, function pointer. This skb
queue is now handled exclusively by sja1105_ptp.c, which makes the code
easier to follow, as it used to be before the reverted patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, struct sja1105_tagger_data is a part of struct
sja1105_private, and is used by the sja1105 driver to populate dp->priv.
With the movement towards tagger-owned storage, the sja1105 driver
should not be the owner of this memory.
This change implements the connection between the sja1105 switch driver
and its tagging protocol, which means that sja1105_tagger_data no longer
stays in dp->priv but in ds->tagger_data, and that the sja1105 driver
now only populates the sja1105_port_deferred_xmit callback pointer.
The kthread worker is now the responsibility of the tagger.
The sja1105 driver also alters the tagger's state some more, especially
with regard to the PTP RX timestamping state. This will be fixed up a
bit in further changes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX timestamp ID is incremented by the SJA1110 PTP timestamping
callback (->port_tx_timestamp) for every packet, when cloning it.
It isn't used by the tagger at all, even though it sits inside the
struct sja1105_tagger_data.
Also, serialization to this structure is currently done through
tagger_data->meta_lock, which is a cheap hack because the meta_lock
isn't used for anything else on SJA1110 (sja1105_rcv_meta_state_machine
isn't called).
This change moves ts_id from sja1105_tagger_data to sja1105_private and
introduces a dedicated spinlock for it, also in sja1105_private.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The design of the sja1105 tagger dp->priv is that each port has a
separate struct sja1105_port, and the sp->data pointer points to a
common struct sja1105_tagger_data.
We have removed all per-port members accessible by the tagger, and now
only struct sja1105_tagger_data remains. Make dp->priv point directly to
this.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tagger property is in fact not used at all by the tagger, only by
the switch driver. Therefore it makes sense to be moved to
sja1105_private.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ocelot-8021q driver was converted to deferred xmit as part of
commit 8d5f7954b7 ("net: dsa: felix: break at first CPU port during
init and teardown"), the deferred implementation was deliberately made
subtly different from what sja1105 has.
The implementation differences lied on the following observations:
- There might be a race between these two lines in tag_sja1105.c:
skb_queue_tail(&sp->xmit_queue, skb_get(skb));
kthread_queue_work(sp->xmit_worker, &sp->xmit_work);
and the skb dequeue logic in sja1105_port_deferred_xmit(). For
example, the xmit_work might be already queued, however the work item
has just finished walking through the skb queue. Because we don't
check the return code from kthread_queue_work, we don't do anything if
the work item is already queued.
However, nobody will take that skb and send it, at least until the
next timestampable skb is sent. This creates additional (and
avoidable) TX timestamping latency.
To close that race, what the ocelot-8021q driver does is it doesn't
keep a single work item per port, and a skb timestamping queue, but
rather dynamically allocates a work item per packet.
- It is also unnecessary to have more than one kthread that does the
work. So delete the per-port kthread allocations and replace them with
a single kthread which is global to the switch.
This change brings the two implementations in line by applying those
observations to the sja1105 driver as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is not necessary and complicates the conversion of this driver
to tagger-owned memory. If there is a PTP packet that is sent
concurrently with the port getting disabled, the deferred xmit mechanism
is robust enough to time out when it sees that it hasn't been delivered,
and recovers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The felix driver makes very light use of dp->priv, and the tagger is
effectively stateless. dp->priv is practically only needed to set up a
callback to perform deferred xmit of PTP and STP packets using the
ocelot-8021q tagging protocol (the main ocelot tagging protocol makes no
use of dp->priv, although this driver sets up dp->priv irrespective of
actual tagging protocol in use).
struct felix_port (what used to be pointed to by dp->priv) is removed
and replaced with a two-sided structure. The public side of this
structure, visible to the switch driver, is ocelot_8021q_tagger_data.
The private side is ocelot_8021q_tagger_private, and the latter
structure physically encapsulates the former. The public half of the
tagger data structure can be accessed through a helper of the same name
(ocelot_8021q_tagger_data) which also sanity-checks the protocol
currently in use by the switch. The public/private split was requested
by Andrew Lunn.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a typical mv88e6xxx switch tree like this:
CPU
| .----.
.--0--. | .--0--.
| sw0 | | | sw1 |
'-1-2-' | '-1-2-'
'---'
If sw1p{1,2} are added to a bridge that sw0p1 is not a part of, sw0
still needs to add a crosschip PVT entry for the virtual DSA device
assigned to represent the bridge.
Fixes: ce5df6894a ("net: dsa: mv88e6xxx: map virtual bridges with forwarding offload in the PVT")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martyn Welch reports that his CPU port is unable to link where it has
been necessary to use one of the switch ports with an internal PHY for
the CPU port. The reason behind this is the port control register is
left forcing the link down, preventing traffic flow.
