This is a prerequisite to allocate a per driver self_id workqueue.
This reverts the ohci.c part of patch
fe2af11c22.
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
a) Sort device IDs by vendor -- device -- revision.
b) Write quirk flags in hexadecimal. This affects the user-visible
output of "modinfo firewire-ohci". Since more flags have been added
recently, it is now easier to cope with them in hexadecimal represen-
tation. Besides, the device-specific combination of quirk flags is
shown in hexadecimal in the kernel log too. (And firewire-sbp2
presents its own quirk flags in modinfo as hexadecimals as well.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
We have got
struct descriptor *descriptors;
dma_addr_t descriptors_bus;
dma_addr_t buffer_bus;
struct descriptor buffer[0];
void *misc_buffer;
dma_addr_t misc_buffer_bus;
__be32 *config_rom;
dma_addr_t config_rom_bus;
__be32 *next_config_rom;
dma_addr_t next_config_rom_bus;
But then we have got
__le32 *self_id_cpu;
dma_addr_t self_id_bus;
Better apply the pattern of xyz vs. xyz_bus to self_id vs. self_id_bus
as well. The _cpu suffix looks particularly weird in conversions from
little endian to CPU endian.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Commit 18d627113b (firewire: prevent dropping of completed iso packet
header data) was intended to be an obvious bug fix, but libdc1394 and
FlyCap2 depend on the old behaviour by ignoring all returned information
and thus not noticing that not all packets have been received yet. The
result was that the video frame buffers would be saved before they
contained the correct data.
Reintroduce the old behaviour for old clients.
Tested-by: Stepan Salenikovich <stepan.salenikovich@gmail.com>
Tested-by: Josep Bosch <jep250@gmail.com>
Cc: <stable@vger.kernel.org> # 3.4+
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
A stack trace is an invaluable tool in determining the basis
and cause of PHY regs read/write failures.
Include PHY reg addr (and value for writes) in the diagnostic.
[Stefan R: changed whitespace]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Many of the error messages possible from bus_reset_work() do not
contain enough information to distinguish which error condition
occurred nor enough information to evaluate the error afterwards.
Differentiate all error conditions in bus_reset_work(); add
additional information to make error diagnosis possible.
[Stefan R: fixed self-ID endian conversion]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Convert dev_xxxx(ohci->card.device, ...) log functions to
ohci_xxxx(ohci, ...).
[Stefan R: Peter argues that this increases readability of the code.]
[Stefan R: changed whitespace]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add quirk for VT6306 wake bit behavior.
VT6306 seems to reread the wrong descriptor when the wake bit is
written. work around by putting a copy of the branch address in the
first descriptor of the block.
[Stefan R: This fixes the known broken video reception via gstreamer
on VIA VT6306. 100% repeatable testcase:
$ gst-launch-0.10 dv1394src \! dvdemux \! dvdec \! xvimagesink
with a camcorder or other DV source connected. Likewise for MPEG2-TS
reception via gstreamer, e.g. from TV settop boxes.
Perhaps this also fixes dv4l on VT6306, but this is as yet untested.
Kino, dvgrab or FFADO had not been affected by this chip quirk.
Additional comments from Andy:]
I've looked into some problems with the wake bit on a vt6306 family
chip (1106:3044, rev 46).
I used this firewire card in a mythtv setup (ISO receive MPEG2 stream)
with Debian 2.6.32 kernels for ~2 years without problems.
Since upgrading to 3.2, I've been having problems with the input stream
freezing -- input data stops until I restart mythtv (I expect closing
and reopening the device would be sufficient). This happens
infrequently, maybe one out of 20 recordings. I eventually determined
that the problem is more likely to occur if the system is loaded.
I isolated the kernel version as the triggering SW factor and then
specifically the change from dualbuffer back to packet-per-buffer DMA
mode.
The possibility that the controller does not properly respond to the
wake bit was suggested in
https://bugzilla.redhat.com/show_bug.cgi?id=415841, but not proven.
Based on the fact that dualbuffer mode worked while packet-per-buffer
has trouble, I guessed that upon seeing the wake bit written, the vt6306
controller only checks the branch address in the first descriptor of the
block, even if that is not the correct place to look (because the block
has multiple descriptors).
This theory seems to be correct. When the ISO reception is hung, I am
able to resume it by manually writing the branch address to the first
descriptor in the block, and then writing the wake bit.
I've had luck so far with the attached patch, so I'm including it. It's
probably not a complete solution -- I haven't tested transmit modes to
see whether they have a similar issue.
I doubt that the quirk test is any cheaper than just writing the extra
branch address in all cases, but it does reduce the risk of breaking
other hardware.
[Stefan R: omitted QUIRK_NO_MSI from VT6306 quirks table entry,
changed whitespace]
Signed-off-by: Andy Leiserson <andy@leiserson.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
A pci device can be removed while in its suspended state. If the ohci
host controller is suspended, the PHY is also in low-power mode and
LPS is disabled. If LPS is disabled, most of the host registers aren't
accessible, including IntMaskClear. Furthermore, access to these registers
when LPS is disabled can cause hard lockups on some hardware. Since
interrupts are already disabled in this mode, further action is
unnecessary.
