- Use ida_alloc() instead of deprecated ida_simple_get() (Christophe JAILLET)
* pci/controller/vmd:
PCI: vmd: Remove usage of the deprecated ida_simple_xx() API
- Replace of_device.h with explicit of.h include to untangle header usage
(Rob Herring)
- Add DT and driver support for optional miniPCIe 1.5v and 3.3v regulators
on KingFisher (Wolfram Sang)
* pci/controller/rcar:
PCI: rcar-host: Add support for optional regulators
dt-bindings: PCI: rcar-pci-host: Add optional regulators
PCI: rcar-gen4: Replace of_device.h with explicit of.h include
- Clear MSI interrupt status before handler to avoid missing MSIs that
occur after the handler (qizhong cheng)
- Update mediatek-gen3 translation window setup to handle MMIO space that
is not a power of two in size (Jianjun Wang)
* pci/controller/mediatek:
PCI: mediatek-gen3: Fix translation window size calculation
PCI: mediatek: Clear interrupt status before dispatching handler
- Add suspend/resume support for Layerscape LS1043a, including
software-managed PME_Turn_Off and transitions between L0, L2/L3_Ready
Link states (Frank Li)
* pci/controller/layerscape:
PCI: layerscape: Add suspend/resume for ls1043a
PCI: layerscape(ep): Rename pf_* as pf_lut_*
PCI: layerscape: Add suspend/resume for ls1021a
PCI: layerscape: Add function pointer for exit_from_l2()
- Use devm_kasprintf() to dynamically allocate clock names, removing need
for an intermediate buffer (Christophe JAILLET)
* pci/controller/kirin:
PCI: kirin: Use devm_kasprintf() to dynamically allocate clock names
- Hold power management references to all PHYs while enabling them to avoid
a race when one provides clocks to others (Siddharth Vadapalli)
* pci/controller/keystone:
PCI: keystone: Fix race condition when initializing PHYs
- Add j721e DT and driver support for 'num-lanes' for devices that support
x1, x2, or x4 Links (Matt Ranostay)
- Add j721e DT compatible strings and driver support for j784s4 (Matt Ranostay)
- Make TI J721E Kconfig depend on ARCH_K3 since the hardware is specific to
those TI SoC parts (Peter Robinson)
* pci/controller/cadence:
PCI: j721e: Make TI J721E depend on ARCH_K3
PCI: j721e: Add TI J784S4 PCIe configuration
PCI: j721e: Add PCIe 4x lane selection support
PCI: j721e: Add per platform maximum lane settings
dt-bindings: PCI: ti,j721e-pci-*: Add j784s4-pci-* compatible strings
dt-bindings: PCI: ti,j721e-pci-*: Add checks for num-lanes
The Broadcom STB/CM PCIe HW core, which is also used in RPi SOCs, must be
deliberately set by the PCIe RC HW into one of three mutually exclusive
modes:
"safe" -- No CLKREQ# expected or required, refclk is always provided. This
mode should work for all devices but is not be capable of any refclk
power savings.
"no-l1ss" -- CLKREQ# is expected to be driven by the downstream device for
CPM and ASPM L0s and L1. Provides Clock Power Management, L0s, and L1,
but cannot provide L1 substate (L1SS) power savings. If the downstream
device connected to the RC is L1SS capable AND the OS enables L1SS, all
PCIe traffic may abruptly halt, potentially hanging the system.
"default" -- Bidirectional CLKREQ# between the RC and downstream device.
Provides ASPM L0s, L1, and L1SS, but not compliant to provide Clock
Power Management; specifically, may not be able to meet the T_CLRon max
timing of 400ns as specified in "Dynamic Clock Control", section
3.2.5.2.2 of the PCIe Express Mini CEM 2.1 specification. This
situation is atypical and should happen only with older devices.
Previously, this driver always set the mode to "no-l1ss", as almost all
STB/CM boards operate in this mode. But now there is interest in
activating L1SS power savings from STB/CM customers, which requires "aspm"
mode. In addition, a bug was filed for RPi4 CM platform because most
devices did not work in "no-l1ss" mode.
Note that the mode is specified by the DT property "brcm,clkreq-mode". If
this property is omitted, then "default" mode is chosen.
Note: Since L1 substates are now possible, a modification was made
regarding an internal bus timeout: During long periods of the PCIe RC HW
being in an L1SS sleep state, there may be a timeout on an internal bus
access, even though there may not be any PCIe access involved. Such a
timeout will cause a subsequent CPU abort.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217276
Link: https://lore.kernel.org/linux-pci/20231113185607.1756-3-james.quinlan@broadcom.com
Tested-by: Cyril Brulebois <cyril@debamax.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
When using the fls() helper, the translation table should be a power of
two; otherwise, the resulting value will not be correct.
For example, given fls(0x3e00000) - 1 = 25, the PCIe translation window
size will be set to 0x2000000 instead of the expected size 0x3e00000.
Fix the translation window by splitting the MMIO space into multiple tables
if its size is not a power of two.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231023081423.18559-1-jianjun.wang@mediatek.com
Fixes: d3bf75b579 ("PCI: mediatek-gen3: Add MediaTek Gen3 driver for MT8192")
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
We found a failure when using the iperf tool during WiFi performance
testing, where some MSIs were received while clearing the interrupt
status, and these MSIs cannot be serviced.
The interrupt status can be cleared even if the MSI status remains pending.
As such, given the edge-triggered interrupt type, its status should be
cleared before being dispatched to the handler of the underling device.
[kwilczynski: commit log, code comment wording]
Link: https://lore.kernel.org/linux-pci/20231211094923.31967-1-jianjun.wang@mediatek.com
Fixes: 43e6409db6 ("PCI: mediatek: Add MSI support for MT2712 and MT7622")
Signed-off-by: qizhong cheng <qizhong.cheng@mediatek.com>
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: rewrap comment]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: <stable@vger.kernel.org>
The PCI driver invokes the PHY APIs using the ks_pcie_enable_phy()
function. The PHY in this case is the Serdes. It is possible that the
PCI instance is configured for two lane operation across two different
Serdes instances, using one lane of each Serdes.
