Commit 6dce5aa59e ("PCI: xgene: Use inbound resources for setup")
killed PCIe on my XGene-1 box (a Mustang board). The machine itself
is still alive, but half of its storage (over NVMe) is gone, and the
NVMe driver just times out.
Note that this machine boots with a device tree provided by the
UEFI firmware (2016 vintage), which could well be non conformant
with the spec, hence the breakage.
With the patch reverted, the box boots 5.17-rc8 with flying colors.
Link: https://lore.kernel.org/all/Yf2wTLjmcRj+AbDv@xps13.dannf
Link: https://lore.kernel.org/r/20220321104843.949645-2-maz@kernel.org
Fixes: 6dce5aa59e ("PCI: xgene: Use inbound resources for setup")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Stéphane Graber <stgraber@ubuntu.com>
Cc: dann frazier <dann.frazier@canonical.com>
The CLKREQ# signal is an open drain, active low signal that is driven
low by the remote Endpoint device. But it might not be driven low if no
Endpoint device is connected.
On i.MX8MM PCIe, phy_init() may fail and system boot may hang if no
Endpoint is connected to assert CLKREQ#.
Handle this as on i.MX8MQ, where we explicitly assert CLKREQ# so the
PHY can be initialized.
Link: https://lore.kernel.org/r/1645672013-8949-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 178e244cb6 ("PCI: imx: Add the imx8mm pcie support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
To balance phy->init_count, invoke the phy_exit() after phy_power_off().
Link: https://lore.kernel.org/r/1646289275-17813-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 178e244cb6 ("PCI: imx: Add the imx8mm pcie support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
In case the controller is transitioning to L1 in rcar_pcie_config_access(),
any read/write access to PCIECDR triggers asynchronous external abort. This
is because the transition to L1 link state must be manually finished by the
driver. The PCIe IP can transition back from L1 state to L0 on its own.
The current asynchronous external abort hook implementation restarts
the instruction which finally triggered the fault, which can be a
different instruction than the read/write instruction which started
the faulting access. Usually the instruction which finally triggers
the fault is one which has some data dependency on the result of the
read/write. In case of read, the read value after fixup is undefined,
while a read value of faulting read should be PCI_ERROR_RESPONSE.
It is possible to enforce the fault using 'isb' instruction placed
right after the read/write instruction which started the faulting
access. Add custom register accessors which perform the read/write
followed immediately by 'isb'.
This way, the fault always happens on the 'isb' and in case of read,
which is located one instruction before the 'isb', it is now possible
to fix up the return value of the read in the asynchronous external
abort hook and make that read return PCI_ERROR_RESPONSE.
Link: https://lore.kernel.org/r/20220312212349.781799-2-marek.vasut@gmail.com
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
In case the controller is transitioning to L1 in rcar_pcie_config_access(),
any read/write access to PCIECDR triggers asynchronous external abort. This
is because the transition to L1 link state must be manually finished by the
driver. The PCIe IP can transition back from L1 state to L0 on its own.
Avoid triggering the abort in rcar_pcie_config_access() by checking whether
the controller is in the transition state, and if so, finish the transition
right away. This prevents a lot of unnecessary exceptions, although not all
of them.
Link: https://lore.kernel.org/r/20220312212349.781799-1-marek.vasut@gmail.com
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
- Add support for the STM32MP13 variant
- Move parent device away from struct irq_chip
- Remove all instances of non-const strings assigned to
struct irq_chip::name, enabling a nice cleanup for VIC and GIC)
- Simplify the Qualcomm PDC driver
- A bunch of SiFive PLIC cleanups
- Add support for a new variant of the Meson GPIO block
- Add support for the irqchip side of the Apple M1 PMU
- Add support for the Apple M1 Pro/Max AICv2 irqchip
- Add support for the Qualcomm MPM wakeup gadget
- Move the Xilinx driver over to the generic irqdomain handling
- Tiny speedup for IPIs on GICv3 systems
- The usual odd cleanups
-----BEGIN PGP SIGNATURE-----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=cf1B
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- Add support for the STM32MP13 variant
- Move parent device away from struct irq_chip
- Remove all instances of non-const strings assigned to
struct irq_chip::name, enabling a nice cleanup for VIC and GIC)
- Simplify the Qualcomm PDC driver
- A bunch of SiFive PLIC cleanups
- Add support for a new variant of the Meson GPIO block
- Add support for the irqchip side of the Apple M1 PMU
- Add support for the Apple M1 Pro/Max AICv2 irqchip
- Add support for the Qualcomm MPM wakeup gadget
- Move the Xilinx driver over to the generic irqdomain handling
- Tiny speedup for IPIs on GICv3 systems
- The usual odd cleanups
Link: https://lore.kernel.org/all/20220313105142.704579-1-maz@kernel.org
- New support:
- Mediatek tphy support for MT8186
- Qualcomm usb phy support for sc8180x and sc8280xp
- Qualcomm ufs phy support for sc8180x and sc8280xp
- Qualcomm usb phy support for MSM8953
- Cadence D-Phy Rx support
- Sun4i support for USB phy
- Rockchip naneng combo phy support for RK3568
- Qualcomm eDP PHY for sc7280
- Updates:
- wake on support for Synopsis XHCI controllers
- Yamilify Qualcomm USB HS phy binding
- Charger detection support for TI tusb1210
-----BEGIN PGP SIGNATURE-----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=8baK
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-next
Vinod writes:
phy-for-5.18
- New support:
- Mediatek tphy support for MT8186
- Qualcomm usb phy support for sc8180x and sc8280xp
- Qualcomm ufs phy support for sc8180x and sc8280xp
- Qualcomm usb phy support for MSM8953
- Cadence D-Phy Rx support
- Sun4i support for USB phy
- Rockchip naneng combo phy support for RK3568
- Qualcomm eDP PHY for sc7280
- Updates:
- wake on support for Synopsis XHCI controllers
- Yamilify Qualcomm USB HS phy binding
- Charger detection support for TI tusb1210
* tag 'phy-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (53 commits)
phy: qcom-qmp: add sc8280xp UFS PHY
dt-bindings: phy: qcom,qmp: add sc8180x and sc8280xp ufs compatibles
phy: qcom-snps: Add sc8280xp support
dt-bindings: phy: qcom,usb-snps-femto-v2: Add sc8180x and sc8280xp
dt-bindings: Revert "dt-bindings: soc: grf: add naneng combo phy register compatible"
phy: dt-bindings: Add Cadence D-PHY Rx bindings
phy: dt-bindings: cdns,dphy: add power-domains property
phy: dt-bindings: Convert Cadence DPHY binding to YAML
phy: cadence: Add Cadence D-PHY Rx driver
dt-bindings: phy: renesas,usb2-phy: Document RZ/V2L phy bindings
Revert "PCI: aardvark: Fix initialization with old Marvell's Arm Trusted Firmware"
Revert "usb: host: xhci: mvebu: make USB 3.0 PHY optional for Armada 3720"
Revert "ata: ahci: mvebu: Make SATA PHY optional for Armada 3720"
phy: marvell: phy-mvebu-a3700-comphy: Add native kernel implementation
phy: marvell: phy-mvebu-a3700-comphy: Remove port from driver configuration
phy: phy-brcm-usb: fixup BCM4908 support
dt-bindings: phy: mediatek,tphy: Add compatible for MT8192
phy: ti: tusb1210: Add charger detection
phy: ti: tusb1210: Add a delay between power-on and restoring the phy-parameters
phy: ti: tusb1210: Drop tusb->vendor_specific2 != 0 check from tusb1210_power_on()
...
If a host that uses the IP's integrated MSI Receiver lost power
during suspend, we call dw_pcie_setup_rc() to reinit the RC. But
dw_pcie_setup_rc() always sets pp->irq_mask[ctrl] to ~0, so the mask
register is always set as 0xffffffff incorrectly, thus the MSI can't
work after resume.
Fix this issue by moving pp->irq_mask[ctrl] initialization to
dw_pcie_host_init() so we can correctly set the mask reg during both
boot and resume.
Tested-by: Richard Zhu <hongxing.zhu@nxp.com>
Link: https://lore.kernel.org/r/20211226074019.2556-1-jszhang@kernel.org
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The calls to devm_gpiod_get_optional() have the -gpios at the end of the
name but the GPIO core code is already adding the suffix during the lookup.
This means the PCIe driver is not finding the necessary reset or power
lines to allow initialisation of the PCIe.
Drop the redundant '-gpios' when we look up GPIOs from the DT.
This bug has not been noticed because if U-Boot has setup the GPIO lines
for the hardware when it does the PCIe initialisation (either by booting
from PCIe or user command to access PCIe) then the PCIe will work in Linux.
The U-Boot as supplied by SiFive does not by default initialise any PCIe
component.
Link: https://lore.kernel.org/r/20220221210347.1335004-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
AIC2 changes the IRQ fwspec to add a cell. Always use the second-to-last
cell for the MSI handling, so it will work for both AIC1 and AIC2 devices.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220309192123.152028-2-marcan@marcan.st
i.MX6QP PCIe supports the reset logic, thus it can reset itself to the
initialized state when exit from L2 or L3 states.
Enable the i.MX6QP PCIe suspend/resume operations support.
Link: https://lore.kernel.org/r/1645425237-4071-2-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
On ARM64 Hyper-V guests, SPIs are used for the interrupts of virtual PCI
devices, and SPIs can be managed directly via GICD registers. Therefore
the retarget interrupt hypercall is not needed on ARM64.
An arch-specific interface hv_arch_irq_unmask() is introduced to handle
the architecture level differences on this. For x86, the behavior
remains unchanged, while for ARM64 no hypercall is invoked when
unmasking an irq for virtual PCI devices.
Link: https://lore.kernel.org/r/20220217034525.1687678-1-boqun.feng@gmail.com
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
resulted in a recursive locking problem in the VMD driver. The cure is to
cache the relevant information upfront instead of retrieving it at runtime.
-----BEGIN PGP SIGNATURE-----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=ukul
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2022-02-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single fix for a regression caused by the recent PCI/MSI rework
which resulted in a recursive locking problem in the VMD driver.
The cure is to cache the relevant information upfront instead of
retrieving it at runtime"
* tag 'irq-urgent-2022-02-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
PCI: vmd: Prevent recursive locking on interrupt allocation
This reverts commit b0c6ae0f89.
Armada 3720 phy driver (phy-mvebu-a3700-comphy.c) does not return
-EOPNOTSUPP from phy_power_on() callback anymore.
So remove dead code which handles -EOPNOTSUPP return value.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20220203214444.1508-6-kabel@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
-----BEGIN PGP SIGNATURE-----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=8/1S
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.17-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci fixes from Bjorn Helgaas:
- Fix a merge error that broke PCI device enumeration on mvebu
platforms, including Turris Omnia (Armada 385) (Pali Rohár)
- Avoid using ATS on all AMD Navi10 and Navi14 GPUs because some
VBIOSes don't account for "harvested" (disabled) parts of the chip
when initializing caches (Alex Deucher)
* tag 'pci-v5.17-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Mark all AMD Navi10 and Navi14 GPU ATS as broken
PCI: mvebu: Fix device enumeration regression
On SM8450 platform PCIe hosts do not use all the clocks (and add several
additional clocks), so expand the driver to handle these requirements.
PCIe0 and PCIe1 hosts use different sets of clocks, so separate entries
are required.
Link: https://lore.kernel.org/r/20220223101435.447839-5-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Qualcomm PCIe driver uses compatible string to check if the ddrss_sf_tbu
clock should be used. Since sc7280 support has added flags, switch to
the new mechanism to check if this clock should be used.
Link: https://lore.kernel.org/r/20220223101435.447839-4-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
In preparation to adding more flags to configuration data, use pointer
to struct qcom_pcie_cfg directly inside struct qcom_pcie, rather than
duplicating all its fields. This would save us from the boilerplate code
that just copies flag values from one struct to another one.
Link: https://lore.kernel.org/r/20220223101435.447839-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
This adds support for legacy INTx interrupts received from other PCIe
devices and which are reported by a new INTx irq chip.
With this change, kernel can distinguish between INTA, INTB, INTC and INTD
interrupts.
Note that for this support, device tree files has to be properly adjusted
to provide "interrupts" or "interrupts-extended" property with intx
interrupt source, "interrupt-names" property with "intx" string and also
'interrupt-controller' subnode must be defined.
If device tree files do not provide these nodes then driver would work as
before.
Link: https://lore.kernel.org/r/20220222155030.988-12-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Register 0x1910 unmasks interrupts and legacy INTx interrupts are unmasked
because driver does not support individual masking yet.
Link: https://lore.kernel.org/r/20220222155030.988-11-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Split struct pci_ops between ops and child_ops. Member ops is used for
accessing PCIe Root Ports via pci-bridge-emul.c driver and child_ops for
accessing real PCIe cards.
There is no need to mix these two struct pci_ops into one as PCI core code
already provides separate callbacks via bridge->ops and bridge->child_ops.
Link: https://lore.kernel.org/r/20220222155030.988-9-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
AER registers start at mvebu offset 0x0100. Registers PCI_ERR_ROOT_COMMAND,
PCI_ERR_ROOT_STATUS and PCI_ERR_ROOT_ERR_SRC are not supported on pre-XP
hardware and returns zeros.
Note that AER interrupt is not supported yet as mvebu emulated bridge does
not implement interrupts support at all yet.
Also remove custom macro PCIE_HEADER_LOG_4_OFF as it is unused and
correctly this register should be referenced via standard macros with
offset, e.g. as: PCIE_CAP_PCIERR_OFF + PCI_ERR_HEADER_LOG + 4.
Link: https://lore.kernel.org/r/20220222155030.988-8-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Register with Subsystem Device/Vendor ID is at offset 0x2c. Export is via
emulated bridge.
After this change Subsystem ID is visible in lspci output at line:
Capabilities: [40] Subsystem
Link: https://lore.kernel.org/r/20220222155030.988-7-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
If x1/x4 mode is not set correctly then link with endpoint card is not
established.
Use DTS property 'num-lanes' to deteriminate x1/x4 mode.
Link: https://lore.kernel.org/r/20220222155030.988-6-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tejas reported the following recursive locking issue:
swapper/0/1 is trying to acquire lock:
ffff8881074fd0a0 (&md->mutex){+.+.}-{3:3}, at: msi_get_virq+0x30/0xc0
but task is already holding lock:
ffff8881017cd6a0 (&md->mutex){+.+.}-{3:3}, at: __pci_enable_msi_range+0xf2/0x290
stack backtrace:
__mutex_lock+0x9d/0x920
msi_get_virq+0x30/0xc0
pci_irq_vector+0x26/0x30
vmd_msi_init+0xcc/0x210
msi_domain_alloc+0xbf/0x150
msi_domain_alloc_irqs_descs_locked+0x3e/0xb0
__pci_enable_msi_range+0x155/0x290
pci_alloc_irq_vectors_affinity+0xba/0x100
pcie_port_device_register+0x307/0x550
pcie_portdrv_probe+0x3c/0xd0
pci_device_probe+0x95/0x110
This is caused by the VMD MSI code which does a lookup of the Linux
interrupt number for an VMD managed MSI[X] vector. The lookup function
tries to acquire the already held mutex.
Avoid that by caching the Linux interrupt number at initialization time
instead of looking it up over and over.
Fixes: 82ff8e6b78 ("PCI/MSI: Use msi_get_virq() in pci_get_vector()")
Reported-by: "Surendrakumar Upadhyay, TejaskumarX" <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: "Surendrakumar Upadhyay, TejaskumarX" <tejaskumarx.surendrakumar.upadhyay@intel.com>
Cc: linux-pci@vger.kernel.org
Link: https://lore.kernel.org/r/87a6euub2a.ffs@tglx
Register 0x43c in its low 24 bits contains PCI class code.
Update code to set all 24 bits of PCI class code and not only upper 16 bits
of PCI class code.
Use a new macro PCI_CLASS_BRIDGE_PCI_NORMAL which represents whole 24 bits
of normal PCI bridge class.
Link: https://lore.kernel.org/r/20220214114109.26809-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Roman Bacik <roman.bacik@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Add these PCI class codes to pci_ids.h:
PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE
Use these defines in all kernel code for describing PCI class codes for
normal and subtractive PCI bridges.
[bhelgaas: similar change in pci-mvebu.c]
Link: https://lore.kernel.org/r/20220214114109.26809-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAmILjZgTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXuPAB/96ls6ZaUrvAEseODu9N+qbCKCjqjGx
LBqP5gzzG71LoFLlvvGp7quwDXkSlfzMmZM1oxBrsRN4TiexdQ4b9tR2jNqxUBS0
pR7efRpR4YN1TrvxCr0lgfbKV6F3EC4YqMwK2Tf7zMRkzAbMQmw500JTkAdtplUT
opSZKlWt1Q66Iudz7vwz2e2D/NnAg03icB7lZUNulV1WTDfDfBUZyAphAnOqpty9
Y9UlVjFYSozOA6dv3HClYiJPjxhzUev88W/Sld81+2+gGCngWRT4a2OyUvCqNWXD
P8EswLHuqECpkz6uxnbQOLDBgdiMXigtANNky/E4Za8r9MqpZT3+ueLf
=/jBG
-----END PGP SIGNATURE-----
Merge tag 'hyperv-fixes-signed-20220215' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- Rework use of DMA_BIT_MASK in vmbus to work around a clang bug
(Michael Kelley)
- Fix NUMA topology (Long Li)
- Fix a memory leak in vmbus (Miaoqian Lin)
- One minor clean-up patch (Cai Huoqing)
* tag 'hyperv-fixes-signed-20220215' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
Drivers: hv: utils: Make use of the helper macro LIST_HEAD()
Drivers: hv: vmbus: Rework use of DMA_BIT_MASK(64)
Drivers: hv: vmbus: Fix memory leak in vmbus_add_channel_kobj
PCI: hv: Fix NUMA node assignment when kernel boots with custom NUMA topology
Add basic support for UniPhier NX1 SoC as non-legacy SoC. This includes
a compatible string, SoC-dependent data containing init() and wait()
functions for the controller.
Link: https://lore.kernel.org/r/1644480596-20037-4-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Define SoC data structure that includes pci_epc_features, SoC-dependent
callback functions and flags to distinguish the behavior of each SoC.
The callback functions define init() to initialize the controller and
wait() to wait until initialization is completed.
Rename uniphier_pcie_init_ep() to uniphier_pcie_pro5_init_ep() for
initializing PCIe controller implemented in Pro5 SoC. And Pro5 SoC
doesn't have wait() function.
Link: https://lore.kernel.org/r/1644480596-20037-3-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Update the comment about what happens when link goes down after we have
checked for link-up. If a PIO request is done while link-down, we have
a serious problem.
Link: https://lore.kernel.org/r/20220110015018.26359-23-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This function is now always used in driver remove method, drop the
__maybe_unused attribute.
Link: https://lore.kernel.org/r/20220110015018.26359-22-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
By default, all Legacy INTx interrupts are masked, so there is no need to
mask this interrupt during irq_map() callback.
Link: https://lore.kernel.org/r/20220110015018.26359-21-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Callback for irq_mask_ack() is the same as for irq_mask(). As there is no
special handling for irq_ack(), there is no need to define irq_mask_ack()
too.
Link: https://lore.kernel.org/r/20220110015018.26359-20-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Emulated root bridge currently provides only one Legacy INTA interrupt
which is used for reporting PCIe PME and ERR events and handled by kernel
PCIe PME and AER drivers.
Aardvark HW reports these PME and ERR events separately, so there is no
need to mix real INTA interrupt and emulated INTA interrupt for PCIe PME
and AER drivers.
Register a new advk-RP (as in Root Port) irq chip and a new irq domain
for emulated root bridge and use this new separate irq domain for
providing INTA interrupt from emulated root bridge for PME and ERR events.
The real INTA interrupt from real devices is now separate.
A custom map_irq callback function on PCI host bridge structure is used to
allocate IRQ mapping for emulated root bridge from new irq domain. Original
callback of_irq_parse_and_map_pci() is used for all other devices as before.
Link: https://lore.kernel.org/r/20220110015018.26359-19-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Enable aardvark PME interrupt unconditionally by unmasking it and read PME
requester ID to emulated bridge config space immediately after receiving
interrupt.
PME requester ID is stored in the PCIE_MSG_LOG_REG register, which contains
the last inbound message. So when new inbound message is received by HW
(including non-PM), the content in PCIE_MSG_LOG_REG register is replaced by
a new value.
PCIe specification mandates that subsequent PMEs are kept pending until the
PME Status Register bit is cleared by software by writing a 1b.
Support for masking/unmasking PME interrupt on emulated bridge via
PCI_EXP_RTCTL_PMEIE bit is now implemented only in emulated bridge config
space, to ensure that we do not miss any aardvark PME interrupt.
Reading of PCI_EXP_RTCAP and PCI_EXP_RTSTA registers is simplified as final
value is now always stored into emulated bridge config space by the
interrupt handler, so there is no need to implement support for these
registers in read_pcie callback.
Clearing of W1C bit PCI_EXP_RTSTA_PME is now also simplified as it is done
by pci-bridge-emul.c code for emulated bridge config space. So there is no
need to implement support for clearing this bit in write_pcie callback.
Link: https://lore.kernel.org/r/20220110015018.26359-18-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Currently enabling PCI_EXP_RTSTA_PME bit in PCI_EXP_RTCTL register does
nothing. This is because PCIe PME driver expects to receive PCIe interrupt
defined in PCI_EXP_FLAGS_IRQ register, but aardvark hardware does not
trigger PCIe INTx/MSI interrupt for PME event, rather it triggers custom
aardvark interrupt which this driver is not processing yet.
Fix this issue by handling PME interrupt in advk_pcie_handle_int() and
chaining it to PCIe interrupt 0 with generic_handle_domain_irq() (since
aardvark sets PCI_EXP_FLAGS_IRQ to zero). With this change PCIe PME driver
finally starts receiving PME interrupt.
Link: https://lore.kernel.org/r/20220110015018.26359-17-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
To optimize advk_pci_bridge_emul_pcie_conf_write() code, touch
PCIE_ISR0_REG and PCIE_ISR0_MASK_REG registers only when it is really
needed, when processing PCI_EXP_RTCTL_PMEIE and PCI_EXP_RTSTA_PME bits.
Link: https://lore.kernel.org/r/20220110015018.26359-16-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The emulated bridge returns incorrect value for PCI_EXP_RTSTA register
during readout in advk_pci_bridge_emul_pcie_conf_read() function: the
correct bit is BIT(16), but we are setting BIT(23), because the code
does
*value = (isr0 & PCIE_MSG_PM_PME_MASK) << 16
where
PCIE_MSG_PM_PME_MASK
is
BIT(7).
The code should probably have been something like
*value = (!!(isr0 & PCIE_MSG_PM_PME_MASK)) << 16,
but we are better of using an if() and using the proper macro for this
bit.
Link: https://lore.kernel.org/r/20220110015018.26359-15-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
ERR interrupt is triggered when corresponding bit is unmasked in both ISR0
and PCI_EXP_DEVCTL registers. Unmasking ERR bits in PCI_EXP_DEVCTL register
is not enough. This means that currently the ERR interrupt is never
triggered.
Unmask ERR bits in ISR0 register at driver probe time. ERR interrupt is not
triggered until ERR bits are unmasked also in PCI_EXP_DEVCTL register,
which is done by AER driver. So it is safe to unconditionally unmask all
ERR bits in aardvark probe.
Aardvark HW sets PCI_ERR_ROOT_AER_IRQ to zero and when corresponding bits
in ISR0 and PCI_EXP_DEVCTL are enabled, the HW triggers a generic interrupt
on GIC. Chain this interrupt to PCIe interrupt 0 with
generic_handle_domain_irq() to allow processing of ERR interrupts.
Link: https://lore.kernel.org/r/20220110015018.26359-14-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
According to PCI 3.0 specification, sending both MSI and MSI-X interrupts
is done by DWORD memory write operation to doorbell message address. The
write operation for MSI has zero upper 16 bits and the MSI interrupt number
in the lower 16 bits, while the write operation for MSI-X contains a 32-bit
value from MSI-X table.
Since the driver only uses interrupt numbers from range 0..31, the upper
16 bits of the DWORD memory write operation to doorbell message address
are zero even for MSI-X interrupts. Thus we can enable MSI-X interrupts.
Testing proves that kernel can correctly receive MSI-X interrupts from PCIe
cards which supports both MSI and MSI-X interrupts.
Link: https://lore.kernel.org/r/20220110015018.26359-13-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
MSI address for receiving MSI interrupts needs to be correctly set before
enabling processing of MSI interrupts.
Move code for setting PCIE_MSI_ADDR_LOW_REG and PCIE_MSI_ADDR_HIGH_REG
from advk_pcie_init_msi_irq_domain() to advk_pcie_setup_hw(), before
enabling PCIE_CORE_CTRL2_MSI_ENABLE.
After this we can remove the now unused member msi_msg, which was used
only for MSI doorbell address. MSI address can be any address which cannot
be used to DMA to. So change it to the address of the main struct advk_pcie.
Link: https://lore.kernel.org/r/20220110015018.26359-12-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # f21a8b1b68 ("PCI: aardvark: Move to MSI handling using generic MSI support")
We should not unmask MSIs at setup, but only when kernel asks for them
to be unmasked.
At setup, mask all MSIs, and implement IRQ chip callbacks for masking
and unmasking particular MSIs.
Link: https://lore.kernel.org/r/20220110015018.26359-11-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Refactor the masking of ISR0/1 Sources and unmasking of summary MSI interrupt
so that it corresponds to the comments:
- first mask all ISR0/1
- then unmask all MSIs
- then unmask summary MSI interrupt
Link: https://lore.kernel.org/r/20220110015018.26359-10-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Use simple
dev_fwnode(dev)
instead of
struct device_node *node = dev->of_node;
of_node_to_fwnode(node)
especially since the node variable is not used elsewhere in the function.
Link: https://lore.kernel.org/r/20220110015018.26359-9-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Make Aardvark's msi_domain_info structure into a private driver structure.
Domain info is same for every potential instatination of a controller.
Link: https://lore.kernel.org/r/20220110015018.26359-8-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
It is possible that we receive spurious INTx interrupt. Check for the
return value of generic_handle_domain_irq() when processing INTx IRQ.
Link: https://lore.kernel.org/r/20220110015018.26359-6-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Rewrite the code to use irq_set_chained_handler_and_data() handler with
chained_irq_enter() and chained_irq_exit() processing instead of using
devm_request_irq().
advk_pcie_irq_handler() reads IRQ status bits and calls other functions
based on which bits are set. These functions then read its own IRQ status
bits and calls other aardvark functions based on these bits. Finally
generic_handle_domain_irq() with translated linux IRQ numbers are called.
Link: https://lore.kernel.org/r/20220110015018.26359-5-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Aardvark hardware supports Multi-MSI and MSI_FLAG_MULTI_PCI_MSI is already
set for the MSI chip. But when allocating MSI interrupt numbers for
Multi-MSI, the numbers need to be properly aligned, otherwise endpoint
devices send MSI interrupt with incorrect numbers.
Fix this issue by using function bitmap_find_free_region() instead of
bitmap_find_next_zero_area().
To ensure that aligned MSI interrupt numbers are used by endpoint devices,
we cannot use Linux virtual irq numbers (as they are random and not
properly aligned). Instead we need to use the aligned hwirq numbers.
This change fixes receiving MSI interrupts on Armada 3720 boards and
allows using NVMe disks which use Multi-MSI feature with 3 interrupts.
Without this NVMe disks freeze booting as linux nvme-core.c is waiting
60s for an interrupt.
Link: https://lore.kernel.org/r/20220110015018.26359-4-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
In advk_pcie_handle_msi() it is expected that when bit i in the W1C
register PCIE_MSI_STATUS_REG is cleared, the PCIE_MSI_PAYLOAD_REG is
updated to contain the MSI number corresponding to index i.
Experiments show that this is not so, and instead PCIE_MSI_PAYLOAD_REG
always contains the number of the last received MSI, overall.
Do not read PCIE_MSI_PAYLOAD_REG register for determining MSI interrupt
number. Since Aardvark already forbids more than 32 interrupts and uses
own allocated hwirq numbers, the msi_idx already corresponds to the
received MSI number.
Link: https://lore.kernel.org/r/20220110015018.26359-3-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
-----BEGIN PGP SIGNATURE-----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=4e8j
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.17-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci fixes from Bjorn Helgaas:
- Restructure j721e_pcie_probe() so we don't dereference a NULL pointer
(Bjorn Helgaas)
- Add a kirin_pcie_data struct to identify different Kirin variants to
fix probe failure for controllers with an internal PHY (Bjorn
Helgaas)
* tag 'pci-v5.17-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: kirin: Add dev struct for of_device_get_match_data()
PCI: j721e: Initialize pcie->cdns_pcie before using it
Bean reported that a622435fbe ("PCI: kirin: Prefer
of_device_get_match_data()") broke kirin_pcie_probe() because it assumed
match data of 0 was a failure when in fact, it meant the match data was
"(void *)PCIE_KIRIN_INTERNAL_PHY".
Therefore, probing of "hisilicon,kirin960-pcie" devices failed with -EINVAL
and an "OF data missing" message.
Add a struct kirin_pcie_data to encode the PHY type. Then the result of
of_device_get_match_data() should always be a non-NULL pointer to a struct
kirin_pcie_data that contains the PHY type.
Fixes: a622435fbe ("PCI: kirin: Prefer of_device_get_match_data()")
Link: https://lore.kernel.org/r/20220202162659.GA12603@bhelgaas
Link: https://lore.kernel.org/r/20220201215941.1203155-1-huobean@gmail.com
Reported-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The intention of commit 886a9c1347 ("PCI: dwc: Move link handling into
common code") was to standardize the behavior of link down as explained
in its commit log:
"The behavior for a link down was inconsistent as some drivers would fail
probe in that case while others succeed. Let's standardize this to
succeed as there are usecases where devices (and the link) appear later
even without hotplug. For example, a reconfigured FPGA device."
The pci-imx6 still fails to probe when the link is not present, which
causes the following warning:
imx6q-pcie 8ffc000.pcie: Phy link never came up
imx6q-pcie: probe of 8ffc000.pcie failed with error -110
------------[ cut here ]------------
WARNING: CPU: 0 PID: 30 at drivers/regulator/core.c:2257 _regulator_put.part.0+0x1b8/0x1dc
Modules linked in:
CPU: 0 PID: 30 Comm: kworker/u2:2 Not tainted 5.15.0-next-20211103 #1
Hardware name: Freescale i.MX6 SoloX (Device Tree)
Workqueue: events_unbound async_run_entry_fn
[<c0111730>] (unwind_backtrace) from [<c010bb74>] (show_stack+0x10/0x14)
[<c010bb74>] (show_stack) from [<c0f90290>] (dump_stack_lvl+0x58/0x70)
[<c0f90290>] (dump_stack_lvl) from [<c012631c>] (__warn+0xd4/0x154)
[<c012631c>] (__warn) from [<c0f87b00>] (warn_slowpath_fmt+0x74/0xa8)
[<c0f87b00>] (warn_slowpath_fmt) from [<c076b4bc>] (_regulator_put.part.0+0x1b8/0x1dc)
[<c076b4bc>] (_regulator_put.part.0) from [<c076b574>] (regulator_put+0x2c/0x3c)
[<c076b574>] (regulator_put) from [<c08c3740>] (release_nodes+0x50/0x178)
Fix this problem by ignoring the dw_pcie_wait_for_link() error like
it is done on the other dwc drivers.
Tested on imx6sx-sdb and imx6q-sabresd boards.
Link: https://lore.kernel.org/r/20220106103645.2790803-1-festevam@gmail.com
Fixes: 886a9c1347 ("PCI: dwc: Move link handling into common code")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: <stable@vger.kernel.org>
When kernel boots with a NUMA topology with some NUMA nodes offline, the PCI
driver should only set an online NUMA node on the device. This can happen
during KDUMP where some NUMA nodes are not made online by the KDUMP kernel.
This patch also fixes the case where kernel is booting with "numa=off".
Fixes: 999dd956d8 ("PCI: hv: Add support for protocol 1.3 and support PCI_BUS_RELATIONS2")
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Purna Pavan Chandra Aekkaladevi <paekkaladevi@microsoft.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/1643247814-15184-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Add support for reporting PCI_EXP_LNKSTA_DLLLA bit in Link Control register
on emulated bridge via PCIE_STAT_OFF reg. Function mvebu_pcie_link_up()
already parses this register and returns if Data Link is Active or not.
Also correctly indicate DLLLA capability via PCI_EXP_LNKCAP_DLLLARC bit in
Link Control Capability register which is required for reporting DLLLA bit.
Link: https://lore.kernel.org/r/20220104153529.31647-12-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Logic and code for clearing PCI_EXP_LNKCTL_CLKREQ_EN bit is correct, but
comment describing it is misleading. PCI_EXP_LNKCTL_CLKREQ_EN bit should be
hardwired to zero but mvebu hw allows to change it.
Link: https://lore.kernel.org/r/20220104153529.31647-11-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reason for clearing this bit is because mvebu hw returns incorrectly this bit set to 1.
Link: https://lore.kernel.org/r/20220104153529.31647-10-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
With this change also PCI vendor id is read from mvebu registers.
Link: https://lore.kernel.org/r/20220104153529.31647-9-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This will make PCI bridge to return zeros when accessing IO base and limit
registers, as required by PCIe base specification.
This allows to remove adhoc checks around mvebu_pcie_handle_iobase_change()
function for unsupported IO ranges. PCI_BRIDGE_EMUL_NO_IO_FORWARD ensures
that there will be no non-zeros write to IO registers when IO is not
supported.
Link: https://lore.kernel.org/r/20220104153529.31647-8-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Member pcie->nports is initialized to correct value before the previous
for-loop. There is not need to initialize it more times.
Link: https://lore.kernel.org/r/20220104153529.31647-7-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
There is no description for CONFIG_PCI_MVEBU option. Add it.
Link: https://lore.kernel.org/r/20220104153529.31647-6-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This flag describe whether PCI bridge supports forwarding of prefetchable
memory requests in given range between primary and secondary buses. It does
not specify if bridge has support for prefetchable memory BAR (moreover
this pci-bridge-emul.c driver does not provide support for BARs).
So change name of this flag to be less misleading and add comment.
Link: https://lore.kernel.org/r/20220104153529.31647-4-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
It is read-only constant structure, so properly mark it with const keyword.
Link: https://lore.kernel.org/r/20220104153529.31647-3-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Christian reported a NULL pointer dereference in j721e_pcie_probe() caused
by 19e863828a ("PCI: j721e: Drop redundant struct device *"), which
removed struct j721e_pcie.dev since there's another copy in struct
cdns_pcie.dev reachable via j721e_pcie->cdns_pcie->dev.
The problem is that j721e_pcie->cdns_pcie was dereferenced before being
initialized:
j721e_pcie_probe
pcie = devm_kzalloc() # struct j721e_pcie
j721e_pcie_ctrl_init(pcie)
dev = pcie->cdns_pcie->dev <-- dereference cdns_pcie
switch (mode) {
case PCI_MODE_RC:
cdns_pcie = ... # alloc as part of pci_host_bridge
pcie->cdns_pcie = cdns_pcie <-- initialize pcie->cdns_pcie
Move the cdns_pcie initialization earlier so it is done before it is used.
This also simplifies the error exits.
Fixes: 19e863828a ("PCI: j721e: Drop redundant struct device *")
Link: https://lore.kernel.org/r/20220127222951.GA144828@bhelgaas
Link: https://lore.kernel.org/r/20220124122132.435743-1-christian.gmeiner@gmail.com
Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Tested-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Function pcie_rmw() is not being used at all and can be deleted. Hence get
rid of it, which fixes this warning:
drivers/pci/controller/pcie-mt7621.c:112:20: warning: unused function 'pcie_rmw' [-Wunused-function]
Fixes: 2bdd5238e7 ("PCI: mt7621: Add MediaTek MT7621 PCIe host controller driver")
Link: https://lore.kernel.org/r/20220124113003.406224-3-sergio.paracuellos@gmail.com
Link: https://lore.kernel.org/all/202201241754.igtHzgHv-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We have stubs for most OF interfaces even when CONFIG_OF is not set, so we
allow building of pcie-mt7621.c in that case for compile testing.
When CONFIG_OF is not set, "of_match_ptr(mt7621_pcie_ids)" compiles to
NULL, which leaves mt7621_pcie_ids unused:
$ make W=1
drivers/pci/controller/pcie-mt7621.c:549:34: warning: unused variable 'mt7621_pcie_ids' [-Wunused-const-variable]
Drop of_match_ptr() to avoid the unused variable warning.
[bhelgaas: commit log]
Fixes: 2bdd5238e7 ("PCI: mt7621: Add MediaTek MT7621 PCIe host controller driver")
Link: https://lore.kernel.org/r/20220124113003.406224-2-sergio.paracuellos@gmail.com
Link: https://lore.kernel.org/r/202201241754.igtHzgHv-lkp@intel.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----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=RKW4
-----END PGP SIGNATURE-----
Merge tag 'bitmap-5.17-rc1' of git://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- introduce for_each_set_bitrange()
- use find_first_*_bit() instead of find_next_*_bit() where possible
- unify for_each_bit() macros
* tag 'bitmap-5.17-rc1' of git://github.com/norov/linux:
vsprintf: rework bitmap_list_string
lib: bitmap: add performance test for bitmap_print_to_pagebuf
bitmap: unify find_bit operations
mm/percpu: micro-optimize pcpu_is_populated()
Replace for_each_*_bit_from() with for_each_*_bit() where appropriate
find: micro-optimize for_each_{set,clear}_bit()
include/linux: move for_each_bit() macros from bitops.h to find.h
cpumask: replace cpumask_next_* with cpumask_first_* where appropriate
tools: sync tools/bitmap with mother linux
all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate
cpumask: use find_first_and_bit()
lib: add find_first_and_bit()
arch: remove GENERIC_FIND_FIRST_BIT entirely
include: move find.h from asm_generic to linux
bitops: move find_bit_*_le functions from le.h to find.h
bitops: protect find_first_{,zero}_bit properly
-----BEGIN PGP SIGNATURE-----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=Vgg4
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Use pci_find_vsec_capability() instead of open-coding it (Andy
Shevchenko)
- Convert pci_dev_present() stub from macro to static inline to avoid
'unused variable' errors (Hans de Goede)
- Convert sysfs slot attributes from default_attrs to default_groups
(Greg Kroah-Hartman)
- Use DWORD accesses for LTR, L1 SS to avoid BayHub OZ711LV2 erratum
(Rajat Jain)
- Remove unnecessary initialization of static variables (Longji Guo)
Resource management:
- Always write Intel I210 ROM BAR on update to work around device
defect (Bjorn Helgaas)
PCIe native device hotplug:
- Fix pciehp lockdep errors on Thunderbolt undock (Hans de Goede)
- Fix infinite loop in pciehp IRQ handler on power fault (Lukas
Wunner)
Power management:
- Convert amd64-agp, sis-agp, via-agp from legacy PCI power
management to generic power management (Vaibhav Gupta)
IOMMU:
- Add function 1 DMA alias quirk for Marvell 88SE9125 SATA controller
so it can work with an IOMMU (Yifeng Li)
Error handling:
- Add PCI_ERROR_RESPONSE and related definitions for signaling and
checking for transaction errors on PCI (Naveen Naidu)
- Fabricate PCI_ERROR_RESPONSE data (~0) in config read wrappers,
instead of in host controller drivers, when transactions fail on
PCI (Naveen Naidu)
- Use PCI_POSSIBLE_ERROR() to check for possible failure of config
reads (Naveen Naidu)
Peer-to-peer DMA:
- Add Logan Gunthorpe as P2PDMA maintainer (Bjorn Helgaas)
ASPM:
- Calculate link L0s and L1 exit latencies when needed instead of
caching them (Saheed O. Bolarinwa)
- Calculate device L0s and L1 acceptable exit latencies when needed
instead of caching them (Saheed O. Bolarinwa)
- Remove struct aspm_latency since it's no longer needed (Saheed O.