This occurs because during initialisation, phylink expects the link to
be down, and DSA forces the link down by synthesising a call to the
DSA drivers phylink_mac_link_down() method, but we don't touch the
forced-link state when we later reconfigure the port.
Resolve this by also unforcing the link state when we are operating in
PHY mode and the PPU is set to poll the PHY to retrieve link status
information.
Reported-by: Martyn Welch <martyn.welch@collabora.com>
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Fixes: 3be98b2d5f ("net: dsa: Down cpu/dsa ports phylink will control")
Cc: <stable@vger.kernel.org> # 5.7: 2b29cb9e3f: net: dsa: mv88e6xxx: fix "don't use PHY_DETECT on internal PHY's"
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1mvFhP-00F8Zb-Ul@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid a memory leak if there is not a CPU port defined.
Fixes: 8d5f7954b7 ("net: dsa: felix: break at first CPU port during init and teardown")
Addresses-Coverity-ID: 1492897 ("Resource leak")
Addresses-Coverity-ID: 1492899 ("Resource leak")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211209110538.11585-1-jose.exposito89@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Added default case to handle undefined cmode scenario in
mv88e6393x_serdes_power() and mv88e6393x_serdes_power() methods.
Addresses-Coverity: 1494644 ("Uninitialized scalar variable")
Fixes: 21635d9203 (net: dsa: mv88e6xxx: Fix application of erratum 4.8 for 88E6393X)
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Ameer Hamza <amhamza.mgc@gmail.com>
Link: https://lore.kernel.org/r/20211209041552.9810-1-amhamza.mgc@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit fixes a misunderstanding in commit 4a3e0aeddf ("net: dsa:
mv88e6xxx: don't use PHY_DETECT on internal PHY's").
For Marvell DSA switches with the PHY_DETECT bit (for non-6250 family
devices), controls whether the PPU polls the PHY to retrieve the link,
speed, duplex and pause status to update the port configuration. This
applies for both internal and external PHYs.
For some switches such as 88E6352 and 88E6390X, PHY_DETECT has an
additional function of enabling auto-media mode between the internal
PHY and SERDES blocks depending on which first gains link.
The original intention of commit 5d5b231da7 (net: dsa: mv88e6xxx: use
PHY_DETECT in mac_link_up/mac_link_down) was to allow this bit to be
used to detect when this propagation is enabled, and allow software to
update the port configuration. This has found to be necessary for some
switches which do not automatically propagate status from the SERDES to
the port, which includes the 88E6390. However, commit 4a3e0aeddf
("net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's") breaks
this assumption.
Maarten Zanders has confirmed that the issue he was addressing was for
an 88E6250 switch, which does not have a PHY_DETECT bit in bit 12, but
instead a link status bit. Therefore, mv88e6xxx_port_ppu_updates() does
not report correctly.
This patch resolves the above issues by reverting Maarten's change and
instead making mv88e6xxx_port_ppu_updates() indicate whether the port
is internal for the 88E6250 family of switches.
Yes, you're right, I'm targeting the 6250 family. And yes, your
suggestion would solve my case and is a better implementation for
the other devices (as far as I can see).
Fixes: 4a3e0aeddf ("net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maarten Zanders <maarten.zanders@mind.be>
Link: https://lore.kernel.org/r/E1muXm7-00EwJB-7n@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We don't really need new switch API for these, and with new switches
which intend to add support for this feature, it will become cumbersome
to maintain.
The change consists in restructuring the two drivers that implement this
offload (sja1105 and mv88e6xxx) such that the offload is enabled and
disabled from the ->port_bridge_{join,leave} methods instead of the old
->port_bridge_tx_fwd_{,un}offload.
The only non-trivial change is that mv88e6xxx_map_virtual_bridge_to_pvt()
has been moved to avoid a forward declaration, and the
mv88e6xxx_reg_lock() calls from inside it have been removed, since
locking is now done from mv88e6xxx_port_bridge_{join,leave}.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a preparation patch for the removal of the DSA switch methods
->port_bridge_tx_fwd_offload() and ->port_bridge_tx_fwd_unoffload().
The plan is for the switch to report whether it offloads TX forwarding
directly as a response to the ->port_bridge_join() method.
This change deals with the noisy portion of converting all existing
function prototypes to take this new boolean pointer argument.
The bool is placed in the cross-chip notifier structure for bridge join,
and a reference to it is provided to drivers. In the next change, DSA
will then actually look at this value instead of calling
->port_bridge_tx_fwd_offload().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The main desire behind this is to provide coherent bridge information to
the fast path without locking.
For example, right now we set dp->bridge_dev and dp->bridge_num from
separate code paths, it is theoretically possible for a packet
transmission to read these two port properties consecutively and find a
bridge number which does not correspond with the bridge device.