In such a configuration, if the reference clock for one Serdes is
provided by the other Serdes, it results in a race condition. After the
Serdes providing the reference clock is initialized by the PCI driver by
invoking its PHY APIs, it is not guaranteed that this Serdes remains
powered on long enough for the PHY APIs based initialization of the
dependent Serdes. In such cases, the PLL of the dependent Serdes fails
to lock due to the absence of the reference clock from the former Serdes
which has been powered off by the PM Core.
Fix this by obtaining reference to the PHYs before invoking the PHY
initialization APIs and releasing reference after the initialization is
complete.
Link: https://lore.kernel.org/linux-pci/20230927041845.1222080-1-s-vadapalli@ti.com
Fixes: 49229238ab ("PCI: keystone: Cleanup PHY handling")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Currently, if the function irq_domain_add_linear() fails to allocate
a new IRQ domain and returns NULL, we would then still return a success
from the xilinx_pl_dma_pcie_init_irq_domain() function regardless, as
the PTR_ERR(NULL) would return a value of zero. This is not a desirable
outcome.
Thus, fix the incorrect error code and return the -ENOMEM error code if
the irq_domain_add_linear() fails to allocate a new IRQ domain.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231030072757.3236546-1-harshit.m.mogalapalli@oracle.com
Fixes: 8d786149d7 ("PCI: xilinx-xdma: Add Xilinx XDMA Root Port driver")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The error paths that follow calls to the devm_request_irq() functions
within the xilinx_pl_dma_pcie_setup_irq() reference an uninitialized
symbol each that also so happens to be incorrect.
Thus, fix this omission and reference the correct variable when invoking
a given dev_err() function following an error.
This problem was found using smatch via the 0-DAY CI Kernel Test service:
drivers/pci/controller/pcie-xilinx-dma-pl.c:638 xilinx_pl_dma_pcie_setup_irq() error: uninitialized symbol 'irq'.
drivers/pci/controller/pcie-xilinx-dma-pl.c:645 xilinx_pl_dma_pcie_setup_irq() error: uninitialized symbol 'irq'.
Fixes: 8d786149d7 ("PCI: xilinx-xdma: Add Xilinx XDMA Root Port driver")
Link: https://lore.kernel.org/oe-kbuild/202312120248.5DblxkBp-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202312120248.5DblxkBp-lkp@intel.com/
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
When building with clang 18 with the -Werror compiler option enabled,
the following error will be reported:
drivers/pci/controller/dwc/pcie-rcar-gen4.c:439:15: error: cast to smaller integer type 'enum dw_pcie_device_mode' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
439 | rcar->mode = (enum dw_pcie_device_mode)of_device_get_match_data(&rcar->pdev->dev);
To fix this issue, cast the data the of_device_get_match_data() helper
returns to uintptr_t rather than the dw_pcie_device_mode enum.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-7-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
When building with clang 18, the following warning will be reported:
drivers/pci/controller/pcie-iproc-platform.c:54:15: warning: cast to smaller integer type 'enum iproc_pcie_type' from 'const void *' [-Wvoid-pointer-to-enum-cast]
55 | pcie->type = (enum iproc_pcie_type) of_device_get_match_data(dev);
To fix this issue, cast the data the of_device_get_match_data() helper
returns to uintptr_t rather than the iproc_pcie_type enum.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-6-yoshihiro.shimoda.uh@renesas.com
Link: https://github.com/ClangBuiltLinux/linux/issues/1910
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The current code calculated some dbi[2] registers' offset by calling
dw_pcie_ep_get_dbi[2]_offset() in each function. To improve the code
readability, add dw_pcie_ep_{read,write}_dbi[2} and some data-width
related helpers.
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-5-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Since the struct member .func_conf_select makes the intentions behind it
difficult to ascertain from its name alone, rename it to .get_dbi_offset
to make the intended usage more obvious.
[kwilczynski: commmit log]
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Since the name of the dw_pcie_ep_ops struct makes it obvious that it's
for the PCIe Endpoint, rename the struct member .ep_init to .init.
[kwilczynski: commit log]
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Srikanth Thokala <srikanth.thokala@intel.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Since the name of the dw_pcie_host_ops struct makes it obvious that it's
for the PCIe Host, drop the host prefix from the struct members.
[kwilczynski: commit log]
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Lei Chuanhua <lchuanhua@maxlinear.com>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
The J721E PCIe is hardware specific to TI SoC parts so add a dependency
on that so it's available for those SoC parts and for compile testing but
not necessarily everyone who enables the Cadence PCIe controller.
Link: https://lore.kernel.org/linux-pci/20240104213910.1426843-1-pbrobinson@gmail.com
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
In the xilinx-nwl controller driver, change all use of "legacy" and
"leg" to "intx", to match the term used in the PCI specifications.
Link: https://lore.kernel.org/r/20231122060406.14695-17-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Rename the function rockchip_pcie_legacy_int_handler() of the rockchip
host driver to rockchip_pcie_intx_handler() to match the PCI_IRQ_INTX
macro name used to control this function execution, and to match the
term used in the PCI specifications.
Link: https://lore.kernel.org/r/20231122060406.14695-16-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Rename the function rockchip_pcie_ep_send_legacy_irq() of the rockchip
endpoint driver to rockchip_pcie_ep_send_intx_irq(). Uses of the term
"legacy" are also replaced with "INTX" in comments.
Link: https://lore.kernel.org/r/20231122060406.14695-15-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In the Designware uniphier controller driver, including the endpoint
driver, change all names using "legacy" to use "intx", to match the
term used in the PCI specifications.
Link: https://lore.kernel.org/r/20231122060406.14695-14-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In the Designware tegra194 controller driver, change all names using
"legacy" to use "intx", to match the term used in the PCI
specifications.