Bolarinwa)
APM X-Gene PCIe controller driver:
- Fix IB window setup, which was broken by the fact that IB resources
are now sorted in address order instead of DT dma-ranges order (Rob
Herring)
Apple PCIe controller driver:
- Enable clock gating to save power (Hector Martin)
- Fix REFCLK1 enable/poll logic (Hector Martin)
Broadcom STB PCIe controller driver:
- Declare bitmap correctly for use by bitmap interfaces (Christophe
JAILLET)
- Clean up computation of legacy and non-legacy MSI bitmasks (Florian
Fainelli)
- Update suspend/resume/remove error handling to warn about errors
and not fail the operation (Jim Quinlan)
- Correct the "pcie" and "msi" interrupt descriptions in DT binding
(Jim Quinlan)
- Add DT bindings for endpoint voltage regulators (Jim Quinlan)
- Split brcm_pcie_setup() into two functions (Jim Quinlan)
- Add mechanism for turning on voltage regulators for connected
devices (Jim Quinlan)
- Turn voltage regulators for connected devices on/off when bus is
added or removed (Jim Quinlan)
- When suspending, don't turn off voltage regulators for wakeup
devices (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Use DWC common ops instead of layerscape-specific link-up functions
(Hou Zhiqiang)
Intel VMD host bridge driver:
- Honor platform ACPI _OSC feature negotiation for Root Ports below
VMD (Kai-Heng Feng)
- Add support for Raptor Lake SKUs (Karthik L Gopalakrishnan)
- Reset everything below VMD before enumerating to work around
failure to enumerate NVMe devices when guest OS reboots (Nirmal
Patel)
Bridge emulation (used by Marvell Aardvark and MVEBU):
- Make emulated ROM BAR read-only by default (Pali Rohár)
- Make some emulated legacy PCI bits read-only for PCIe devices (Pali
Rohár)
- Update reserved bits in emulated PCIe Capability (Pali Rohár)
- Allow drivers to emulate different PCIe Capability versions (Pali
Rohár)
- Set emulated Capabilities List bit for all PCIe devices, since they
must have at least a PCIe Capability (Pali Rohár)
Marvell Aardvark PCIe controller driver:
- Add bridge emulation definitions for PCIe DEVCAP2, DEVCTL2,
DEVSTA2, LNKCAP2, LNKCTL2, LNKSTA2, SLTCAP2, SLTCTL2, SLTSTA2 (Pali
Rohár)
- Add aardvark support for DEVCAP2, DEVCTL2, LNKCAP2 and LNKCTL2
registers (Pali Rohár)
- Clear all MSIs at setup to avoid spurious interrupts (Pali Rohár)
- Disable bus mastering when unbinding host controller driver (Pali
Rohár)
- Mask all interrupts when unbinding host controller driver (Pali
Rohár)
- Fix memory leak in host controller unbind (Pali Rohár)
- Assert PERST# when unbinding host controller driver (Pali Rohár)
- Disable link training when unbinding host controller driver (Pali
Rohár)
- Disable common PHY when unbinding host controller driver (Pali
Rohár)
- Fix resource type checking to check only IORESOURCE_MEM, not
IORESOURCE_MEM_64, which is a flavor of IORESOURCE_MEM (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Implement pci_remap_iospace() for ARM so mvebu can use
devm_pci_remap_iospace() instead of the previous ARM-specific
pci_ioremap_io() interface (Pali Rohár)
- Use the standard pci_host_probe() instead of the device-specific
mvebu_pci_host_probe() (Pali Rohár)
- Replace all uses of ARM-specific pci_ioremap_io() with the ARM
implementation of the standard pci_remap_iospace() interface and
remove pci_ioremap_io() (Pali Rohár)
- Skip initializing invalid Root Ports (Pali Rohár)
- Check for errors from pci_bridge_emul_init() (Pali Rohár)
- Ignore any bridges at non-zero function numbers (Pali Rohár)
- Return ~0 data for invalid config read size (Pali Rohár)
- Disallow mapping interrupts on emulated bridges (Pali Rohár)
- Clear Root Port Memory & I/O Space Enable and Bus Master Enable at
initialization (Pali Rohár)
- Make type bits in Root Port I/O Base register read-only (Pali
Rohár)
- Disable Root Port windows when base/limit set to invalid values
(Pali Rohár)
- Set controller to Root Complex mode (Pali Rohár)
- Set Root Port Class Code to PCI Bridge (Pali Rohár)
- Update emulated Root Port secondary bus numbers to better reflect
the actual topology (Pali Rohár)
- Add PCI_BRIDGE_CTL_BUS_RESET support to emulated Root Ports so
pci_reset_secondary_bus() can reset connected devices (Pali Rohár)
- Add PCI_EXP_DEVCTL Error Reporting Enable support to emulated Root
Ports (Pali Rohár)
- Add PCI_EXP_RTSTA PME Status bit support to emulated Root Ports
(Pali Rohár)
- Add DEVCAP2, DEVCTL2 and LNKCTL2 support to emulated Root Ports on
Armada XP and newer devices (Pali Rohár)
- Export mvebu-mbus.c symbols to allow pci-mvebu.c to be a module
(Pali Rohár)
- Add support for compiling as a module (Pali Rohár)
MediaTek PCIe controller driver:
- Assert PERST# for 100ms to allow power and clock to stabilize
(qizhong cheng)
MediaTek PCIe Gen3 controller driver:
- Disable Mediatek DVFSRC voltage request since lack of DVFSRC to
respond to the request causes failure to exit L1 PM Substate
(Jianjun Wang)
MediaTek MT7621 PCIe controller driver:
- Declare mt7621_pci_ops static (Sergio Paracuellos)
- Give pcibios_root_bridge_prepare() access to host bridge windows
(Sergio Paracuellos)
- Move MIPS I/O coherency unit setup from driver to
pcibios_root_bridge_prepare() (Sergio Paracuellos)
- Add missing MODULE_LICENSE() (Sergio Paracuellos)
- Allow COMPILE_TEST for all arches (Sergio Paracuellos)
Microsoft Hyper-V host bridge driver:
- Add hv-internal interfaces to encapsulate arch IRQ dependencies
(Sunil Muthuswamy)
- Add arm64 Hyper-V vPCI support (Sunil Muthuswamy)
Qualcomm PCIe controller driver:
- Undo PM setup in qcom_pcie_probe() error handling path (Christophe
JAILLET)
- Use __be16 type to store return value from cpu_to_be16()
(Manivannan Sadhasivam)
- Constify static dw_pcie_ep_ops (Rikard Falkeborn)
Renesas R-Car PCIe controller driver:
- Fix aarch32 abort handler so it doesn't check the wrong bus clock
before accessing the host controller (Marek Vasut)
TI Keystone PCIe controller driver:
- Add register offset for ti,syscon-pcie-id and ti,syscon-pcie-mode
DT properties (Kishon Vijay Abraham I)
MicroSemi Switchtec management driver:
- Add Gen4 automotive device IDs (Kelvin Cao)
- Declare state_names[] as static so it's not allocated and
initialized for every call (Kelvin Cao)
Host controller driver cleanups:
- Use of_device_get_match_data(), not of_match_device(), when we only
need the device data in altera, artpec6, cadence, designware-plat,
dra7xx, keystone, kirin (Fan Fei)
- Drop pointless of_device_get_match_data() cast in j721e (Bjorn
Helgaas)
- Drop redundant struct device * from j721e since struct cdns_pcie
already has one (Bjorn Helgaas)
- Rename driver structs to *_pcie in intel-gw, iproc, ls-gen4,
mediatek-gen3, microchip, mt7621, rcar-gen2, tegra194, uniphier,
xgene, xilinx, xilinx-cpm for consistency across drivers (Fan Fei)
- Fix invalid address space conversions in hisi, spear13xx (Bjorn
Helgaas)
Miscellaneous:
- Sort Intel Device IDs by value (Andy Shevchenko)
- Change Capability offsets to hex to match spec (Baruch Siach)
- Correct misspellings (Krzysztof Wilczyński)
- Terminate statement with semicolon in pci_endpoint_test.c (Ming
Wang)"
* tag 'pci-v5.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (151 commits)
PCI: mt7621: Allow COMPILE_TEST for all arches
PCI: mt7621: Add missing MODULE_LICENSE()
PCI: mt7621: Move MIPS setup to pcibios_root_bridge_prepare()
PCI: Let pcibios_root_bridge_prepare() access bridge->windows
PCI: mt7621: Declare mt7621_pci_ops static
PCI: brcmstb: Do not turn off WOL regulators on suspend
PCI: brcmstb: Add control of subdevice voltage regulators
PCI: brcmstb: Add mechanism to turn on subdev regulators
PCI: brcmstb: Split brcm_pcie_setup() into two funcs
dt-bindings: PCI: Add bindings for Brcmstb EP voltage regulators
dt-bindings: PCI: Correct brcmstb interrupts, interrupt-map.
PCI: brcmstb: Fix function return value handling
PCI: brcmstb: Do not use __GENMASK
PCI: brcmstb: Declare 'used' as bitmap, not unsigned long
PCI: hv: Add arm64 Hyper-V vPCI support
PCI: hv: Make the code arch neutral by adding arch specific interfaces
PCI: pciehp: Use down_read/write_nested(reset_lock) to fix lockdep errors
x86/PCI: Remove initialization of static variables to false
PCI: Use DWORD accesses for LTR, L1 SS to avoid erratum
misc: pci_endpoint_test: Terminate statement with semicolon
...
find_first{,_zero}_bit is a more effective analogue of 'next' version if
start == 0. This patch replaces 'next' with 'first' where things look
trivial.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
- added MIPS support for brcmstb PCIe controller
- added Loongson 2K1000 reset driver
- removed board support for rbtx4938/rbtx4939
- removed support for TX4939 SoCs
- fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=wsIG
-----END PGP SIGNATURE-----
Merge tag 'mips_5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- add support for more BCM47XX based devices
- add MIPS support for brcmstb PCIe controller
- add Loongson 2K1000 reset driver
- remove board support for rbtx4938/rbtx4939
- remove support for TX4939 SoCs
- fixes and cleanups
* tag 'mips_5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (59 commits)
MIPS: ath79: drop _machine_restart again
PCI: brcmstb: Augment driver for MIPs SOCs
MIPS: bmips: Remove obsolete DMA mapping support
MIPS: bmips: Add support PCIe controller device nodes
dt-bindings: PCI: Add compatible string for Brcmstb 74[23]5 MIPs SOCs
MIPS: compressed: Fix build with ZSTD compression
MIPS: BCM47XX: Add support for Netgear WN2500RP v1 & v2
MIPS: BCM47XX: Add support for Netgear R6300 v1
MIPS: BCM47XX: Add LEDs and buttons for Asus RTN-10U
MIPS: BCM47XX: Add board entry for Linksys WRT320N v1
MIPS: BCM47XX: Define Linksys WRT310N V2 buttons
MIPS: Remove duplicated include in local.h
MIPS: retire "asm/llsc.h"
MIPS: rework local_t operation on MIPS64
MIPS: fix local_{add,sub}_return on MIPS64
mips/pci: remove redundant ret variable
MIPS: Loongson64: Add missing of_node_put() in ls2k_reset_init()
MIPS: new Kconfig option ZBOOT_LOAD_ADDRESS
MIPS: enable both vmlinux.gz.itb and vmlinuz for generic
MIPS: signal: Return immediately if call fails
...
Treewide cleanup and consolidation of MSI interrupt handling in
preparation for further changes in this area which are necessary to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space
-----BEGIN PGP SIGNATURE-----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=vKzd
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI irq updates from Thomas Gleixner:
"Rework of the MSI interrupt infrastructure.
This is a treewide cleanup and consolidation of MSI interrupt handling
in preparation for further changes in this area which are necessary
to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space"
* tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
genirq/msi: Populate sysfs entry only once
PCI/MSI: Unbreak pci_irq_get_affinity()
genirq/msi: Convert storage to xarray
genirq/msi: Simplify sysfs handling
genirq/msi: Add abuse prevention comment to msi header
genirq/msi: Mop up old interfaces
genirq/msi: Convert to new functions
genirq/msi: Make interrupt allocation less convoluted
platform-msi: Simplify platform device MSI code
platform-msi: Let core code handle MSI descriptors
bus: fsl-mc-msi: Simplify MSI descriptor handling
soc: ti: ti_sci_inta_msi: Remove ti_sci_inta_msi_domain_free_irqs()
soc: ti: ti_sci_inta_msi: Rework MSI descriptor allocation
NTB/msi: Convert to msi_on_each_desc()
PCI: hv: Rework MSI handling
powerpc/mpic_u3msi: Use msi_for_each-desc()
powerpc/fsl_msi: Use msi_for_each_desc()
powerpc/pasemi/msi: Convert to msi_on_each_dec()
powerpc/cell/axon_msi: Convert to msi_on_each_desc()
powerpc/4xx/hsta: Rework MSI handling
...
- Add PCI_ERROR_RESPONSE and related definitions for signaling and checking
for transaction errors on PCI (Naveen Naidu)
- Fabricate PCI_ERROR_RESPONSE data (~0) in config read wrappers, instead
of in host controller drivers, when transactions fail on PCI (Naveen
Naidu)
- Use PCI_POSSIBLE_ERROR() to check for possible failure of config reads
(Naveen Naidu)
* pci/errors:
PCI: xgene: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: hv: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: keystone: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: cpqphp: Use PCI_POSSIBLE_ERROR() to check config reads
PCI/PME: Use PCI_POSSIBLE_ERROR() to check config reads
PCI/DPC: Use PCI_POSSIBLE_ERROR() to check config reads
PCI: pciehp: Use PCI_POSSIBLE_ERROR() to check config reads
PCI: vmd: Use PCI_POSSIBLE_ERROR() to check config reads
PCI/ERR: Use PCI_POSSIBLE_ERROR() to check config reads
PCI: rockchip-host: Drop error data fabrication when config read fails
PCI: rcar-host: Drop error data fabrication when config read fails
PCI: altera: Drop error data fabrication when config read fails
PCI: mvebu: Drop error data fabrication when config read fails
PCI: aardvark: Drop error data fabrication when config read fails
PCI: kirin: Drop error data fabrication when config read fails
PCI: histb: Drop error data fabrication when config read fails
PCI: exynos: Drop error data fabrication when config read fails
PCI: mediatek: Drop error data fabrication when config read fails
PCI: iproc: Drop error data fabrication when config read fails
PCI: thunder: Drop error data fabrication when config read fails
PCI: Drop error data fabrication when config read fails
PCI: Use PCI_SET_ERROR_RESPONSE() for disconnected devices
PCI: Set error response data when config read fails
PCI: Add PCI_ERROR_RESPONSE and related definitions
- Sort Intel Device IDs by value (Andy Shevchenko)
- Change Capability offsets to hex to match spec (Baruch Siach)
- Correct misspellings (Krzysztof Wilczyński)
- Terminate statement with semicolon in pci_endpoint_test.c (Ming Wang)
* pci/misc:
misc: pci_endpoint_test: Terminate statement with semicolon
PCI: Correct misspelled words
PCI: Change capability register offsets to hex
PCI: Sort Intel Device IDs by value
- Make emulated ROM BAR read-only by default (Pali Rohár)
- Make some emulated legacy PCI bits read-only for PCIe devices (Pali
Rohár)
- Update reserved bits in emulated PCIe Capability (Pali Rohár)
- Allow drivers to emulate different PCIe Capability versions (Pali Rohár)
- Set emulated Capabilities List bit for all PCIe devices, since they must
have at least a PCIe Capability (Pali Rohár)
* remotes/lorenzo/pci/bridge-emul:
PCI: pci-bridge-emul: Set PCI_STATUS_CAP_LIST for PCIe device
PCI: pci-bridge-emul: Correctly set PCIe capabilities
PCI: pci-bridge-emul: Fix definitions of reserved bits
PCI: pci-bridge-emul: Properly mark reserved PCIe bits in PCI config space
PCI: pci-bridge-emul: Make expansion ROM Base Address register read-only
- Declare bitmap correctly and as part of struct nwl_msi managed resource
(Christophe JAILLET)
* remotes/lorenzo/pci/xilinx-nwl:
PCI: xilinx-nwl: Simplify code and fix a memory leak
- Use bitmap ops for MSI allocator (Christophe JAILLET)
- Fix IB window setup, which was broken by the fact that IB resources are
now sorted in address order instead of DT dma-ranges order (Rob Herring)
* remotes/lorenzo/pci/xgene:
PCI: xgene: Fix IB window setup
PCI: xgene-msi: Use bitmap_zalloc() when applicable
- Reset everything below VMD before enumerating to work around failure to
enumerate NVMe devices when guest OS reboots (Nirmal Patel)
- Honor platform ACPI _OSC feature negotiation for Root Ports below VMD
(Kai-Heng Feng)
- Add support for Raptor Lake SKUs (Karthik L Gopalakrishnan)
* remotes/lorenzo/pci/vmd:
PCI: vmd: Add DID 8086:A77F for all Intel Raptor Lake SKU's
PCI: vmd: Honor ACPI _OSC on PCIe features
PCI: vmd: Clean up domain before enumeration
- Fix aarch32 abort handler so it doesn't check the wrong bus clock before
accessing the host controller (Marek Vasut)
* remotes/lorenzo/pci/rcar:
PCI: rcar: Check if device is runtime suspended instead of __clk_is_enabled()
- Undo PM setup in qcom_pcie_probe() error handling path (Christophe
JAILLET)
- Use __be16 type to store return value from cpu_to_be16() (Manivannan
Sadhasivam)
- Constify static dw_pcie_ep_ops (Rikard Falkeborn)
* remotes/lorenzo/pci/qcom:
PCI: qcom-ep: Constify static dw_pcie_ep_ops
PCI: qcom: Use __be16 type to store return value from cpu_to_be16()
PCI: qcom: Fix an error handling path in 'qcom_pcie_probe()'
- Implement pci_remap_iospace() for ARM so mvebu can use
devm_pci_remap_iospace() instead of the previous ARM-specific
pci_ioremap_io() interface (Pali Rohár)
- Use the standard pci_host_probe() instead of the device-specific
mvebu_pci_host_probe() (Pali Rohár)
- Replace all uses of ARM-specific pci_ioremap_io() with the
ARM implementation of the standard pci_remap_iospace() interface and
remove pci_ioremap_io() (Pali Rohár)
- Skip initializing invalid Root Ports (Pali Rohár)
- Check for errors from pci_bridge_emul_init() (Pali Rohár)
- Ignore any bridges at non-zero function numbers (Pali Rohár)
- Return ~0 data for invalid config read size (Pali Rohár)
- Disallow mapping interrupts on emulated bridges (Pali Rohár)
- Clear Root Port Memory & I/O Space Enable and Bus Master Enable at
initialization (Pali Rohár)
- Make type bits in Root Port I/O Base register read-only (Pali Rohár)
- Disable Root Port windows when base/limit set to invalid values (Pali
Rohár)
- Set controller to Root Complex mode (Pali Rohár)
- Set Root Port Class Code to PCI Bridge (Pali Rohár)
- Update emulated Root Port secondary bus numbers to better reflect the
actual topology (Pali Rohár)
- Add PCI_BRIDGE_CTL_BUS_RESET support to emulated Root Ports so
pci_reset_secondary_bus() can reset connected devices (Pali Rohár)
- Add PCI_EXP_DEVCTL Error Reporting Enable support to emulated Root Ports
(Pali Rohár)
- Add PCI_EXP_RTSTA PME Status bit support to emulated Root Ports (Pali
Rohár)
- Add DEVCAP2, DEVCTL2 and LNKCTL2 support to emulated Root Ports on Armada
XP and newer devices (Pali Rohár)
- Export mvebu-mbus.c symbols to allow pci-mvebu.c to be a module (Pali
Rohár)
- Add support for compiling as a module (Pali Rohár)
* remotes/lorenzo/pci/mvebu:
PCI: mvebu: Add support for compiling driver as module
bus: mvebu-mbus: Export symbols for public API window functions
PCI: mvebu: Fix support for DEVCAP2, DEVCTL2 and LNKCTL2 registers on emulated bridge
PCI: mvebu: Fix support for PCI_EXP_RTSTA on emulated bridge
PCI: mvebu: Fix support for PCI_EXP_DEVCTL on emulated bridge
PCI: mvebu: Fix support for PCI_BRIDGE_CTL_BUS_RESET on emulated bridge
PCI: mvebu: Fix configuring secondary bus of PCIe Root Port via emulated bridge
PCI: mvebu: Set PCI Bridge Class Code to PCI Bridge
PCI: mvebu: Setup PCIe controller to Root Complex mode
PCI: mvebu: Propagate errors when updating PCI_IO_BASE and PCI_MEM_BASE registers
PCI: mvebu: Do not modify PCI IO type bits in conf_write
PCI: mvebu: Fix support for bus mastering and PCI_COMMAND on emulated bridge
PCI: mvebu: Disallow mapping interrupts on emulated bridges
PCI: mvebu: Handle invalid size of read config request
PCI: mvebu: Check that PCI bridge specified in DT has function number zero
PCI: mvebu: Check for errors from pci_bridge_emul_init() call
PCI: mvebu: Check for valid ports
arm: ioremap: Remove unused ARM-specific function pci_ioremap_io()
arm: ioremap: Replace pci_ioremap_io() usage by pci_remap_iospace()
PCI: mvebu: Remove custom mvebu_pci_host_probe() function
PCI: mvebu: Replace pci_ioremap_io() usage by devm_pci_remap_iospace()
arm: ioremap: Implement standard PCI function pci_remap_iospace()
- Disable Mediatek DVFSRC voltage request since lack of DVFSRC to respond
to the request causes failure to exit L1 PM Substate (Jianjun Wang)
* remotes/lorenzo/pci/mediatek-gen3:
PCI: mediatek-gen3: Disable DVFSRC voltage request
- Assert PERST# for 100ms to allow power and clock to stabilize (qizhong
cheng)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Assert PERST# for 100ms for power and clock to stabilize
- Add register offset for ti,syscon-pcie-id and ti,syscon-pcie-mode DT
properties (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/keystone:
PCI: keystone: Use phandle argument from "ti,syscon-pcie-id"/"ti,syscon-pcie-mode"
dt-bindings: PCI: ti,am65: Fix "ti,syscon-pcie-id"/"ti,syscon-pcie-mode" to take argument
- Don't ioremap NULL when DT lacks ATU resource (Tim Harvey)
- Drop redundant qcom-ep error message for platform_get_irq_byname()
failure (Krzysztof Wilczyński)
- Add i.MX8MM support (Richard Zhu)
- Use DWC common ops instead of layerscape-specific link-up functions (Hou
Zhiqiang)
* remotes/lorenzo/pci/dwc:
PCI: layerscape: Change to use the DWC common link-up check function
PCI: imx: Add the imx8mm pcie support
dt-bindings: imx6q-pcie: Add PHY phandles and name properties
PCI: qcom-ep: Remove surplus dev_err() when using platform_get_irq_byname()
PCI: dwc: Do not remap invalid res
- Declare bitmap correctly for use by bitmap interfaces (Christophe
JAILLET)
- Clean up computation of legacy and non-legacy MSI bitmasks (Florian
Fainelli)
- Update suspend/resume/remove error handling to warn about errors and not
fail the operation (Jim Quinlan)
- Correct the "pcie" and "msi" interrupt descriptions in DT binding (Jim
Quinlan)
- Add DT bindings for endpoint voltage regulators (Jim Quinlan)
- Split brcm_pcie_setup() into two functions (Jim Quinlan)
- Add mechanism for turning on voltage regulators for connected devices
(Jim Quinlan)
- Turn voltage regulators for connected devices on/off when bus is added or
removed (Jim Quinlan)
- When suspending, don't turn off voltage regulators for wakeup devices
(Jim Quinlan)
* pci/host/brcmstb:
PCI: brcmstb: Do not turn off WOL regulators on suspend
PCI: brcmstb: Add control of subdevice voltage regulators
PCI: brcmstb: Add mechanism to turn on subdev regulators
PCI: brcmstb: Split brcm_pcie_setup() into two funcs
dt-bindings: PCI: Add bindings for Brcmstb EP voltage regulators
dt-bindings: PCI: Correct brcmstb interrupts, interrupt-map.
PCI: brcmstb: Fix function return value handling
PCI: brcmstb: Do not use __GENMASK
PCI: brcmstb: Declare 'used' as bitmap, not unsigned long
Since all MIPS-specific code has been removed from driver, allow it to be
enabled for COMPILE_TEST on all architectures.
Mark it as tristate and remove MIPS the MIPS dependency.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The MT7621 PCIe host controller driver can be built as a module, but it
lacks a MODULE_LICENSE(), which causes a build error:
ERROR: modpost: missing MODULE_LICENSE() in drivers/pci/controller/pcie-mt7621.o
Add MODULE_LICENSE() to the driver.
Fixes: 2bdd5238e7 ("PCI: mt7621: Add MediaTek MT7621 PCIe host controller driver")
Link: https://lore.kernel.org/r/20211207104924.21327-5-sergio.paracuellos@gmail.com
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
On the MIPS ralink mt7621 platform, we need to set up I/O coherency units
based on the host bridge apertures.
To remove this arch dependency from the driver itself, move the coherency
setup from the driver to pcibios_root_bridge_prepare().
[bhelgaas: squash add/remove into one patch, commit log]
Link: https://lore.kernel.org/r/20211207104924.21327-3-sergio.paracuellos@gmail.com
Link: https://lore.kernel.org/r/20211207104924.21327-4-sergio.paracuellos@gmail.com
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net> # arch/mips
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> # arch/mips
Sparse complains about mt7621_pci_ops symbol is not declared and asks if
it should be declared as static instead. Sparse is right. Hence declare
symbol as static.
Link: https://lore.kernel.org/r/20211117152952.12271-1-sergio.paracuellos@gmail.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
If any downstream device can be a wakeup device, do not turn off the
regulators as the device will need them on.
Link: https://lore.kernel.org/r/20220106160332.2143-8-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This Broadcom STB PCIe RC driver has one port and connects directly to one
device, be it a switch or an endpoint. We want to be able to leverage the
recently added mechanism that allocates and turns on/off subdevice
regulators.
All that needs to be done is to put the regulator DT nodes in the bridge
below host and to set the pci_ops methods add_bus and remove_bus.
Note that the pci_subdev_regulators_add_bus() method is wrapped for two
reasons:
1. To achieve link up after the voltage regulators are turned on.
2. If, in the case of an unsuccessful link up, to redirect any PCIe
accesses to subdevices, e.g. the scan for DEV/ID. This redirection
is needed because the Broadcom PCIe HW will issue a CPU abort if such
an access is made when the link is down.
[bhelgaas: fold in
https://lore.kernel.org/r/20220112013100.48029-1-jim2101024@gmail.com]
Link: https://lore.kernel.org/r/20220106160332.2143-7-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a mechanism to identify standard PCIe regulators in the DT, allocate
them, and turn them on before the rest of the bus is scanned during
pci_host_probe().
The allocated structure that contains the regulators is stored in the port
driver dev.driver_data field. Here is a point-by-point of how and when
this mechanism is activated:
If:
-- PCIe RC driver sets pci_ops {add,remove)_bus to
pci_subdev_regulators_{add,remove}_bus during its probe.
-- There is a DT node "RB" under the host bridge DT node.
-- During the RC driver's pci_host_probe() the add_bus callback
is invoked where (bus->parent && pci_is_root_bus(bus->parent)
is true
Then:
-- A struct subdev_regulators structure will be allocated and
assigned to bus->dev.driver_data.
-- regulator_bulk_{get,enable} will be invoked on &bus->dev
and the former will search for and process any
vpcie{12v,3v3,3v3aux}-supply properties that reside in node "RB".
-- The regulators will be turned off/on for any unbind/bind operations.
-- The regulators will be turned off/on for any suspend/resumes, but
only if the RC driver handles this on its own. This will appear
in a later commit for the pcie-brcmstb.c driver.
The unabridged reason for doing this is as follows. We would like the
Broadcom STB PCIe root complex driver (and others) to be able to turn
off/on regulators[1] that provide power to endpoint[2] devices. Typically,
the drivers of these endpoint devices are stock Linux drivers that are not
aware that these regulator(s) exist and must be turned on for the driver to
be probed. The simple solution of course is to turn these regulators on at
boot and keep them on. However, this solution does not satisfy at least
three of our usage modes:
1. For example, one customer uses multiple PCIe controllers, but wants
the ability to, by script invoking and unbind, turn any or all of them
and their subdevices off to save power, e.g. when in battery mode.
2. Another example is when a watchdog script discovers that an endpoint
device is in an unresponsive state and would like to unbind, power
toggle, and re-bind just the PCIe endpoint and controller.
3. Of course we also want power turned off during suspend mode. However,
some endpoint devices may be able to "wake" during suspend and we need
to recognise this case and veto the nominal act of turning off its
regulator. Such is the case with Wake-on-LAN and Wake-on-WLAN support
where the PCIe endpoint device needs to be kept powered on in order to
receive network packets and wake the system.
In all of these cases it is advantageous for the PCIe controller to govern
the turning off/on the regulators needed by the endpoint device. The first
two cases can be done by simply unbinding and binding the PCIe controller,
if the controller has control of these regulators.
[1] These regulators typically govern the actual power supply to the
endpoint chip. Sometimes they may be the official PCIe socket
power -- such as 3.3v or aux-3.3v. Sometimes they are truly
the regulator(s) that supply power to the EP chip.
[2] The 99% configuration of our boards is a single endpoint device
attached to the PCIe controller. I use the term endpoint but it could
possibly mean a switch as well.
Link: https://lore.kernel.org/r/20220106160332.2143-6-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We need to take some code in brcm_pcie_setup() and put it in a new function
brcm_pcie_linkup(). In future commits the brcm_pcie_linkup() function will
be called indirectly by pci_host_probe() as opposed to the host driver
invoking it directly.
Some code that was executed after the PCIe linkup is now placed so that it
executes prior to linkup, since this code has to run prior to the
invocation of pci_host_probe().
Link: https://lore.kernel.org/r/20220106160332.2143-5-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Do at least a dev_err() on some calls to reset_control_rearm() and
brcm_phy_stop(). In some cases it may not make sense to return this error
value "above" as doing so will cause more trouble than is warranted.
Link: https://lore.kernel.org/r/20220106160332.2143-2-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Define the legacy MSI interrupt bitmask as well as the non-legacy interrupt
bitmask using GENMASK and then use them in brcm_msi_set_regs() in place of
__GENMASK().
Link: https://lore.kernel.org/r/20211122190459.3189616-1-f.fainelli@gmail.com
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
The 'used' field of 'struct brcm_msi' is used as a bitmap. Declare it with
DECLARE_BITMAP() and adjust users accordingly.
This fixes a harmless Coverity warning about array vs singleton usage.
This bitmap can be used for either legacy or MSI interrupts, which require
a size of BRCM_INT_PCI_MSI_LEGACY_NR or BRCM_INT_PCI_MSI_NR respectively.
Add a BUILD_BUG_ON() to ensure it is large enough.
Suggested-by: Krzysztof Wilczynski <kw@linux.com>
Addresses-Coverity: "Out-of-bounds access (ARRAY_VS_SINGLETON)"
Link: https://lore.kernel.org/r/e6d9da2112aab2939d1507b90962d07bfd735b4c.1636273671.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Add arm64 Hyper-V vPCI support by implementing the arch specific
interfaces. Introduce an IRQ domain and chip specific to Hyper-v vPCI that
is based on SPIs. The IRQ domain parents itself to the arch GIC IRQ domain
for basic vector management.
[bhelgaas: squash in fix from Yang Li <yang.lee@linux.alibaba.com>:
https://lore.kernel.org/r/20220112003324.62755-1-yang.lee@linux.alibaba.com]
Link: https://lore.kernel.org/r/1641411156-31705-3-git-send-email-sunilmut@linux.microsoft.com
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Encapsulate arch dependencies in Hyper-V vPCI through a set of
arch-dependent interfaces. Adding these arch specific interfaces will
allow for an implementation for other architectures, such as arm64.
There are no functional changes expected from this patch.
Link: https://lore.kernel.org/r/1641411156-31705-2-git-send-email-sunilmut@linux.microsoft.com
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
The current brcmstb driver works for Arm and Arm64. A few things are
modified here for us to support MIPs as well.
o There are four outbound range register groups and each directs a window
of up to 128MB. Even though there are four 128MB DT "ranges" in the
bmips PCIe DT node, these ranges are contiguous and are collapsed into
a single range by the OF range parser. Now the driver assumes a single
range -- for MIPs only -- and splits it back into 128MB sizes.
o For bcm7425, the config space accesses must be 32-bit reads or
writes. In addition, the 4k config space register array is missing
and not used.
o The registers for the upper 32-bits of the outbound window address do
not exist.
o Burst size must be set to 256 (this refers to an internal bus).
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fix a number of misspelled words, and while at it, correct two phrases used
to indicate a status of an operation where words used have been cleverly
truncated and thus always trigger a spellchecking error while performing a
static code analysis over the PCI tree.
[bhelgaas: reverse sense of quirk ternary]
Link: https://lore.kernel.org/r/20220107225942.121484-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Get "syscon" pcie_mode and pcie_id offset from the argument of
"ti,syscon-pcie-id" and "ti,syscon-pcie-mode" phandle respectively.
Previously a subnode to "syscon" node was added which has the
exact memory mapped address of pcie_mode and pcie_id but now the
offset of pcie_mode and pcie_id within "syscon" is now being passed
as argument to "ti,syscon-pcie-id" and "ti,syscon-pcie-mode" phandle.
If the offset is not provided in "ti,syscon-pcie-id"/"ti,syscon-pcie-mode",
the full memory mapped address of pcie_ctrl is used in order to maintain
old DT compatibility.
Similar change for J721E is as discussed in [1]
[1] -> http://lore.kernel.org/r/CAL_JsqKiUcO76bo1GoepWM1TusJWoty_BRy2hFSgtEVMqtrvvQ@mail.gmail.com
Link: https://lore.kernel.org/r/20211126083119.16570-3-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Described in PCIe CEM specification sections 2.2 (PERST# Signal) and
2.2.1 (Initial Power-Up (G3 to S0)). The deassertion of PERST# should
be delayed 100ms (TPVPERL) for the power and clock to become stable.
Link: https://lore.kernel.org/r/20211227133110.14500-1-qizhong.cheng@mediatek.com
Signed-off-by: qizhong cheng <qizhong.cheng@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Pali Rohár <pali@kernel.org>
Now when driver uses devm_pci_remap_iospace() function, it is possible
implement ->remove() callback for unbinding device from driver.
Implement mvebu_pcie_remove() callback with proper cleanup phase, drop
driver's suppress_bind_attrs flag and switch type of CONFIG_PCI_MVEBU
option from bool to tristate.
This allows to compile pci-mvebu.c driver as loadable module pci-mvebu.ko
with ability to unload it.
Link: https://lore.kernel.org/r/20211126144307.7568-3-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add support for this VMD device which supports the bus restriction mode.
The feature that turns off vector 0 for MSI-X remapping is also enabled.
Link: https://lore.kernel.org/r/20211217231211.46018-1-francisco.munoz.ruiz@linux.intel.com
Signed-off-by: Karthik L Gopalakrishnan <karthik.l.gopalakrishnan@intel.com>
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Jon Derrick <jonathan.derrick@linux.dev>
The current Layerscape PCIe driver directly uses the physical layer
LTSSM code to check the link-up state, which treats the > L0 states
as link-up. This is not correct, since there is not explicit map
between link-up state and LTSSM. So this patch changes to use the
DWC common link-up check function.
Link: https://lore.kernel.org/r/20211224094000.8513-1-Zhiqiang.Hou@nxp.com
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The only usage of pci_ep_ops is to assign its address to the ops field
in the dw_pcie_ep struct which is a pointer to const struct dw_pcie_ep_ops.
Make it const to allow the compiler to put it in read-only memory.
Link: https://lore.kernel.org/r/20211204220316.88655-1-rikard.falkeborn@gmail.com
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
When Samsung PCIe Gen4 NVMe is connected to Intel ADL VMD, the
combination causes AER message flood and drags the system performance
down.
The issue doesn't happen when VMD mode is disabled in BIOS, since AER
isn't enabled by acpi_pci_root_create() . When VMD mode is enabled, AER
is enabled regardless of _OSC:
[ 0.410076] acpi PNP0A08:00: _OSC: platform does not support [AER]
...
[ 1.486704] pcieport 10000:e0:06.0: AER: enabled with IRQ 146
Since VMD is an aperture to regular PCIe root ports, honor ACPI _OSC to
disable PCIe features accordingly to resolve the issue.
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=215027
Link: https://lore.kernel.org/r/20211203031541.1428904-1-kai.heng.feng@canonical.com
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Armada XP and new hardware supports access to DEVCAP2, DEVCTL2 and LNKCTL2
configuration registers of PCIe core via PCIE_CAP_PCIEXP. So export them
via emulated software root bridge.
Pre-XP hardware does not support these registers and returns zeros.
Link: https://lore.kernel.org/r/20211125124605.25915-16-pali@kernel.org
Fixes: 1f08673eef ("PCI: mvebu: Convert to PCI emulated bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PME Status bit in Root Status Register (PCIE_RC_RTSTA_OFF) is read-only and
can be cleared only by writing 0b to the Interrupt Cause RW0C register
(PCIE_INT_CAUSE_OFF).
Link: https://lore.kernel.org/r/20211125124605.25915-15-pali@kernel.org
Fixes: 1f08673eef ("PCI: mvebu: Convert to PCI emulated bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Comment in Armada 370 functional specification is misleading.
PCI_EXP_DEVCTL_*RE bits are supported and configures receiving of error
interrupts.
Link: https://lore.kernel.org/r/20211125124605.25915-14-pali@kernel.org
Fixes: 1f08673eef ("PCI: mvebu: Convert to PCI emulated bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Hardware supports PCIe Hot Reset via PCIE_CTRL_OFF register. Use it for
implementing PCI_BRIDGE_CTL_BUS_RESET bit of PCI_BRIDGE_CONTROL register on
emulated bridge.
With this change the function pci_reset_secondary_bus() starts working and
can reset connected PCIe card.
Link: https://lore.kernel.org/r/20211125124605.25915-13-pali@kernel.org
Fixes: 1f08673eef ("PCI: mvebu: Convert to PCI emulated bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
It looks like that mvebu PCIe controller has for each PCIe link fully
independent PCIe host bridge and so every PCIe Root Port is isolated not
only on its own bus but also isolated from each others. But in past device
tree structure was defined to put all PCIe Root Ports (as PCI Bridge
devices) into one root bus 0 and this bus is emulated by pci-mvebu.c
driver.
Probably reason for this decision was incorrect understanding of PCIe
topology of these Armada SoCs and also reason of misunderstanding how is
PCIe controller generating Type 0 and Type 1 config requests (it is fully
different compared to other drivers). Probably incorrect setup leaded to
very surprised things like having PCIe Root Port (PCI Bridge device, with
even incorrect Device Class set to Memory Controller) and the PCIe device
behind the Root Port on the same PCI bus, which obviously was needed to
somehow hack (as these two devices cannot be in reality on the same bus).
Properly set mvebu local bus number and mvebu local device number based on
PCI Bridge secondary bus number configuration. Also correctly report
configured secondary bus number in config space. And explain in driver
comment why this setup is correct.
Link: https://lore.kernel.org/r/20211125124605.25915-12-pali@kernel.org
Fixes: 1f08673eef ("PCI: mvebu: Convert to PCI emulated bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The default value of Class Code of this bridge corresponds to a Memory
controller, though. This is probably relict from the past when old
Marvell/Galileo PCI-based controllers were used as standalone PCI device
for connecting SDRAM or workaround for PCs with broken BIOS. Details are
in commit 36de23a4c5 ("MIPS: Cobalt: Explain GT64111 early PCI fixup").
Change the Class Code to correspond to a PCI Bridge.
Add comment explaining this change.
Link: https://lore.kernel.org/r/20211125124605.25915-11-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This driver operates only in Root Complex mode, so ensure that hardware is
properly configured in Root Complex mode.
Link: https://lore.kernel.org/r/20211125124605.25915-10-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Properly propagate failure from mvebu_pcie_add_windows() function back to
the caller mvebu_pci_bridge_emul_base_conf_write() and correctly updates
PCI_IO_BASE, PCI_MEM_BASE and PCI_IO_BASE_UPPER16 registers on error.
On error set base value higher than limit value which indicates that
address range is disabled. When IO is unsupported then let IO registers
zeroed as required by PCIe base specification.
Link: https://lore.kernel.org/r/20211125124605.25915-9-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PCI IO type bits are already initialized in mvebu_pci_bridge_emul_init()
function and only when IO support is enabled. These type bits are read-only
and pci-bridge-emul.c code already does not allow to modify them from upper
layers.
When IO support is disabled then all IO registers should be read-only and
return zeros. Therefore do not modify PCI IO type bits in
mvebu_pci_bridge_emul_base_conf_write() callback.
Link: https://lore.kernel.org/r/20211125124605.25915-8-pali@kernel.org
Fixes: 1f08673eef ("PCI: mvebu: Convert to PCI emulated bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
According to PCI specifications bits [0:2] of Command Register, this should
be by default disabled on reset. So explicitly disable these bits at early
beginning of driver initialization.
Also remove code which unconditionally enables all 3 bits and let kernel
code (via pci_set_master() function) to handle bus mastering of PCI Bridge
via emulated PCI_COMMAND on emulated bridge.
Adjust existing functions mvebu_pcie_handle_iobase_change() and
mvebu_pcie_handle_membase_change() to handle PCI_IO_BASE and PCI_MEM_BASE
registers correctly even when bus mastering on emulated bridge is disabled.
Link: https://lore.kernel.org/r/20211125124605.25915-7-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Interrupt support on mvebu emulated bridges is not implemented yet.
So properly indicate return value to callers that they cannot request
interrupts from emulated bridge.
Link: https://lore.kernel.org/r/20211125124605.25915-6-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Function mvebu_pcie_hw_rd_conf() does not handle invalid size. So correctly
set read value to all-ones and return appropriate error return value
PCIBIOS_BAD_REGISTER_NUMBER like in mvebu_pcie_hw_wr_conf() function.
Link: https://lore.kernel.org/r/20211125124605.25915-5-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Driver cannot handle PCI bridges at non-zero function address. So add
appropriate check. Currently all in-tree kernel DTS files set PCI bridge
function to zero.
Link: https://lore.kernel.org/r/20211125124605.25915-4-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Function pci_bridge_emul_init() may fail so correctly check for errors.
