2
0
mirror of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git synced 2025-09-04 20:19:47 +08:00
linux/arch/sh/boards/mach-se/7724/setup.c
Linus Torvalds 2e341ca686 Sound updates for 3.5-rc1
This is the first big chunk for 3.5 merges of sound stuff.
 There are a few big changes in different areas.  First off, the
 streaming logic of USB-audio endpoints has been largely rewritten
 for the better support of "implicit feedback".  If anything about USB
 got broken, this change has to be checked.
 
 For HD-audio, the resume procedure was changed; instead of delaying
 the resume of the hardware until the first use, now waking up immediately
 at resume.  This is for buggy BIOS.
 
 For ASoC, dynamic PCM support and the improved support for digital links
 between off-SoC devices are major framework changes.
 
 Some highlights are below:
 
 * HD-audio
 - Avoid the accesses of invalid pin-control bits that may stall the codec
 - V-ref setup cleanups
 - Fix the races in power-saving code
 - Fix the races in codec cache hashes and connection lists
 - Split some common codes for BIOS auto-parser to hda_auto_parser.c
 - Changed the PM resume code to wake up immediately for buggy BIOS
 - Creative SoundCore3D support
 - Add Conexant CX20751/2/3/4 codec support
 
 * ASoC
 - Dynamic PCM support, allowing support for SoCs with internal routing
   through components with tight sequencing and formatting constraints
   within their internal paths or where there are multiple components
   connected with CPU managed DMA controllers inside the SoC.
 - Greatly improved support for direct digital links between off-SoC
   devices, providing a much simpler way of connecting things like digital
   basebands to CODECs.
 - Much more fine grained and robust locking, cleaning up some of the
   confusion that crept in with multi-component.
 - CPU support for nVidia Tegra 30 I2S and audio hub controllers and
   ST-Ericsson MSP I2S controolers
 - New CODEC drivers for Cirrus CS42L52, LAPIS Semiconductor ML26124, Texas
   Instruments LM49453.
 - Some regmap changes needed by the Tegra I2S driver.
 - mc13783 audio support.
 
 * Misc
 - Rewrite with module_pci_driver()
 - Xonar DGX support for snd-oxygen
 - Improvement of packet handling in snd-firewire driver
 - New USB-endpoint streaming logic
 - Enhanced M-audio FTU quirks and relevant cleanups
 - Increment the support of OSS devices to 256
 - snd-aloop accuracy improvement
 
 There are a few more pending changes for 3.5, but they will be
 sent slightly later as partly depending on the changes of DRM.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQIcBAABAgAGBQJPvD/9AAoJEGwxgFQ9KSmkPsIP/AuBGpAZy7b7FiEEIy1Hhdws
 US8WVuPzyDslMVdzZ8OFqyPXanIcL9gscoOGMZOEy7UFtMBiR4GuYiPRPubEMxuP
 /gopUqK4SqIsIwT238qqYszSJSxE7gNEZ/2jhSGtkX4EkaSZ4bAskn0iOKX5uw2f
 kTUQknA1rNLIGba2z6rJbgIW7hdxGfpFy05ruv3ct81nO+5JlgyLuP/v5R6jL+do
 cum0N4dJFRd9YSEi2BG612gdz8LJyzOgPqBKmxMEva6BfqLkR8EdP80FtE3eEOiP
 Et1q2LhZwOlBt0BEjsjjOVxMsgxVax6ps9cuNRTk5ECEOldU5dbDatC45L/e9mSD
 OQVUjYAX1mQAtYva4U4PPn6WU6ma2L5yjy4peCObtyCMkEchXk1bfs4CEfVqCXUP
 yFYN8C+y6osZOyWE3+Enn9ifZdWyLeSVq6CT33Yt+fyKlswp6gRkhKYiEPqTA5aU
 p71X59Pp7q1y3tQwiMJNpf2QdkxuxfKURHswdc4BS9ct0mdZhQX0GyDS7OffkTd4
 Lq5UkVMHA1rLlF9oRPd2C9P4BuMEuvLjf662YCKiw+mWFYdBC036DHLLjm1Hcwuj
 UkpQ2PSrrdHG1u0c3ooZ9dQj1BNX4LoABLqvaMtce6sESD/hJ5gcprYJWvtituwM
 ZzZiJavIWsoJ+SWQWBHe
 =+JSm
 -----END PGP SIGNATURE-----

Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound

Pull sound updates from Takashi Iwai:
 "This is the first big chunk for 3.5 merges of sound stuff.

  There are a few big changes in different areas.  First off, the
  streaming logic of USB-audio endpoints has been largely rewritten for
  the better support of "implicit feedback".  If anything about USB got
  broken, this change has to be checked.

  For HD-audio, the resume procedure was changed; instead of delaying
  the resume of the hardware until the first use, now waking up
  immediately at resume.  This is for buggy BIOS.

  For ASoC, dynamic PCM support and the improved support for digital
  links between off-SoC devices are major framework changes.

