Commit a97f8783a9 ("igb: unbreak I2C bit-banging on i350") introduced
code to change I2C settings to bit banging unconditionally.
However, this patch introduced a regression: On an Intel S2600CWR
Server Board with three NICs:
- 1x dual-port copper
Intel I350 Gigabit Network Connection [8086:1521] (rev 01)
fw 1.63, 0x80000dda
- 2x quad-port SFP+ with copper SFP Avago ABCU-5700RZ
Intel I350 Gigabit Fiber Network Connection [8086:1522] (rev 01)
fw 1.52.0
the SFP NICs no longer get link at all. Reverting commit a97f8783a9
or switching to the Intel out-of-tree driver both fix the problem.
Per the igb out-of-tree driver, I2C bit banging on i350 depends on
support for an external thermal sensor (ETS). However, commit
a97f8783a9 added bit banging unconditionally. Additionally, the
out-of-tree driver always calls init_thermal_sensor_thresh on probe,
while our driver only calls init_thermal_sensor_thresh only in
igb_reset(), and only if an ETS is present, ignoring the internal
thermal sensor. The affected SFPs don't provide an ETS. Per Intel,
the behaviour is a result of i350 firmware requirements.
This patch fixes the problem by aligning the behaviour to the
out-of-tree driver:
- split igb_init_i2c() into two functions:
- igb_init_i2c() only performs the basic I2C initialization.
- igb_set_i2c_bb() makes sure that E1000_CTRL_I2C_ENA is set
and enables bit-banging.
- igb_probe() only calls igb_set_i2c_bb() if an ETS is present.
- igb_probe() calls init_thermal_sensor_thresh() unconditionally.
- igb_reset() aligns its behaviour to igb_probe(), i. e., call
igb_set_i2c_bb() if an ETS is present and call
init_thermal_sensor_thresh() unconditionally.
Fixes: a97f8783a9 ("igb: unbreak I2C bit-banging on i350")
Tested-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Co-developed-by: Jamie Bainbridge <jbainbri@redhat.com>
Signed-off-by: Jamie Bainbridge <jbainbri@redhat.com>
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230214185549.1306522-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix handling of the tsync interrupt to compare the pin number with
IGB_N_SDP instead of IGB_N_EXTTS/IGB_N_PEROUT and fix the indexing to
the perout array.
Fixes: cf99c1dd7b ("igb: move PEROUT and EXTTS isr logic to separate functions")
Reported-by: Matt Corallo <ntp-lists@mattcorallo.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230213185822.3960072-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCY+bZrwAKCRDbK58LschI
gzi4AP4+TYo0jnSwwkrOoN9l4f5VO9X8osmj3CXfHBv7BGWVxAD/WnvA3TDZyaUd
agIZTkRs6BHF9He8oROypARZxTeMLwM=
=nO1C
-----END PGP SIGNATURE-----
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-02-11
We've added 96 non-merge commits during the last 14 day(s) which contain
a total of 152 files changed, 4884 insertions(+), 962 deletions(-).
There is a minor conflict in drivers/net/ethernet/intel/ice/ice_main.c
between commit 5b246e533d ("ice: split probe into smaller functions")
from the net-next tree and commit 66c0e13ad2 ("drivers: net: turn on
XDP features") from the bpf-next tree. Remove the hunk given ice_cfg_netdev()
is otherwise there a 2nd time, and add XDP features to the existing
ice_cfg_netdev() one:
[...]
ice_set_netdev_features(netdev);
netdev->xdp_features = NETDEV_XDP_ACT_BASIC | NETDEV_XDP_ACT_REDIRECT |
NETDEV_XDP_ACT_XSK_ZEROCOPY;
ice_set_ops(netdev);
[...]
Stephen's merge conflict mail:
https://lore.kernel.org/bpf/20230207101951.21a114fa@canb.auug.org.au/
The main changes are:
1) Add support for BPF trampoline on s390x which finally allows to remove many
test cases from the BPF CI's DENYLIST.s390x, from Ilya Leoshkevich.
2) Add multi-buffer XDP support to ice driver, from Maciej Fijalkowski.
3) Add capability to export the XDP features supported by the NIC.
Along with that, add a XDP compliance test tool,
from Lorenzo Bianconi & Marek Majtyka.
4) Add __bpf_kfunc tag for marking kernel functions as kfuncs,
from David Vernet.
5) Add a deep dive documentation about the verifier's register
liveness tracking algorithm, from Eduard Zingerman.
6) Fix and follow-up cleanups for resolve_btfids to be compiled
as a host program to avoid cross compile issues,
from Jiri Olsa & Ian Rogers.
7) Batch of fixes to the BPF selftest for xdp_hw_metadata which resulted
when testing on different NICs, from Jesper Dangaard Brouer.
8) Fix libbpf to better detect kernel version code on Debian, from Hao Xiang.
9) Extend libbpf to add an option for when the perf buffer should
wake up, from Jon Doron.
10) Follow-up fix on xdp_metadata selftest to just consume on TX
completion, from Stanislav Fomichev.
11) Extend the kfuncs.rst document with description on kfunc
lifecycle & stability expectations, from David Vernet.