Test LPS before attempting to write IntMaskClear to disable interrupts.
[Stefan R: whitespace changes]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
A pci device can be removed while in its suspended state.
Because the ohci driver freed the irq to suspend, free_irq() is
called twice; once from pci_remove() and again from pci_suspend(),
which issues the warning below [1].
Rather than allocate the irq in the .enable() path, move the
allocation to .probe(). Consequently, the irq is not reallocated
upon pci_resume() and thus is not freed upon pci_suspend().
[1] Warning reported by Mark Einon <mark.einon@gmail.com> when
suspending an MSI MS-1727 GT740 laptop on Ubuntu 3.5.0-22-generic
WARNING: at ./kernel/irq/manage.c:1198 __free_irq+0xa3/0x1e0()
Hardware name: MS-1727
Trying to free already-free IRQ 16
Modules linked in: ip6table_filter ip6_tables ebtable_nat ebtables <...snip...>
Pid: 4, comm: kworker/0:0 Tainted: P O 3.5.0-22-generic #34-Ubuntu
Call Trace:
[<ffffffff81051c1f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff81051d16>] warn_slowpath_fmt+0x46/0x50
[<ffffffff8103fa39>] ? default_spin_lock_flags+0x9/0x10
[<ffffffff810df6b3>] __free_irq+0xa3/0x1e0
[<ffffffff810df844>] free_irq+0x54/0xc0
[<ffffffffa005a27e>] pci_remove+0x6e/0x210 [firewire_ohci]
[<ffffffff8135ae7f>] pci_device_remove+0x3f/0x110
[<ffffffff8141fdbc>] __device_release_driver+0x7c/0xe0
[<ffffffff8141fe4c>] device_release_driver+0x2c/0x40
[<ffffffff8141f5f1>] bus_remove_device+0xe1/0x120
[<ffffffff8141cd1a>] device_del+0x12a/0x1c0
[<ffffffff8141cdc6>] device_unregister+0x16/0x30
[<ffffffff81354784>] pci_stop_bus_device+0x94/0xa0
[<ffffffffa0091c67>] acpiphp_disable_slot+0xb7/0x1a0 [acpiphp]
[<ffffffffa0090716>] ? get_slot_status+0x46/0xc0 [acpiphp]
[<ffffffffa0091d7d>] acpiphp_check_bridge.isra.15+0x2d/0xf0 [acpiphp]
[<ffffffffa0092442>] _handle_hotplug_event_bridge+0x372/0x4d0 [acpiphp]
[<ffffffff81390f8c>] ? acpi_os_execute_deferred+0x2f/0x34
[<ffffffff8116e22d>] ? kfree+0xed/0x110
[<ffffffff8107086a>] process_one_work+0x12a/0x420
[<ffffffffa00920d0>] ? _handle_hotplug_event_func+0x1d0/0x1d0 [acpiphp]
[<ffffffff8107141e>] worker_thread+0x12e/0x2f0
[<ffffffff810712f0>] ? manage_workers.isra.26+0x200/0x200
[<ffffffff81075f13>] kthread+0x93/0xa0
[<ffffffff8168d024>] kernel_thread_helper+0x4/0x10
[<ffffffff81075e80>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff8168d020>] ? gs_change+0x13/0x13
Reported-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The old IEEE 1394 driver stack was removed in v2.6.37. That made the
checks for two Kconfig (module) macros unneeded, since they will now
always evaluate to true. Remove these two checks.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"Asynchronous" is misspelled in some comments. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In case of a self constructed selfID packet this patch correctly
determines the information if the TSB41BA3D phy initiated a bus reset.
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
OHCI 1.1 says:
| Since the value of this bit is undefined after reset in all IR
| contexts, software shall initialize this bit to zero in all contexts
| whether or not active to maintain the exclusive nature of this bit.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
pci_request_region() does not fail on resources that have not been
allocated by the BIOS or by the kernel, so to avoid accessing
registers that are not there, we have to check for this explicitly.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The Bus_Time CSR is virtually never used, so we can avoid burning CPU in
interrupt context for 1 or 3 IsochronousCycleTimer accesses every minute
by not tracking the bus time until the CSR is actually accessed for the
first time.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
bus_reset_work() is only called from workqueue thread context.
ohci_set_config_rom() and ohci_allocate_iso_context() perform GFP_KERNEL
memory allocations, therefore they must be called with interrupts
enabled.
Hence these functions may disable and enable local IRQs without having
to track IRQ state.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch converts the drivers in drivers/firewire/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
- Some SBP-2 initiator fixes, side product from ongoing work on a target.
- Reintroduction of an isochronous I/O feature of the older ieee1394 driver
stack (flush buffer completions); it was evidently rarely used but not
actually unused. Matching libraw1394 code is already available.
- Be sure to prefix all kernel log messages with device name or card name,
and other logging related cleanups.