Link: https://lore.kernel.org/r/20211125124605.25915-3-pali@kernel.org
Fixes: 1f08673eef ("PCI: mvebu: Convert to PCI emulated bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Some mvebu ports do not have to be initialized. So skip these uninitialized
mvebu ports in every port iteration function to prevent access to unmapped
memory or dereferencing NULL pointers. Uninitialized mvebu port has base
address set to NULL.
Link: https://lore.kernel.org/r/20211125124605.25915-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The sparse checker complains about converting pointers between address
spaces. We correctly stored an __iomem pointer in struct spear13xx_pcie,
but discarded the __iomem when extracting app_base, causing one warning.
Then we passed the non-__iomem pointer to writel(), which expects an
__iomem pointer, causing another warning.
Add the appropriate annotations.
The sparse warnings look like this:
$ make C=2 drivers/pci/controller/
drivers/pci/controller/dwc/pcie-spear13xx.c:72:54: warning: incorrect type in initializer (different address spaces)
drivers/pci/controller/dwc/pcie-spear13xx.c:72:54: expected struct pcie_app_reg *app_reg
drivers/pci/controller/dwc/pcie-spear13xx.c:72:54: got void [noderef] __iomem *app_base
drivers/pci/controller/dwc/pcie-spear13xx.c:78:26: warning: incorrect type in argument 2 (different address spaces)
drivers/pci/controller/dwc/pcie-spear13xx.c:78:26: expected void volatile [noderef] __iomem *addr
drivers/pci/controller/dwc/pcie-spear13xx.c:78:26: got unsigned int *
Link: https://lore.kernel.org/r/20211223213749.1314142-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
The sparse checker complains about converting pointers between address
spaces. The pci_config_window.priv pointer is a generic void *, but
hisi_pcie_map_bus() needs a void __iomem *.
This isn't a problem in other drivers because they store the __iomem
pointer in a driver struct. Add a trivial struct hisi_pcie to avoid the
warning.
The sparse warning looks like this:
$ make C=2 drivers/pci/controller/
drivers/pci/controller/dwc/pcie-hisi.c:61:37: warning: incorrect type in initializer (different address spaces)
drivers/pci/controller/dwc/pcie-hisi.c:61:37: expected void [noderef] __iomem *reg_base
drivers/pci/controller/dwc/pcie-hisi.c:61:37: got void *priv
Link: https://lore.kernel.org/r/20211223213749.1314142-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Rename struct xilinx_cpm_pcie_port to xilinx_cpm_pcie to match the
convention of <driver>_pcie. No functional change intended.
Link: https://lore.kernel.org/r/20211223011054.1227810-24-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Rename struct xilinx_pcie_port to xilinx_pcie to match the convention of
<driver>_pcie. No functional change intended.
Link: https://lore.kernel.org/r/20211223011054.1227810-23-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Rename struct xgene_pcie_port to xgene_pcie to match the convention of
<driver>_pcie. No functional change intended.
Link: https://lore.kernel.org/r/20211223011054.1227810-22-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Toan Le <toan@os.amperecomputing.com>
Rename struct uniphier_pcie_priv to uniphier_pcie to match the convention
of <driver>_pcie. No functional change intended.
[bhelgaas: drop extraneous uniphier_pcie_irq_ack() from patch]
Link: https://lore.kernel.org/r/20211223011054.1227810-21-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Rename tegra_pcie_dw to tegra194_pcie to match the convention of
<driver>_pcie. No functional change intended.
[bhelgaas: rename functions similarly]
Link: https://lore.kernel.org/r/20211223011054.1227810-20-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Rename struct rcar_pci_priv to rcar_pci to match the convention of
<driver>_pci. No functional change intended.
Link: https://lore.kernel.org/r/20211223011054.1227810-19-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Rename mt7621_pci_* structs and functions to mt7621_pcie_* for consistency
with the rest of the file.
Link: https://lore.kernel.org/r/20211223011054.1227810-18-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Rename struct mc_port to mc_pcie to match the convention of <driver>_pcie.
No functional change intended.
Link: https://lore.kernel.org/r/20211223011054.1227810-16-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Daire McNamara <daire.mcnamara@microchip.com>
Rename struct mtk_pcie_port to mtk_gen3_pcie to match the convention of
<driver>_pcie. No functional change intended.
Link: https://lore.kernel.org/r/20211223011054.1227810-15-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Jianjun Wang <jianjun.wang@mediatek.com>
Rename iproc_pcie_pltfm_* to iproc_pltfm_pcie_* for consistency with other
drivers. No functional change intended.
Link: https://lore.kernel.org/r/20211223011054.1227810-13-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Rename iproc_pcie_bcma_* to iproc_bcma_pcie_* for consistency with other
drivers. No functional change intended.
Link: https://lore.kernel.org/r/20211223011054.1227810-12-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Rename struct intel_pcie_port to intel_pcie to match the convention of
<driver>_pcie. No functional change intended.
Link: https://lore.kernel.org/r/20211223011054.1227810-11-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rahul Tanwar <rtanwar@maxlinear.com>
The struct cdns_pcie already contains the struct device for the j721e PCIe
controller. There's no need to store another copy in struct j721e_pcie.
Remove the redundant copy from struct j721e_pcie.
Link: https://lore.kernel.org/r/20211223011054.1227810-10-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tom Joseph <tjoseph@cadence.com>
of_device_get_match_data() returns "void *", so no cast is needed when
assigning the result to a pointer type. Drop the unnecessary cast.
Link: https://lore.kernel.org/r/20211223011054.1227810-9-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tom Joseph <tjoseph@cadence.com>
The kirin driver only needs the device data, not the whole struct
of_device_id. Use of_device_get_match_data() instead of of_match_device().
No functional change intended.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211223011054.1227810-8-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
The keystone driver only needs the device data, not the whole struct
of_device_id. Use of_device_get_match_data() instead of of_match_device().
No functional change intended.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211223011054.1227810-7-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
The dra7xx driver only needs the device data, not the whole struct
of_device_id. Use of_device_get_match_data() instead of of_match_device().
No functional change intended.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211223011054.1227810-6-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
The designware-plat driver only needs the device data, not the whole struct
of_device_id. Use of_device_get_match_data() instead of of_match_device().
No functional change intended.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211223011054.1227810-5-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The cadence driver only needs the device data, not the whole struct
of_device_id. Use of_device_get_match_data() instead of of_match_device().
No functional change intended.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211223011054.1227810-4-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tom Joseph <tjoseph@cadence.com>
The artpec6 driver only needs the device data, not the whole struct
of_device_id. Use of_device_get_match_data() instead of of_match_device().
No functional change intended.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211223011054.1227810-3-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
The altera driver only needs the device data, not the whole struct
of_device_id. Use of_device_get_match_data() instead of of_match_device().
No functional change intended.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211223011054.1227810-2-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Joyce Ooi <joyce.ooi@intel.com>
i.MX8MM PCIe works mostly like the i.MX8MQ one, but has a different PHY
and allows to output the internal PHY reference clock via the refclk pad.
Add the i.MX8MM PCIe support based on the standalone PHY driver.
Link: https://lore.kernel.org/r/1640312885-31142-2-git-send-email-hongxing.zhu@nxp.com
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Replace the about to vanish iterators and make use of the filtering. Take
the descriptor lock around the iterators.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20211206210748.629363944@linutronix.de
The driver is not ready yet to be compiled as a module since it depends
on some symbols not exported on MIPS. We have the following current
problems:
Building mips:allmodconfig ... failed
--------------
Error log:
ERROR: modpost: missing MODULE_LICENSE() in drivers/pci/controller/pcie-mt7621.o
ERROR: modpost: "mips_cm_unlock_other" [drivers/pci/controller/pcie-mt7621.ko] undefined!
ERROR: modpost: "mips_cpc_base" [drivers/pci/controller/pcie-mt7621.ko] undefined!
ERROR: modpost: "mips_cm_lock_other" [drivers/pci/controller/pcie-mt7621.ko] undefined!
ERROR: modpost: "mips_cm_is64" [drivers/pci/controller/pcie-mt7621.ko] undefined!
ERROR: modpost: "mips_gcr_base" [drivers/pci/controller/pcie-mt7621.ko] undefined!
Temporarily move from 'tristate' to 'bool' until a better solution is
ready.
Also RALINK is redundant because SOC_MT7621 already depends on it.
Hence, simplify condition.
Fixes: 2bdd5238e7 ("PCI: mt7621: Add MediaTek MT7621 PCIe host controller driver").
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-and-Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=BWkT
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Revert emulation of Marvell Armada A3720 expansion ROM because it
doesn't work as expected (Marek Behún)
- Assert PERST# in Apple M1 driver to fix initialization when booting
from bootloaders using PCIe, such as U-Boot (Marc Zyngier)
- Describe PERST# as active low in Apple T8103 DT and update driver to
match (Marc Zyngier)
* tag 'pci-v5.16-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: apple: Fix PERST# polarity
arm64: dts: apple: t8103: Mark PCIe PERST# polarity active low in DT
PCI: apple: Follow the PCIe specifications when resetting the port
Revert "PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge"
Daniel Borkmann says:
====================
bpf 2021-12-08
We've added 12 non-merge commits during the last 22 day(s) which contain
a total of 29 files changed, 659 insertions(+), 80 deletions(-).
The main changes are:
1) Fix an off-by-two error in packet range markings and also add a batch of
new tests for coverage of these corner cases, from Maxim Mikityanskiy.
2) Fix a compilation issue on MIPS JIT for R10000 CPUs, from Johan Almbladh.
3) Fix two functional regressions and a build warning related to BTF kfunc
for modules, from Kumar Kartikeya Dwivedi.
4) Fix outdated code and docs regarding BPF's migrate_disable() use on non-
PREEMPT_RT kernels, from Sebastian Andrzej Siewior.
5) Add missing includes in order to be able to detangle cgroup vs bpf header
dependencies, from Jakub Kicinski.
6) Fix regression in BPF sockmap tests caused by missing detachment of progs
from sockets when they are removed from the map, from John Fastabend.
7) Fix a missing "no previous prototype" warning in x86 JIT caused by BPF
dispatcher, from Björn Töpel.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Add selftests to cover packet access corner cases
bpf: Fix the off-by-two error in range markings
treewide: Add missing includes masked by cgroup -> bpf dependency
tools/resolve_btfids: Skip unresolved symbol warning for empty BTF sets
bpf: Fix bpf_check_mod_kfunc_call for built-in modules
bpf: Make CONFIG_DEBUG_INFO_BTF depend upon CONFIG_BPF_SYSCALL
mips, bpf: Fix reference to non-existing Kconfig symbol
bpf: Make sure bpf_disable_instrumentation() is safe vs preemption.
Documentation/locking/locktypes: Update migrate_disable() bits.
bpf, sockmap: Re-evaluate proto ops when psock is removed from sockmap
bpf, sockmap: Attach map progs to psock early for feature probes
bpf, x86: Fix "no previous prototype" warning
====================
Link: https://lore.kernel.org/r/20211208155125.11826-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that PERST# is properly defined as active-low in the device tree, fix
the driver to correctly drive the line independently of the implied
polarity.
Suggested-by: Pali Rohár <pali@kernel.org>
Fixes: 1e33888fbe ("PCI: apple: Add initial hardware bring-up")
Link: https://lore.kernel.org/r/20211123180636.80558-4-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
While the Apple PCIe driver works correctly when directly booted from the
firmware, it fails to initialise when the kernel is booted from a
bootloader using PCIe such as u-boot.
That's because we're missing a proper reset of the port (we only clear the
reset, but never assert it).
The PCIe spec requirements are two-fold:
- PERST# must be asserted before setting up the clocks and stay asserted
for at least 100us (Tperst-clk)
- Once PERST# is deasserted, the OS must wait for at least 100ms "from
the end of a Conventional Reset" before we can start talking to the
devices
Implementing this results in a booting system.
[bhelgaas: #PERST -> PERST#, update spec references to current]
Fixes: 1e33888fbe ("PCI: apple: Add initial hardware bring-up")
Link: https://lore.kernel.org/r/20211123180636.80558-2-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Pali Rohár <pali@kernel.org>
Cc: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Older mvebu hardware provides PCIe Capability structure only in version 1.
New mvebu and aardvark hardware provides it in version 2. So do not force
version to 2 in pci_bridge_emul_init() and rather allow drivers to set
correct version. Drivers need to set version in pcie_conf.cap field without
overwriting PCI_CAP_LIST_ID register. Both drivers (mvebu and aardvark) do
not provide slot support yet, so do not set PCI_EXP_FLAGS_SLOT flag.
Link: https://lore.kernel.org/r/20211124155944.1290-6-pali@kernel.org
Fixes: 23a5fba4d9 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
REFCLK1 has req/ack bits that need to be programmed, just like REFCLK0.
Link: https://lore.kernel.org/r/20211117140044.193865-1-marcan@marcan.st
Fixes: 1e33888fbe ("PCI: apple: Add initial hardware bring-up")
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
cpu_to_be16() returns __be16 value but the driver uses u16 and that's
incorrect. Fix it by using __be16 as the data type of bdf_be variable.
The issue was spotted by the below sparse warning:
sparse warnings: (new ones prefixed by >>)
>> drivers/pci/controller/dwc/pcie-qcom.c:1305:30: sparse: sparse: incorrect type in initializer (different base types) @@ expected unsigned short [usertype] bdf_be @@ got restricted __be16 [usertype] @@
drivers/pci/controller/dwc/pcie-qcom.c:1305:30: sparse: expected unsigned short [usertype] bdf_be
drivers/pci/controller/dwc/pcie-qcom.c:1305:30: sparse: got restricted __be16 [usertype]
Link: https://lore.kernel.org/r/20211130080924.266116-1-manivannan.sadhasivam@linaro.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
IORESOURCE_MEM_64 is not a resource type but a type flag.
Remove incorrect check for type IORESOURCE_MEM_64.
Link: https://lore.kernel.org/r/20211125160148.26029-2-kabel@kernel.org
Fixes: 64f160e19e ("PCI: aardvark: Configure PCIe resources from 'ranges' DT property")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
cgroup.h (therefore swap.h, therefore half of the universe)
includes bpf.h which in turn includes module.h and slab.h.
Since we're about to get rid of that dependency we need
to clean things up.
v2: drop the cpu.h include from cacheinfo.h, it's not necessary
and it makes riscv sensitive to ordering of include files.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Acked-by: SeongJae Park <sj@kernel.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/all/20211120035253.72074-1-kuba@kernel.org/ # v1
Link: https://lore.kernel.org/all/20211120165528.197359-1-kuba@kernel.org/ # cacheinfo discussion
Link: https://lore.kernel.org/bpf/20211202203400.1208663-1-kuba@kernel.org
Disable the PCIe PHY when unbinding driver. This should save some power.
Link: https://lore.kernel.org/r/20211130172913.9727-12-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Disable link training circuit in driver unbind sequence. We want to
leave link training in the same state as it was before the driver was
probed.
Link: https://lore.kernel.org/r/20211130172913.9727-11-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Put the PCIe card into reset by asserting PERST# signal when unbinding
driver. It doesn't make sense to leave the card working if it can't
communicate with the host. This should also save some power.
Link: https://lore.kernel.org/r/20211130172913.9727-10-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Free config space for emulated root bridge when unbinding driver to fix
memory leak. Do it after disabling and masking all interrupts, since
aardvark interrupt handler accesses config space of emulated root
bridge.
Link: https://lore.kernel.org/r/20211130172913.9727-9-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Ensure that no interrupt can be triggered after driver unbind.
Link: https://lore.kernel.org/r/20211130172913.9727-8-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Ensure that after driver unbind PCIe cards are not able to forward
memory and I/O requests in the upstream direction.
Link: https://lore.kernel.org/r/20211130172913.9727-7-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add two more comments into the advk_pcie_remove() method.
Link: https://lore.kernel.org/r/20211130172913.9727-6-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
We already clear all the other interrupts (ISR0, ISR1, HOST_CTRL_INT).
Define a new macro PCIE_MSI_ALL_MASK and do the same clearing for MSIs,
to ensure that we don't start receiving spurious interrupts.
Use this new mask in advk_pcie_handle_msi();
Link: https://lore.kernel.org/r/20211130172913.9727-5-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PCI aardvark hardware supports access to DEVCAP2, DEVCTL2, LNKCAP2 and
LNKCTL2 configuration registers of PCIe core via PCIE_CORE_PCIEXP_CAP.
Export them via emulated software root bridge.
Link: https://lore.kernel.org/r/20211130172913.9727-4-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
On imx6 and perhaps others when pcie probes you get a:
imx6q-pcie 33800000.pcie: invalid resource
This occurs because the atu is not specified in the DT and as such it
should not be remapped.
Link: https://lore.kernel.org/r/20211101180243.23761-1-tharvey@gateworks.com
Fixes: 281f1f99cf ("PCI: dwc: Detect number of iATU windows")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
This reverts commit 239edf686c.
239edf686c ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated
bridge") added support for the Type 1 Expansion ROM BAR at config offset
0x38, based on the register being listed in the Marvell Armada A3720 spec.
But the spec doesn't document it at all for RC mode, and there is no ROM in
the SOC, so remove this emulation for now.
The PCI bridge which represents aardvark's PCIe Root Port has an Expansion
ROM Base Address register at offset 0x30, but its meaning is different than
PCI's Expansion ROM BAR register, although the layout is the same. (This
is why we thought it does the same thing.)
First: there is no ROM (or part of BootROM) in the A3720 SOC dedicated for
PCIe Root Port (or controller in RC mode) containing executable code that
would initialize the Root Port, suitable for execution in bootloader (this
is how Expansion ROM BAR is used on x86).
Second: in A3720 spec the register (address 0xD0070030) is not documented
at all for Root Complex mode, but similar to other BAR registers, it has an
"entangled partner" in register 0xD0075920, which does address translation
for the BAR in 0xD0070030:
- the BAR register sets the address from the view of PCIe bus
- the translation register sets the address from the view of the CPU
The other BAR registers also have this entangled partner, and they can be
used to:
- in RC mode: address-checking on the receive side of the RC (they can
define address ranges for memory accesses from remote Endpoints to the
RC)
- in Endpoint mode: allow the remote CPU to access memory on A3720
The Expansion ROM BAR has only the Endpoint part documented, but from the
similarities we think that it can also be used in RC mode in that way.
So either Expansion ROM BAR has different meaning (if the hypothesis above
is true), or we don't know it's meaning (since it is not documented for RC
mode).
Remove the register from the emulated bridge accessing functions.
[bhelgaas: summarize reason for removal (first paragraph)]
Fixes: 239edf686c ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge")
Link: https://lore.kernel.org/r/20211125160148.26029-3-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Now after pci_ioremap_io() usage was replaced by devm_pci_remap_iospace()
function, there is no need to use custom mvebu_pci_host_probe() function.
Current implementation of mvebu_pci_host_probe() is same as standard PCI
core function pci_host_probe(). So replace mvebu_pci_host_probe() call by
pci_host_probe() and remove custom mvebu_pci_host_probe() function.
Link: https://lore.kernel.org/r/20211124154116.916-4-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Replace __clk_is_enabled() with pm_runtime_suspended(),
as __clk_is_enabled() was checking the wrong bus clock
and caused the following build error too:
arm-linux-gnueabi-ld: drivers/pci/controller/pcie-rcar-host.o: in function `rcar_pcie_aarch32_abort_handler':
pcie-rcar-host.c:(.text+0xdd0): undefined reference to `__clk_is_enabled'
Link: https://lore.kernel.org/r/20211115204641.12941-1-marek.vasut@gmail.com
Fixes: a115b1bd3a ("PCI: rcar: Add L1 link state fix into data abort hook")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
During VT-d pass-through, the VMD driver occasionally fails to
enumerate underlying NVMe devices when repetitive reboots are
performed in the guest OS. The issue can be resolved by resetting
VMD root ports for proper enumeration and triggering secondary bus
reset which will also propagate reset through downstream bridges.
Link: https://lore.kernel.org/r/20211116221136.85134-1-nirmal.patel@linux.intel.com
Signed-off-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Jon Derrick <jonathan.derrick@linux.dev>
Allocate space for bitmap in struct nwl_msi at probe time instead of
dynamically allocating the memory at runtime.
This simplifies code (especially error handling paths) and avoid some
open-coded arithmetic in allocator arguments.
This also fixes a potential memory leak. The bitmap was never freed. It
is now part of a managed resource.
Link: https://lore.kernel.org/r/5483f10a44b06aad55728576d489adfa16c3be91.1636279388.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
These pokes are not required to make the PCIe port work, but it sounds
like this should save some power at least.
Link: https://lore.kernel.org/r/20211117141916.197192-1-marcan@marcan.st
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Commit 6dce5aa59e ("PCI: xgene: Use inbound resources for setup")
broke PCI support on XGene. The cause is the IB resources are now sorted
in address order instead of being in DT dma-ranges order. The result is
which inbound registers are used for each region are swapped. I don't
know the details about this h/w, but it appears that IB region 0
registers can't handle a size greater than 4GB. In any case, limiting
the size for region 0 is enough to get back to the original assignment
of dma-ranges to regions.
Link: https://lore.kernel.org/all/CA+enf=v9rY_xnZML01oEgKLmvY1NGBUUhnSJaETmXtDtXfaczA@mail.gmail.com/
Link: https://lore.kernel.org/r/20211129173637.303201-1-robh@kernel.org
Fixes: 6dce5aa59e ("PCI: xgene: Use inbound resources for setup")
Reported-by: Stéphane Graber <stgraber@ubuntu.com>
Tested-by: Stéphane Graber <stgraber@ubuntu.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: stable@vger.kernel.org # v5.5+
Now when ARM architecture code also provides standard PCI core function
pci_remap_iospace(), use its devm_pci_remap_iospace() variant in
pci-mvebu.c driver instead of old ARM-specific pci_ioremap_io() function.
Call devm_pci_remap_iospace() before adding IO resource to host bridge
structure, at the place where it should be.
Link: https://lore.kernel.org/r/20211124154116.916-3-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
'xgene_msi->bitmap' is a bitmap. So use 'bitmap_zalloc()' to simplify code,
improve the semantic and avoid some open-coded arithmetic in allocator
arguments.
Also change the corresponding 'kfree()' into 'bitmap_free()' to keep
consistency.
Link: https://lore.kernel.org/r/32f3bc1fbfbd6ee0815e565012904758ca9eff7e.1635019243.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
If 'of_device_get_match_data()' fails, previous 'pm_runtime_get_sync()/
pm_runtime_enable()' should be undone.
To fix it, the easiest is to move this block of code before the memory
allocations and the pm_runtime_xxx calls.
Link: https://lore.kernel.org/r/4d03c636193f64907c8dacb17fa71ed05fd5f60c.1636220582.git.christophe.jaillet@wanadoo.fr
Fixes: b89ff41025 ("PCI: qcom: Replace ops with struct pcie_cfg in pcie match data")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
When the DVFSRC (dynamic voltage and frequency scaling resource collector)
feature is not implemented, the PCIe hardware will assert a voltage request
signal when exit from the L1 PM Substates to request a specific Vcore
voltage, but cannot receive the voltage ready signal, which will cause
the link to fail to exit the L1 PM Substates.
Disable DVFSRC voltage request by default, we need to find a common way to
enable it in the future.
Link: https://lore.kernel.org/r/20211015063602.29058-1-jianjun.wang@mediatek.com
Fixes: d3bf75b579 ("PCI: mediatek-gen3: Add MediaTek Gen3 driver for MT8192")
Tested-by: Qizhong Cheng <qizhong.cheng@mediatek.com>
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
When config pci_ops.read() can detect failed PCI transactions, the data
returned to the CPU is PCI_ERROR_RESPONSE (~0 or 0xffffffff).
Obviously a successful PCI config read may *also* return that data if a
config register happens to contain ~0, so it doesn't definitively indicate
an error unless we know the register cannot contain ~0.
Use PCI_POSSIBLE_ERROR() to check the response we get when we read data
from hardware. This unifies PCI error response checking and makes error
checks consistent and easier to find.
Link: https://lore.kernel.org/r/ed01cad87a2e35f3865275b5fb34290817a1ebf8.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Derrick <jonathan.derrick@linux.dev>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/50f9a6fa16521a86cb24d2f27c1f66eb3568cb9a.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/83540eb3ae76a0d28bbe03d69d685a6d549b456b.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/ed5020e5b008b28c33a90c9c1670cef2393d3b7e.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/f30264b137b1282ffda34d336e8060bb13d60b98.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/335014f2b44cdf24ed1e37cb7c88f6c5de896cc2.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/f87e22bc09a471d2cf15ad05dfd6432f57739aed.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/7da7ea760abc5f85cad6e9b0d3e59eebd93f50d3.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/765c2f27d85fcee4eb137023dc0a8f864eee9e36.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/666127469482f9ca177805ff52aeb7bccb26e4c9.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/b95defa3db834789a4207df5d6b0216c8b610524.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/22f471b638276422926c49f3d42ac41bc7b28b3d.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
BMIPS_GENERIC denotes support for the MIPS-based Broadcom STB platforms
which this driver can support.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
-----BEGIN PGP SIGNATURE-----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=nsMh
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
- Use PCI_VENDOR_ID_AMCC macro instead of defining a custom macro in
pci-xgene.c (Pali Rohár)
* remotes/lorenzo/pci/xgene:
PCI: xgene: Use PCI_VENDOR_ID_AMCC macro
- Assign a number to each VMD controller to distinguish them in
/proc/interrupts (Chunguang Xu)
- Don't disable VMD MSI-X remapping if IOMMU remapping is enabled (Adrian
Huang)
- Add Kconfig dependency on !UML for allyesconfig build issue (Johannes
Berg)
* remotes/lorenzo/pci/vmd:
PCI: vmd: depend on !UML
PCI: vmd: Do not disable MSI-X remapping if interrupt remapping is enabled by IOMMU
PCI: vmd: Assign a number to each VMD controller
- Reorganize to separate out PHY logic (Mauro Carvalho Chehab)
- Add support for external PHY in addition to the internal PHY (Mauro
Carvalho Chehab)
- Use regmap so both kirin driver and PHY can access APB registers (Mauro
Carvalho Chehab)
- Add support for per-lane PERST# GPIOs on HiKey970 external PEX 8606 PCI
bridge (Mauro Carvalho Chehab)
- Add "hisilicon,kirin970-pcie" compatible string (Mauro Carvalho Chehab)
- Add MODULE_* macros (Mauro Carvalho Chehab)
- Allow building as a module (Mauro Carvalho Chehab)
- Add power_off support for Kirin 960 PHY (Mauro Carvalho Chehab)
- Disable clkreq during poweroff sequence (Mauro Carvalho Chehab)
- De-init the dwc driver during remove (Mauro Carvalho Chehab)
- Allow removal of kirin driver (Mauro Carvalho Chehab)
* pci/host/kirin:
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: kirin: Use regmap for APB registers
PCI: kirin: Add support for a PHY layer
PCI: kirin: Reorganize the PHY logic inside the driver
- Export dw_pcie_ep_reset_bar(), dw_pcie_link_up() so more drivers can be
modular (Luca Ceresoli)
- Allow dra7xx host and endpoint drivers to be modules (Luca Ceresoli)
- Enable dra7xx optional external clock if present (Luca Ceresoli)
- Clean up Kconfig dependencies for PCIE_DW_HOST- and PCIE_DW_EP-based
drivers (Andy Shevchenko)
- Remove visconti redundant dev_err() after platform_get_irq_byname()
failure (Krzysztof Wilczyński)
- Run dwc .host_init() method before registering MSI interrupt handler so
we have a chance to deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Serialize uniphier INTx masking/unmasking (Kunihiko Hayashi)
* pci/host/dwc:
PCI: uniphier: Serialize INTx masking/unmasking and fix the bit operation
PCI: dwc: Perform host_init() before registering msi
PCI: visconti: Remove surplus dev_err() when using platform_get_irq_byname()
PCI: dwc: Clean up Kconfig dependencies (PCIE_DW_EP)
PCI: dwc: Clean up Kconfig dependencies (PCIE_DW_HOST)
PCI: dra7xx: Get an optional clock
PCI: dra7xx: Remove unused include
PCI: dra7xx: Make it a kernel module
PCI: dwc: Export more symbols to allow modular drivers
- Make of_phandle_args_to_fwspec() generally available (Marc Zyngier)
- Allow matching of interrupt-maps local to interrupt controller or PCI
device (Marc Zyngier)
- Add Apple SoC (e.g., M1) PCIe host controller driver, which enables
access to USB type-A, Ethernet, Wi-Fi, Bluetooth devices; these require
additional drivers of their own (Alyssa Rosenzweig)
- Add apple INTx, per-port, and MSI interrupt support (Marc Zyngier)
- Configure apple Requester-ID-to-Stream-ID mapper for IOMMU (DART) support
(Marc Zyngier)
* pci/host/apple:
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits (Marek
Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits at
startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge" instead of
the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement this per
spec (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge
PCI: aardvark: Fix support for PCI_BRIDGE_CTL_BUS_RESET on emulated bridge
PCI: aardvark: Set PCI Bridge Class Code to PCI Bridge
PCI: aardvark: Fix support for bus mastering and PCI_COMMAND on emulated bridge
PCI: aardvark: Read all 16-bits from PCIE_MSI_PAYLOAD_REG
PCI: aardvark: Fix return value of MSI domain .alloc() method
PCI: pci-bridge-emul: Fix emulation of W1C bits
PCI: aardvark: Fix reporting Data Link Layer Link Active
PCI: aardvark: Fix checking for link up via LTSSM state
PCI: aardvark: Fix link training
PCI: aardvark: Simplify initialization of rootcap on virtual bridge
PCI: aardvark: Implement re-issuing config requests on CRS response
PCI: aardvark: Deduplicate code in advk_pcie_rd_conf()
PCI: aardvark: Do not unmask unused interrupts
PCI: aardvark: Do not clear status bits of masked interrupts
PCI: aardvark: Fix configuring Reference clock
PCI: aardvark: Fix preserving PCI_EXP_RTCTL_CRSSVE flag on emulated bridge
PCI: aardvark: Don't spam about PIO Response Status
PCI: aardvark: Fix PCIe Max Payload Size setting
PCI: Add PCI_EXP_DEVCTL_PAYLOAD_* macros
The Apple PCIe controller doesn't directly feed the endpoint's Requester ID
to the IOMMU (DART), but instead maps RIDs onto Stream IDs (SIDs). The DART
and the PCIe controller must thus agree on the SIDs that are used for
translation (by using the 'iommu-map' property).
For this purpose, parse the 'iommu-map' property each time a device gets
added, and use the resulting translation to configure the PCIe RID-to-SID
mapper. Similarly, remove the translation if/when the device gets removed.
This is all driven from a bus notifier which gets registered at probe time.
Hopefully this is the only PCI controller driver in the whole system.
[bhelgaas: squash indentation from Zhaoyu Liu <zackary.liu.pro@gmail.com>:
https://lore.kernel.org/r/20211031135544.GA1616@pc]
Link: https://lore.kernel.org/r/20210929163847.2807812-10-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
The MSI doorbell on Apple HW can be any address in the low 4GB range.
However, the MSI write is matched by the PCIe block before hitting the
iommu. It must thus be excluded from the IOVA range that is assigned to any
PCIe device.
Link: https://lore.kernel.org/r/20210929163847.2807812-9-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Probe for the 'msi-ranges' property, and implement the MSI support in the
form of the usual two-level hierarchy.
Note that contrary to the wired interrupts, MSIs are shared among all the
ports.
Link: https://lore.kernel.org/r/20210929163847.2807812-8-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for the per-port interrupt controller that deals with both INTx
signalling and management interrupts.
This allows the Link-up/Link-down interrupts to be wired, allowing the
bring-up to be synchronised (and provide debug information). The framework
can further be used to handle the rest of the per port events if and when
necessary.
Likewise, INTx signalling is implemented so that end-points can actually be
used.
Link: https://lore.kernel.org/r/20210929163847.2807812-7-maz@kernel.org
Link: https://lore.kernel.org/r/20211004150552.3844830-1-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that everything is in place at the poweroff sequence, this driver can
use module_platform_driver(), which allows it to be removed.
Link: https://lore.kernel.org/r/53b40494252444a9b830827922c4e3a301b8f863.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The logic under .remove ops is missing a call to dw_pcie_host_deinit(). Add
it, in order to allow the DWC core to be properly cleaned up.
Link: https://lore.kernel.org/r/838621e1c84ebaac153ccd9c36ea5e1254c61ead.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The logic at kirin_pcie_gpio_request() enables some clkreq GPIO lines.
Disable them during power-off.
Link: https://lore.kernel.org/r/f403e590843de1a581cade2d534d34715706f54e.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
Instead of having two copies of the same logic, place the power-off logic
in a separate function.
No functional changes.
Link: https://lore.kernel.org/r/64f6e8da3e5fff38b6c8fcb208ace46efe6555bb.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
There's nothing preventing this driver from being loaded as a module.
Change its config from bool to tristate.
Link: https://lore.kernel.org/r/b5e7cfe9df09b492750bd6db0f0c911eaae8c2d4.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
Apple's PCIe controller requires clocks to be configured in order to
bring up the hardware. Add the register pokes required to do so.
Adapted from Corellium's driver via Mark Kettenis's U-Boot patches.
Co-developed-by: Stan Skowronek <stan@corellium.com>
Link: https://lore.kernel.org/r/20210929163847.2807812-6-maz@kernel.org
Signed-off-by: Stan Skowronek <stan@corellium.com>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a minimal driver to bring up the PCIe bus on Apple system-on-chips,
particularly the Apple M1. This driver exposes the internal bus used for
the USB type-A ports, Ethernet, Wi-Fi, and Bluetooth. Bringing up the
radios requires additional drivers beyond what's necessary for PCIe itself.
Co-developed-by: Stan Skowronek <stan@corellium.com>
Link: https://lore.kernel.org/r/20210929163847.2807812-5-maz@kernel.org
Signed-off-by: Stan Skowronek <stan@corellium.com>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
We already include <linux/device.h> and <linux/msi.h>, which
include <asm/device.h> and <asm/msi.h>.
Drop the redundant includes of <asm/device.h> and <asm/msi.h>.
[bhelgaas: squash in fix from Wan Jiabing <wanjiabing@vivo.com>:
https://lore.kernel.org/r/20211104063720.29375-1-wanjiabing@vivo.com]
Link: https://lore.kernel.org/r/20211013003145.1107148-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Derrick <jonathan.derrick@linux.dev>
If an error occurs after a successful cdns_pcie_init_phy() call, it must be
undone by a cdns_pcie_disable_phy() call, as already done above and below.
Update the goto to branch at the correct place of the error handling path.
Link: https://lore.kernel.org/r/db477b0cb444891a17c4bb424467667dc30d0bab.1624794264.git.christophe.jaillet@wanadoo.fr
Fixes: 49e0efdce7 ("PCI: j721e: Add support to provide refclk to PCIe connector")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
The PHY layer need to access APB registers too, for Kirin 970. So place
them into a named regmap.
Link: https://lore.kernel.org/r/daf0e4bda5a69a5ac8484e70f09351a959805c8c.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The pcie-kirin driver contains both PHY and generic PCI driver.
The best would be, instead, to support a PCI PHY driver, making the driver
more generic.
However, it is too late to remove the Kirin 960 PHY, as a change like that
would make the DT schema incompatible with past versions.
So, add support for an external PHY driver without removing the existing
Kirin 960 PHY from it.
Link: https://lore.kernel.org/r/f38361df2e9d0dc5a38ff942b631f7fef64cdc12.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The pcie-kirin PCIe driver contains internally a PHY interface for
Kirin 960.
As the next patches will add support for using an external PHY driver,
reorganize the driver in a way that the PHY part will be self-contained.
This could be moved to a separate PHY driver, but a change like that would
mean a non-backward-compatible DT schema change.
Link: https://lore.kernel.org/r/ad2f4aa6bbb71d5c9af0139704672f75f12644fc.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Aardvark supports PCIe Hot Reset via PCIE_CORE_CTRL1_REG.
Use it for implementing PCI_BRIDGE_CTL_BUS_RESET bit of PCI_BRIDGE_CONTROL
register on emulated bridge.
With this, the function pci_reset_secondary_bus() starts working and can
reset connected PCIe card. Custom userspace script [1] which uses setpci
can trigger PCIe Hot Reset and reset the card manually.
[1] https://alexforencich.com/wiki/en/pcie/hot-reset-linux
Link: https://lore.kernel.org/r/20211028185659.20329-7-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Aardvark controller has something like config space of a Root Port
available at offset 0x0 of internal registers - these registers are used
for implementation of the emulated bridge.
The default value of Class Code of this bridge corresponds to a RAID Mass
storage controller, though. (This is probably intended for when the
controller is used as Endpoint.)
Change the Class Code to correspond to a PCI Bridge.
Add comment explaining this change.
Link: https://lore.kernel.org/r/20211028185659.20329-6-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
From very vague, ambiguous and incomplete information from Marvell we
deduced that the 32-bit Aardvark register at address 0x4
(PCIE_CORE_CMD_STATUS_REG), which is not documented for Root Complex mode
in the Functional Specification (only for Endpoint mode), controls two
16-bit PCIe registers: Command Register and Status Registers of PCIe Root
Port.
This means that bit 2 controls bus mastering and forwarding of memory and
I/O requests in the upstream direction. According to PCI specifications
bits [0:2] of Command Register, this should be by default disabled on
reset. So explicitly disable these bits at early setup of the Aardvark
driver.
Remove code which unconditionally enables all 3 bits and let kernel code
(via pci_set_master() function) to handle bus mastering of Root PCIe
Bridge via emulated PCI_COMMAND on emulated bridge.
Link: https://lore.kernel.org/r/20211028185659.20329-5-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # b2a56469d5 ("PCI: aardvark: Add FIXME comment for PCIE_CORE_CMD_STATUS_REG access")
The PCIE_MSI_PAYLOAD_REG contains 16-bit MSI number, not only lower
8 bits. Fix reading content of this register and add a comment
describing the access to this register.
Link: https://lore.kernel.org/r/20211028185659.20329-4-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
MSI domain callback .alloc() (implemented by advk_msi_irq_domain_alloc()
function) should return zero on success, since non-zero value indicates
failure.
When the driver was converted to generic MSI API in commit f21a8b1b68
("PCI: aardvark: Move to MSI handling using generic MSI support"), it
was converted so that it returns hwirq number.
Fix this.
Link: https://lore.kernel.org/r/20211028185659.20329-3-kabel@kernel.org
Fixes: f21a8b1b68 ("PCI: aardvark: Move to MSI handling using generic MSI support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
The bare "unsigned" type implicitly means "unsigned int", but the preferred
coding style is to use the complete type name.
Update the bare use of "unsigned" to the preferred "unsigned int".
No change to functionality intended.
See a1ce18e4f9 ("checkpatch: warn on bare unsigned or signed declarations
without int").
Link: https://lore.kernel.org/r/20211013014136.1117543-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add driver for the PCIe controller of the MT7621 SoC.
[bhelgaas: rename from pci-mt7621.c to pcie-mt7621.c; also rename Kconfig
symbol from PCI_MT7621 to PCIE_MT7621]
Link: https://lore.kernel.org/r/20210922050035.18162-3-sergio.paracuellos@gmail.com
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The condition register PCI_RCV_INTX is used in irq_mask() and irq_unmask()
callbacks. Accesses to register can occur at the same time without a lock.
Add a lock into each callback to prevent the issue.
And INTX mask and unmask fields in PCL_RCV_INTX register should only be
set/reset for each bit. Clearing by PCL_RCV_INTX_ALL_MASK should be
removed.
INTX status fields in PCL_RCV_INTX register only indicates each INTX
interrupt status, so the handler can't clear by writing 1 to the field.
The status is expected to be cleared by the interrupt origin.
The ack function has no meaning, so should remove it.
Suggested-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/1631924579-24567-1-git-send-email-hayashi.kunihiko@socionext.com
Fixes: 7e6d5cd88a ("PCI: uniphier: Add UniPhier PCIe host controller support")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
On the SC7280, the clock source for gcc_pcie_1_pipe_clk_src must be the
TCXO while gdsc is enabled. After PHY init successful clock source should
switch to pipe clock for gcc_pcie_1_pipe_clk_src.
Link: https://lore.kernel.org/r/1633628923-25047-6-git-send-email-pmaliset@codeaurora.org
Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Add struct qcom_pcie_cfg as match data for all platforms. Assign
appropriate platform ops into struct qcom_pcie_cfg and read using
of_device_get_match_data() in qcom_pcie_probe().
Link: https://lore.kernel.org/r/1633628923-25047-5-git-send-email-pmaliset@codeaurora.org
Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
With UML having enabled (simulated) PCI on UML, VMD breaks
allyesconfig/allmodconfig compilation because it assumes
it's running on X86_64 bare metal, and has hardcoded API
use of ARCH=x86. Make it depend on !UML to fix this.
Link: https://lore.kernel.org/r/20210811162530.affe26231bc3.I131b3c1e67e3d2ead6e98addd256c835fbef9a3e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
"dom_req" is a u16 but varargs automatically promotes it to int, so there's
no point in using the %h modifier. Drop it.
See cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]") and 70eb2275ff ("checkpatch: add
warning for unnecessary use of %h[xudi] and %hh[xudi]").