12) Fix bpftool prog profile to skip attaching to offline CPUs,
from Tonghao Zhang.
====================
Link: https://lore.kernel.org/r/20230211002037.8489-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current taprio software implementation is haunted by the shadow of the
igb/igc hardware model. It iterates over child qdiscs in increasing
order of TXQ index, therefore giving higher xmit priority to TXQ 0 and
lower to TXQ N. According to discussions with Vinicius, that is the
default (perhaps even unchangeable) prioritization scheme used for the
NICs that taprio was first written for (igb, igc), and we have a case of
two bugs canceling out, resulting in a functional setup on igb/igc, but
a less sane one on other NICs.
To the best of my understanding, taprio should prioritize based on the
traffic class, so it should really dequeue starting with the highest
traffic class and going down from there. We get to the TXQ using the
tc_to_txq[] netdev property.
TXQs within the same TC have the same (strict) priority, so we should
pick from them as fairly as we can. We can achieve that by implementing
something very similar to q->curband from multiq_dequeue().
Since igb/igc really do have TXQ 0 of higher hardware priority than
TXQ 1 etc, we need to preserve the behavior for them as well. We really
have no choice, because in txtime-assist mode, taprio is essentially a
software scheduler towards offloaded child tc-etf qdiscs, so the TXQ
selection really does matter (not all igb TXQs support ETF/SO_TXTIME,
says Kurt Kanzenbach).
To preserve the behavior, we need a capability bit so that taprio can
determine if it's running on igb/igc, or on something else. Because igb
doesn't offload taprio at all, we can't piggyback on the
qdisc_offload_query_caps() call from taprio_enable_offload(), but
instead we need a separate call which is also made for software
scheduling.
Introduce two static keys to minimize the performance penalty on systems
which only have igb/igc NICs, and on systems which only have other NICs.
For mixed systems, taprio will have to dynamically check whether to
dequeue using one prioritization algorithm or using the other.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A summary of the flags being set for various drivers is given below.
Note that XDP_F_REDIRECT_TARGET and XDP_F_FRAG_TARGET are features
that can be turned off and on at runtime. This means that these flags
may be set and unset under RTNL lock protection by the driver. Hence,
READ_ONCE must be used by code loading the flag value.
Also, these flags are not used for synchronization against the availability
of XDP resources on a device. It is merely a hint, and hence the read
may race with the actual teardown of XDP resources on the device. This
may change in the future, e.g. operations taking a reference on the XDP
resources of the driver, and in turn inhibiting turning off this flag.
However, for now, it can only be used as a hint to check whether device
supports becoming a redirection target.
Turn 'hw-offload' feature flag on for:
- netronome (nfp)
- netdevsim.
Turn 'native' and 'zerocopy' features flags on for:
- intel (i40e, ice, ixgbe, igc)
- mellanox (mlx5).
- stmmac
- netronome (nfp)
Turn 'native' features flags on for:
- amazon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2, enetc)
- funeth
- intel (igb)
- marvell (mvneta, mvpp2, octeontx2)
- mellanox (mlx4)
- mtk_eth_soc
- qlogic (qede)
- sfc
- socionext (netsec)
- ti (cpsw)
- tap
- tsnep
- veth
- xen
- virtio_net.
Turn 'basic' (tx, pass, aborted and drop) features flags on for:
- netronome (nfp)
- cavium (thunder)
- hyperv.
Turn 'redirect_target' feature flag on for:
- amanzon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2)
- intel (i40e, ice, igb, ixgbe)
- ti (cpsw)
- marvell (mvneta, mvpp2)
- sfc
- socionext (netsec)
- qlogic (qede)
- mellanox (mlx5)
- tap
- veth
- virtio_net
- xen
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Co-developed-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Marek Majtyka <alardam@gmail.com>
Link: https://lore.kernel.org/r/3eca9fafb308462f7edb1f58e451d59209aa07eb.1675245258.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this doesn't control interrupt generation by the Root Port; that
is controlled by the AER Root Error Command register, which is managed by
the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When a MAC address is not assigned to the VF, that portion of the message
sent to the VF is not set. The memory, however, is allocated from the
stack meaning that information may be leaked to the VM. Initialize the
message buffer to 0 so that no information is passed to the VM in this
case.
Fixes: 6ddbc4cf1f ("igb: Indicate failure on vf reset for empty mac address")
Reported-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221212190031.3983342-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Without this change, the interrupt test fail with MSI-X environment:
$ sudo ethtool -t enp0s2 offline
[ 43.921783] igb 0000:00:02.0: offline testing starting
[ 44.855824] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Down
[ 44.961249] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 51.272202] igb 0000:00:02.0: testing shared interrupt
[ 56.996975] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
The test result is FAIL
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 4
Loopback test (offline) 0
Link test (on/offline) 0
Here, "4" means an expected interrupt was not delivered.
To fix this, route IRQs correctly to the first MSI-X vector by setting
IVAR_MISC. Also, set bit 0 of EIMS so that the vector will not be
masked. The interrupt test now runs properly with this change:
$ sudo ethtool -t enp0s2 offline
[ 42.762985] igb 0000:00:02.0: offline testing starting
[ 50.141967] igb 0000:00:02.0: testing shared interrupt
[ 56.163957] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
The test result is PASS
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 0
Fixes: 4eefa8f013 ("igb: add single vector msi-x testing to interrupt test")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation for removing the "silently change allocation size"
users of ksize(), explicitly round up all q_vector allocations so that
allocations can be correctly compared to ksize().