Link: https://lore.kernel.org/r/20231122060406.14695-13-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Rename the function rockchip_pcie_legacy_int_handler() to
rockchip_pcie_intx_handler() to match the code managing INTX interrupts
(e.g. intx_domain_ops) and the term used in the PCI specifications.
Link: https://lore.kernel.org/r/20231122060406.14695-12-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In the Keystone controller driver, change all names using "legacy" to
use "intx" instead, to match the term used in the PCI specifications.
Given that the field legacy_intc_np of struct keystone_pcie is unused,
this field is removed instead of being renamed.
Link: https://lore.kernel.org/r/20231122060406.14695-11-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Rename the function dw_pcie_ep_raise_legacy_irq() of the Designware
endpoint controller driver to dw_pcie_ep_raise_intx_irq() to match the
name of the PCI_IRQ_INTX macro.
Link: https://lore.kernel.org/r/20231122060406.14695-10-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In the Cadence endpoint controller driver, rename the function
cdns_pcie_ep_send_legacy_irq() to cdns_pcie_ep_send_intx_irq() to match
the macro PCI_IRQ_INTX name. Related comments and messages mentioning
"legacy" are also changed to refer to "intx".
Link: https://lore.kernel.org/r/20231122060406.14695-9-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Rename the function dra7xx_pcie_raise_legacy_irq() to
dra7xx_pcie_raise_intx_irq() to match the use of the PCI_IRQ_INTX macro.
Link: https://lore.kernel.org/r/20231122060406.14695-8-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
linux/pci.h defines the IRQ flags PCI_IRQ_INTX, PCI_IRQ_MSI and
PCI_IRQ_MSIX. Let's use these flags directly instead of the endpoint
definitions provided by enum pci_epc_irq_type. This removes the need
for defining this enum type completely.
Link: https://lore.kernel.org/r/20231122060406.14695-3-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is no need to call the dev_err() function directly to print a
custom message when handling an error from either the platform_get_irq()
or platform_get_irq_byname() functions as both are going to display an
appropriate error message in case of a failure.
./drivers/pci/controller/pcie-xilinx-dma-pl.c:688:2-9: line 688 is redundant because platform_get_irq() already prints an error
./drivers/pci/controller/pcie-xilinx-dma-pl.c:702:2-9: line 702 is redundant because platform_get_irq() already prints an error
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=7074
Link: https://lore.kernel.org/linux-pci/20231030061242.51475-1-yang.lee@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Commit 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get
correct MSI-X table address") modified dw_pcie_ep_raise_msix_irq() to
support iATUs which require a specific alignment.
However, this support cannot have been properly tested.
The whole point is for the iATU to map an address that is aligned,
using dw_pcie_ep_map_addr(), and then let the writel() write to
ep->msi_mem + aligned_offset.
Thus, modify the address that is mapped such that it is aligned.
With this change, dw_pcie_ep_raise_msix_irq() matches the logic in
dw_pcie_ep_raise_msi_irq().
Link: https://lore.kernel.org/linux-pci/20231128132231.2221614-1-nks@flawful.org
Fixes: 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # 5.7
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Use devm_kasprintf() instead of open coding it. This saves the need of
an intermediate buffer.
There was also no reason to use devm_kstrdup_const() as string is known
to be constant.
[kwilczynski: commit log, and add missing Reviewed-by tag]
Link: https://lore.kernel.org/linux-pci/1bad6879083a7d836c8a47418a0afa22485e8f69.1700294127.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Link: https://lore.kernel.org/linux-pci/c3a51791d54deaa818b8526975fc4e16ef1090ce.1701682617.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Link: https://lore.kernel.org/linux-pci/06612aff79dfb52d5b0b20129dff5e4b1f04d3a7.1701682617.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Link: https://lore.kernel.org/linux-pci/50de44ea8931465fd9cdc821854ea761cb43adf6.1701682617.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
As part of converting RISC-V SOC_FOO symbols to ARCH_FOO to match the
use of such symbols on other architectures, convert the SiFive PCI
drivers to use the newer symbol.
Link: https://lore.kernel.org/linux-pci/20230918-safeness-cornflake-62278bc3aaaa@wendy
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The KingFisher board has regulators for miniPCIe, so enable these
optional regulators using devm. devm will automatically disable them
when the driver releases the device. Order variables in reverse-xmas
while we are here.
[kwilczynski: update style to match rest of the code]
Link: https://lore.kernel.org/linux-pci/20231105092908.3792-3-wsa+renesas@sang-engineering.com
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it was merged into the regular platform
bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h.
As a result, there's a pretty much random mix of those include files
used throughout the tree. In order to detangle these headers and replace
the implicit includes with struct declarations, users need to explicitly
include the correct includes.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231207165251.2855783-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Add support for setting of two-bit field that allows selection of 4x lane
PCIe which was previously limited to only 2x lanes.
Link: https://lore.kernel.org/linux-pci/20231128054402.2155183-5-s-vadapalli@ti.com
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Achal Verma <a-verma1@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Various platforms have different maximum amount of lanes that can be
selected. Add max_lanes to struct j721e_pcie to allow for detection of this
which is needed to calculate the needed bitmask size for the possible lane
count.
Link: https://lore.kernel.org/linux-pci/20231128054402.2155183-4-s-vadapalli@ti.com
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Achal Verma <a-verma1@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Add suspend/resume support for Layerscape LS1043a.
In the suspend path, PME_Turn_Off message is sent to the endpoint to
transition the link to L2/L3_Ready state. In this SoC, there is no way to
check if the controller has received the PME_To_Ack from the endpoint or
not. So to be on the safer side, the driver just waits for
PCIE_PME_TO_L2_TIMEOUT_US before asserting the SoC specific PMXMTTURNOFF
bit to complete the PME_Turn_Off handshake. Then the link would enter L2/L3
state depending on the VAUX supply.
In the resume path, the link is brought back from L2 to L0 by doing a
software reset.
Link: https://lore.kernel.org/r/20231204160829.2498703-5-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
'pf' and 'lut' are two different acronyms describing the same
thing, basically it is a MMIO base address plus an offset.