Link: https://lore.kernel.org/r/20211008222732.2868493-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When enabling VMD in BIOS setup (Ice Lake Processor: Whitley platform),
the host OS cannot boot successfully with the following error message:
nvme nvme0: I/O 12 QID 0 timeout, completion polled
nvme nvme0: Shutdown timeout set to 6 seconds
DMAR: DRHD: handling fault status reg 2
DMAR: [INTR-REMAP] Request device [0x00:0x00.5] fault index 0xa00 [fault reason 0x25] Blocked a compatibility format interrupt request
The request device is the VMD controller:
# lspci -s 0000:00.5 -nn
0000:00:00.5 RAID bus controller [0104]: Intel Corporation Volume
Management Device NVMe RAID Controller [8086:28c0] (rev 04)
`git bisect` points to this offending commit ee81ee84f8 ("PCI:
vmd: Disable MSI-X remapping when possible"), which disables VMD MSI
remapping. The IOMMU hardware blocks the compatibility format
interrupt request because Interrupt Remapping Enable Status (IRES) and
Extended Interrupt Mode Enable (EIME) are enabled. Please refer to
section "5.1.4 Interrupt-Remapping Hardware Operation" in Intel VT-d
spec.
To fix the issue, VMD driver still enables the interrupt remapping
irrespective of VMD_FEAT_CAN_BYPASS_MSI_REMAP if the IOMMU subsystem
enables the interrupt remapping.
Test configuration is shown as follows:
* Two VMD controllers
1. 8086:28c0 (Whitley's VMD)
2. 8086:201d (Purley's VMD: The issue does not appear in this
controller. Just make sure if any side effect occurs.)
* w/wo intremap=off
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=214219
Link: https://lore.kernel.org/r/20210901124047.1615-1-adrianhuang0701@gmail.com
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Cc: Jon Derrick <jonathan.derrick@intel.com>
Cc: Nirmal Patel <nirmal.patel@linux.intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
On the Qualcomm sc8180x platform the bootloader does something related
to PCI that leaves a pending "msi" interrupt, which with the current
ordering often fires before init has a chance to enable the clocks that
are necessary for the interrupt handler to access the hardware.
Move the host_init() call before the registration of the "msi" interrupt
handler to ensure the host driver has a chance to enable the clocks.
The assignment of the bridge's ops and child_ops is moved along, because
at least the TI Keystone driver overwrites these in its host_init
callback.
Link: https://lore.kernel.org/r/20210823154958.305677-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add driver for Qualcomm PCIe Endpoint controller based on the DesignWare
core with added Qualcomm-specific wrapper around the core. The driver
support is very basic such that it supports only enumeration, PCIe
read/write, and MSI. There is no ASPM and PM support for now but these will
be added later.
The driver is capable of using the PERST# and WAKE# side-band GPIOs for
operation and written on top of the DWC PCI framework.
[bhelgaas: wrap a few long lines]
Co-developed-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: restructured the driver and fixed several bugs for upstream]
Link: https://lore.kernel.org/r/20210920065946.15090-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Correct a number of misspelled words and remove any words that were
duplicated in the PCI tree. No change to functionality intended.
Link: https://lore.kernel.org/r/20211006233827.147328-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove includes that are not needed, to speed up (re)compilation.
Most of these are relics from splitting the driver in a host and a
common part.
[bhelgaas: use driver tag analogous to rcar-ep]
Link: https://lore.kernel.org/r/54bed9a0e6991490ddb2b07e5abfaf40a7a62928.1633090577.git.geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Remove includes that are not needed, to speed up (re)compilation. Include
<linux/pm_runtime.h>, which is needed, and was included implicitly through
<linux/phy/phy.h> before.
Most of these are relics from splitting the driver in a host and a common
part and adding endpoint support.
[bhelgaas: use driver tag consistent with cadence-ep, designware-ep]
Link: https://lore.kernel.org/r/7c708841a2bf84f85b14a963271c3e99c8ba38a5.1633090444.git.geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAmFeykwTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXhRLCADXOOSGKk4L1vWssRRhLmMXI45ElocY
EbZ/mXcQhxKnlVhdMNnupGjz+lU5FQGkCCWlhmt9Ml2O6R+lDx+zIUS8BK3Nkom9
twWjueMtum6yFwDMGYALhptVLjDqVFG71QcW0incghpnAx4s2FVE8h38md5MuUFY
Kqqf/dRkppSePldHFrRG/e4c6r0WyTsJ6Z9LTU0UYp5GqJcmUJlx7TxxqzGk5Fti
GpQ5cFS7JX8xHAkRROk/dvwJte1RRnBAW6lIWxwAaDJ6Gbg7mNfOQe7n+/KRO7ZG
gC5hbkP9tMv2nthLxaFbpu791U4lMZ2WiTLZvbgCseO3FCmToXWZ6TDd
=1mdq
-----END PGP SIGNATURE-----
Merge tag 'hyperv-fixes-signed-20211007' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- Replace uuid.h with types.h in a header (Andy Shevchenko)
- Avoid sleeping in atomic context in PCI driver (Long Li)
- Avoid sending IPI to self when it shouldn't (Vitaly Kuznetsov)
* tag 'hyperv-fixes-signed-20211007' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/hyperv: Avoid erroneously sending IPI to 'self'
hyper-v: Replace uuid.h with types.h
PCI: hv: Fix sleep while in non-sleep context when removing child devices from the bus
If the system has multiple VMD controllers, the driver does not assign
a number to each controller, so when analyzing the interrupt through
/proc/interrupts, the names of all controllers are the same, which is
not very convenient for problem analysis. Here, try to assign a number
to each VMD controller.
Link: https://lore.kernel.org/r/1631884404-24141-1-git-send-email-brookxu.cn@gmail.com
Signed-off-by: Chunguang Xu <brookxu@tencent.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
The "depends on" Kconfig construct is a no-op in options that
are selected and therefore has no effect. Remove it.
Clean up the users of PCIE_DW_EP and introduce idiom
depends on PCI_ENDPOINT
select PCIE_DW_EP
for all of them.
Link: https://lore.kernel.org/r/20210623140103.47818-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The "depends on" Kconfig construct is a no-op in options that
are selected and therefore has no effect. Remove it.
Furthermore, there is no need to repeat menu dependencies (PCI).
Clean up the users of PCIE_DW_HOST and introduce idiom
depends on PCI_MSI_IRQ_DOMAIN
select PCIE_DW_HOST
for all of them.
Link: https://lore.kernel.org/r/20210623140103.47818-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add support for reporting PCI_EXP_LNKSTA_DLLLA bit in Link Control register
on emulated bridge via current LTSSM state. Also correctly indicate DLLLA
capability via PCI_EXP_LNKCAP_DLLLARC bit in Link Control Capability
register.
Link: https://lore.kernel.org/r/20211005180952.6812-14-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Current implementation of advk_pcie_link_up() is wrong as it marks also
link disabled or hot reset states as link up.
Fix it by marking link up only to those states which are defined in PCIe
Base specification 3.0, Table 4-14: Link Status Mapped to the LTSSM.
To simplify implementation, Define macros for every LTSSM state which
aardvark hardware can return in CFG_REG register.
Fix also checking for link training according to the same Table 4-14.
Define a new function advk_pcie_link_training() for this purpose.
Link: https://lore.kernel.org/r/20211005180952.6812-13-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Cc: Remi Pommarel <repk@triplefau.lt>
Fix multiple link training issues in aardvark driver. The main reason of
these issues was misunderstanding of what certain registers do, since their
names and comments were misleading: before commit 96be36dbff ("PCI:
aardvark: Replace custom macros by standard linux/pci_regs.h macros"), the
pci-aardvark.c driver used custom macros for accessing standard PCIe Root
Bridge registers, and misleading comments did not help to understand what
the code was really doing.
After doing more tests and experiments I've come to the conclusion that the
SPEED_GEN register in aardvark sets the PCIe revision / generation
compliance and forces maximal link speed. Both GEN3 and GEN2 values set the
read-only PCI_EXP_FLAGS_VERS bits (PCIe capabilities version of Root
Bridge) to value 2, while GEN1 value sets PCI_EXP_FLAGS_VERS to 1, which
matches with PCI Express specifications revisions 3, 2 and 1 respectively.
Changing SPEED_GEN also sets the read-only bits PCI_EXP_LNKCAP_SLS and
PCI_EXP_LNKCAP2_SLS to corresponding speed.
(Note that PCI Express rev 1 specification does not define PCI_EXP_LNKCAP2
and PCI_EXP_LNKCTL2 registers and when SPEED_GEN is set to GEN1 (which
also sets PCI_EXP_FLAGS_VERS set to 1), lspci cannot access
PCI_EXP_LNKCAP2 and PCI_EXP_LNKCTL2 registers.)
Changing PCIe link speed can be done via PCI_EXP_LNKCTL2_TLS bits of
PCI_EXP_LNKCTL2 register. Armada 3700 Functional Specifications says that
the default value of PCI_EXP_LNKCTL2_TLS is based on SPEED_GEN value, but
tests showed that the default value is always 8.0 GT/s, independently of
speed set by SPEED_GEN. So after setting SPEED_GEN, we must also set value
in PCI_EXP_LNKCTL2 register via PCI_EXP_LNKCTL2_TLS bits.
Triggering PCI_EXP_LNKCTL_RL bit immediately after setting LINK_TRAINING_EN
bit actually doesn't do anything. Tests have shown that a delay is needed
after enabling LINK_TRAINING_EN bit. As triggering PCI_EXP_LNKCTL_RL
currently does nothing, remove it.
Commit 43fc679ced ("PCI: aardvark: Improve link training") introduced
code which sets SPEED_GEN register based on negotiated link speed from
PCI_EXP_LNKSTA_CLS bits of PCI_EXP_LNKSTA register. This code was added to
fix detection of Compex WLE900VX (Atheros QCA9880) WiFi GEN1 PCIe cards, as
otherwise these cards were "invisible" on PCIe bus (probably because they
crashed). But apparently more people reported the same issues with these
cards also with other PCIe controllers [1] and I was able to reproduce this
issue also with other "noname" WiFi cards based on Atheros QCA9890 chip
(with the same PCI vendor/device ids as Atheros QCA9880). So this is not an
issue in aardvark but rather an issue in Atheros QCA98xx chips. Also, this
issue only exists if the kernel is compiled with PCIe ASPM support, and a
generic workaround for this is to change PCIe Bridge to 2.5 GT/s link speed
via PCI_EXP_LNKCTL2_TLS_2_5GT bits in PCI_EXP_LNKCTL2 register [2], before
triggering PCI_EXP_LNKCTL_RL bit. This workaround also works when SPEED_GEN
is set to value GEN2 (5 GT/s). So remove this hack completely in the
aardvark driver and always set SPEED_GEN to value from 'max-link-speed' DT
property. Fix for Atheros QCA98xx chips is handled separately by patch [2].
These two things (code for triggering PCI_EXP_LNKCTL_RL bit and changing
SPEED_GEN value) also explain why commit 6964494582 ("PCI: aardvark:
Train link immediately after enabling training") somehow fixed detection of
those problematic Compex cards with Atheros chips: if triggering link
retraining (via PCI_EXP_LNKCTL_RL bit) was done immediately after enabling
link training (via LINK_TRAINING_EN), it did nothing. If there was a
specific delay, aardvark HW already initialized PCIe link and therefore
triggering link retraining caused the above issue. Compex cards triggered
link down event and disappeared from the PCIe bus.
Commit f4c7d053d7 ("PCI: aardvark: Wait for endpoint to be ready before
training link") added 100ms sleep before calling 'Start link training'
command and explained that it is a requirement of PCI Express
specification. But the code after this 100ms sleep was not doing 'Start
link training', rather it triggered PCI_EXP_LNKCTL_RL bit via PCIe Root
Bridge to put link into Recovery state.
The required delay after fundamental reset is already done in function
advk_pcie_wait_for_link() which also checks whether PCIe link is up.
So after removing the code which triggers PCI_EXP_LNKCTL_RL bit on PCIe
Root Bridge, there is no need to wait 100ms again. Remove the extra
msleep() call and update comment about the delay required by the PCI
Express specification.
According to Marvell Armada 3700 Functional Specifications, Link training
should be enabled via aardvark register LINK_TRAINING_EN after selecting
PCIe generation and x1 lane. There is no need to disable it prior resetting
card via PERST# signal. This disabling code was introduced in commit
5169a9851d ("PCI: aardvark: Issue PERST via GPIO") as a workaround for
some Atheros cards. It turns out that this also is Atheros specific issue
and affects any PCIe controller, not only aardvark. Moreover this Atheros
issue was triggered by juggling with PCI_EXP_LNKCTL_RL, LINK_TRAINING_EN
and SPEED_GEN bits interleaved with sleeps. Now, after removing triggering
PCI_EXP_LNKCTL_RL, there is no need to explicitly disable LINK_TRAINING_EN
bit. So remove this code too. The problematic Compex cards described in
previous git commits are correctly detected in advk_pcie_train_link()
function even after applying all these changes.
Note that with this patch, and also prior this patch, some NVMe disks which
support PCIe GEN3 with 8 GT/s speed are negotiated only at the lowest link
speed 2.5 GT/s, independently of SPEED_GEN value. After manually triggering
PCI_EXP_LNKCTL_RL bit (e.g. from userspace via setpci), these NVMe disks
change link speed to 5 GT/s when SPEED_GEN was configured to GEN2. This
issue first needs to be properly investigated. I will send a fix in the
future.
On the other hand, some other GEN2 PCIe cards with 5 GT/s speed are
autonomously by HW autonegotiated at full 5 GT/s speed without need of any
software interaction.
Armada 3700 Functional Specifications describes the following steps for
link training: set SPEED_GEN to GEN2, enable LINK_TRAINING_EN, poll until
link training is complete, trigger PCI_EXP_LNKCTL_RL, poll until signal
rate is 5 GT/s, poll until link training is complete, enable ASPM L0s.
The requirement for triggering PCI_EXP_LNKCTL_RL can be explained by the
need to achieve 5 GT/s speed (as changing link speed is done by throw to
recovery state entered by PCI_EXP_LNKCTL_RL) or maybe as a part of enabling
ASPM L0s (but in this case ASPM L0s should have been enabled prior
PCI_EXP_LNKCTL_RL).
It is unknown why the original pci-aardvark.c driver was triggering
PCI_EXP_LNKCTL_RL bit before waiting for the link to be up. This does not
align with neither PCIe base specifications nor with Armada 3700 Functional
Specification. (Note that in older versions of aardvark, this bit was
called incorrectly PCIE_CORE_LINK_TRAINING, so this may be the reason.)
It is also unknown why Armada 3700 Functional Specification says that it is
needed to trigger PCI_EXP_LNKCTL_RL for GEN2 mode, as according to PCIe
base specification 5 GT/s speed negotiation is supposed to be entirely
autonomous, even if initial speed is 2.5 GT/s.
[1] - https://lore.kernel.org/linux-pci/87h7l8axqp.fsf@toke.dk/
[2] - https://lore.kernel.org/linux-pci/20210326124326.21163-1-pali@kernel.org/
Link: https://lore.kernel.org/r/20211005180952.6812-12-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
PCIe config space can be initialized also before pci_bridge_emul_init()
call, so move rootcap initialization after PCI config space initialization.
This simplifies the function a little since it removes one if (ret < 0)
check.
Link: https://lore.kernel.org/r/20211005180952.6812-11-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Commit 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value") fixed
handling of CRS response and when CRSSVE flag was not enabled it marked CRS
response as failed transaction (due to simplicity).
But pci-aardvark.c driver is already waiting up to the PIO_RETRY_CNT count
for PIO config response and so we can with a small change implement
re-issuing of config requests as described in PCIe base specification.
This change implements re-issuing of config requests when response is CRS.
Set upper bound of wait cycles to around PIO_RETRY_CNT, afterwards the
transaction is marked as failed and an all-ones value is returned as
before.
We do this by returning appropriate error codes from function
advk_pcie_check_pio_status(). On CRS we return -EAGAIN and caller then
reissues transaction.
Link: https://lore.kernel.org/r/20211005180952.6812-10-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Avoid code repetition in advk_pcie_rd_conf() by handling errors with
goto jump, as is customary in kernel.
Link: https://lore.kernel.org/r/20211005180952.6812-9-kabel@kernel.org
Fixes: 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
There are lot of undocumented interrupt bits. To prevent unwanted
spurious interrupts, fix all *_ALL_MASK macros to define all interrupt
bits, so that driver can properly mask all interrupts, including those
which are undocumented.
Link: https://lore.kernel.org/r/20211005180952.6812-8-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
The PCIE_ISR1_REG says which interrupts are currently set / active,
including those which are masked.
The driver currently reads this register and looks if some unmasked
interrupts are active, and if not, it clears status bits of _all_
interrupts, including the masked ones.
This is incorrect, since, for example, some drivers may poll these bits.
Remove this clearing, and also remove this early return statement
completely, since it does not change functionality in any way.
Link: https://lore.kernel.org/r/20211005180952.6812-7-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Commit 366697018c ("PCI: aardvark: Add PHY support") introduced
configuration of PCIe Reference clock via PCIE_CORE_REF_CLK_REG register,
but did it incorrectly.
PCIe Reference clock differential pair is routed from system board to
endpoint card, so on CPU side it has output direction. Therefore it is
required to enable transmitting and disable receiving.
Default configuration according to Armada 3700 Functional Specifications is
enabled receiver part and disabled transmitter.
We need this change because otherwise PCIe Reference clock is configured to
some undefined state when differential pair is used for both transmitting
and receiving.
Fix this by disabling receiver part.
Link: https://lore.kernel.org/r/20211005180952.6812-6-kabel@kernel.org
Fixes: 366697018c ("PCI: aardvark: Add PHY support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Commit 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value") started
using CRSSVE flag for handling CRS responses.
PCI_EXP_RTCTL_CRSSVE flag is stored only in emulated config space buffer
and there is handler for PCI_EXP_RTCTL register. So every read operation
from config space automatically clears CRSSVE flag as it is not defined in
PCI_EXP_RTCTL read handler.
Fix this by reading current CRSSVE bit flag from emulated space buffer and
appending it to PCI_EXP_RTCTL read response.
Link: https://lore.kernel.org/r/20211005180952.6812-5-kabel@kernel.org
Fixes: 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Use dev_dbg() instead of dev_err() in advk_pcie_check_pio_status().
For example CRS is not an error status, it just says that the request
should be retried.
Link: https://lore.kernel.org/r/20211005180952.6812-4-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Change PCIe Max Payload Size setting in PCIe Device Control register to 512
bytes to align with PCIe Link Initialization sequence as defined in Marvell
Armada 3700 Functional Specification. According to the specification,
maximal Max Payload Size supported by this device is 512 bytes.
Without this kernel prints suspicious line:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 16384, max 512)
With this change it changes to:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 512, max 512)
Link: https://lore.kernel.org/r/20211005180952.6812-3-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Previously, the maximum link speed was set following an "fsl,max-link-speed"
property read, and should the read failed, then the PCIe generation was
manually set to PCIe Gen1 and thus limiting the link speed to 2.5 GT/s.
Code refactoring completed in the commit 39bc500650 ("PCI: dwc:
Centralize link gen setting") changed to the logic that was previously
used to limit the maximum link speed leaving behind an unused assignment
to a variable "ret".
Since the value returned from the of_property_read_u32() and stored in
the variable "ret" is never used in any meaningful way, and it's also
immediately reassigned in the code that follows, the assignment can be
removed.
Link: https://lore.kernel.org/r/20211003025439.84783-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Header file linux/pci_ids.h defines AMCC vendor id (0x10e8) macro named
PCI_VENDOR_ID_AMCC. So use this macro instead of driver custom macro.
Link: https://lore.kernel.org/r/20210927134356.11799-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
If the clock is provided externally we need to make sure it is enabled
before starting PCI scan.
Link: https://lore.kernel.org/r/20210531085934.2662457-5-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Unused since commit e259c2926c ("PCI: pci-dra7xx: Prepare for deferred
probe with module_platform_driver").
Link: https://lore.kernel.org/r/20210531085934.2662457-4-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Enable building the driver as a loadable kernel module.
Link: https://lore.kernel.org/r/20210531085934.2662457-3-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
These symbols are used by the pci-dra7xx driver. Export them to allow
building pci-dra7xx as a module.
Link: https://lore.kernel.org/r/20210531085934.2662457-2-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
In hv_pci_bus_exit, the code is holding a spinlock while calling
pci_destroy_slot(), which takes a mutex.
This is not safe for spinlock. Fix this by moving the children to be
deleted to a list on the stack, and removing them after spinlock is
released.
Fixes: 94d2276320 ("PCI: hv: Fix a race condition when removing the device")
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: "Krzysztof Wilczyński" <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/linux-hyperv/20210823152130.GA21501@kili/
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/1630365207-20616-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
- Add ACPI support to the PCI VMD driver (Rafael Wysocki).
- Rearrange suspend-to-idle support code to reflect the platform
firmware expectations on some AMD platforms (Mario Limonciello).
- Make SSDT overlays documentation follow the code documented by it
more closely (Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----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=8lPe
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These add ACPI support to the PCI VMD driver, improve suspend-to-idle
support for AMD platforms and update documentation.
Specifics:
- Add ACPI support to the PCI VMD driver (Rafael Wysocki)
- Rearrange suspend-to-idle support code to reflect the platform
firmware expectations on some AMD platforms (Mario Limonciello)
- Make SSDT overlays documentation follow the code documented by it
more closely (Andy Shevchenko)"
* tag 'acpi-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PM: s2idle: Run both AMD and Microsoft methods if both are supported
Documentation: ACPI: Align the SSDT overlays file with the code
PCI: VMD: ACPI: Make ACPI companion lookup work for VMD bus
- Add max-virtual-functions to endpoint binding (Kishon Vijay Abraham I)
- Add pci_epf_add_vepf() API to add virtual function to endpoint (Kishon
Vijay Abraham I)
- Add pci_epf_vepf_link() to link virtual function to endpoint physical
function (Kishon Vijay Abraham I)
- Add virtual function number to pci_epc_ops endpoint ops interfaces
(Kishon Vijay Abraham I)
- Simplify register base address computation for endpoint BAR configuration
(Kishon Vijay Abraham I)
- Add support to configure virtual functions in cadence endpoint driver
(Kishon Vijay Abraham I)
- Add SR-IOV configuration to endpoint test driver (Kishon Vijay Abraham I)
- Document configfs usage to create virtual functions for endpoints (Kishon
Vijay Abraham I)
* remotes/lorenzo/pci/endpoint:
Documentation: PCI: endpoint/pci-endpoint-cfs: Guide to use SR-IOV
misc: pci_endpoint_test: Populate sriov_configure ops to configure SR-IOV device
PCI: cadence: Add support to configure virtual functions
PCI: cadence: Simplify code to get register base address for configuring BAR
PCI: endpoint: Add virtual function number in pci_epc ops
PCI: endpoint: Add support to link a physical function to a virtual function
PCI: endpoint: Add support to add virtual function in endpoint core
dt-bindings: PCI: pci-ep: Add binding to specify virtual function
- Fix runtime PM imbalance in rcar_pcie_ep_probe() (Dinghao Liu)
* remotes/lorenzo/pci/rcar:
PCI: rcar: Add L1 link state fix into data abort hook
PCI: rcar: Fix runtime PM imbalance in rcar_pcie_ep_probe()
- Split DT bindings for PCIe controllers with independent MSI domains into
separate nodes for MT2712/MT7622 (Chuanjia Liu)
- Locate shared registers from "mediatek,generic-pciecfg" property
(Chuanjia Liu)
- Get IRQ from "pcie_irq" if "interrupt-names" property is present to fix
an MSI issue (Chuanjia Liu)
- Get PCI domain from "linux,pci-domain" property if present (Chuanjia Liu)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Use PCI domain to handle ports detection
PCI: mediatek: Add new method to get irq number
PCI: mediatek: Add new method to get shared pcie-cfg base address
dt-bindings: PCI: mediatek: Update the Device tree bindings
- Add domain_nr in struct pci_host_bridge (Boqun Feng)
- Use host bridge MSI domain for root buses if present (Boqun Feng)
- Allow ARM64 virtual host bridge with no ACPI companion (e.g., Hyper-V)
(Boqun Feng)
- Make Hyper-V enumeration more generic (Arnd Bergmann)
- Set Hyper-V domain_nr at probe-time (Boqun Feng)
- Set up Hyper-V MSI domain at bridge probe-time (Boqun Feng)
- Enable Hyper-V bridge probing on ARM64 (Boqun Feng)
* remotes/lorenzo/pci/hyper-v:
PCI: hv: Turn on the host bridge probing on ARM64
PCI: hv: Set up MSI domain at bridge probing time
PCI: hv: Set ->domain_nr of pci_host_bridge at probing time
PCI: hv: Generify PCI probing
arm64: PCI: Support root bridge preparation for Hyper-V
arm64: PCI: Restructure pcibios_root_bridge_prepare()
PCI: Support populating MSI domains of root buses via bridges
PCI: Introduce domain_nr in pci_host_bridge
- Convert bool in structs to bitfield (Kishon Vijay Abraham I)
- Work around J7200 non-PCIe SERDES lane electrical issue that prevents
PCIe link training (Nadeem Athani)
- Add J7200 PCIe support to j721e (Kishon Vijay Abraham I)
- Add AM64 PCIe support to j721e (Kishon Vijay Abraham I)
- Add J7200 and AM64 device IDs to endpoint test (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/cadence:
misc: pci_endpoint_test: Add deviceID for AM64 and J7200
PCI: j721e: Add PCIe support for AM64
PCI: j721e: Add PCIe support for J7200
PCI: cadence: Add quirk flag to set minimum delay in LTSSM Detect.Quiet state
PCI: cadence: Use bitfield for *quirk_retrain_flag* instead of bool
- Fix PIO config access status checking (Evan Wang)
- Increase config access polling delay to 1.5s (Pali Rohár)
- Add PCIe Root Capabilities to bridge emulation (Pali Rohár)
- Report Config Request Retry Status when Software Visibility enabled (Pali
Rohár)
- Add back configuration of PCIe resources from 'ranges' DT property and
pay attention to DT size and CPU/PCI offset to fix issues with I/O port
space (Pali Rohár)
- Serialize masking and unmasking legacy INTx interrupts (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Fix masking and unmasking legacy INTx interrupts
PCI: aardvark: Configure PCIe resources from 'ranges' DT property
PCI: aardvark: Fix reporting CRS value
PCI: pci-bridge-emul: Add PCIe Root Capabilities Register
PCI: aardvark: Increase polling delay to 1.5s while waiting for PIO response
PCI: aardvark: Fix checking for PIO status
On some systems, in order to get to the deepest low-power state of
the platform (which may be necessary to save significant enough
amounts of energy while suspended to idle. for example), devices on
the PCI bus exposed by the VMD driver need to be power-managed via
ACPI. However, the layout of the ACPI namespace below the VMD
controller device object does not reflect the layout of the PCI bus
under the VMD host bridge, so in order to identify the ACPI companion
objects for the devices on that bus, it is necessary to use a special
_ADR encoding on the ACPI side. In other words, acpi_pci_find_companion()
does not work for these devices, so it needs to be amended with a
special lookup logic specific to the VMD bus.
Address this issue by allowing the VMD driver to temporarily install
an ACPI companion lookup hook containing the code matching the devices
on the VMD PCI bus with the corresponding objects in the ACPI
namespace.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Add a driver for the DesignWare-based PCIe controller found on
RK356X. The existing pcie-rockchip-host driver is only used for
the Rockchip-designed IP found on RK3399.
Link: https://lore.kernel.org/r/20210625065511.1096935-1-xxm@rock-chips.com
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Rob Herring <robh@kernel.org>
As part of code refactoring completed in a0fd361db8 ("PCI: dwc: Move
"dbi", "dbi2", and "addr_space" resource setup into common code"),
dw_plat_add_pcie_ep() was removed and the call to the dw_pcie_ep_init() was
moved into dw_plat_pcie_probe().
This left a break statement behind that is not needed any more as as
dw_plat_pcie_probe() returns immediately after calling dw_pcie_ep_init().
Remove this surplus break statement that became dead code.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210701210252.1638709-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The switch statement in the artpec6_pcie_probe() has a local code block
where "val" is defined and immediately used by the artpec6_pcie_readl().
This extra code block adds brackets at the same indentation level as the
switch statement itself which can hinder readability of the code.
Move the "val" declaration to the top of the function and remove
the extra code block from the switch statement.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210701204401.1636562-2-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
As part of code refactoring completed in a0fd361db8 ("PCI: dwc: Move
"dbi", "dbi2", and "addr_space" resource setup into common code"),
artpec6_add_pcie_ep() was removed and the call to the dw_pcie_ep_init()
was moved into artpec6_pcie_probe().
This left a break statement behind that is not needed any more as
artpec6_pcie_probe() returns immediately after calling dw_pcie_ep_init().
Remove this surplus break statement that became dead code.
Link: https://lore.kernel.org/r/20210701204401.1636562-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Add support for the PCIe RC controller on Toshiba Visconti ARM SoCs. This
PCIe controller is based on the Synopsys DesignWare PCIe core.
Link: https://lore.kernel.org/r/20210811083830.784065-3-nobuhiro1.iwamatsu@toshiba.co.jp
Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Use of_get_pci_domain_nr() to get the pci domain.
If the "linux,pci-domain" property is present, we assume that the PCIe
bridge is an individual bridge, hence we only need to parse one port.
Link: https://lore.kernel.org/r/20210823032800.1660-5-chuanjia.liu@mediatek.com
Signed-off-by: Chuanjia Liu <chuanjia.liu@mediatek.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Use platform_get_irq_byname() to get the irq number
if the "interrupt-names" property is defined.
Link: https://lore.kernel.org/r/20210823032800.1660-4-chuanjia.liu@mediatek.com
Signed-off-by: Chuanjia Liu <chuanjia.liu@mediatek.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
For the new dts format, add a new method to get
shared pcie-cfg base address and use it to configure
the PCIECFG controller
Link: https://lore.kernel.org/r/20210823032800.1660-3-chuanjia.liu@mediatek.com
Signed-off-by: Chuanjia Liu <chuanjia.liu@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
irq_mask and irq_unmask callbacks need to be properly guarded by raw spin
locks as masking/unmasking procedure needs atomic read-modify-write
operation on hardware register.
Link: https://lore.kernel.org/r/20210820155020.3000-1-pali@kernel.org
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Now we have everything we need, just provide a proper sysdata type for
the bus to use on ARM64 and everything else works.
Link: https://lore.kernel.org/r/20210726180657.142727-9-boqun.feng@gmail.com
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Since PCI_HYPERV depends on PCI_MSI_IRQ_DOMAIN which selects
GENERIC_MSI_IRQ_DOMAIN, we can use dev_set_msi_domain() to set up the
MSI domain at probing time, and this works for both x86 and ARM64.
Therefore use it as the preparation for ARM64 Hyper-V PCI support.
As a result, no longer need to maintain ->fwnode in x86 specific
pci_sysdata, and make hv_pcibus_device own it instead.
Link: https://lore.kernel.org/r/20210726180657.142727-8-boqun.feng@gmail.com
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
No functional change, just store and maintain the PCI domain number in
the ->domain_nr of pci_host_bridge. Note that we still need to keep
the copy of domain number in x86-specific pci_sysdata, because x86 is
not a PCI_DOMAINS_GENERIC=y architecture, so the ->domain_nr of
pci_host_bridge doesn't work for it yet.
Link: https://lore.kernel.org/r/20210726180657.142727-7-boqun.feng@gmail.com
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
In order to support ARM64 Hyper-V PCI, we need to set up the bridge at
probing time because ARM64 is a PCI_DOMAIN_GENERIC=y arch and we don't
have pci_config_window (ARM64 sysdata) for a PCI root bus on Hyper-V, so
it's impossible to retrieve the information (e.g. PCI domains, MSI
domains) from bus sysdata on ARM64 after creation.
Originally in create_root_hv_pci_bus(), pci_create_root_bus() is used to
create the root bus and the corresponding bridge based on x86 sysdata.
Now we create a bridge first and then call pci_scan_root_bus_bridge(),
which allows us to do the necessary set-ups for the bridge.
Link: https://lore.kernel.org/r/20210726180657.142727-6-boqun.feng@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add driver for Intel Keem Bay SoC PCIe controller. This controller
is based on DesignWare PCIe core.
In Root Complex mode, only internal reference clock is possible for
Keem Bay A0. For Keem Bay B0, external reference clock can be used
and will be the default configuration. Currently, keembay_pcie_of_data
structure has one member. It will be expanded later to handle this
difference.
Endpoint mode link initialization is handled by the boot firmware.
Link: https://lore.kernel.org/r/20210805211010.29484-3-srikanth.thokala@intel.com
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Srikanth Thokala <srikanth.thokala@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In commit 6df6ba974a ("PCI: aardvark: Remove PCIe outbound window
configuration") was removed aardvark PCIe outbound window configuration and
commit description said that was recommended solution by HW designers.
But that commit completely removed support for configuring PCIe IO
resources without removing PCIe IO 'ranges' from DTS files. After that
commit PCIe IO space started to be treated as PCIe MEM space and accessing
it just caused kernel crash.
Moreover implementation of PCIe outbound windows prior that commit was
incorrect. It completely ignored offset between CPU address and PCIe bus
address and expected that in DTS is CPU address always same as PCIe bus
address without doing any checks. Also it completely ignored size of every
PCIe resource specified in 'ranges' DTS property and expected that every
PCIe resource has size 128 MB (also for PCIe IO range). Again without any
check. Apparently none of PCIe resource has in DTS specified size of 128
MB. So it was completely broken and thanks to how aardvark mask works,
configuration was completely ignored.
This patch reverts back support for PCIe outbound window configuration but
implementation is a new without issues mentioned above. PCIe outbound
window is required when DTS specify in 'ranges' property non-zero offset
between CPU and PCIe address space. To address recommendation by HW
designers as specified in commit description of 6df6ba974a, set default
outbound parameters as PCIe MEM access without translation and therefore
for this PCIe 'ranges' it is not needed to configure PCIe outbound window.
For PCIe IO space is needed to configure aardvark PCIe outbound window.
This patch fixes kernel crash when trying to access PCIe IO space.
Link: https://lore.kernel.org/r/20210624215546.4015-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # 6df6ba974a ("PCI: aardvark: Remove PCIe outbound window configuration")
AM64 has the same PCIe IP as in J7200 with certain erratas not
applicable (quirk_detect_quiet_flag). Add support for "ti,am64-pcie-host"
compatible and "ti,am64-pcie-ep" compatible that is specific to AM64.
Link: https://lore.kernel.org/r/20210811123336.31357-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
J7200 has the same PCIe IP as in J721E with minor changes in the
wrapper. J7200 allows byte access of bridge configuration space
registers and the register field for LINK_DOWN interrupt is different.
J7200 also requires "quirk_detect_quiet_flag" to be set. Configure these
changes as part of driver data applicable only to J7200.
Link: https://lore.kernel.org/r/20210811123336.31357-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PCIe fails to link up if SERDES lanes not used by PCIe are assigned to
another protocol. For example, link training fails if lanes 2 and 3 are
assigned to another protocol while lanes 0 and 1 are used for PCIe to
form a two lane link. This failure is due to an incorrect tie-off on an
internal status signal indicating electrical idle.
Status signals going from SERDES to PCIe Controller are tied-off when a
lane is not assigned to PCIe. Signal indicating electrical idle is
incorrectly tied-off to a state that indicates non-idle. As a result,
PCIe sees unused lanes to be out of electrical idle and this causes
LTSSM to exit Detect.Quiet state without waiting for 12ms timeout to
occur. If a receiver is not detected on the first receiver detection
attempt in Detect.Active state, LTSSM goes back to Detect.Quiet and
again moves forward to Detect.Active state without waiting for 12ms as
required by PCIe base specification. Since wait time in Detect.Quiet is
skipped, multiple receiver detect operations are performed back-to-back
without allowing time for capacitance on the transmit lines to
discharge. This causes subsequent receiver detection to always fail even
if a receiver gets connected eventually.
Add a quirk flag "quirk_detect_quiet_flag" to program the minimum
time the LTSSM should wait on entering Detect.Quiet state here.
This has to be set for J7200 as it has an incorrect tie-off on unused
lanes.
Link: https://lore.kernel.org/r/20210811123336.31357-3-kishon@ti.com
Signed-off-by: Nadeem Athani <nadeem@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Now that support for SR-IOV is added in PCIe endpoint core, add support
to configure virtual functions in the Cadence PCIe EP driver.
Link: https://lore.kernel.org/r/20210819123343.1951-7-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
No functional change. Simplify code to get register base address for
configuring PCI BAR.
Link: https://lore.kernel.org/r/20210819123343.1951-6-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add virtual function number in pci_epc ops. EPC controller driver
can perform virtual function specific initialization based on the
virtual function number.
Link: https://lore.kernel.org/r/20210819123343.1951-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When the link is in L1, hardware should return it to L0
automatically whenever a transaction targets a component on the
other end of the link (PCIe r5.0, sec 5.2).
The R-Car PCIe controller doesn't handle this transition correctly.
If the link is not in L0, an MMIO transaction targeting a downstream
device fails, and the controller reports an ARM imprecise external
abort.
Work around this by hooking the abort handler so the driver can
detect this situation and help the hardware complete the link state
transition.
When the R-Car controller receives a PM_ENTER_L1 DLLP from the
downstream component, it sets PMEL1RX bit in PMSR register, but then
the controller enters some sort of in-between state. A subsequent
MMIO transaction will fail, resulting in the external abort. The
abort handler detects this condition and completes the link state
transition by setting the L1IATN bit in PMCTLR and waiting for the
link state transition to complete.
Link: https://lore.kernel.org/r/20210815181650.132579-1-marek.vasut@gmail.com
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
Hyper-V vPCI protocol version 1_4 adds support for create interrupt
v3. Create interrupt v3 essentially makes the size of the vector
field bigger in the message, thereby allowing bigger vector values.
For example, that will come into play for supporting LPI vectors
on ARM, which start at 8192.
Link: https://lore.kernel.org/r/MW4PR21MB20026A6EA554A0B9EC696AA8C0159@MW4PR21MB2002.namprd21.prod.outlook.com
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Enable PCIe reference clock. There is no remove function that's why
this should be enough for simple operation.
Normally this clock is enabled by default by firmware but there are
usecases where this clock should be enabled by driver itself.
It is also good that PCIe clock is recorded in a clock framework.
Link: https://lore.kernel.org/r/ee6997a08fab582b1c6de05f8be184f3fe8d5357.1624618100.git.michal.simek@xilinx.com
Fixes: ab597d35ef ("PCI: xilinx-nwl: Add support for Xilinx NWL PCIe Host Controller")
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
When both the old and the new PCI drivers are enabled
in the same kernel, there are a couple of namespace
conflicts that cause a build failure:
drivers/pci/controller/pci-ixp4xx.c:38: error: "IXP4XX_PCI_CSR" redefined [-Werror]
38 | #define IXP4XX_PCI_CSR 0x1c
|
In file included from arch/arm/mach-ixp4xx/include/mach/hardware.h:23,
from arch/arm/mach-ixp4xx/include/mach/io.h:15,
from arch/arm/include/asm/io.h:198,
from include/linux/io.h:13,
from drivers/pci/controller/pci-ixp4xx.c:20:
arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h:221: note: this is the location of the previous definition
221 | #define IXP4XX_PCI_CSR(x) ((volatile u32 *)(IXP4XX_PCI_CFG_BASE_VIRT+(x)))
|
drivers/pci/controller/pci-ixp4xx.c:148:12: error: 'ixp4xx_pci_read' redeclared as different kind of symbol
148 | static int ixp4xx_pci_read(struct ixp4xx_pci *p, u32 addr, u32 cmd, u32 *data)
| ^~~~~~~~~~~~~~~
Rename both the ixp4xx_pci_read/ixp4xx_pci_write functions and the
IXP4XX_PCI_CSR macro. In each case, I went with the version that
has fewer callers to keep the change small.
Fixes: f7821b4934 ("PCI: ixp4xx: Add a new driver for IXP4xx")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: soc@kernel.org
Link: https://lore.kernel.org/r/20210721151546.2325937-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
pm_runtime_get_sync() will increase the runtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Link: https://lore.kernel.org/r/20210408072402.15069-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
devm_ioremap_resource() internally calls __devm_ioremap_resource() which
is where error checking and handling is actually taking place. i
Therefore, the dev_err() call in xgene_msi_probe() is redundant.
Remove it.
Link: https://lore.kernel.org/r/20210408132751.1198171-1-yangerkun@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ErKun Yang <yangerkun@huawei.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Don't populate the array err_msg on the stack but instead make it
static. Makes the object code smaller by 64 bytes.
While at it, add a missing const, as reported by checkpatch.
Compiled with gcc 11.0.1
Before:
$ size drivers/pci/controller/pci-tegra.o
text data bss dec hex filename
25623 2844 32 28499 6f53 drivers/pci/controller/pci-tegra.o
After:
$ size drivers/pci/controller/pci-tegra.o
text data bss dec hex filename
25559 2844 32 28435 6f13 drivers/pci/controller/pci-tegra.o
Link: https://lore.kernel.org/r/5f3f35296b944b94546cc7d1e9cc6186484620d8.1620148539.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Commit 9e38e690ac ("PCI: tegra: Fix OF node reference leak") has fixed
some node reference leaks in this function but missed some of them.