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Avoid potential use-after-free condition under memory pressure. If the
kzalloc() fails, q_vector will be freed but left in the original
adapter->q_vector[v_idx] array position.
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Many drivers implement the .adjfreq or .adjfine PTP op function with the
same basic logic:
1. Determine a base frequency value
2. Multiply this by the abs() of the requested adjustment, then divide by
the appropriate divisor (1 billion, or 65,536 billion).
3. Add or subtract this difference from the base frequency to calculate a
new adjustment.
A few drivers need the difference and direction rather than the combined
new increment value.
I recently converted the Intel drivers to .adjfine and the scaled parts per
million (65.536 parts per billion) logic. To avoid overflow with minimal
loss of precision, mul_u64_u64_div_u64 was used.
The basic logic used by all of these drivers is very similar, and leads to
a lot of duplicate code to perform the same task.
Rather than keep this duplicate code, introduce diff_by_scaled_ppm and
adjust_by_scaled_ppm. These helper functions calculate the difference or
adjustment necessary based on the scaled parts per million input.
The diff_by_scaled_ppm function returns true if the difference should be
subtracted, and false otherwise.
Update the Intel drivers to use the new helper functions. Other vendor
drivers will be converted to .adjfine and this helper function in the
following changes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw
Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool
Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5}
Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena
Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet
Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit c23d92b80e ("igb: Teardown SR-IOV before
unregister_netdev()") places the unregister_netdev() call after the
igb_disable_sriov() call to avoid functionality issue.
However, it introduces several race conditions when detaching a device.
For example, when .remove() is called, the below interleaving leads to
use-after-free.
(FREE from device detaching) | (USE from netdev core)
igb_remove | igb_ndo_get_vf_config
igb_disable_sriov | vf >= adapter->vfs_allocated_count?
kfree(adapter->vf_data) |
adapter->vfs_allocated_count = 0 |
| memcpy(... adapter->vf_data[vf]
Moreover, the igb_disable_sriov() also suffers from data race with the
requests from VF driver.
(FREE from device detaching) | (USE from requests)
igb_remove | igb_msix_other
igb_disable_sriov | igb_msg_task
kfree(adapter->vf_data) | vf < adapter->vfs_allocated_count
adapter->vfs_allocated_count = 0 |
To this end, this commit first eliminates the data races from netdev
core by using rtnl_lock (similar to commit 7194792308 ("dpaa2-eth: add
MAC/PHY support through phylink")). And then adds a spinlock to
eliminate races from driver requests. (similar to commit 1e53834ce5
("ixgbe: Add locking to prevent panic when setting sriov_numvfs to zero")
Fixes: c23d92b80e ("igb: Teardown SR-IOV before unregister_netdev()")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220817184921.735244-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 82576 PTP implementation still uses .adjfreq instead of using the newer
.adjfine.
This implementation uses a pre-simplified calculation since the base
increment value for the 82576 is just 16 * 2^19. Converting this into
scaled_ppm is tricky, and makes the intent a bit less clear.
Simply convert to the normal flow of multiplying the base increment value
by the scaled_ppm and then dividing by 1000000ULL << 16. This can be
implemented using mul_u64_u64_div_u64 which can avoid the possible overflow
that might occur for large adjustments.
Use of .adjfine can improve the precision of small adjustments and gets us
one driver closer to removing the old implementation from the kernel
entirely.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the capability to map non-linear xdp frames in XDP_TX and
ndo_xdp_xmit callback.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220711230751.3124415-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Delete the redundant word 'frames'.
Delete the redundant word 'set'.
Delete the redundant word 'slot'.
Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
there is an unexpected word "the" in the comments that need to be removed
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps
Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which
will be significantly lower when 1) ASPM is disabled or 2) SoC package
c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx
speed can reach to ~950Mbps.
According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC",
"DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so
set it to 1b for "DMA is considered idle when there is no Rx or Tx AND
when there are no TLPs indicating that CPU is active detected on the
PCIe link (such as the host executes CSR or Configuration register read
or write operation)" and performing Tx should also fall under "active
CPU on PCIe link" case.
In addition to that, commit b6e0c419f0 ("igb: Move DMA Coalescing init
code to separate function.") seems to wrongly changed from enabling
E1000_PCIEMISC_LX_DECISION to disabling it, also fix that.
Fixes: b6e0c419f0 ("igb: Move DMA Coalescing init code to separate function.")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220621221056.604304-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's no need to define same thing twice.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
igb_read_phy_reg() will silently return, leaving phy_data untouched, if
hw->ops.read_reg isn't set. Depending on the uninitialized value of
phy_data, this led to the phy status check either succeeding immediately
or looping continuously for 2 seconds before emitting a noisy err-level
timeout. This message went out to the console even though there was no
actual problem.
Instead, first check if there is read_reg function pointer. If not,
proceed without trying to check the phy status register.