- Misc other small cleanups, among them a small API change that affects
sound/firewire/ too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=oWbr
-----END PGP SIGNATURE-----
Merge tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull IEEE 1394 (FireWire) subsystem updates post v3.3 from Stefan Richter:
- Some SBP-2 initiator fixes, side product from ongoing work on a target.
- Reintroduction of an isochronous I/O feature of the older ieee1394 driver
stack (flush buffer completions); it was evidently rarely used but not
actually unused. Matching libraw1394 code is already available.
- Be sure to prefix all kernel log messages with device name or card name,
and other logging related cleanups.
- Misc other small cleanups, among them a small API change that affects
sound/firewire/ too. Clemens Ladisch is aware of it.
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394: (26 commits)
firewire: allow explicit flushing of iso packet completions
firewire: prevent dropping of completed iso packet header data
firewire: ohci: factor out iso completion flushing code
firewire: ohci: simplify iso header pointer arithmetic
firewire: ohci: optimize control bit checks
firewire: ohci: remove unused excess_bytes field
firewire: ohci: copy_iso_headers(): make comment match the code
firewire: cdev: fix IR multichannel event documentation
firewire: ohci: fix too-early completion of IR multichannel buffers
firewire: ohci: move runtime debug facility out of #ifdef
firewire: tone down some diagnostic log messages
firewire: sbp2: replace a GFP_ATOMIC allocation
firewire: sbp2: Fix SCSI sense data mangling
firewire: sbp2: Ignore SBP-2 targets on the local node
firewire: sbp2: Take into account Unit_Unique_ID
firewire: nosy: Use the macro DMA_BIT_MASK().
firewire: core: convert AR-req handler lock from _irqsave to _bh
firewire: core: fix race at address_handler unregistration
firewire: core: remove obsolete comment
firewire: core: prefix log messages with card name
...
Extend the kernel and userspace APIs to allow reporting all currently
completed isochronous packets, even if the next interrupt packet has not
yet been reached. This is required to determine the status of the
packets at the end of a paused or stopped stream, and useful for more
precise synchronization of audio streams.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The buffer for the header data of completed iso packets has a fixed
size, so it is possible to configure a stream with a big interval
between interrupt packets or with big headers so that this buffer would
overflow. Previously, ohci.c would drop any data that would not fit,
but this could make unsuspecting applications believe that fewer than
the actual number of packets have completed.
Instead of dropping data, add calls to flush_iso_completion() so that
there are as many events as needed to report all of the data.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In preparation for the following patches that add more flushing, move
the code for flushing accumulated header data into a common function.
The timestamp of the last completed packed is passed through the context
structure instead of a function parameter to allow accessing this value
later outside of the handle_i?_packet functions.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
When storing the header data of completed iso packets, we effectively
treat the buffers as arrays of quadlets. Actually declaring the
pointers as u32* avoids repetitive pointer arithmetic, removes the
unhelpfully named "i" variables, and thus makes the code clearer.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Doing the endian conversion on the constant instead of the memory
field allows the compiler to do the conversion at compile time.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Commit 6498ba04ae (remove unused dualbuffer IR code) overlooked
a field in struct iso_context.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The comment incorrectly talked about one little-endian quadlet, while
there are actually two. Furthermore, the endianness of the remaining
headers depends on whatever protocol is used, so don't mention them.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
handle_ir_buffer_fill() assumed that a completed descriptor would be
indicated by a non-zero transfer_status (as in most other descriptors).
However, this field is written by the controller as soon as (the end of)
the first packet has been written into the buffer. As a consequence, if
we happen to run into such a descriptor when the interrupt handler is
executed after such a packet has completed, the descriptor would be
taken out of the list of active descriptors as soon as the buffer had
been partially filled, so the event for the buffer being completely
filled would never be sent.
To fix this, handle descriptors only when they have been completely
filled, i.e., when res_count == 0. (This also matches the condition
that is reported by the controller with an interrupt.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.36+ <stable@vger.kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
CONFIG_FIREWIRE_OHCI_DEBUG could have been exposed to kernel tweakers
if CONFIG_EXPERT was set. But in hindsight, this stuff is far too
useful to omit it. So get rid of two #else branches that are only
going to bitrot otherwise.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The PCIe device
FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd FireWire Host Controller
[1180:e832] (prog-if 10 [OHCI])
is unable to access attached FireWire devices when MSI is enabled but
works if MSI is disabled.
http://www.mail-archive.com/alsa-user@lists.sourceforge.net/msg28251.html
Hence add the "disable MSI" quirks flag for this device, or in fact for
safety and simplicity for all current (R5U230, R5U231, R5U240) and
future Ricoh PCIe 1394 controllers.
Reported-by: Stefan Thomas <kontrapunktstefan@googlemail.com>
Cc: 2.6.36+ <stable@vger.kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The Audigy's SB1394 controller is actually from Texas Instruments
and has the same bus reset packet generation bug, so it needs the
same quirk entry.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.36+ <stable@vger.kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add the dma_sync_single_* calls necessary to ensure proper cache
synchronization for isochronous data buffers on non-coherent
architectures.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If a device's firmware initiates a bus reset by setting the IBR bit in
PHY register 1 without resetting the gap count field to 63 (and without
having sent a PHY configuration packet beforehand), the gap count of
this node will remain at the old value after the bus reset and thus be
inconsistent with the gap count on all other nodes.
