The XHCI_RESET_EP_QUIRK was added in 2009 to support prototype xHC
hardware from Fresco Logic that needed an additional configure endpoint
command after a reset endpoint.
That hardware should not have made it to the market.
Now, 13 years later its about time we get rid of it.
quirk was added in commit ac9d8fe7c6 ("USB: xhci: Add quirk for Fresco
Logic xHCI hardware.")
Print a debug message about the removed quirk if against all odds we run
into this controller.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alderlake has two XHCI controllers with PCI IDs 0x461e and 0x51ed. We
had previously added the quirk to default enable runtime PM for 0x461e,
now add it for 0x51ed as well.
Signed-off-by: Evan Green <evgreen@chromium.org>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220408114225.1.Ibcff6b86ed4eacfe4c4bc89c90e18416f3900a3e@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Fresco Logic FL1100 controller needs the TRUST_TX_LENGTH quirk like
other Fresco controllers, but should not have the BROKEN_MSI quirks set.
BROKEN_MSI quirk causes issues in detecting usb drives connected to docks
with this FL1100 controller.
The BROKEN_MSI flag was apparently accidentally set together with the
TRUST_TX_LENGTH quirk
Original patch went to stable so this should go there as well.
Fixes: ea0f69d821 ("xhci: Enable trust tx length quirk for Fresco FL11 USB controller")
Cc: stable@vger.kernel.org
cc: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211221112825.54690-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMD's Yellow Carp platform has few more XHCI controllers,
enable the runtime power management support for the same.
Signed-off-by: Nehal Bakulchandra Shah <Nehal-Bakulchandra.shah@amd.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211215093216.1839065-1-Nehal-Bakulchandra.shah@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=nsMh
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
Struct pci_driver contains a struct device_driver, so for PCI devices, it's
easy to convert a device_driver * to a pci_driver * with to_pci_driver().
The device_driver * is in struct device, so we don't need to also keep
track of the pci_driver * in struct pci_dev.
Replace pdev->driver with to_pci_driver(). This is a step toward removing
pci_dev->driver.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20211004125935.2300113-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
AMD's Yellow Carp platform supports runtime power management for
XHCI Controllers, so enable the same by default for all XHCI Controllers.
[ regrouped and aligned the PCI_DEVICE_ID definitions -Mathias]
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Nehal Bakulchandra Shah <Nehal-Bakulchandra.shah@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211014121200.75433-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested on SD5200T TB3 dock which has Fresco Logic FL1100 USB 3.0 Host
Controller.
Before this patch streaming video from USB cam made mouse and keyboard
connected to the same USB bus unusable. Also video was jerky.
With this patch streaming video doesn't have any effect on other
periferals and video is smooth.
Cc: stable@vger.kernel.org
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Seen on a VLI VL805 PCIe to USB controller. For non-stream endpoints
at least, if the xHC halts on a particular TRB due to an error then
the DCS field in the Out Endpoint Context maintained by the hardware
is not updated with the current cycle state.
Using the quirk XHCI_EP_CTX_BROKEN_DCS and instead fetch the DCS bit
from the TRB that the xHC stopped on.
[ bjorn: rebased to v5.14-rc2 ]
Link: https://github.com/raspberrypi/linux/issues/3060
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the fixes in here, and this resolves a merge issue with
drivers/usb/dwc3/gadget.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a66d21d7db ("usb: xhci: Add support for Renesas controller with
memory") added renesas_usb_fw.mem firmware reference to xhci-pci. Thus
modinfo indicates xhci-pci.ko has "firmware: renesas_usb_fw.mem". But
the firmware is only actually used with CONFIG_USB_XHCI_PCI_RENESAS. An
unusable firmware reference can trigger safety checkers which look for
drivers with unmet firmware dependencies.
Avoid referring to renesas_usb_fw.mem in circumstances when it cannot be
loaded (when CONFIG_USB_XHCI_PCI_RENESAS isn't set).
Fixes: a66d21d7db ("usb: xhci: Add support for Renesas controller with memory")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Thelen <gthelen@google.com>
Link: https://lore.kernel.org/r/20210702071224.3673568-1-gthelen@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI controller is required to enter D3hot rather than D3cold for AMD
s2idle on this hardware generation.
Otherwise, the 'Controller Not Ready' (CNR) bit is not being cleared by
host in resume and eventually this results in xhci resume failures during
the s2idle wakeup.
Link: https://lore.kernel.org/linux-usb/1612527609-7053-1-git-send-email-Prike.Liang@amd.com/
Suggested-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: stable <stable@vger.kernel.org> # 5.11+
Link: https://lore.kernel.org/r/20210527154534.8900-1-mario.limonciello@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of AMD xhci controller require reset on resume.
Occasionally AMD xhci controller does not respond to
Stop endpoint command.