Another desire is to start passing more complex bridge information to
dsa_switch_ops functions. For example, with FDB isolation, it is
expected that drivers will need to be passed the bridge which requested
an FDB/MDB entry to be offloaded, and along with that bridge_dev, the
associated bridge_num should be passed too, in case the driver might
want to implement an isolation scheme based on that number.
We already pass the {bridge_dev, bridge_num} pair to the TX forwarding
offload switch API, however we'd like to remove that and squash it into
the basic bridge join/leave API. So that means we need to pass this
pair to the bridge join/leave API.
During dsa_port_bridge_leave, first we unset dp->bridge_dev, then we
call the driver's .port_bridge_leave with what used to be our
dp->bridge_dev, but provided as an argument.
When bridge_dev and bridge_num get folded into a single structure, we
need to preserve this behavior in dsa_port_bridge_leave: we need a copy
of what used to be in dp->bridge.
Switch drivers check bridge membership by comparing dp->bridge_dev with
the provided bridge_dev, but now, if we provide the struct dsa_bridge as
a pointer, they cannot keep comparing dp->bridge to the provided
pointer, since this only points to an on-stack copy. To make this
obvious and prevent driver writers from forgetting and doing stupid
things, in this new API, the struct dsa_bridge is provided as a full
structure (not very large, contains an int and a pointer) instead of a
pointer. An explicit comparison function needs to be used to determine
bridge membership: dsa_port_offloads_bridge().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The location of the bridge device pointer and number is going to change.
It is not going to be kept individually per port, but in a common
structure allocated dynamically and which will have lockdep validation.
Use the helpers to access these elements so that we have a migration
path to the new organization.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The goal of this change is to reduce mv88e6xxx_port_vlan() to a form
where dsa_port_bridge_same() can be used, since the dp->bridge_dev
pointer will be hidden in a future change.
To do that, we observe that the "br" pointer is deduced from a
dp->bridge_dev in both cases (of a physical switch port as well as a
virtual bridge). So instead of keeping the "br" pointer, we can just
keep the "dp" pointer from which "br" gets derived.
In the last iteration over switch ports, we must use another iterator
variable, "other_dp"since now we use the "dp" variable to keep an
indirect reference to the bridge. While at it, the old code used to
filter only the ports which were part of the same switch as "ds".
There exists a dedicated DSA port iterator for that:
dsa_switch_for_each_port (which skips the ports in the tree that belong
to non-local switches), so we can just use that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid a plethora of dsa_to_port() calls (some hidden behind
dsa_is_*_port and some in plain sight) by keeping two struct dsa_port
references: one to the port passed as argument, and another to the other
ports of the switch that we're iterating over.
This isn't called from the DSA initialization path, so there is no risk
that we have user ports without a dp->slave populated. So the combined
checks that a port isn't a DSA port, a CPU port, or doesn't have a slave
net device (therefore is unused), are strictly equivalent to the simple
check that the port is a user port. This is already handled by the DSA
iterator.
i gets replaced by other_dp->index, dsa_is_*_port calls get replaced by
dsa_port_is_*, and dsa_to_port gets replaced by the respective pointer
directly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid repeated calls to dsa_to_port() (some hidden behind dsa_is_user_port
and some in plain sight) by keeping two struct dsa_port references: one
to the port passed as argument, and another to the other ports of the
switch that we're iterating over.
dsa_to_port(ds, i) gets replaced by other_dp, i gets replaced by
other_port which is derived from other_dp->index, dsa_is_user_port is
handled by the DSA iterator.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The service where DSA assigns a unique bridge number for each forwarding
domain is useful even for drivers which do not implement the TX
forwarding offload feature.
For example, drivers might use the dp->bridge_num for FDB isolation.
So rename ds->num_fwd_offloading_bridges to ds->max_num_bridges, and
calculate a unique bridge_num for all drivers that set this value.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I have seen too many bugs already due to the fact that we must encode an
invalid dp->bridge_num as a negative value, because the natural tendency
is to check that invalid value using (!dp->bridge_num). Latest example
can be seen in commit 1bec0f0506 ("net: dsa: fix bridge_num not
getting cleared after ports leaving the bridge").