Fixes: b72f3f7200 ("igb: When GbE link up, wait for Remote receiver status condition")
Signed-off-by: Kevin Mitchell <kevmitch@arista.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmap() is being deprecated and these usages are all local to the thread
so there is no reason kmap_local_page() can't be used.
Replace kmap() calls with kmap_local_page().
Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Clang static analysis reports this representative issue
igb_ptp.c:997:3: warning: The left operand of '+' is a
garbage value
ktime_add_ns(shhwtstamps.hwtstamp, adjust);
^ ~~~~~~~~~~~~~~~~~~~~
shhwtstamps.hwtstamp is set by a call to
igb_ptp_systim_to_hwtstamp(). In the switch-statement
for the hw type, the hwtstamp is zeroed for matches
but not the default case. Move the memset out of
switch-statement. This degarbages the default case
and reduces the size.
Some whitespace cleanup of empty lines
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
On changing the RX ring parameters igb uses a hack to avoid a warning
when calling xdp_rxq_info_reg via igb_setup_rx_resources. It just
clears the struct xdp_rxq_info content.
Instead, change this to unregister if we're already registered. Align
code to the igc code.
Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So, if dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be
1.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for the PTP pin function on 82580/i354/i350 based adapters.
Because the time registers of these adapters do not have the nice split in
second rollovers as the i210 has, the implementation is slightly more
complex compared to the i210 implementation.
Signed-off-by: Ruud Bos <kernel.hbk@gmail.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Support for the PEROUT PTP pin function on 82580/i354/i350 based adapters.
Because the time registers of these adapters do not have the nice split in
second rollovers as the i210 has, the implementation is slightly more
complex compared to the i210 implementation.
Signed-off-by: Ruud Bos <kernel.hbk@gmail.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove code duplication in the tsync interrupt handler function by moving
this logic to separate functions. This keeps the interrupt handler readable
and allows the new functions to be extended for adapter types other than
i210.
Signed-off-by: Ruud Bos <kernel.hbk@gmail.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Allow reuse of SDP config struct initialization by moving it to a
separate function.
Signed-off-by: Ruud Bos <kernel.hbk@gmail.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
igb driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The variable used for return status in `igb_write_xmdio_reg' function
is never changed and this function is just need return 0. Thus, the
`ret_val' can be removed and return 0 at the end of the
`igb_write_xmdio_reg' function.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Recent net core changes caused an issue with few Intel drivers
(reportedly igb), where taking RTNL in RPM resume path results in a
deadlock. See [0] for a bug report. I don't think the core changes
are wrong, but taking RTNL in RPM resume path isn't needed.
The Intel drivers are the only ones doing this. See [1] for a
discussion on the issue. Following patch changes the RPM resume path
to not take RTNL.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=215129
[1] https://lore.kernel.org/netdev/20211125074949.5f897431@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com/t/
Fixes: bd869245a3 ("net: core: try to runtime-resume detached device in __dev_open")
Fixes: f32a213765 ("ethtool: runtime-resume netdev parent before ethtool ioctl ops")
Tested-by: Martin Stolpe <martin.stolpe@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20211220201844.2714498-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move checking condition of VF MAC filter before clearing
or adding MAC filter to VF to prevent potential blackout caused
by removal of necessary and working VF's MAC filter.
Fixes: 1b8b062a99 ("igb: add VF trust infrastructure")
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since commit 94dd016ae5 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In non trivial scenarios, the action id alone is not sufficient to
identify the program causing the warning. Before the previous patch,
the generated stack-trace pointed out at least the involved device
driver.
Let's additionally include the program name and id, and the relevant
device name.
If the user needs additional infos, he can fetch them via a kernel
probe, leveraging the arguments added here.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/ddb96bb975cbfddb1546cf5da60e77d5100b533c.1638189075.git.pabeni@redhat.com
Oleksandr brought a bug report where netpoll causes trace
messages in the log on igb.
Danielle brought this back up as still occurring, so we'll try
again.
[22038.710800] ------------[ cut here ]------------
[22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll
[22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0
As Alex suggested, change the driver to return work_done at the
exit of napi_poll, which should be safe to do in this driver
because it is not polling multiple queues in this single napi
context (multiple queues attached to one MSI-X vector). Several
other drivers contain the same simple sequence, so I hope
this will not create new problems.
Fixes: 16eb8815c2 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Danielle Ratson <danieller@nvidia.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In following patches, dev_watchdog() will no longer stop all queues.
It will read queue->trans_start locklessly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver tried to use Linux' native software I2C bus master
(i2c-algo-bits) for exporting the I2C interface that talks to the SFP
cage(s) towards userspace. As-is, however, the physical SCL/SDA pins
were not moving at all, staying at logical 1 all the time.
The main culprit was the I2CPARAMS register where igb was not setting
the I2CBB_EN bit. That meant that all the careful signal bit-banging was
actually not being propagated to the chip pads (I verified this with a
scope).
The bit-banging was not correct either, because I2C is supposed to be an
open-collector bus, and the code was driving both lines via a totem
pole. The code was also trying to do operations which did not make any
sense with the i2c-algo-bits, namely manipulating both SDA and SCL from
igb_set_i2c_data (which is only supposed to set SDA). I'm not sure if
that was meant as an optimization, or was just flat out wrong, but given
that the i2c-algo-bits is set up to work with a totally dumb GPIO-ish
implementation underneath, there's no need for this code to be smart.