Once the issue happens controller goes into bad state
and in that case controller needs to be reset.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the same way as Intel Tiger Lake TCSS (Type-C Subsystem) the Alder Lake
TCSS xHCI needs to be runtime suspended whenever possible to allow the
TCSS hardware block to enter D3cold and thus save energy.
Cc: stable@vger.kernel.org
Signed-off-by: Abhijeet Rao <abhijeet.rao@intel.com>
Signed-off-by: Nikunj A. Dadhania <nikunj.dadhania@intel.com>
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've confirmed that both the ASMedia ASM1042A and ASM3242 have the same
problem as the ASM1142 and ASM2142/ASM3142, where they lose some of the
upper bits of 64-bit DMA addresses. As with the other chips, this can
cause problems on systems where the upper bits matter, and adding the
XHCI_NO_64BIT_SUPPORT quirk completely fixes the issue.
Cc: stable@vger.kernel.org
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems rt2800usb and mt7601u devices are unable to operate since
commit f8f80be501 ("xhci: Use soft retry to recover faster from
transaction errors")
Seems that some xHCI controllers can not perform Soft Retry correctly,
affecting those devices.
To avoid the problem add xhci->quirks flag that restore pre soft retry
xhci behaviour for affected xHCI controllers. Currently those are
AMD_PROMONTORYA_4 and AMD_PROMONTORYA_2, since it was confirmed
by the users: on those xHCI hosts issue happen and is gone after
disabling Soft Retry.
[minor commit message rewording for checkpatch -Mathias]
Fixes: f8f80be501 ("xhci: Use soft retry to recover faster from transaction errors")
Cc: <stable@vger.kernel.org> # 4.20+
Reported-by: Bernhard <bernhard.gebetsberger@gmx.at>
Tested-by: Bernhard <bernhard.gebetsberger@gmx.at>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202541
Link: https://lore.kernel.org/r/20210311115353.2137560-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Maple Ridge is successor of Titan Ridge Thunderbolt controller. As
Titan Ridge this one also includes xHCI host controller. In order to
safe energy we should put it to low power state by default when idle.
For this reason allow host runtime PM for Maple Ridge.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-5-mathias.nyman@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI controller on Alpine Ridge LP keeps the whole Thunderbolt
controller awake if the host controller is not allowed to sleep.
This is the case even if no USB devices are connected to the host.
Add the Intel Alpine Ridge LP product-id to the list of product-ids
for which we allow runtime PM by default.
Fixes: 2815ef7fe4 ("xhci-pci: allow host runtime PM as default for Intel Alpine and Titan Ridge")
Cc: <stable@vger.kernel.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some platform of AMD, S3 fails with HCE and SRE errors. To fix this,
need to disable a bit which is enable in sparse controller.
Cc: stable@vger.kernel.org #v4.19+
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some atypical users of xhci-pci might need to manually reset their xHCI
controller before starting the HCD setup. Check if a reset controller
device is available to the PCI bus and trigger a reset.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-6-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've confirmed that the ASMedia ASM1142 has the same problem as the
ASM2142/ASM3142, in that it too reports that it supports 64-bit DMA
addresses when in fact it does not. As with the ASM2142/ASM3142, this
can cause problems on systems where the upper bits matter, and adding
the XHCI_NO_64BIT_SUPPORT quirk completely fixes the issue.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200728042408.180529-3-cyrozap@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all ASMedia host controllers have a device ID that matches its part
number. #define some of these IDs to make it clearer at a glance which
chips require what quirks.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Link: https://lore.kernel.org/r/20200728042408.180529-2-cyrozap@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ASM2142/ASM3142 (same PCI IDs) does not support full 64-bit DMA
addresses, which can cause silent memory corruption or IOMMU errors on
platforms that use the upper bits. Add the XHCI_NO_64BIT_SUPPORT quirk
to fix this issue.
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200717112734.328432-1-cyrozap@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some rensas controller like uPD720201 and uPD720202 need firmware to be
loaded. Add these devices in table and invoke renesas firmware loader
functions to check and load the firmware into device memory when
required.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200514122039.300417-4-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_hcd_pci_probe expects users to call this with driver_data set as
hc_driver, that limits the possibility of using the driver_data for
driver data.
Add hc_driver as argument to usb_hcd_pci_probe and modify the callers
ehci/ohci/xhci/uhci to pass hc_driver as argument and freeup the
driver_data used
Tested xhci driver on Dragon-board RB3, compile tested ehci, ohci and
uhci.
