[Why]
The call currently does two things:
1. Exits DMCUB from idle optimization if it was in
2. Checks DMCUB scratch register to determine if we need to call
DMCUB to do deferred HW restore and then sends the command if it's
ready for it.
By doing (1) we prevent driver idle from being renotified in the cases
where driver had previously allowed DC level idle optimizations via
dc_allow_idle_optimizations since it thinks:
allow == dc->idle_optimizations_allowed
...and that the operation is a no-op.
We want driver idle to be resent at the next opprotunity to do so
for video playback cases.
[How]
Migrate all usecases of dc_z10_restore to only perform (2).
Add extra calls to dc_allow_idle_optimizations to handle (1) and also
keep SW state matching with when we requested enter/exit of DMCUB
idle optimizations.
Ensure cursor idle optimizations false always get called when IPS
is supported.
Further rework/redesign is needed to decide whether we need a separate
level of DM allow vs DC allow and when to attempt re-entry.
Reviewed-by: Yihan Zhu <yihan.zhu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Enable the Panel Replay if eDP panel and ASIC support.
(prioritize Panel Replay over PSR)
[How]
- Setup the Panel Replay config during the device init
(prioritize Panel Replay over PSR).
- Separate the Replay init function into two functions
amdgpu_dm_link_setup_replay() and amdgpu_dm_set_replay_caps()
to fix the issue in the earlier commit that cause PSR and Replay
enabled at the same time.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Timings with small HBlank (such as CVT RBv2) can result in insufficient
HBlank bandwidth for audio SDP transmission when DSC is active. This
will cause some higher bandwidth audio modes to fail.
The combination of CVT RBv2 timings + DSC can commonly be encountered
in MST scenarios.
[How]
Add DP audio bandwidth validation for 8b/10b MST and 128b/132b SST/MST
cases and filter out modes that cannot be supported with the current
timing config.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
DML2 currently finds assigned pipes in array order rather than the
existing linked list order. This results in rearranging pipe order
on flip and more importantly otg inst and pipe idx mismatch.
This change preserves the order of existing pipes and guarantees
the head pipe will have matching otg inst and pipe idx.
Reviewed-by: Gabe Teeger <gabe.teeger@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- For some SKUs, the optimal DCFCLK for each UCLK is less than the
smallest DCFCLK STA target due to low memory bandwidth. There is
an assumption that the DCFCLK STA targets will always be less
than one of the optimal DCFCLK values, but this is not true for
SKUs that have low memory bandwidth. In this case we need to
populate the optimal UCLK for each DCFCLK STA targets as the max
UCLK freq.
- Also fix a bug in DML where start_state is not assigned and used
correctly.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Keep the same as previous APU and also insert clock dump
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
core_mode_programming in DML2 should output watermark calculations
to locals, but it incorrectly uses mode_lib
[How]
update code to match HW DML2
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Not clearing the memory select bits prior to OPTC disable can cause DSC
corruption issues when attempting to reuse a memory instance for another
OPTC that enables ODM.
[How]
Clear the memory select bits prior to disabling an OPTC.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SMU uses discrete dpp and disp clock levels. When we submit SMU request
for clock changes in Mhz we need to floor the requested value from Khz so
SMU will choose the next higher clock level in Khz to set. If we ceil to
Mhz, SMU will have to choose the next higher clock level after the ceil,
which could result in unnecessarily jumpping to the next level.
For example, we request 1911,111Khz which is exactly one of the SMU preset
level. If we pass 1912Mhz, SMU will choose 2150,000 khz. If we pass
1911Mhz, SMU will choose 1911,111kHz, which is the expected value.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can experience DENTIST hangs during optimize_bandwidth or TDRs if
FIFO is toggled and hangs.
[How]
Port the DCN35 fixes to DCN314.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When mapping resources, resources could be unavailable.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Theoretically, it would be possible for a buggy or malicious VBIOS to
overwrite past the bounds of the passed parameters (or its own
workspace); add bounds checking to prevent this from happening.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3093
Signed-off-by: Alexander Richards <electrodeyt@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Introduce a new Replay mode for DMUB version 0.0.199.0
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
res_pool is not initialized in all situations such as virtual
environments, and therefore link encoder resources should not be
initialized if res_pool is NULL.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add regkey to block video playback in IPS2 by default
Allow idle optimizations in the same spot we allow Replay for
video playback usecases.
Avoid sending it when there's an external display connected by
modifying the allow idle checks to check for active non-eDP screens.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In link_set_dsc_pps_packet(), 'struct display_stream_compressor *dsc'
was dereferenced in a DC_LOGGER_INIT(dsc->ctx->logger); before the 'dsc'
NULL pointer check.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/link_dpms.c:905 link_set_dsc_pps_packet() warn: variable dereferenced before check 'dsc' (see line 903)
Cc: stable@vger.kernel.org
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Wenjing Liu <wenjing.liu@amd.com>
Cc: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns (or errors with CONFIG_WERROR=y) when performing arithmetic
with different enumerated types, which is usually a bug:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_dpia_bw.c:548:24: error: arithmetic between different enumeration types ('const enum dc_link_rate' and 'const enum dc_lane_count') [-Werror,-Wenum-enum-conversion]
548 | link_cap->link_rate * link_cap->lane_count * LINK_RATE_REF_FREQ_IN_KHZ * 8;
| ~~~~~~~~~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~
1 error generated.
In this case, there is not a problem because the enumerated types are
basically treated as '#define' values. Add an explicit cast to an
integral type to silence the warning.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1976
Fixes: 5f3bce1326 ("drm/amd/display: Request usb4 bw for mst streams")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Improve z8/z10 support.
- Revert some of the VRR optimization.
- Improve usb4 when using MST.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Dpia hpd status not in sync causing driver not enabling BW Alloc after
S4.
[How]
Update hpd_status of the link when querying hpd state from dmub in
dpia_query_hpd_status().
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adjust z8 latency for performance.
Reviewed-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit d0f639c586.
The previous commit causes failure to light up for 1080p
eDP + 8k HDMI panel combo.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When usb4 bandwidth allocation mode is enabled, driver need to request
bandwidth from connection manager. For mst link, the requested
bandwidth should be big enough for all remote streams.
[HOW]
- If mst link, the requested bandwidth should be the sum of all mst
streams bandwidth added with dp MTPH overhead.
- Allocate/deallcate usb4 bandwidth when setting dpms on/off.
- When doing display mode validation, driver also need to consider total
bandwidth of all mst streams for mst link.
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Peichen Huang <peichen.huang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 6e4337f695.
The original commit causes regression in corner case with HDMI at
specific timings. Reverting from staging to get the full suite to
retest.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Martin Leung <martin.leung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 6b2b782ad6.
The original commit causes issues with certain features when DRR is
disabled, need to revisit this change later after resolving issues with
new DRR policy.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Martin Leung <martin.leung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If an OPP is used for a different OPTC without first being disconnected
from the previous OPTC, unexpected behaviour can occur. This also
applies to phantom pipes, which is what the current logic missed.
[How]
Disconnect OPPs from OPTC for phantom pipes before disabling OTG master.
Also move the disconnection to before the OTG master disable, since the
register is double buffered.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Panels show corruption with high refresh rate timings when ssc is
enabled.
[How]
Read down-spread percentage from lut to adjust dprefclk. Issues come
from S0i3 with this commit has been fixed by SMU.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Copy StutterPeriod from DML2 into DML1 StutterPeriod parameter.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
IGT `amdgpu/amd_color/crtc-lut-accuracy` fails right at the beginning of
the test execution, during atomic check, because DC rejects the
bandwidth state for a fb sizing 64x64. The test was previously working
with the deprecated dc_commit_state(). Now using
dc_validate_with_context() approach, the atomic check needs to perform a
full state validation. Therefore, set fast_validation to false in the
dc_validate_global_state call for atomic check.
Cc: stable@vger.kernel.org
Fixes: b8272241ff ("drm/amd/display: Drop dc_commit_state in favor of dc_commit_streams")
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These chips needs the same fix. This was previously not seen
on then since the AGP aperture expanded the system aperture,
but this showed up again when AGP was disabled.
Reviewed-and-tested-by: Jiadong Zhu <Jiadong.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Other environments don't like the unary minus operator on
an unsigned value.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Use tabs, not spaces.
- Brace and parentheses placement
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
gcc prints a warning about a possible array overflow for a couple of
callers of dp_decide_lane_settings() after commit 1b56c90018f0 ("Makefile:
Enable -Wstringop-overflow globally"):
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_fixed_vs_pe_retimer.c: In function 'dp_perform_fixed_vs_pe_training_sequence_legacy':
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_fixed_vs_pe_retimer.c:426:25: error: 'dp_decide_lane_settings' accessing 4 bytes in a region of size 1 [-Werror=stringop-overflow=]
426 | dp_decide_lane_settings(lt_settings, dpcd_lane_adjust,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
427 | lt_settings->hw_lane_settings, lt_settings->dpcd_lane_settings);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_fixed_vs_pe_retimer.c:426:25: note: referencing argument 4 of type 'union dpcd_training_lane[4]'
I'm not entirely sure what caused this, but changing the prototype to expect
a pointer instead of an array avoids the warnings.
Fixes: 7727e7b60f ("drm/amd/display: Improve robustness of FIXED_VS link training at DP1 rates")
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Place HDCP_EVENT_TRACE(hdcp, event) macro content inside do while loop
to avoid if-else issues in hdcp_log.h file
v2: fix up build (Alex)
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove braces for single statement if expressions and change comparison
order for hdcp2_execution.c file
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix identation inside enum and place expressions in define macros inside
() for hdcp_psp.h file
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove braces for single statement if expression for freesync.c file
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove braces from single statement if expression in hdcp1_execution.c
file
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
mod_freesync header file has duplicated copyright boilerplate. Drop the
duplicate.
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was included in gpu_info firmware, move it into the
driver for consistency with other nv1x parts.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2318
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The check for sending the vsc infopacket to the display was gated behind
PSR (Panel Self Refresh) being enabled.
The vsc infopacket also contains the colorimetry (specifically the
container color gamut) information for the stream on modern DP.
PSR is typically only supported on mobile phone eDP displays, thus this
was not getting sent for typical desktop monitors or TV screens.
This functionality is needed for proper HDR10 functionality on DP as it
wants BT2020 RGB/YCbCr for the container color space.
Cc: stable@vger.kernel.org
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Xaver Hugl <xaver.hugl@gmail.com>
Cc: Melissa Wen <mwen@igalia.com>
Fixes: 15f9dfd545 ("drm/amd/display: Register Colorspace property for DP and HDMI")
Tested-by: Simon Berz <simon@berz.me>
Tested-by: Xaver Hugl <xaver.hugl@kde.org>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following gcc with W=1:
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn35/dcn35_hwseq.c:1124: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Cc: Charlene Liu <charlene.liu@amd.com>
Cc: Muhammad Ahmed <ahmed.ahmed@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Srinath Rao <srinath.rao@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following gcc with W=1:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_state.c:524: warning: Function parameter or member 'state' not described in 'dc_state_rem_all_planes_for_stream'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_state.c:524: warning: Excess function parameter 'context' description in 'dc_state_rem_all_planes_for_stream'
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dmub_srv.c:540: warning: Function parameter or member 'context' not described in 'populate_subvp_cmd_drr_info'
Suggested-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Dillon Varone <dillon.varone@amd.com>
Cc: Jun Lei <jun.lei@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Srinath Rao <srinath.rao@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Prepare for enabling the Panel Replay feature
[HOW]
- Add some Panel Replay setting functions in DC
- Add the Panel Replay resource in dcn35_resource.c
- Add debug masks for Panel Replay
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 44e60b14d5.
Since, it causes a regression in which eDP displays with PSR support,
but no Replay support (Sink support <= 0x03), fail to enable PSR and
consequently all IGT amd_psr tests fail. So, revert this until a more
suitable fix can be found.
This got brought back accidently with the backmerge.
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Ivan Lipski <ivlipski@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For certain dual display configs that had one display using a 1080p
mode, the DPM level used to drive the configs regressed from DPM 0 to
DPM 3. This was caused by a missing check that should have only limited
the pipe segments on non-phantom pipes. This caused issues with detile
buffer allocation, which dissallow subvp from being used
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Relja Vojvodic <relja.vojvodic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A hang was observed where a read-modify-write access occurred due to the
register for idle state being shared between DMCUB and driver.
dmcub read - idle allow / no commit
driver read - idle allow / no commit
driver write - idle disallow / no commit
dmcub write - idle allow / commit
Resulting in DMCUB re-entering IPS after a disable and keeping the allow
high.
[How]
Long term we need to split commit/allow into two registers or use shared
DRAM state, but short term we can reduce the repro rate by ensuring that
the disallow went through by bounding the expected worst case scenario.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Failing mode validation during dc_commit, leading to blackscreen with an
8k DP2 display during mode change.