The open-drain vs. totem-pole is fixed by the usual trick where the
logical zero is implemented via regular output mode and outputting a
logical 0, and the logical high is implemented via the IO pad configured
as an input (thus floating), and letting the mandatory pull-up resistors
do the rest. Anything else is actually wrong on I2C where all devices
are supposed to have open-drain connection to the bus.
The missing I2CBB_EN is set (along with a safe initial value of the
GPIOs) just before registering this software I2C bus.
The chip datasheet mentions HW-implemented I2C transactions (SFP EEPROM
reads and writes) as well, but I'm not touching these for simplicity.
Tested on a LR-Link LRES2203PF-2SFP (which is an almost-miniPCIe form
factor card, a cable, and a module with two SFP cages). There was one
casualty, an old broken SFP we had laying around, which was used to
solder some thin wires as a DIY I2C breakout. Thanks for your service.
With this patch in place, I can `i2cdump -y 3 0x51 c` and read back data
which make sense. Yay.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
See-also: https://www.spinics.net/lists/netdev/msg490554.html
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Convert all Ethernet drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
In theory addr_len may not be ETH_ALEN, but we don't expect
non-Ethernet devices to live under this directory, and only
the following cases of setting addr_len exist:
- cxgb4 for mgmt device,
and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add failed_counter to i21x_doublecheck(). There is possibility that
loop will never end.
With this patch the loop will stop after maximum 3 retries
to write to MTA_REGISTER
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Assignment to *ring should be done after correctness check of the
argument queue.
Fixes: 91db364236 ("igb: Refactor igb_configure_cbs()")
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ensure that the adapter->q_vector[MAX_Q_VECTORS] array isn't accessed
beyond its size. It was fixed by using a local variable num_q_vectors
as a limit for loop index, and ensure that num_q_vectors is not bigger
than MAX_Q_VECTORS.
Fixes: 047e0030f1 ("igb: add new data structure for handling interrupts and NAPI")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Slawomir Laba <slawomirx.laba@intel.com>
Reviewed-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Reviewed-by: Mateusz Palczewski <mateusz.placzewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 40a914fa72 ("igb: Add support for pci-e Advanced Error Reporting")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Cleans the next descriptor to watch (next_to_watch) when cleaning the
TX ring.
Failure to do so can cause invalid memory accesses. If igb_poll() runs
while the controller is reset this can lead to the driver try to free
a skb that was already freed.
(The crash is harder to reproduce with the igb driver, but the same
potential problem exists as the code is identical to igc)
Fixes: 7cc6fd4c60 ("igb: Don't bother clearing Tx buffer_info in igb_clean_tx_ring")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reported-by: Erez Geva <erez.geva.ext@siemens.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The Intel drivers all have rcu_read_lock()/rcu_read_unlock() pairs around
XDP program invocations. However, the actual lifetime of the objects
referred by the XDP program invocation is longer, all the way through to
the call to xdp_do_flush(), making the scope of the rcu_read_lock() too
small. This turns out to be harmless because it all happens in a single
NAPI poll cycle (and thus under local_bh_disable()), but it makes the
rcu_read_lock() misleading.
Rather than extend the scope of the rcu_read_lock(), just get rid of it
entirely. With the addition of RCU annotations to the XDP_REDIRECT map
types that take bh execution into account, lockdep even understands this to
be safe, so there's really no reason to keep it around.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com> # i40e
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Link: https://lore.kernel.org/bpf/20210624160609.292325-12-toke@redhat.com
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.
Fixes: 9cbc948b5a ("igb: add XDP support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When using native XDP with the igb driver, the XDP frame data doesn't point to
the beginning of the packet. It's off by 16 bytes. Everything works as expected
with XDP skb mode.
Actually these 16 bytes are used to store the packet timestamps. Therefore, pull
the timestamp before executing any XDP operations and adjust all other code
accordingly. The igc driver does it like that as well.
Tested with Intel i210 card and AF_XDP sockets.
Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If CONFIG_IGB_HWMON is n, gcc warns:
drivers/net/ethernet/intel/igb/e1000_82575.c:2765:17:
warning: ‘e1000_emc_therm_limit’ defined but not used [-Wunused-const-variable=]
static const u8 e1000_emc_therm_limit[4] = {
^~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/igb/e1000_82575.c:2759:17:
warning: ‘e1000_emc_temp_data’ defined but not used [-Wunused-const-variable=]
static const u8 e1000_emc_temp_data[4] = {
^~~~~~~~~~~~~~~~~~~
Move it into #ifdef block to fix this.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb PTP code was using htons() on a constant to try to
byte swap the value before writing it to a register. This byte
swap has the consequence of triggering sparse conflicts between
the register write which expect cpu ordered input, and the code
which generated a big endian constant. Just override the cast
to make sure code doesn't change but silence the warning.
Can't do a __swab16 in this case because big endian systems
would then write the wrong value.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The igb driver was trying hard to be sparse correct, but somehow
ended up converting a variable into little endian order and then
tries to OR something with it.