[For all but the xHCI parts]
[For the xhci part]
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200514122039.300417-2-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the same way as Intel Ice Lake TCSS (Type-C Subsystem) the Tiger Lake
TCSS xHCI needs to be runtime suspended whenever possible to allow the
TCSS hardware block to enter D3cold and thus save energy.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This PCIe controller chip is used on the Raspberry Pi 4 and multiple
adapter cards. There is no publicly available documentation for the
chip, yet both the downstream RPi4 kernel and the controller cards
support/advertise LPM support.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This controller timeouts during suspend (S3) with
[ 240.521724] xhci_hcd 0000:30:00.3: WARN: xHC save state timeout
[ 240.521729] xhci_hcd 0000:30:00.3: ERROR mismatched command completion event
thus preventing the system from entering S3.
Moreover it remains in an undefined state where some connected devices stop
working until a reboot.
Apply the XHCI_SUSPEND_DELAY quirk to make it suspend properly.
CC: stable@vger.kernel.org
Signed-off-by: Alberto Mattea <alberto@mattea.info>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200306150858.21904-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel hosts that need the XHCI_PME_STUCK_QUIRK flag should enable
runtime pm by calling xhci_pme_acpi_rtd3_enable() before
usb_hcd_pci_probe() calls pci_dev_run_wake().
Otherwise usage count for the device won't be decreased, and runtime
suspend is prevented.
usb_hcd_pci_probe() only decreases the usage count if device can
generate run-time wake-up events, i.e. when pci_dev_run_wake()
returns true.
This issue was exposed by pci_dev_run_wake() change in
commit 8feaec33b9 ("PCI / PM: Always check PME wakeup capability for
runtime wakeup support")
and should be backported to kernels with that change
Cc: <stable@vger.kernel.org> # 4.13+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following build warning is seen if CONFIG_PM is disabled.
drivers/usb/host/xhci-pci.c:498:13: warning:
unused function 'xhci_pci_shutdown'
Fixes: f2c710f7dc ("usb: xhci: only set D3hot for pci device")
Cc: Henry Lin <henryl@nvidia.com>
Cc: stable@vger.kernel.org # all stable releases with f2c710f7dc
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191218011911.6907-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xhci driver cannot call pci_set_power_state() on non-pci xhci host
controllers. For example, NVIDIA Tegra XHCI host controller which acts
as platform device with XHCI_SPURIOUS_WAKEUP quirk set in some platform
hits this issue during shutdown.
Cc: <stable@vger.kernel.org>
Fixes: 638298dc66 ("xhci: Fix spurious wakeups after S5 on Haswell")
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Ice Lake has two xHCI controllers one on PCH and the other as part
of the CPU itself. The latter is also part of the so called Type C
Subsystem (TCSS) sharing ACPI power resources with the PCIe root ports
and the Thunderbolt controllers. In order to put the whole TCSS block
into D3cold the xHCI needs to be runtime suspended as well when idle.
For this reason allow runtime PM as default for Ice Lake TCSS xHCI
controller.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1573836603-10871-5-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_amd_find_chipset_info() is used for chipset detection for
several quirks. It is strange that its return value indicates
the need for the PLL quirk, which means it is often ignored.
This patch adds a function specifically for checking the PLL
quirk like the other ones. Additionally, rename probe_result to
something more appropriate.
Signed-off-by: Ryan Kennedy <ryan5544@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20190704153529.9429-3-ryan5544@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fix enables USB role feature on intel commercial nuc
platform which is based on Kabylake chipset.
Signed-off-by: Balaji Manoharan <m.balaji@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.
To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: <stable@vger.kernel.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement workaround for ThunderX2 Errata-129 (documented in
CN99XX Known Issues" available at Cavium support site).
As per ThunderX2errata-129, USB 2 device may come up as USB 1
if a connection to a USB 1 device is followed by another connection to
a USB 2 device, the link will come up as USB 1 for the USB 2 device.
Resolution: Reset the PHY after the USB 1 device is disconnected.
The PHY reset sequence is done using private registers in XHCI register
space. After the PHY is reset we check for the PLL lock status and retry
the operation if it fails. From our tests, retrying 4 times is sufficient.
Add a new quirk flag XHCI_RESET_PLL_ON_DISCONNECT to invoke the workaround
in handle_xhci_port_status().
Cc: stable@vger.kernel.org
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the shared_hcd pointer is valid when calling usb_put_hcd()
The shared_hcd is removed and freed in xhci by first calling
usb_remove_hcd(xhci->shared_hcd), and later
usb_put_hcd(xhci->shared_hcd)
Afer commit fe190ed0d6 ("xhci: Do not halt the host until both HCD have
disconnected their devices.") the shared_hcd was never properly put as
xhci->shared_hcd was set to NULL before usb_put_hcd(xhci->shared_hcd) was
called.
shared_hcd (USB3) is removed before primary hcd (USB2).