Convert the existing users to assume that dp->bridge_num == 0 is the
encoding for invalid, and valid bridge numbers start from 1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix following coccicheck warning:
/drivers/net/dsa/ocelot/felix_vsc9959.c:1627:13-20:
WARNING opportunity for kmemdup
/drivers/net/dsa/ocelot/felix_vsc9959.c:1506:16-23:
WARNING opportunity for kmemdup
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211207064419.38632-1-hanyihao@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add an interface so that non-mmio regmaps can be used
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Existing felix devices all have an initialized pcs array. Future devices
might not, so running a NULL check on the array before dereferencing it
will allow those future drivers to not crash at this point
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The pci_bar variables for the switch and imdio don't make sense for the
generic felix driver. Moving them to felix_vsc9959 to limit scope and
simplify the felix_info struct.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GPIO library does copy the of_node from the parent device of
the GPIO chip, there is no need to repeat this in the individual
drivers. Remove assignment here.
For the details one may look into the of_gpio_dev_init() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently autoloading for SPI devices does not use the DT ID table, it
uses SPI modalises. Supporting OF modalises is going to be difficult if
not impractical, an attempt was made but has been reverted, so ensure
that module autoloading works for this driver by adding an id_table
listing the SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the Lantiq
DSA switches and remove the old validate implementation to allow DSA to
use phylink_generic_validate() for this switch driver.
The exclusion of Gigabit linkmodes for MII, Reverse MII and Reduced MII
links is handled within phylink_generic_validate() in phylink, so there
is no need to make them conditional on the interface mode in the driver.
Reviewed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Populate the supported interfaces and MAC capabilities for the
hellcreek DSA switch and remove the old validate implementation to
allow DSA to use phylink_generic_validate() for this switch driver.
The switch actually only supports MII and RGMII, but as phylib defaults
to GMII, we need to include this interface mode to keep existing DT
working.
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Function mv88e6xxx_serdes_pcs_get_state() currently does not report link
up if AN is enabled, Link bit is set, but Speed and Duplex Resolved bit
is not set, which testing shows is the case for when auto-negotiation
was bypassed (we have AN enabled but link partner does not).
An example of such link partner is Marvell 88X3310 PHY, when put into
the mode where host interface changes between 10gbase-r, 5gbase-r,
2500base-x and sgmii according to copper speed. The 88X3310 does not
enable AN in 2500base-x, and so SerDes on mv88e6xxx currently does not
link with it.
Fix this.
Fixes: a5a6858b79 ("net: dsa: mv88e6xxx: extend phylink to Serdes PHYs")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inband AN is broken on Amethyst in 2500base-x mode when set by standard
mechanism (via cmode).
(There probably is some weird setting done by default in the switch for
this mode that make it cycle in some state or something, because when
the peer is the mvneta controller, it receives link change interrupts
every ~0.3ms, but the link is always down.)
Get around this by configuring the PCS mode to 1000base-x (where inband
AN works), and then changing the SerDes frequency while SerDes
transmitter and receiver are disabled, before enabling SerDes PHY. After
disabling SerDes PHY, change the PCS mode back to 2500base-x, to avoid
confusing the device (if we leave it at 1000base-x PCS mode but with
different frequency, and then change cmode to sgmii, the device won't
change the frequency because it thinks it already has the correct one).
The register which changes the frequency is undocumented. I discovered
it by going through all registers in the ranges 4.f000-4.f100 and
1e.8000-1e.8200 for all SerDes cmodes (sgmii, 1000base-x, 2500base-x,
5gbase-r, 10gbase-r, usxgmii) and filtering out registers that didn't
make sense (the value was the same for modes which have different
frequency). The result of this was:
reg sgmii 1000base-x 2500base-x 5gbase-r 10gbase-r usxgmii
04.f002 005b 0058 0059 005c 005d 005f
04.f076 3000 0000 1000 4000 5000 7000
04.f07c 0950 0950 1850 0550 0150 0150
1e.8000 0059 0059 0058 0055 0051 0051
1e.8140 0e20 0e20 0e28 0e21 0e42 0e42
Register 04.f002 is the documented Port Operational Confiuration
register, it's last 3 bits select PCS type, so changing this register
also changes the frequency to the appropriate value.
Registers 04.f076 and 04.f07c are not writable.
Undocumented register 1e.8000 was the one: changing bits 3:0 from 9 to 8
changed SerDes frequency to 3.125 GHz, while leaving the value of PCS
mode in register 04.f002.2:0 at 1000base-x. Inband autonegotiation
started working correctly.
(I didn't try anything with register 1e.8140 since 1e.8000 solved the
problem.)
Since I don't have documentation for this register 1e.8000.3:0, I am
using the constants without names, but my hypothesis is that this
register selects PHY frequency. If in the future I have access to an
oscilloscope able to handle these frequencies, I will try to test this
hypothesis.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fix for erratum 5.2 of the 88E6393X (Amethyst) family: for 10gbase-r
mode, some undocumented registers need to be written some special
values.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save power on 88E6393X by disabling SerDes receiver and transmitter
after SerDes is SerDes is disabled.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for lane is unnecessary, since the function is called only
with allowed lane argument.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to SERDES scripts for 88E6393X, erratum 4.8 has to be applied
every time before SerDes is powered on.