[What]
Fix mixmatch between pipe and stream, which prevented us from
recognizing the link as DP2.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Move all init files to hwss folder.
[how]
moved the dcnxx_init.c and .h files into inside the hwss and cleared the
linkage errors.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Revalla <hrevalla@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For FPO and SubVP/DRR cases we need to ensure to program
OTG_V_TOTAL_MIN/MAX_SEL, otherwise stretching the vblank in FPO / SubVP
/ DRR cases will not have any effect and we could hit underflow /
corruption.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If bandwidth allocation feature is enabled, connection manager wont
limit the dp tunnel bandwidth. So, need to do display mode validation
for streams on dpia links to avoid oversubscription of dp tunnel
bandwidth.
[How]
- To read non reduced link rate and lane count and update
reported link capability.
- To calculate the bandwidth required for streams of dpia links
per host router and validate against the allocated bandwidth for
the host router.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: PeiChen Huang <peichen.huang@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Race condition between notification of driver idle and the command being
processed. We could theoretically enter idle between the submission and
the wait for idle that occurs after.
[How]
Switch the notification to NO_WAIT to avoid the RPTR access.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If we time out waiting for PMFW to finish the exit sequence and touch
the DMCUB register the system will hang in a hard locked state.
[How]
Pol forever. This covers the case where things take too long but also
enables for debugging to occur since the cores won't be hardlocked.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc->idle_optimizations_allowed may be desynced with the hardware state.
[How]
Make sure we always exit out when dc_dmub_srv_exit_low_power_state is
called by removing the check.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some debug tools, sometimes wrap around to multiple lines which causes
issues with the DPM test script while it is looking for the logs. Need a
way to tell when the log is finished.
[How]
Added "LOG_END" to the end of the log.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Relja Vojvodic <relja.vojvodic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A new check was added to ensure FPO is not enabled when the FPO pipe has
0 planes. This requires the stream status to check the plane count, but
the stream status was not assigned for FPO + Vactive cases which leads
to FPO not be enabled always.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Relja Vojvodic <relja.vojvodic@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
link_rate sometime will be changed when DP MST connector hotplug, so
pbn_div also need be updated; otherwise, it will mismatch with
link_rate, causes no output in external monitor.
Cc: stable@vger.kernel.org
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Wade Wang <wade.wang@hp.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
BL1_PWM_USER_LEVEL is meant for the user brightness level setting from
OS. However, we update it along with other ABM levels to the real PWM
value which could be ABMed.
[How]
Driver to cache and restore the user brightness level setting so that
DMUB can retrieve the last user setting in ABM config initialization.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Camille Cho <camille.cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Fix minor issues in BW Allocation Phase2.
[How]
- In set_usb4_req_bw_req(), link->dpia_bw_alloc_config.response_ready
flag should be reset before writing DPCD REQUEST_BW.
- Fix the granularity for value of 2 in get_bw_granularity().
- Removed bandwidth allocation support display fw boot option as
the fw would read feature enable status from bios.
- Clean up DPIA_EST_BW_CHANGED and DPIA_BW_REQ_SUCCESS cases in
dpia_handle_bw_alloc_response().
- Removed allocate_usb4_bw and deallocate_usb4_bw.
- Optimized loop in get_lowest_dpia_index().
- Updated link_dp_dpia_allocate_usb4_bandwidth_for_stream() and
set_usb4_req_bw_req() to always issue request bw.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: PeiChen Huang <peichen.huang@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some functions whose output is typically checked for null are not being
checked for null at several call sites, causing some static analysis
tools to throw an error.
[How]
Add null pointer guards around functions that typically have them at
other call sites.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Josip Pavic <josip.pavic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain HDMI modes failed at dml cap check for uncompressed video but
they can still be supported for compressed video.
[How]
Add HDMI capacity computations using fixed31_32 in dc side.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Chris Park <chris.park@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
More information is desired for the test tools.
[How]
Refactored get_subvp_visual_confirm_color and
get_mclk_switch_visual_confirm_color to support the new method of
storing the p_state type, which was changed so that it could also be
saved and output by the DPM log. Ensured that the p_state type is kept
updated by looping through the pipes within commit_planes_for_stream.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Relja Vojvodic <relja.vojvodic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In DCN32/321 FPO uses per-pipe P-State force. If there is no plane, then
then HUBP is power gated, in which case any programming in HUBP has no
effect and the pipe is always asserting P-State allow. This is contrary
to what we want to happen for FPO (FW should moderate the P-State
assertion), so block FPO if there's no plane for the FPO pipe.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Reviewed-by: Samson Tam <samson.tam@amd.com>
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is some logic error where the wrong variable was used to check for
OTG_MASTER and DPP_PIPE.
[How]
Add booleans to confirm that the expected pipes were found before
validating schedulability.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Reviewed-by: Samson Tam <samson.tam@amd.com>
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Idle power optimization was disabled on dcn35 by default.
[How]
Enable by setting disable_idle_power_optimizations to false.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Instability is observed on DCN35 if idle power optimization is enabled.
[How]
Disable IPS until issue is resolved.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Variable remainder is being initialized with a value that is never read,
the assignment is redundant and can be removed. Also add a newline
after the declaration to clean up the coding style.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This DC patchset brings improvements in multiple areas. In summary, we highlight:
- change static screen wait frame_count for ips
- Fix hang/underflow when transitioning to ODM4:1
- Only clear symclk otg flag for HDMI
- Fix lightup regression with DP2 single display configs
- Refactor phantom resource allocation
- Refactor dc_state interface
- Wake DMCUB before executing GPINT commands
- Wake DMCUB before sending a command
- Refactor DMCUB enter/exit idle interface
- enable dcn35 idle power optimization
- fix usb-c connector_type
- add debug option for ExtendedVBlank DLG adjust
- Set test_pattern_changed update flag on pipe enable
- dereference variable before checking for zero
- get dprefclk ss info from integration info table
- skip error logging when DMUB is inactive from S3
- make flip_timestamp_in_us a 64-bit variable
- Add case for dcn35 to support usb4 dmub hpd event
- Add function for dumping clk registers
- Unify optimize_required flags and VRR adjustments
- Revert using channel_width as 2 for vram table 3.0
- remove HPO PG in driver side
- do not send commands to DMUB if DMUB is inactive from S3
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Remove unused dmub_fw_boot_options flag
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
the original wait for 2 static frames before enter static screen
was not good enough for IPS-enabled case since enter/exit takes more time.
[How]
Changed logic for hardcoded wait frame values.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Allen Pan <allen.pan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Under some circumstances, disabling an OPTC and attempting to reclaim
its OPP(s) for a different OPTC could cause a hang/underflow due to OPPs
not being properly disconnected from the disabled OPTC.
[How]
Ensure that all OPPs are unassigned from an OPTC when it gets disabled.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
There is a corner case where the symclk otg flag is cleared
when disabling the phantom pipe for subvp (because the phantom
and main pipe share the same link). This is undesired because
we need the maintain the correct symclk otg flag state for
the main pipe.
For now only clear the flag only for HDMI signal type, since
it's only set for HDMI signal type (phantom is virtual). The
ideal solution is to not clear it if the stream is phantom but
currently there's a bug that doesn't allow us to do this. Once
this issue is fixed the proper fix can be implemented.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Previous fix for multiple displays downstream of DP2 MST hub caused regression
[HOW]
Match sink IDs instead of sink struct addresses
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
dml2_context should be deep copied from src to dst dc_state.
Reviewed-by: George Shen <george.shen@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
After refactoring dc_state, it is always constructed at the time of its
creation. Construction can only happen after dc resources are initialized, so
move creation to be after this.
Reviewed-by: George Shen <george.shen@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
Need to provide valid pointer to dc_state when getting subvp pipe type.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Phantom streams and planes were previously not referenced explcitly on creation.
[HOW?]
To reduce memory management complexity, add an additional phantom streams and planes
reference into dc_state, and move mall_stream_config to stream_status inside
the state to make it safe to modify in shallow copies. Also consildates any logic
that is affected by this change to dc_state.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Part of the dc_state interface that deals with adding streams and planes should
remain public, while others that deal with internal status' and subvp should be
private to DC.
[HOW?]
Move and rename the public functions to dc_state.h and private functions to
dc_state_priv.h. Also add some additional functions for extracting subvp meta
data from the state.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMCUB can be in idle when we attempt to interface with the HW through
the GPINT mailbox resulting in a system hang.
[How]
Add dc_wake_and_execute_gpint() to wrap the wake, execute, sleep
sequence.
If the GPINT executes successfully then DMCUB will be put back into
sleep after the optional response is returned.
It functions similar to the inbox command interface.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can hang in place trying to send commands when the DMCUB isn't
powered on.
[How]
For functions that execute within a DC context or DC lock we can
wrap the direct calls to dm_execute_dmub_cmd/list with code that
exits idle power optimizations and reallows once we're done with
the command submission on success.
For DM direct submissions the DM will need to manage the enter/exit
sequencing manually.
We cannot invoke a DMCUB command directly within the DM execution
helper or we can deadlock.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can hang in place trying to send commands when the DMCUB isn't
powered on.
[How]
We need to exit out of the idle state prior to sending a command,
but the process that performs the exit also invokes a command itself.
Fixing this issue involves the following:
1. Using a software state to track whether or not we need to start
the process to exit idle or notify idle.
It's possible for the hardware to have exited an idle state without
driver knowledge, but entering one is always restricted to a driver
allow - which makes the SW state vs HW state mismatch issue purely one
of optimization, which should seldomly be hit, if at all.
2. Refactor any instances of exit/notify idle to use a single wrapper
that maintains this SW state.
This works simialr to dc_allow_idle_optimizations, but works at the
DMCUB level and makes sure the state is marked prior to any notify/exit
idle so we don't enter an infinite loop.
3. Make sure we exit out of idle prior to sending any commands or
waiting for DMCUB idle.
This patch takes care of 1/2. A future patch will take care of wrapping
DMCUB command submission with calls to this new interface.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
BIOS switches to use USB-C connector type 0x18, but VBIOS's
objectInfo table not supported yet. driver needs to patch it
based on enc_cap from system integration info table.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Allen Pan <allen.pan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Add new option for debug usage
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In certain cases, ODM pipe split can occur while stream already has test
pattern enabled. The new pipe used in the ODM combine config must be
configured to output the test pattern in this case.
[How]
If the stream is configured to output test pattern, then set the
test_pattern_changed update flag for the new pipe when it gets enabled.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver incorrectly checks if pointer variable OutBpp is null instead of
if the value being pointed to is zero.
[How]
Dereference OutBpp before checking for a value of zero.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Josip Pavic <josip.pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
we have two SSC_En:
we get ssc_info from dce_info for MPLL_SSC_EN.
we used to call VBIOS cmdtbl's smu_info's SS persentage for DPRECLK SS info,
is used for DP AUDIO and VBIOS' smu_info table was from systemIntegrationInfoTable.
since dcn35 VBIOS removed smu_info, driver need to use integrationInfotable directly.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On resume from S3, while DMUB is inactive, DMUB queue and execute
calls will not work. Skip reporting errors in these scenarios
[How]
Add new return code during DMUB queue and execute calls when DMUB
is in S3 state. Skip logging errors in these scenarios
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This variable currently overflows after about 71 minutes. This doesn't
cause any known functional issues but it does make debugging more
difficult.
[How]
Make it a 64-bit variable.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Josip Pavic <josip.pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & how]
Refactor dc_is_dmub_outbox_supported() a bit and add case for dcn35 to
register dmub outbox notification irq to handle usb4 relevant hpd event.
Reviewed-by: Roman Li <roman.li@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There have recently been changes that break backwards compatibility,
that were introduced into DMUB firmware (for DCN32x) concerning FPO and
SubVP. So, since those are just power optimization features, we can just
disable them unless the user is using a new enough version of DMUB
firmware.
Cc: stable@vger.kernel.org
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2870
Fixes: ed6e2782e9 ("drm/amd/display: For cursor P-State allow for SubVP")
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Closes: https://lore.kernel.org/r/CABXGCsNRb0QbF2pKLJMDhVOKxyGD6-E+8p-4QO6FOWa6zp22_A@mail.gmail.com/
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some issues have been raised that appear to be tied to PSR-SU.
To allow users to confirm they're tied to PSR-SU without turning off
PSR entirely introduce a new debug mask:
amdgpu.dcdebugmask=0x200
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Allow devs to check raw clk register values by dumping them on the log
[how]
Add clk register dump implementation
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Johnson Chen <johnson.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is only a single call to dc_post_update_surfaces_to_stream so
there is no need to have two flags to control it. Unifying this to a
single flag allows dc_stream_adjust_vmin_vmax to skip actual
programming when there is no change required.
[how]
Remove wm_optimze_required flag and set only optimize_required in its
place. Then in dc_stream_adjust_vmin_vmax, check that the stream timing
range matches the requested one and skip programming if they are equal.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Revert commit fec05adc40 ("drm/amd/display: Use channel_width = 2 for vram table 3.0")
Because the issue is being fixed from VBIOS side.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Add config to make HPO PG handled in dmubfw ips entry/exit
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On resume from S3, may get apply_idle_optimizations call while DMUB
is inactive which will just time out.