A much plainer way of doing things is to leave all variables and
OR operations in CPU (non-endian) mode, and then convert to
little endian only once, which is what this change does.
This probably fixes a bug that might have been seen only on
big endian systems.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The sparse build (C=2) finds some issues with how the driver
dealt with the (very difficult) hardware that in some generations
uses little-endian, and in others uses big endian, for the VLAN
field. The code as written picks __le16 as a type and for some
hardware revisions we override it to __be16 as done in this
patch. This impacted the VF driver as well so fix it there too.
Also change the vlan_tci assignment to override the sparse
warning without changing functionality.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The igb and igc driver both use a trick of creating a local type
pointer on the stack to ease dealing with a receive descriptor in
64 bit chunks for printing. Sparse however was not taken into
account and receive descriptors are always in little endian
order, so just make the unions use __le64 instead of u64.
No functional change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The sparse checker (C=2) found an assignment where we were mixing
types when trying to convert from data read directly from the
device NVM, to an array in CPU order in-memory, which
unfortunately the driver tries to do in-place.
This is easily solved by using the swap operation instead of an
assignment, and is already proven in other Intel drivers to be
functionally correct and the same code, just without a sparse
warning.
The change is the same in all three drivers.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new function which checks MTA_REGISTER if its filled correctly.
If not then writes again to same register.
There is possibility that i210 and i211 could not accept
MTA_REGISTER settings, specially when you add and remove
many of multicast addresses in short time.
Without this patch there is possibility that multicast settings will be
not always set correctly in hardware.
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i210 has a total of 24KB of transmit packet buffer. When in Qav mode,
this buffer is divided into four pieces, one for each Tx queue.
Currently, 8KB are given to each of the two SR queues and 4KB are given
to each of the two SP queues.
However, it was noticed that such distribution can make best effort
traffic (which would usually go to the SP queues when Qav is enabled, as
the SR queues would be used by ETF or CBS qdiscs for TSN-aware traffic)
perform poorly. Using iperf3 to measure, one could see the performance
of best effort traffic drop by nearly a third (from 935Mbps to 578Mbps),
with no TSN traffic competing.
This patch redistributes the 24KB to each queue equally: 6KB each. On
tests, there was no notable performance reduction of best effort traffic
performance when there was no TSN traffic competing.
Below, more details about the data collected:
All experiments were run using the following qdisc setup:
qdisc taprio 100: root refcnt 9 tc 4 map 3 3 3 2 3 0 0 3 3 3 3 3 3 3 3 3
queues offset 0 count 1 offset 1 count 1 offset 2 count 1 offset 3 count 1
clockid TAI base-time 0 cycle-time 10000000 cycle-time-extension 0
index 0 cmd S gatemask 0xf interval 10000000
qdisc etf 8045: parent 100:1 clockid TAI delta 1000000 offload on
deadline_mode off skip_sock_check off
TSN traffic, when enabled, had this characteristics:
Packet size: 1500 bytes
Transmission interval: 125us
----------------------------------
Without this patch:
----------------------------------
- TCP data:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.35 GBytes 578 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.07 GBytes 460 Mbits/sec 1
- TCP data limiting iperf3 buffer size to 4K:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.35 GBytes 579 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.08 GBytes 462 Mbits/sec 0
- TCP data limiting iperf3 buffer size to 192 bytes (smallest size without
serious performance degradation):
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.34 GBytes 577 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.07 GBytes 461 Mbits/sec 1
- UDP data at 1000Mbit/sec:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 1.36 GBytes 586 Mbits/sec 0.000 ms 0/1011407 (0%)
- With TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 1.05 GBytes 451 Mbits/sec 0.000 ms 0/778672 (0%)
----------------------------------
With this patch:
----------------------------------
- TCP data:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 2.17 GBytes 932 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.50 GBytes 646 Mbits/sec 1
- TCP data limiting iperf3 buffer size to 4K:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 2.17 GBytes 931 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.50 GBytes 645 Mbits/sec 0
- TCP data limiting iperf3 buffer size to 192 bytes (smallest size without
serious performance degradation):
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 2.17 GBytes 932 Mbits/sec 1
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.50 GBytes 645 Mbits/sec 0
- UDP data at 1000Mbit/sec:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 2.23 GBytes 956 Mbits/sec 0.000 ms 0/1650226 (0%)
- With TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 1.51 GBytes 649 Mbits/sec 0.000 ms 0/1120264 (0%)
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-03-24
The following pull-request contains BPF updates for your *net-next* tree.
We've added 37 non-merge commits during the last 15 day(s) which contain
a total of 65 files changed, 3200 insertions(+), 738 deletions(-).
The main changes are:
1) Static linking of multiple BPF ELF files, from Andrii.
2) Move drop error path to devmap for XDP_REDIRECT, from Lorenzo.
3) Spelling fixes from various folks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of just
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
A bunch of header comments were showing warnings when compiling
with W=1. Fix them all at once. This changes only comments.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a couple of checks to make sure timestamping is on and that the
timestamp value from DMA is valid. This avoids any functional issues
that could come from a misinterpreted time stamp.
One of the functions changed doesn't need a return value added because
there was no value in checking from the calling locations.