In fact, having 'port' referenced in the 'rp' structure is not enough to
prevent the leak, until 'rp' is actually added in the 'pcie->ports' list.
Add the missing 'goto err_node_put' accordingly.
Link: https://lore.kernel.org/r/55b11e9a7fa2987fbc0869d68ae59888954d65e2.1620148539.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Set CRSVIS flag in emulated root PCI bridge to indicate support for
Completion Retry Status.
Add check for CRSSVE flag from root PCI brige when issuing Configuration
Read Request via PIO to correctly returns fabricated CRS value as it is
required by PCIe spec.
Link: https://lore.kernel.org/r/20210722144041.12661-5-pali@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # e0d9d30b73 ("PCI: pci-bridge-emul: Fix big-endian support")
Measurements in different conditions showed that aardvark hardware PIO
response can take up to 1.44s. Increase wait timeout from 1ms to 1.5s to
ensure that we do not miss responses from hardware. After 1.44s hardware
returns errors (e.g. Completer abort).
The previous two patches fixed checking for PIO status, so now we can use
it to also catch errors which are reported by hardware after 1.44s.
After applying this patch, kernel can detect and print PIO errors to dmesg:
[ 6.879999] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100004
[ 6.896436] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100004
[ 6.913049] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100010
[ 6.929663] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100010
[ 6.953558] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100014
[ 6.970170] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100014
[ 6.994328] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100004
Without this patch kernel prints only a generic error to dmesg:
[ 5.246847] advk-pcie d0070000.pcie: config read/write timed out
Link: https://lore.kernel.org/r/20210722144041.12661-3-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 7fbcb5da81 ("PCI: aardvark: Don't rely on jiffies while holding spinlock")
There is an issue that when PCIe switch is connected to an Armada 3700
board, there will be lots of warnings about PIO errors when reading the
config space. According to Aardvark PIO read and write sequence in HW
specification, the current way to check PIO status has the following
issues:
1) For PIO read operation, it reports the error message, which should be
avoided according to HW specification.
2) For PIO read and write operations, it only checks PIO operation complete
status, which is not enough, and error status should also be checked.
This patch aligns the code with Aardvark PIO read and write sequence in HW
specification on PIO status check and fix the warnings when reading config
space.
[pali: Fix CRS handling when CRSSVE is not enabled]
Link: https://lore.kernel.org/r/20210722144041.12661-2-pali@kernel.org
Tested-by: Victor Gu <xigu@marvell.com>
Signed-off-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # b1bd571447 ("PCI: aardvark: Indicate error in 'val' when config read fails")
When Tegra PCIe is in endpoint mode it should be available for root port.
PCIe link up by root port fails if it is in suspend state. So, don't allow
Tegra to suspend when endpoint mode is enabled.
Link: https://lore.kernel.org/r/20210623100525.19944-5-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
In suspend_noirq() call if link doesn't goto L2, PERST# is asserted
to bring link to detect state. However, this is causing surprise
link down AER error. Since Kernel is executing noirq suspend calls,
AER interrupt is not processed. PME and AER are shared interrupts
and PCIe subsystem driver enables wake capability of PME irq during
suspend. So this AER will cause suspend failure due to pending
AER interrupt.
After PCIe link is in L2, interrupts are not expected since PCIe
controller will be in reset state. Disable PCIe interrupts before
going to L2 state to avoid pending AER interrupt.
Link: https://lore.kernel.org/r/20210623100525.19944-4-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
Lower order MSI-X address is programmed in MSIX_ADDR_MATCH_HIGH_OFF
DBI register instead of higher order address. This patch fixes this
programming mistake.
Link: https://lore.kernel.org/r/20210623100525.19944-3-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
In tegra_pcie_ep_hard_irq(), APPL_INTR_STATUS_L0 is stored in val and again
APPL_INTR_STATUS_L1_0_0 is also stored in val. So when execution reaches
"if (val & APPL_INTR_STATUS_L0_PCI_CMD_EN_INT)", val is not correct.
Link: https://lore.kernel.org/r/20210623100525.19944-2-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
In commit 7ef1c871da ("PCI: iproc: Use
pci_parse_request_of_pci_ranges()"), calling
devm_request_pci_bus_resources() was dropped from the common iProc
probe code, but is still needed for BCMA bus probing. Without it, there
will be lots of warnings like this:
pci 0000:00:00.0: BAR 8: no space for [mem size 0x00c00000]
pci 0000:00:00.0: BAR 8: failed to assign [mem size 0x00c00000]
Add back calling devm_request_pci_bus_resources() and adding the
resources to pci_host_bridge.windows for BCMA bus probe.
Link: https://lore.kernel.org/r/20210803215656.3803204-2-robh@kernel.org
Fixes: 7ef1c871da ("PCI: iproc: Use pci_parse_request_of_pci_ranges()")
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Cc: Roman Bacik <roman.bacik@broadcom.com>
Cc: Bharat Gooty <bharat.gooty@broadcom.com>
Cc: Abhishek Shah <abhishek.shah@broadcom.com>
Cc: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Cc: Ray Jui <ray.jui@broadcom.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: BCM Kernel Feedback <bcm-kernel-feedback-list@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: "Krzysztof Wilczyński" <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Link: https://lore.kernel.org/r/20210802162630.2219813-4-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Following the code refactoring completed in the commit 1fd92928ba
("PCI: tegra: Refactor configuration space mapping code") there are no
more known users of struct tegra_pcie_bus.
Thus, remove declaration of struct tegra_pcie_bus as it's no longer
needed and does not have any existing users left.
Link: https://lore.kernel.org/r/20210704235733.2514131-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The Intel IXP4xx PCI controller is only present on Intel IXP4xx
XScale-based network processor SoCs.
Add a dependency on ARCH_IXP4XX, to prevent asking the user about this
driver when configuring a kernel without support for the XScale
processor family.
Link: https://lore.kernel.org/r/6a88e55fe58fc280f4ff1ca83c154e4895b6dcbf.1624972789.git.geert+renesas@glider.be
Fixes: f7821b4934 ("PCI: ixp4xx: Add a new driver for IXP4xx")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the end
of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing legacy
mach/* include dependencies and moving platform detection/config to
drivers/soc. Also some updates/cleanup of platform data.
- Core power domain support for Tegra platforms, and some improvements
in build test coverage by adding stubs for compile test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI) SMP
support on i.MX7D, SoC ID setup for i.MX50, removal of platform data
and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip.
-----BEGIN PGP SIGNATURE-----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=b6Jo
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Olof Johansson:
"A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the
end of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing
legacy mach/* include dependencies and moving platform
detection/config to drivers/soc. Also some updates/cleanup of
platform data.
- Core power domain support for Tegra platforms, and some
improvements in build test coverage by adding stubs for compile
test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI)
SMP support on i.MX7D, SoC ID setup for i.MX50, removal of platform
data and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip"
* tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (53 commits)
MAINTAINERS: Add myself as TEE subsystem reviewer
ixp4xx: fix spelling mistake in Kconfig "Devce" -> "Device"
hw_random: ixp4xx: Add OF support
hw_random: ixp4xx: Add DT bindings
hw_random: ixp4xx: Turn into a module
hw_random: ixp4xx: Use SPDX license tag
hw_random: ixp4xx: enable compile-testing
pata: ixp4xx: split platform data to its own header
soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h
PCI: ixp4xx: Add a new driver for IXP4xx
PCI: ixp4xx: Add device tree bindings for IXP4xx
ARM/ixp4xx: Make NEED_MACH_IO_H optional
ARM/ixp4xx: Move the virtual IObases
MAINTAINERS: ARM/MStar/Sigmastar SoCs: Add a link to the MStar tree
ARM: debug: add UART early console support for MSTAR SoCs
ARM: dts: ux500: Fix LED probing
ARM: imx: add smp support for imx7d
ARM: imx6q: drop of_platform_default_populate() from init_machine
arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
soc/tegra: fuse: Fix Tegra234-only builds
...
- Fix multi-MSI base vector number allocation (Sandor Bodo-Merle)
- Restrict multi-MSI support to uniprocessor kernel (Sandor Bodo-Merle)
* remotes/lorenzo/pci/iproc:
PCI: iproc: Support multi-MSI only on uniprocessor kernel
PCI: iproc: Fix multi-MSI base vector number allocation
- Decode PIO Posted/Non-posted Request correctly in error logging (Pali
Rohár)
- Work around incorrect Vendor ID in Marvell Armada 3700 (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Implement workaround for the readback value of VEND_ID
PCI: aardvark: Fix checking for PIO Non-posted Request
- Register IRQ handlers after device and data are ready (Javier Martinez
Canillas)
* pci/host/rockchip:
PCI: rockchip: Register IRQ handlers after device and data are ready
An IRQ handler may be called at any time after it is registered, so
anything it relies on must be ready before registration.
rockchip_pcie_subsys_irq_handler() and rockchip_pcie_client_irq_handler()
read registers in the PCIe controller, but we registered them before
turning on clocks to the controller. If either is called before the clocks
are turned on, the register reads fail and the machine hangs.
Similarly, rockchip_pcie_legacy_int_handler() uses rockchip->irq_domain,
but we installed it before initializing irq_domain.
Register IRQ handlers after their data structures are initialized and
clocks are enabled.
Found by enabling CONFIG_DEBUG_SHIRQ, which calls the IRQ handler when it
is being unregistered. An error during the probe path might cause this
unregistration and IRQ handler execution before the device or data
structure init has finished.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210608080409.1729276-1-javierm@redhat.com
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAmDa/58THHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXufBB/sGVIp1OhrtRFXeLJGJtbPPJzbh1w+K
hlDxthpN8uW7W7jyQRShiNUVwGX1QUiKBUH5g9oVKYBm0/srup4TivT2PiXPp4mC
7rPM9jcOD0ei9W2Z1/fjQvyorz37pQzq9GMF37FGqPM2mVuCl16QhdF5EqYjipCU
k34MyvjUPudmYot3gdiURyxrUljzw3KLfVXeg1Tpk0mXLZvm6OnyRn9ywgNJb+Pz
wn2+Om3hZCtccF2CUUS1LbMPFF97xy/CdAObyDuJyyXfyY7JFZ/guWBkQpi0tejQ
/+yJFYYZSo1lXV8xxB0t8LR9Vf6OxZNexn+0El4IUO4TZuAJcr4Q6fYp
=yOAz
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed-20210629' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv updates from Wei Liu:
"Just a few minor enhancement patches and bug fixes"
* tag 'hyperv-next-signed-20210629' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
PCI: hv: Add check for hyperv_initialized in init_hv_pci_drv()
Drivers: hv: Move Hyper-V extended capability check to arch neutral code
drivers: hv: Fix missing error code in vmbus_connect()
x86/hyperv: fix logical processor creation
hv_utils: Fix passing zero to 'PTR_ERR' warning
scsi: storvsc: Use blk_mq_unique_tag() to generate requestIDs
Drivers: hv: vmbus: Copy packets sent by Hyper-V out of the ring buffer
hv_balloon: Remove redundant assignment to region_start
tegra_pcie_ep_raise_msi_irq() shifted a signed 32-bit value left by 31
bits. The behavior of this is implementation-defined.
Replace the shift by BIT(), which is well-defined.
Found by cppcheck:
$ cppcheck --enable=all drivers/pci/controller/dwc/pcie-tegra194.c
Checking drivers/pci/controller/dwc/pcie-tegra194.c ...
drivers/pci/controller/dwc/pcie-tegra194.c:1829:23: portability: Shifting signed 32-bit value by 31 bits is implementation-defined behaviour. See condition at line 1826. [shiftTooManyBitsSigned]
appl_writel(pcie, (1 << irq), APPL_MSI_CTRL_1);
^
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210618160219.303092-1-jonathanh@nvidia.com
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Marvell Armada 3700 Functional Errata, Guidelines, and Restrictions
document describes in erratum 4.1 PCIe value of vendor ID (Ref #: 243):
The readback value of VEND_ID (RD0070000h [15:0]) is 1B4Bh, while it
should read 11ABh.
The firmware can write the correct value, 11ABh, through VEND_ID
(RD0076044h [15:0]).
Implement this workaround in aardvark driver for both PCI vendor id and PCI
subsystem vendor id.
This change affects and fixes PCI vendor id of emulated PCIe root bridge.
After this change emulated PCIe root bridge has correct vendor id.
Link: https://lore.kernel.org/r/20210624222621.4776-5-pali@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
PIO_NON_POSTED_REQ for PIO_STAT register is incorrectly defined. Bit 10 in
register PIO_STAT indicates the response is to a non-posted request.
Link: https://lore.kernel.org/r/20210624213345.3617-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Commit 275e88b06a ("PCI: tegra: Fix host link initialization") broke
host initialization during resume as it misses out calling the API
dw_pcie_setup_rc() which is required for host and MSI initialization.
Link: https://lore.kernel.org/r/20210504172157.29712-1-vidyas@nvidia.com
Fixes: 275e88b06a ("PCI: tegra: Fix host link initialization")
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add missing MODULE_DEVICE_TABLE definition so we generate correct modalias
for automatic loading of this driver when it is built as a module.
Link: https://lore.kernel.org/r/1620792422-16535-1-git-send-email-zou_wei@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The i.MX8MQ PCIe PHY needs 1.8V in default but can be supplied by either a
1.8V or a 3.3V regulator.
The "vph-supply" DT property tells us which external regulator supplies the
PHY. If that regulator supplies anything over 3V, enable the PHY's internal
3.3V-to-1.8V regulator.
Link: https://lore.kernel.org/r/1622771269-13844-3-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Define the length of the DBI registers and limit config space to its
length. This makes sure that the kernel does not access registers beyond
that point that otherwise would lead to an abort on the i.MX 6QuadPlus.
See commit 075af61c19 ("PCI: imx6: Limit DBI register length") that
resolves a similar issue on the i.MX 6Quad PCIe.
Link: https://lore.kernel.org/r/1613789388-2495-2-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
When devm_ioremap_resource() fails, __devm_ioremap_resource() prints an
error message including the device name, failure cause, and possibly
resource information.
Remove the error message from imx6_pcie_probe() since it's redundant.
Link: https://lore.kernel.org/r/20210511114547.5601-1-thunder.leizhen@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
The legacy PCI interrupt lines need to be enabled using PCIE_APP_IRNEN bits
13 (INTA), 14 (INTB), 15 (INTC) and 16 (INTD). The old code however was
taking (for example) "13" as raw value instead of taking BIT(13). Define
the legacy PCI interrupt bits using the BIT() macro and then use these in
PCIE_APP_IRN_INT.
Link: https://lore.kernel.org/r/20210106135540.48420-1-martin.blumenstingl@googlemail.com
Fixes: ed22aaaede ("PCI: dwc: intel: PCIe RC controller driver")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rahul Tanwar <rtanwar@maxlinear.com>
The interrupt affinity scheme used by this driver is incompatible with
multi-MSI as it implies moving the doorbell address to that of another MSI
group. This isn't possible for multi-MSI, as all the MSIs must have the
same doorbell address. As such it is restricted to systems with a single
CPU.
Link: https://lore.kernel.org/r/20210622152630.40842-2-sbodomerle@gmail.com
Fixes: fc54bae288 ("PCI: iproc: Allow allocation of multiple MSIs")
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sandor Bodo-Merle <sbodomerle@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Commit fc54bae288 ("PCI: iproc: Allow allocation of multiple MSIs")
introduced multi-MSI support with a broken allocation mechanism (it failed
to reserve the proper number of bits from the inner domain). Natural
alignment of the base vector number was also not guaranteed.
Link: https://lore.kernel.org/r/20210622152630.40842-1-sbodomerle@gmail.com
Fixes: fc54bae288 ("PCI: iproc: Allow allocation of multiple MSIs")
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Sandor Bodo-Merle <sbodomerle@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Ray Jui <ray.jui@broadcom.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Link: https://lore.kernel.org/r/1620717091-108691-1-git-send-email-zou_wei@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Add check for hv_is_hyperv_initialized() at the top of
init_hv_pci_drv(), so if the pci-hyperv driver is force-loaded on non
Hyper-V platforms, the init_hv_pci_drv() will exit immediately, without
any side effects, like assignments to hvpci_block_ops, etc.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reported-and-tested-by: Mohammad Alqayeem <mohammad.alqyeem@nutanix.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/1621984653-1210-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Trying to start a new PIO transfer by writing value 0 in PIO_START register
when previous transfer has not yet completed (which is indicated by value 1
in PIO_START) causes an External Abort on CPU, which results in kernel
panic:
SError Interrupt on CPU0, code 0xbf000002 -- SError
Kernel panic - not syncing: Asynchronous SError Interrupt
To prevent kernel panic, it is required to reject a new PIO transfer when
previous one has not finished yet.
If previous PIO transfer is not finished yet, the kernel may issue a new
PIO request only if the previous PIO transfer timed out.
In the past the root cause of this issue was incorrectly identified (as it
often happens during link retraining or after link down event) and special
hack was implemented in Trusted Firmware to catch all SError events in EL3,
to ignore errors with code 0xbf000002 and not forwarding any other errors
to kernel and instead throw panic from EL3 Trusted Firmware handler.
Links to discussion and patches about this issue:
https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?id=3c7dcdac5c50https://lore.kernel.org/linux-pci/20190316161243.29517-1-repk@triplefau.lt/https://lore.kernel.org/linux-pci/971be151d24312cc533989a64bd454b4@www.loen.fr/https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/1541
But the real cause was the fact that during link retraining or after link
down event the PIO transfer may take longer time, up to the 1.44s until it
times out. This increased probability that a new PIO transfer would be
issued by kernel while previous one has not finished yet.
After applying this change into the kernel, it is possible to revert the
mentioned TF-A hack and SError events do not have to be caught in TF-A EL3.
Link: https://lore.kernel.org/r/20210608203655.31228-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 7fbcb5da81 ("PCI: aardvark: Don't rely on jiffies while holding spinlock")
7f10074474 ("PCI: tegra: Add Tegra194 MCFG quirks for ECAM errata")
caused a few build regressions:
- 7f10074474 removed the Makefile rule for CONFIG_PCIE_TEGRA194, so
pcie-tegra.c can no longer be built as a module. Restore that rule.
- 7f10074474 added "#ifdef CONFIG_PCIE_TEGRA194" around the native
driver, but that's only set when the driver is built-in (for a module,
CONFIG_PCIE_TEGRA194_MODULE is defined).
The ACPI quirk is completely independent of the rest of the native
driver, so move the quirk to its own file and remove the #ifdef in the
native driver.
- 7f10074474 added symbols that are always defined but used only when
CONFIG_PCIEASPM, which causes warnings when CONFIG_PCIEASPM is not set:
drivers/pci/controller/dwc/pcie-tegra194.c:259:18: warning: ‘event_cntr_data_offset’ defined but not used [-Wunused-const-variable=]
drivers/pci/controller/dwc/pcie-tegra194.c:250:18: warning: ‘event_cntr_ctrl_offset’ defined but not used [-Wunused-const-variable=]
drivers/pci/controller/dwc/pcie-tegra194.c:243:27: warning: ‘pcie_gen_freq’ defined but not used [-Wunused-const-variable=]
Fixes: 7f10074474 ("PCI: tegra: Add Tegra194 MCFG quirks for ECAM errata")
Link: https://lore.kernel.org/r/20210610064134.336781-1-jonathanh@nvidia.com
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
This adds a new PCI controller driver for the Intel IXP4xx
(IX425, IXP435 etc), based on the XScale microarchitecture.
This replaces the old driver in arch/arm/mach-ixp4xx/common-pci.c
which utilized the ARM-specific BIOS32 PCI framework,
and all parameterization for such things as memory and
IO space as well as interrupt swizzling is done from the
device tree.
The plan is to phase out and delete the old driver piecemal.
The __raw_writel() and __raw_readl() are used for accessing
the PCI controller for the same reason that these accessors
are used in the timer, IRQ and GPIO drivers: the platform
will alter its address bus pattern based on whether the
system is booted in big- or little-endian mode. For this
reason all register on IXP4xx must always be accessed in
native (CPU) endianness.
This driver supports 64MB of PCI memory space, but not the
indirect access of 1GB that is available in the old driver.
We can address that later if and only if there are users
that need all 1GB of PCI address space. Krzysztof reports
having to use indirect MMIO only once for a VGA card. There
is work ongoing for general indirect MMIO. (In practice
the indirect MMIO is performed by writing address and
writing and reading values into/from a controller
register.)
Tested by booting the NSLU2, attaching a USB stick, mounting
and browsing the drive.
Link: https://lore.kernel.org/linux-arm-kernel/m37edwuv8m.fsf@t19.piap.pl/
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khalasa@piap.pl>
Cc: Zoltan HERPAI <wigyori@uid0.hu>
Cc: Raylynn Knight <rayknight@me.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the new method of flushing/stopping the workqueue before doing bus
removal, the old mechanism of using refcount and wait for completion
is no longer needed. Remove those dead code.
Link: https://lore.kernel.org/r/1620806809-31055-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Long Li <longli@microsoft.com>
[lorenzo.pieralisi@arm.com: Reworded subject]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
On removing the device, any work item (hv_pci_devices_present() or
hv_pci_eject_device()) scheduled on workqueue hbus->wq may still be running
and race with hv_pci_remove().
This can happen because the host may send PCI_EJECT or PCI_BUS_RELATIONS(2)
and decide to rescind the channel immediately after that.
Fix this by flushing/destroying the workqueue of hbus before doing hbus remove.
Link: https://lore.kernel.org/r/1620806800-30983-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Link: https://lore.kernel.org/r/20210511122453.6052-1-thunder.leizhen@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
PCI_IOSIZE is defined in mach-loongson64/spaces.h, so change the name
of the PCI_* macros in pci-ftpci100.c to use FTPCI_* so that they are
more localized and won't conflict with other drivers or arches.
../drivers/pci/controller/pci-ftpci100.c:37: warning: "PCI_IOSIZE" redefined
37 | #define PCI_IOSIZE 0x00
|
In file included from ../arch/mips/include/asm/addrspace.h:13,
... from ../drivers/pci/controller/pci-ftpci100.c:15:
arch/mips/include/asm/mach-loongson64/spaces.h:11: note: this is the location of the previous definition
11 | #define PCI_IOSIZE SZ_16M
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210517234117.3660-1-rdunlap@infradead.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
The PCIe host controller driver for Layerscape 4th generation SoC was
added in the commit d29ad70a81 ("PCI: mobiveil: Add PCIe Gen4 RC
driver for Layerscape SoCs").
At this time two static functions were introduced that appear to
currently have no users. Since nothing is using neither of these
functions at the moment they can be safely removed.
This resolves the following build time warnings:
drivers/pci/controller/mobiveil/pcie-layerscape-gen4.c:45:19: warning: unused function 'ls_pcie_g4_lut_readl' [-Wunused-function]
drivers/pci/controller/mobiveil/pcie-layerscape-gen4.c:50:20: warning: unused function 'ls_pcie_g4_lut_writel' [-Wunused-function]
Link: https://lore.kernel.org/r/20210510023032.3063932-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The struct event_descs does not have any users outside the
pcie-microchip-host.c file, and has no previous declaration,
thus it can be made static.
This resolves the following sparse warning:
drivers/pci/controller/pcie-microchip-host.c:352:3: warning: symbol 'event_descs' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20210509041932.560340-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
- Add reset_control_rearm() stub for !CONFIG_RESET_CONTROLLER (Jim Quinlan)
- Fix use of BCM7216 reset controller (Jim Quinlan)
- Use reset/rearm for Broadcom STB pulse reset instead of deassert/assert
(Jim Quinlan)
* pci/brcmstb:
PCI: brcmstb: Use reset/rearm instead of deassert/assert
ata: ahci_brcm: Fix use of BCM7216 reset controller
reset: add missing empty function reset_control_rearm()
- Convert tegra to MSI domains (Marc Zyngier)
- Use rcar controller address as MSI doorbell instead of allocating a page
(Marc Zyngier)
- Convert rcar to MSI domains (Marc Zyngier)
- Use xilinx port structure as MSI doorbell instead of allocating a page
(Marc Zyngier)
- Convert xilinx to MSI domains (Marc Zyngier)
- Remove unused Hyper-V msi_controller structure (Marc Zyngier)
- Remove unused PCI core msi_controller support (Marc Zyngier)
- Remove struct msi_controller (Marc Zyngier)
- Remove unused default_teardown_msi_irqs() (Marc Zyngier)
- Let host bridges declare their reliance on MSI domains (Marc Zyngier)
- Make pci_host_common_probe() declare its reliance on MSI domains (Marc
Zyngier)
- Advertise mediatek lack of built-in MSI handling (Thomas Gleixner)
- Document ways of ending up with NO_MSI (Marc Zyngier)
- Refactor HT advertising of NO_MSI flag (Marc Zyngier)
* remotes/lorenzo/pci/msi:
PCI: Refactor HT advertising of NO_MSI flag
PCI/MSI: Document the various ways of ending up with NO_MSI
PCI: mediatek: Advertise lack of built-in MSI handling
PCI/MSI: Make pci_host_common_probe() declare its reliance on MSI domains
PCI/MSI: Let PCI host bridges declare their reliance on MSI domains
PCI/MSI: Kill default_teardown_msi_irqs()
PCI/MSI: Kill msi_controller structure
PCI/MSI: Drop use of msi_controller from core code
PCI: hv: Drop msi_controller structure
PCI: xilinx: Convert to MSI domains
PCI: xilinx: Don't allocate extra memory for the MSI capture address
PCI: rcar: Convert to MSI domains
PCI: rcar: Don't allocate extra memory for the MSI capture address
PCI: tegra: Convert to MSI domains
- Program IRTE with Requester ID of VMD endpoint, not child device (Jon
Derrick)
- Disable VMD MSI-X remapping when possible so children can use more MSI-X
vectors (Jon Derrick)
* remotes/lorenzo/pci/vmd:
PCI: vmd: Disable MSI-X remapping when possible
iommu/vt-d: Use Real PCI DMA device for IRTE
- Make several microchip symbols static (Wei Yongjun)
- Drop redundant dev_err() for platform_get_irq() errors (Krzysztof
Wilczyński)
* remotes/lorenzo/pci/microchip:
PCI: microchip: Remove dev_err() when handing an error from platform_get_irq()
PCI: microchip: Make some symbols static
- Configure FC and FTS for functions other than 0 (Ryder Lee)
- Add missing MODULE_DEVICE_TABLE (Qiheng Lin)
- Add YAML schema for MediaTek (Jianjun Wang)
- Export pci_pio_to_address() for module use (Jianjun Wang)
- Add MediaTek MT8192 PCIe controller driver (Jianjun Wang)
- Add MediaTek MT8192 INTx support (Jianjun Wang)
- Add MediaTek MT8192 MSI support (Jianjun Wang)
- Add MediaTek MT8192 system power management support (Jianjun Wang)
* remotes/lorenzo/pci/mediatek:
MAINTAINERS: Add Jianjun Wang as MediaTek PCI co-maintainer
PCI: mediatek-gen3: Add system PM support
PCI: mediatek-gen3: Add MSI support
PCI: mediatek-gen3: Add INTx support
PCI: mediatek-gen3: Add MediaTek Gen3 driver for MT8192
PCI: Export pci_pio_to_address() for module use
dt-bindings: PCI: mediatek-gen3: Add YAML schema
PCI: mediatek: Add missing MODULE_DEVICE_TABLE
PCI: mediatek: Configure FC and FTS for functions other than 0
- Return zero for success of iproc_msi_irq_domain_alloc() (Pali Rohár)
* remotes/lorenzo/pci/iproc:
PCI: iproc: Fix return value of iproc_msi_irq_domain_alloc()
- Use generic config accessors for TI AM65x (K3) to fix regression (Kishon
Vijay Abraham I)
- Move MSI Receiver init to dw_pcie_host_init() so it is re-initialized
along with the RC in resume (Jisheng Zhang)
- Remove unused pcie_app_rd() (Jiapeng Chong)
- Move iATU detection earlier to fix regression (Hou Zhiqiang)
* remotes/lorenzo/pci/dwc:
PCI: dwc: Move iATU detection earlier
PCI: dwc/intel-gw: Remove unused function
PCI: dwc: Move dw_pcie_msi_init() to dw_pcie_setup_rc()
PCI: keystone: Let AM65 use the pci_ops defined in pcie-designware-host.c
- Add DT binding and TI j721e support for refclk to PCIe connector (Kishon
Vijay Abraham I)
- Add host mode and endpoint mode DT bindings for TI AM64 SoC (Kishon Vijay
Abraham I)
* remotes/lorenzo/pci/cadence:
PCI: j721e: Add support to provide refclk to PCIe connector
dt-bindings: PCI: ti,j721e: Add endpoint mode dt-bindings for TI's AM64 SoC
dt-bindings: PCI: ti,j721e: Add host mode dt-bindings for TI's AM64 SoC
dt-bindings: PCI: ti,j721e: Add binding to represent refclk to the connector
Add driver for the SiFive FU740 PCIe host controller.
This controller is based on the DesignWare PCIe core.
Co-developed-by: Henry Styles <hes@sifive.com>
Co-developed-by: Erik Danie <erik.danie@sifive.com>
Co-developed-by: Greentime Hu <greentime.hu@sifive.com>
Link: https://lore.kernel.org/r/20210504105940.100004-6-greentime.hu@sifive.com
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Henry Styles <hes@sifive.com>
Signed-off-by: Erik Danie <erik.danie@sifive.com>
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The Broadcom STB PCIe RC uses a reset control "rescal" for certain chips.
The "rescal" implements a "pulse reset" so using assert/deassert is wrong
for this device. Instead, we use reset/rearm. We need to use rearm so
that we can reset it after a suspend/resume cycle; w/o using "rearm", the
"rescal" device will only ever fire once.
Of course for suspend/resume to work we also need to put the reset/rearm
calls in the suspend and resume routines.
Fixes: 740d6c3708 ("PCI: brcmstb: Add control of rescal reset")
Link: https://lore.kernel.org/r/20210430152156.21162-4-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Add suspend_noirq and resume_noirq callback functions to implement PM
system suspend and resume hooks for the MediaTek Gen3 PCIe controller.
When the system suspends, trigger the PCIe link to enter the L2 state
and pull down the PERST# pin, gating the clocks of the MAC layer, and
then power-off the physical layer to provide power-saving.
When the system resumes, the PCIe link should be re-established and the
related control register values should be restored.
Link: https://lore.kernel.org/r/20210420061723.989-7-jianjun.wang@mediatek.com
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Add INTx support for MediaTek Gen3 PCIe controller.
Link: https://lore.kernel.org/r/20210420061723.989-5-jianjun.wang@mediatek.com
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
MediaTek's PCIe host controller has three generation HWs, the new
generation HW is an individual bridge, it supports Gen3 speed and
compatible with Gen2, Gen1 speed.
Add support for new Gen3 controller which can be found on MT8192.
Link: https://lore.kernel.org/r/20210420061723.989-4-jianjun.wang@mediatek.com
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
dw_pcie_ep_init() depends on the detected iATU region numbers to allocate
the in/outbound window management bitmap. It fails after 281f1f99cf
("PCI: dwc: Detect number of iATU windows").
Move the iATU region detection into a new function, move the detection to
the very beginning of dw_pcie_host_init() and dw_pcie_ep_init(). Also
remove it from the dw_pcie_setup(), since it's more like a software
initialization step than hardware setup.
Link: https://lore.kernel.org/r/20210125044803.4310-1-Zhiqiang.Hou@nxp.com
Link: https://lore.kernel.org/linux-pci/20210407131255.702054-1-dmitry.baryshkov@linaro.org
Link: https://lore.kernel.org/r/20210413142219.2301430-1-dmitry.baryshkov@linaro.org
Fixes: 281f1f99cf ("PCI: dwc: Detect number of iATU windows")
Tested-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[DB: moved dw_pcie_iatu_detect to happen after host_init callback]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: stable@vger.kernel.org # v5.11+
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
If the host which makes use of IP's integrated MSI Receiver losts
power during suspend, we need to reinit the RC and MSI Receiver in
resume. But after we move dw_pcie_msi_init() into the core, we have no
API to do so. Usually the dwc users need to call dw_pcie_setup_rc() to
reinit the RC, we can solve this problem by moving dw_pcie_msi_init()
to dw_pcie_setup_rc().
Link: https://lore.kernel.org/r/20210325152604.6e79deba@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
- Clean up list_sort prototypes (Sami Tolvanen)
- Introduce CONFIG_CFI_CLANG for arm64 (Sami Tolvanen)
-----BEGIN PGP SIGNATURE-----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=wU6U
-----END PGP SIGNATURE-----
Merge tag 'cfi-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull CFI on arm64 support from Kees Cook:
"This builds on last cycle's LTO work, and allows the arm64 kernels to
be built with Clang's Control Flow Integrity feature. This feature has
happily lived in Android kernels for almost 3 years[1], so I'm excited
to have it ready for upstream.
The wide diffstat is mainly due to the treewide fixing of mismatched
list_sort prototypes. Other things in core kernel are to address
various CFI corner cases. The largest code portion is the CFI runtime
implementation itself (which will be shared by all architectures
implementing support for CFI). The arm64 pieces are Acked by arm64
maintainers rather than coming through the arm64 tree since carrying
this tree over there was going to be awkward.
CFI support for x86 is still under development, but is pretty close.
There are a handful of corner cases on x86 that need some improvements
to Clang and objtool, but otherwise works well.
Summary:
- Clean up list_sort prototypes (Sami Tolvanen)
- Introduce CONFIG_CFI_CLANG for arm64 (Sami Tolvanen)"
* tag 'cfi-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
arm64: allow CONFIG_CFI_CLANG to be selected
KVM: arm64: Disable CFI for nVHE
arm64: ftrace: use function_nocfi for ftrace_call
arm64: add __nocfi to __apply_alternatives
arm64: add __nocfi to functions that jump to a physical address
arm64: use function_nocfi with __pa_symbol
arm64: implement function_nocfi
psci: use function_nocfi for cpu_resume
lkdtm: use function_nocfi
treewide: Change list_sort to use const pointers
bpf: disable CFI in dispatcher functions
kallsyms: strip ThinLTO hashes from static functions
kthread: use WARN_ON_FUNCTION_MISMATCH
workqueue: use WARN_ON_FUNCTION_MISMATCH
module: ensure __cfi_check alignment
mm: add generic function_nocfi macro
cfi: add __cficanonical
add support for Clang CFI
Almost all SoC code changes this time are for the TI OMAP
platform, which continues its decade-long quest to move from
describing a complex SoC in code to device tree.
Aside from this, the Uniphier platform has a new maintainer
and some platforms have minor bugfixes and cleanups that were
not urgent enough for v5.12.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=YFEX
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"Almost all SoC code changes this time are for the TI OMAP platform,
which continues its decade-long quest to move from describing a
complex SoC in code to device tree.
Aside from this, the Uniphier platform has a new maintainer and some
platforms have minor bugfixes and cleanups that were not urgent enough
for v5.12"
* tag 'arm-soc-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
MAINTAINERS: Update ARM/UniPhier SoCs maintainers and status
mailmap: Update email address for Nicolas Saenz
MAINTAINERS: Update BCM2711/BCM2335 maintainer's mail
ARM: exynos: correct kernel doc in platsmp
ARM: hisi: use the correct HiSilicon copyright
ARM: ux500: make ux500_cpu_die static
ARM: s3c: Use pwm_get() in favour of pwm_request() in RX1950
ARM: OMAP1: fix incorrect kernel-doc comment syntax in file
ARM: OMAP2+: fix incorrect kernel-doc comment syntax in file
ARM: OMAP2+: Use DEFINE_SPINLOCK() for spinlock
ARM: at91: pm: Move prototypes to mutually included header
ARM: OMAP2+: use true and false for bool variable
ARM: OMAP2+: add missing call to of_node_put()
ARM: OMAP2+: Replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
ARM: imx: Kconfig: Fix typo in help
ARM: mach-imx: Fix a spelling in the file pm-imx5.c
bus: ti-sysc: Warn about old dtb for dra7 and omap4/5
ARM: OMAP2+: Stop building legacy code for dra7 and omap4/5
ARM: OMAP2+: Drop legacy platform data for omap5 hwmod
ARM: OMAP2+: Drop legacy platform data for omap5 l3
...
There is not a consistent pattern for checking Hyper-V hypercall status.
Existing code uses a number of variants. The variants work, but a consistent
pattern would improve the readability of the code, and be more conformant
to what the Hyper-V TLFS says about hypercall status.
Implemented new helper functions hv_result(), hv_result_success(), and
hv_repcomp(). Changed the places where hv_do_hypercall() and related variants
are used to use the helper functions.
Signed-off-by: Joseph Salisbury <joseph.salisbury@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1618620183-9967-2-git-send-email-joseph.salisbury@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Some Mediatek host bridges cannot handle MSIs, which is sad.
This also results in an ugly warning at device probe time,
as the core PCI code wasn't told that MSIs were not available.
Advertise this fact to the rest of the core PCI code by
using the 'msi_domain' attribute, which still opens the possibility
for another block to provide the MSI functionnality.
[maz: commit message, switched over to msi_domain attribute]
Link: https://lore.kernel.org/r/20210330151145.997953-13-maz@kernel.org
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The generic PCI host driver relies on MSI domains for MSIs to
be provided to its end-points. Make this dependency explicit.
This cures the warnings occuring on arm/arm64 VMs when booted
with PCI virtio devices and no MSI controller (no GICv3 ITS,
for example).
It is likely that other drivers will need to express the same
dependency.
Link: https://lore.kernel.org/r/20210330151145.997953-12-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The Hyper-V PCI driver still makes use of a msi_controller structure,
but it looks more like a distant leftover than anything actually
useful, since it is initialised to 0 and never used for anything.
Just remove it.
Link: https://lore.kernel.org/r/20210330151145.997953-7-maz@kernel.org
Tested-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
In anticipation of the removal of the msi_controller structure, convert
the ancient xilinx host controller driver to MSI domains.
We end-up with the usual two domain structure, the top one being a
generic PCI/MSI domain, the bottom one being xilinx-specific and handling
the actual HW interrupt allocation.
This allows us to fix some of the most appaling MSI programming, where
the message programmed in the device is the virtual IRQ number instead
of the allocated vector number. The allocator is also made safe with
a mutex. This should allow support for MultiMSI, but I decided not to
even try, since I cannot test it.
Link: https://lore.kernel.org/r/20210330151145.997953-6-maz@kernel.org
Tested-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
A long cargo-culted behaviour of PCI drivers is to allocate memory
to obtain an address that is fed to the controller as the MSI
capture address (i.e. the MSI doorbell).
But there is no actual requirement for this address to be RAM.
All it needs to be is a suitable aligned address that will
*not* be DMA'd to.
Use the physical address of the 'port' data structure as the MSI
capture address, aligned on a 4K boundary.
Link: https://lore.kernel.org/r/20210330151145.997953-5-maz@kernel.org
Tested-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
In anticipation of the removal of the msi_controller structure, convert
the Rcar host controller driver to MSI domains.
We end-up with the usual two domain structure, the top one being a
generic PCI/MSI domain, the bottom one being Rcar-specific and handling
the actual HW interrupt allocation.
Link: https://lore.kernel.org/r/20210330151145.997953-4-maz@kernel.org
Tested-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
[lorenzo.pieralisi@arm.com: merged fix https://lore.kernel.org/linux-pci/87y2e2p9wk.wl-maz@kernel.org]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
A long cargo-culted behaviour of PCI drivers is to allocate memory
to obtain an address that is fed to the controller as the MSI
capture address (i.e. the MSI doorbell).
But there is no actual requirement for this address to be RAM.
All it needs to be is a suitable aligned address that will
*not* be DMA'd to.
Since the rcar platform already has a requirement that this
address should be in the first 4GB of the physical address space,
use the controller's own base address as the capture address.
Link: https://lore.kernel.org/r/20210330151145.997953-3-maz@kernel.org
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
In anticipation of the removal of the msi_controller structure, convert
the Tegra host controller driver to MSI domains.
We end-up with the usual two domain structure, the top one being a
generic PCI/MSI domain, the bottom one being Tegra-specific and handling
the actual HW interrupt allocation.
While at it, convert the normal interrupt handler to a chained handler,
handle the controller's MSI IRQ edge triggered, support multiple MSIs
per device and use the AFI_MSI_EN_VEC* registers to provide MSI masking.
[treding@nvidia.com: fix, clean up and address TODOs from Marc's draft]
Link: https://lore.kernel.org/r/20210330151145.997953-2-maz@kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe controller in Tegra194 SoC is not ECAM-compliant. With the
current hardware design, ECAM can be enabled only for one controller (the
C5 controller) with bus numbers starting from 160 instead of 0. A different
approach is taken to avoid this abnormal way of enabling ECAM for just one
controller but to enable configuration space access for all the other
controllers. In this approach, ops are added through MCFG quirk mechanism
which access the configuration spaces by dynamically programming iATU
(internal AddressTranslation Unit) to generate respective configuration
accesses just like the way it is done in DesignWare core sub-system.
This issue is specific to Tegra194 and it would be fixed in the future
generations of Tegra SoCs.
Link: https://lore.kernel.org/r/20210416134537.19474-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There is a error message within devm_ioremap_resource()
already, so remove the dev_err() call to avoid redundant
error message.