[How]
Set and track power state in dmub_srv and check power state before
sending commands to DMUB. Add interface in both dmub_srv and
dc_dmub_srv
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
warning: expecting prototype for drm_crtc_additional_color_mgmt().
Prototype was for dm_crtc_additional_color_mgmt() instead
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312141801.o9eBCxt9-lkp@intel.com/
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It takes the plane state rather than the crtc state.
Fixes: aba8b76baa ("drm/amd/display: add plane shaper LUT support")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Melissa Wen <mwen@igalia.com>
Cc: Harry.Wentland@amd.com
Create drm_color_ctm_3x4 to support 3x4-dimension plane CTM matrix and
convert DRM CTM to DC CSC float matrix.
v3:
- rename ctm2 to ctm_3x4 (Harry)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Map the plane CTM driver-specific property to DC plane, instead of DC
stream. The remaining steps to program DPP block are already implemented
on DC shared-code.
v3:
- fix comment about plane and CRTC CTMs priorities (Harry)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Plane CTM for pre-blending color space conversion. Only enable
driver-specific plane CTM property on drivers that support both pre- and
post-blending gamut remap matrix, i.e., DCN3+ family. Otherwise it
conflits with DRM CRTC CTM property.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When commiting planes, we copy color mgmt resources to the stream state.
Do the same for shaper and 3D LUTs.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Co-developed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pm supports return vpe clock table and soc clock table
Signed-off-by: Peyton Lee <peytolee@amd.com>
Reviewed-by: Li Ma <li.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to funnel the color caps through to these functions so it can check
that the hardware is capable.
v2:
- remove redundant color caps assignment on plane degamma map (Harry)
- pass color caps to degamma params
v3:
- remove unused color_caps parameter from set_color_properties (Harry)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Map plane blend properties to DPP blend gamma. Plane blend is a
post-3D LUT curve that linearizes color space for blending. It may be
defined by a user-blob LUT and/or predefined transfer function. As
hardcoded curve (ROM) is not supported on blend gamma, we use AMD color
module to fill parameters when setting non-linear TF with empty LUT.
v2:
- rename DRM TFs to AMDGPU TFs
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Unlike degamma, blend gamma doesn't support hardcoded curve
(predefined/ROM), but we can use AMD color module to fill blend gamma
parameters when we have non-linear plane gamma TF without plane gamma
LUT. The regular degamma path doesn't hit this.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wire up DC 3D LUT to DM plane color management (pre-blending). On AMD
display HW, 3D LUT comes after a shaper curve and we always have to
program a shaper curve to delinearize or normalize the color space
before applying a 3D LUT (since we have a reduced number of LUT
entries).
In this version, the default values of 3D LUT for size and bit_depth are
17x17x17 and 12-bit, but we already provide here a more generic
mechanisms to program other supported values (9x9x9 size and 10-bit).
v2:
- started with plane 3D LUT instead of CRTC 3D LUT support
v4:
- lut3d_size is the max dimension size instead of # of entries
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable usage of predefined transfer func in addition to shaper 1D LUT.
That means we can save some complexity by just setting a predefined
curve, instead of programming a custom curve when preparing color space
for applying 3D LUT.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Map DC shaper LUT to DM plane color management. Shaper LUT can be used
to delinearize and/or normalize the color space for computational
efficiency and achiving specific visual styles. If a plane degamma is
apply to linearize the color space, a custom shaper 1D LUT can be used
just before applying 3D LUT.
v2:
- use DPP color caps to verify plane 3D LUT support
- add debug message if shaper LUT programming fails
v4:
- remove helper to check 3D LUT color caps (Harry)
- update desc of lut3d-setup helper from MPC to DPP
v5:
- remove color_mgmt_changed check that prevents color updates (Joshua)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With `dc_fixpt_from_s3132()` translation, we can just use it to set
hdr_mult.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Detach value translation from CTM to reuse it for programming HDR
multiplier property.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC only has pre-blending degamma caps (plane/DPP) that is currently in
use for CRTC/post-blending degamma, so that we don't have HW caps to
perform plane and CRTC degamma at the same time. Reject atomic updates
when serspace sets both plane and CRTC degamma properties.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set DC plane with user degamma LUT or predefined TF from driver-specific
plane color properties. If plane and CRTC degamma are set in the same
time, plane degamma has priority. That means, we only set CRTC degamma
if we don't have plane degamma LUT or TF to configure. We return -EINVAL
if we don't have plane degamma settings, so we can continue and check
CRTC degamma.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The next patch adds pre-blending degamma to AMD color mgmt pipeline, but
pre-blending degamma caps (DPP) is currently in use to provide DRM CRTC
atomic degamma or implict degamma on legacy gamma. Detach degamma usage
regarging CRTC color properties to manage plane and CRTC color
correction combinations.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We should reset a plane state if at least one of the color management
properties differs from old and new state.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Co-developed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise this is just initialized to 0. This needs to actually have a
value so that compute_curve can work for PQ EOTF.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Co-developed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Including drm_edid.h from amdgpu_mode.h causes the rebuild of literally
hundreds of files when drm_edid.h is modified, while there are only a
handful of files that actually need to include drm_edid.h.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add predefined transfer function programming. There is no post-blending
out gamma ROM for hardcoded curves, but we can use AMD color modules to
program LUT parameters from pre-defined coefficients and an empty
regamma LUT (or bump up LUT parameters with pre-defined TF values).
v2:
- update crtc color mgmt if regamma TF differs between states (Joshua)
- map inverse EOTF to DC transfer function (Melissa)
v3:
- update AMDGPU TF list
v4:
- update comment regarding regamma behavior
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Co-developed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We will wire up MPC 3D LUT to DM CRTC color pipeline in the next patch,
but so far, only for atomic interface. By checking
set_output_transfer_func in DC drivers with MPC 3D LUT support, we can
verify that regamma is only programmed when 3D LUT programming fails. As
a groundwork to introduce 3D LUT programming and better understand each
step, detach atomic regamma programming from the crtc colocr updating
code.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Describe some expected behavior of the AMD DM color mgmt programming.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add AMD pre-defined transfer function property to default DRM CRTC gamma
to convert to wire encoding with or without a user gamma LUT. There is
no post-blending regamma ROM for pre-defined TF. When setting Gamma TF
(!= Identity) and LUT at the same time, the color module will combine
the pre-defined TF and the custom LUT values into the LUT that's
actually programmed.
v2:
- enable CRTC prop in the end of driver-specific prop sequence
- define inverse EOTFs as supported regamma TFs
- reword driver-specific function doc to remove shaper/3D LUT
v3:
- spell out TF+LUT behavior in the commit and comments (Harry)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Co-developed-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Blend 1D LUT or a pre-defined transfer function (TF) can be set to
linearize content before blending, so that it's positioned just before
blending planes in the AMD color mgmt pipeline, and after 3D LUT
(non-linear space). Shaper and Blend LUTs are 1D LUTs that sandwich 3D
LUT. Drivers should advertize blend properties according to HW caps.
There is no blend ROM for pre-defined TF. When setting blend TF (!=
Identity) and LUT at the same time, the color module will combine the
pre-defined TF and the custom LUT values into the LUT that's actually
programmed.
v3:
- spell out TF+LUT behavior in the commit and comments (Harry)
v5:
- get blend blob correctly
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On AMD HW, 3D LUT always assumes a preceding shaper 1D LUT used for
delinearizing and/or normalizing the color space before applying a 3D
LUT. Add pre-defined transfer function to enable delinearizing content
with or without shaper LUT, where AMD color module calculates the
resulted shaper curve. We apply an inverse EOTF to go from linear
values to encoded values. If we are already in a non-linear space and/or
don't need to normalize values, we can bypass shaper LUT with a linear
transfer function that is also the default TF value.
There is no shaper ROM. When setting shaper TF (!= Identity) and LUT at
the same time, the color module will combine the pre-defined TF and the
custom LUT values into the LUT that's actually programmed.
v2:
- squash commits for shaper LUT and shaper TF
- define inverse EOTF as supported shaper TFs
v3:
- spell out TF+LUT behavior in the commit and comments (Harry)
- replace BT709 EOTF by inv OETF
v5:
- get shaper blob correctly (Joshua)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add 3D LUT property for plane color transformations using a 3D lookup
table. 3D LUT allows for highly accurate and complex color
transformations and is suitable to adjust the balance between color
channels. It's also more complex to manage and require more
computational resources.
Since a 3D LUT has a limited number of entries in each dimension we want
to use them in an optimal fashion. This means using the 3D LUT in a
colorspace that is optimized for human vision, such as sRGB, PQ, or
another non-linear space. Therefore, userpace may need one 1D LUT
(shaper) before it to delinearize content and another 1D LUT after 3D
LUT (blend) to linearize content again for blending. The next patches
add these 1D LUTs to the plane color mgmt pipeline.
v3:
- improve commit message about 3D LUT
- describe the 3D LUT entries and size (Harry)
v4:
- advertise 3D LUT max size as the size of a single-dimension
v5:
- get lut3d blob correctly (Joshua)
- fix doc about 3d-lut dimension size (Sebastian)
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
'wb_info' needs to be freed on error paths or it would leak the memory.
Smatch pointed this out.
Fixes: c81e13b929 ("drm/amd/display: Hande writeback request from userspace")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Multiplier to 'gain' the plane. When PQ is decoded using the fixed func
transfer function to the internal FP16 fb, 1.0 -> 80 nits (on AMD at
least) When sRGB is decoded, 1.0 -> 1.0. Therefore, 1.0 multiplier = 80
nits for SDR content. So if you want, 203 nits for SDR content, pass in
(203.0 / 80.0).
v4:
- comment about the PQ TF need for L-to-NL (from Harry's review)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Co-developed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Brief documentation about pre-defined transfer function usage on AMD
display driver and standardized EOTFs and inverse EOTFs.
v3:
- Document BT709 OETF (Pekka)
- Fix description of sRGB and pure power funcs (Pekka)
v4:
- Add description of linear and non-linear forms (Harry)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Co-developed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of relying on color block names to get the transfer function
intention regarding encoding pixel's luminance, define supported
Electro-Optical Transfer Functions (EOTFs) and inverse EOTFs, that
includes pure gamma or standardized transfer functions.
v3:
- squash linear and unity TFs to identity (Pekka)
- define the right TFs for BT.709 (Pekka and Harry)
- add comment about AMD TF coefficients
Suggested-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allow userspace to tell the kernel driver the input space and,
therefore, uses correct predefined transfer function (TF) to go from
encoded values to linear values.
v2:
- rename TF enum prefix from DRM_ to AMDGPU_ (Harry)
- remove HLG TF
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Co-developed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When screen brightness is rapidly changed and PSR-SU is enabled the
display hangs on panels with this TCON even on the latest DCN 3.1.4
microcode (0x8002a81 at this time).
This was disabled previously as commit 072030b178 ("drm/amd: Disable
PSR-SU on Parade 0803 TCON") but reverted as commit 1e66a17ce5 ("Revert
"drm/amd: Disable PSR-SU on Parade 0803 TCON"") in favor of testing for
a new enough microcode (commit cd2e31a9ab ("drm/amd/display: Set minimum
requirement for using PSR-SU on Phoenix")).
As hangs are still happening specifically with this TCON, disable PSR-SU
again for it until it can be root caused.
Cc: stable@vger.kernel.org
Cc: aaron.ma@canonical.com
Cc: binli@gnome.org
Cc: Marc Rossi <Marc.Rossi@amd.com>
Cc: Hamza Mahfooz <Hamza.Mahfooz@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2046131
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Power up and power down has reverted programming order.
also make sure disable root clock last.
Reviewed-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- When we're in a no plane config, DCN is always asserting
P-State allow
- This creates a scenario where the P-State blackout can start
just as VUPDATE takes place and transitions the DCN config to
a one where one or more HUBP's are active which can result in
underflow
- To fix this issue, force p-state disallow and unforce after
the transition from no planes case -> one or more planes active
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
For mode programming we want to extend the prefetch as much as possible
(up to oto, or as long as we can for equ) if we're not already applying
the 60us prefetch requirement. This is to avoid intermittent underflow
issues during prefetch.
The prefetch extension is applied under the following scenarios:
1. We're in prefetch mode 1 (i.e. we don't support MCLK switch in blank)
2. We're using subvp or drr methods of p-state switch, in which case we
we don't care if prefetch takes up more of the blanking time
Mode programming typically chooses the smallest prefetch time possible
(i.e. highest bandwidth during prefetch) presumably to create margin between
p-states / c-states that happen in vblank and prefetch. Therefore we only
apply this prefetch extension when p-state in vblank is not required (UCLK
p-states take up the most vblank time).