Rename them to avoid duplicate pf_* and lut_* naming schemes in the
driver.
Link: https://lore.kernel.org/r/20231204160829.2498703-4-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
Add suspend/resume support for Layerscape LS1021a.
In the suspend path, PME_Turn_Off message is sent to the endpoint to
transition the link to L2/L3_Ready state. In this SoC, there is no way to
check if the controller has received the PME_To_Ack from the endpoint or
not. So to be on the safer side, the driver just waits for
PCIE_PME_TO_L2_TIMEOUT_US before asserting the SoC specific PMXMTTURNOFF
bit to complete the PME_Turn_Off handshake. Then the link would enter L2/L3
state depending on the VAUX supply.
In the resume path, the link is brought back from L2 to L0 by doing a
software reset.
Link: https://lore.kernel.org/r/20231204160829.2498703-3-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
Since different SoCs require different sequences for exiting L2, let's add
a separate "exit_from_l2()" callback to handle SoC specific sequences.
Change ls_pcie_exit_from_l2() return value from void to int in order
to propagate errors. Return an error if the exit_from_l2() callback
fails in the resume flow.
Link: https://lore.kernel.org/r/20231204160829.2498703-2-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
Break up the newly added ASPM comment so that it fits within the soft 80
character limit and becomes more readable.
Link: https://lore.kernel.org/r/20231128081512.19387-5-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The qcom_pcie_enable_aspm() helper is called from pci_walk_bus() during
host init to enable ASPM.
Since pci_walk_bus() already holds a pci_bus_sem read lock, use
pci_enable_link_state_locked() to enable link states in order to avoid a
potential deadlock (e.g. in case someone takes a write lock before
reacquiring the read lock).
This issue was reported by lockdep:
============================================
WARNING: possible recursive locking detected
6.7.0-rc1 #4 Not tainted
--------------------------------------------
kworker/u16:6/147 is trying to acquire lock:
ffffbf3ff9d2cfa0 (pci_bus_sem){++++}-{3:3}, at: pci_enable_link_state+0x74/0x1e8
but task is already holding lock:
ffffbf3ff9d2cfa0 (pci_bus_sem){++++}-{3:3}, at: pci_walk_bus+0x34/0xbc
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(pci_bus_sem);
lock(pci_bus_sem);
*** DEADLOCK ***
Fixes: 9f4f3dfad8 ("PCI: qcom: Enable ASPM for platforms supporting 1.9.0 ops")
Link: https://lore.kernel.org/r/20231128081512.19387-4-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
[bhelgaas: add "potential" in subject since the deadlock has only been
reported by lockdep, include helper name in commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The vmd_pm_enable_quirk() helper is called from pci_walk_bus() during
probe to enable ASPM for controllers with VMD_FEAT_BIOS_PM_QUIRK set.
Since pci_walk_bus() already holds a pci_bus_sem read lock, use
pci_enable_link_state_locked() to enable link states in order to avoid a
potential deadlock (e.g. in case someone takes a write lock before
reacquiring the read lock).
Fixes: f492edb40b ("PCI: vmd: Add quirk to configure PCIe ASPM and LTR")
Link: https://lore.kernel.org/r/20231128081512.19387-3-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
[bhelgaas: add "potential" in subject since the deadlock has only been
reported by lockdep, include helper name in commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 6.3
Cc: Michael Bottini <michael.a.bottini@linux.intel.com>
Cc: David E. Box <david.e.box@linux.intel.com>
This is a partial revert of 8b3517f88f ("PCI: loongson: Prevent LS7A MRRS
increases") for MIPS-based Loongson.
Some MIPS Loongson systems don't support arbitrary Max_Read_Request_Size
(MRRS) settings. 8b3517f88f ("PCI: loongson: Prevent LS7A MRRS
increases") worked around that by (1) assuming that firmware configured
MRRS to the maximum supported value and (2) preventing the PCI core from
increasing MRRS.
Unfortunately, some firmware doesn't set that maximum MRRS correctly, which
results in devices not being initialized correctly. One symptom, from the
Debian report below, is this:
ata4.00: exception Emask 0x0 SAct 0x20000000 SErr 0x0 action 0x6 frozen
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/20:e8:00:f0:e1/00:00:00:00:00/40 tag 29 ncq dma 16384 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
Limit MRRS to 256 because MIPS Loongson with higher MRRS support is
considered rare.
This must be done at device enablement stage because the MRRS setting may
get lost if PCI_COMMAND_MASTER on the parent bridge is cleared, and we are
only sure parent bridge is enabled at this point.
Fixes: 8b3517f88f ("PCI: loongson: Prevent LS7A MRRS increases")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217680
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1035587
Link: https://lore.kernel.org/r/20231201115028.84351-1-jiaxun.yang@flygoat.com
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Cc: stable@vger.kernel.org
This field is set to APIC_DELIVERY_MODE_FIXED in all cases, and is read
exactly once. Fold the constant in uv_program_mmr() and drop the field.
Searching for the origin of the stale HyperV comment reveals commit
a31e58e129 ("x86/apic: Switch all APICs to Fixed delivery mode") which
notes:
As a consequence of this change, the apic::irq_delivery_mode field is
now pointless, but this needs to be cleaned up in a separate patch.
6 years is long enough for this technical debt to have survived.
[ bp: Fold in
https://lore.kernel.org/r/20231121123034.1442059-1-andrew.cooper3@citrix.com
]
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Link: https://lore.kernel.org/r/20231102-x86-apic-v1-1-bf049a2a0ed6@citrix.com
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
pci_host_common_remove() returned zero unconditionally. With that converted
to return void instead, the generic pci host driver can be switched to
.remove_new() trivially.