  Some highlights are below:

  * HD-audio
   - Avoid accesses of invalid pin-control bits that may stall the codec
   - V-ref setup cleanups
   - Fix the races in power-saving code
   - Fix the races in codec cache hashes and connection lists
   - Split some common codes for BIOS auto-parser to hda_auto_parser.c
   - Changed the PM resume code to wake up immediately for buggy BIOS
   - Creative SoundCore3D support
   - Add Conexant CX20751/2/3/4 codec support

  * ASoC
   - Dynamic PCM support, allowing support for SoCs with internal
     routing through components with tight sequencing and formatting
     constraints within their internal paths or where there are multiple
     components connected with CPU managed DMA controllers inside the
     SoC.
   - Greatly improved support for direct digital links between off-SoC
     devices, providing a much simpler way of connecting things like
     digital basebands to CODECs.
   - Much more fine grained and robust locking, cleaning up some of the
     confusion that crept in with multi-component.
   - CPU support for nVidia Tegra 30 I2S and audio hub controllers and
     ST-Ericsson MSP I2S controolers
   - New CODEC drivers for Cirrus CS42L52, LAPIS Semiconductor ML26124,
     Texas Instruments LM49453.
   - Some regmap changes needed by the Tegra I2S driver.
   - mc13783 audio support.

  * Misc
   - Rewrite with module_pci_driver()
   - Xonar DGX support for snd-oxygen
   - Improvement of packet handling in snd-firewire driver
   - New USB-endpoint streaming logic
   - Enhanced M-audio FTU quirks and relevant cleanups
   - Increment the support of OSS devices to 256
   - snd-aloop accuracy improvement

  There are a few more pending changes for 3.5, but they will be sent
  slightly later as partly depending on the changes of DRM."

Fix up conflicts in regmap (due to duplicate patches, with some further
updates then having already come in from the regmap tree).  Also some
fairly trivial context conflicts in the imx and mcx soc drivers.

* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (280 commits)
  ALSA: snd-usb: fix stream info output in /proc
  ALSA: pcm - Add proper state checks to snd_pcm_drain()
  ALSA: sh: Fix up namespace collision in sh_dac_audio.
  ALSA: hda/realtek - Fix unused variable compile warning
  ASoC: sh: fsi: enable chip specific data transfer mode
  ASoC: sh: fsi: call fsi_hw_startup/shutdown from fsi_dai_trigger()
  ASoC: sh: fsi: use same format for IN/OUT
  ASoC: sh: fsi: add fsi_version() and removed meaningless version check
  ASoC: sh: fsi: use register field macro name on IN/OUT_DMAC
  ASoC: tegra: Add machine driver for WM8753 codec
  ALSA: hda - Fix possible races of accesses to connection list array
  ASoC: OMAP: HDMI: Introduce codec
  ARM: mx31_3ds: Add sound support
  ASoC: imx-mc13783 cleanup
  mx31moboard: Add sound support
  ASoC: mc13783 codec cleanups
  ASoC: add imx-mc13783 sound support
  ASoC: Add mc13783 codec
  mfd: mc13xxx: add codec platform data
  ASoC: don't flip master of DT-instantiated DAI links
  ...
2012-05-23 13:05:43 -07:00