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
User interface cannot guarantee system is in
idle state, so need to ensure we exit idle state
before accessing any HW data.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To match the hardware sequence
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Allen <allen.pan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dtbclk is unavaliable from pmfw. Try to grab the value from bounding box
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
FP guard is valid for all recent asics, not just RV, so fix the comment.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
HostVMMinPageSize is expected to be in KB according to spec,
the checks later down the line reflect this as well.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
With DP2.1a expansion we are allowing DP40 cables to do UHBR13.5
how:
Assume UHBR10 means UHBR13.5 also for unknown cable type and
passive cable type.
Reviewed-by: George Shen <george.shen@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ran Shi <ran.shi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Replace direct usage of adev->ip_versions with amdgpu_ip_version.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hook up driver-specific atomic operations for managing AMD color
properties. Create AMD driver-specific color management properties
and attach them according to HW capabilities defined by `struct
dc_color_caps`.
First add plane degamma LUT properties that means user-blob and its
size. We will add more plane color properties in the next patches. In
addition, we define AMD_PRIVATE_COLOR to guard these driver-specific
plane properties.
Plane degamma can be used to linearize input space for arithmetical
operations that are more accurate when applied in linear color.
v2:
- update degamma LUT prop description
- move private color operations from amdgpu_display to amdgpu_dm_color
v5:
- get degamma blob correctly (Joshua)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Co-developed-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in a smu_print message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmV2PMQeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGhgQIAKSdjtpkv+IeDwph
umLHxDlCTT8nl+TAhEYuxSdMiHt1i7+zyF0snnHhGthBRnBZBf+PDdkQOmqtjLZj
e591VGY7tdNCAVUwmRRaI82JFz9Pl1k8DXL3f+CE1+MfbpsirAecoIAL0rsvg+4f
ICKSAOBZonL7GT7IGrsbxgqGKCLC+2PcgNT4pADBdjtbC1nmVSLK21dtWr6i4xsn
CT9MxAnej1+EOpreyHhNZUVqfQy0/04x4OY0u/EOXU3PgpfGTrAzkyfwzcd/eit0
x59TZ0owDVXfvvdXUUAC0zG1th2ek5LKNtL+C4rKOoAbq7GZoQfjN5M/Ug+yykwE
aqm6CJ8=
=tZ+R
-----END PGP SIGNATURE-----
Backmerge tag 'v6.7-rc5' into drm-next
Linux 6.7-rc5
Alex requested this for some amdkfd work relying on the symbols exports.
Signed-off-by: Dave Airlie <airlied@redhat.com>
UAPI Changes:
- Remove Userspace Mode-Setting ioctls
- v3d: New uapi to handle jobs involving the CPU
Cross-subsystem Changes:
Core Changes:
- atomic: Add support for FB-less planes which got reverted a bit
later for lack of IGT tests and userspace code, Dump private objects
state in drm_state_dump.
- dma-buf: Add fence deadline support
- encoder: Create per-encoder debugfs directory, move the bridge chain
file to that directory
Driver Changes:
- Include drm_auth.h in driver that use it but don't include it, Drop
drm_plane_helper.h from drivers that include it but don't use it
- imagination: Plenty of small fixes
- panfrost: Improve interrupt handling at poweroff
- qaic: Convert to persistent DRM devices
- tidss: Support for the AM62A7, a few probe improvements, some cleanups
- v3d: Support for jobs involving the CPU
- bridge:
- Create transparent aux-bridge for DP/USB-C
- lt8912b: Add suspend/resume support and power regulator support
- panel:
- himax-hx8394: Drop prepare, unprepare and shutdown logic, Support
panel rotation
- New panels: BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G,
Evervision VGG644804, SDC ATNA45AF01
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCZXGXPAAKCRDj7w1vZxhR
xblIAP4tz7X0mqa7KFr6L0sIfVILHANho4L81IUFi+kpTn64WgEAnqJ3IqJtdLbi
czXzgJPae3Ifstm7CW7+72fLQCR6Cg8=
=pU2c
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2023-12-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 6.8:
UAPI Changes:
- Remove Userspace Mode-Setting ioctls
- v3d: New uapi to handle jobs involving the CPU
Cross-subsystem Changes:
Core Changes:
- atomic: Add support for FB-less planes which got reverted a bit
later for lack of IGT tests and userspace code, Dump private objects
state in drm_state_dump.
- dma-buf: Add fence deadline support
- encoder: Create per-encoder debugfs directory, move the bridge chain
file to that directory
Driver Changes:
- Include drm_auth.h in driver that use it but don't include it, Drop
drm_plane_helper.h from drivers that include it but don't use it
- imagination: Plenty of small fixes
- panfrost: Improve interrupt handling at poweroff
- qaic: Convert to persistent DRM devices
- tidss: Support for the AM62A7, a few probe improvements, some cleanups
- v3d: Support for jobs involving the CPU
- bridge:
- Create transparent aux-bridge for DP/USB-C
- lt8912b: Add suspend/resume support and power regulator support
- panel:
- himax-hx8394: Drop prepare, unprepare and shutdown logic, Support
panel rotation
- New panels: BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G,
Evervision VGG644804, SDC ATNA45AF01
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/yu5heqaufyeo4nlowzieu4s5unwqrqyx4jixbfjmzdon677rpk@t53vceua2dao
Mark reports that brightness is not restored after Xorg dpms screen blank.
This behavior was introduced by commit d9e865826c ("drm/amd/display:
Simplify brightness initialization") which dropped the cached backlight
value in display code, but also removed code for when the default value
read back was less than 1 nit.
Restore this code so that the backlight brightness is restored to the
correct default value in this circumstance.
Reported-by: Mark Herbert <mark.herbert42@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3031
Cc: stable@vger.kernel.org
Cc: Camille Cho <camille.cho@amd.com>
Cc: Krunoslav Kovac <krunoslav.kovac@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Fixes: d9e865826c ("drm/amd/display: Simplify brightness initialization")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We currently don't support dirty rectangles on hardware rotated modes.
So, if a user is using hardware rotated modes with PSR-SU enabled,
use PSR-SU FFU for all rotated planes (including cursor planes).
Cc: stable@vger.kernel.org
Fixes: 30ebe41582 ("drm/amd/display: add FB_DAMAGE_CLIPS support")
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2952
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Bin Li <binli@gnome.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Does the same thing as:
commit 6740ec97bc ("drm/amd/display: Increase frame warning limit with KASAN or KCSAN in dml2")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202311302107.hUDXVyWT-lkp@intel.com/
Fixes: 67e38874b8 ("drm/amd/display: Increase num voltage states to 40")
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Alvin Lee <alvin.lee2@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Samson Tam <samson.tam@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
[Why]
UBSAN errors observed in dmesg.
array-index-out-of-bounds in dml2/display_mode_core.c
[How]
Fix the index.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some eDP panels's ext caps don't write initial value cause the value of
dpcd_addr(0x317) is random. It means that sometimes the eDP will
clarify it is OLED, miniLED...etc cause the backlight control interface
is incorrect.
[HOW]
Add a new panel patch to remove sink ext caps(HDR,OLED...etc)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Ivan Lipski <ivlipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VBIOS has suggested to use channel_width=2 for any ASIC that uses vram
info 3.0. This is because channel_width in the vram table no longer
represents the memory width
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Does the same thing as:
commit 6740ec97bc ("drm/amd/display: Increase frame warning limit with KASAN or KCSAN in dml2")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202311302107.hUDXVyWT-lkp@intel.com/
Fixes: 67e38874b8 ("drm/amd/display: Increase num voltage states to 40")
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Alvin Lee <alvin.lee2@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Samson Tam <samson.tam@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
This version brings along following fixes:
* Enable writeback.
* Add multiple fixes for DML2 and DCN35.
* Introduce small code style adjustments.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This simple commit adjusts part of the code style in some of the dc bios
files.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
UBSAN errors observed in dmesg.
array-index-out-of-bounds in dml2/display_mode_core.c
[How]
Fix the index.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
drm_writeback requires to capture exact one frame in each writeback
call.
[HOW]
frame_capture is disabled after each writeback is completed.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Add a function to enable and disable DWB's frame captures.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Hardware may require different warmup approaches - big buffer or
individual buffers.
[HOW]
Setup warmup for big buffer when it is required by specific hardware.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Add a new field to keep track whether a crtc is previously
writeback-enabled.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Counter j was not updated to present the num of writeback_info when
writeback pipes are removed.
[HOW]
update j (num of writeback info) under the correct condition.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
hw_points_num is 0 before ogam LUT is programmed; however, function
"dwb3_program_ogam_pwl" assumes hw_points_num is always greater than 0,
i.e. substracting it by 1 as an array index.
[HOW]
Check hw_points_num is not equal to 0 before using it.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
wb_enabled field is set to false before it is used, and the following
code will never be executed.
[HOW]
Setting wb_enable to false after all removal work is completed.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
The enable and disable writeback calls need to be included in the
coressponding functions in dc_stream.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Handle writeback requests and fill in the required information for DWB
programming and setup.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Writeback connectors don't have a physical sink but DC still
needs a sink to function. Create a fake sink and stream for
writeback connectors
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We need to track the dc_link and it would get confusing if
re-using the amdgpu_dm_connector.
[HOW]
Creating new amdgpu_dm_wb_connector.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
This is to check connector type to avoid
unhandled null pointer for writeback connectors.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Fixes: 60e034f286 ("drm/amd/display: Revert "drm/amd/display: Use drm_connector in create_validate_stream_for_sink"")
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
We need to use this function for both amdgpu_dm_connectors
and drm_writeback_connectors. Modify it to operate on
a drm_connector as a common base.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We will be dealing with two types of connector: amdgpu_dm_connector
and drm_writeback_connector.
[HOW]
We want to find both and then cast to the appriopriate type afterwards.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Writeback connectors are based on a different object:
drm_writeback_connector, and are therefore different from
amdgpu_dm_connector. We need to be careful to ensure code
designed for amdgpu_dm_connector doesn't inadvertently try
to operate on a drm_writeback_connector.
[HOW]
Skip them when connector type is DRM_MODE_CONNECTOR_WRITEBACK.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Create a drm_writeback_connector when connector signal equals
SIGNAL_TYPE_VIRTUAL.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Prepare a virtual connector for writeback.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Previously this only excluded build for a few amdgpu_dm
binaries which makes no sense.
[HOW]
Wrap the entire Makefile in "ifneq ($(CONFIG_DRM_AMD_DC),)"
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Virtual stream encoder should not be a free match for thunderbolt or
usbc, and thus should be avoided.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current implementation will choose to use refclk as dscclk. This is not
recommended by hardware team as refclk is a fixed value which could
cause unnecessary power consumption or it could be not enough for large
DSC timings. So we are adding new interfaces so we could switch to use
dynamically generated DSCCLK by DTO. So DSCCLK is programmable based on
current pixel clock and dispclk.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In previous case, Replay didn't identify the IRQ type, This commit fixes
the issues for the interrupt.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Dennis Chan <dennis.chan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Missing clock gating programming blocks memory power on from boot up.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Chris Park <chris.park@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Yihan Zhu <yihan.zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some eDP panels's ext caps don't write initial value cause the value of
dpcd_addr(0x317) is random. It means that sometimes the eDP will
clarify it is OLED, miniLED...etc cause the backlight control interface
is incorrect.
[HOW]
Add a new panel patch to remove sink ext caps(HDR,OLED...etc)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Ivan Lipski <ivlipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When switching to another HDMI mode, we are unnecesarilly
disabling/enabling FIFO causing both HPO and DIG registers to be set at
the same time when only HPO is supposed to be set.
This can lead to a system hang the next time we change refresh rates as
there are cases when we don't disable OTG/FIFO but FIFO is enabled when
it isn't supposed to be.
[How]
Removing the enable/disable FIFO entirely.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is w/a: we need to keep domain 24 power up in driver side, and let
dmubfw handle it for S0i3. For last display unplugged, if OTG in PG, no
interrupt call back coming.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Chris Park <chris.park@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
HW registers were being read to quickly, causing incorrect values to be
logged after a clock frequency was changed
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Relja Vojvodic <relja.vojvodic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DC debug options currently do not function for dynamically adjusting
our watermarks.
[How]
Hook them up before passing them to DML2.
Also make sure we're using dc->bb_overrides since dc->debug isn't
populated during dc_construct.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
w/a use case:
- dual display, compliance, toggling between the displays
- switching between 120Hz 420 -> 144Hz 444 and vice versa
- switching between 144Hz -> 60Hz TMDS or vice versa
It'd typically involve TMDS in some capacity since that's the only link
signal we leave the OTG running but DIO/PHY off you can hit this in
cases where you have multiple displays as well it syncs with the first
active OTG, so if you had OTG[0] mapped and FIFO off you'd hit it even
if OTG[1] was mapped and had FIFO
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
BIOS FW info version 3.5 is introduced to support new ASICs, but it's
content is currently same as 3.4.