Link: https://lore.kernel.org/r/20231020092107.2148311-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will@kernel.org>
-----BEGIN PGP SIGNATURE-----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=G//C
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Use acpi_evaluate_dsm_typed() instead of open-coding _DSM
evaluation to learn device characteristics (Andy Shevchenko)
- Tidy multi-function header checks using new PCI_HEADER_TYPE_MASK
definition (Ilpo Järvinen)
- Simplify config access error checking in various drivers (Ilpo
Järvinen)
- Use pcie_capability_clear_word() (not
pcie_capability_clear_and_set_word()) when only clearing (Ilpo
Järvinen)
- Add pci_get_base_class() to simplify finding devices using base
class only (ignoring subclass and programming interface) (Sui
Jingfeng)
- Add pci_is_vga(), which includes ancient PCI_CLASS_NOT_DEFINED_VGA
devices from before the Class Code was added to PCI (Sui Jingfeng)
- Use pci_is_vga() for vgaarb, sysfs "boot_vga", virtio, qxl to
include ancient VGA devices (Sui Jingfeng)
Resource management:
- Make pci_assign_unassigned_resources() non-init because sparc uses
it after init (Randy Dunlap)
Driver binding:
- Retain .remove() and .probe() callbacks (previously __init) because
sysfs may cause them to be called later (Uwe Kleine-König)
- Prevent xHCI driver from claiming AMD VanGogh USB3 DRD device, so
it can be claimed by dwc3 instead (Vicki Pfau)
PCI device hotplug:
- Add Ampere Altra Attention Indicator extension driver for acpiphp
(D Scott Phillips)
Power management:
- Quirk VideoPropulsion Torrent QN16e with longer delay after reset
(Lukas Wunner)
- Prevent users from overriding drivers that say we shouldn't use
D3cold (Lukas Wunner)
- Avoid PME from D3hot/D3cold for AMD Rembrandt and Phoenix USB4
because wakeup interrupts from those states don't work if amd-pmc
has put the platform in a hardware sleep state (Mario Limonciello)
IOMMU:
- Disable ATS for Intel IPU E2000 devices with invalidation message
endianness erratum (Bartosz Pawlowski)
Error handling:
- Factor out interrupt enable/disable into helpers (Kai-Heng Feng)
Peer-to-peer DMA:
- Fix flexible-array usage in struct pci_p2pdma_pagemap in case we
ever use pagemaps with multiple entries (Gustavo A. R. Silva)
ASPM:
- Revert a change that broke when drivers disabled L1 and users later
enabled an L1.x substate via sysfs, and fix a similar issue when
users disabled L1 via sysfs (Heiner Kallweit)
Endpoint framework:
- Fix double free in __pci_epc_create() (Dan Carpenter)
- Use IS_ERR_OR_NULL() to simplify endpoint core (Ruan Jinjie)
Cadence PCIe controller driver:
- Drop unused "is_rc" member (Li Chen)
Freescale Layerscape PCIe controller driver:
- Enable 64-bit addressing in endpoint mode (Guanhua Gao)
Intel VMD host bridge driver:
- Fix multi-function header check (Ilpo Järvinen)
Microsoft Hyper-V host bridge driver:
- Annotate struct hv_dr_state with __counted_by (Kees Cook)
NVIDIA Tegra194 PCIe controller driver:
- Drop setting of LNKCAP_MLW (max link width) since dw_pcie_setup()
already does this via dw_pcie_link_set_max_link_width() (Yoshihiro
Shimoda)
Qualcomm PCIe controller driver:
- Use PCIE_SPEED2MBS_ENC() to simplify encoding of link speed
(Manivannan Sadhasivam)
- Add a .write_dbi2() callback so DBI2 register writes, e.g., for
setting the BAR size, work correctly (Manivannan Sadhasivam)
- Enable ASPM for platforms that use 1.9.0 ops, because the PCI core
doesn't enable ASPM states that haven't been enabled by the
firmware (Manivannan Sadhasivam)
Renesas R-Car Gen4 PCIe controller driver:
- Add DesignWare core support (set max link width, EDMA_UNROLL flag,
.pre_init(), .deinit(), etc) for use by R-Car Gen4 driver
(Yoshihiro Shimoda)
- Add driver and DT schema for DesignWare-based Renesas R-Car Gen4
controller in both host and endpoint mode (Yoshihiro Shimoda)
Xilinx NWL PCIe controller driver:
- Update ECAM size to support 256 buses (Thippeswamy Havalige)
- Stop setting bridge primary/secondary/subordinate bus numbers,
since PCI core does this (Thippeswamy Havalige)
Xilinx XDMA controller driver:
- Add driver and DT schema for Zynq UltraScale+ MPSoCs devices with
Xilinx XDMA Soft IP (Thippeswamy Havalige)
Miscellaneous:
- Use FIELD_GET()/FIELD_PREP() to simplify and reduce use of _SHIFT
macros (Ilpo Järvinen, Bjorn Helgaas)
- Remove logic_outb(), _outw(), outl() duplicate declarations (John
Sanpe)
- Replace unnecessary UTF-8 in Kconfig help text because menuconfig
doesn't render it correctly (Liu Song)"
* tag 'pci-v6.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (102 commits)
PCI: qcom-ep: Add dedicated callback for writing to DBI2 registers
PCI: Simplify pcie_capability_clear_and_set_word() to ..._clear_word()
PCI: endpoint: Fix double free in __pci_epc_create()
PCI: xilinx-xdma: Add Xilinx XDMA Root Port driver
dt-bindings: PCI: xilinx-xdma: Add schemas for Xilinx XDMA PCIe Root Port Bridge
PCI: xilinx-cpm: Move IRQ definitions to a common header
PCI: xilinx-nwl: Modify ECAM size to enable support for 256 buses
PCI: xilinx-nwl: Rename the NWL_ECAM_VALUE_DEFAULT macro
dt-bindings: PCI: xilinx-nwl: Modify ECAM size in the DT example
PCI: xilinx-nwl: Remove redundant code that sets Type 1 header fields
PCI: hotplug: Add Ampere Altra Attention Indicator extension driver
PCI/AER: Factor out interrupt toggling into helpers
PCI: acpiphp: Allow built-in drivers for Attention Indicators
PCI/portdrv: Use FIELD_GET()
PCI/VC: Use FIELD_GET()
PCI/PTM: Use FIELD_GET()
PCI/PME: Use FIELD_GET()
PCI/ATS: Use FIELD_GET()
PCI/ATS: Show PASID Capability register width in bitmasks
PCI/ASPM: Fix L1 substate handling in aspm_attr_store_common()
...
