The jiffies tests in n_tty_receive_overrun() are simplified ratelimiting
(without locking). We could use struct ratelimit_state and the helpers,
but to me, it occurs to be too complex for this use case.
But the code currently tests both if the time passed (the first
time_after()) and if jiffies wrapped around (the second time_after()).
time_is_before_jiffies() takes care of both, provided overrun_time is
initialized at the allocation time.
So switch to time_is_before_jiffies(), the same what ratelimiting does.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230827074147.2287-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configuring a pin as an output pin with a value of logic 0, we
end up as having a value of logic 1 on the output pin. Setting a
logic 0 a second time (or more) after that will correctly output a
logic 0 on the output pin.
By default, all GPIO pins are configured as inputs. When we enter
sc16is7xx_gpio_direction_output() for the first time, we first set the
desired value in IOSTATE, and then we configure the pin as an output.
The datasheet states that writing to IOSTATE register will trigger a
transfer of the value to the I/O pin configured as output, so if the
pin is configured as an input, nothing will be transferred.
Therefore, set the direction first in IODIR, and then set the desired
value in IOSTATE.
This is what is done in NXP application note AN10587.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 679875d1d8 ("sc16is7xx: Separate GPIOs from modem control lines")
and commit 21144bab4f ("sc16is7xx: Handle modem status lines")
changed the function of the GPIOs pins to act as modem control
lines without any possibility of selecting GPIO function.
As a consequence, applications that depends on GPIO lines configured
by default as GPIO pins no longer work as expected.
Also, the change to select modem control lines function was done only
for channel A of dual UART variants (752/762). This was not documented
in the log message.
Allow to specify GPIO or modem control line function in the device
tree, and for each of the ports (A or B).
Do so by using the new device-tree property named
"nxp,modem-control-line-ports" (property added in separate patch).
When registering GPIO chip controller, mask-out GPIO pins declared as
modem control lines according to this new DT property.
Fixes: 679875d1d8 ("sc16is7xx: Separate GPIOs from modem control lines")
Fixes: 21144bab4f ("sc16is7xx: Handle modem status lines")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230807214556.540627-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sc16is7xx_config_rs485() function is called only for the second
port (index 1, channel B), causing initialization problems for the
first port.
For the sc16is7xx driver, port->membase and port->mapbase are not set,
and their default values are 0. And we set port->iobase to the device
index. This means that when the first device is registered using the
uart_add_one_port() function, the following values will be in the port
structure:
port->membase = 0
port->mapbase = 0
port->iobase = 0
Therefore, the function uart_configure_port() in serial_core.c will
exit early because of the following check:
/*
* If there isn't a port here, don't do anything further.
*/
if (!port->iobase && !port->mapbase && !port->membase)
return;
Typically, I2C and SPI drivers do not set port->membase and
port->mapbase.
The max310x driver sets port->membase to ~0 (all ones). By
implementing the same change in this driver, uart_configure_port() is
now correctly executed for all ports.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's rather advised to rely on DMA pause / resume instead of
clearing/setting DMA request enable bit for the same purpose. Some DMA
request/acknowledge race may encountered by doing so. We prefer to use
dmaengine_pause and resume instead to pause a dma transfer when it is
necessary.
Create two new functions (stm32_usart_rx_dma_pause, stm32_usart_rx_dma
_resume) to handle dma error when pausing/resuming.
And rename stm32_usart_start_rx_dma_cyclic() to
stm32_usart_rx_dma_start_or_resume() and use this function to resume an
rx dma transfer. If resume fail, stm32_usart_rx_dma_start_or_resume can
create a new transfer to continue.
It is also safer to close DMA before reset DMAR in stm32_usart_shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-6-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create new function "stm32_usart_dma_pause_resume" that called dmaengine_
pause/resume and in case of error, terminate dma transaction.
Two other functions are created to facilitate the use of stm32_usart_dma
_pause_resume : stm32_usart_tx_dma_pause, stm32_usart_tx_dma_resume.
Equivalent functions for rx will be added in future patch.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-5-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's rather advised to rely on DMA pause / resume instead of
clearing/setting DMA request enable bit for the same purpose. Some DMA
request/acknowledge race may encountered by doing so. We prefer to use
dmaengine_pause and resume instead to pause a dma transfer when it is
necessary.