[How]
Include minor version 5 in parsing to enable support.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The is_automated flag logic only applies to USB4 DPIA links during DP LL
compliance test automation. The flag should not be set for non-DPIA
cases.
[How]
Add check for DPIA link endpoint type before setting the flag. Also,
rename is_automated to skip_fallback_on_link_loss for clarity.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VBIOS has suggested to use channel_width=2 for any ASIC that uses vram
info 3.0. This is because channel_width in the vram table no longer
represents the memory width
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changing PBN calculation to be more in line with spec. We don't need to
inflate PBN_NATIVE value by the 1.006 margin, since that is already
taken care of in the get_pbn_per_slot function.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rollback to new context for active display: this was previous tested
sequence. Avoid to do OTG master toggle is no active display at all,
this w/a was for fifo err.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Chris Park <chris.park@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Larger data blocks are expected to be transferred between driver and FW
in the future.
[How]
Embiggen the scratch buffer to a cromulent size.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Josip Pavic <josip.pavic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We use spatial dither by default for all output bpc (6/8/10). While it
makes some sense for FP16, for ARGB2101010 surfaces it makes little
sense as even if we skip color pipeline to preserve bit accuracy,
spatial dither adds random noise so a few percent pixels are 1 bit off.
This commit chages the 10bpc out dither policy to rounding.
Also, in Polaris/Vega times, policy used to be round for 10bpc out; it
looks like it got inadvertently changed for Navi. Difference is only
detectable with capture cards.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
OTG inst and pwrseq inst mapping is not align therefore we cannot use
otg_inst as pwrseq inst to get DCIO register.
[How]
1. Pass the correct pwrseq instance to dmub when set abm pipe.
2. LVTMA control index change from panel_inst to pwrseq_inst.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Phil Hsieh <phil.hsieh@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Lewis Huang <lewis.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some registers needed for root clock gating in dcn35 are not defined in
the dccg header.
[How]
Add the needed registers and temporarily disable some register writes
that are now taking place successfully until the registers can be
properly enabled.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Many DCN generations only have two HPO link encoders and therefore only
support driving a max of two DP2 PHYs. DP2 MST hubs currently can not
pass 3x display validation as each downstream sink is enumerated as
separate DP2 output.
[HOW]
Count MST hubs once by treating only 1st remote sink in topology as an
encoder.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When querying DML for a vlevel after pipes have been split or merged the
ODM policy would revert to a default policy, which could cause the query
to use the incorrect ODM status. In this case ODM 2to1 was validated,
but the last DML query would assume no ODM and return the incorrect
vlevel.
[how]
Added ODM check to apply the correct ODM policy before querying DML.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Relja Vojvodic <relja.vojvodic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix issue when override level bigger than default. Levels 5, 6, and 7
had zero stutter latency, this is because override level being
initialized after stutter latency inits.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Reviewed-by: Allen Pan <allen.pan@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Optimize fast validation cases to only validate the highest voltage
level. This works because during fast validation we only care if the
mode can be supported or not (at any vlevel).
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove unnecessary include statements for <drm/drm_plane_helper.h>.
The file contains helpers for non-atomic code and should not be
required by most drivers. No functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231204090852.1650-3-tzimmermann@suse.de
During hibernate sequence the source context might not have a clk_mgr.
So don't use it to look for DML2 support.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2980
Fixes: 7966f319c6 ("drm/amd/display: Introduce DML2")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A number of DML parameters related to HostVM were either missing or
being set incorrectly, which may cause inaccuracies in calculating
margins and determining BW limitations.
[How]
Correct these values where needed and populate the missing values.
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DTBCLK is enabled on idle and it will burn power.
[How]
There's a few issues here:
- Always enabling DTBCLK on clock manager init
- Setting refclk when DTBCLK is supposed to be disabled
- Not applying the correct calculated version refclk, but instead the
base value which might be zero
On dtbclk_en change we'll message PMFW to enable or disable the clock
accordingly.
The DTBDTO will be then based on refclk, but it will be set to the
default fixed value if there was nothing calculated in DML despite the
clock being considered enabled.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY/HOW]
Increase the pstate latency to improve ac/dc transition
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On recent versions of DMUB firmware, if we want to completely disable
ABM we have to pass ABM_LEVEL_IMMEDIATE_DISABLE as the requested ABM
level to DMUB. Otherwise, LCD eDP displays are unable to reach their
maximum brightness levels. So, to fix this whenever the user requests an
ABM level of 0 pass ABM_LEVEL_IMMEDIATE_DISABLE to DMUB instead. Also,
to keep the user's experience consistent map ABM_LEVEL_IMMEDIATE_DISABLE
to 0 when a user tries to read the requested ABM level.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We have dynamic power control in driver but
should be ignored when power is forced on.
[how]
Bypass any power control when it's forced on.
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are a number of instances where we convert HostVMMinPageSize or
GPUVMMinPageSize from bytes to KB by dividing (rather than multiplying) and
vice versa.
Additionally, in some cases, a parameter is passed through DML in KB but
later checked as if it were in bytes.
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Prevent overwrite of dc->config.use_default_clock_table, as it should be
pre-configured.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The new table doesn't have an implicit mapping between Fclk SOC voltage
and MemClk and it currently builds the table off of number of Fclk
states rather than DcfClock states.
The DML table in use is not correct for functionality or power and
does not align with our existing policies for DCN3x.
[How]
Build the table based on DcfClock with the following assumptions:
1. Raising Soc voltage is the most expensive operation, so assume that
running at max DispClock or DppClock is preferable.
2. Assume that we can run at max Fclk / MemClk at any state, but
restrict the maximum state to the very last entry in the table as the
worst case scenario.
3. Assume that Fclk always has a 2x multiplier on DcfClock unless the
table specifies something lower.
Reviewed-by: Taimur Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Handover from DMUB to driver does not perform link rate toggle.
It might cause link training failure for boot up.
[HOW]
Force toggle rate wa for first link train.
link->vendor_specific_lttpr_link_rate_wa should be zero then.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Zhongwei <zhongwei.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some panels with residency period of 2054 exhibit flickering with
Z8 at the end of the frame.
[How]
As a workaround, increase the limit to block these panels.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Flickering occurs on DRR supported panels when engaged in DRR due to
min_dst_y_next becoming larger than the frame size itself.
[How]
In general, we should be able to enter Z8 when this is engaged but it
might be a net power loss even if the calculation wasn't bugged.
Don't support enabling Z8 during the DRR region.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Remove the brightness cache in DC. It uses a single value to represent
the brightness for both SDR and HDR mode. This leads to flash in HDR
on/off. It also unconditionally programs brightness as in HDR mode. This
may introduce garbage on SDR mode in miniLED panel.
[How]
Simplify the initialization flow by removing the DC cache and taking
what panel has as default. Expand the mechanism for PWM to DPCD Aux to
restore cached brightness value generally.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Camille Cho <camille.cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
If during driver init stage there are greater than 20
intermediary voltage states while constructing the SOC
BB we could hit issues because we will index outside of the
clock_limits array and start overwriting data. Increase the
total number of states to 40 to avoid this issue.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently DCN35 does not spread DPREFCLK
[HOW]
Remove hardcoded table with nonzero caps
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
When choosing which dummy p-state latency to use, we
need to use the DRAM speed from validation. The DRAMSpeed
DML variable can change because we use different input
params to DML when populating watermarks set B.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Wrong function is used to translate LUT values to HW format, leading to
visible artifacting in some cases.
[How]
Use the correct cm3_helper function.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We've updated the table but the values aren't being reflected in DML2
calculation.
[How]
Pass them into the bbox overrides.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can override SR watermarks but not Z8 ones.
[How]
Add new parameters for Z8 matching the SR ones and feed them into the
states.
These also weren't being applied to every state, so make sure that
we loop over and update all SOC states if given an override.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In dcn32 DML pipes are ordered the same as dc pipes but only for used
pipes. For example, if dc pipe 1 and 2 are used, their dml pipe indices
would be 0 and 1 respectively. However
update_pipe_slice_table_with_split_flags doesn't skip indices for free
pipes. This causes us to not reference correct dml pipe output when
building pipe topology.
[how]
Use two variables to iterate dc and dml pipes respectively and only
increment dml pipe index when current dc pipe is not free.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Update to the new values per HW team request. Affects both stutter
and z8.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML2 means that the dcn3x policy for calculating z-state support
no longer runs from validate_bandwidth.
This means we are unconditionally allowing Z8, the hardware default.
[How]
Port the policy over to DCN35, but with a few modifications:
- Don't use min_dst_y_next_start as a check for Z8/Z10 allow
- Add support for overriding the Z10 stutter period per ASIC
- Cleanup the code to make the policy assignment more clear
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When waiting for the ACK for INBOX0 message,
we have to ensure to include the udelay
for proper wait time
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A number of DML parameters related to HostVM were either missing or
being set incorrectly, which may cause inaccuracies in calculating
margins and determining BW limitations.
[How]
Correct these values where needed and populate the missing values.
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
Update DSC DPCD parsing to take granular throughput adjustment into
consideration.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DTBCLK is enabled on idle and it will burn power.
[How]
There's a few issues here:
- Always enabling DTBCLK on clock manager init
- Setting refclk when DTBCLK is supposed to be disabled
- Not applying the correct calculated version refclk, but instead the
base value which might be zero
On dtbclk_en change we'll message PMFW to enable or disable the clock
accordingly.
The DTBDTO will be then based on refclk, but it will be set to the
default fixed value if there was nothing calculated in DML despite the
clock being considered enabled.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add a new dmub command in enum dmub_cmd_cab_type
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY/HOW]
Add a new AUX sequence provided by vendor to improve
interop with specific display configurations.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY/HOW]
Limit the dynamic crb to dual stream configs that include eDP
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
checkpatch complains that:
WARNING: braces {} are not necessary for single statement blocks
+ if (pool->base.irqs != NULL) {
+ dal_irq_service_destroy(&pool->base.irqs);
+ }
Fixed it by removing unnecessary braces to fix the coding style issue.
Signed-off-by: RutingZhang <u202112078@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY/HOW]
Increase the pstate latency to improve ac/dc transition
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On recent versions of DMUB firmware, if we want to completely disable
ABM we have to pass ABM_LEVEL_IMMEDIATE_DISABLE as the requested ABM
level to DMUB. Otherwise, LCD eDP displays are unable to reach their
maximum brightness levels. So, to fix this whenever the user requests an
ABM level of 0 pass ABM_LEVEL_IMMEDIATE_DISABLE to DMUB instead. Also,
to keep the user's experience consistent map ABM_LEVEL_IMMEDIATE_DISABLE
to 0 when a user tries to read the requested ABM level.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add a tracing framework, to measure duration, execution count and
longest duration of main loop/vsync interrupt work
GPINT command is used to start/stop the measurements.
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We have dynamic power control in driver but
should be ignored when power is forced on.
[how]
Bypass any power control when it's forced on.
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are a number of instances where we convert HostVMMinPageSize or
GPUVMMinPageSize from bytes to KB by dividing (rather than multiplying) and
vice versa.
Additionally, in some cases, a parameter is passed through DML in KB but
later checked as if it were in bytes.
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Prevent overwrite of dc->config.use_default_clock_table, as it should be
pre-configured.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The new table doesn't have an implicit mapping between Fclk SOC voltage
and MemClk and it currently builds the table off of number of Fclk
states rather than DcfClock states.
The DML table in use is not correct for functionality or power and
does not align with our existing policies for DCN3x.
[How]
Build the table based on DcfClock with the following assumptions:
1. Raising Soc voltage is the most expensive operation, so assume that
running at max DispClock or DppClock is preferable.
2. Assume that we can run at max Fclk / MemClk at any state, but
restrict the maximum state to the very last entry in the table as the
worst case scenario.
3. Assume that Fclk always has a 2x multiplier on DcfClock unless the
table specifies something lower.
Reviewed-by: Taimur Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Move all optc files to unique
folder optc.
[how]
creating optc repo in dc, and moved the dcnxx_optc.c and .h files into
corresponding new folders inside the optc and cleared the linkage
errors by adding relative paths in the Makefile.template.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Parandhaman K <parandhaman.k@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Handover from DMUB to driver does not perform link rate toggle.
It might cause link training failure for boot up.
[HOW]
Force toggle rate wa for first link train.
link->vendor_specific_lttpr_link_rate_wa should be zero then.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Zhongwei <zhongwei.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- To reduce vlevel further, we can try to apply subvp on
configs that already support p-state since the natural
p-state support may not allow for DPM0.
- Add code to try subvp to reduce UCLK DPM level further
if already supported, but don't use subvp if it does not
optimize the DPM level even lower
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit fcfc6ceec3.
[why]
Flickering observed. Regression search pointed to this being
the offending commit.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Yihan Zhu <yihan.zhu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some panels with residency period of 2054 exhibit flickering with
Z8 at the end of the frame.
[How]
As a workaround, increase the limit to block these panels.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Flickering occurs on DRR supported panels when engaged in DRR due to
min_dst_y_next becoming larger than the frame size itself.