The bus manager is supposed to detect the inconsistent gap count values
in the self ID packets and correct them by issuing another bus reset.
However, if the buggy device happens to be the cycle master, and if it
sends a cycle start packet immediately after the bus reset (which is
likely after a long bus reset), then the time between the end of the
selfID phase and the start of the cycle start packet will be based on
the too-small gap count value, so this gap will be too short to be
detected as a subaction gap by the other nodes. This means that the
cycle start packet will be assumed to be self ID data, and will be
stored after the actual self ID quadlets in the self ID buffer.
This garbage in the self ID buffer made firewire-core ignore all of the
self ID data, and thus prevented the Linux bus manager from correcting
the problem. Furthermore, because the bus reset handling was aborted
completely, asynchronous transfers would be no longer handled correctly,
and fw_run_transaction() would hang until the next bus reset.
To fix this, make the detection of inconsistent self IDs more
discriminating: If the invalid data in the self ID buffer looks like
a cycle start packet, we can assume that the previous data in the buffer
is correctly received self ID information, and process it normally.
(We inspect only the first quadlet of the cycle start packet, because
this value is different enough from any valid self ID quadlet, and many
controllers do not store the cycle start packet in five quadlets because
they expect self ID data to have an even number of quadlets.)
This bug has been observed when a bus-powered DesktopKonnekt6 is
switched off with its power button.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Change memory region to ohci "middle address space". This effectively
reduces the number of packets by 50%.
[Stefan R.:] This eliminates 1394 ack packets and improved throughput
by a few percent in some tests with an S400a connection with and without
gap count optimization. Since firewire-net taxes the AR-req DMA unit of
a FireWire controller much more than firewire-sbp2 (which uses the
middle address space with PCI posted writes too), this commit also
changes a related error printk into a ratelimited one as a precaution.
Side note: The IPv4-over-1394 drivers of Mac OS X 10.4, Windows XP SP3,
and the Thesycon 1394 bus driver for Windows all use the middle address
space too.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Takes less source code and machine code, and less runtime with PHYs
other than TSB41BA3D (e.g. TSB81BA3 with device ID 0x831304 which takes
one instead of six read_paged_phy_reg now).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fix: phy_reg_mutex must be held over the write/read_phy_reg pair which
gets PHY port status.
Only print to the log when a TSB41BA3D was found. By far most TSB82AA2
cards have a TSB81BA3, and firewire-ohci can keep quiet about that.
Shorten some strings and comments. Change some whitespace.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch implements a work around for the Texas Instruments PHY
TSB41BA3D. This phy has a bug at least in combination with the TI LLCs
TSB82AA2B and TSB12LV26. The selfid coming from the locally connected
phy is not propagated into the selfid buffer of the OHCI (see
http://www.ti.com/litv/pdf/sllz059 for details). The main idea is to
construct the selfid ourselves.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Code inside bus_reset_work may now sleep. This is a prerequisite to
support a phy from Texas Instruments cleanly. The patch to support this
phy will be submitted later.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/801719 .
An O2Micro PCI Express FireWire controller,
"FireWire (IEEE 1394) [0c00]: O2 Micro, Inc. Device [1217:11f7] (rev 05)"
which is a combination device together with an SDHCI controller and some
sort of storage controller, misses SBP-2 status writes from an attached
FireWire HDD. This problem goes away if MSI is disabled for this
FireWire controller.
The device reportedly does not require QUIRK_CYCLE_TIMER.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (amended changelog)
Cc: <stable@kernel.org>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: ohci: fix DMA unmapping in an error path
firewire: cdev: fix 32 bit userland on 64 bit kernel compat corner cases
If request_irq failed, we would pass wrong arguments to
dma_free_coherent. https://bugzilla.redhat.com/show_bug.cgi?id=728185
Reported-by: Mads Kiilerich
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
When firewire-ohci is bound to a Pinnacle MovieBoard, eventually a
"Register access failure" is logged and an interrupt storm or a kernel
panic happens. https://bugzilla.kernel.org/show_bug.cgi?id=36622
Until this is sorted out (if that is going to succeed at all), let's
just prevent firewire-ohci from touching these devices.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org>
The software reset in firewire-ohci's pci_remove does not have a great
prospect of success if the card was already physically removed at this
point. So let's skip the 500 ms that were spent in retries here.
Also, replace a defined constant by its open-coded value. This is not a
constant from a specification but an arbitrarily chosen retry limit. It
was only used in this single place.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Detect and handle ejection of FireWire CardBus cards in PHY register
accesses:
- The last attempt of firewire-core to reset the bus during shutdown
caused a spurious "firewire_ohci: failed to write phy reg" error
message in the log. Skip this message as well as the prior retry
loop that needlessly took 100 milliseconds.
