Add mmio trace events support, currently generic mmio events
KVM_TRACE_MMIO_WRITE/xxx_READ/xx_READ_UNSATISFIED are added here.
Also vcpu id field is added for all kvm trace events, since perf
KVM tool parses vcpu id information for kvm entry event.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
When VM runs in kvm mode, system will not exit to host mode when
executing a general software breakpoint instruction such as INSN_BREAK,
trap exception happens in guest mode rather than host mode. In order to
debug guest kernel on host side, one mechanism should be used to let VM
exit to host mode.
Here a hypercall instruction with a special code is used for software
breakpoint usage. VM exits to host mode and kvm hypervisor identifies
the special hypercall code and sets exit_reason with KVM_EXIT_DEBUG. And
then let qemu handle it.
Idea comes from ppc kvm, one api KVM_REG_LOONGARCH_DEBUG_INST is added
to get the hypercall code. VMM needs get sw breakpoint instruction with
this api and set the corresponding sw break point for guest kernel.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
On LoongArch system, IPI hw uses iocsr registers. There are one iocsr
register access on IPI sending, and two iocsr access on IPI receiving
for the IPI interrupt handler. In VM mode all iocsr accessing will cause
VM to trap into hypervisor. So with one IPI hw notification there will
be three times of trap.
In this patch PV IPI is added for VM, hypercall instruction is used for
IPI sender, and hypervisor will inject an SWI to the destination vcpu.
During the SWI interrupt handler, only CSR.ESTAT register is written to
clear irq. CSR.ESTAT register access will not trap into hypervisor, so
with PV IPI supported, there is one trap with IPI sender, and no trap
with IPI receiver, there is only one trap with IPI notification.
Also this patch adds IPI multicast support, the method is similar with
x86. With IPI multicast support, IPI notification can be sent to at
most 128 vcpus at one time. It greatly reduces the times of trapping
into hypervisor.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Instruction cpucfg can be used to get processor features. And there
is a trap exception when it is executed in VM mode, and also it can be
used to provide cpu features to VM. On real hardware cpucfg area 0 - 20
is used by now. Here one specified area 0x40000000 -- 0x400000ff is used
for KVM hypervisor to provide PV features, and the area can be extended
for other hypervisors in future. This area will never be used for real
HW, it is only used by software.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
On LoongArch system, there is a hypercall instruction special for
virtualization. When system executes this instruction on host side,
there is an illegal instruction exception reported, however it will
trap into host when it is executed in VM mode.
When hypercall is emulated, A0 register is set with value
KVM_HCALL_INVALID_CODE, rather than inject EXCCODE_INE invalid
instruction exception. So VM can continue to executing the next code.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
This patch adds LASX (256bit SIMD) support for LoongArch KVM.
There will be LASX exception in KVM when guest use the LASX instructions.
KVM will enable LASX and restore the vector registers for guest and then
return to guest to continue running.
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
This patch adds LSX (128bit SIMD) support for LoongArch KVM.
There will be LSX exception in KVM when guest use the LSX instructions.
KVM will enable LSX and restore the vector registers for guest and then
return to guest to continue running.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
With halt-polling supported, there is checking for pending events or
interrupts when vcpu executes idle instruction. Pending interrupts
include injected SW interrupts and passthrough HW interrupts, such as
HW timer interrupts, since HW timer works still even if vcpu exists from
VM mode.
Since HW timer pending interrupt can be set directly with CSR status
register, and pending HW timer interrupt checking is used in vcpu block
checking function, it is not necessary to switch to SW timer during
halt-polling. This patch adds preemption disabling in function
kvm_cpu_has_pending_timer(), and removes SW timer switching in idle
instruction emulation function.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Implement kvm exception vectors, using kvm_fault_tables array to save
the handle function pointers and it is used when vcpu handle guest exit.
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Implement handle mmio exception, setting the mmio info into vcpu_run and
return to user space to handle it.
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Implement kvm handle vcpu iocsr exception, setting the iocsr info into
vcpu_run and return to user space to handle it.
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