942 lines
22 KiB
C

/*
* linux/arch/sh/boards/se/7724/setup.c
*
* Copyright (C) 2009 Renesas Solutions Corp.
*
* Kuninori Morimoto <morimoto.kuninori@renesas.com>
*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*/
#include <linux/init.h>
#include <linux/device.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/mmc/host.h>
#include <linux/mmc/sh_mobile_sdhi.h>
#include <linux/mtd/physmap.h>
#include <linux/delay.h>
#include <linux/smc91x.h>
#include <linux/gpio.h>
#include <linux/input.h>
#include <linux/input/sh_keysc.h>
#include <linux/usb/r8a66597.h>
#include <linux/sh_eth.h>
#include <linux/sh_intc.h>
#include <linux/videodev2.h>
#include <video/sh_mobile_lcdc.h>
#include <media/sh_mobile_ceu.h>
#include <sound/sh_fsi.h>
#include <sound/simple_card.h>
#include <asm/io.h>
#include <asm/heartbeat.h>
#include <asm/clock.h>
#include <asm/suspend.h>
#include <cpu/sh7724.h>
#include <mach-se/mach/se7724.h>
/*
* SWx 1234 5678
* ------------------------------------
* SW31 : 1001 1100 : default
* SW32 : 0111 1111 : use on board flash
*
* SW41 : abxx xxxx -> a = 0 : Analog monitor
* 1 : Digital monitor
* b = 0 : VGA
* 1 : 720p
*/
/*
* about 720p
*
* When you use 1280 x 720 lcdc output,
* you should change OSC6 lcdc clock from 25.175MHz to 74.25MHz,
* and change SW41 to use 720p
*/
/*
* about sound
*
* This setup.c supports FSI slave mode.
* Please change J20, J21, J22 pin to 1-2 connection.
*/
/* Heartbeat */
static struct resource heartbeat_resource = {
.start = PA_LED,
.end = PA_LED,
.flags = IORESOURCE_MEM | IORESOURCE_MEM_16BIT,
};
static struct platform_device heartbeat_device = {
.name = "heartbeat",
.id = -1,
.num_resources = 1,
.resource = &heartbeat_resource,
};
/* LAN91C111 */
static struct smc91x_platdata smc91x_info = {
.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
};
static struct resource smc91x_eth_resources[] = {
[0] = {
.name = "SMC91C111" ,
.start = 0x1a300300,
.end = 0x1a30030f,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ0_SMC,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
},
};
static struct platform_device smc91x_eth_device = {
.name = "smc91x",
.num_resources = ARRAY_SIZE(smc91x_eth_resources),
.resource = smc91x_eth_resources,
.dev = {
.platform_data = &smc91x_info,
},
};
/* MTD */
static struct mtd_partition nor_flash_partitions[] = {
{
.name = "uboot",
.offset = 0,
.size = (1 * 1024 * 1024),
.mask_flags = MTD_WRITEABLE, /* Read-only */
}, {
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = (2 * 1024 * 1024),
}, {
.name = "free-area",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
},
};
static struct physmap_flash_data nor_flash_data = {
.width = 2,
.parts = nor_flash_partitions,
.nr_parts = ARRAY_SIZE(nor_flash_partitions),
};
static struct resource nor_flash_resources[] = {
[0] = {
.name = "NOR Flash",
.start = 0x00000000,
.end = 0x01ffffff,
.flags = IORESOURCE_MEM,
}
};
static struct platform_device nor_flash_device = {
.name = "physmap-flash",
.resource = nor_flash_resources,
.num_resources = ARRAY_SIZE(nor_flash_resources),
.dev = {
.platform_data = &nor_flash_data,
},
};
/* LCDC */
static const struct fb_videomode lcdc_720p_modes[] = {
{
.name = "LB070WV1",
.sync = 0, /* hsync and vsync are active low */
.xres = 1280,
.yres = 720,
.left_margin = 220,
.right_margin = 110,
.hsync_len = 40,
.upper_margin = 20,
.lower_margin = 5,
.vsync_len = 5,
},
};
static const struct fb_videomode lcdc_vga_modes[] = {
{
.name = "LB070WV1",
.sync = 0, /* hsync and vsync are active low */
.xres = 640,
.yres = 480,
.left_margin = 105,
.right_margin = 50,
.hsync_len = 96,