- In the unlikely case that a PHY register was read right after card
ejection, a bogus value was obtained and possibly acted upon.
Instead, fail the read attempt.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stopping an isochronous reception DMA context takes two loop iterations
in context_stop on several controllers (JMicron, NEC, VIA). But there
is no extra delay necessary between these two reg_read trials; the MMIO
reads themselves are slow enough. Hence bring back the behavior from
before commit dd6254e5c0 "firewire: ohci:
remove superfluous posted write flushes" on these controllers by means
of an "if (i)" condition.
Isochronous context stop is performed in preemptible contexts (and only
rarely), hence this change is of little impact. (Besides, Agere and TI
controllers always, or almost always, have the context stopped already
at the first ContextControl read.)
More important is asynchronous transmit context stop, which is performed
while local interrupts are disabled (on the two AT DMAs in
bus_reset_tasklet, i.e. after a self-ID-complete event). In my
experience with several controllers, tested with a usermode AT-request
transmitter as well as with FTP transmission over firewire-net, the AT
contexts were luckily already stopped at the first ContextControl read,
i.e. never required another MMIO read let alone mdelay. A possible
explanation for this is that the controllers which I tested perhaps stop
AT DMA before they perform the self-ID reception DMA.
But we cannot be sure about that and should keep the interrupts-disabled
busy loop as short as possible. Hence, query the ContextControl
register in 1000 udelay(10) intervals instead of 10 udelay(1000)
intervals. I understand from an estimation by Clemens Ladisch that
stopping a busy DMA context should take microseconds or at worst tens of
microseconds, not milliseconds.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The call to flush_writes() in context_stop() is superfluous because
another register read is done immediately afterwards.
The call to flush_writes() in ar_context_run() does not need to be done
individually for each AR context, so move it to ohci_enable(). This
also makes ohci_enable() clearer because it no longer depends on a side
effect of ar_context_run() to flush its own register writes.
Finally, the setting of a context's wake bit does not need to be flushed
because neither the driver logic nor the API require the CPU to wait for
this action. This removes the last MMIO reads from the packet queueing
code paths.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
When queueing iso packets, the run time is dominated by the two
MMIO accesses that set the DMA context's wake bit. Because most
drivers submit packets in batches, we can save much time by
removing all but the last wakeup.
The internal kernel API is changed to require a call to
fw_iso_context_queue_flush() after a batch of queued packets.
The user space API does not change, so one call to
FW_CDEV_IOC_QUEUE_ISO must specify multiple packets to take
advantage of this optimization.
In my measurements, this patch reduces the time needed to queue
fifty skip packets from userspace to one sixth on a 2.5 GHz CPU,
or to one third at 800 MHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Current implementation of ohci_set_config_rom() uses a deferred
bus reset via fw_schedule_bus_reset(). If clients add multiple
unit descriptors to the config_rom in quick succession, the
deferred bus reset may not have fired before succeeding update
requests have come in. This can lead to an incorrect partial
update of the config_rom for both addition and removal of
config_rom descriptors, as the ohci_set_config_rom() routine
will return -EBUSY if a previous pending update has not been
completed yet; the requested update just gets dropped on the floor.
This patch recognizes that the "in-flight" update can be modified
until it has been processed by the bus-reset, and the locking
in the bus_reset_tasklet ensures that the update is done atomically
with respect to modifications made by ohci_set_config_rom(). The
-EBUSY error case is simply removed.
[Stefan R: The bug always existed at least theoretically. But it
became easy to trigger since 2.6.36 commit 02d37bed18 "firewire: core:
integrate software-forced bus resets with bus management" which
introduced long mandatory delays between janitorial bus resets.]
Signed-off-by: Benjamin Buchalter <bj@mhlabs.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (trivial style changes)
Cc: <stable@kernel.org> # 2.6.36.y and newer
When z==2, the condition "key == 2" is superfluous because it cannot
occur without "b == 3", as a descriptor with b!=3 and key==2 would be
an OUTPUT_MORE_IMMEDIATE descriptor which cannot be used alone.
Also remove magic numbers and needless computations on the b field.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
For AT packet payloads of up to eight bytes, we have enough unused space
in the DMA descriptors list so that we can put a copy of the payload
there and thus avoid having to create a separate streaming DMA mapping
for the payload buffer.
In a CPU-bound microbenchmark that just sends 8-byte packets, bandwidth
was measured to increase by 5.7 %, from 1009 KB/s to 1067 KB/s. In
practice, the only performance-sensitive usage of small asynchronous
packets is the SBP-2 driver's write to the ORB_POINTER register during
SCSI command submission.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
OHCI 1.1 5.7.3 not only forbids enabling or starting any DMA contexts
before the linkEnable bit is set, but also explicitly warns of undefined
behaviour if this order is violated.
Don't violate it then.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
It seems drivers/firewire/ohci.c is making some optimistic assumptions
about struct fw_ohci and that member "card" will always remain the first
member of the struct.