- Use FIELD_GET()/FIELD_PREP() when possible throughout drivers/pci/ (Ilpo
Järvinen, Bjorn Helgaas)
- Rework DPC control programming for clarity (Ilpo Järvinen)
* pci/field-get:
PCI/portdrv: Use FIELD_GET()
PCI/VC: Use FIELD_GET()
PCI/PTM: Use FIELD_GET()
PCI/PME: Use FIELD_GET()
PCI/ATS: Use FIELD_GET()
PCI/ATS: Show PASID Capability register width in bitmasks
PCI: Use FIELD_GET() in Sapphire RX 5600 XT Pulse quirk
PCI: Use FIELD_GET()
PCI/MSI: Use FIELD_GET/PREP()
PCI/DPC: Use defines with DPC reason fields
PCI/DPC: Use defined fields with DPC_CTL register
PCI/DPC: Use FIELD_GET()
PCI: hotplug: Use FIELD_GET/PREP()
PCI: dwc: Use FIELD_GET/PREP()
PCI: cadence: Use FIELD_GET()
PCI: Use FIELD_GET() to extract Link Width
PCI: mvebu: Use FIELD_PREP() with Link Width
PCI: tegra194: Use FIELD_GET()/FIELD_PREP() with Link Width fields
# Conflicts:
# drivers/pci/controller/dwc/pcie-tegra194.c
- Simplify config accessor error checking (Ilpo Järvinen)
* pci/config-errs:
scsi: ipr: Do PCI error checks on own line
PCI: xgene: Do PCI error check on own line & keep return value
PCI: Do error check on own line to split long "if" conditions
atm: iphase: Do PCI error checks on own line
sh: pci: Do PCI error check on own line
alpha: Streamline convoluted PCI error handling
- Move Xilinx IRQ definitions to a common header shared by pcie-xilinx-cpm
and xilinx-xdma (Thippeswamy Havalige)
- Add Xilinx XDMA driver and DT schema (Thippeswamy Havalige)
* pci/controller/xilinx-xdma:
PCI: xilinx-xdma: Add Xilinx XDMA Root Port driver
dt-bindings: PCI: xilinx-xdma: Add schemas for Xilinx XDMA PCIe Root Port Bridge
PCI: xilinx-cpm: Move IRQ definitions to a common header
- Drop xilinx-nwl updates of bridge bus number fields, since PCI core
already does that (Thippeswamy Havalige)
- Update xilinx-nwl driver and ECAM size in devicetree example to allow up
to 256 buses (Thippeswamy Havalige)
* pci/controller/xilinx-ecam:
PCI: xilinx-nwl: Modify ECAM size to enable support for 256 buses
PCI: xilinx-nwl: Rename the NWL_ECAM_VALUE_DEFAULT macro
dt-bindings: PCI: xilinx-nwl: Modify ECAM size in the DT example
PCI: xilinx-nwl: Remove redundant code that sets Type 1 header fields
- Use PCIE_SPEED2MBS_ENC() macro in qcom host and endpoint to encode link
speed instead of hard-coding the link speed in MBps (Manivannan
Sadhasivam)
- Use Mbps_to_icc() (not MBps_to_icc()) in tegra194 instead of explicitly
doing the bytes-to-bits conversion (Manivannan Sadhasivam)
* pci/controller/speed:
PCI: tegra194: Use Mbps_to_icc() macro for setting icc speed
PCI: qcom-ep: Use PCIE_SPEED2MBS_ENC() macro for encoding link speed
PCI: qcom: Use PCIE_SPEED2MBS_ENC() macro for encoding link speed
- Add generic T_PVPERL macro for the required interval between power being
stable and PERST# being inactive (Yoshihiro Shimoda)
- Factor out dw_pcie_link_set_max_link_width() (Yoshihiro Shimoda)
- Update PCI_EXP_LNKCAP_MLW so Link Capabilities shows the correct max link
width (Yoshihiro Shimoda)
- Drop tegra194 PCI_EXP_LNKCAP_MLW setting since dw_pcie_setup() already
does it (Yoshihiro Shimoda)
- Add dwc support for different dbi and dbi2 register offsets, to be used
for R-Car Gen4 controllers (Yoshihiro Shimoda)
- Add EDMA_UNROLL capability flag for R-Car Gen4 controllers that don't
correctly advertise unrolled mapping via their eDMA CTRL register
(Yoshihiro Shimoda)
- Export dw_pcie_ep_exit() for use by the modular R-Car Gen4 driver
(Yoshihiro Shimoda)
- Add .pre_init() and .deinit() hooks for use by R-Car Gen4 controllers
(Yoshihiro Shimoda)
- Increase snps,dw-pcie DT reg and reg-names maxItems for R-Car Gen4
controllers (Yoshihiro Shimoda)
- Add rcar-gen4-pci host and endpoint DT bindings and drivers (Yoshihiro
Shimoda)
- Add Renesas R8A779F0 Device ID to pci_endpoint_test to allow testing on
R-Car S4-8 (Yoshihiro Shimoda)
* pci/controller/rcar:
misc: pci_endpoint_test: Add Device ID for R-Car S4-8 PCIe controller
MAINTAINERS: Update PCI DRIVER FOR RENESAS R-CAR for R-Car Gen4
PCI: rcar-gen4: Add endpoint mode support
PCI: rcar-gen4: Add R-Car Gen4 PCIe controller support for host mode
dt-bindings: PCI: renesas: Add R-Car Gen4 PCIe Endpoint
dt-bindings: PCI: renesas: Add R-Car Gen4 PCIe Host
dt-bindings: PCI: dwc: Update maxItems of reg and reg-names
PCI: dwc: endpoint: Introduce .pre_init() and .deinit()
PCI: dwc: Expose dw_pcie_write_dbi2() to module
PCI: dwc: Expose dw_pcie_ep_exit() to module
PCI: dwc: Add EDMA_UNROLL capability flag
PCI: dwc: endpoint: Add multiple PFs support for dbi2
PCI: tegra194: Drop PCI_EXP_LNKSTA_NLW setting
PCI: dwc: Add missing PCI_EXP_LNKCAP_MLW handling
PCI: dwc: Add dw_pcie_link_set_max_link_width()
PCI: Add T_PVPERL macro
The DWC core driver exposes the write_dbi2() callback for writing to the
DBI2 registers in a vendor-specific way.