Split the code for erratum 4.8 into separate function and call it in
mv88e6393x_serdes_power().
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zero-length and one-element arrays are deprecated, see
Documentation/process/deprecated.rst
Flexible-array members should be used instead.
Generated by: scripts/coccinelle/misc/flexible_array.cocci
Fixes: 23ae3a7877 ("net: dsa: felix: add stream gate settings for psfp")
CC: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to a shared MDIO access implementation by way of the mdio-mscc-miim
driver.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch seville to use of_mdiobus_register(bus, NULL) instead of just
mdiobus_register. This code is about to be pulled into a separate module
that can optionally define ports by the device_node.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A contact at Realtek has clarified what exactly the units of RGMII RX
delay are. The answer is that the unit of RX delay is "about 0.3 ns".
Take this into account when parsing rx-internal-delay-ps by
approximating the closest step value. Delays of more than 2.1 ns are
rejected.
This obviously contradicts the previous assumption in the driver that a
step value of 4 was "about 2 ns", but Realtek also points out that it is
easy to find more than one RX delay step value which makes RGMII work.
Fixes: 4af2950c50 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Cc: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 4af2950c50 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probe deferral is not an error, so don't log this as an error:
[0.590156] realtek-smi ethernet-switch: unable to register switch ret = -517
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switch family can have up to 8 UTP ports {0..7}. However,
INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK was using 2 bits instead of 3,
dropping the most significant bit during indirect register reads and
writes. Reading or writing ports 4, 5, 6, and 7 registers was actually
manipulating, respectively, ports 0, 1, 2, and 3 registers.
This is not sufficient but necessary to support any variant with more
than 4 UTP ports, like RTL8367S.
rtl8365mb_phy_{read,write} will now returns -EINVAL if phy is greater
than 7.
Fixes: 4af2950c50 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver version is able to handle only one bridge at time.
Configuring two bridges on two different ports would end up shorting this
bridges by HW. To reproduce it:
ip l a name br0 type bridge
ip l a name br1 type bridge
ip l s dev br0 up
ip l s dev br1 up
ip l s lan1 master br0
ip l s dev lan1 up
ip l s lan2 master br1
ip l s dev lan2 up
Ping on lan1 and get response on lan2, which should not happen.
This happened, because current driver version is storing one global "Port VLAN
Membership" and applying it to all ports which are members of any
bridge.
To solve this issue, we need to handle each port separately.
This patch is dropping the global port member storage and calculating
membership dynamically depending on STP state and bridge participation.
Note: STP support was broken before this patch and should be fixed
separately.
Fixes: c2e866911e ("net: dsa: microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20211126123926.2981028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VSC9959 switch embedded within NXP LS1028A (and that version of
Ocelot switches only) supports cut-through forwarding - meaning it can
start the process of looking up the destination ports for a packet, and
forward towards those ports, before the entire packet has been received
(as opposed to the store-and-forward mode).
The up side is having lower forwarding latency for large packets. The
down side is that frames with FCS errors are forwarded instead of being
dropped. However, erroneous frames do not result in incorrect updates of
the FDB or incorrect policer updates, since these processes are deferred
inside the switch to the end of frame. Since the switch starts the
cut-through forwarding process after all packet headers (including IP,
if any) have been processed, packets with large headers and small
payload do not see the benefit of lower forwarding latency.
There are two cases that need special attention.
The first is when a packet is multicast (or flooded) to multiple
destinations, one of which doesn't have cut-through forwarding enabled.
The switch deals with this automatically by disabling cut-through
forwarding for the frame towards all destination ports.
The second is when a packet is forwarded from a port of lower link speed
towards a port of higher link speed. This is not handled by the hardware
and needs software intervention.
Since we practically need to update the cut-through forwarding domain
from paths that aren't serialized by the rtnl_mutex (phylink
mac_link_down/mac_link_up ops), this means we need to serialize physical
link events with user space updates of bonding/bridging domains.
Enabling cut-through forwarding is done per {egress port, traffic class}.
I don't see any reason why this would be a configurable option as long
as it works without issues, and there doesn't appear to be any user
space configuration tool to toggle this on/off, so this patch enables
cut-through forwarding on all eligible ports and traffic classes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211125125808.2383984-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix warning reported by bot.
Make sure hash is init to 0 and fix wrong logic for hash_type in
qca8k_lag_can_offload.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: def975307c ("net: dsa: qca8k: add LAG support")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211123154446.31019-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add LAG support to this switch. In Documentation this is described as
trunk mode. A max of 4 LAGs are supported and each can support up to 4
port. The current tx mode supported is Hash mode with both L2 and L2+3
mode.