Plus it's probably going to confuse a lot of static code analyzers too.
So I wonder if there is a good reason not to free the ohci struct just
like it was allocated instead of the tricky &ohci->card way?
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
It is perhaps just a rudiment from before mainline submission of the
driver.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Since commit 82b662dc41 "flush AT contexts after bus reset for OHCI 1.2",
the driver takes care of any AT packets that were enqueued during a bus
reset phase. The check from commit 76f73ca1b2 is therefore no longer
necessary and the MMIO read can be avoided.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If a misguided program tried to start an isochronous context before it
has queued any packets, the call would appear to succeed, but the
context would not actually go into the running state, and the OHCI
controller would then raise an unrecoverableError interrupt because the
first Z value is zero and thus invalid. The driver logs such errors,
but there is no mechanism to report this back to the program.
Add an explicit check so that this error can be returned synchronously.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
To prevent the iso packet callback from being called after
fw_iso_context_stop() has returned, make sure that the
context's tasklet has finished executing before that.
This fixes access-after-free bugs that have so far been
observed only in the upcoming snd-firewire-speakers driver,
but can theoretically also happen in the firedtv driver.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
When a DMA context goes into the dead state (and the controller thus
stops working correctly), logging this error and the controller's error
code might be helpful for debugging.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
PAGE_KERNEL_RO is not available on all architectures, so its use
in the new AR code broke compilation on sparc64.
Because the read-only mapping was just a debugging aid, just use
PAGE_KERNEL instead.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
James Bottomley wrote:
> On Thu, 2011-01-13 at 08:27 +0100, Clemens Ladisch wrote:
>> firewire: ohci: fix compilation on arches without PAGE_KERNEL_RO, e.g. sparc
>>
>> PAGE_KERNEL_RO is not available on all architectures, so its use in the
>> new AR code broke compilation on sparc64.
>>
>> Because the R/O mapping is only used to catch drivers that try to write
>> to the reception buffer and not actually required for correct operation,
>> we can just use a normal PAGE_KERNEL mapping where _RO is not available.
[...]
>> +/*
>> + * For archs where PAGE_KERNEL_RO is not supported;
>> + * mapping the AR buffers readonly for the CPU is just a debugging aid.
>> + */
>> +#ifndef PAGE_KERNEL_RO
>> +#define PAGE_KERNEL_RO PAGE_KERNEL
>> +#endif
>
> This might cause interesting issues on sparc64 if it ever acquired a
> PAGE_KERNEL_RO. Sparc64 has extern pgprot_t for it's PAGE_KERNEL types
> rather than #defines, so the #ifdef check wouldn't see this.
>
> I think either PAGE_PROT_RO becomes part of our arch API (so all
> architectures are forced to add it), or, if it's not part of the API,
> ohci isn't entitled to use it. The latter seems simplest since you have
> no real use for write protection anyway.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
"firewire: ohci: restart iso DMA contexts on resume from low power mode"
added the flag struct context.active and "firewire: ohci: cache the
context run bit" added struct context.running.
These flags contain the same information; combine them.
Also, normalize whitespace in pci_resume().
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The DMA context run control bit is entirely controlled by software, so
it is safe to cache it. This allows the driver to avoid doing an
additional MMIO read when queueing an AT packet.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add comments
- on why bus_reset_tasklet flushes AT queues,
- that commit 76f73ca1b2 can possibly be reverted now.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Jarod Wilson <jarod@redhat.com>
The OHCI 1.2 (draft) specification, clause 7.2.3.3, allows and
recommends that, after a bus reset, the controller does not flush all
the packets in the AT queues. Therefore, the driver has to do this
itself.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Restore iso channels DMA so that iso channels could continue to work
after resume from RAM/disk.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Some lousy BIOSes, e.g. my Aspire 5720 BIOS forget to restore the GUID
register on resume from RAM.
Fix that by setting it to the last value that was read from it.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The buffers used for the selfIDs packets and the AR request and response
descriptors end up using three pages because dma_alloc_coherent()
allocates at least one page per call. However, these data structures
would all fit into 4 KB, so we can save space by using a common buffer
for them.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
When the isochRx/isochTx bit is clear, we do not need to read the
corresponding iso interrupt event register.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Change the header of PHY packets to be sent to include a pseudo
transaction code. This makes the header consistent with that of
received PHY packets, and allows at_context_queue_packet() and
log_ar_at_event() to see the packet type directly instead of having
to deduce it from the header length or even from the header contents.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
To remove the error information from the controller's queue and to allow
more posted writes, the driver has to read the failed posted write
address before clearing the postedWriteErr interrupt bit.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
(Stefan R:) The spec is somewhat fuzzy about the actual requirements.
To err on the safe side, let's do these two read accesses.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Make sure that interrupt event clear bit writes are executed before the
interrupt handler returns.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add proper error handling for the context_init() calls.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Move the AR DMA descriptors out of the buffer pages, and map the buffer
pages linearly into the kernel's address space. This allows the driver
to ignore any page boundaries in the DMA data and thus to avoid any
copying around of packet payloads.