.upper_margin = 33,
.lower_margin = 10,
.vsync_len = 2,
},
};
static struct sh_mobile_lcdc_info lcdc_info = {
.clock_source = LCDC_CLK_EXTERNAL,
.ch[0] = {
.chan = LCDC_CHAN_MAINLCD,
.fourcc = V4L2_PIX_FMT_RGB565,
.clock_divider = 1,
.panel_cfg = { /* 7.0 inch */
.width = 152,
.height = 91,
},
}
};
static struct resource lcdc_resources[] = {
[0] = {
.name = "LCDC",
.start = 0xfe940000,
.end = 0xfe942fff,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = evt2irq(0xf40),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device lcdc_device = {
.name = "sh_mobile_lcdc_fb",
.num_resources = ARRAY_SIZE(lcdc_resources),
.resource = lcdc_resources,
.dev = {
.platform_data = &lcdc_info,
},
};
/* CEU0 */
static struct sh_mobile_ceu_info sh_mobile_ceu0_info = {
.flags = SH_CEU_FLAG_USE_8BIT_BUS,
};
static struct resource ceu0_resources[] = {
[0] = {
.name = "CEU0",
.start = 0xfe910000,
.end = 0xfe91009f,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = evt2irq(0x880),
.flags = IORESOURCE_IRQ,
},
[2] = {
/* place holder for contiguous memory */
},
};
static struct platform_device ceu0_device = {
.name = "sh_mobile_ceu",
.id = 0, /* "ceu0" clock */
.num_resources = ARRAY_SIZE(ceu0_resources),
.resource = ceu0_resources,
.dev = {
.platform_data = &sh_mobile_ceu0_info,
},
};
/* CEU1 */
static struct sh_mobile_ceu_info sh_mobile_ceu1_info = {
.flags = SH_CEU_FLAG_USE_8BIT_BUS,
};
static struct resource ceu1_resources[] = {
[0] = {
.name = "CEU1",
.start = 0xfe914000,
.end = 0xfe91409f,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = evt2irq(0x9e0),
.flags = IORESOURCE_IRQ,
},
[2] = {
/* place holder for contiguous memory */
},
};
static struct platform_device ceu1_device = {
.name = "sh_mobile_ceu",
.id = 1, /* "ceu1" clock */
.num_resources = ARRAY_SIZE(ceu1_resources),
.resource = ceu1_resources,
.dev = {
.platform_data = &sh_mobile_ceu1_info,
},
};
/* FSI */
/* change J20, J21, J22 pin to 1-2 connection to use slave mode */
static struct sh_fsi_platform_info fsi_info = {
.port_a = {
.flags = SH_FSI_BRS_INV,
},
};
static struct resource fsi_resources[] = {
[0] = {
.name = "FSI",
.start = 0xFE3C0000,
.end = 0xFE3C021d,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = evt2irq(0xf80),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device fsi_device = {
.name = "sh_fsi",
.id = 0,
.num_resources = ARRAY_SIZE(fsi_resources),
.resource = fsi_resources,
.dev = {
.platform_data = &fsi_info,
},
};
static struct asoc_simple_dai_init_info fsi2_ak4642_init_info = {
.fmt = SND_SOC_DAIFMT_LEFT_J,
.codec_daifmt = SND_SOC_DAIFMT_CBM_CFM,
.cpu_daifmt = SND_SOC_DAIFMT_CBS_CFS,
.sysclk = 11289600,
};
static struct asoc_simple_card_info fsi_ak4642_info = {
.name = "AK4642",
.card = "FSIA-AK4642",
.cpu_dai = "fsia-dai",
.codec = "ak4642-codec.0-0012",
.platform = "sh_fsi.0",
.codec_dai = "ak4642-hifi",
.init = &fsi2_ak4642_init_info,
};
static struct platform_device fsi_ak4642_device = {
.name = "asoc-simple-card",
.dev = {
.platform_data = &fsi_ak4642_info,
},
};
/* KEYSC in SoC (Needs SW33-2 set to ON) */
static struct sh_keysc_info keysc_info = {
.mode = SH_KEYSC_MODE_1,
.scan_timing = 3,
.delay = 50,
.keycodes = {
KEY_1, KEY_2, KEY_3, KEY_4, KEY_5,
KEY_6, KEY_7, KEY_8, KEY_9, KEY_A,
KEY_B, KEY_C, KEY_D, KEY_E, KEY_F,
KEY_G, KEY_H, KEY_I, KEY_K, KEY_L,
KEY_M, KEY_N, KEY_O, KEY_P, KEY_Q,
KEY_R, KEY_S, KEY_T, KEY_U, KEY_V,
},
};
static struct resource keysc_resources[] = {
[0] = {
.name = "KEYSC",
.start = 0x044b0000,
.end = 0x044b000f,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = evt2irq(0xbe0),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device keysc_device = {