Link: https://lore.kernel.org/r/20210409075748.226141-1-clare.chenhui@huawei.com
Signed-off-by: Chen Hui <clare.chenhui@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Link: https://lore.kernel.org/r/20210331085938.3115-1-linqiheng@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
list_sort() internally casts the comparison function passed to it
to a different type with constant struct list_head pointers, and
uses this pointer to call the functions, which trips indirect call
Control-Flow Integrity (CFI) checking.
Instead of removing the consts, this change defines the
list_cmp_func_t type and changes the comparison function types of
all list_sort() callers to use const pointers, thus avoiding type
mismatches.
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210408182843.1754385-10-samitolvanen@google.com
pm_runtime_get_sync() will increase the runtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Link: https://lore.kernel.org/r/20210408072700.15791-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
In commit e2dcd20b16 a change was made to use
devm_platform_ioremap_resource_byname() to simplify code and remove
the res variable; this was wrong since the res variable is still needed
and as an outcome the port->cfg_addr gets an erroneous address.
Revert the change going back to original behaviour.
Link: https://lore.kernel.org/r/20210328144118.305074-1-zhengdejin5@gmail.com
Fixes: e2dcd20b16 ("PCI: controller: Convert to devm_platform_ioremap_resource_byname()")
Reported-by: dann.frazier@canonical.com
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v5.9+
"PCI_FUNC(port->slot << 3)" is always 0, so previously
mtk_pcie_startup_port() only configured FC credits and FTs for function
0.
Compute "func" correctly so we also configure functions other than
0. This affects MT2701 and MT7623.
Link: https://lore.kernel.org/r/c529dbfc066f4bda9b87edbdbf771f207e69b84e.1604510053.git.ryder.lee@mediatek.com
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
- Drop the dependency on PCI, as this is implied by the dependency on
PCI_MSI_IRQ_DOMAIN,
- Drop the dependencies on OF and ARM64, as the driver compiles fine
without OF and/or on other architectures,
- The Freescale Layerscape PCIe Gen4 controller is present only on
Freescale Layerscape SoCs. Hence depend on ARCH_LAYERSCAPE, to
prevent asking the user about this driver when configuring a kernel
without Freescale Layerscape support, unless compile-testing.
Link: https://lore.kernel.org/r/20210208142301.413582-1-geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
In config PCIE_TEGRA194_EP the mode incorrectly is referred to as
host mode. Fix it.
Link: https://lore.kernel.org/r/20201231032539.22322-1-wesley.sheng@amd.com
Signed-off-by: Wesley Sheng <wesley.sheng@amd.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
Fix to return negative error code -ENODEV from the unsupported revision
error handling case instead of 0, as done elsewhere in this function.
Link: https://lore.kernel.org/r/20210308135619.19133-1-weiyongjun1@huawei.com
Fixes: 0cdfaceb98 ("PCI: brcmstb: support BCM4908 with external PERST# signal controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Both TI's AM65x (K3) and TI's K2 PCIe driver are implemented in
pci-keystone. However Only K2 PCIe driver should use it's own pci_ops
for configuration space accesses. But commit 10a797c6e5
("PCI: dwc: keystone: Use pci_ops for config space accessors") used
custom pci_ops for both AM65x and K2. This breaks configuration space
access for AM65x platform. Fix it here.
Link: https://lore.kernel.org/r/20210317131518.11040-1-kishon@ti.com
Fixes: 10a797c6e5 ("PCI: dwc: keystone: Use pci_ops for config space accessors")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: <stable@vger.kernel.org> # v5.10
There is no need to call the dev_err() function directly to print a
custom message when handling an error from either the platform_get_irq()
or platform_get_irq_byname() functions as both are going to display an
appropriate error message in case of a failure.
This change is as per suggestions from Coccinelle, e.g.,
drivers/pci/controller/pcie-microchip-host.c:1027:2-9: line 1027 is
redundant because platform_get_irq() already prints an error
Related commit caecb05c80 ("PCI: Remove dev_err() when handing an
error from platform_get_irq()").
Link: https://lore.kernel.org/r/20210310131913.2802385-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The sparse tool complains as follows:
drivers/pci/controller/pcie-microchip-host.c:304:18: warning:
symbol 'pcie_event_to_event' was not declared. Should it be static?
drivers/pci/controller/pcie-microchip-host.c:310:18: warning:
symbol 'sec_error_to_event' was not declared. Should it be static?
drivers/pci/controller/pcie-microchip-host.c:317:18: warning:
symbol 'ded_error_to_event' was not declared. Should it be static?
drivers/pci/controller/pcie-microchip-host.c:324:18: warning:
symbol 'local_status_to_event' was not declared. Should it be static?
Those symbols are not used outside of pcie-microchip-host.c, so this
commit marks them static.
Link: https://lore.kernel.org/r/20210308094842.3588847-1-weiyongjun1@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
IRQ domain alloc function should return zero on success. Non-zero value
indicates failure.
Link: https://lore.kernel.org/r/20210303142202.25780-1-pali@kernel.org
Fixes: fc54bae288 ("PCI: iproc: Allow allocation of multiple MSIs")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Marc Zyngier <maz@kernel.org>
VMD will retransmit child device MSI-X using its own MSI-X table and
requester-id. This limits the number of MSI-X available to the whole
child device domain to the number of VMD MSI-X interrupts.
Some VMD devices have a mode where this remapping can be disabled,
allowing child device interrupts to bypass processing with the VMD MSI-X
domain interrupt handler and going straight the child device interrupt
handler, allowing for better performance and scaling. The requester-id
still gets changed to the VMD endpoint's requester-id, and the interrupt
remapping handlers have been updated to properly set IRTE for child
device interrupts to the VMD endpoint's context.
Some VMD platforms have existing production BIOS which rely on MSI-X
remapping and won't explicitly program the MSI-X remapping bit. This
re-enables MSI-X remapping on unload.
Link: https://lore.kernel.org/r/20210210161315.316097-3-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
The only usage of them is to assign their address to the 'ops' field in
the pcie_port and the dw_pcie_ep structs, both which are pointers to
const. Make them const to allow the compiler to put them in read-only
memory.
Link: https://lore.kernel.org/r/20210207221604.48910-1-rikard.falkeborn@gmail.com
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
The hv_compose_msi_msg() callback in irq_chip::irq_compose_msi_msg is
invoked via irq_chip_compose_msi_msg(), which itself is always invoked from
atomic contexts from the guts of the interrupt core code.
There is no way to change this w/o rewriting the whole driver, so use
tasklet_disable_in_atomic() which allows to make tasklet_disable()
sleepable once the remaining atomic users are addressed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210309084242.516519290@linutronix.de
There are harmless warnings when compile testing the kernel with
CONFIG_TRIM_UNUSED_KSYMS:
drivers/pci/controller/dwc/pcie-al.o: no symbols
drivers/pci/controller/pci-thunder-ecam.o: no symbols
drivers/pci/controller/pci-thunder-pem.o: no symbols
The problem here is that the host drivers get built even when the
configuration symbols are all disabled, as they pretend to not be drivers
but are silently enabled because of the promise that ACPI-based systems
need no drivers.
Add back the normal symbols to have these drivers built, and change the
logic to otherwise only build them when both CONFIG_PCI_QUIRKS and
CONFIG_ACPI are enabled.
As a side-effect, this enables compile-testing the drivers on other
architectures, which in turn needs the acpi_get_rc_resources() function to
be defined.
Link: https://lore.kernel.org/r/20210308152501.2135937-3-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Compile-testing these drivers is currently broken. Enabling it causes a
couple of build failures though:
drivers/pci/controller/pci-thunder-ecam.c:119:30: error: shift count >= width of type [-Werror,-Wshift-count-overflow]
drivers/pci/controller/pci-thunder-pem.c:54:2: error: implicit declaration of function 'writeq' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-thunder-pem.c:392:8: error: implicit declaration of function 'acpi_get_rc_resources' [-Werror,-Wimplicit-function-declaration]
Fix them with the obvious one-line changes.
Link: https://lore.kernel.org/r/20210308152501.2135937-2-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Compile-testing this driver without ECAM support results in a link failure:
ld.lld: error: undefined symbol: pci_ecam_map_bus
>>> referenced by pcie-al.c
>>> pci/controller/dwc/pcie-al.o:(al_pcie_map_bus) in archive drivers/built-in.a
Select CONFIG_ECAM like the other drivers do.
Link: https://lore.kernel.org/r/20210308152501.2135937-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
After updating pci-dra7xx driver to probe with ti-sysc and genpd, I
noticed that dra7xx_pcie_probe() would not run if a power-domains property
was configured for the interconnect target module.
Turns out that module_platform_driver_probe uses platform_driver_probe(),
while builtin_platform_driver uses platform_driver_register().
Only platform_driver_register() works for deferred probe as noted in the
comments for __platform_driver_probe() in drivers/base/platform.c with a
line saying "Note that this is incompatible with deferred probing".
With module_platform_driver_probe, we have platform_driver_probe() produce
-ENODEV error at device_initcall() level, and no further attempts are done.
Let's fix this by using module_platform_driver instead.
Note this is not an issue currently as we probe devices with simple-bus,
and only is needed as we start probing the device with ti-sysc, or when
probed with simple-pm-bus.
Note that we must now also remove __init for probe related functions to
avoid a section mismatch warning.
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
-----BEGIN PGP SIGNATURE-----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=GXL5
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Remove unnecessary locking around _OSC (Bjorn Helgaas)
- Clarify message about _OSC failure (Bjorn Helgaas)
- Remove notification of PCIe bandwidth changes (Bjorn Helgaas)
- Tidy checking of syscall user config accessors (Heiner Kallweit)
Resource management:
- Decline to resize resources if boot config must be preserved (Ard
Biesheuvel)
- Fix pci_register_io_range() memory leak (Geert Uytterhoeven)
Error handling (Keith Busch):
- Clear error status from the correct device
- Retain error recovery status so drivers can use it after reset
- Log the type of Port (Root or Switch Downstream) that we reset
- Always request a reset for Downstream Ports in frozen state
Endpoint framework and NTB (Kishon Vijay Abraham I):
- Make *_get_first_free_bar() take into account 64 bit BAR
- Add helper API to get the 'next' unreserved BAR
- Make *_free_bar() return error codes on failure
- Remove unused pci_epf_match_device()
- Add support to associate secondary EPC with EPF
- Add support in configfs to associate two EPCs with EPF
- Add pci_epc_ops to map MSI IRQ
- Add pci_epf_ops to expose function-specific attrs
- Allow user to create sub-directory of 'EPF Device' directory
- Implement ->msi_map_irq() ops for cadence
- Configure LM_EP_FUNC_CFG based on epc->function_num_map for cadence
- Add EP function driver to provide NTB functionality
- Add support for EPF PCI Non-Transparent Bridge
- Add specification for PCI NTB function device
- Add PCI endpoint NTB function user guide
- Add configfs binding documentation for pci-ntb endpoint function
Broadcom STB PCIe controller driver:
- Add support for BCM4908 and external PERST# signal controller
(Rafał Miłecki)
Cadence PCIe controller driver:
- Retrain Link to work around Gen2 training defect (Nadeem Athani)
- Fix merge botch in cdns_pcie_host_map_dma_ranges() (Krzysztof
Wilczyński)
Freescale Layerscape PCIe controller driver:
- Add LX2160A rev2 EP mode support (Hou Zhiqiang)
- Convert to builtin_platform_driver() (Michael Walle)
MediaTek PCIe controller driver:
- Fix OF node reference leak (Krzysztof Wilczyński)
Microchip PolarFlare PCIe controller driver:
- Add Microchip PolarFire PCIe controller driver (Daire McNamara)
Qualcomm PCIe controller driver:
- Use PHY_REFCLK_USE_PAD only for ipq8064 (Ansuel Smith)
- Add support for ddrss_sf_tbu clock for sm8250 (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Drop PCIE_RCAR config option (Lad Prabhakar)
- Always allocate MSI addresses in 32bit space (Marek Vasut)
Rockchip PCIe controller driver:
- Add FriendlyARM NanoPi M4B DT binding (Chen-Yu Tsai)
- Make 'ep-gpios' DT property optional (Chen-Yu Tsai)
Synopsys DesignWare PCIe controller driver:
- Work around ECRC configuration hardware defect (Vidya Sagar)
- Drop support for config space in DT 'ranges' (Rob Herring)
- Change size to u64 for EP outbound iATU (Shradha Todi)
- Add upper limit address for outbound iATU (Shradha Todi)
- Make dw_pcie ops optional (Jisheng Zhang)
- Remove unnecessary dw_pcie_ops from al driver (Jisheng Zhang)
Xilinx Versal CPM PCIe controller driver:
- Fix OF node reference leak (Pan Bian)
Miscellaneous:
- Remove tango host controller driver (Arnd Bergmann)
- Remove IRQ handler & data together (altera-msi, brcmstb, dwc)
(Martin Kaiser)
- Fix xgene-msi race in installing chained IRQ handler (Martin
Kaiser)
- Apply CONFIG_PCI_DEBUG to entire drivers/pci hierarchy (Junhao He)
- Fix pci-bridge-emul array overruns (Russell King)
- Remove obsolete uses of WARN_ON(in_interrupt()) (Sebastian Andrzej
Siewior)"
* tag 'pci-v5.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (69 commits)
PCI: qcom: Use PHY_REFCLK_USE_PAD only for ipq8064
PCI: qcom: Add support for ddrss_sf_tbu clock
dt-bindings: PCI: qcom: Document ddrss_sf_tbu clock for sm8250
PCI: al: Remove useless dw_pcie_ops
PCI: dwc: Don't assume the ops in dw_pcie always exist
PCI: dwc: Add upper limit address for outbound iATU
PCI: dwc: Change size to u64 for EP outbound iATU
PCI: dwc: Drop support for config space in 'ranges'
PCI: layerscape: Convert to builtin_platform_driver()
PCI: layerscape: Add LX2160A rev2 EP mode support
dt-bindings: PCI: layerscape: Add LX2160A rev2 compatible strings
PCI: dwc: Work around ECRC configuration issue
PCI/portdrv: Report reset for frozen channel
PCI/AER: Specify the type of Port that was reset
PCI/ERR: Retain status from error notification
PCI/AER: Clear AER status from Root Port when resetting Downstream Port
PCI/ERR: Clear status of the reporting device
dt-bindings: arm: rockchip: Add FriendlyARM NanoPi M4B
PCI: rockchip: Make 'ep-gpios' DT property optional
Documentation: PCI: Add PCI endpoint NTB function user guide
...
- Remove IRQ handler & data together for altera, brcmstb, dwc (Martin
Kaiser)
- Fix xgene race in installing chained IRQ handler (Martin Kaiser)
- Drop PCIE_RCAR config option (replaced by PCIE_RCAR_HOST) (Lad Prabhakar)
- Fix xgene comment about CRS vs CRS SV (Bjorn Helgaas)
* remotes/lorenzo/pci/misc:
PCI: hv: Fix typo
PCI: xgene: Fix CRS SV comment
PCI: brcmstb: Remove chained IRQ handler and data in one go
PCI: Drop PCIE_RCAR config option
PCI: xgene-msi: Fix race in installing chained irq handler
PCI: dwc: Remove IRQ handler and data in one go
PCI: altera-msi: Remove IRQ handler and data in one go
- Always allocate rcar MSI addresses in 32-bit space so legacy devices
without 64-bit MSI support can use MSI (Marek Vasut)
* remotes/lorenzo/pci/rcar:
PCI: rcar: Always allocate MSI addresses in 32bit space
- Add support for SM8250 PCIe SF TBU clock (Dmitry Baryshkov)
- Use PHY_REFCLK_USE_PAD only for qcom ipq8064 (Ansuel Smith)
* pci/qcom:
PCI: qcom: Use PHY_REFCLK_USE_PAD only for ipq8064
PCI: qcom: Add support for ddrss_sf_tbu clock
dt-bindings: PCI: qcom: Document ddrss_sf_tbu clock for sm8250
- Account for 64-bit BARs in pci_epc_get_first_free_bar() (Kishon Vijay
Abraham I)
- Add pci_epc_get_next_free_bar() helper (Kishon Vijay Abraham I)
- Return error codes on failure of endpoint BAR interfaces (Kishon Vijay
Abraham I)
- Remove unused pci_epf_match_device() (Kishon Vijay Abraham I)
- Add support for secondary endpoint controller to prepare for NTB endpoint
functionality (Kishon Vijay Abraham I)
- Add configfs support for secondary endpoint controller (Kishon Vijay
Abraham I)
- Add MSI address mapping ops for NTB doorbell support (Kishon Vijay
Abraham I)
- Add ops for endpoint function-specific attributes (Kishon Vijay Abraham
I)
- Allow configfs subdirectory for endpoint function configuration (Kishon
Vijay Abraham I)
- Implement cadence MSI address mapping ops (Kishon Vijay Abraham I)
- Configure cadence LM_EP_FUNC_CFG based on epc->function_num_map (Kishon
Vijay Abraham I)
- Add endpoint-side driver to provide NTB functionality (Kishon Vijay
Abraham I)
- Add host-side driver for generic EPF NTB functionality (Kishon Vijay
Abraham I)
- Document NTB endpoint functionality (Kishon Vijay Abraham I)
* pci/ntb:
Documentation: PCI: Add PCI endpoint NTB function user guide
Documentation: PCI: Add configfs binding documentation for pci-ntb endpoint function
NTB: Add support for EPF PCI Non-Transparent Bridge
PCI: Add TI J721E device to PCI IDs
PCI: endpoint: Add EP function driver to provide NTB functionality
PCI: cadence: Configure LM_EP_FUNC_CFG based on epc->function_num_map
PCI: cadence: Implement ->msi_map_irq() ops
PCI: endpoint: Allow user to create sub-directory of 'EPF Device' directory
PCI: endpoint: Add pci_epf_ops to expose function-specific attrs
PCI: endpoint: Add pci_epc_ops to map MSI IRQ
PCI: endpoint: Add support in configfs to associate two EPCs with EPF
PCI: endpoint: Add support to associate secondary EPC with EPF
PCI: endpoint: Remove unused pci_epf_match_device()
PCI: endpoint: Make *_free_bar() to return error codes on failure
PCI: endpoint: Add helper API to get the 'next' unreserved BAR
PCI: endpoint: Make *_get_first_free_bar() take into account 64 bit BAR
Documentation: PCI: Add specification for the PCI NTB function device
- Always set DesignWare "TLP Digest" bit so generic code can enable ECRC
via the AER Capability (Vidya Sagar)
- Drop support for config space in DT 'ranges' (Rob Herring)
- Increase width of outbound iATU size to u64 (Shradha Todi)
- Add upper limit address for outbound iATU (Shradha Todi)
- Allow dwc-based drivers that don't override any default ops (Jisheng
Zhang)
- Drop unnecessary dw_pcie_ops from the al driver (Jisheng Zhang)
* pci/dwc:
PCI: al: Remove useless dw_pcie_ops
PCI: dwc: Don't assume the ops in dw_pcie always exist
PCI: dwc: Add upper limit address for outbound iATU
PCI: dwc: Change size to u64 for EP outbound iATU
PCI: dwc: Drop support for config space in 'ranges'
PCI: dwc: Work around ECRC configuration issue
- Retrain Link to work around Gen2 training defect (Nadeem Athani)
* remotes/lorenzo/pci/cadence:
PCI: cadence: Retrain Link to work around Gen2 training defect
- Add support for BCM4908 with external PERST# signal controller (Rafał
Miłecki)
* remotes/lorenzo/pci/brcmstb:
PCI: brcmstb: support BCM4908 with external PERST# signal controller
dt-bindings: PCI: brcmstb: add BCM4908 binding
The use of PHY_REFCLK_USE_PAD introduced a regression for apq8064 devices.
It was tested that while apq doesn't require the padding, ipq SoC must use
it or the kernel hangs on boot.
Link: https://lore.kernel.org/r/20201019165555.8269-1-ansuelsmth@gmail.com
Fixes: de3c4bf648 ("PCI: qcom: Add support for tx term offset for rev 2.1.0")
Reported-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # v4.19+
We have removed the assumption that dw_pcie_ops always exists in the dwc
core driver, so we can remove the useless dw_pcie_ops now.
Link: https://lore.kernel.org/r/20210128144324.2fa8577c@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jonathan Chocron <jonnyc@amazon.com>
Some dwc-based device drivers, especially host-only drivers, may work well
with the default read_dbi/write_dbi/link_up implementations in
pcie-designware.c, so remove the assumption that every driver implements
them to simplify those drivers.
Link: https://lore.kernel.org/r/20210128144258.10329aa4@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The size parameter is unsigned long type which can accept size > 4GB. In
that case, the upper limit address must be programmed. Add support to
program the upper limit address and set INCREASE_REGION_SIZE in case size >
4GB.
Link: https://lore.kernel.org/r/1612250918-19610-1-git-send-email-shradha.t@samsung.com
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Since outbound iATU permits size to be greater than 4GB for which the
support is also available, allow EP function to send u64 size instead of
truncating to u32.
Link: https://lore.kernel.org/r/1609929900-19082-1-git-send-email-shradha.t@samsung.com
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Since commit a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and
"addr_space" resource setup into common code"), the code
setting dbi_base when the config space is defined in 'ranges' property
instead of 'reg' is dead code as dbi_base is never NULL.
Rather than fix this, let's just drop the code. Using ranges has been
deprecated since 2014. The only platforms using this were exynos5440,
i.MX6 and Spear13xx. Exynos5440 is dead and has been removed. i.MX6 and
Spear13xx had PCIe support added just before this was deprecated and
were fixed within a kernel release or 2.
Link: https://lore.kernel.org/r/20201215194149.86831-1-robh@kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
fw_devlink will defer the probe until all suppliers are ready. We can't
use builtin_platform_driver_probe() because it doesn't retry after probe
deferral. Convert it to builtin_platform_driver().
Link: https://lore.kernel.org/r/20210120105246.23218-1-michael@walle.cc
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The LX2160A rev2 uses the same PCIe IP as LS2088A, but LX2160A rev2 PCIe
controller is integrated with different stride between PFs' register
address.
Link: https://lore.kernel.org/r/20201026051448.1913-2-Zhiqiang.Hou@nxp.com
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
DesignWare core has a TLP digest (TD) override bit in one of the control
registers of ATU. This bit also needs to be programmed for proper ECRC
functionality. This is currently identified as an issue with DesignWare
IP version 4.90a.
[bhelgaas: fix typos/grammar errors]
Link: https://lore.kernel.org/r/20201230165723.673-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The Rockchip PCIe controller DT binding clearly states that 'ep-gpios' is
an optional property. And indeed there are boards that don't require it.
Make the driver follow the binding by using devm_gpiod_get_optional()
instead of devm_gpiod_get().
[bhelgaas: tidy whitespace]
Link: https://lore.kernel.org/r/20210121162321.4538-2-wens@kernel.org
Fixes: e77f847df5 ("PCI: rockchip: Add Rockchip PCIe controller support")
Fixes: 956cd99b35 ("PCI: rockchip: Separate common code from RC driver")
Fixes: 964bac9455 ("PCI: rockchip: Split out rockchip_pcie_parse_dt() to parse DT")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The number of functions supported by the endpoint controller is configured
in LM_EP_FUNC_CFG based on func_no member of struct pci_epf. Now that an
endpoint function can be associated with two endpoint controllers (primary
and secondary), just using func_no will not suffice as that will take into
account only if the endpoint controller is associated with the primary
interface of endpoint function. Instead use epc->function_num_map which
will already have the configured functions information (irrespective of
whether the endpoint controller is associated with primary or secondary
interface).
Link: https://lore.kernel.org/r/20210201195809.7342-13-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tom Joseph <tjoseph@cadence.com>
Implement ->msi_map_irq() ops in order to map physical address to MSI
address and return MSI data.
Link: https://lore.kernel.org/r/20210201195809.7342-12-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tom Joseph <tjoseph@cadence.com>
Add support for the Microchip PolarFire PCIe controller when configured in
host (Root Complex) mode.
[bhelgaas: wrap lines to fit in 80 columns, fix trivial style issues]
Link: https://lore.kernel.org/r/20210125162934.5335-4-daire.mcnamara@microchip.com
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
[lorenzo.pieralisi@arm.com: minor comments tweak]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Many drivers can now use pci_host_common_probe() directly.
Their hardware window setup can be moved from their 'custom' probe
functions to individual driver init functions.
Link: https://lore.kernel.org/r/20210125162934.5335-2-daire.mcnamara@microchip.com
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Function cdns_pcie_host_map_dma_ranges() iterates over a PCIe host bridge
DMA ranges using the resource_list_for_each_entry() iterator, returning an
error if cdns_pcie_host_bar_config() fails.
49e427e6bd ("Merge branch 'pci/host-probe-refactor'") botched a merge so
it *always* returned after the first DMA range, even if no error occurred.
Fix the error checking so we return early only when an error occurs.
[bhelgaas: commit log]
Fixes: 49e427e6bd ("Merge branch 'pci/host-probe-refactor'")
Link: https://lore.kernel.org/r/20210216205935.3112661-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We will soon use the same structure to handle IO-APIC interrupts as
well. Introduce an enum to identify the source and a data structure for
IO-APIC RTE.
While at it, update pci-hyperv.c to use the enum.
No functional change.
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20210203150435.27941-13-wei.liu@kernel.org
Cadence controller will not initiate autonomous speed change if strapped
as Gen2. The Retrain Link bit is set as quirk to enable this speed change.
Link: https://lore.kernel.org/r/20210209144622.26683-3-nadeem@cadence.com
Signed-off-by: Nadeem Athani <nadeem@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Configuration Request Retry Status ("CRS") must be supported by all PCIe
devices. CRS Software Visibility is an optional feature that enables a
Root Port to make CRS visible to software by returning a special data value
to complete a config read.
Clarify a comment to say that it is "CRS SV", not "CRS", that can be
enabled.
Link: https://lore.kernel.org/r/20210126213503.2922848-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The for_each_available_child_of_node helper internally makes use of the
of_get_next_available_child() which performs an of_node_get() on each
iteration when searching for next available child node.
Should an available child node be found, then it would return a device
node pointer with reference count incremented, thus early return from
the middle of the loop requires an explicit of_node_put() to prevent
reference count leak.
To stop the reference leak, explicitly call of_node_put() before
returning after an error occurred.
Link: https://lore.kernel.org/r/20210120184810.3068794-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Also drop the reference count of the node on error path.
Link: https://lore.kernel.org/r/20210120143745.699-1-bianpan2016@163.com
Fixes: 508f610648 ("PCI: xilinx-cpm: Add Versal CPM Root Port driver")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The tango platform is getting removed, so the driver is no
longer needed.
Link: https://lore.kernel.org/r/20210120150800.1650898-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Call irq_set_chained_handler_and_data() to clear the chained handler
and the handler's data under irq_desc->lock.
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained
IRQ handler").
Link: https://lore.kernel.org/r/20210115211532.19837-1-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
All the defconfig files have replaced PCIE_RCAR config option with
PCIE_RCAR_HOST config option which built the same driver, so we can
now safely drop PCIE_RCAR config option.
Link: https://lore.kernel.org/r/20201229170848.18482-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
BCM4908 uses external MISC block for controlling PERST# signal. Use it
as a reset controller.
Link: https://lore.kernel.org/r/20201210180421.7230-3-zajec5@gmail.com
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained IRQ
handler").
Based on the mail discussion, it seems ok to drop the error handling.
Link: https://lore.kernel.org/r/20210115212435.19940-3-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Call irq_set_chained_handler_and_data() to clear the chained handler
and the handler's data under irq_desc->lock.
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained
IRQ handler").
Link: https://lore.kernel.org/r/20210115212435.19940-2-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Call irq_set_chained_handler_and_data() to clear the chained handler
and the handler's data under irq_desc->lock.
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained
IRQ handler").
Link: https://lore.kernel.org/r/20210115212435.19940-1-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This fixes MSI operation on legacy PCI cards, which cannot issue 64bit MSIs.
The R-Car controller only has one MSI trigger address instead of two, one
for 64bit and one for 32bit MSI, set the address to 32bit PCIe space so that
legacy PCI cards can also trigger MSIs.
Link: https://lore.kernel.org/r/20201016120431.7062-1-marek.vasut@gmail.com
Fixes: 290c1fb358 ("PCI: rcar: Add MSI support for PCIe")
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
Commit 660c486590 ("PCI: dwc: Set 32-bit DMA mask for MSI target address
allocation") added dma_mask_set() call to explicitly set 32-bit DMA mask
for MSI message mapping, but for now it throws a warning on ret == 0, while
dma_set_mask() returns 0 in case of success.
Fix this by inverting the condition.
[bhelgaas: join string to make it greppable]
Fixes: 660c486590 ("PCI: dwc: Set 32-bit DMA mask for MSI target address allocation")
Link: https://lore.kernel.org/r/20201222150708.67983-1-alobakin@pm.me
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit b9ac0f9dc8 ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common
code") broke enumeration of downstream devices on Tegra:
In non-working case (next-20201211):
0001:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad0 (rev a1)
In working case (v5.10-rc7):
0001:00:00.0 PCI bridge: Molex Incorporated Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: Molex Incorporated Device 1ad0 (rev a1)
0005:01:00.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:02:02.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:03:00.0 USB controller: PLX Technology, Inc. Device 3380 (rev ab)
The problem seems to be dw_pcie_setup_rc() is now called twice before and
after the link up handling. The fix is to move Tegra's link up handling to
.start_link() function like other DWC drivers. Tegra is a bit more
complicated than others as it re-inits the whole DWC controller to retry
the link. With this, the initialization ordering is restored to match the
prior sequence.
Fixes: b9ac0f9dc8 ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common code")
Link: https://lore.kernel.org/r/20201218143905.1614098-1-robh@kernel.org
Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Tested-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
accesses, inefficient and disfunctional code. The goal is to remove the
export of irq_to_desc() to prevent these things from creeping up again.
-----BEGIN PGP SIGNATURE-----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=BXv+
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"This is the second attempt after the first one failed miserably and
got zapped to unblock the rest of the interrupt related patches.
A treewide cleanup of interrupt descriptor (ab)use with all sorts of
racy accesses, inefficient and disfunctional code. The goal is to
remove the export of irq_to_desc() to prevent these things from
creeping up again"
* tag 'irq-core-2020-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (30 commits)
genirq: Restrict export of irq_to_desc()
xen/events: Implement irq distribution
xen/events: Reduce irq_info:: Spurious_cnt storage size
xen/events: Only force affinity mask for percpu interrupts
xen/events: Use immediate affinity setting
xen/events: Remove disfunct affinity spreading
xen/events: Remove unused bind_evtchn_to_irq_lateeoi()
net/mlx5: Use effective interrupt affinity
net/mlx5: Replace irq_to_desc() abuse
net/mlx4: Use effective interrupt affinity
net/mlx4: Replace irq_to_desc() abuse
PCI: mobiveil: Use irq_data_get_irq_chip_data()
PCI: xilinx-nwl: Use irq_data_get_irq_chip_data()
NTB/msi: Use irq_has_action()
mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc
pinctrl: nomadik: Use irq_has_action()
drm/i915/pmu: Replace open coded kstat_irqs() copy
drm/i915/lpe_audio: Remove pointless irq_to_desc() usage
s390/irq: Use irq_desc_kstat_cpu() in show_msi_interrupt()
parisc/irq: Use irq_desc_kstat_cpu() in show_interrupts()
...
-----BEGIN PGP SIGNATURE-----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=xRTv
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Decode PCIe 64 GT/s link speed (Gustavo Pimentel)
- Remove unused HAVE_PCI_SET_MWI (Heiner Kallweit)
- Reduce pci_set_cacheline_size() message to debug level (Heiner
Kallweit)
- Fix pci_slot_release() NULL pointer dereference (Jubin Zhong)
- Unify ECAM constants in native PCI Express drivers (Krzysztof
Wilczyński)
- Return u8 from pci_find_capability() and similar (Puranjay Mohan)
- Return u16 from pci_find_ext_capability() and similar (Bjorn
Helgaas)
- Fix ACPI companion lookup for device 0 on the root bus (Rafael J.
Wysocki)
Resource management:
- Keep both device and resource name for config space remaps
(Alexander Lobakin)
- Bounds-check command-line resource alignment requests (Bjorn
Helgaas)
- Fix overflow in command-line resource alignment requests (Colin Ian
King)
Driver binding:
- Avoid duplicate IDs in driver dynamic IDs list (Zhenzhong Duan)
Power management:
- Save/restore Precision Time Measurement Capability for
suspend/resume (David E. Box)
- Disable PTM during suspend to save power (David E. Box)
- Add sysfs attribute for device power state (Maximilian Luz)
- Rename pci_wakeup_bus() to pci_resume_bus() (Mika Westerberg)
- Do not generate wakeup event when runtime resuming device (Mika
Westerberg)
- Save/restore ASPM L1SS Capability for suspend/resume (Vidya Sagar)
Virtualization:
- Mark AMD Raven iGPU ATS as broken in some platforms (Alex Deucher)
- Add function 1 DMA alias quirk for Marvell 9215 SATA controller
(Bjorn Helgaas)
MSI:
- Disable MSI for Pericom PCIe-USB adapter (Andy Shevchenko)
- Improve warnings for 32-bit-limited MSI support (Vidya Sagar)
Error handling:
- Cache RCEC EA Capability offset in pci_init_capabilities() (Sean V
Kelley)
- Rename reset_link() to reset_subordinates() (Sean V Kelley)
- Write AER Capability only when we control it (Sean V Kelley)
- Clear AER status only when we control AER (Sean V Kelley)
- Bind RCEC devices to the Root Port driver (Qiuxu Zhuo)
- Recover from RCiEP AER errors (Qiuxu Zhuo)
- Recover from RCEC AER errors (Sean V Kelley)
- Add pcie_link_rcec() to associate RCiEPs (Sean V Kelley)
- Add pcie_walk_rcec() to RCEC AER handling (Sean V Kelley)
- Add pcie_walk_rcec() to RCEC PME handling (Sean V Kelley)
- Add RCEC AER error injection support (Qiuxu Zhuo)
Broadcom iProc PCIe controller driver:
- Fix out-of-bound array accesses (Bharat Gooty)
- Invalidate correct PAXB inbound windows (Roman Bacik)
- Enhance PCIe Link information display (Srinath Mannam)
Cadence PCIe controller driver:
- Make "cdns,max-outbound-regions" property optional (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Offset client MSI-X vectors (Jon Derrick)
- Update type of __iomem pointers (Krzysztof Wilczyński)
NVIDIA Tegra PCIe controller driver:
- Move "dbi" accesses to post common DWC initialization (Vidya Sagar)
- Read "dbi" base address to program in application logic (Vidya
Sagar)
- Fix ASPM-L1SS advertisement disable code (Vidya Sagar)
- Set DesignWare IP version (Vidya Sagar)
- Continue unconfig sequence even if parts fail (Vidya Sagar)
- Check return value of tegra_pcie_init_controller() (Vidya Sagar)
- Disable LTSSM during L2 entry (Vidya Sagar)
Qualcomm PCIe controller driver:
- Document PCIe bindings for SM8250 SoC (Manivannan Sadhasivam)
- Add SM8250 SoC support (Manivannan Sadhasivam)
- Add support for configuring BDF to SID mapping for SM8250
(Manivannan Sadhasivam)
Renesas R-Car PCIe controller driver:
- rcar: Drop unused members from struct rcar_pcie_host (Lad
Prabhakar)
- PCI: rcar-pci-host: Document r8a774e1 bindings (Lad Prabhakar)
- PCI: rcar-pci-host: Convert bindings to json-schema (Yoshihiro
Shimoda)
- PCI: rcar-pci-host: Document r8a77965 bindings (Yoshihiro Shimoda)
Samsung Exynos PCIe controller driver:
- Rework driver to support Exynos5433 PCIe PHY (Jaehoon Chung)
- Rework driver to support Exynos5433 variant (Jaehoon Chung)
- Drop samsung,exynos5440-pcie binding (Marek Szyprowski)
- Add the samsung,exynos-pcie binding (Marek Szyprowski)
- Add the samsung,exynos-pcie-phy binding (Marek Szyprowski)
Synopsys DesignWare PCIe controller driver:
- Support multiple ATU memory regions (Rob Herring)
- Move intel-gw ATU offset out of driver match data (Rob Herring)
- Move "dbi", "dbi2", and "addr_space" resource setup into common
code (Rob Herring)
- Remove intel-gw unneeded function wrappers (Rob Herring)
- Ensure all outbound ATU windows are reset (Rob Herring)
- Use the common MSI irq_chip in dra7xx (Rob Herring)
- Drop the .set_num_vectors() host op (Rob Herring)
- Move MSI interrupt setup into DWC common code (Rob Herring)
- Rework MSI initialization (Rob Herring)
- Move link handling into common code (Rob Herring)
- Move dw_pcie_msi_init() into core (Rob Herring)
- Move dw_pcie_setup_rc() to DWC common code (Rob Herring)
- Remove unnecessary wrappers around dw_pcie_host_init() (Rob
Herring)
- Drop keystone duplicated 'num-viewport'" (Rob Herring)
- Move inbound and outbound windows to common struct (Rob Herring)
- Detect number of iATU windows (Rob Herring)
- Warn if non-prefetchable memory aperture size is > 32-bit (Vidya
Sagar)
- Add support to program ATU for >4GB memory (Vidya Sagar)
- Set 32-bit DMA mask for MSI target address allocation (Vidya Sagar)
TI J721E PCIe driver:
- Fix "ti,syscon-pcie-ctrl" to take argument (Kishon Vijay Abraham I)
- Add host mode dt-bindings for TI's J7200 SoC (Kishon Vijay Abraham
I)
- Add EP mode dt-bindings for TI's J7200 SoC (Kishon Vijay Abraham I)
- Get offset within "syscon" from "ti,syscon-pcie-ctrl" phandle arg
(Kishon Vijay Abraham I)
TI Keystone PCIe controller driver:
- Enable compile-testing on !ARM (Alex Dewar)"
* tag 'pci-v5.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (100 commits)
PCI: Add function 1 DMA alias quirk for Marvell 9215 SATA controller
PCI/ACPI: Fix companion lookup for device 0 on the root bus
PCI: Keep both device and resource name for config space remaps
PCI: xgene: Removed unused ".bus_shift" initialisers from pci-xgene.c
PCI: vmd: Update type of the __iomem pointers
PCI: iproc: Convert to use the new ECAM constants
PCI: thunder-pem: Add constant for custom ".bus_shift" initialiser
PCI: Unify ECAM constants in native PCI Express drivers
PCI: Disable PTM during suspend to save power
PCI/PTM: Save/restore Precision Time Measurement Capability for suspend/resume
PCI: Mark AMD Raven iGPU ATS as broken in some platforms
PCI: j721e: Get offset within "syscon" from "ti,syscon-pcie-ctrl" phandle arg
dt-bindings: PCI: Add EP mode dt-bindings for TI's J7200 SoC
dt-bindings: PCI: Add host mode dt-bindings for TI's J7200 SoC
dt-bindings: pci: ti,j721e: Fix "ti,syscon-pcie-ctrl" to take argument
PCI: dwc: Set 32-bit DMA mask for MSI target address allocation
PCI: qcom: Add support for configuring BDF to SID mapping for SM8250
PCI: Reduce pci_set_cacheline_size() message to debug level
PCI: Remove unused HAVE_PCI_SET_MWI
PCI: qcom: Add SM8250 SoC support
...