[How]
In general, we should be able to enter Z8 when this is engaged but it
might be a net power loss even if the calculation wasn't bugged.
Don't support enabling Z8 during the DRR region.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When otg workaround is applied during clock update, otgs of
tiled display went out of sync.
[How]
To call dc_trigger_sync() after clock update to sync otgs again.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Previously SubVP would never be selected on 1080p60 displays because
it has too much vactive margin. However, implement a change to allow
it like how 1440p60 is allowed.
- Add a new struct such that we have a list of allowed modes for
enabling subvp with vactive margin (currently 1080p60 and 1440p60)
- Also ensure to block drr + vblank cases to prevent unexpected
enablement of new display configs
- Update SW cursor fallback for these new potential cases as well
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If Panel max link off frame count is low, it will cause low residency
for Replay, then Disabled timing sync check in Full screen Video Case.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Dennis Chan <dennis.chan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MST relevant variables are maintained at drm side. As the result, we
still have to call drm_dp_remove_payload_part2() to update the relevant
values regardless the link is under mst mode or not. We used to have a
workaround patch to tackle this: commit 3d8fcc6740 ("drm/amd/display:
Extract temp drm mst deallocation wa into its own function")
Now it's time to remove the workaround and adjust the flow.
[How]
During deallocate_mst_payload(), source actually doesn't send out
ALLOCATE_PAYLOAD at the end as like the flow in allocate_mst_payload().
Call function dm_helpers_dp_mst_send_payload_allocation() at the end of
deallocate_mst_payload() is a bit confusing.
Separate dm_helpers_dp_mst_send_payload_allocation() into 2 functions.
Have a new function dm_helpers_dp_mst_update_mst_mgr_for_deallocation()
to replace dm_helpers_dp_mst_send_payload_allocation() for payload
deallocation.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Remove the brightness cache in DC. It uses a single value to represent
the brightness for both SDR and HDR mode. This leads to flash in HDR
on/off. It also unconditionally programs brightness as in HDR mode. This
may introduce garbage on SDR mode in miniLED panel.
[How]
Simplify the initialization flow by removing the DC cache and taking
what panel has as default. Expand the mechanism for PWM to DPCD Aux to
restore cached brightness value generally.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Camille Cho <camille.cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Sending certain Frameupdate number for Replay Power Evaluation
Reviewed-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
If during driver init stage there are greater than 20
intermediary voltage states while constructing the SOC
BB we could hit issues because we will index outside of the
clock_limits array and start overwriting data. Increase the
total number of states to 40 to avoid this issue.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently DCN35 does not spread DPREFCLK
[HOW]
Remove hardcoded table with nonzero caps
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Augment the function to allow send different format data in different
use case.
Reviewed-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
To refactor DSC and make DSC files unit testable.
[how]
moved the dcnxx_dsc.c and .h files
into corresponding dcn folders inside
the dsc and cleared the linkage errors.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Bhuvana Chandra Pinninti <bhuvanachandra.pinninti@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
When choosing which dummy p-state latency to use, we
need to use the DRAM speed from validation. The DRAMSpeed
DML variable can change because we use different input
params to DML when populating watermarks set B.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Wrong function is used to translate LUT values to HW format, leading to
visible artifacting in some cases.
[How]
Use the correct cm3_helper function.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We've updated the table but the values aren't being reflected in DML2
calculation.
[How]
Pass them into the bbox overrides.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can override SR watermarks but not Z8 ones.
[How]
Add new parameters for Z8 matching the SR ones and feed them into the
states.
These also weren't being applied to every state, so make sure that
we loop over and update all SOC states if given an override.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In the new pipe resource management logic, the special handling for
stereo timings is missing.
This commit implements the same stereo timings handling as old
pipe resource management code.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When ODM slice count is changed, otg master pipe's pixel clock params is
no longer valid as the value is dependent on ODM slice count.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In dcn32 DML pipes are ordered the same as dc pipes but only for used
pipes. For example, if dc pipe 1 and 2 are used, their dml pipe indices
would be 0 and 1 respectively. However
update_pipe_slice_table_with_split_flags doesn't skip indices for free
pipes. This causes us to not reference correct dml pipe output when
building pipe topology.
[how]
Use two variables to iterate dc and dml pipes respectively and only
increment dml pipe index when current dc pipe is not free.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the link requests to skip implicit eDP power control, we should honor
that request.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Update to the new values per HW team request. Affects both stutter
and z8.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML2 means that the dcn3x policy for calculating z-state support
no longer runs from validate_bandwidth.
This means we are unconditionally allowing Z8, the hardware default.
[How]
Port the policy over to DCN35, but with a few modifications:
- Don't use min_dst_y_next_start as a check for Z8/Z10 allow
- Add support for overriding the Z10 stutter period per ASIC
- Cleanup the code to make the policy assignment more clear
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When waiting for the ACK for INBOX0 message,
we have to ensure to include the udelay
for proper wait time
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
To support dynamic switching for Replay timing sync mechanism.
Reviewed-by: ChunTao Tso <chuntao.tso@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Dennis Chan <dennis.chan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Declaration of 'struct drm_device *dev' is redundant, as
'connector->dev' & 'dev_get_drvdata(kdev)' can be directly passed to
'drm_to_adev', without any intermediate DRM device 'dev' variable
Cc: Roman Li <roman.li@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On UHBR links the PBN divider is a fractional number, accordingly store
it in fixed point format. For now drm_dp_get_vc_payload_bw() always
returns a whole number and all callers will use only the integer part of
it which should preserve the current behavior. The next patch will fix
drm_dp_get_vc_payload_bw() for UHBR rates returning a fractional number
for those (also accounting for the channel coding efficiency correctly).
Cc: Lyude Paul <lyude@redhat.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Wayne Lin <wayne.lin@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[Rebased changes in dm_helpers_construct_old_payload() on drm-intel-next]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116131841.1588781-2-imre.deak@intel.com
UAPI Changes:
- drm: Introduce CLOSE_FB ioctl
- drm/dp-mst: Documentation for the PATH property
- fdinfo: Do not align to a MB if the size is larger than 1MiB
- virtio-gpu: add explicit virtgpu context debug name
Cross-subsystem Changes:
- dma-buf: Add dma_fence_timestamp helper
Core Changes:
- client: Do not acquire module reference
- edid: split out drm_eld, add SAD helpers
- format-helper: Cache format conversion buffers
- sched: Move from a kthread to a workqueue, rename some internal
functions to make it clearer, implement dynamic job-flow control
- gpuvm: Provide more features to handle GEM objects
- tests: Remove slow kunit tests
Driver Changes:
- ivpu: Update FW API, new debugfs file, a new NOP job submission test
mode, improve suspend/resume, PM improvements, MMU PT optimizations,
firmware profiling frequency support, support for uncached buffers,
switch to gem shmem helpers, replace kthread with threaded
interrupts
- panfrost: PM improvements
- qaic: Allow to run with a single MSI, support host/device time
synchronization, misc improvements
- simplefb: Support memory-regions, support power-domains
- ssd130x: Unitialized variable fixes
- omapdrm: dma-fence lockdep annotation fix
- tidss: dma-fence lockdep annotation fix
- v3d: Support BCM2712 (RaspberryPi5), Support fdinfo and gputop
- panel:
- edp: Support AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49
V8.0, plus a whole bunch of panels used on Mediatek chromebooks.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCZVc02QAKCRDj7w1vZxhR
xRXbAPsHQkuUz2n1XWx/8uExPCn+PmS5Lg6IcbtvqpfuFrGt1QEA+DaZf2yfekFj
FgY66UExyddH/2LDHzpKa0WJk6l6vQw=
=1HSK
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2023-11-17' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 6.8:
UAPI Changes:
- drm: Introduce CLOSE_FB ioctl
- drm/dp-mst: Documentation for the PATH property
- fdinfo: Do not align to a MB if the size is larger than 1MiB
- virtio-gpu: add explicit virtgpu context debug name
Cross-subsystem Changes:
- dma-buf: Add dma_fence_timestamp helper
Core Changes:
- client: Do not acquire module reference
- edid: split out drm_eld, add SAD helpers
- format-helper: Cache format conversion buffers
- sched: Move from a kthread to a workqueue, rename some internal
functions to make it clearer, implement dynamic job-flow control
- gpuvm: Provide more features to handle GEM objects
- tests: Remove slow kunit tests
Driver Changes:
- ivpu: Update FW API, new debugfs file, a new NOP job submission test
mode, improve suspend/resume, PM improvements, MMU PT optimizations,
firmware profiling frequency support, support for uncached buffers,
switch to gem shmem helpers, replace kthread with threaded
interrupts
- panfrost: PM improvements
- qaic: Allow to run with a single MSI, support host/device time
synchronization, misc improvements
- simplefb: Support memory-regions, support power-domains
- ssd130x: Unitialized variable fixes
- omapdrm: dma-fence lockdep annotation fix
- tidss: dma-fence lockdep annotation fix
- v3d: Support BCM2712 (RaspberryPi5), Support fdinfo and gputop
- panel:
- edp: Support AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49
V8.0, plus a whole bunch of panels used on Mediatek chromebooks.
Note that the one missing s-o-b for 0da611a870 ("dma-buf: add
dma_fence_timestamp helper") has been supplied here, and rebasing the
entire tree with upsetting committers didn't seem worth the trouble:
https://lore.kernel.org/dri-devel/ce94020e-a7d4-4799-b87d-fbea7b14a268@gmail.com/
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/y4awn5vcfy2lr2hpauo7rc4nfpnc6kksr7btmnwaz7zk63pwoi@gwwef5iqpzva
- Add missing chips for HDCP
- Add new command to disable replay timing resync
- Fix encoder disable logic
- Enable DSC Flag in MST Mode Validation
- Change the DMCUB mailbox memory location from FB to inbox
- Add disable timeout option
- Negate IPS allow and commit bits
- Enable DCN clock gating for DCN35
- Prefer currently used OTG master when acquiring free pipe
- Try to acquire a free OTG master not used in cur ctx first
- Clear dpcd_sink_ext_caps if not set
- Enable fast plane updates on DCN3.2 and above
- Add null checks for 8K60 lightup
- Refactor resource into component directory
- Fix DSC not Enabled on Direct MST Sink
- Guard against invalid RPTR/WPTR being set
- Enable CM low mem power optimization
- Fix a debugfs null pointer error
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Add missing HDCP ID in the message id enum.
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Add new command to disable replay timing resync
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
When dsc is possible, MST mode validation includes:
1. if maximum dsc compression cannot fit into end to end bw, mode pruned
2. if native bw cannot fit into end to end bw, try to enabled dsc to see
whether a feasible dsc config can be found
3. if native bw can fit into end to end bw, mode supported
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
PB9 bit 5 was added to signal PQ EOTF in AMD vendor specific infoframe.
This change sets it when appropriate.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Driver continues running whenever there is
is timeout from smu or dmcub.
It is difficult to track failure state
when dcn, dc or dmcub changes on root failure.
[HOW]
Add disable_timeout option to halt driver
whenever there is a failure in response.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Enable DCN clock gating for DCN35.
Disable DTBCLK gate before link training
and re-enable afterwards
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
When acquiring an OTG master pipe we should prefer currently enabled OTG
master pipes first. If there are no free pipes used as current OTG
master pipe then we will try to acquire a currently unused free pipe as
new OTG master instead of tearing down current secondary pipes from ODM
or MPC combine.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
The current otg master pipe allocation logic is not optimized based
current resource context. We should try to acquire a free OTG master not
used in cur cts first to avoid unnecessary pipe switch from current
state.
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Move all resource files to unique folder resource.
[HOW]
Created resource folder in dc, moved the
dcnxx_resource.c and dcnxx_resource.h files into
corresponding new folders inside the resource and
made appropriate changes for compilation in Makefiles.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mounika Adhuri <moadhuri@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For features that are implemented primarily in DMUB (e.g. PSR), it is
useful to be able to trace them at a DMUB level from the kernel,
especially when debugging issues. So, introduce a debugfs interface that
is able to read and set the DMUB trace mask dynamically at runtime and
document how to use it.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
MPC MCM low mem power optimization still causes color distortion on
first SCE enablement, only forces light sleep for it.
DPP low memory power optimization still needs this bit to save power.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Yihan Zhu <yihan.zhu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DENTIST hangs when OTG is off and encoder is on. We were not
disabling the encoder properly when switching from extended mode to
external monitor only.
[HOW]
Disable the encoder using an existing enable/disable fifo helper instead
of enc35_stream_encoder_enable.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Flush command sent to DMCUB spends more time for execution on
a dGPU than on an APU. This causes cursor lag when using high
refresh rate mouses.
[HOW]
1. Change the DMCUB mailbox memory location from FB to inbox.
2. Only change windows memory to inbox.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Lewis Huang <lewis.huang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On s0i3, IPS mask isn't saved and restored.