While removing the primary hcd we might need to handle xhci interrupts
to cleanly remove last USB2 devices, therefore we need to set
xhci->shared_hcd to NULL before removing the primary hcd to let xhci
interrupt handler know shared_hcd is no longer available.
xhci-plat.c, xhci-histb.c and xhci-mtk first create both their hcd's before
adding them. so to keep the correct reverse removal order use a temporary
shared_hcd variable for them.
For more details see commit 4ac53087d6 ("usb: xhci: plat: Create both
HCDs before adding them")
Fixes: fe190ed0d6 ("xhci: Do not halt the host until both HCD have disconnected their devices.")
Cc: Joel Stanley <joel@jms.id.au>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: <stable@vger.kernel.org>
Reported-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting added
to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9LlHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnvwCffYmMWyMG9zSOw1oSzFPl7TVN1hYAoMyJqzLg
umyLwWxC9ZWWkrpc3iD8
=ux+Y
-----END PGP SIGNATURE-----
Merge tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting
added to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (229 commits)
usb: phy: ab8500: silence some uninitialized variable warnings
usb: xhci: tegra: Add genpd support
usb: xhci: tegra: Power-off power-domains on removal
usbip:vudc: BUG kmalloc-2048 (Not tainted): Poison overwritten
usbip: tools: fix atoi() on non-null terminated string
USB: misc: appledisplay: fix backlight update_status return code
phy: phy-pxa-usb: add a new driver
usb: host: add DT bindings for faraday fotg2
usb: host: ohci-at91: fix request of irq for optional gpio
usb/early: remove set but not used variable 'remain_length'
usb: typec: Fix copy/paste on typec_set_vconn_role() kerneldoc
usb: typec: tcpm: Report back negotiated PPS voltage and current
USB: core: remove set but not used variable 'udev'
usb: core: fix memory leak on port_dev_path allocation
USB: net2280: Remove ->disconnect() callback from net2280_pullup()
usb: dwc2: disable power_down on rockchip devices
usb: gadget: udc: renesas_usb3: add support for r8a77990
dt-bindings: usb: renesas_usb3: add bindings for r8a77990
usb: gadget: udc: renesas_usb3: Add r8a774a1 support
USB: serial: cypress_m8: remove set but not used variable 'iflag'
...
Intel Apollo Lake has the same internal USB role mux as
Intel Cherry Trail.
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The workaround for missing CAS bit is also needed for xHC on Intel
sunrisepoint PCH. For more details see:
Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci controller on Alpine and Titan Ridge keeps the whole thunderbolt
awake if the host controller is not allowed tp sleep.
This is the case even if no USB devices are connected to the host.
Because of this bigger impact, allow runtime pm as default for these xhci
controllers in the driver.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8466489ef5.
Now that we can properly reset the uPD72020x without a hard PCI reset,
let's get rid of the existing quirks.
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Renesas controllers get into a weird state if they are reset while
programmed with 64bit addresses (they will preserve the top half of the
address in internal, non visible registers).
You end up with half the address coming from the kernel, and the other
half coming from the firmware.
Also, changing the programming leads to extra accesses even if the
controller is supposed to be halted. The controller ends up with a fatal
fault, and is then ripe for being properly reset. On the flip side,
this is completely unsafe if the defvice isn't behind an IOMMU, so
we have to make sure that this is the case. Can you say "broken"?
This is an alternative method to the one introduced in 8466489ef5
("xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"),
which will subsequently be removed.
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Dell Inspiron 5775 is a Raven Ridge. The Enable Slot command timed
out when a USB device gets plugged:
[ 212.156326] xhci_hcd 0000:03:00.3: Error while assigning device slot ID
[ 212.156340] xhci_hcd 0000:03:00.3: Max number of devices this xHCI host supports is 64.
[ 212.156348] usb usb2-port3: couldn't allocate usb_device
AMD suggests that a delay before xHC suspends can fix the issue.
I can confirm it fixes the issue, so use the suspend delay quirk for
Raven Ridge's xHC.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI controller on various Intel SoCs has an extended cap mmio-range
which contains registers to control the muxing to the xHCI (host mode)
or the dwc3 (device mode) and vbus-detection for the otg usb-phy.
Having a role-sw driver included in the xHCI code (under drivers/usb/host)
is not desirable. So this commit adds a simple handler for this extended
capability, which creates a platform device with the caps mmio region as
resource, this allows us to write a separate platform role-sw driver for
the role-switch.
Note this commit adds a call to the new xhci_ext_cap_init() function
to xhci_pci_probe(), it is added here because xhci_ext_cap_init() must
be called only once. If in the future we also want to handle ext-caps
on non pci xHCI HCDs from xhci_ext_cap_init() a call to it should also
be added to other bus probe paths.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device gets plugged on ASUS PRIME B350M-A's front ports, the
xHC stops working:
[ 549.114587] xhci_hcd 0000:02:00.0: WARN: xHC CMD_RUN timeout
[ 549.114608] suspend_common(): xhci_pci_suspend+0x0/0xc0 returns -110
[ 549.114638] xhci_hcd 0000:02:00.0: can't suspend (hcd_pci_runtime_suspend returned -110)
Delay before running xHC command CMD_RUN can workaround the issue.