.name = "sh_keysc",
.id = 0, /* "keysc0" clock */
.num_resources = ARRAY_SIZE(keysc_resources),
.resource = keysc_resources,
.dev = {
.platform_data = &keysc_info,
},
};
/* SH Eth */
static struct resource sh_eth_resources[] = {
[0] = {
.start = SH_ETH_ADDR,
.end = SH_ETH_ADDR + 0x1FC,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = evt2irq(0xd60),
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
},
};
static struct sh_eth_plat_data sh_eth_plat = {
.phy = 0x1f, /* SMSC LAN8187 */
.edmac_endian = EDMAC_LITTLE_ENDIAN,
};
static struct platform_device sh_eth_device = {
.name = "sh-eth",
.id = 0,
.dev = {
.platform_data = &sh_eth_plat,
},
.num_resources = ARRAY_SIZE(sh_eth_resources),
.resource = sh_eth_resources,
};
static struct r8a66597_platdata sh7724_usb0_host_data = {
.on_chip = 1,
};
static struct resource sh7724_usb0_host_resources[] = {
[0] = {
.start = 0xa4d80000,
.end = 0xa4d80124 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = evt2irq(0xa20),
.end = evt2irq(0xa20),
.flags = IORESOURCE_IRQ | IRQF_TRIGGER_LOW,
},
};
static struct platform_device sh7724_usb0_host_device = {
.name = "r8a66597_hcd",
.id = 0,
.dev = {
.dma_mask = NULL, /* not use dma */
.coherent_dma_mask = 0xffffffff,
.platform_data = &sh7724_usb0_host_data,
},
.num_resources = ARRAY_SIZE(sh7724_usb0_host_resources),
.resource = sh7724_usb0_host_resources,
};
static struct r8a66597_platdata sh7724_usb1_gadget_data = {
.on_chip = 1,
};
static struct resource sh7724_usb1_gadget_resources[] = {
[0] = {
.start = 0xa4d90000,
.end = 0xa4d90123,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = evt2irq(0xa40),
.end = evt2irq(0xa40),
.flags = IORESOURCE_IRQ | IRQF_TRIGGER_LOW,
},
};
static struct platform_device sh7724_usb1_gadget_device = {
.name = "r8a66597_udc",
.id = 1, /* USB1 */
.dev = {
.dma_mask = NULL, /* not use dma */
.coherent_dma_mask = 0xffffffff,
.platform_data = &sh7724_usb1_gadget_data,
},
.num_resources = ARRAY_SIZE(sh7724_usb1_gadget_resources),
.resource = sh7724_usb1_gadget_resources,
};
static struct resource sdhi0_cn7_resources[] = {
[0] = {
.name = "SDHI0",
.start = 0x04ce0000,
.end = 0x04ce00ff,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = evt2irq(0xe80),
.flags = IORESOURCE_IRQ,
},
};
static struct sh_mobile_sdhi_info sh7724_sdhi0_data = {
.dma_slave_tx = SHDMA_SLAVE_SDHI0_TX,
.dma_slave_rx = SHDMA_SLAVE_SDHI0_RX,
.tmio_caps = MMC_CAP_SDIO_IRQ,
};
static struct platform_device sdhi0_cn7_device = {
.name = "sh_mobile_sdhi",
.id = 0,
.num_resources = ARRAY_SIZE(sdhi0_cn7_resources),
.resource = sdhi0_cn7_resources,
.dev = {
.platform_data = &sh7724_sdhi0_data,
},
};
static struct resource sdhi1_cn8_resources[] = {
[0] = {
.name = "SDHI1",
.start = 0x04cf0000,
.end = 0x04cf00ff,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = evt2irq(0x4e0),
.flags = IORESOURCE_IRQ,
},
};
static struct sh_mobile_sdhi_info sh7724_sdhi1_data = {
.dma_slave_tx = SHDMA_SLAVE_SDHI1_TX,
.dma_slave_rx = SHDMA_SLAVE_SDHI1_RX,
.tmio_caps = MMC_CAP_SDIO_IRQ,
};
static struct platform_device sdhi1_cn8_device = {
.name = "sh_mobile_sdhi",
.id = 1,
.num_resources = ARRAY_SIZE(sdhi1_cn8_resources),
.resource = sdhi1_cn8_resources,
.dev = {
.platform_data = &sh7724_sdhi1_data,
},
};
/* IrDA */
static struct resource irda_resources[] = {
[0] = {
.name = "IrDA",
.start = 0xA45D0000,
.end = 0xA45D0049,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = evt2irq(0x480),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device irda_device = {