While here, fix a couple of reverse christmas tree issues next to
the code being changed.
Fixes: f56e7bba22 ("igb: Pull timestamp from fragment before adding it to skb")
Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The include guard "_E1000_HW_H_" is used by two separate header files in
two different drivers (e1000/e1000_hw.h and igb/e1000_hw.h). Using the
same include guard macro in more than one header file may cause
unexpected behavior from the compiler. Fix this by renaming the
duplicate guard in the igb driver.
Fixes: 9d5c824399 ("igb: PCI-Express 82575 Gigabit Ethernet driver")
Signed-off-by: Tom Seewald <tseewald@gmail.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We want to change the current ndo_xdp_xmit drop semantics because it will
allow us to implement better queue overflow handling. This is working
towards the larger goal of a XDP TX queue-hook. Move XDP_REDIRECT error
path handling from each XDP ethernet driver to devmap code. According to
the new APIs, the driver running the ndo_xdp_xmit pointer, will break tx
loop whenever the hw reports a tx error and it will just return to devmap
caller the number of successfully transmitted frames. It will be devmap
responsibility to free dropped frames.
Move each XDP ndo_xdp_xmit capable driver to the new APIs:
- veth
- virtio-net
- mvneta
- mvpp2
- socionext
- amazon ena
- bnxt
- freescale (dpaa2, dpaa)
- xen-frontend
- qede
- ice
- igb
- ixgbe
- i40e
- mlx5
- ti (cpsw, cpsw-new)
- tun
- sfc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/bpf/ed670de24f951cfd77590decf0229a0ad7fd12f6.1615201152.git.lorenzo@kernel.org
Update the Intel drivers to make use of ethtool_sprintf. The general idea
is to reduce code size and overhead by replacing the repeated pattern of
string printf statements and ETH_STRING_LEN counter increments.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/structue/structure/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igb needs a similar fix as commit 75aab4e10a ("i40e: avoid
premature Rx buffer reuse")
The page recycle code, incorrectly, relied on that a page fragment
could not be freed inside xdp_do_redirect(). This assumption leads to
that page fragments that are used by the stack/XDP redirect can be
reused and overwritten.
To avoid this, store the page count prior invoking xdp_do_redirect().
Longer explanation:
Intel NICs have a recycle mechanism. The main idea is that a page is
split into two parts. One part is owned by the driver, one part might
be owned by someone else, such as the stack.
t0: Page is allocated, and put on the Rx ring
+---------------
used by NIC ->| upper buffer
(rx_buffer) +---------------
| lower buffer
+---------------
page count == USHRT_MAX
rx_buffer->pagecnt_bias == USHRT_MAX
t1: Buffer is received, and passed to the stack (e.g.)
+---------------
| upper buff (skb)
+---------------
used by NIC ->| lower buffer
(rx_buffer) +---------------
page count == USHRT_MAX
rx_buffer->pagecnt_bias == USHRT_MAX - 1
t2: Buffer is received, and redirected
+---------------
| upper buff (skb)
+---------------
used by NIC ->| lower buffer
(rx_buffer) +---------------
Now, prior calling xdp_do_redirect():
page count == USHRT_MAX
rx_buffer->pagecnt_bias == USHRT_MAX - 2
This means that buffer *cannot* be flipped/reused, because the skb is
still using it.
The problem arises when xdp_do_redirect() actually frees the
segment. Then we get:
page count == USHRT_MAX - 1
rx_buffer->pagecnt_bias == USHRT_MAX - 2
From a recycle perspective, the buffer can be flipped and reused,
which means that the skb data area is passed to the Rx HW ring!
To work around this, the page count is stored prior calling
xdp_do_redirect().
Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As explained in commit 29d98f54a4 ("net: enetc: allow hardware
timestamping on TX queues with tc-etf enabled"), hardware TX
timestamping requires an skb with skb->tstamp = 0. When a packet is sent
with SO_TXTIME, the skb->skb_mstamp_ns corrupts the value of skb->tstamp,
so the drivers need to explicitly reset skb->tstamp to zero after
consuming the TX time.
Create a helper named skb_txtime_consumed() which does just that. All
drivers which offload TC_SETUP_QDISC_ETF should implement it, and it
would make it easier to assess during review whether they do the right
thing in order to be compatible with hardware timestamping or not.
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-02-03
This series contains updates to igc, igb, e1000e, and e1000 drivers.
Sasha adds counting of good transmit packets and reporting of NVM version
and gPHY version in ethtool firmware version. Replaces the use of strlcpy
to the preferred strscpy. Fixes a typo that caused the wrong register to be
output. He also removes an unused function pointer, some unneeded defines,
and a non-applicable comment. All changes for igc.
Gal Hammer fixes a typo which caused the RDBAL register values to be
shown instead of TDBAL for igb.
Nick Lowe enables RSS support for i211 devices for igb.
Tom Rix fixes checkpatch warning by removing h from printk format
specifier for igb.
Kaixu Xia removes setting of a variable that is overwritten before next
use for e1000e.