When no port are present in the trunk, the trunk is disabled in the
switch.
When a port is disconnected, the traffic is redirected to the other
available port.
The hash mode is global and each LAG require to have the same hash mode
set. To change the hash mode when multiple LAG are configured, it's
required to remove each LAG and set the desired hash mode to the last.
An error is printed when it's asked to set a not supported hadh mode.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports mirror mode. Only one port can set as mirror port and
every other port can set to both ingress and egress mode. The mirror
port is disabled and reverted to normal operation once every port is
removed from sending packet to it.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for mdb add/del function. The ARL table is used to insert
the rule. The rule will be searched, deleted and reinserted with the
port mask updated. The function will check if the rule has to be updated
or insert directly with no deletion of the old rule.
If every port is removed from the port mask, the rule is removed.
The rule is set STATIC in the ARL table (aka it doesn't age) to not be
flushed by fast age function.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k support setting ageing time in step of 7s. Add support for it and
set the max value accepted of 7645m.
Documentation talks about support for 10000m but that values doesn't
make sense as the value doesn't match the max value in the reg.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports fast aging by flushing any rule in the ARL
table for a specific port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently missing 2 additionals MIB counter present in QCA833x
switch.
QC832x switch have 39 MIB counter and QCA833X have 41 MIB counter.
Add the additional MIB counter and rework the MIB function to print the
correct supported counter from the match_data struct.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert any qca8k set/clear/pool to regmap helper and add
missing config to regmap_config struct.
Read/write/rmw operation are reworked to use the regmap helper
internally to keep the delta of this patch low. These additional
function will then be dropped when the code split will be proposed.
Ipq40xx SoC have the internal switch based on the qca8k regmap but use
mmio for read/write/rmw operation instead of mdio.
In preparation for the support of this internal switch, convert the
driver to regmap API to later split the driver to common and specific
code. The overhead introduced by the use of regamp API is marginal as the
internal mdio will bypass it by using its direct access and regmap will be
used only by configuration functions or fdb access.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for regmap conversion, move regmap init in the probe
function and make it mandatory as any read/write/rmw operation will be
converted to regmap API.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mutex is already init in sw_probe. Remove the extra init in qca8k_setup.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert and try to standardize bit fields using
GENMASK/FIELD_PREP/FIELD_GET macros. Rework some logic to support the
standard macro and tidy things up. No functional change intended.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The very next check for port 0 and 6 already makes sure we don't go out
of bounds with the ports_config delay table.
Remove the redundant check.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k has a global MTU, so its tracking the MTU per port to make sure
that the largest MTU gets applied.
Since it uses the frame size instead of MTU the driver MTU change function
will then add the size of Ethernet header and checksum on top of MTU.
The driver currently populates the per port MTU size as Ethernet frame
length + checksum which equals 1518.
The issue is that then MTU change function will go through all of the
ports, find the largest MTU and apply the Ethernet header + checksum on
top of it again, so for a desired MTU of 1500 you will end up with 1536.
This is obviously incorrect, so to correct it populate the per port struct
MTU with just the MTU and not include the Ethernet header + checksum size
as those will be added by the MTU change function.
Fixes: f58d2598cf ("net: dsa: qca8k: implement the port MTU callbacks")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With SGMII phy the internal delay is always applied to the PAD0 config.
This is caused by the falling edge configuration that hardcode the reg
to PAD0 (as the falling edge bits are present only in PAD0 reg)
Move the delay configuration before the reg overwrite to correctly apply
the delay.
Fixes: cef0811584 ("net: dsa: qca8k: set internal delay also for sgmii")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PSFP rules take effect on the streams from any port of VSC9959 switch.
This patch use ingress port to limit the rule only active on this port.
Each stream can only match two ingress source ports in VSC9959. Streams
from lowest port gets the configuration of SFID pointed by MAC Table
lookup and streams from highest port gets the configuration of (SFID+1)
pointed by MAC Table lookup. This patch defines the PSFP rule on highest
port as dummy rule, which means that it does not modify the MAC table.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add police action to set flow meter table which is defined
in IEEE802.1Qci. Flow metering is two rates two buckets and three color
marker to policing the frames, we only enable one rate one bucket in
this patch.
Flow metering shares a same policer pool with VCAP policers, so the PSFP
policer calls ocelot_vcap_policer_add() and ocelot_vcap_policer_del() to
set flow meter police.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Policer was previously automatically assigned from the highest index to
the lowest index from policer pool. But police action of tc flower now
uses index to set an police entry. This patch uses the police index to
set vcap policers, so that one policer can be shared by multiple rules.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds stream gate settings for PSFP. Use SGI table to store
stream gate entries. Disable the gate entry when it is not used by any
stream.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSC9959 supports Per-Stream Filtering and Policing(PSFP) that complies
with the IEEE 802.1Qci standard. The stream is identified by Null stream
identification(DMAC and VLAN ID) defined in IEEE802.1CB.