On the Qcom EP platforms, the DBI_CS2 bit in the ELBI region needs to be
asserted before writing to any DBI2 registers and deasserted once done.
So, let's implement the callback for the Qcom PCIe EP driver so that the
DBI2 writes are correctly handled in the hardware.
Without this callback, the DBI2 register writes like BAR size won't go
through and as a result, the default BAR size is set for all BARs.
[kwilczynski: commit log, renamed function to match the DWC convention]
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231025130029.74693-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Cc: stable@vger.kernel.org # 5.16+
Add support for Xilinx XDMA Soft IP core as Root Port.
The Zynq UltraScale+ MPSoCs devices support XDMA soft IP module in
programmable logic.
The integrated XDMA Soft IP block has integrated bridge function that
can act as PCIe Root Port.
[kwilczynski: correct indentation and whitespaces, Kconfig help update]
Link: https://lore.kernel.org/linux-pci/20231003173453.938190-4-thippeswamy.havalige@amd.com
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@amd.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Move the interrupt bit definitions to the pcie-xilinx-common.h file,
which then can be shared between pcie-xilinx-cpm and the new xilinx-xdma
drivers.
While at it, also rename them so these definitions are not CPM-specific.
No functional change intended.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231003173453.938190-2-thippeswamy.havalige@amd.com
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@amd.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The PCIe Root Port controller expects ECAM size to be set through software.
As such, update the value of the NWL_ECAM_VALUE_DEFAULT macro to 16 to
allow the controller to address the 256 MB ECAM region and, as such,
enable support for detecting up to 256 buses.
[kwilczynski: commit log]
Link: https://patchwork.kernel.org/project/linux-pci/patch/20231016051102.1180432-5-thippeswamy.havalige@amd.com/
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Rename the NWL_ECAM_VALUE_DEFAULT macro to NWL_ECAM_MAX_SIZE and drop
the no longer needed ecam_value variable from struct nwl_pcie.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231016051102.1180432-4-thippeswamy.havalige@amd.com
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The PCI core already updates the primary, secondary and subordinate bus
number registers fields of the Type 1 header.
Thus, remove the redundant code from the nwl_pcie_bridge_init().
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231016051102.1180432-2-thippeswamy.havalige@amd.com
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Convert open-coded variants of PCI field access into FIELD_GET/PREP()
to make the code easier to understand.
Add two missing defines into pci_regs.h. Logically, the Max No-Snoop
Latency Register is a separate word sized register in the PCIe spec,
but the pre-existing LTR defines in pci_regs.h with dword long values
seem to consider the registers together (the same goes for the only
user). Thus, follow the custom and make the new values also take both
word long LTR registers as a joint dword register.
Link: https://lore.kernel.org/r/20231024110336.26264-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add R-Car Gen4 PCIe controller support for host mode.
This controller is based on Synopsys DesignWare PCIe. However, this
particular controller has a number of vendor-specific registers, and as
such, requires initialization code like mode setting and retraining and
so on.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-13-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Renesas R-Car Gen4 PCIe controllers require vendor-specific
initialization before .init().
To use dw->dbi and dw->num-lanes in the initialization code,
introduce .pre_init() into struct dw_pcie_ep_ops. While at it,
also introduce .deinit() to disable the controller by using
vendor-specific de-initialization.
Note that the ep_init in the struct dw_pcie_ep_ops should be
renamed to init later.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-9-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Since no PCIe controller drivers call this, this change is not required
for now. But, Renesas R-Car Gen4 PCIe controller driver will call this
and if the controller driver is built as a kernel module, the following
build error happens:
ERROR: modpost: "dw_pcie_write_dbi2" [drivers/pci/controller/dwc/pcie-rcar-gen4-host-drv.ko] undefined!
So, expose dw_pcie_write_dbi2() for it.
Link: https://lore.kernel.org/linux-pci/20230926122431.3974714-8-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Since no PCIe controller drivers call this, this change is not required
for now. But, Renesas R-Car Gen4 PCIe controller driver will call this
and if the controller driver is built as a kernel module, the following
build error happens:
ERROR: modpost: "dw_pcie_ep_exit" [drivers/pci/controller/dwc/pcie-rcar-gen4-ep-drv.ko] undefined!
So, expose dw_pcie_ep_exit() for it.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-8-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Renesas R-Car Gen4 PCIe controllers have an unexpected register value in
the eDMA CTRL register.
So, add a new capability flag "EDMA_UNROLL" which would force the unrolled
eDMA mapping for the problematic device.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-7-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
The commit 24ede430fa ("PCI: designware-ep: Add multiple PFs support
for DWC") added .func_conf_select() to get the configuration space of
different PFs and assumed that the offsets between dbi and dbi2 would
be the same.
However, Renesas R-Car Gen4 PCIe controllers have different offsets of
function 1: dbi (+0x1000) and dbi2 (+0x800). To get the offset for dbi2,
add .get_dbi2_offset() and dw_pcie_ep_get_dbi2_offset().
Note:
- .func_conf_select() should be renamed later.
- dw_pcie_ep_get_dbi2_offset() will call .func_conf_select()
if .get_dbi2_offset() doesn't exist for backward compatibility.