- Support multiple ATU memory regions (Rob Herring)
- Warn if non-prefetchable memory aperture is > 32-bit (Vidya Sagar)
- Allow programming ATU for >4GB memory (Vidya Sagar)
- Move ATU offset out of driver match data (Rob Herring)
- Move "dbi", "dbi2", and "addr_space" resource setup to common code (Rob
Herring)
- Remove unneeded function wrappers (Rob Herring)
- Ensure all outbound ATU windows are reset to reduce dependencies on
bootloader (Rob Herring)
- Use the default MSI irq_chip for dra7xx (Rob Herring)
- Drop the .set_num_vectors() host op (Rob Herring)
- Move MSI interrupt setup into DWC common code (Rob Herring)
- Rework and simplify DWC MSI initialization (Rob Herring)
- Move link handling to DWC common code (Rob Herring)
- Move dw_pcie_msi_init() calls to DWC common code (Rob Herring)
- Move dw_pcie_setup_rc() calls to DWC common code (Rob Herring)
- Remove unnecessary wrappers around dw_pcie_host_init() (Rob Herring)
- Revert "keystone: Drop duplicated 'num-viewport'" to prepare for
detecting number of iATU regions without help from DT (Rob Herring)
- Move inbound and outbound windows to common struct (Rob Herring)
- Detect number of DWC iATU windows from device registers (Rob Herring)
- Drop samsung,exynos5440-pcie binding (Marek Szyprowski)
- Add samsung,exynos-pcie and samsung,exynos-pcie-phy bindings for
Exynos5433 variant (Marek Szyprowski)
- Rework phy-exynos-pcie driver to support Exynos5433 PCIe PHY (Jaehoon
Chung)
- Rework pci-exynos.c to support Exynos5433 PCIe host (Jaehoon Chung)
- Move tegra "dbi" accesses to post common DWC initialization (Vidya Sagar)
- Read tegra dbi" base address in application logic (Vidya Sagar)
- Fix tegra ASPM-L1SS advertisement disable code (Vidya Sagar)
- Set Tegra194 DesignWare IP version to 0x490A (Vidya Sagar)
- Continue tegra unconfig sequence even if parts fail (Vidya Sagar)
- Check return value of tegra_pcie_init_controller() (Vidya Sagar)
- Disable tegra LTSSM during L2 entry (Vidya Sagar)
- Add SM8250 SoC PCIe DT bindings and support (Manivannan Sadhasivam)
- Add SM8250 BDF to SID mapping (Manivannan Sadhasivam)
- Set 32-bit DMA mask for DWC MSI target address allocation (Vidya Sagar)
* remotes/lorenzo/pci/dwc:
PCI: dwc: Set 32-bit DMA mask for MSI target address allocation
PCI: qcom: Add support for configuring BDF to SID mapping for SM8250
PCI: qcom: Add SM8250 SoC support
dt-bindings: pci: qcom: Document PCIe bindings for SM8250 SoC
PCI: tegra: Disable LTSSM during L2 entry
PCI: tegra: Check return value of tegra_pcie_init_controller()
PCI: tegra: Continue unconfig sequence even if parts fail
PCI: tegra: Set DesignWare IP version
PCI: tegra: Fix ASPM-L1SS advertisement disable code
PCI: tegra: Read "dbi" base address to program in application logic
PCI: tegra: Move "dbi" accesses to post common DWC initialization
PCI: dwc: exynos: Rework the driver to support Exynos5433 variant
phy: samsung: phy-exynos-pcie: rework driver to support Exynos5433 PCIe PHY
dt-bindings: phy: exynos: add the samsung,exynos-pcie-phy binding
dt-bindings: PCI: exynos: add the samsung,exynos-pcie binding
dt-bindings: PCI: exynos: drop samsung,exynos5440-pcie binding
PCI: dwc: Detect number of iATU windows
PCI: dwc: Move inbound and outbound windows to common struct
Revert "PCI: dwc/keystone: Drop duplicated 'num-viewport'"
PCI: dwc: Remove unnecessary wrappers around dw_pcie_host_init()
PCI: dwc: Move dw_pcie_setup_rc() to DWC common code
PCI: dwc: Move dw_pcie_msi_init() into core
PCI: dwc: Move link handling into common code
PCI: dwc: Rework MSI initialization
PCI: dwc: Move MSI interrupt setup into DWC common code
PCI: dwc: Drop the .set_num_vectors() host op
PCI: dwc/dra7xx: Use the common MSI irq_chip
PCI: dwc: Ensure all outbound ATU windows are reset
PCI: dwc/intel-gw: Remove some unneeded function wrappers
PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code
PCI: dwc/intel-gw: Move ATU offset out of driver match data
PCI: dwc: Add support to program ATU for >4GB memory
PCI: of: Warn if non-prefetchable memory aperture size is > 32-bit
PCI: dwc: Support multiple ATU memory regions
- Make "cdns,max-outbound-regions" optional (Kishon Vijay Abraham I)
- Fix "ti,syscon-pcie-ctrl" DT property to take argument (Kishon Vijay
Abraham I)
- Add TI J7200 host and endpoint mode DT bindings (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/cadence:
PCI: j721e: Get offset within "syscon" from "ti,syscon-pcie-ctrl" phandle arg
dt-bindings: PCI: Add EP mode dt-bindings for TI's J7200 SoC
dt-bindings: PCI: Add host mode dt-bindings for TI's J7200 SoC
dt-bindings: pci: ti,j721e: Fix "ti,syscon-pcie-ctrl" to take argument
PCI: cadence: Do not error if "cdns,max-outbound-regions" is not found
dt-bindings: PCI: Make "cdns,max-outbound-regions" optional property
- Update comment about delay before link training (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Update comment about disabling link training
Going through a full irq descriptor lookup instead of just using the proper
helper function which provides direct access is suboptimal.
In fact it _is_ wrong because the chip callback needs to get the chip data
which is relevant for the chip while using the irq descriptor variant
returns the irq chip data of the top level chip of a hierarchy. It does not
matter in this case because the chip is the top level chip, but that
doesn't make it more correct.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201210194044.473308721@linutronix.de
Going through a full irq descriptor lookup instead of just using the proper
helper function which provides direct access is suboptimal.
In fact it _is_ wrong because the chip callback needs to get the chip data
which is relevant for the chip while using the irq descriptor variant
returns the irq chip data of the top level chip of a hierarchy. It does not
matter in this case because the chip is the top level chip, but that
doesn't make it more correct.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201210194044.364211860@linutronix.de
- Simplification and distangling of the MSI related functionality
- Let IO/APIC construct the RTE entries from an MSI message instead of
having IO/APIC specific code in the interrupt remapping drivers
- Make the retrieval of the parent interrupt domain (vector or remap
unit) less hardcoded and use the relevant irqdomain callbacks for
selection.
- Allow the handling of more than 255 CPUs without a virtualized IOMMU
when the hypervisor supports it. This has made been possible by the
above modifications and also simplifies the existing workaround in the
HyperV specific virtual IOMMU.
- Cleanup of the historical timer_works() irq flags related
inconsistencies.
-----BEGIN PGP SIGNATURE-----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=8Gfs
-----END PGP SIGNATURE-----
Merge tag 'x86-apic-2020-12-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 apic updates from Thomas Gleixner:
"Yet another large set of x86 interrupt management updates:
- Simplification and distangling of the MSI related functionality
- Let IO/APIC construct the RTE entries from an MSI message instead
of having IO/APIC specific code in the interrupt remapping drivers
- Make the retrieval of the parent interrupt domain (vector or remap
unit) less hardcoded and use the relevant irqdomain callbacks for
selection.
- Allow the handling of more than 255 CPUs without a virtualized
IOMMU when the hypervisor supports it. This has made been possible
by the above modifications and also simplifies the existing
workaround in the HyperV specific virtual IOMMU.
- Cleanup of the historical timer_works() irq flags related
inconsistencies"
* tag 'x86-apic-2020-12-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (42 commits)
x86/ioapic: Cleanup the timer_works() irqflags mess
iommu/hyper-v: Remove I/O-APIC ID check from hyperv_irq_remapping_select()
iommu/amd: Fix IOMMU interrupt generation in X2APIC mode
iommu/amd: Don't register interrupt remapping irqdomain when IR is disabled
iommu/amd: Fix union of bitfields in intcapxt support
x86/ioapic: Correct the PCI/ISA trigger type selection
x86/ioapic: Use I/O-APIC ID for finding irqdomain, not index
x86/hyperv: Enable 15-bit APIC ID if the hypervisor supports it
x86/kvm: Enable 15-bit extension when KVM_FEATURE_MSI_EXT_DEST_ID detected
iommu/hyper-v: Disable IRQ pseudo-remapping if 15 bit APIC IDs are available
x86/apic: Support 15 bits of APIC ID in MSI where available
x86/ioapic: Handle Extended Destination ID field in RTE
iommu/vt-d: Simplify intel_irq_remapping_select()
x86: Kill all traces of irq_remapping_get_irq_domain()
x86/ioapic: Use irq_find_matching_fwspec() to find remapping irqdomain
x86/hpet: Use irq_find_matching_fwspec() to find remapping irqdomain
iommu/hyper-v: Implement select() method on remapping irqdomain
iommu/vt-d: Implement select() method on remapping irqdomain
iommu/amd: Implement select() method on remapping irqdomain
x86/apic: Add select() method on vector irqdomain
...
Removed unused ".bus_shift" initialisers from pci-xgene.c as
xgene_pcie_map_bus() did not use these.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201129230743.3006978-6-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use "void __iomem" instead "char __iomem" pointer type when working with
the accessor functions (with names like readb() or writel(), etc.) to
better match a given accessor function signature where commonly the address
pointing to an I/O memory region would be a "void __iomem" pointer.
Related: https://lwn.net/Articles/102232/
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201129230743.3006978-5-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Change interface of the function iproc_pcie_map_ep_cfg_reg() so that use
of PCI_SLOT() and PCI_FUNC() macros and most of the local ECAM-specific
constants can be dropped, and the new PCIE_ECAM_OFFSET() macro can be
used instead. Use the ALIGN_DOWN() macro to ensure that PCI Express
ECAM offset is always 32 bit aligned.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201129230743.3006978-4-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a custom constant for the ".bus_shift" initialiser to capture a
non-standard platform-specific ECAM bus shift value.
Standard values otherwise defined in the PCI Express Specification are
available in the include/linux/pci-ecam.h.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201129230743.3006978-3-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add ECAM-related constants to provide a set of standard constants
defining memory address shift values to the byte-level address that can
be used to access the PCI Express Configuration Space, and then move
native PCI Express controller drivers to use the newly introduced
definitions retiring driver-specific ones.
Refactor pci_ecam_map_bus() function to use newly added constants so
that limits to the bus, device function and offset (now limited to 4K as
per the specification) are in place to prevent the defective or
malicious caller from supplying incorrect configuration offset and thus
targeting the wrong device when accessing extended configuration space.
This refactor also allows for the ".bus_shift" initialisers to be
dropped when the user is not using a custom value as a default value
will be used as per the PCI Express Specification.
Thanks to Qian Cai <qcai@redhat.com>, Michael Walle <michael@walle.cc>,
and Vladimir Oltean <olteanv@gmail.com> for reporting a pci_ecam_create()
issue with .bus_shift and to Vladimir for proposing the fix.
[bhelgaas: incorporate Vladimir's fix, update commit log]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201129230743.3006978-2-kw@linux.com
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Get "syscon" pcie_ctrl offset from the argument of "ti,syscon-pcie-ctrl"
phandle. Previously a subnode to "syscon" node was added which has the
exact memory mapped address of pcie_ctrl but now the offset of pcie_ctrl
within "syscon" is now being passed as argument to "ti,syscon-pcie-ctrl"
phandle.
If the offset is not provided in "ti,syscon-pcie-ctrl", the
full memory mapped address of pcie_ctrl is used in order to maintain old
DT compatibility.
This change is as discussed in [1]
[1] -> http://lore.kernel.org/r/CAL_JsqKiUcO76bo1GoepWM1TusJWoty_BRy2hFSgtEVMqtrvvQ@mail.gmail.com
Link: https://lore.kernel.org/r/20201210124917.24185-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Set DMA mask to 32-bit while allocating the MSI target address so that
the address is usable for both 32-bit and 64-bit MSI capable devices.
Throw a warning if it fails to set the mask to 32-bit to alert that
devices that are only 32-bit MSI capable may not work properly.
Link: https://lore.kernel.org/r/20201117165312.25847-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
For SM8250, we need to write the BDF to SID mapping in PCIe controller
register space for proper working. This is accomplished by extracting
the BDF and SID values from "iommu-map" property in DT and writing those
in the register address calculated from the hash value of BDF. In case
of collisions, the index of the next entry will also be written.
For the sake of it, let's introduce a "config_sid" callback and do it
conditionally for SM8250.
Link: https://lore.kernel.org/r/20201208121402.178011-4-mani@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The PCIe IP (rev 1.9.0) on SM8250 SoC is similar to the one used on
SDM845. Hence the support is added reusing the members of ops_2_7_0.
The key difference between ops_2_7_0 and ops_1_9_0 is the config_sid
callback, which will be added in successive commit.
Link: https://lore.kernel.org/r/20201208121402.178011-3-mani@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
PCIe cards like Marvell SATA controller and some of the Samsung NVMe
drives don't support taking the link to L2 state. When the link doesn't
go to L2 state, Tegra194 requires the LTSSM to be disabled to allow PHY
to start the next link up process cleanly during suspend/resume sequence.
Failing to disable LTSSM results in the PCIe link not coming up in the
next resume cycle.
Link: https://lore.kernel.org/r/20201203133451.17716-6-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The return value of tegra_pcie_init_controller() must be checked before
PCIe link up check and registering debugfs entries subsequently as it
doesn't make sense to do these when the controller initialization itself
has failed.
Link: https://lore.kernel.org/r/20201203133451.17716-5-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Currently the driver checks for error value of different APIs during the
uninitialization sequence. It just returns from there if there is any error
observed for one of those calls. Comparatively it is better to continue the
uninitialization sequence irrespective of whether some of them are
returning error. That way, it is more closer to complete uninitialization.
Link: https://lore.kernel.org/r/20201203133451.17716-4-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Set the DesignWare IP version for Tegra194 to 0x490A. This would be used
by the DesigWare sub-system to do any version specific configuration
(Ex:- TD bit programming for ECRC).
Link: https://lore.kernel.org/r/20201203133451.17716-3-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
If the absence of CLKREQ# signal is indicated by the absence of
"supports-clkreq" in the device-tree node, current driver is disabling
the advertisement of ASPM-L1 Sub-States *before* the ASPM-L1 Sub-States
offset is correctly initialized. Since default value of the ASPM-L1SS
offset is zero, this is causing the Vendor-ID wrongly programmed to 0x10d2
instead of Nvidia's 0x10de thereby the quirks applicable for Tegra194 are
not being applied. This patch fixes this issue by refactoring the
code that disables the ASPM-L1SS advertisement.
Link: https://lore.kernel.org/r/20201203133451.17716-2-vidyas@nvidia.com
Fixes: 56e15a238d ("PCI: tegra: Add Tegra194 PCIe support")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
According to PCI Express Base Specifications (rev 4.0, 6.6.1
"Conventional reset"), after fundamental reset a 100ms delay is needed
prior to enabling link training.
Update comment in code to reflect this requirement.
Link: https://lore.kernel.org/r/20201202184659.3795-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PCIe controller in Tegra194 requires the "dbi" region base address to be
programmed in one of the application logic registers to enable CPU access
to the "dbi" region. But, commit a0fd361db8 ("PCI: dwc: Move "dbi",
"dbi2", and "addr_space" resource setup into common code") moved the code
that reads the whereabouts of "dbi" region to the common code causing the
existing code in pcie-tegra194.c file to program NULL in the application
logic registers. This is causing null pointer dereference when the "dbi"
registers are accessed. This issue is fixed by explicitly reading the
"dbi" base address from DT node.
Link: https://lore.kernel.org/r/20201125192554.5401-1-vidyas@nvidia.com
Fixes: a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code")
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
commit a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space"
resource setup into common code") moved the code that sets up dbi_base
to DWC common code thereby creating a requirement to not access the "dbi"
region before calling common DWC initialization code. But, Tegra194
already had some code that programs some of the "dbi" registers resulting
in system crash. This patch addresses that issue by refactoring the code
to have accesses to the "dbi" region only after common DWC initialization.
Link: https://lore.kernel.org/r/20201125192234.2270-1-vidyas@nvidia.com
Fixes: a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code")
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Exynos5440 SoC support has been dropped since commit 8c83315da1 ("ARM:
dts: exynos: Remove Exynos5440"). Rework this driver to support DWC PCIe
variant found in the Exynos5433 SoCs.
The main difference in Exynos5433 variant is lack of the MSI support
(the MSI interrupt is not even routed to the CPU).
[mszyprow: reworked the driver to support only Exynos5433 variant,
simplified code, rebased onto current kernel code, added
regulator support, converted to the regular platform driver,
removed MSI related code, rewrote commit message, added help]
Link: https://lore.kernel.org/r/20201113170139.29956-6-m.szyprowski@samsung.com
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Add logging code so that after successful linkup more comprehensive
information about PCIe link speed and link width will be displayed to
the console.
Link: https://lore.kernel.org/r/20201001060054.6616-4-srinath.mannam@broadcom.com
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Second stage bootloaders prior to Linux boot may use all inbound windows
including IARR1/IMAP1. We need to ensure that all previous configuration
of inbound windows are invalidated during the initialization stage of
the Linux iProc PCIe driver so let's add a fix to define and invalidate
IARR1/IMAP1 because it is currently missing, fixing the issue.
Link: https://lore.kernel.org/r/20201001060054.6616-3-srinath.mannam@broadcom.com
Fixes: 9415743e4c ("PCI: iproc: Invalidate PAXB address mapping")
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Declare the full size array for all revisions of PAX register sets
to avoid potentially out of bound access of the register array
when they are being initialized in iproc_pcie_rev_init().
Link: https://lore.kernel.org/r/20201001060054.6616-2-srinath.mannam@broadcom.com
Fixes: 06324ede76 ("PCI: iproc: Improve core register population")
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Client VMD platforms have a software-triggered MSI-X vector 0 that will
not forward hardware-remapped MSI from the sub-device domain. This
causes an issue with VMD platforms that use AHCI behind VMD and have a
single MSI-X vector remapped to VMD vector 0. Add a VMD MSI-X vector
offset for these platforms.
Link: https://lore.kernel.org/r/20201102222223.92978-1-jonathan.derrick@intel.com
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The variable 'tmp' is used multiple times in the brcm_pcie_setup()
function. One such usage did not initialize 'tmp' to the current value
of the target register. By luck the mistake does not currently affect
behavior; regardless 'tmp' is now initialized properly.
Suggested-by: Rafał Miłecki <zajec5@gmail.com>
Link: https://lore.kernel.org/r/20201102205712.23332-1-james.quinlan@broadcom.com
Fixes: c045213703 ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Drop unused members dev and base from struct rcar_pcie_host.
Link: https://lore.kernel.org/r/20201023162008.967-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the number of inbound and outbound iATU windows are determined
from DT properties. Unfortunately, there's 'num-viewport' for RC mode
and 'num-ib-windows' and 'num-ob-windows' for EP mode, yet the number of
windows is not mode dependent. Also, 'num-viewport' is not clear whether
that's inbound, outbound or both. We can probably assume it's outbound
windows as that's all RC mode uses.
However, using DT properties isn't really needed as the number of
regions can be detected at runtime by poking the iATU registers. The
basic algorithm is just writing a target address and reading back what
we wrote. In the unrolled ATU case, we have to take care not to go
past the mapped region.
With this, we can drop num_viewport in favor of num_ob_windows instead.
Link: https://lore.kernel.org/r/20201105211159.1814485-17-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
The number of inbound and outbound windows are defined by the h/w and
apply to both RC and EP modes, so move them to the appropriate struct.
Link: https://lore.kernel.org/r/20201105211159.1814485-16-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit 421063efaf.
In preparation to detect the number of iATU regions instead of using DT
properties, we need to keep reading 'num-viewport' for the Keystone
driver which doesn't use the iATU in older versions of the IP.
However, note that Keystone has been broken for some time with upstream
dts files which don't set 'num-viewports'. The reverted commit did
make the property optional, but now it's mandatory again.
Link: https://lore.kernel.org/r/20201105211159.1814485-15-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Many calls to dw_pcie_host_init() are in a wrapper function with
nothing else now. Let's remove the pointless extra layer.
Link: https://lore.kernel.org/r/20201105211159.1814485-14-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
All RC complex drivers must call dw_pcie_setup_rc(). The ordering of the
call shouldn't be too important other than being after any RC resets.
There's a few calls of dw_pcie_setup_rc() left as drivers implementing
suspend/resume need it.
Link: https://lore.kernel.org/r/20201105211159.1814485-13-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
All the DWC drivers do link setup and checks at roughly the same time.
Let's use the existing .start_link() hook (currently only used in EP
mode) and move the link handling to the core code.
The behavior for a link down was inconsistent as some drivers would fail
probe in that case while others succeed. Let's standardize this to
succeed as there are usecases where devices (and the link) appear later
even without hotplug. For example, a reconfigured FPGA device.
Link: https://lore.kernel.org/r/20201105211159.1814485-11-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
There are 3 possible MSI implementations for the DWC host. The first is
using the built-in DWC MSI controller. The 2nd is a custom MSI
controller as part of the PCI host (keystone only). The 3rd is an
external MSI controller (typically GICv3 ITS). Currently, the last 2
are distinguished with a .msi_host_init() hook with the 3rd option using
an empty function. However we can detect the 3rd case with the presence
of 'msi-parent' or 'msi-map' properties, so let's do that instead and
remove the empty functions.
Link: https://lore.kernel.org/r/20201105211159.1814485-10-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: linuxppc-dev@lists.ozlabs.org
Platforms using the built-in DWC MSI controller all have a dedicated
interrupt with "msi" name or at index 0, so let's move setting up the
interrupt to the common DWC code.
spear13xx and dra7xx are the 2 oddballs with muxed interrupts, so
we need to prevent configuring the MSI interrupt by setting msi_irq
to negative.
Link: https://lore.kernel.org/r/20201105211159.1814485-9-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
There's no reason for the .set_num_vectors() host op. Drivers needing a
non-default value can just initialize pcie_port.num_vectors directly.
Link: https://lore.kernel.org/r/20201105211159.1814485-8-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
The dra7xx MSI irq_chip implementation is identical to the default DWC one.
The only difference is the interrupt handler as the MSI interrupt is muxed
with other interrupts, but that doesn't affect the irq_chip part of it.
Link: https://lore.kernel.org/r/20201105211159.1814485-7-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-omap@vger.kernel.org
The Layerscape driver clears the ATU registers which may have been
configured by the bootloader. Any driver could have the same issue
and doing it for all drivers doesn't hurt, so let's move it into the
common DWC code.
Link: https://lore.kernel.org/r/20201105211159.1814485-6-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: linuxppc-dev@lists.ozlabs.org
Remove some of the pointless levels of functions that just wrap or group
a series of other functions.
Link: https://lore.kernel.org/r/20201105211159.1814485-5-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Most DWC drivers use the common register resource names "dbi", "dbi2", and
"addr_space", so let's move their setup into the DWC common code.
This means 'dbi_base' in particular is setup later, but it looks like no
drivers touch DBI registers before dw_pcie_host_init or dw_pcie_ep_init.
Link: https://lore.kernel.org/r/20201105211159.1814485-4-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-omap@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
The ATU offset should be a register range in DT called 'atu', not driver
match data. Any future platforms with a different ATU offset should add
it to their DT.
This is also in preparation to do DBI resource setup in the core DWC
code, so let's move setting atu_base later in intel_pcie_rc_setup().
Link: https://lore.kernel.org/r/20201105211159.1814485-3-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Currently the Keystone driver can only be compile-tested on ARM, but
this restriction seems unnecessary. Get rid of it to increase test
coverage.
Build-tested with allyesconfig on x86, ppc, mips and riscv.
Link: https://lore.kernel.org/r/20200906195128.279342-1-alex.dewar90@gmail.com
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Add support to program the ATU to enable translations for >4GB sizes of
the prefetchable memory apertures.
Link: https://lore.kernel.org/r/20201118144626.32189-3-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jingoo <jingoohan1@gmail.com>
The current ATU setup only supports a single memory resource which
isn't sufficient if there are also prefetchable memory regions. In order
to support multiple memory regions, we need to move away from fixed ATU
slots and rework the assignment. As there's always an ATU entry for
config space, let's assign index 0 to config space. Then we assign
memory resources to index 1 and up. Finally, if we have an I/O region
and slots remaining, we assign the I/O region last. If there aren't
remaining slots, we keep the same config and I/O space sharing.
Link: https://lore.kernel.org/r/20201026181652.418729-1-robh@kernel.org
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
With commit 669cbc7081 ("PCI: Move DT resource setup into
devm_pci_alloc_host_bridge()"), the DT 'ranges' is parsed and populated
into resources when the host bridge is allocated. The resources are
requested as well, but that happens a second time for the mvebu driver in
mvebu_pcie_parse_request_resources(). We should only be requesting the
additional resources added in mvebu_pcie_parse_request_resources(). These
are not added by default because they use custom properties rather than
standard DT address translation.
Also, the bus ranges was also populated by default, so we can remove it
from mvebu_pci_host_probe().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=209729
Fixes: 669cbc7081 ("PCI: Move DT resource setup into devm_pci_alloc_host_bridge()")
Link: https://lore.kernel.org/r/20201023145252.2691779-1-robh@kernel.org
Reported-by: vtolkm@googlemail.com
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Russell King <linux@armlinux.org.uk>
Prior to commit 0f71c60ffd ("PCI: dwc: Remove storing of PCI resources"),
the DWC driver was setting up the last memory resource rather than the
first memory resource. This doesn't matter for most platforms which only
have 1 memory resource, but it broke Tegra194 which has a 2nd
(prefetchable) memory region that requires an ATU entry. The first region
on Tegra194 relies on the default 1:1 pass-thru of outbound transactions
and doesn't need an ATU entry.
Fixes: 0f71c60ffd ("PCI: dwc: Remove storing of PCI resources")
Link: https://lore.kernel.org/r/20201026154852.221483-1-robh@kernel.org
Reported-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Use the x86 shadow structs in msi_msg instead of the macros.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201024213535.443185-16-dwmw2@infradead.org
The enum ioapic_irq_destination_types and the enumerated constants starting
with 'dest_' are gross misnomers because they describe the delivery mode.
Rename then enum and the constants so they actually make sense.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201024213535.443185-6-dwmw2@infradead.org
- Drop return value checking for debugfs_create() calls (Greg
Kroah-Hartman)
- Convert debugfs "ports" file to use DEFINE_SEQ_ATTRIBUTE() (Liu Shixin)
* remotes/lorenzo/pci/tegra:
PCI: tegra: Convert to use DEFINE_SEQ_ATTRIBUTE macro
PCI: tegra: No need to check return value of debugfs_create() functions
- Document R8A774A1, R8A774B1, R8A774E1 endpoint support in DT (Lad
Prabhakar)
- Add R8A774A1, R8A774B1, R8A774E1 (RZ/G2M, RZ/G2N, RZ/G2H) IDs to endpoint
test (Lad Prabhakar)
- Add device tree support for R8A7742 (Lad Prabhakar)
- Use "fallthrough" pseudo-keyword (Gustavo A. R. Silva)
* remotes/lorenzo/pci/rcar:
dt-bindings: PCI: rcar: Add device tree support for r8a7742
PCI: rcar-gen2: Use fallthrough pseudo-keyword
misc: pci_endpoint_test: Add Device ID for RZ/G2H PCIe controller
dt-bindings: pci: rcar-pci-ep: Document r8a774e1
misc: pci_endpoint_test: Add Device ID for RZ/G2M and RZ/G2N PCIe controllers
dt-bindings: pci: rcar-pci-ep: Document r8a774a1 and r8a774b1
- Make sure PCIe is reset before init to work around QSDK U-Boot issue
(Ansuel Smith)
- Set iproc affinity mask on MSI interrupts (Mark Tomlinson)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Make sure PCIe is reset before init for rev 2.1.0
- Return -EPROBE_DEFER in case the gpio isn't ready (Bean Huo)
* remotes/lorenzo/pci/kirin:
PCI: kirin: Return -EPROBE_DEFER in case the gpio isn't ready
- Set affinity mask on MSI interrupts (Mark Tomlinson)
- Simplify by using module_bcma_driver (Liu Shixin)
- Fix 'using integer as NULL pointer' warning (Krzysztof Wilczyński)
* remotes/lorenzo/pci/iproc:
PCI: iproc: Fix using plain integer as NULL pointer in iproc_pcie_pltfm_probe
PCI: iproc: Use module_bcma_driver to simplify the code
PCI: iproc: Set affinity mask on MSI interrupts
- Use "fallthrough" pseudo-keyword (Gustavo A. R. Silva)
- Drop redundant error messages after devm_clk_get() (Anson Huang)
* remotes/lorenzo/pci/imx6:
PCI: imx6: Do not output error message when devm_clk_get() failed with -EPROBE_DEFER
PCI: imx6: Use fallthrough pseudo-keyword
- Fix hibernation in case interrupts are not re-created (Dexuan Cui)
* remotes/lorenzo/pci/hv:
PCI: hv: Fix hibernation in case interrupts are not re-created
- Fix designware-ep Header Type check (Hou Zhiqiang)
- Use DBI accessors instead of own config accessors (Rob Herring)
- Allow overriding bridge pci_ops (Rob Herring)
- Allow root and child buses to have different pci_ops (Rob Herring)
- Add default dwc pci_ops.map_bus (Rob Herring)
- Use pci_ops for root config space accessors in al, exynos, histb,
keystone, kirin, meson, tegra (Rob Herring)
- Remove dwc own/other config accessor ops (Rob Herring)
- Use generic config accessors in dwc (Rob Herring)
- Also call .add_bus() callback for root bus (Rob Herring)
- Convert keystone .scan_bus() callback to use pci_ops.add_bus (Rob
Herring)
- Convert dwc to use pci_host_probe() (Rob Herring)
- Remove dwc root_bus pointer (Rob Herring)
- Remove storing of PCI resources in dwc-specific structs (Rob Herring)
- Simplify config space handling (Rob Herring)
- Drop keystone duplicated DT num-viewport handling (Rob Herring)
- Check CONFIG_PCI_MSI in dw_pcie_msi_init() instead of duplicating it in
all the drivers (Rob Herring)
- Remove imx6 duplicate PCIE_LINK_WIDTH_SPEED_CONTROL definition (Rob
Herring)
- Add dwc num_lanes for use when it's lacking from DT (Rob Herring)
- Ensure "Fast Link Mode" simulation environment setting is cleared (Rob
Herring)
- Drop meson duplicate number of lanes setup (Rob Herring)
- Drop meson unnecessary RC config space init (Rob Herring)
- Rework meson config and dwc port logic register accesses (Rob Herring)
- Use common PCI register definitions in imx6 and qcom (Rob Herring)
- Search for DesignWare PCIe Capability instead of hard-coding its location
(Rob Herring)
- Use common DesignWare register definitions in tegra (Rob Herring)
- Drop keystone unused DBI2 code (Rob Herring)
- Make dwc ATU accessors private (Rob Herring)
- Centralize link gen setting in dwc (Rob Herring)
- Set PORT_LINK_DLL_LINK_EN in common dwc setup code (Rob Herring)
- Drop intel-gw unnecessary DT 'device_type' checking (Rob Herring)
- Move intel-gw PCI_CAP_ID_EXP discovery to the single place it's used (Rob
Herring)
- Drop intel-gw unused max_width (Rob Herring)
- Move N_FTS (fast training sequence) setup to common dwc setup (Rob
Herring)
- Convert spear13xx, tegra194 to use DBI accessors (Rob Herring)
- Add multiple PFs support for DWC (Xiaowei Bao)
- Add MSI-X doorbell mode for endpoint mode (Xiaowei Bao)
- Update MSI/MSI-X capability management for endpoints (Xiaowei Bao)
- Add layerscape ls1088a and ls2088a compatible strings (Xiaowei Bao)
- Update layerscape MSI/MSI-X management (Xiaowei Bao)
- Use doorbell to support MSI-X on layerscape (Xiaowei Bao)
- Add layerscape endpoint mode support for ls1088a and ls2088a (Xiaowei
Bao)
- Add layerscape ls1088a node to DT (Xiaowei Bao)
- Add Freescale/Layerscape ls1088a to endpoint test (Xiaowei Bao)
- Add endpoint test driver data for Layerscape PCIe controllers (Hou
Zhiqiang)
- Fix 'cast truncates bits from constant value' warning (Gustavo Pimentel)
- Add uniphier iATU register description (Kunihiko Hayashi)
- Add common iATU register support (Kunihiko Hayashi)
- Remove keystone iATU register mapping in favor of generic dwc support
(Kunihiko Hayashi)
- Skip PCIE_MSI_INTR0* programming if MSI is disabled (Jisheng Zhang)
- Fix MSI page leakage in suspend/resume (Jisheng Zhang)
- Check whether link is up before attempting config access (best-effort fix
even though it's racy) (Hou Zhiqiang)
* remotes/lorenzo/pci/dwc:
PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()
PCI: dwc: Fix MSI page leakage in suspend/resume
PCI: dwc: Skip PCIE_MSI_INTR0* programming if MSI is disabled
PCI: keystone: Remove iATU register mapping
PCI: dwc: Add common iATU register support
dt-bindings: PCI: uniphier-ep: Add iATU register description
dt-bindings: PCI: uniphier: Add iATU register description
PCI: dwc: Fix 'cast truncates bits from constant value'
misc: pci_endpoint_test: Add driver data for Layerscape PCIe controllers
misc: pci_endpoint_test: Add LS1088a in pci_device_id table
PCI: layerscape: Add EP mode support for ls1088a and ls2088a
PCI: layerscape: Modify the MSIX to the doorbell mode
PCI: layerscape: Modify the way of getting capability with different PEX
PCI: layerscape: Fix some format issue of the code
dt-bindings: pci: layerscape-pci: Add compatible strings for ls1088a and ls2088a
PCI: designware-ep: Modify MSI and MSIX CAP way of finding
PCI: designware-ep: Move the function of getting MSI capability forward
PCI: designware-ep: Add the doorbell mode of MSI-X in EP mode
PCI: designware-ep: Add multiple PFs support for DWC
PCI: dwc: Use DBI accessors
PCI: dwc: Move N_FTS setup to common setup
PCI: dwc/intel-gw: Drop unused max_width
PCI: dwc/intel-gw: Move getting PCI_CAP_ID_EXP offset to intel_pcie_link_setup()
PCI: dwc/intel-gw: Drop unnecessary checking of DT 'device_type' property
PCI: dwc: Set PORT_LINK_DLL_LINK_EN in common setup code
PCI: dwc: Centralize link gen setting
PCI: dwc: Make ATU accessors private
PCI: dwc: Remove read_dbi2 code
PCI: dwc/tegra: Use common Designware port logic register definitions
PCI: dwc: Remove hardcoded PCI_CAP_ID_EXP offset
PCI: dwc/qcom: Use common PCI register definitions
PCI: dwc/imx6: Use common PCI register definitions
PCI: dwc/meson: Rework PCI config and DW port logic register accesses
PCI: dwc/meson: Drop unnecessary RC config space initialization
PCI: dwc/meson: Drop the duplicate number of lanes setup
PCI: dwc: Ensure FAST_LINK_MODE is cleared
PCI: dwc: Add a 'num_lanes' field to struct dw_pcie
PCI: dwc/imx6: Remove duplicate define PCIE_LINK_WIDTH_SPEED_CONTROL
PCI: dwc: Check CONFIG_PCI_MSI inside dw_pcie_msi_init()
PCI: dwc/keystone: Drop duplicated 'num-viewport'
PCI: dwc: Simplify config space handling
PCI: dwc: Remove storing of PCI resources
PCI: dwc: Remove root_bus pointer
PCI: dwc: Convert to use pci_host_probe()
PCI: dwc: keystone: Convert .scan_bus() callback to use add_bus
PCI: Also call .add_bus() callback for root bus
PCI: dwc: Use generic config accessors
PCI: dwc: Remove dwc specific config accessor ops
PCI: dwc: histb: Use pci_ops for root config space accessors
PCI: dwc: exynos: Use pci_ops for root config space accessors
PCI: dwc: kirin: Use pci_ops for root config space accessors
PCI: dwc: meson: Use pci_ops for root config space accessors
PCI: dwc: tegra: Use pci_ops for root config space accessors
PCI: dwc: keystone: Use pci_ops for config space accessors
PCI: dwc: al: Use pci_ops for child config space accessors
PCI: dwc: Add a default pci_ops.map_bus for root port
PCI: dwc: Allow overriding bridge pci_ops
PCI: dwc: Use DBI accessors instead of own config accessors
PCI: Allow root and child buses to have different pci_ops
PCI: designware-ep: Fix the Header Type check
- Make PCIE_BRCMSTB depend on and default to ARCH_BRCMSTB (Jim Quinlan)
- Add DT bindings for 7278, 7216, 7211, and new properties (Jim Quinlan)
- Add bcm7278 register info (Jim Quinlan)
- Add suspend and resume pm_ops (Jim Quinlan)
- Add bcm7278 PERST# support (Jim Quinlan)
- Add control of RESCAL reset (Jim Quinlan)
- Set additional internal memory DMA viewport sizes (Jim Quinlan)
- Accommodate MSI for older chips (Jim Quinlan)
- Set bus max burst size by chip type (Jim Quinlan)
- Add bcm7211, bcm7216, bcm7445, bcm7278 to match list (Jim Quinlan)
* remotes/lorenzo/pci/brcmstb:
PCI: brcmstb: Add bcm7211, bcm7216, bcm7445, bcm7278 to match list
PCI: brcmstb: Set bus max burst size by chip type
PCI: brcmstb: Accommodate MSI for older chips
PCI: brcmstb: Set additional internal memory DMA viewport sizes
PCI: brcmstb: Add control of rescal reset
PCI: brcmstb: Add bcm7278 PERST# support
PCI: brcmstb: Add suspend and resume pm_ops
PCI: brcmstb: Add bcm7278 register info
dt-bindings: PCI: Add bindings for more Brcmstb chips
PCI: brcmstb: PCIE_BRCMSTB depends on ARCH_BRCMSTB
The pci_save_state() call in vmd_suspend() can be performed by
pci_pm_suspend_irq(). This also allows VMD to benefit from the call into
pci_prepare_to_sleep().
The pci_restore_state() call in vmd_resume() was restoring state after
pci_pm_resume()::pci_restore_standard_config() had already restored state.
It's also been suspected that the config state should have been restored
before re-requesting IRQs instead of afterwards.
Remove the pci_save_state()/pci_restore_state() calls in
vmd_suspend()/vmd_resume() to allow proper flow through generic PCI core
Power Management code.
Link: https://lore.kernel.org/r/20200806210017.5654-1-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: You-Sheng Yang <vicamo.yang@canonical.com>
Move the IRQ allocation and SRCU initialization code to a new helper. No
functional changes.
Link: https://lore.kernel.org/r/20200728194945.14126-5-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Move the IRQ and MSI Domain configuration code to new helpers. No
functional changes.
Link: https://lore.kernel.org/r/20200728194945.14126-4-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Move the bus offset configuration discovery code to a new helper. Modify
the bus offset 2-bit decode switch to have a 0 case and a default error
case, just in case the field is expanded in future hardware.
Link: https://lore.kernel.org/r/20200728194945.14126-3-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Move the guest-passthrough physical offset discovery code to a new helper.
No functional changes.
Link: https://lore.kernel.org/r/20200728194945.14126-2-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
A break is not needed if it is preceded by a return
Link: https://lore.kernel.org/r/20201019190249.7825-1-trix@redhat.com
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
NXP Layerscape (ls1028a, ls2088a), dra7xxx and imx6 platforms are either
programmed or statically configured to forward the error triggered by a
link-down state (eg no connected endpoint device) on the system bus for
PCI configuration transactions; these errors are reported as an SError
at system level, which is fatal.
Enumerating a PCI tree when the PCIe link is down is not sensible
either, so even if the link-up check is racy (link can go down after
map_bus() is called) add a link-up check in map_bus() to prevent issuing
configuration transactions when the link is down.
SError report:
SError Interrupt on CPU2, code 0xbf000002 -- SError
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.9.0-rc5-next-20200914-00001-gf965d3ec86fa #67
Hardware name: LS1046A RDB Board (DT)
pstate: 20000085 (nzCv daIf -PAN -UAO BTYPE=--)
pc : pci_generic_config_read+0x3c/0xe0
lr : pci_generic_config_read+0x24/0xe0
sp : ffff80001003b7b0
x29: ffff80001003b7b0 x28: ffff80001003ba74
x27: ffff000971d96800 x26: ffff00096e77e0a8
x25: ffff80001003b874 x24: ffff80001003b924
x23: 0000000000000004 x22: 0000000000000000
x21: 0000000000000000 x20: ffff80001003b874
x19: 0000000000000004 x18: ffffffffffffffff
x17: 00000000000000c0 x16: fffffe0025981840
x15: ffffb94c75b69948 x14: 62203a383634203a
x13: 666e6f635f726568 x12: 202c31203d207265
x11: 626d756e3e2d7375 x10: 656877202c307830
x9 : 203d206e66766564 x8 : 0000000000000908
x7 : 0000000000000908 x6 : ffff800010900000
x5 : ffff00096e77e080 x4 : 0000000000000000
x3 : 0000000000000003 x2 : 84fa3440ff7e7000
x1 : 0000000000000000 x0 : ffff800010034000
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.9.0-rc5-next-20200914-00001-gf965d3ec86fa #67
Hardware name: LS1046A RDB Board (DT)
Call trace:
dump_backtrace+0x0/0x1c0
show_stack+0x18/0x28
dump_stack+0xd8/0x134
panic+0x180/0x398
add_taint+0x0/0xb0
arm64_serror_panic+0x78/0x88
do_serror+0x68/0x180
el1_error+0x84/0x100
pci_generic_config_read+0x3c/0xe0
dw_pcie_rd_other_conf+0x78/0x110
pci_bus_read_config_dword+0x88/0xe8
pci_bus_generic_read_dev_vendor_id+0x30/0x1b0
pci_bus_read_dev_vendor_id+0x4c/0x78
pci_scan_single_device+0x80/0x100
Link: https://lore.kernel.org/r/20200916054130.8685-1-Zhiqiang.Hou@nxp.com
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: rewrote the commit log, remove Fixes tag]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get
wrong, as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception of
the last "obviously correct" patch that updated a FALLTHROUGH comment
that got merged last weekend.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4hAAg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfRACcCp48StLg4V7XcZ41eQYES/DVwxkAnjnZs+La
Y7F+o2p8DiuLLQamdEyB
=lHr1
-----END PGP SIGNATURE-----
Merge tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY/Thunderbolt driver updates from Greg KH:
"Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get wrong,
as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception
of the last "obviously correct" patch that updated a FALLTHROUGH
comment that got merged last weekend"
* tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (374 commits)
usb: musb: gadget: Use fallthrough pseudo-keyword
usb: typec: Add QCOM PMIC typec detection driver
USB: serial: option: add Cellient MPL200 card
usb: typec: tcpci_maxim: Add support for Sink FRS
usb: typec: tcpci: Implement callbacks for FRS
usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)
usb: typec: tcpci_maxim: Chip level TCPC driver
usb: typec: tcpci: Add set_vbus tcpci callback
usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference
usbip: vhci_hcd: fix calling usb_hcd_giveback_urb() with irqs enabled
usb: cdc-acm: add quirk to blacklist ETAS ES58X devices
USB: serial: ftdi_sio: use cur_altsetting for consistency
USB: serial: option: Add Telit FT980-KS composition
USB: core: remove polling for /sys/kernel/debug/usb/devices
usb: typec: add support for STUSB160x Type-C controller family
usb: typec: add typec_find_pwr_opmode
usb: typec: hd3ss3220: Use OF graph API to get the connector fwnode
dt-bindings: usb: renesas,usb3-peri: Document HS and SS data bus
dt-bindings: usb: convert ti,hd3ss3220 bindings to json-schema
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
...