For PSFP, four tables need to be set up: stream table, stream filter
table, stream gate table, and flow meter table. Identify the stream by
parsing the tc flower keys and add it to the stream table. The stream
filter table is automatically maintained, and its index is determined by
SGID(flow gate index) and FMID(flow meter index).
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vsc73xx_remove() returns zero unconditionally and no caller checks the
returned value. So convert the function to return no value.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Model 88E6191X only supports >1G speeds on port 10. Port 0 and 9 are
only 1G.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211104171747.10509-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Normally it is expected that the dsa_device_ops :: rcv() method finishes
parsing the DSA tag and consumes it, then never looks at it again.
But commit c0bcf53766 ("net: dsa: ocelot: add hardware timestamping
support for Felix") added support for RX timestamping in a very
unconventional way. On this switch, a partial timestamp is available in
the DSA header, but the driver got away with not parsing that timestamp
right away, but instead delayed that parsing for a little longer:
dsa_switch_rcv():
nskb = cpu_dp->rcv(skb, dev); <------------- not here
-> ocelot_rcv()
...
skb = nskb;
skb_push(skb, ETH_HLEN);
skb->pkt_type = PACKET_HOST;
skb->protocol = eth_type_trans(skb, skb->dev);
...
if (dsa_skb_defer_rx_timestamp(p, skb)) <--- but here
-> felix_rxtstamp()
return 0;
When in felix_rxtstamp(), this driver accounted for the fact that
eth_type_trans() happened in the meanwhile, so it got a hold of the
extraction header again by subtracting (ETH_HLEN + OCELOT_TAG_LEN) bytes
from the current skb->data.
This worked for quite some time but was quite fragile from the very
beginning. Not to mention that having DSA tag parsing split in two
different files, under different folders (net/dsa/tag_ocelot.c vs
drivers/net/dsa/ocelot/felix.c) made it quite non-obvious for patches to
come that they might break this.
Finally, the blamed commit does the following: at the end of
ocelot_rcv(), it checks whether the skb payload contains a VLAN header.
If it does, and this port is under a VLAN-aware bridge, that VLAN ID
might not be correct in the sense that the packet might have suffered
VLAN rewriting due to TCAM rules (VCAP IS1). So we consume the VLAN ID
from the skb payload using __skb_vlan_pop(), and take the classified
VLAN ID from the DSA tag, and construct a hwaccel VLAN tag with the
classified VLAN, and the skb payload is VLAN-untagged.
The big problem is that __skb_vlan_pop() does:
memmove(skb->data + VLAN_HLEN, skb->data, 2 * ETH_ALEN);
__skb_pull(skb, VLAN_HLEN);
aka it moves the Ethernet header 4 bytes to the right, and pulls 4 bytes
from the skb headroom (effectively also moving skb->data, by definition).
So for felix_rxtstamp()'s fragile logic, all bets are off now.
Instead of having the "extraction" pointer point to the DSA header,
it actually points to 4 bytes _inside_ the extraction header.
Corollary, the last 4 bytes of the "extraction" header are in fact 4
stale bytes of the destination MAC address from the Ethernet header,
from prior to the __skb_vlan_pop() movement.
So of course, RX timestamps are completely bogus when the system is
configured in this way.
The fix is actually very simple: just don't structure the code like that.
For better or worse, the DSA PTP timestamping API does not offer a
straightforward way for drivers to present their RX timestamps, but
other drivers (sja1105) have established a simple mechanism to carry
their RX timestamp from dsa_device_ops :: rcv() all the way to
dsa_switch_ops :: port_rxtstamp() and even later. That mechanism is to
simply save the partial timestamp to the skb->cb, and complete it later.
Question: why don't we simply populate the skb's struct
skb_shared_hwtstamps from ocelot_rcv(), and bother with this
complication of propagating the timestamp to felix_rxtstamp()?
Answer: dsa_switch_ops :: port_rxtstamp() answers the question whether
PTP packets need sleepable context to retrieve the full RX timestamp.
Currently felix_rxtstamp() answers "no, thanks" to that question, and
calls ocelot_ptp_gettime64() from softirq atomic context. This is
understandable, since Felix VSC9959 is a PCIe memory-mapped switch, so
hardware access does not require sleeping. But the felix driver is
preparing for the introduction of other switches where hardware access
is over a slow bus like SPI or MDIO:
https://lore.kernel.org/lkml/20210814025003.2449143-1-colin.foster@in-advantage.com/
So I would like to keep this code structure, so the rework needed when
that driver will need PTP support will be minimal (answer "yes, I need
deferred context for this skb's RX timestamp", then the partial
timestamp will still be found in the skb->cb.