Use a new quirk to make the delay only targets to the affected xHC.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For AMD Promontory xHCI host, although you can disable USB ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
[commit and code comment rephrasing -Mathias]
Signed-off-by: Joe Lee <asmt.swfae@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When plugging in a USB webcam I see the following message:
xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs
XHCI_TRUST_TX_LENGTH quirk?
handle_tx_event: 913 callbacks suppressed
All is quiet again with this patch (and I've done a fair but of soak
testing with the camera since).
Cc: <stable@vger.kernel.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI driver currently has the IMOD set to 160, which
translates to an IMOD interval of 40,000ns (160 * 250)ns
Commit 0cbd4b34cd ("xhci: mediatek: support MTK xHCI host controller")
introduced a QUIRK for the MTK platform to adjust this interval to 20,
which translates to an IMOD interval of 5,000ns (20 * 250)ns. This is
due to the fact that the MTK controller IMOD interval is 8 times
as much as defined in xHCI spec.
Instead of adding more quirk bits for additional platforms, this patch
introduces the ability for vendors to set the IMOD_INTERVAL as is
optimal for their platform. By using device_property_read_u32() on
"imod-interval-ns", the IMOD INTERVAL can be specified in nano seconds.
If no interval is specified, the default of 40,000ns (IMOD=160) will be
used.
No bounds checking has been implemented due to the fact that a vendor
may have violated the spec and would need to specify a value outside of
the max 8,000 IRQs/second limit specified in the xHCI spec.
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit dec08194ff.
Commit dec08194ff ("xhci: Limit USB2 port wake support for AMD Promontory
hosts") makes all high speed USB ports on ASUS PRIME B350M-A cease to
function after enabling runtime PM.
All boards with this chipsets will be affected, so revert the commit.
The original patch was added to stable 4.9, 4.11 and 4.12 and needs
to reverted from there as well
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Renesas uPD72020x XHCI controller seems to suffer from a really
annoying bug, where it may retain some of its DMA programming across a XHCI
reset, and despite the driver correctly programming new DMA addresses.
This is visible if the device has been using 64-bit DMA addresses, and is
then switched to using 32-bit DMA addresses. The top 32 bits of the
address (now zero) are ignored are replaced by the 32 bits from the
*previous* programming. Sticking with 64-bit DMA always works, but doesn't
seem very appropriate.
A PCI reset of the device restores the normal functionality, which is done
at probe time. Unfortunately, this has to be done before any quirk has
been discovered, hence the intrusive nature of the fix.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: stable@vger.kernel.org # v4.11+
When USB Ethernet is plugged in ASMEDIA ASM1042A xHCI host, bad
performance was manifesting in Web browser use (like download
large file such as ISO image). It is known limitation of
ASM1042A that is not compatible with driver scheduling,
As a workaround we can modify flow control handling of ASM1042A.
The register we modify is changes the behavior
[use quirk bit 28, usleep_range 40-60us, empty non-pci function -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiahau Chang <Lars_chang@asmedia.com.tw>
Signed-off-by: Ian Pilcher <arequipeno@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some remaining USB fixes for 4.13-rc1. They were originally
scheduled for 4.12-final, but I didn't send them to you in time.
Because of that, they were in a separate branch from the larger USB set
of patches, so here they are in a separate pull request.
Nothing major here a all, just 3 small patches:
- some usb-serial new device ids
- xhci bugfix for some crazy AMD hardware
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWV9FRg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylHxgCfTT31v4FaxH2k76qA1ZnHdXWHqyQAn3oyOE4T
uJhpp1FbFR1VNXM/jRox
=PCPm
-----END PGP SIGNATURE-----
Merge tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some remaining USB fixes for 4.13-rc1. They were originally
scheduled for 4.12-final, but I didn't send them to you in time.
Because of that, they were in a separate branch from the larger USB
set of patches, so here they are in a separate pull request.
Nothing major here a all, just three small patches:
- some usb-serial new device ids
- xhci bugfix for some crazy AMD hardware
All of these have been in linux-next for a long time with no reported
issues"
* tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Limit USB2 port wake support for AMD Promontory hosts
USB: serial: qcserial: new Sierra Wireless EM7305 device ID
USB: serial: option: add two Longcheer device ids
- introduce the new uuid_t/guid_t types that are going to replace
the somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS
and libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)
-----BEGIN PGP SIGNATURE-----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=J/4P
-----END PGP SIGNATURE-----
Merge tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid
Pull uuid subsystem from Christoph Hellwig:
"This is the new uuid subsystem, in which Amir, Andy and I have started
consolidating our uuid/guid helpers and improving the types used for
them. Note that various other subsystems have pulled in this tree, so
I'd like it to go in early.