It is reset to zero on exit.
If it is cleared unexpectedly, driver will
proceed operations while DCN is in IPS2 and
cause a hang.
[HOW]
Negate the bit logic. Default value of
zero indicates it is still in IPS2. Driver
must poll for the bit to assert.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some eDP panels' ext caps don't set initial values
and the value of dpcd_addr (0x317) is random.
It means that sometimes the eDP can be OLED, miniLED and etc,
and cause incorrect backlight control interface.
[HOW]
Add remove_sink_ext_caps to remove sink ext caps (HDR, OLED and etc)
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When cursor moves across screen boarder, lag cursor observed,
since subvp settings need to sync up with vblank that causes
cursor updates being delayed.
[HOW]
Enable fast plane updates on DCN3.2 to fix it.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Tianci Yin <tianci.yin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The following patch will fix a minor issue where a debug message is
referencing an struct that has just being checked whether is null or
not. This has been noticed by using coccinelle, in the following output:
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_helpers.c:540:25-29: ERROR: aconnector is NULL but dereferenced.
Fixes: 5d72e247e5 ("drm/amd/display: switch DC over to the new DRM logging macros")
Signed-off-by: José Pekkarinen <jose.pekkarinen@foxhound.fi>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When ddc_service_construct() is called, it explicitly checks both the
link type and whether there is something on the link which will
dictate whether the pin is marked as hw_supported.
If the pin isn't set or the link is not set (such as from
unloading/reloading amdgpu in an IGT test) then fail the
amdgpu_dm_i2c_xfer() call.
Cc: stable@vger.kernel.org
Fixes: 22676bc500 ("drm/amd/display: Fix dmub soft hang for PSR 1")
Link: https://github.com/fwupd/fwupd/issues/6327
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Add some null checks to fix an issue where 8k60
tiled display fails to light up.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
For the scenario when a dsc capable MST sink device is directly
connected, it needs to use max dsc compression as the link bw constraint.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Roman Li <roman.li@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HW can return invalid values on register read, guard against these being
set and causing us to access memory out of range and page fault.
[HOW]
Guard at sync_inbox1 and guard at pushing commands.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Spotted by coccicheck, there is a redundant check for
v->SourcePixelFormat[k] != dm_444_16. This patch will
remove it. The corresponding output follows.
drivers/gpu/drm/amd/display/dc/dml/dcn30/display_mode_vba_30.c:5130:86-122: duplicated argument to && or ||
Signed-off-by: José Pekkarinen <jose.pekkarinen@foxhound.fi>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The current code does '(bpp << 4) / 16' in the MST PBN
calculation, but that is just the same as 'bpp' so the
DSC codepath achieves absolutely nothing. Fix it up so that
the fractional part of the bpp value is actually used instead
of truncated away. 64*1006 has enough zero lsbs that we can
just shift that down in the dividend and thus still manage
to stick to a 32bit divisor.
And while touching this, let's just make the whole thing more
straightforward by making the passed in bpp value .4 binary
fixed point always, instead of having to pass in different
things based on whether DSC is enabled or not.
v2:
- Fix DSC kunit test cases.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: David Francis <David.Francis@amd.com>
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Fixes: dc48529fb1 ("drm/dp_mst: Add PBN calculation for DSC modes")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Imre: Fix kunit test cases]
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-3-imre.deak@intel.com
The member variable enable_hpo_pg_support is already initialized
and hence the reinitialization instruction can be removed. Issue
identified using the doubleinit.cocci Coccinelle semantic patch script.
Signed-off-by: Bragatheswaran Manickavel <bragathemanick0908@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A recent refactor of DC's DP test pattern automation code requires the
DC stream's test pattern and test pattern color space fields to be
correctly populated before calling dc_link_dp_set_test_pattern.
[How]
Populate stream's test pattern type and color space fields before
calling into DC to program DP test pattern.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DML2 does not handle the case when we have
a single stream sourcing 2 or more planes
that are duplicates of one another. To properly
handle this scenario, pipe index to plane index
mapping is used to decide which plane is being
processed and programmed.
[how]
Create static array of pipe index to plane index map.
Populate the array properly and use in appropriate places.
Reviewed-by: Xi (Alex) Liu <xi.liu@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Similar to FPO, SubVP should also force cursor P-State
allow instead of relying on natural assertion
- Implement code path to force and unforce cursor P-State
allow for SubVP
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Enable the last of the RCO options for dcn35
[How]
Breakout RCO from dccg35_set_physymclk so that
physymclk RCO can be set in dccg_init without
disabling physymclk
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clean-up the code to remove references of all unused
dml architecture versions since only dml2 is actively
used.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is a case when we are switching from ODM combine to Subvp where
minimal transition based off subvp state is required. In thise case, we
need to save and restore mall state when applying minimal transition.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For all the components that participate in DCN architecture, there is a
header in the dc/inch/hw. For some reason, OPTC broke this pattern and
added all the primary functions/structs associated with that in the
dcn10_optc.h file. For consistency's sake, this commit introduces a new
optc.h file and extracts the code from dcn10_optc to this new file.
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Doing a mode timing change causes a hang when OTG is not disabled.
[how]
Add link_enc null check in disable_otg_wa to cover this case.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current Desync IRQ handler will have some potential do not hit the
desync error case. We change to check both desync error HPD and DPCD.
Signed-off-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Robin Chen <robin.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Increase number of bits for IPS boot option
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
Update test link rate DPCD bit field to match spec
Enable RCO options for dcn35
Add missing dml2 init value for dcn35
Enable DCN clock gating
DCN35 Disable cm power optimization
Allow 16 max_slices for DP2 DSC
Fix OTG disable workaround logic
Enable more IPS options
Fix FRL assertion on boot
Fix missing blendTF programming
Update DP HPO MSA with colorimetry from test request
Fix handling duplicate planes on one stream
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For lighting up, some dml2 params needs to be initialized.
One of them escaped initial patch under:
"drm/amd/display: Add DCN35 DML2 support"
[How]
Add missing initialization.
Fixes: 115009d11c ("drm/amd/display: Add DCN35 DML2 support")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DENTIST was hanging when performing DISPCLK update with OTG enabled, as
OTG disable workaround was not executing.
[How]
Workaround was checking against current_state before running, but when
called from optimize_bandwidth (safe_to_lower), we should be checking
against context instead.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For Replay, if we receive HPD, it doesn’t need to reboot the display.
We don’t need to return anything exactly.
[How]
Return nothing just because we don’t need to reboot the display.
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It's useful to disable the recovery mechanism when debugging replay
desync errors.
Signed-off-by: Dennis Chan <Dennis.Chan@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Robin Chen <robin.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Enabling SCE after boot up will cause color distortion.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Yihan Zhu <yihan.zhu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some DP link layer tests request a different colorimetry than the
default one that is used. Currently, our test automation logic does not
update the MSA with the test request value for DP HPO case.
[How]
Update HPO MSA colorimetry with test automation request value.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
An SCR was made to the DP2.0 spec that updated the bit field definition
for UHBR13.5 in the test link rate DPCD register.
[How]
Add new translation to match the SCR update. Keep old translation for
backwards compatibility.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
To help isolate static screen and
video playback tests, we want to enable
an IPS option to allow IPS only on D3 cycle.
[how]
Add DISABLE_DYNAMIC and DISABLE_ALL
IPS disable flags for user control.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Enable root clock optimization options for dcn35
for power savings
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Make sure to ungate the clocks on boot
so programming sequence is done successfully.
[how]
Move the ungate logic after bios init.
Reviewed-by: Xi (Alex) Liu <xi.liu@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When MPO surface pixel format is not ARGB8888, fast update can miss
programming blendTF.
[How]
Set the gamma_change update flag on blend_tf change.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
On boot disable domain22 force power on
decouple dmcub execution to reduce lock granularity
Enable fast update on blendTF change
Fix blend LUT programming
Program plane color setting correctly
amend HPD handler for Replay
Avoid NULL dereference of timing generator
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On some systems dmub commands run at high IRQ, so long running
commands will block other interrupts.
[How]
Decouple wait_for_idle from dmcub queue/execute/wait.
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: JinZe.Xu <jinze.xu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Minor formatting changes
- Update defines to match the bit width of the field it is used for
- Add new boot up bits to control HW sub block regions power
down
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDCP2 enablement fails when domain22 is set to force
power on
[How]
Disable force power on for domain22 on startup
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
LUT write index does not get reset to zero when writing the LUT values
for each separate RGB component, which results in wrong data for 2 of
the 3 components.
[How]
Reset LUT write index to zero before writing each component's data.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There are some registers for plane
color that are skipped programming
on resume. Need to add those as part
of the sequence.
[how]
Add new function hook for programming
plane color control.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When building ARCH=x86_64 allmodconfig with clang, which will typically
have sanitizers enabled, there is a warning about a large stack frame.
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/display_mode_core.c:6265:13: error: stack frame size (2520) exceeds limit (2048) in 'dml_prefetch_check' [-Werror,-Wframe-larger-than]
6265 | static void dml_prefetch_check(struct display_mode_lib_st *mode_lib)
| ^
1 error generated.
Notably, GCC 13.2.0 does not do too much of a better job, as it is right
at the current limit of 2048 (and others have reported being over with
older GCC versions):
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/display_mode_core.c: In function 'dml_prefetch_check':
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/display_mode_core.c:6705:1: error: the frame size of 2048 bytes is larger than 1800 bytes [-Werror=frame-larger-than=]
6705 | }
| ^
In the past, these warnings have been avoided by reducing the number of
parameters to various functions so that not as many arguments need to be
passed on the stack. However, these patches take a good amount of effort
to write despite being mechanical due to code structure and complexity
and they are never carried forward to new generations of the code so
that effort has to be expended every new hardware generation, which
becomes harder to justify as time goes on.
To avoid having a noticeable or lengthy breakage in all{mod,yes}config,
which are easy testing targets that have -Werror enabled, increase the
limit for configurations that have KASAN or KCSAN enabled by 50% so that
cases of extremely poor code generation can still be caught while not
breaking the majority of builds. CONFIG_KMSAN also causes high stack
usage but the frame limit is already set to zero when it is enabled,
which is accounted for by the check for CONFIG_FRAME_WARN=0 in the dml2
Makefile.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Check whether assigned timing generator is NULL or not before
accessing its funcs to prevent NULL dereference.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
An assignment statement was reversed during a refactor which effectively
disabled S/G display outright. Since, we use
adev->mode_info.gpu_vm_support to indicate to the rest of the driver
that S/G display should be enabled and currently it is always set to
false. So, to fix this set adev->mode_info.gpu_vm_support's value to
that of init_data.flags.gpu_vm_support (and not vice versa).
Fixes: 098c13079c ("drm/amd/display: enable S/G display for for recent APUs by default")
Reported-by: Mark Broadworth <mark.broadworth@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC v3.2.256
Summary:
* Fixes null-deref regression after
"drm/amd/display: Update OPP counter from new interface"
* Fixes display flashing when VSR and HDR enabled on dcn32
* Fixes dcn3x intermittent hangs due to FPO
* Fixes MST Multi-Stream light up on dcn35
* Fixes green screen on DCN31x when DVI and HDMI monitors attached
* Adds DML2 improvements
* Adds idle power optimization improvements
* Accommodates panels with lower nit backlight
* Updates SDP VSC colorimetry from DP test automation request
* Reverts "drm/amd/display: allow edp updates for virtual signal"
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
To enable automated testing through IGT, expose an API that is
accessible through debugfs to query current status of SubVP feature.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[HOW&WHY]
Reading the value from
DP_EDP_BACKLIGHT_MODE_SET_REGISTER, DPCD 0x721
before setting the
BP_EDP_PANEL_LUMINANC_CONTROL_ENABLE bit
to ensure there are no accidental overwrites.
Reviewed-by: Sreeja Golui <sreeja.golui@amd.com>
Reviewed-by: Harry Vanzylldejong <harry.vanzylldejong@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Iswara Nagulendran <iswara.nagulendran@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently causes some DP link layer failures, backing out until
the failures are root caused.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
LUT params are not cleared after setting blend TF, which can lead to
same params being used for the shaper, if the shaper func is bypassed.
[How]
Set lut_params to NULL after program_1dlut.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In cases where number of pipes available is less
than num_opp, there will opp instances that are
null
[How]
Add null check to skip over these opp instances
Fixes: 40de8403b9 ("drm/amd/display: Update OPP counter from new interface")
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Provide DCN32 specific sequence and update DCN30 sequence
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Helper function calculates num_ways using 32-bit. But is
returned as 8-bit. If num_ways exceeds 8-bit, then it
reports back the incorrect num_ways and erroneously
uses MALL when it should not
[How]
Make returned value 32-bit and convert after it checks
against caps.cache_num_ways, which is under 8-bit
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit adds the amdgpu_dm_plane_ prefix for all functions in the
amdgpu_dm_plane.c. This change enables an easy way to filter code paths
via ftrace.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The ftrace debug feature allows filtering functions based on a prefix,
which can be helpful in some complex debug scenarios. The driver can
benefit more from this feature if the function name follows some
patterns; for this reason, this commit adds the prefix amdgpu_dm_crtc_
to all the functions that do not have it in the amdgpu_dm_crtc.c file.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit just replaces dc_interrupt_po*r*larity with its correct
name, which is dc_interrupt_polarity.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Virtual sink is not audio-capable and this causes kms_hdmi_inject's
inject-audio to fail. Set it to HDMI according to EDID.