.name = "sh_sir",
.num_resources = ARRAY_SIZE(irda_resources),
.resource = irda_resources,
};
#include <media/ak881x.h>
#include <media/sh_vou.h>
static struct ak881x_pdata ak881x_pdata = {
.flags = AK881X_IF_MODE_SLAVE,
};
static struct i2c_board_info ak8813 = {
/* With open J18 jumper address is 0x21 */
I2C_BOARD_INFO("ak8813", 0x20),
.platform_data = &ak881x_pdata,
};
static struct sh_vou_pdata sh_vou_pdata = {
.bus_fmt = SH_VOU_BUS_8BIT,
.flags = SH_VOU_HSYNC_LOW | SH_VOU_VSYNC_LOW,
.board_info = &ak8813,
.i2c_adap = 0,
};
static struct resource sh_vou_resources[] = {
[0] = {
.start = 0xfe960000,
.end = 0xfe962043,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = evt2irq(0x8e0),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device vou_device = {
.name = "sh-vou",
.id = -1,
.num_resources = ARRAY_SIZE(sh_vou_resources),
.resource = sh_vou_resources,
.dev = {
.platform_data = &sh_vou_pdata,
},
};
static struct platform_device *ms7724se_devices[] __initdata = {
&heartbeat_device,
&smc91x_eth_device,
&lcdc_device,
&nor_flash_device,
&ceu0_device,
&ceu1_device,
&keysc_device,
&sh_eth_device,
&sh7724_usb0_host_device,
&sh7724_usb1_gadget_device,
&fsi_device,
&fsi_ak4642_device,
&sdhi0_cn7_device,
&sdhi1_cn8_device,
&irda_device,
&vou_device,
};
/* I2C device */
static struct i2c_board_info i2c0_devices[] = {
{
I2C_BOARD_INFO("ak4642", 0x12),
},
};
#define EEPROM_OP 0xBA206000
#define EEPROM_ADR 0xBA206004
#define EEPROM_DATA 0xBA20600C
#define EEPROM_STAT 0xBA206010
#define EEPROM_STRT 0xBA206014
static int __init sh_eth_is_eeprom_ready(void)
{
int t = 10000;
while (t--) {
if (!__raw_readw(EEPROM_STAT))
return 1;
udelay(1);
}
printk(KERN_ERR "ms7724se can not access to eeprom\n");
return 0;
}
static void __init sh_eth_init(void)
{
int i;
u16 mac;
/* check EEPROM status */
if (!sh_eth_is_eeprom_ready())
return;
/* read MAC addr from EEPROM */
for (i = 0 ; i < 3 ; i++) {
__raw_writew(0x0, EEPROM_OP); /* read */
__raw_writew(i*2, EEPROM_ADR);
__raw_writew(0x1, EEPROM_STRT);
if (!sh_eth_is_eeprom_ready())
return;
mac = __raw_readw(EEPROM_DATA);
sh_eth_plat.mac_addr[i << 1] = mac & 0xff;
sh_eth_plat.mac_addr[(i << 1) + 1] = mac >> 8;
}
}
#define SW4140 0xBA201000
#define FPGA_OUT 0xBA200400
#define PORT_HIZA 0xA4050158
#define PORT_MSELCRB 0xA4050182
#define SW41_A 0x0100
#define SW41_B 0x0200
#define SW41_C 0x0400
#define SW41_D 0x0800
#define SW41_E 0x1000
#define SW41_F 0x2000
#define SW41_G 0x4000
#define SW41_H 0x8000
extern char ms7724se_sdram_enter_start;
extern char ms7724se_sdram_enter_end;
extern char ms7724se_sdram_leave_start;
extern char ms7724se_sdram_leave_end;
static int __init arch_setup(void)
{
/* enable I2C device */
i2c_register_board_info(0, i2c0_devices,
ARRAY_SIZE(i2c0_devices));
return 0;
}
arch_initcall(arch_setup);
static int __init devices_setup(void)
{
u16 sw = __raw_readw(SW4140); /* select camera, monitor */
struct clk *clk;
u16 fpga_out;
/* register board specific self-refresh code */
sh_mobile_register_self_refresh(SUSP_SH_STANDBY | SUSP_SH_SF |
SUSP_SH_RSTANDBY,
&ms7724se_sdram_enter_start,
&ms7724se_sdram_enter_end,
&ms7724se_sdram_leave_start,
&ms7724se_sdram_leave_end);
/* Reset Release */
fpga_out = __raw_readw(FPGA_OUT);
/* bit4: NTSC_PDN, bit5: NTSC_RESET */
fpga_out &= ~((1 << 1) | /* LAN */
(1 << 4) | /* AK8813 PDN */
(1 << 5) | /* AK8813 RESET */
(1 << 6) | /* VIDEO DAC */
(1 << 7) | /* AK4643 */
(1 << 8) | /* IrDA */
(1 << 12) | /* USB0 */
(1 << 14)); /* RMII */
__raw_writew(fpga_out | (1 << 4), FPGA_OUT);
udelay(10);
/* AK8813 RESET */
__raw_writew(fpga_out | (1 << 5), FPGA_OUT);
udelay(10);