UUID/GUID summary:
- introduce the new uuid_t/guid_t types that are going to replace the
somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS and
libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)"
* tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid: (34 commits)
ACPI: hns_dsaf_acpi_dsm_guid can be static
mmc: sdhci-pci: make guid intel_dsm_guid static
uuid: Take const on input of uuid_is_null() and guid_is_null()
thermal: int340x_thermal: fix compile after the UUID API switch
thermal: int340x_thermal: Switch to use new generic UUID API
acpi: always include uuid.h
ACPI: Switch to use generic guid_t in acpi_evaluate_dsm()
ACPI / extlog: Switch to use new generic UUID API
ACPI / bus: Switch to use new generic UUID API
ACPI / APEI: Switch to use new generic UUID API
acpi, nfit: Switch to use new generic UUID API
MAINTAINERS: add uuid entry
tmpfs: generate random sb->s_uuid
scsi_debug: switch to uuid_t
nvme: switch to uuid_t
sysctl: switch to use uuid_t
partitions/ldm: switch to use uuid_t
overlayfs: use uuid_t instead of uuid_be
fs: switch ->s_uuid to uuid_t
ima/policy: switch to use uuid_t
...
For AMD Promontory xHCI host, although you can disable USB 2.0 ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
This will disable wake on connect, disconnect and overcurrent on
AMD Promontory USB2 ports
[checkpatch cleanup and commit message reword -Mathias]
Cc: <stable@vger.kernel.org>
Cc: Tsai Nicholas <nicholas.tsai@amd.com>
Signed-off-by: Jiahau Chang <Lars_Chang@asmedia.com.tw>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When plugging an USB webcam I see the following message:
[106385.615559] xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[106390.583860] handle_tx_event: 913 callbacks suppressed
With this patch applied, I get no more printing of this message.
Cc: <stable@vger.kernel.org>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.
acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Intel Denverton microserver is Atom based and need the PME and CAS quirks
as well.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per [1] issue #4,
"The periodic EP scheduler always tries to schedule the EPs
that have large intervals (interval equal to or greater than
128 microframes) into different microframes. So it maintains
an internal counter and increments for each large interval
EP added. When the counter is greater than 128, the scheduler
rejects the new EP. So when the hub re-enumerated 128 times,
it triggers this condition."
This results in Bandwidth error when devices with periodic
endpoints (ISO/INT) having bInterval > 7 are plugged and
unplugged several times on a TUSB73x0 XHCI host.
Workaround this issue by limiting the bInterval to 7
(i.e. interval to 6) for High-speed or faster periodic endpoints.
[1] - http://www.ti.com/lit/er/sllz076/sllz076.pdf
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the unnecessary return line in xhci_pci_setup().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Apollo Lake also requires XHCI_PME_STUCK_QUIRK.
Adding its PCI ID to quirk.
Cc: <stable@vger.kernel.org>
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device is unplugged and replugged during Sx system suspend
some Intel xHC hosts will overwrite the CAS (Cold attach status) flag
and no device connection is noticed in resume.
A device in this state can be identified in resume if its link state
is in polling or compliance mode, and the current connect status is 0.
A device in this state needs to be warm reset.
Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
Observed on Cherryview and Apollolake as they go into compliance mode
if LFPS times out during polling, and re-plugged devices are not
discovered at resume.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC in Wildcatpoint-LP PCH is similar to LynxPoint-LP and need the
same quirks to prevent machines from spurious restart while
shutting them down.
Reported-by: Hasan Mahmood <hasan.mahm@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the hcd after checking for the xhci last quirks, not before.
This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the Linux PCI core does not touch power state of PCI bridges and
PCIe ports when system suspend is entered. Leaving them in D0 consumes
power unnecessarily and may prevent the CPU from entering deeper C-states.
With recent PCIe hardware we can power down the ports to save power given
that we take into account few restrictions:
- The PCIe port hardware is recent enough, starting from 2015.
- Devices connected to PCIe ports are effectively in D3cold once the port
is transitioned to D3 (the config space is not accessible anymore and
the link may be powered down).
- Devices behind the PCIe port need to be allowed to transition to D3cold
and back. There is a way both drivers and userspace can forbid this.
- If the device behind the PCIe port is capable of waking the system it
needs to be able to do so from D3cold.
This patch adds a new flag to struct pci_device called 'bridge_d3'. This
flag is set and cleared by the PCI core whenever there is a change in power
management state of any of the devices behind the PCIe port. When system
later on is suspended we only need to check this flag and if it is true
transition the port to D3 otherwise we leave it in D0.