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAl+FqrsTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXnN8B/4sRg7j9OTzVBlDiXF2vj6vbuplTIH6
JR6S5f4PNjUg4gV6ghzSnsx1zqNhPSOr78zDqYto8vv+wqqj3thmld8+gAnSbKtt
yoAa7mhbbN1ryJiwPlZzvX4ApzGZPC7byqEi3+zPIcag6TEl8eyYJOmvY3x1zv8x
CsAb57oCC4erD0n4xlTyfuc8TLpO+EiU53PXbR9AovKQHe4m2/8LWyEbmrm5cRUR
gx8RxoLkkrqK0unzcmanbm47QodiaOTUpycs3IvaBeWZQsqSgFZdI1RAdTZNg+U+
GT8eMRXAwpgDpilPm/0n1O0PKGAsVh9Lbw8Btb/ggqnjTUlA4Z3Df23E
=Wy5n
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V updates from Wei Liu:
- a series from Boqun Feng to support page size larger than 4K
- a few miscellaneous clean-ups
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hv: clocksource: Add notrace attribute to read_hv_sched_clock_*() functions
x86/hyperv: Remove aliases with X64 in their name
PCI: hv: Document missing hv_pci_protocol_negotiation() parameter
scsi: storvsc: Support PAGE_SIZE larger than 4K
Driver: hv: util: Use VMBUS_RING_SIZE() for ringbuffer sizes
HID: hyperv: Use VMBUS_RING_SIZE() for ringbuffer sizes
Input: hyperv-keyboard: Use VMBUS_RING_SIZE() for ringbuffer sizes
hv_netvsc: Use HV_HYP_PAGE_SIZE for Hyper-V communication
hv: hyperv.h: Introduce some hvpfn helper functions
Drivers: hv: vmbus: Move virt_to_hvpfn() to hyperv header
Drivers: hv: Use HV_HYP_PAGE in hv_synic_enable_regs()
Drivers: hv: vmbus: Introduce types of GPADL
Drivers: hv: vmbus: Move __vmbus_open()
Drivers: hv: vmbus: Always use HV_HYP_PAGE_SIZE for gpadl
drivers: hv: remove cast from hyperv_die_event
Currently, dw_pcie_msi_init() allocates and maps page for msi, then
program the PCIE_MSI_ADDR_LO and PCIE_MSI_ADDR_HI. The Root Complex
may lose power during suspend-to-RAM, so when we resume, we want to
redo the latter but not the former. If designware based driver (for
example, pcie-tegra194.c) calls dw_pcie_msi_init() in resume path, the
msi page will be leaked.
As pointed out by Rob and Ard, there's no need to allocate a page for
the MSI address, we could use an address in the driver data.
To avoid map the MSI msg again during resume, we move the map MSI msg
from dw_pcie_msi_init() to dw_pcie_host_init().
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201009155505.5a580ef5@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
If MSI is disabled, there's no need to program PCIE_MSI_INTR0_MASK
and PCIE_MSI_INTR0_ENABLE registers.
Link: https://lore.kernel.org/r/20201009155436.27e67238@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
After applying "PCI: dwc: Add common iATU register support",
there is no need to set own iATU in the Keystone driver itself.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1601444167-11316-5-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
This gets iATU register area from reg property that has reg-names "atu".
In Synopsys DWC version 4.80 or later, since iATU register area is
separated from core register area, this area is necessary to get from
DT independently.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1601444167-11316-4-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
devices which require non-PCI based MSI handling.
- Cleanup historical leftovers all over the place
- Rework the code to utilize more core functionality
- Wrap XEN PCI/MSI interrupts into an irqdomain to make irqdomain
assignment to PCI devices possible.
- Assign irqdomains to PCI devices at initialization time which allows
to utilize the full functionality of hierarchical irqdomains.
- Remove arch_.*_msi_irq() functions from X86 and utilize the irqdomain
which is assigned to the device for interrupt management.
- Make the arch_.*_msi_irq() support conditional on a config switch and
let the last few users select it.
-----BEGIN PGP SIGNATURE-----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=JlqV
-----END PGP SIGNATURE-----
Merge tag 'x86-irq-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 irq updates from Thomas Gleixner:
"Surgery of the MSI interrupt handling to prepare the support of
upcoming devices which require non-PCI based MSI handling:
- Cleanup historical leftovers all over the place
- Rework the code to utilize more core functionality
- Wrap XEN PCI/MSI interrupts into an irqdomain to make irqdomain
assignment to PCI devices possible.
- Assign irqdomains to PCI devices at initialization time which
allows to utilize the full functionality of hierarchical
irqdomains.
- Remove arch_.*_msi_irq() functions from X86 and utilize the
irqdomain which is assigned to the device for interrupt management.
- Make the arch_.*_msi_irq() support conditional on a config switch
and let the last few users select it"
* tag 'x86-irq-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
PCI: MSI: Fix Kconfig dependencies for PCI_MSI_ARCH_FALLBACKS
x86/apic/msi: Unbreak DMAR and HPET MSI
iommu/amd: Remove domain search for PCI/MSI
iommu/vt-d: Remove domain search for PCI/MSI[X]
x86/irq: Make most MSI ops XEN private
x86/irq: Cleanup the arch_*_msi_irqs() leftovers
PCI/MSI: Make arch_.*_msi_irq[s] fallbacks selectable
x86/pci: Set default irq domain in pcibios_add_device()
iommm/amd: Store irq domain in struct device
iommm/vt-d: Store irq domain in struct device
x86/xen: Wrap XEN MSI management into irqdomain
irqdomain/msi: Allow to override msi_domain_alloc/free_irqs()
x86/xen: Consolidate XEN-MSI init
x86/xen: Rework MSI teardown
x86/xen: Make xen_msi_init() static and rename it to xen_hvm_msi_init()
PCI/MSI: Provide pci_dev_has_special_msi_domain() helper
PCI_vmd_Mark_VMD_irqdomain_with_DOMAIN_BUS_VMD_MSI
irqdomain/msi: Provide DOMAIN_BUS_VMD_MSI
x86/irq: Initialize PCI/MSI domain at PCI init time
x86/pci: Reducde #ifdeffery in PCI init code
...
Fix sparse build warning:
drivers/pci/controller/pcie-iproc-platform.c:102:33: warning: Using plain integer as NULL pointer
The map_irq member of the struct iproc_pcie takes a function pointer
serving as a callback to map interrupts, therefore we should pass a NULL
pointer to it rather than a integer in the iproc_pcie_pltfm_probe()
function.
Related:
commit b64aa11eb2 ("PCI: Set bridge map_irq and swizzle_irq to
default functions")
Link: https://lore.kernel.org/r/20200922194932.465925-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Enable pci-meson to build as a module whenever ARCH_MESON is enabled.
Link: https://lore.kernel.org/r/20200918181251.32423-1-khilman@baylibre.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: Yue Wang <yue.wang@amlogic.com>
Old ATF automatically power on pcie phy and does not provide SMC call for
phy power on functionality which leads to aardvark initialization failure:
[ 0.330134] mvebu-a3700-comphy d0018300.phy: unsupported SMC call, try updating your firmware
[ 0.338846] phy phy-d0018300.phy.1: phy poweron failed --> -95
[ 0.344753] advk-pcie d0070000.pcie: Failed to initialize PHY (-95)
[ 0.351160] advk-pcie: probe of d0070000.pcie failed with error -95
This patch fixes above failure by ignoring 'not supported' error in
aardvark driver. In this case it is expected that phy is already power on.
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://lore.kernel.org/r/20200902144344.16684-3-pali@kernel.org
Fixes: 366697018c ("PCI: aardvark: Add PHY support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: <stable@vger.kernel.org> # 5.8+: ea17a0f153: phy: marvell: comphy: Convert internal SMCC firmware return codes to errno
The value assigned to msi_val after the inner loop finishes its run is
never used for anything, and it is also immediately overridden in the
line that follows with the return value from the xgene_msi_int_read()
function.
Since the value of msi_val following the inner loop completion is never
used in any meaningful way the assignment can be removed.
Addresses-Coverity-ID: 1437183 ("Unused value")
Link: https://lore.kernel.org/r/20200922030257.459898-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Simplify the return expression by removing useless code.
Link: https://lore.kernel.org/r/20200921082447.2591877-1-liushixin2@huawei.com
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
module_bcma_driver() makes the code simpler by eliminating
boilerplate code.
Link: https://lore.kernel.org/r/20200918030829.3946025-1-liushixin2@huawei.com
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Now that the support is in place with previous commits, we add several
chips that use the BrcmSTB driver.
Link: https://lore.kernel.org/r/20200911175232.19016-11-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
The proper value of the parameter SCB_MAX_BURST_SIZE varies per chip. The
2711 family requires 128B whereas other devices can employ 512. The
assignment is complicated by the fact that the values for this two-bit
field have different meanings;
Value Type_Generic Type_7278
00 Reserved 128B
01 128B 256B
10 256B 512B
11 512B Reserved
Link: https://lore.kernel.org/r/20200911175232.19016-10-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Older BrcmSTB chips do not have a separate register for MSI interrupts; the
MSIs are in a register that also contains unrelated interrupts. In
addition, the interrupts lie in bits [31..24] for these legacy chips. This
commit provides common code for both legacy and non-legacy MSI interrupt
registers.
Link: https://lore.kernel.org/r/20200911175232.19016-9-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
The Raspberry Pi (RPI) is currently the only chip using this driver
(pcie-brcmstb.c). There, only one memory controller is used, without an
extension region, and the SCB0 viewport size is set to the size of the
first and only dma-range region. Other BrcmSTB SOCs have more complicated
memory configurations that require setting additional viewport sizes.
BrcmSTB PCIe controllers are intimately connected to the memory
controller(s) on the SOC. The SOC may have one to three memory
controllers; they are indicated by the term SCBi. Each controller has a
base region and an optional extension region. In physical memory, the base
and extension regions of a controller are not adjacent, but in PCIe-space
they are.
There is a "viewport" for each memory controller that allows DMA from
endpoint devices. Each viewport's size must be set to a power of two, and
that size must be equal to or larger than the amount of memory each
controller supports which is the sum of base region and its optional
extension. Further, the 1-3 viewports are also adjacent in PCIe-space.
Unfortunately the viewport sizes cannot be ascertained from the
"dma-ranges" property so they have their own property, "brcm,scb-sizes".
This is because dma-range information does not indicate what memory
controller it is associated. For example, consider the following case
where the size of one dma-range is 2GB and the second dma-range is 1GB:
/* Case 1: SCB0 size set to 4GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)
/* Case 2: SCB0 size set to 2GB, SCB1 size set to 1GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)
By just looking at the dma-ranges information, one cannot tell which
situation applies. That is why an additional property is needed. Its
length indicates the number of memory controllers being used and each value
indicates the viewport size.
Note that the RPI DT does not have a "brcm,scb-sizes" property value,
as it is assumed that it only requires one memory controller and no
extension. So the optional use of "brcm,scb-sizes" will be backwards
compatible.
One last layer of complexity exists: all of the viewports sizes must be
added and rounded up to a power of two to determine what the "BAR" size is.
Further, an offset must be given that indicates the base PCIe address of
this "BAR". The use of the term BAR is typically associated with endpoint
devices, and the term is used here because the PCIe HW may be used as an RC
or an EP. In the former case, all of the system memory appears in a single
"BAR" region in PCIe memory. As it turns out, BrcmSTB PCIe HW is rarely
used in the EP role and its system of mapping memory is an artifact that
requires multiple dma-ranges regions.
Link: https://lore.kernel.org/r/20200911175232.19016-8-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Some STB chips have a special purpose reset controller named RESCAL (reset
calibration). The PCIe HW can now control RESCAL to start and stop its
operation. On probe(), the RESCAL is deasserted and the driver goes
through the sequence of setting registers and reading status in order to
start the internal PHY that is required for the PCIe.
Link: https://lore.kernel.org/r/20200911175232.19016-7-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
pci_restore_msi_state() directly writes the MSI/MSI-X related registers
via MMIO. On a physical machine, this works perfectly; for a Linux VM
running on a hypervisor, which typically enables IOMMU interrupt remapping,
the hypervisor usually should trap and emulate the MMIO accesses in order
to re-create the necessary interrupt remapping table entries in the IOMMU,
otherwise the interrupts can not work in the VM after hibernation.
Hyper-V is different from other hypervisors in that it does not trap and
emulate the MMIO accesses, and instead it uses a para-virtualized method,
which requires the VM to call hv_compose_msi_msg() to notify the hypervisor
of the info that would be passed to the hypervisor in the case of the
trap-and-emulate method. This is not an issue to a lot of PCI device
drivers, which destroy and re-create the interrupts across hibernation, so
hv_compose_msi_msg() is called automatically. However, some PCI device
drivers (e.g. the in-tree GPU driver nouveau and the out-of-tree Nvidia
proprietary GPU driver) do not destroy and re-create MSI/MSI-X interrupts
across hibernation, so hv_pci_resume() has to call hv_compose_msi_msg(),
otherwise the PCI device drivers can no longer receive interrupts after
the VM resumes from hibernation.
Hyper-V is also different in that chip->irq_unmask() may fail in a
Linux VM running on Hyper-V (on a physical machine, chip->irq_unmask()
can not fail because unmasking an MSI/MSI-X register just means an MMIO
write): during hibernation, when a CPU is offlined, the kernel tries
to move the interrupt to the remaining CPUs that haven't been offlined
yet. In this case, hv_irq_unmask() -> hv_do_hypercall() always fails
because the vmbus channel has been closed: here the early "return" in
hv_irq_unmask() means the pci_msi_unmask_irq() is not called, i.e. the
desc->masked remains "true", so later after hibernation, the MSI interrupt
always remains masked, which is incorrect. Refer to cpu_disable_common()
-> fixup_irqs() -> irq_migrate_all_off_this_cpu() -> migrate_one_irq():
static bool migrate_one_irq(struct irq_desc *desc)
{
...
if (maskchip && chip->irq_mask)
chip->irq_mask(d);
...
err = irq_do_set_affinity(d, affinity, false);
...
if (maskchip && chip->irq_unmask)
chip->irq_unmask(d);
Fix the issue by calling pci_msi_unmask_irq() unconditionally in
hv_irq_unmask(). Also suppress the error message for hibernation because
the hypercall failure during hibernation does not matter (at this time
all the devices have been frozen). Note: the correct affinity info is
still updated into the irqdata data structure in migrate_one_irq() ->
irq_do_set_affinity() -> hv_set_affinity(), so later when the VM
resumes, hv_pci_restore_msi_state() is able to correctly restore
the interrupt with the correct affinity.
Link: https://lore.kernel.org/r/20201002085158.9168-1-decui@microsoft.com
Fixes: ac82fc8327 ("PCI: hv: Add hibernation support")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
PCI host bridge driver can be probed before the gpiochip it requires,
so, of_get_named_gpio() can return -EPROBE_DEFER. Current code lets the
kirin_pcie_probe() directly return -ENODEV, which results in the PCI
host controller driver probe failure; with this error code the PCI host
controller driver will not be probed again when the gpiochip driver is
loaded.
Fix the above issue by letting kirin_pcie_probe() return -EPROBE_DEFER in
such a case.
Link: https://lore.kernel.org/r/20200918123800.19983-1-huobean@gmail.com
Signed-off-by: Bean Huo <beanhuo@micron.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Use DEFINE_SEQ_ATTRIBUTE macro to simplify the code.
Link: https://lore.kernel.org/r/20200916025025.3992783-1-liushixin2@huawei.com
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Add missing documentation for the parameter "version" and "num_version"
of the hv_pci_protocol_negotiation() function and resolve build time
kernel-doc warnings:
drivers/pci/controller/pci-hyperv.c:2535: warning: Function parameter
or member 'version' not described in 'hv_pci_protocol_negotiation'
drivers/pci/controller/pci-hyperv.c:2535: warning: Function parameter
or member 'num_version' not described in 'hv_pci_protocol_negotiation'
No change to functionality intended.
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20200925234753.1767227-1-kw@linux.com
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Add PCIe EP mode support for ls1088a and ls2088a, there are some
difference between LS1 and LS2 platform, so refactor the code of
the EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-10-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
dw_pcie_ep_raise_msix_irq was never called in the exisitng driver
before, because the ls1046a platform don't support the MSIX feature
and msix_capable was always set to false.
Now that add the ls1088a platform with MSIX support, use the doorbell
method to support the MSIX feature.
Link: https://lore.kernel.org/r/20200918080024.13639-9-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The different PCIe controller in one board may be have different
capability of MSI or MSIX, so change the way of getting the MSI
capability, make it more flexible.
Link: https://lore.kernel.org/r/20200918080024.13639-8-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Fix some format issue of the code in EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-7-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Each PF of EP device should have its own MSI or MSIX capabitily
struct, so create a dw_pcie_ep_func struct and move the msi_cap
and msix_cap to this struct from dw_pcie_ep, and manage the PFs
via a list.
Link: https://lore.kernel.org/r/20200918080024.13639-5-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Move the function of getting MSI capability to the front of init
function, because the init function of the EP platform driver will use
the return value by the function of getting MSI capability.
Link: https://lore.kernel.org/r/20200918080024.13639-4-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add the doorbell mode of MSI-X in DWC EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-3-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add multiple PFs support for DWC, due to different PF have different
config space, we use func_conf_select callback function to access
the different PF's config space, the different chip company need to
implement this callback function when use the DWC IP core and intend
to support multiple PFs feature.
Link: https://lore.kernel.org/r/20200918080024.13639-2-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The PERST# bit was moved to a different register in 7278-type STB chips.
In addition, the polarity of the bit was also changed; for other chips
writing a 1 specified assert; for 7278-type chips, writing a 0 specifies
assert. Of course, PERST# is a PCIe asserted-low signal.
While we are here, also change the bridge_sw_init_set() functions so like
the perst_set() functions they are chip specific and we no longer rely on
data wrt chip specific field mask and shift values.
Link: https://lore.kernel.org/r/20200911175232.19016-6-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Broadcom Set-top (BrcmSTB) boards typically support S2, S3, and S5 suspend
and resume. Now the PCIe driver may do so as well.
Link: https://lore.kernel.org/r/20200911175232.19016-5-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Add in compatibility strings and code for three Broadcom STB chips. Some
of the register locations, shifts, and masks are different for certain
chips, requiring the use of different constants based on of_id.
We would like to add the following at this time to the match list but we
need to wait until the end of this patchset so that everything works.
{ .compatible = "brcm,bcm7211-pcie", .data = &generic_cfg },
{ .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg },
{ .compatible = "brcm,bcm7216-pcie", .data = &bcm7278_cfg },
{ .compatible = "brcm,bcm7445-pcie", .data = &generic_cfg },
Link: https://lore.kernel.org/r/20200911175232.19016-4-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Have PCIE_BRCMSTB depend on ARCH_BRCMSTB. Also set the default value to
ARCH_BRCMSTB.
Link: https://lore.kernel.org/r/20200911175232.19016-2-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
The arch_.*_msi_irq[s] fallbacks are compiled in whether an architecture
requires them or not. Architectures which are fully utilizing hierarchical
irq domains should never call into that code.
It's not only architectures which depend on that by implementing one or
more of the weak functions, there is also a bunch of drivers which relies
on the weak functions which invoke msi_controller::setup_irq[s] and
msi_controller::teardown_irq.
Make the architectures and drivers which rely on them select them in Kconfig
and if not selected replace them by stub functions which emit a warning and
fail the PCI/MSI interrupt allocation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200826112333.992429909@linutronix.de
Devices on the VMD bus use their own MSI irq domain, but it is not
distinguishable from regular PCI/MSI irq domains. This is required
to exclude VMD devices from getting the irq domain pointer set by
interrupt remapping.
Override the default bus token.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112333.047315047@linutronix.de
pci_msi_get_hwirq() and pci_msi_set_desc are not longer special. Enable the
generic MSI domain ops in the core and PCI MSI code unconditionally and get
rid of the x86 specific implementations in the X86 MSI code and in the
hyperv PCI driver.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200826112332.564274859@linutronix.de
Convert the interrupt remap drivers to retrieve the pci device from the msi
descriptor and use info::hwirq.
This is the first step to prepare x86 for using the generic MSI domain ops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112332.466405395@linutronix.de
VMD has it's own PCI/MSI interrupt domain which is not in any way depending
on the x86 vector domain. PCI devices behind VMD share the VMD MSIX vector
entries via a VMD specific message translation to the actual VMD MSIX
vector. The VMD device interrupt handler for the VMD MSIX vectors invokes
all interrupt handlers of the devices which share a vector.
Making the x86 vector domain the actual parent of the VMD irq domain is
pointless and actually counterproductive. When a device interrupt is
requested then it will activate the interrupt which traverses down the
hierarchy and consumes an interrupt vector in the vector domain which is
never used.
The domain is self contained and has no parent dependencies, so just hand
in NULL for the parent and be done with it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200826112330.928952181@linutronix.de
The HiSilicon HIP PCIe controller is capable of handling errors
on root port and performing port reset separately at each root port.
Add error handling driver for HIP PCIe controller to log
and report recoverable errors. Perform root port reset and restore
link status after the recovery.
Following are some of the PCIe controller's recoverable errors
1. completion transmission timeout error.
2. CRS retry counter over the threshold error.
3. ECC 2 bit errors
4. AXI bresponse/rresponse errors etc.
The driver placed in the drivers/pci/controller/ because the
HIP PCIe controller does not use DWC IP.
Link: https://lore.kernel.org/r/20200903123456.1823-3-shiju.jose@huawei.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Convert the remaining cases of register accesses using dbi_base rather
than dw_pcie_(read|write)[bwl]_dbi accessors.
Link: https://lore.kernel.org/r/20200821035420.380495-41-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
The Designware controller has common registers to set number of fast
training sequence ordered sets. The Artpec6, Intel, and Tegra driver
initialize these register fields. Let's move the initialization to the
common setup code and drivers just have to provide the value.
There's a slight change in that the common clock mode N_FTS field is
now initialized. Previously only the Intel driver set this. It's not
clear from the code if common clock mode is used in the Artpec6 or Tegra
driver. It depends on the DWC configuration. Given the field is not
initialized while the others are, it seems unlikely common clock mode
is used.
Link: https://lore.kernel.org/r/20200821035420.380495-40-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
'max_width' is read, but never used, so let's remove it.
Link: https://lore.kernel.org/r/20200821035420.380495-39-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The PCI_CAP_ID_EXP offset is only needed by intel_pcie_link_setup(), so
let's retrieve it there and avoid storing the offset.
Link: https://lore.kernel.org/r/20200821035420.380495-38-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
A driver doesn't need to check for DT 'device_type' property, so let's
remove the check.
Link: https://lore.kernel.org/r/20200821035420.380495-37-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The Intel driver is the only one to set PORT_LINK_DLL_LINK_EN. The
default value is set and it seems pretty certain that enabling link
initialization is always required. Maybe it could just be dropped from
the Intel driver, but lets move setting it into the common code to be
sure.
Link: https://lore.kernel.org/r/20200821035420.380495-36-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The root bus checks rework in d84c572de1 ("PCI: rockchip: Use
pci_is_root_bus() to check if bus is root bus") caused a regression whereby
in rockchip_pcie_valid_device() if the bus parameter is the root bus and
the dev value == 0, the function should return 1 (ie true) without checking
if the bus->parent pointer is a root bus because that triggers a NULL
pointer dereference.
Fix this by streamlining the root bus detection.
Fixes: d84c572de1 ("PCI: rockchip: Use pci_is_root_bus() to check if bus is root bus")
Link: https://lore.kernel.org/r/20200904140904.944-1-lorenzo.pieralisi@arm.com
Reported-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Tested-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
The core interrupt code expects the irq_set_affinity call to update the
effective affinity for the interrupt. This was not being done, so update
iproc_msi_irq_set_affinity() to do so.
Link: https://lore.kernel.org/r/20200803035241.7737-1-mark.tomlinson@alliedtelesis.co.nz
Fixes: 3bc2b23488 ("PCI: iproc: Add iProc PCIe MSI support")
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
The mvebu host controller driver allocates an msi_controller structure
pointer without allocating the structure and initializing its methods,
which makes the pointer useless.
This means that the PCI IRQ MSI layer ignores it and that after all it
should not really be needed.
Remove it.
Link: https://lore.kernel.org/r/20200904142132.6054-1-lorenzo.pieralisi@arm.com
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The ATU registers are only accessed in pcie-designware.c and can be private
to it.
Link: https://lore.kernel.org/r/20200821035420.380495-34-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The DBI2 appears to be write-only and there's no read accesses in the code
anyways, so let's remove all the read_dbi2 related code.
Link: https://lore.kernel.org/r/20200821035420.380495-33-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The Tegra driver has its own defines for common Designware Port Logic
registers. Convert it to use the standard register definitions.
Link: https://lore.kernel.org/r/20200821035420.380495-32-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
While the Designware controller appears to hard code the PCI_CAP_ID_EXP
capability register at 0x70, there's no need to hard code this in the
driver as it is discoverable.
Link: https://lore.kernel.org/r/20200821035420.380495-31-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: linux-omap@vger.kernel.org
The QCom driver has its own defines for common PCI config space
registers. It also hard codes the capability register offsets which are
discoverable. Convert it to use the standard register definitions.
Link: https://lore.kernel.org/r/20200821035420.380495-30-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-arm-msm@vger.kernel.org
The i.MX6 driver has its own defines for common PCI config space
registers. It also hard codes the capability register offsets which are
discoverable. Convert it to use the standard register definitions.
Link: https://lore.kernel.org/r/20200821035420.380495-29-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
The meson 'elbi' registers are just the Designware 'dbi' space and all
the registers accessed are either standard PCI config space or DWC port
logic registers. Convert the accesses to use the common defines and
register accessors.
Link: https://lore.kernel.org/r/20200821035420.380495-28-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: linux-amlogic@lists.infradead.org
The common Designware init already initializes the RC PCI_COMMAND, BAR0
and BAR1 registers.
The only difference here is the common code sets SERR. If clearing SERR
is what's desired, then the Meson driver should do that instead.
Link: https://lore.kernel.org/r/20200821035420.380495-27-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
The meson lanes initialization is the same DWC port logic registers as
in dw_pcie_setup(). We just need to initialize 'num_lanes' to 1 to do
the same init.
dw_pcie_setup_rc() sets the PORT_LOGIC_SPEED_CHANGE bit, so setting it
can be dropped.
Link: https://lore.kernel.org/r/20200821035420.380495-26-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: linux-amlogic@lists.infradead.org
"Fast Link Mode" is a simulation environment speed up setting which should
never be set and the default is not set. However some Amlogic platforms
have it set (by firmware presumably). See commit 87dccf0932 ("PCI:
amlogic: meson: Don't use FAST_LINK_MODE to set up link") for more
information. Let's clear it in core DWC code so we can drop some vendor
specific code.
Link: https://lore.kernel.org/r/20200821035420.380495-25-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Add a 'num_lanes' field to allow drivers to provide a the number of lanes
if not in DT or using a custom DT property. A driver can provide a
non-zero value which is used if the DT doesn't have a 'num-lanes'
property.
Link: https://lore.kernel.org/r/20200821035420.380495-24-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
PCIE_LINK_WIDTH_SPEED_CONTROL is already defined in pcie-designware.h,
so remove it from the i.MX6 driver.
Link: https://lore.kernel.org/r/20200821035420.380495-23-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
The DWC core driver already parses and stores the 'num-viewport' DT
property, so there is no need for the Keystone driver to store it.
Link: https://lore.kernel.org/r/20200821035420.380495-21-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The config space is divided in half for type 0 and type 1 accesses, but
this is pointless as there's only one iATU window which is
reconfigured on each access.
The only platform doing something custom is TI Keystone (surprise!).
It does its own mapping of the config space to avoid spliting the
config space and never actually uses va_cfg1_base as it has its own
config space accessors. With the splitting removed, Keystone can use the
default mapping of config space.
Link: https://lore.kernel.org/r/20200821035420.380495-20-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The PCI bridge resources are stored in pci_host_bridge.windows, so
there's no need to store them in a DWC specific struct. There's also no
need to parse the resources and store them a 2nd time as they are mainly
used for one time setup of iATU windows.
Link: https://lore.kernel.org/r/20200821035420.380495-19-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The pci_host_bridge struct already has a pointer to its pci_bus, so
let's convert the one user to use the bridge struct and remove the
private 'root_bus' pointer.
Link: https://lore.kernel.org/r/20200821035420.380495-18-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Now that there are no more .scan_bus() callbacks, we can remove it and just
use pci_host_probe().
Link: https://lore.kernel.org/r/20200821035420.380495-17-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
TI keystone is the only Designware driver using .scan_bus(). This
function pointer is the only thing preventing the Designware driver from
using pci_host_probe(). Let's use the pci_ops.add_bus hook instead.
Link: https://lore.kernel.org/r/20200821035420.380495-16-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that all the platforms with custom config access handling define
their own pci_ops, let's split the default config accessors to use
different pci_ops for root and child buses. With this, we can use the
generic config accessors. The child bus accesses mainly require a
.map_bus() hook to reconfigure the iATU on each config space access.
Link: https://lore.kernel.org/r/20200821035420.380495-14-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that all the drivers needing custom config accessors have been
converted to define their own pci_ops, we can remove the DWC specific
function callbacks {rd,wr}_{own,other}_conf.
Link: https://lore.kernel.org/r/20200821035420.380495-13-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the HiSilicon histb driver to use the standard pci_ops
for root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-12-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Samsung Exynos driver to use the standard pci_ops for
root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-11-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: linux-samsung-soc@vger.kernel.org
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the HiSilicon Kirin driver to use the standard pci_ops
for root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-10-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Amlogic meson driver to use the standard pci_ops for
root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-9-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Tegra driver to use the standard pci_ops for root
bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-8-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the TI Keystone driver to use the standard pci_ops for
config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-7-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Amazon driver to use the standard pci_ops for child
bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-6-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The Designware root port config space is memory mapped accesses via the
DBI space by default. Add a common implementation
dw_pcie_own_conf_map_bus() for platforms to use.
Link: https://lore.kernel.org/r/20200821035420.380495-5-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
This comment still refers to the old driver pathname,
when all PCI drivers were located directly under the
drivers/pci directory.
Anyway the function name itself is enough, so we can
remove the overabundant path reference.
Link: https://lore.kernel.org/r/20200623074851.7832-1-f.suligoi@asem.it
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When devm_clk_get() returns -EPROBE_DEFER, i.MX6 PCI driver should
NOT print error message, use dev_err_probe() to handle it.
Link: https://lore.kernel.org/r/1597109364-4739-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Move code which belongs to link training (delays and resets) into
advk_pcie_train_link() function, so everything related to link training,
including timings is at one place.
After experiments it can be observed that link training in aardvark
hardware is very sensitive to timings and delays, so it is a good idea to
have this code at the same place as link training calls.
This patch does not change behavior of aardvark initialization.
Link: https://lore.kernel.org/r/20200907111038.5811-6-pali@kernel.org
Tested-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Providing driver's 'remove' function allows kernel to bind and unbind devices
from aardvark driver. It also allows to build aardvark driver as a module.
Compiling aardvark as a module simplifies development and debugging of
this driver as it can be reloaded at runtime without the need to reboot
to new kernel.
Link: https://lore.kernel.org/r/20200907111038.5811-5-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Include linux/gpio/consumer.h instead of linux/gpio.h, as is said in the
latter file.
This was reported by kernel test bot when compiling for s390.
drivers/pci/controller/pci-aardvark.c:350:2: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-aardvark.c:1074:21: error: implicit declaration of function 'devm_gpiod_get_from_of_node' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-aardvark.c:1076:14: error: use of undeclared identifier 'GPIOD_OUT_LOW'
Link: https://lore.kernel.org/r/202006211118.LxtENQfl%25lkp@intel.com
Link: https://lore.kernel.org/r/20200907111038.5811-2-pali@kernel.org
Fixes: 5169a9851d ("PCI: aardvark: Issue PERST via GPIO")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Qsdk U-Boot can incorrectly leave the PCIe interface in an undefined
state if bootm command is used instead of bootipq. This is caused by the
not deinit of PCIe when bootm is called. Reset the PCIe before init
anyway to fix this U-Boot bug.
Link: https://lore.kernel.org/r/20200901124955.137-1-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable@vger.kernel.org # v4.19+
Some fields in the host bridge structure are now initialized
by default in the PCI/OF core functions therefore their
initialization in the host controller driver is superfluous.
Remove it.
Link: https://lore.kernel.org/r/20200904142710.8018-1-lorenzo.pieralisi@arm.com
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Link: https://lore.kernel.org/r/20200818133739.463193-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
Cc: Andrew Murray <amurray@thegoodpenguin.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pci@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
In preparation to allow drivers to set their own root and child pci_ops
instead of using the DWC specific config space ops, we need to make
the pci_host_bridge pointer available and move setting the bridge->ops
and bridge->child_ops pointer to before the .host_init() hook.
Link: https://lore.kernel.org/r/20200821035420.380495-4-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The Designware DBI space contains the root bus bridge config space.
Platforms needing custom {rd,wr}_own_conf functions are also the ones
needing custom {read,write}_dbi ops functions and the access sequences
are the same.
Replace all dw_pcie_{rd,wr}_own_conf() calls with the DBI variants in
preparation to remove dw_pcie_{rd,wr}_own_conf().
Link: https://lore.kernel.org/r/20200821035420.380495-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The current check will result in the multiple function device
fails to initialize. So fix the check by masking out the
multiple function bit.
Link: https://lore.kernel.org/r/20200818092746.24366-1-Zhiqiang.Hou@nxp.com
Fixes: 0b24134f78 ("PCI: dwc: Add validation that PCIe core is set to correct mode")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9ML+IeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGA8EIAIy/kTbFS0yrE9yV
hb98oX0z9+EU9YQg9vhaRWwPd+rJF/JMQZLqYcwbhjG9abaUL3T3fEcSAefMHw8E
LAt+hYzA38dHt7tqhsFQX3vV1VorvDVICBVN0yRPRWKKikq4OPIHzaAR9tleGAF5
8btQisl1PjN+obwYmLuNb6aX16OCwAF+uXOwehcoJs9dvMNhwtXRzfOflWzOvOo6
tE0bHErlylLDfLv4ZzEfczTdks4QJZ7C0xLSf3oN9AAynW42Xnhct4hi8qZY/hCf
CMaqeN4hdpub6TvQIqBdDqMMjEXGFgeNSnAEBQY9VpvUqz8NTu6sQxwgJEKDF5tg
d81lv2c=
=uW/F
-----END PGP SIGNATURE-----
Merge 5.9-rc3 into usb-next
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 44331189f9.
Now that the VL805 init routine is run through a reset controller driver
the device dependencies are being taken care of by the device core. No
need to do it manually here.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-10-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Remove redundant logging for platform_get_irq() errors (Krzysztof
Wilczyński)
* pci/irq-error:
PCI: Remove dev_err() when handing an error from platform_get_irq()
- Use pci_host_bridge.windows list directly instead of splicing in a
temporary list for cadence, mvebu, host-common (Rob Herring)
- Use pci_host_probe() instead of open-coding all the pieces for altera,
brcmstb, iproc, mobiveil, rcar, rockchip, tegra, v3, versatile, xgene,
xilinx, xilinx-nwl (Rob Herring)
- Convert to devm_platform_ioremap_resource_byname() instead of open-coding
platform_get_resource_byname() and devm_ioremap_resource() for altera,
cadence, mediatek, rockchip, tegra, xgene (Dejin Zheng)
- Convert to devm_platform_ioremap_resource() instead of open-coding
platform_get_resource() and devm_ioremap_resource() for aardvark,
brcmstb, exynos, ftpci100, versatile (Dejin Zheng)
- Remove redundant error messages from devm_pci_remap_cfg_resource()
callers (Dejin Zheng)
- Drop useless PCI_ENABLE_PROC_DOMAINS from versatile driver (Rob Herring)
- Default host bridge parent device to the platform device (Rob Herring)
- Drop unnecessary zeroing of host bridge fields (Rob Herring)
- Use pci_is_root_bus() instead of tracking root bus number separately in
aardvark, designware (imx6, keystone, designware-host), mobiveil,
xilinx-nwl, xilinx, rockchip, rcar (Rob Herring)
- Set host bridge bus number in pci_scan_root_bus_bridge() instead of each
driver for aardvark, designware-host, host-common, mediatek, rcar, tegra,
v3-semi (Rob Herring)
- Use bridge resources instead of parsing DT 'ranges' again for cadence
(Rob Herring)
- Remove private bus number and range from cadence (Rob Herring)
- Use devm_pci_alloc_host_bridge() to simplify rcar (Rob Herring)
- Use struct pci_host_bridge.windows list directly rather than a temporary
(Rob Herring)
- Reduce OF "missing non-prefetchable window" from error to warning message
(Rob Herring)
- Convert rcar-gen2 from old Arm-specific pci_common_init_dev() to new
arch-independent interfaces (Rob Herring)
- Move DT resource setup into devm_pci_alloc_host_bridge() (Rob Herring)
- Set bridge map_irq and swizzle_irq to default functions; drivers that
don't support legacy IRQs (iproc) need to undo this (Rob Herring)
* pci/host-probe-refactor:
PCI: Set bridge map_irq and swizzle_irq to default functions
PCI: Move DT resource setup into devm_pci_alloc_host_bridge()
PCI: rcar-gen2: Convert to use modern host bridge probe functions
PCI: of: Reduce missing non-prefetchable memory region to a warning
PCI: rcar: Use struct pci_host_bridge.windows list directly
PCI: rcar: Use devm_pci_alloc_host_bridge()
PCI: cadence: Remove private bus number and range storage
PCI: cadence: Use bridge resources for outbound window setup
PCI: Move setting pci_host_bridge.busnr out of host drivers
PCI: rcar: Use pci_is_root_bus() to check if bus is root bus
PCI: rockchip: Use pci_is_root_bus() to check if bus is root bus
PCI: xilinx: Use pci_is_root_bus() to check if bus is root bus
PCI: xilinx-nwl: Use pci_is_root_bus() to check if bus is root bus
PCI: mobiveil: Use pci_is_root_bus() to check if bus is root bus
PCI: designware: Use pci_is_root_bus() to check if bus is root bus
PCI: aardvark: Use pci_is_root_bus() to check if bus is root bus
PCI: Drop unnecessary zeroing of bridge fields
PCI: Set default bridge parent device
PCI: versatile: Drop flag PCI_ENABLE_PROC_DOMAINS
PCI: controller: Remove duplicate error message
PCI: controller: Convert to devm_platform_ioremap_resource()
PCI: controller: Convert to devm_platform_ioremap_resource_byname()
PCI: xilinx: Use pci_host_probe() to register host
PCI: xilinx-nwl: Use pci_host_probe() to register host
PCI: rockchip: Use pci_host_probe() to register host
PCI: rcar: Use pci_host_probe() to register host
PCI: iproc: Use pci_host_probe() to register host
PCI: altera: Use pci_host_probe() to register host
PCI: xgene: Use pci_host_probe() to register host
PCI: versatile: Use pci_host_probe() to register host
PCI: v3: Use pci_host_probe() to register host
PCI: tegra: Use pci_host_probe() to register host
PCI: mobiveil: Use pci_host_probe() to register host
PCI: brcmstb: Use pci_host_probe() to register host
PCI: host-common: Use struct pci_host_bridge.windows list directly
PCI: mvebu: Use struct pci_host_bridge.windows list directly
PCI: cadence: Use struct pci_host_bridge.windows list directly
# Conflicts:
# drivers/pci/controller/cadence/pcie-cadence-host.c
- Set up mvebu BAR 0 so MSI works even if bootloader doesn't do this
(Shmuel Hazan)
* remotes/lorenzo/pci/mvebu:
PCI: mvebu: Setup BAR0 in order to fix MSI
- Fix loongson class code quirk so it happens early enough (Tiezhu Yang)
* remotes/lorenzo/pci/loongson:
PCI: loongson: Use DECLARE_PCI_FIXUP_EARLY for bridge_class_quirk()
- Fix hv timing issue that causes kdump failures (Wei Hu)
- Make some hv functions static (Wei Yongjun)
* remotes/lorenzo/pci/hv:
PCI: hv: Make some functions static
PCI: hv: Fix a timing issue which causes kdump to fail occasionally