It is also safer to close DMA before reset DMAT in stm32_usart_shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, changing the parameters of the n_gsm mux gives no direct control
to the user whether this should trigger a mux reset or not. The decision is
solely made by the driver based on the assumption which parameter changes
are compatible or not. Therefore, the user has no means to perform an
automatic mux reset after parameter configuration for non-conflicting
changes.
Add the parameter 'flags' to 'gsm_config_ext' to force a mux reset after
ioctl setting regardless of whether the changes made require this or not
by setting this to 'GSM_FL_RESTART'. This is done similar to
'GSM_FL_RESTART' in gsm_dlci_config.flags.
Note that 'GSM_FL_RESTART' is currently the only allowed flag to allow
additions here.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230817093231.2317-9-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The structure gsm_mux contains the 'unsupported' field. However, there is
currently no place in the code which increases this counter.
Increase the 'unsupported' statistics counter in the following case:
- an unsupported frame type has been requested by the peer via parameter
negotiation
- a control frame with an unsupported but known command has been received
Note that we have no means to detect an inconsistent/unsupported adaptation
sufficient accuracy as this changes the structure of the UI/UIH frames.
E.g. a one byte header is added in case of convergence layer type 2 instead
of 1 and contains the modem signal octet with the state of the signal
lines. There is no checksum or other value which indicates of this field is
correct or should be present. Therefore, we can only assume protocol
correctness here. See also 'gsm_dlci_data()' where this is handled.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230817093231.2317-6-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The malformed counter in gsm_mux is already increased in case of errors
detected in gsm_queue() and gsm1_receive(). gsm_dlci_command() also
detects a case for a malformed frame but does not increase the malformed
counter yet.
Fix this by also increasing the gsm_mux malformed counter in case of a
malformed frame in gsm_dlci_command().
Note that the malformed counter is not yet exposed and only set internally.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230817093231.2317-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the n_gsm link statistics by a failed link open counter in
preparation for an upcoming patch which will expose these.
This counter is increased whenever an attempt to open the control channel
failed. This is true in the following cases:
- new DLCI allocation failed
- connection request (SAMB) with invalid CR flag has been received
- connection response (UA) timed out
- parameter negotiation timed out or failed
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230817093231.2317-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, changing the parameters of a DLCI gives no direct control to the
user whether this should trigger a channel reset or not. The decision is
solely made by the driver based on the assumption which parameter changes
are compatible or not. Therefore, the user has no means to perform an
automatic channel reset after parameter configuration for non-conflicting
changes.
Add the parameter 'flags' to 'gsm_dlci_config' to force a channel reset
after ioctl setting regardless of whether the changes made require this or
not by setting this to 'GSM_FL_RESTART'.
Note that 'GSM_FL_RESTART' is currently the only allow flag to allow
additions here.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230817093231.2317-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the last couple of years Linux kernel got rid of a few architectures
and many platforms. Hence some PORT_* definitions in the serial_core.h
become unused and redundant. Remove them for good.
Removed IDs are checked for users against Debian Code Search engine.
Hence safe to remove as there are no consumers found (only providers).
While at it, add a note about 0-13, that are defined in the other file.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230821083857.1065282-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same as in the previous patch, tty_prepare_flip_string() accepts
size_t as an size argument. It returns the same size (or less). It is
unexpected that it returns a signed value and can confuse users to check
for negative values.
Instead, return the same size_t as accepted to make clear we return
values >= 0, where zero in fact means failure.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230816105530.3335-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the functions accept size_t as a size argument. They finally return
the same size (or less). It is quite unexpected that they return a
signed value and can confuse users to check for negative values.
Instead, return the same size_t as accepted to make clear we return
values >= 0, where zero in fact means failure.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230816105530.3335-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to have tty_buffer::data typed as unsigned long.
Switch to u8, but preserve the ulong alignment using __aligned.
This allows for the cast removal from char_buf_ptr(). And for use of
struct_size() in the allocation in tty_buffer_alloc() -- in the next
patch.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230816105530.3335-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