Also provide override mechanism via command line parameter
"pcie_port_pm=[off|force]" that can be used to disable or enable the
feature regardless of the BIOS manufacturing date.
Tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I got one of these cards for testing uas with, it seems that with streams
it dma-s all over the place, corrupting memory. On my first tests it
managed to dma over the BIOS of the motherboard somehow and completely
bricked it.
Tests on another motherboard show that it does work with streams disabled.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will
remove the xhci controller from the PCI bus when the last USB device is
disconnected.
Add a flag to indicate that the host is being removed to avoid queueing
configure_endpoint commands for the dropped endpoints.
For PCI hotplugged controllers this will prevent 5 second command timeouts
For static xhci controllers the configure_endpoint command is not needed
in the removal case as everything will be returned, freed, and the
controller is reset.
For now the flag is only set for PCI connected host controllers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Broxton B0 also requires XHCI_PME_STUCK_QUIRK.
Adding PCI device ID for Broxton B and adding to quirk.
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Broxton M was verifed to require XHCI_PME_STUCK_QUIRK quirk as well.
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI_SSIC_PORT_UNUSED quirk was applied to the xHCI host controllers
in some Intel SoC chips. With this quirk applied, SSIC port is set
to "unused" prior to xhci_suspend(). This may cause problem if host
fails to suspend. In this case, the port is set to unused without
host further entering D3, and the port will not be usable anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two workarounds introduced by commit b8cb91e058 ("xhci: Workaround
for PME stuck issues in Intel xhci") and commit abce329c27 ("xhci:
Workaround to get D3 working in Intel xHCI") share a single quirk bit
XHCI_PME_STUCK_QUIRK. These two workarounds actually are different and
might happen on different hardwares. Need to separate them by adding a
quirk bit for the later.
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit abce329c27 ("xhci: Workaround to get D3 working in Intel xHCI")
adds a workaround for a limitation of PME storm caused by SSIC port in
some Intel SoCs. This commit only handled one SSIC port, while there
are actually two SSIC ports in the chips. This patch handles both SSIC
ports. Without this fix, users still see PME storm.
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a memory leak because acpi_evaluate_dsm() actually returns an
object which the caller is supposed to release. Fix this by calling
ACPI_FREE() for the returned object (this expands to kfree() so passing
NULL there is fine as well).
While there correct indentation in !CONFIG_ACPI case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.2
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch cleanups the hcd private size to suitable size.
The previous code has "sizeof(struct xhci_hcd *)" in xhci_hc_driver
as hcd_priv_size and sizeof(struct xhci_hcd) in xhci_plat_overrides
or xhci_pci_overrides as extra_priv_size. However, the xhci driver
uses a "sizeof(struct xhcd_hcd)" memory space in each hcd
(main_hcd and shared_hcd) actually.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We received several reports of systems rebooting and powering on
after an attempted shutdown. Testing showed that setting
XHCI_SPURIOUS_WAKEUP quirk in addition to the XHCI_SPURIOUS_REBOOT
quirk allowed the system to shutdown as expected for LynxPoint-LP
xHCI controllers. Set the quirk back.
Note that the quirk was originally introduced for LynxPoint and
LynxPoint-LP just for this same reason. See:
commit 638298dc66 ("xhci: Fix spurious wakeups after S5 on Haswell")
It was later limited to only concern HP machines as it caused
regression on some machines, see both bug and commit:
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66171
commit 6962d914f3 ("xhci: Limit the spurious wakeup fix only to HP machines")
Later it was discovered that the powering on after shutdown
was limited to LynxPoint-LP (Haswell-ULT) and that some non-LP HP
machine suffered from spontaneous resume from S3 (which should
not be related to the SPURIOUS_WAKEUP quirk at all). An attempt
to fix this then removed the SPURIOUS_WAKEUP flag usage completely.
commit b45abacde3 ("xhci: no switching back on non-ULT Haswell")
Current understanding is that LynxPoint-LP (Haswell ULT) machines
need the SPURIOUS_WAKEUP quirk, otherwise they will restart, and
plain Lynxpoint (Haswell) machines may _not_ have the quirk
set otherwise they again will restart.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Oliver Neukum <oneukum@suse.com>
[Added more history to commit message -Mathias]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the controller speed to HCD_USB31 to if host hardware supports USB 3.1
For PCI xhci controllers the USB 3.1 support is checked from SBRN bits in
pci config space. Platform controllers will need to set xhci->sbrn == 0x31
to indicate USB 3.1 support before calling xhci_gen_setup().
Also make sure xhci driver works correctly with speed set to HCD_USB31
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_pme_quirk() is only used when CONFIG_PM is defined.