This fixes the bug where S800 packets that are so big (> 4080 bytes)
that they can be split over three pages were not handled correctly.
Due to the changed algorithm, we can now use arbitrarily many buffer
pages, which improves performance because the controller can more easily
unload its DMA FIFO.
Furthermore, using streaming DMA mappings should improve perfomance on
architectures where coherent DMA mappings are not cacheable. Even on
other architectures, the caching behaviour should be improved slightly
because the CPU no longer writes to the buffer pages.
v2: Detect the last filled buffer page by searching the descriptor's
residual count value fields in order (like in the old code), instead
of going backwards through the transfer status fields; it looks as
if some controllers do not set the latter correctly.
v3: Fix an old resume bug that would now make the handler run into
a BUG_ON, and replace that check with more useful error handling.
Increase the buffer size for better performance with non-TI chips.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Maxim Levitsky writes:
Works almost perfectly. I can still see RCODE_BUSY errors
sometimes, not very often though. 64K here eliminates these errors
completely. This is most likely due to nouveau drivers and lowest
perf level I use to lower card temperature. That increases
latencies too much I think. Besides that the IO is just perfect.
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Agere FW643 rev 06, listed as "11c1:5901 (rev 06) (prog-if 10 [OHCI])",
produced SBP-2 I/O errors since kernel 2.6.36. Disabling MSI fixes it.
Since MSI work on Agere FW643-E (same vendor and device ID, but rev 07),
introduce a device revision field into firewire-ohci's quirks list so
that different quirks can be defined for older and newer revisions.
Reported-by: Jonathan Isom <jeisom@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org> # 2.6.36.y
"VIA Technologies, Inc. VT6315 Series Firewire Controller [1106:3403]"
does not generate any interrupts if Message Signaled Interrupts were
enabled. This is a regression since kernel 2.6.36 in which MSI support
was added to firewire-ohci. Hence blacklist MSI on all VIA controllers.
Reported-by: Robin Cook <rcook@wyrms.net>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org> # 2.6.36.y
If the controller is storing a split packet and therefore changing
d->res_count to zero between the two reads by the driver, we end up with
an end pointer that is not at a packet boundary, and therefore overflow
the buffer when handling the split packet.
To fix this, read the field once, atomically. The compiler usually
merges the two reads anyway, but for correctness, we have to enforce it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Freeing an AR buffer page just to allocate a new page immediately
afterwards is not only a pointless effort but also dangerous because
the allocation can fail, which would result in an oops later.
Split ar_context_add_page() into two functions so that we can reuse
the old page directly.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
When handling an AR buffer that has been completely filled, we assumed
that its descriptor will not be read by the controller and can be
overwritten. However, when the last received packet happens to end at
the end of the buffer, the controller might not yet have moved on to the
next buffer and might read the branch address later. If we overwrite
and free the page before that, the DMA context will either go dead
because of an invalid Z value, or go off into some random memory.
To fix this, ensure that the descriptor does not get overwritten by
using only the actual buffer instead of the entire page for reassembling
the split packet. Furthermore, to avoid freeing the page too early,
move on to the next buffer only when some data in it guarantees that the
controller has moved on.
This should eliminate the remaining firewire-net problems.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.22-2.6.36 <stable@kernel.org>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
When the controller had to split a received asynchronous packet into two
buffers, the driver tries to reassemble it by copying both parts into
the first page. However, if size + rest > PAGE_SIZE, i.e., if the yet
unhandled packets before the split packet, the split packet itself, and
any received packets after the split packet are together larger than one
page, then the memory after the first page would get overwritten.
To fix this, do not try to copy the data of all unhandled packets at
once, but copy the possibly needed data every time when handling
a packet.
This gets rid of most of the infamous crashes and data corruptions when
using firewire-net.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.22-2.6.36 <stable@kernel.org>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (cast PAGE_SIZE to size_t)
Revert commit 54672386cc
"firewire: ohci: fix up configuration of TI chips".
It caused massive slow-down and data corruption with a TSB82AA2 based
StarTech EC1394B2 ExpressCard and FireWire 800 harddisks.
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/657081http://thread.gmane.org/gmane.linux.kernel.firewire.user/4013
The fact that some card EEPROMs do not program these enhancements may be
related to TSB81BA3 phy chip errata, if not to bugs of TSB82AA2 itself.
We could re-add these configuration steps, but only conditional on a
whitelist of cards on which these enhancements bring a proven positive
effect.
Reported-and-tested-by: Eric Shattow <lucent@gmail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org> 2.6.35
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The Ricoh FireWire controllers appear to have the non-atomic cycle
timer register access bug, so, activate the driver workaround by
default.
The behaviour was observed on:
Ricoh Co Ltd R5C552 IEEE 1394 Controller [1180:0552] and
Ricoh Co Ltd R5C832 IEEE 1394 Controller [1180:0832] (rev 04).