Fixes: ea440cd2d9 ("net: dsa: tag_ocelot: use VLAN information from tagging header when available")
Reported-by: Po Liu <po.liu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some device set MAC06 exchange in the bootloader. This cause some
problem as we don't support this strange mode and we just set the port6
as the primary CPU port. With MAC06 exchange, PAD0 reg configure port6
instead of port0. Add an extra check and explicitly disable MAC06 exchange
to correctly configure the port PAD config.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Fixes: 3fcf734aa4 ("net: dsa: qca8k: add support for cpu port 6")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GSWIP switch accesses various bridging layer tables (VLANs, FDBs,
forwarding rules) indirectly through PCE registers. These hardware
accesses are non-atomic, being comprised of several register reads and
writes.
These accesses are currently serialized by the rtnl_lock, but DSA is
changing its driver API and that lock will no longer be held when
calling ->port_fdb_add() and ->port_fdb_del().
So this driver needs to serialize the access to the PCE registers using
its own locking scheme. This patch adds that.
Note that the driver also uses the gswip_pce_load_microcode() function
to load a static configuration for the packet classification engine into
a table using the same registers. It is currently not protected, but
since that configuration is only done from the dsa_switch_ops :: setup
method, there is no risk of it being concurrent with other operations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The b53 driver performs non-atomic transactions to the ARL table when
adding, deleting and reading FDB and MDB entries.
Traditionally these were all serialized by the rtnl_lock(), but now it
is possible that DSA calls ->port_fdb_add and ->port_fdb_del without
holding that lock.
So the driver must have its own serialization logic. Add a mutex and
hold it from all entry points (->port_fdb_{add,del,dump},
->port_mdb_{add,del}).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 hardware seems as concurrent as can be, but when we create a
background script that adds/removes a rain of FDB entries without the
rtnl_mutex taken, then in parallel we do another operation like run
'bridge fdb show', we can notice these errors popping up:
sja1105 spi2.0: port 2 failed to read back entry for 00:01:02:03:00:40 vid 0: -ENOENT
sja1105 spi2.0: port 2 failed to add 00:01:02:03:00:40 vid 0 to fdb: -2
sja1105 spi2.0: port 2 failed to read back entry for 00:01:02:03:00:46 vid 0: -ENOENT
sja1105 spi2.0: port 2 failed to add 00:01:02:03:00:46 vid 0 to fdb: -2
Luckily what is going on does not require a major rework in the driver.
The sja1105_dynamic_config_read() function sends multiple SPI buffers to
the peripheral until the operation completes. We should not do anything
until the hardware clears the VALID bit.
But since there is no locking (i.e. right now we are implicitly
serialized by the rtnl_mutex, but if we remove that), it might be
possible that the process which performs the dynamic config read is
preempted and another one performs a dynamic config write.
What will happen in that case is that sja1105_dynamic_config_read(),
when it resumes, expects to see VALIDENT set for the entry it reads
back. But it won't.
This can be corrected by introducing a mutex for serializing SPI
accesses to the dynamic config interface which should be atomic with
respect to each other.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware manual says that software should attempt a new dynamic
config access (be it a a write or a read-back) only while the VALID bit
is cleared. The VALID bit is set by software to 1, and it remains set as
long as the hardware is still processing the request.
Currently the driver only polls for the command completion only for
reads, because that's when we need the actual data read back. Writes
have been more or less "asynchronous", although this has never been an
observable issue.
This change makes sja1105_dynamic_config_write poll the VALID bit as
well, to absolutely ensure that a follow-up access to the static config
finds the VALID bit cleared.
So VALID means "work in progress", while VALIDENT means "entry being
read is valid". On reads we check the VALIDENT bit too, while on writes
that bit is not always defined. So we need to factor it out of the loop,
and make the loop provide back the unpacked command structure, so that
sja1105_dynamic_config_read can check the VALIDENT bit.
The change also attempts to convert the open-coded loop to use the
read_poll_timeout macro, since I know this will come up during review.
It's more code, but hey, it uses read_poll_timeout!
Tested on SJA1105T, SJA1105S, SJA1110A.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looking at the code, the GSWIP switch appears to hold bridging service
structures (VLANs, FDBs, forwarding rules) in PCE table entries.
Hardware access to the PCE table is non-atomic, and is comprised of
several register reads and writes.
These accesses are currently serialized by the rtnl_lock, but DSA is
changing its driver API and that lock will no longer be held when
calling ->port_fdb_add() and ->port_fdb_del().
So this driver needs to serialize the access to the PCE table using its
own locking scheme. This patch adds that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