- dw_pcie_writeX_{dbi/dbi2} APIs accepted the func_no argument,
so that these offset calculations are contained in the API
definitions itself as it should.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-6-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
dw_pcie_setup() is already setting PCI_EXP_LNKCAP_MLW to pcie->num_lanes
in the PCI_EXP_LNKCAP register for programming maximum link width.
Hence, remove the redundant setting here.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-5-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Update dw_pcie_link_set_max_link_width() to set PCI_EXP_LNKCAP_MLW.
In accordance with the DW PCIe RC/EP HW manuals [1,2,3,...] aside with
the PORT_LINK_CTRL_OFF.LINK_CAPABLE and GEN2_CTRL_OFF.NUM_OF_LANES[8:0]
field there is another one which needs to be updated.
It's LINK_CAPABILITIES_REG.PCIE_CAP_MAX_LINK_WIDTH. If it isn't done at
the very least the maximum link-width capability CSR won't expose the
actual maximum capability.
[1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 4.60a, March 2015, p.1032
[2] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 4.70a, March 2016, p.1065
[3] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 4.90a, March 2016, p.1057
...
[X] DesignWare Cores PCI Express Controller Databook - DWC PCIe Endpoint,
Version 5.40a, March 2019, p.1396
[X+1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 5.40a, March 2019, p.1266
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
This is a preparation before adding the Max-Link-width capability
setup which would in its turn complete the max-link-width setup
procedure defined by Synopsys in the HW-manual.
Seeing there is a max-link-speed setup method defined in the DW PCIe
core driver it would be good to have a similar function for the link
width setup.
That's why we need to define a dedicated function first from already
implemented but incomplete link-width setting up code.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct hv_dr_state.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Link: https://lore.kernel.org/linux-pci/20230922175257.work.900-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Acked-by: Wei Liu <wei.liu@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: linux-hyperv@vger.kernel.org
Cc: linux-pci@vger.kernel.org
ASPM is supported by Qcom host controllers/bridges on most of the recent
platforms and so the devices tested so far. But for enabling ASPM by
default (without using Kconfig, kernel command-line or sysfs), BIOS has
to enable ASPM on both host bridge and downstream devices during boot.
Unfortunately, none of the BIOS available on Qcom platforms enables
ASPM. Due to this, the platforms making use of Qcom SoCs draw high power
during runtime.
To fix this power draw issue, users have to enable ASPM using Kconfig,
kernel command-line, sysfs or the BIOS has to start enabling ASPM.
The latter may happen in the future, but that won't address the issue on
current platforms. Also, asking users to enable a feature to get the power
management right would provide an unpleasant out-of-the-box experience.
So the apt solution is to enable ASPM in the controller driver itself. And
this is being accomplished by calling pci_enable_link_state() in the newly
introduced host_post_init() callback for all the devices connected to the
bus. This function enables all supported link low power states for both
host bridge and the downstream devices.
Due to limited testing, ASPM is only enabled for platforms making use of
ops_1_9_0 callbacks.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231010155914.9516-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
This callback can be used by the platform drivers to do configuration
once all the devices are scanned. Like changing LNKCTL of all downstream
devices to enable ASPM etc...
Link: https://lore.kernel.org/linux-pci/20231010155914.9516-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
PCIe speed returned by the PCIE_SPEED2MBS_ENC() macro is in Mbps. So
instead of converting it to MBps explicitly and using the MBps_to_icc()
macro, let's use the Mbps_to_icc() macro to pass the value directly.
Link: https://lore.kernel.org/linux-pci/20231004164430.39662-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: Vidya Sagar <vidyas@nvidia.com>
Instead of hardcoding the link speed in MBps, use existing
PCIE_SPEED2MBS_ENC() macro that does the encoding of the link speed for
us. Also, let's Wrap it with QCOM_PCIE_LINK_SPEED_TO_BW() macro to do
the conversion to ICC speed.
This eliminates the need for a switch case in qcom_pcie_icc_update() and
also works for future Gen speeds without any code modifications.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/linux-pci/20231004164430.39662-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Instead of hardcoding the link speed in MBps, use existing
PCIE_SPEED2MBS_ENC() macro that does the encoding of the link speed for
us. Also, let's Wrap it with QCOM_PCIE_LINK_SPEED_TO_BW() macro to do
the conversion to ICC speed.
This eliminates the need for a switch case in qcom_pcie_icc_update() and
also works for future Gen speeds without any code modifications.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/linux-pci/20231004164430.39662-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Instead of an "if" condition with a line split, use the usual error
handling pattern with a separate variable to improve readability.
pci_generic_config_read32() already returns either PCIBIOS_SUCCESSFUL or
PCIBIOS_DEVICE_NOT_FOUND so it is enough to simply return its return value
when ret != PCIBIOS_SUCCESSFUL.
No functional changes intended.
Link: https://lore.kernel.org/r/20230911125354.25501-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
mvebu_pcie_setup_hw() setups the Maximum Link Width field in the Link
Capabilities registers using an open-coded variant of FIELD_PREP() with
a literal in shift. Improve readability by using
FIELD_PREP(PCI_EXP_LNKCAP_MLW, ...).
Link: https://lore.kernel.org/r/20230919125648.1920-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use FIELD_GET() to extract PCIe Negotiated Link Width field instead of
custom masking and shifting.
Similarly, change custom code that misleadingly used
PCI_EXP_LNKSTA_NLW_SHIFT to prepare value for PCI_EXP_LNKCAP write
to use FIELD_PREP() with correct field define (PCI_EXP_LNKCAP_MLW).
Link: https://lore.kernel.org/r/20230919125648.1920-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The __init annotation makes the ks_pcie_probe() function disappear after
booting completes. However a device can also be bound later. In that case,
we try to call ks_pcie_probe(), but the backing memory is likely already
overwritten.
The right thing to do is do always have the probe callback available. Note
that the (wrong) __refdata annotation prevented this issue to be noticed by
modpost.
Fixes: 0c4ffcfe1f ("PCI: keystone: Add TI Keystone PCIe driver")
Link: https://lore.kernel.org/r/20231001170254.2506508-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