Signed-off-by: Heikki Lindholm <holin@iki.fi>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
VIA VT6306, VIA VT6308, and NEC OrangeLink controllers do not write
packet event codes for received PHY packets (or perhaps write
evt_no_status, hard to tell). Work around it by overwriting the
packet's ACK by ack_complete, so that upper layers that listen to PHY
packet reception get to see these packets.
(Also tested: TI TSB82AA2, TI TSB43AB22/A, TI XIO2213A, Agere FW643,
JMicron JMB381 --- these do not exhibit this bug.)
Clemens proposed a quirks flag for that, IOW whitelist known misbehaving
controllers for this workaround. Though to me it seems harmless enough
to enable for all controllers.
The log_ar_at_event() debug log will continue to show the original
status from the DMA unit.
Reported-by: Clemens Ladisch <clemens@ladisch.de> (VT6308)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Conflicts:
drivers/firewire/core-card.c
drivers/firewire/core-cdev.c
and forgotten #include <linux/time.h> in drivers/firewire/ohci.c
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This adds the DMA context programming and userspace ABI for multichannel
reception, i.e. for listening on multiple channel numbers by means of a
single DMA context.
The use case is reception of more streams than there are IR DMA units
offered by the link layer. This is already implemented by the older
ohci1394 + ieee1394 + raw1394 stack. And as discussed recently on
linux1394-devel, this feature is occasionally used in practice.
The big drawbacks of this mode are that buffer layout and interrupt
generation necessarily differ from single-channel reception: Headers
and trailers are not stripped from packets, packets are not aligned with
buffer chunks, interrupts are per buffer chunk, not per packet.
These drawbacks also cause a rather hefty code footprint to support this
rarely used OHCI-1394 feature. (367 lines added, among them 94 lines of
added userspace ABI documentation.)
This implementation enforces that a multichannel reception context may
only listen to channels to which no single-channel context on the same
link layer is presently listening to. OHCI-1394 would allow to overlay
single-channel contexts by the multi-channel context, but this would be
a departure from the present first-come-first-served policy of IR
context creation.
The implementation is heavily based on an earlier one by Jay Fenlason.
Thanks Jay.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
firewire-ohci keeps book of which isochronous channels are occupied by
IR DMA contexts, so that there cannot be more than one context listening
to a certain channel.
If IR context creation failed due to an out-of-memory condition, this
bookkeeping leaked a channel.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
When we append to a DMA program, we need to ensure that the order in
which initialization of the new descriptors and update of the
branch_address of the old tail descriptor, as seen by the PCI device,
happen as intended.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This extends the FW_CDEV_IOC_SEND_PHY_PACKET ioctl() for /dev/fw* to be
useful for ping time measurements. One application for it would be gap
count optimization in userspace that is based on ping times rather than
hop count. (The latter is implemented in firewire-core itself but is
not applicable to beta PHYs that act as repeater.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add an FW_CDEV_IOC_RECEIVE_PHY_PACKETS ioctl() and
FW_CDEV_EVENT_PHY_PACKET_RECEIVED poll()/read() event for /dev/fw*.
This can be used to get information from remote PHYs by remote access
PHY packets.
This is also the 2nd half of the functionality (the receive part) to
support a userspace implementation of a VersaPHY transaction layer.
Safety considerations:
- PHY packets are generally broadcasts, hence some kind of elevated
privileges should be required of a process to be able to listen in
on PHY packets. This implementation assumes that a process that is
allowed to open the /dev/fw* of a local node does have this
privilege.
There was an inconclusive discussion about introducing POSIX
capabilities as a means to check for user privileges for these
kinds of operations.
Other limitations:
- PHY packet reception may be switched on by ioctl() but cannot be
switched off again. It would be trivial to provide an off switch,
but this is not worth the code. The client should simply close()
the fd then, or just ignore further events.
- For sake of simplicity of API and kernel-side implementation, no
filter per packet content is provided.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Bus resets which are triggered
- by the kernel drivers after updates of the local nodes' config ROM,
- by userspace software via ioctl
shall be deferred until after >=2 seconds after the last bus reset.
If multiple modifications of the local nodes' config ROM happen in a row,
only a single bus reset should happen after them.
When the local node's link goes from inactive to active or vice versa,
and at the two occasions of bus resets mentioned above --- and if the
current gap count differs from 63 --- the bus reset should be preceded
by a PHY configuration packet that reaffirms the gap count. Otherwise a
bus manager would have to reset the bus again right after that.
This is necessary to promote bus stability, e.g. leave grace periods for
allocations and reallocations of isochronous channels and bandwidth,
SBP-2 reconnections etc.; see IEEE 1394 clause 8.2.1.
This change implements all of the above by moving bus reset initiation
into a delayed work (except for bus resets which are triggered by the
bus manager workqueue job and are performed there immediately). It
comes with a necessary addition to the card driver methods that allows
to get the current gap count from PHY registers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Rather than "read a Control and Status Registers (CSR) Architecture
register" I prefer to say "read a Control and Status Register".
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Push the maintenance of STATE_CLEAR/SET.abdicate down into the card
driver. This way, the read/write_csr_reg driver method works uniformly
across all CSR offsets.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