Sudip Mukherjee removes an unneeded assignment for e1000.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
e1000: drop unneeded assignment in e1000_set_itr()
e1000e: remove the redundant value assignment in e1000_update_nvm_checksum_spt
igb: remove h from printk format specifier
igb: Enable RSS for Intel I211 Ethernet Controller
igb: fix TDBAL register show incorrect value
igc: Fix TDBAL register show incorrect value
igc: Remove unused FUNC_1 mask
igc: Remove unused local receiver mask
igc: Prefer strscpy over strlcpy
igc: Expose the gPHY firmware version
igc: Expose the NVM version
igc: Add Host Good Packets Transmitted Count
igc: Remove MULR mask define
igc: Remove igc_set_fw_version comment
igc: Clean up nvm_operations structure
====================
Link: https://lore.kernel.org/r/20210204004259.3662059-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now we can remove a bunch of identical functions from the drivers and
make them use common dev_page_is_reusable(). All {,un}likely() checks
are omitted since it's already present in this helper.
Also update some comments near the call sites.
Suggested-by: David Rientjes <rientjes@google.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This change fixes the checkpatch warning described in this
commit cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")
Standard integer promotion is already done and %hx and %hhx is useless
so do not encourage the use of %hh[xudi] or %h[xudi].
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The Intel I211 Ethernet Controller supports 2 Receive Side Scaling (RSS)
queues. It should not be excluded from having this feature enabled.
Via commit c883de9fd7 ("igb: rename igb define to be more generic")
E1000_MRQC_ENABLE_RSS_4Q was renamed to E1000_MRQC_ENABLE_RSS_MQ to
indicate that this is a generic bit flag to enable queues and not
a flag that is specific to devices that support 4 queues
The bit flag enables 2, 4 or 8 queues appropriately depending on the part.
Tested with a multicore CPU and frames were then distributed as expected.
This issue appears to have been introduced because of confusion caused
by the prior name.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Tested-by: David Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fixed a typo which caused the registers dump function to read the
RDBAL register when printing TDBAL register values.
Signed-off-by: Gal Hammer <ghammer@redhat.com>
Tested-by: David Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Using skb_csum_is_sctp is a easier way to validate it's a SCTP
CRC checksum offload packet, and there is no need to parse the
packet to check its proto field, especially when it's a UDP or
GRE encapped packet.
So this patch also makes igb support SCTP CRC checksum offload
for UDP and GRE encapped packets.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since we share the transmit queue with the network stack,
it is possible that we run into a transmit queue timeout.
This will reset the queue.
This happens under high load when XDP is using the
transmit queue pretty much exclusively.
netdev_start_xmit() sets the trans_start variable of the
transmit queue to jiffies which is later utilized by dev_watchdog(),
so to avoid timeout, let stack know that XDP xmit happened by
bumping the trans_start within XDP Tx routines to jiffies.
Fixes: 9cbc948b5a ("igb: add XDP support")
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since it is a new XDP implementation change xdp_do_flush_map
to xdp_do_flush.
Fixes: 9cbc948b5a ("igb: add XDP support")
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
add metasize if it is set in xdp
Fixes: 9cbc948b5a ("igb: add XDP support")
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add an extack error message when the RX buffer size is too small
for the frame size.
Fixes: 9cbc948b5a ("igb: add XDP support")
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Increase the packet header padding to include double VLAN tagging.
This patch uses a macro for this.
Fixes: 9cbc948b5a ("igb: add XDP support")
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The igb XDP xmit back function should only return
defined error codes.
Fixes: 9cbc948b5a ("igb: add XDP support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add napi_id to the xdp_rxq_info structure, and make sure the XDP
socket pick up the napi_id in the Rx path. The napi_id is used to find
the corresponding NAPI structure for socket busy polling.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/bpf/20201130185205.196029-7-bjorn.topel@gmail.com
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and a tree wide
effort to clean up and consolidate the (ab)usage of in_interrupt() and
related checks is happening.
In this case the checks cover only parts of the contexts in which these
functions cannot be called. They fail to detect preemption or interrupt
disabled invocations.
As the functions which are invoked from the various places contain already
a broad variety of checks (always enabled or debug option dependent) cover
all invalid conditions already, there is no point in having inconsistent
warnings in those drivers.
Just remove them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed flash presence check for 82576 controllers so the part
number string is read and displayed correctly.
Signed-off-by: Gal Hammer <ghammer@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add XDP support to the IGB driver.
The implementation follows the IXGBE XDP implementation
closely and I used the following patches as basis:
1. commit 9247080816 ("ixgbe: add XDP support for pass and drop actions")
2. commit 33fdc82f08 ("ixgbe: add support for XDP_TX action")
3. commit ed93a39871 ("ixgbe: tweak page counting for XDP_REDIRECT")
Due to the hardware constraints of the devices using the
IGB driver we must share the TX queues with XDP which
means locking the TX queue for XDP.
I ran tests on an older device to get better numbers.
Test machine:
Intel(R) Atom(TM) CPU C2338 @ 1.74GHz (2 Cores)
2x Intel I211
Routing Original Driver Network Stack: 382 Kpps
Routing XDP Redirect (xdp_fwd_kern): 1.48 Mpps
XDP Drop: 1.48 Mpps
Using XDP we can achieve line rate forwarding even on
an older Intel Atom CPU.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