Compiling a kernel without PM complains about this function
[reworded commit message -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Tomer Barletz <barletz@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI in Intel CherryView / Braswell Platform requires
a driver workaround to get xHCI D3 working. Without this
workaround, xHCI might not enter D3.
Workaround is to configure SSIC PORT as "unused" before D3
entry and "used" after D3 exit. This is done through a
vendor specific register (PORT2_SSIC_CONFIG_REG2 at offset
0x883c), in xhci suspend / resume callbacks.
Verified xHCI D3 works fine in CherryView / Braswell platform.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel xhci hw that require XHCI_PME_STUCK quirk have as default disabled
xhci from going to D3 state in runtime suspend. Driver needs to verify
it can deal with the hw by calling an ACPI _DSM method to get D3 enabled.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HCD core allocates memory for HCD private data in
usb_create_[shared_]hcd() so make use of that
mechanism to allocate the struct xhci_hcd.
Introduce struct xhci_driver_overrides to provide
the size of HCD private data and hc_driver operation
overrides. As of now we only need to override the
reset and start methods.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a device with an isochronous endpoint is plugged into the Intel
xHCI host controller, and the driver submits multiple frames per URB,
the xHCI driver will set the Block Event Interrupt (BEI) flag on all
but the last TD for the URB. This causes the host controller to place
an event on the event ring, but not send an interrupt. When the last
TD for the URB completes, BEI is cleared, and we get an interrupt for
the whole URB.
However, under Intel xHCI host controllers, if the event ring is full
of events from transfers with BEI set, an "Event Ring is Full" event
will be posted to the last entry of the event ring, but no interrupt
is generated. Host will cease all transfer and command executions and
wait until software completes handling the pending events in the event
ring. That means xHC stops, but event of "event ring is full" is not
notified. As the result, the xHC looks like dead to user.
This patch is to apply XHCI_AVOID_BEI quirk to Intel xHC devices. And
it should be backported to kernels as old as 3.0, that contains the
commit 69e848c209 ("Intel xhci: Support EHCI/xHCI port switching.").
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Alistair Grant <akgrant0710@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci in Intel Sunrisepoint and Cherryview platforms need a driver
workaround for a Stuck PME that might either block PME events in suspend,
or create spurious PME events preventing runtime suspend.
Workaround is to clear a internal PME flag, BIT(28) in a vendor specific
PMCTRL register at offset 0x80a4, in both suspend resume callbacks
Without this, xhci connected usb devices might never be able to wake up the
system from suspend, or prevent device from going to suspend (xhci d3)
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams do not work reliabe on Fresco Logic FL1000G xhci controllers,
trying to use them results in errors like this:
21:37:33 kernel: xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
21:37:33 kernel: xhci_hcd 0000:04:00.0: @00000000368b3570 9067b000 00000000 05000000 01078001
21:37:33 kernel: xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
21:37:33 kernel: xhci_hcd 0000:04:00.0: @00000000368b3580 9067b400 00000000 05000000 01038001
As always I've ordered a pci-e addon card with a Fresco Logic controller for
myself to see if I can come up with a better fix then the big hammer, in
the mean time this will make uas devices work again (in usb-storage mode)
for FL1000G users.
Reported-by: Marcin Zajączkowski <mszpak@wp.pl>
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When system is being suspended, if host device is not allowed to do wakeup,
xhci_suspend() needs to clear all root port wake on bits. Otherwise, some
platforms may generate spurious wakeup, even if PCI PME# is disabled.
The initial commit ff8cbf250b ("xhci: clear root port wake on bits"),
which also got into stable, turned out to not work correctly and had to
be reverted, and is now rewritten.
Cc: stable <stable@vger.kernel.org> # v3.2+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[Mathias Nyman: reword commit message]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch back is limited to ULT even on HP. The contrary
finding arose by bad luck in BIOS versions for testing.
This fixes spontaneous resume from S3 on some HP laptops.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk
which is known to work fine with other controllers causes the system to freeze
when connected over usb-3 with this controller, where as it works fine with
uas in usb-2 ports, indicating a problem with streams.
This is a bit bigger hammer then I would like to use for this, but for now it
will have to make do. I've ordered a pci-e usb controller card with an Asmedia
1042, once that arrives I'll try to get streams to work (with a quirk flag if
necessary) and then we can re-enable them. For now this at least makes uas
capable disk enclosures work again by forcing fallback to the usb-storage
driver.
Reported-by: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of building all of the xHCI code into a single module, separate
it out into the core (xhci-hcd), PCI (xhci-pci, now selected by the new
config option CONFIG_USB_XHCI_PCI), and platform (xhci-plat) drivers.
Also update the PCI/platform drivers with module descriptions/licenses
and have them register their respective drivers in their initcalls.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