__raw_writew(fpga_out, FPGA_OUT);
/* turn on USB clocks, use external clock */
__raw_writew((__raw_readw(PORT_MSELCRB) & ~0xc000) | 0x8000, PORT_MSELCRB);
/* Let LED9 show STATUS2 */
gpio_request(GPIO_FN_STATUS2, NULL);
/* Lit LED10 show STATUS0 */
gpio_request(GPIO_FN_STATUS0, NULL);
/* Lit LED11 show PDSTATUS */
gpio_request(GPIO_FN_PDSTATUS, NULL);
/* enable USB0 port */
__raw_writew(0x0600, 0xa40501d4);
/* enable USB1 port */
__raw_writew(0x0600, 0xa4050192);
/* enable IRQ 0,1,2 */
gpio_request(GPIO_FN_INTC_IRQ0, NULL);
gpio_request(GPIO_FN_INTC_IRQ1, NULL);
gpio_request(GPIO_FN_INTC_IRQ2, NULL);
/* enable SCIFA3 */
gpio_request(GPIO_FN_SCIF3_I_SCK, NULL);
gpio_request(GPIO_FN_SCIF3_I_RXD, NULL);
gpio_request(GPIO_FN_SCIF3_I_TXD, NULL);
gpio_request(GPIO_FN_SCIF3_I_CTS, NULL);
gpio_request(GPIO_FN_SCIF3_I_RTS, NULL);
/* enable LCDC */
gpio_request(GPIO_FN_LCDD23, NULL);
gpio_request(GPIO_FN_LCDD22, NULL);
gpio_request(GPIO_FN_LCDD21, NULL);
gpio_request(GPIO_FN_LCDD20, NULL);
gpio_request(GPIO_FN_LCDD19, NULL);
gpio_request(GPIO_FN_LCDD18, NULL);
gpio_request(GPIO_FN_LCDD17, NULL);
gpio_request(GPIO_FN_LCDD16, NULL);
gpio_request(GPIO_FN_LCDD15, NULL);
gpio_request(GPIO_FN_LCDD14, NULL);
gpio_request(GPIO_FN_LCDD13, NULL);
gpio_request(GPIO_FN_LCDD12, NULL);
gpio_request(GPIO_FN_LCDD11, NULL);
gpio_request(GPIO_FN_LCDD10, NULL);
gpio_request(GPIO_FN_LCDD9, NULL);
gpio_request(GPIO_FN_LCDD8, NULL);
gpio_request(GPIO_FN_LCDD7, NULL);
gpio_request(GPIO_FN_LCDD6, NULL);
gpio_request(GPIO_FN_LCDD5, NULL);
gpio_request(GPIO_FN_LCDD4, NULL);
gpio_request(GPIO_FN_LCDD3, NULL);
gpio_request(GPIO_FN_LCDD2, NULL);
gpio_request(GPIO_FN_LCDD1, NULL);
gpio_request(GPIO_FN_LCDD0, NULL);
gpio_request(GPIO_FN_LCDDISP, NULL);
gpio_request(GPIO_FN_LCDHSYN, NULL);
gpio_request(GPIO_FN_LCDDCK, NULL);
gpio_request(GPIO_FN_LCDVSYN, NULL);
gpio_request(GPIO_FN_LCDDON, NULL);
gpio_request(GPIO_FN_LCDVEPWC, NULL);
gpio_request(GPIO_FN_LCDVCPWC, NULL);
gpio_request(GPIO_FN_LCDRD, NULL);
gpio_request(GPIO_FN_LCDLCLK, NULL);
__raw_writew((__raw_readw(PORT_HIZA) & ~0x0001), PORT_HIZA);
/* enable CEU0 */
gpio_request(GPIO_FN_VIO0_D15, NULL);
gpio_request(GPIO_FN_VIO0_D14, NULL);
gpio_request(GPIO_FN_VIO0_D13, NULL);
gpio_request(GPIO_FN_VIO0_D12, NULL);
gpio_request(GPIO_FN_VIO0_D11, NULL);
gpio_request(GPIO_FN_VIO0_D10, NULL);
gpio_request(GPIO_FN_VIO0_D9, NULL);
gpio_request(GPIO_FN_VIO0_D8, NULL);
gpio_request(GPIO_FN_VIO0_D7, NULL);
gpio_request(GPIO_FN_VIO0_D6, NULL);
gpio_request(GPIO_FN_VIO0_D5, NULL);
gpio_request(GPIO_FN_VIO0_D4, NULL);
gpio_request(GPIO_FN_VIO0_D3, NULL);
gpio_request(GPIO_FN_VIO0_D2, NULL);
gpio_request(GPIO_FN_VIO0_D1, NULL);
gpio_request(GPIO_FN_VIO0_D0, NULL);
gpio_request(GPIO_FN_VIO0_VD, NULL);
gpio_request(GPIO_FN_VIO0_CLK, NULL);
gpio_request(GPIO_FN_VIO0_FLD, NULL);
gpio_request(GPIO_FN_VIO0_HD, NULL);
platform_resource_setup_memory(&ceu0_device, "ceu0", 4 << 20);
/* enable CEU1 */
gpio_request(GPIO_FN_VIO1_D7, NULL);
gpio_request(GPIO_FN_VIO1_D6, NULL);
gpio_request(GPIO_FN_VIO1_D5, NULL);
gpio_request(GPIO_FN_VIO1_D4, NULL);
gpio_request(GPIO_FN_VIO1_D3, NULL);
gpio_request(GPIO_FN_VIO1_D2, NULL);
gpio_request(GPIO_FN_VIO1_D1, NULL);
gpio_request(GPIO_FN_VIO1_D0, NULL);
gpio_request(GPIO_FN_VIO1_FLD, NULL);
gpio_request(GPIO_FN_VIO1_HD, NULL);
gpio_request(GPIO_FN_VIO1_VD, NULL);
gpio_request(GPIO_FN_VIO1_CLK, NULL);
platform_resource_setup_memory(&ceu1_device, "ceu1", 4 << 20);
/* KEYSC */
gpio_request(GPIO_FN_KEYOUT5_IN5, NULL);
gpio_request(GPIO_FN_KEYOUT4_IN6, NULL);
gpio_request(GPIO_FN_KEYIN4, NULL);
gpio_request(GPIO_FN_KEYIN3, NULL);
gpio_request(GPIO_FN_KEYIN2, NULL);
gpio_request(GPIO_FN_KEYIN1, NULL);
gpio_request(GPIO_FN_KEYIN0, NULL);
gpio_request(GPIO_FN_KEYOUT3, NULL);
gpio_request(GPIO_FN_KEYOUT2, NULL);
gpio_request(GPIO_FN_KEYOUT1, NULL);
gpio_request(GPIO_FN_KEYOUT0, NULL);
/* enable FSI */
gpio_request(GPIO_FN_FSIMCKA, NULL);
gpio_request(GPIO_FN_FSIIASD, NULL);
gpio_request(GPIO_FN_FSIOASD, NULL);
gpio_request(GPIO_FN_FSIIABCK, NULL);
gpio_request(GPIO_FN_FSIIALRCK, NULL);
gpio_request(GPIO_FN_FSIOABCK, NULL);
gpio_request(GPIO_FN_FSIOALRCK, NULL);
gpio_request(GPIO_FN_CLKAUDIOAO, NULL);
/* set SPU2 clock to 83.4 MHz */
clk = clk_get(NULL, "spu_clk");
if (!IS_ERR(clk)) {
clk_set_rate(clk, clk_round_rate(clk, 83333333));
clk_put(clk);
}
/* change parent of FSI A */
clk = clk_get(NULL, "fsia_clk");
if (!IS_ERR(clk)) {
/* 48kHz dummy clock was used to make sure 1/1 divide */
clk_set_rate(&sh7724_fsimcka_clk, 48000);
clk_set_parent(clk, &sh7724_fsimcka_clk);
clk_set_rate(clk, 48000);
clk_put(clk);
}
/* SDHI0 connected to cn7 */
gpio_request(GPIO_FN_SDHI0CD, NULL);
gpio_request(GPIO_FN_SDHI0WP, NULL);
gpio_request(GPIO_FN_SDHI0D3, NULL);
gpio_request(GPIO_FN_SDHI0D2, NULL);
gpio_request(GPIO_FN_SDHI0D1, NULL);
gpio_request(GPIO_FN_SDHI0D0, NULL);
gpio_request(GPIO_FN_SDHI0CMD, NULL);
gpio_request(GPIO_FN_SDHI0CLK, NULL);
/* SDHI1 connected to cn8 */
gpio_request(GPIO_FN_SDHI1CD, NULL);
gpio_request(GPIO_FN_SDHI1WP, NULL);
gpio_request(GPIO_FN_SDHI1D3, NULL);
gpio_request(GPIO_FN_SDHI1D2, NULL);
gpio_request(GPIO_FN_SDHI1D1, NULL);
gpio_request(GPIO_FN_SDHI1D0, NULL);
gpio_request(GPIO_FN_SDHI1CMD, NULL);
gpio_request(GPIO_FN_SDHI1CLK, NULL);
/* enable IrDA */
gpio_request(GPIO_FN_IRDA_OUT, NULL);
gpio_request(GPIO_FN_IRDA_IN, NULL);
/*
* enable SH-Eth
*
* please remove J33 pin from your board !!
*
* ms7724 board should not use GPIO_FN_LNKSTA pin
* So, This time PTX5 is set to input pin
*/
gpio_request(GPIO_FN_RMII_RXD0, NULL);
gpio_request(GPIO_FN_RMII_RXD1, NULL);
gpio_request(GPIO_FN_RMII_TXD0, NULL);
gpio_request(GPIO_FN_RMII_TXD1, NULL);
gpio_request(GPIO_FN_RMII_REF_CLK, NULL);
gpio_request(GPIO_FN_RMII_TX_EN, NULL);
gpio_request(GPIO_FN_RMII_RX_ER, NULL);
gpio_request(GPIO_FN_RMII_CRS_DV, NULL);
gpio_request(GPIO_FN_MDIO, NULL);
gpio_request(GPIO_FN_MDC, NULL);
gpio_request(GPIO_PTX5, NULL);
gpio_direction_input(GPIO_PTX5);
sh_eth_init();
if (sw & SW41_B) {
/* 720p */
lcdc_info.ch[0].lcd_modes = lcdc_720p_modes;
lcdc_info.ch[0].num_modes = ARRAY_SIZE(lcdc_720p_modes);
} else {
/* VGA */
lcdc_info.ch[0].lcd_modes = lcdc_vga_modes;
lcdc_info.ch[0].num_modes = ARRAY_SIZE(lcdc_vga_modes);
}
if (sw & SW41_A) {
/* Digital monitor */
lcdc_info.ch[0].interface_type = RGB18;
lcdc_info.ch[0].flags = 0;
} else {
/* Analog monitor */
lcdc_info.ch[0].interface_type = RGB24;
lcdc_info.ch[0].flags = LCDC_FLAGS_DWPOL;
}
/* VOU */
gpio_request(GPIO_FN_DV_D15, NULL);
gpio_request(GPIO_FN_DV_D14, NULL);
gpio_request(GPIO_FN_DV_D13, NULL);
gpio_request(GPIO_FN_DV_D12, NULL);
gpio_request(GPIO_FN_DV_D11, NULL);
gpio_request(GPIO_FN_DV_D10, NULL);
gpio_request(GPIO_FN_DV_D9, NULL);
gpio_request(GPIO_FN_DV_D8, NULL);
gpio_request(GPIO_FN_DV_CLKI, NULL);
gpio_request(GPIO_FN_DV_CLK, NULL);
gpio_request(GPIO_FN_DV_VSYNC, NULL);
gpio_request(GPIO_FN_DV_HSYNC, NULL);
return platform_add_devices(ms7724se_devices,
ARRAY_SIZE(ms7724se_devices));
}
device_initcall(devices_setup);
static struct sh_machine_vector mv_ms7724se __initmv = {
.mv_name = "ms7724se",
.mv_init_irq = init_se7724_IRQ,
};