Reviewed-by: Chao-kai Wang <stylon.wang@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 4ad3ee5ccc.
[WHY & HOW]
Virtual signal is not supported as audio capable by DC.
Reviewed-by: Chao-kai Wang <stylon.wang@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Bandwidth validation failure on framepack tests.
Need to double pixel clock when 3D format is
framepack. Also for HDMI displays, we need to
keep the ITC flag to 1 by default.
[how]
Double the pixel clock when using framepack 3D format.
Set hdmi ITC bit to 1.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Intermittent reboot hangs are observed introduced by
"Improve x86 and dmub ips handshake".
[How]
Bring back the commit but fix the polling.
Avoid hanging in place forever by bounding the delay and ensure that
we still message DMCUB on IPS2 exit to notify driver idle has been
cleared.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Unify pipe resource management logic in dc resource layer.
V2:
Add default case for switch.
CC: Hamza Mahfooz <hamza.mahfooz@amd.com>
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need DML2 to support new pipe resource management APIs.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Currently set_default_brightness_aux function uses 5 nits as lower limit
to check for valid default_backlight setting. However some newer panels
can support even lower default settings
Reviewed-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Swapnil Patel <swapnil.patel@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain test equipment vendors check the SDP VSC for colorimetry against
the value from the test request during certain DP link layer tests for
YCbCr test cases.
[How]
Update SDP VSC with colorimetry from test automation request.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need a helper function to check idle power is allowed
so that dc doesn't access any registers that are power-gated.
[how]
Implement helper function to check idle power optimization.
Enable a hook to check if detection is allowed.
V2:
Add function hooks for set and get idle states.
Check if function hook was properly initialized.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Choi <nicholas.choi@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 1288d70208.
Causes intermittent hangs during reboot stress testing.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dcn35 misses .enable_symclk_se hook that makes MST DSC
not functional when having multiple FE clk to be enabled.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Fix incomplete copyright notice in DC code.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When DML 2 was introduced, it changed part of the generic sequence of
DC, which caused issues on previous DCNs with DMUB support. This commit
ensures the new sequence only works for new DCNs from 3.5 and above.
Changes since V1:
- Harry: Use the attribute using_dml2 instead of check the DCN version.
Cc: Vitaly Prosyak <vprosyak@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Cc: Daniel Wheeler <daniel.wheeler@amd.com>
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Fixes: 7966f319c6 ("drm/amd/display: Introduce DML2")
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some ASICs keep backlight powered on after dpms off
command has been issued.
[How]
The check for no edp power sequencing was never going to pass.
The value is never changed from what it is set by design.
Cc: stable@vger.kernel.org # 6.1+
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2765
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When DML2 was introduced, it targeted only new DCN versions. For
controlling which ASIC should use this new version of DML, it was
introduced the using_dml2 attribute. To avoid ambiguities, this commit
explicitly sets using_dml2 to false in all ASICs that do not support
DML2.
Cc: Vitaly Prosyak <vprosyak@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Cc: Daniel Wheeler <daniel.wheeler@amd.com>
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During system boot in second screen only mode on a seamless boot system,
there is a chance that the pipe's det size might not be reset.
[How]
Reset the det size while resetting the pipe during seamless boot.
Reviewed-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmU1ngkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGrsIH/0k/+gdBBYFFdEym
foRhKir9WV3ZX4oIozJjA1f7T+qVYclKs6kaYm3gNepRBb6AoG8pdgv4MMAqhYsf
QMe2XHi0MrO/qKBgfNfivxEa9jq+0QK5uvTbqCRqCAB8LfwVyDqapCmg3EuiZcPW
UbMITmnwLIfXgPxvp9rabmCsTqO6FLbf0GDOVIkNSAIDBXMpcO1iffjrWUbhRa7n
oIoiJmWJLcXLxPWDsRKbpJwzw2cIG08YhfQYAiQnC3YaeRm1FKLDIICRBsmfYzja
rWv9r4dn4TDfV4/AnjggQnsZvz2yPCxNaFSQIT88nIeiLvyuUTJ9j8aidsSfMZQf
xZAbzbA=
=NoQv
-----END PGP SIGNATURE-----
BackMerge tag 'v6.6-rc7' into drm-next
This is needed to add the msm pr which is based on a higher base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit is the last part of the fix that reduces the stack size in
the DML2 code.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Chaitanya Dhere <chaitanya.dhere@amd.com>
Fixes: 7966f319c6 ("drm/amd/display: Introduce DML2")
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When compiling with allmodconfig, gcc highlights the following error:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/display_mode_core.c: In function 'dml_core_mode_support':
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/display_mode_core.c:8229:1: error: the frame size of 2736 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
8229 | } // dml_core_mode_support
| ^
cc1: all warnings being treated as errors
This commit mitigates part of this problem by extracting the prefetch
code to its own function. After applying this commit, the stack size
reduces from 2736 to 2464, however, the stack size issue becomes part of
the new function.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Chaitanya Dhere <chaitanya.dhere@amd.com>
Fixes: 7966f319c6 ("drm/amd/display: Introduce DML2")
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
display_mode_code.c is unconditionally built with
-Wframe-larger-than=2048, which causes warnings even when
CONFIG_FRAME_WARN has been set to 0, which should show no warnings.
Use the existing $(frame_warn_flag) variable, which handles this
situation. This is basically commit 25f178bbd0 ("drm/amd/display:
Respect CONFIG_FRAME_WARN=0 in dml Makefile") but for DML2.
Fixes: 7966f319c6 ("drm/amd/display: Introduce DML2")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
./drivers/gpu/drm/amd/display/dc/dml2/display_mode_core.c:4802:84-89: WARNING: conversion to bool not needed here
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=6901
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
./drivers/gpu/drm/amd/display/dc/hwss/dce110/dce110_hwseq.c: dce110_hwseq.h is included more than once.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=6897
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn35/dcn35_fpu.c:261 dcn35_update_bw_bounding_box_fpu() warn: inconsistent indenting
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are a few spelling mistakes and an minor grammatical issue in
some dml_print messages. Fix these.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Many of the register macros defined ind dcn32_resource.h have
extra brackets. This is not conforming to the style of those
defined in other DC header files.
[How]
Remove these brackets in dcn32_resource.h
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
A critial part of "drm/amd/display: Fix windowed MPO video with ODM
combine for DCN32" is lost during promotion to upstream. This patch
addes the code back to dc.c.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 1b097bcd22.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 554340133e.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit b22c336268.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit a2830b9e85.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 30a24318cc.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit ca2b37a1c2.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 5d91801870.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit a5f9523c9c.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 01aaeb8c23.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit cd1a4bc228.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit c6d3c7b630.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 8a307777c3.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 58c3b3341c.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 5b89d2ccc8.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit f6893fcb10.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 428542d917.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit b79a00a4d4.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 77a66faacc.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit c4c182b548.
After this was commit PCON and USB4 issues were observed. A new fix will
be submitted instead.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As dc_set_power_state() no longer allocates memory, it's not necessary
to have return types and check return code as it can't fail anymore.
Change it back to `void`.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If there is memory pressure at suspend time then dynamically
allocating a large structure as part of DC suspend code will
fail.
Instead re-use the same structures and clear all members except
those that should be maintained.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2362
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm_atomic_helper_suspend() can return PTR_ERR(), in which case the
error gets stored into `dm->cached_state`. This can cause failures
during resume. Catch the error during suspend and fail the suspend
instead.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2362
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
eDPs fail to light up with seamless boot enabled
[How]
When seamless boot is enabled don't configure dpms_off
in disable_vbios_mode_if_required.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Refactor DPG test pattern logic for ODM cases
- Refactor HWSS into component folder
- Revert "drm/amd/display: Add a check for idle power optimization"
- Revert "drm/amd/display: remove duplicated edp relink to fastboot
- Update cursor limits based on SW cursor fallback limits
- Update stream mask
- Update pmfw_driver_if new structure
- Modify SMU message logs
- Don't set dpms_off for seamless boot
Known issue:
DWB (Writeback functionality) is broken.
Fix will be available in DC 3.2.256
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This could work around the issue with DP tunneling producing
a NULL pointer dereference.
[How]
Disable the virtual links.
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Enabling DPG causes HUBP to stay in blank constantly. If DPG is enabled
while an MCLK switch is taking place with SubVP, it will cause the MCLK
to never complete. This is because SubVP MCLK switch relies a HUBP
VLine interrupt, which will never occur when HUBP is constantly in
blank.
[How]
Disable SubVP when test pattern is enabled.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current DPG test pattern logic does not account for ODM configuration
changes after test pattern has already been programmed. For example, if
ODM2:1 is enabled after test pattern is already being output, the second
pipe is not programmed to output test pattern, causing half the screen
to be black.
[How]
Move DPG test pattern parameter calculations into separate function.
Whenever ODM pipe configuration changes, re-calculate DPG test pattern
parameters and program DPG if test pattern is currently enabled.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
eDPs fail to light up with seamless boot enabled
[How]
When seamless boot is enabled don't configure dpms_off
in disable_vbios_mode_if_required.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Rename hw_sequencer to hwseq.
Move all hwseq files to unique
folder hwss.
[how]
creating hwss repo in dc, and moved the dcnxx_hwseq.c
and .h files into corresponding new folders inside the hwss
and cleared the linkage errors by adding relative paths
in the Makefile.template.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Mounika Adhuri <moadhuri@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Revert commit 434cf7af49 ("drm/amd/display: Add a check for idle power optimization")
Because it cause Freesync and S4 regression
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These functions can be called from high IRQ levels and the OS will hang
if it tries to use a usleep_highres or a msleep.
[How]
Replace the fsleep with a udelay.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
For determining the cursor size limit, use the same checks that
are used for determining SW cursor fallback instead of only
using SubVP
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need to use real clock table
[How]
Update the clock table
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Whenever stream changes because of new
pipe arrangements such as ODM. The new
stream mask is not reflected in DMCUB.
The mismatch in stream mask is blocking ips
entry in some scenarios.
[How]
Whenever stream arrangement changes,
update stream mask and notify DMCUB.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Revert commit 984abb5384 ("drm/amd/display: remove duplicated edp relink to fastboot")
Because it cause 4k EDP not light up on boot
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fine tune the Vmin clock value
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
pmfw header file updated, need align with data structure.
[How]
Update the data structure.
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
FreeSync spec requires PB8 and PB12 to be set to nominal
refresh rate regardless of fixed rate or variable
[HOW]
Removed the condition that checks and overwrites max refresh rate
and set PB8/PB12 to be set to max refresh rate always
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Muhammad Ansari <muhammad.ansari@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It's important to make sure SMU messages
are logged by default to improve debugging for
power optimization use cases.
[how]
Change logs to warnings when SMU message
returns non-success id.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With S/G display becomes stable, enable S/G display for recent APUs
by default rather than white list.
v2: explicitly disable sg on pre-CZ chips (Alex)
v3: add parens for every clause (Alex)
Co-authored-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[what]
does_configuration_meet_sw_policies check was not done in the
validate_only portion of dml2, so some unsupported modes were passing bw
validation, only to fail the same check later in validate_and_build. now
we add the check to validate_only.
Also add line in dcn35_resource to ensure that value set for
enable_windowed_mpo_odm gets passed to dml.
[why]
Immediate black screen during video playback at 4k144hz. The debugger
showed that we were failing validation in dml on every updateplanes().
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update DML2 with replay vblank logic found in DML1.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are certain cases during a transition to ODM that might cause
corruption on the display. This occurs when we choose certain pipes in a
particular state.
[How]
We now will store the pipe indexes of the any pipes that might be
problematic to switch to during an ODM transition, and only use them as
a last resort.
Reviewed-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Saaem Rizvi <syedsaaem.rizvi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc->dml2_options.use_native_pstate_optimization flag will make driver
use dcn32 legacy_svp_drr related tuning. Set this to false fixed the
stutter underflow issue also based on HW suggest disable ODM by default
and let DML choose it.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Surface height/width for Chroma has another variable that it should be
intialized to, chroma_size. Fixing this will help pass DML2.0 validation
for YCbCr420 tests, DCHB006.109,129, DCHB014.011,012.
[how]
Assign SurfaceHeight/WidthC to chroma_size.height/width
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
DML2 did not carry over DML1 logic that splits pipe for stero timings. Pipe
splitting is needed in this case to pass stereo tests.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Regression from DML1.0 where we use differen DET buffer sizes for each
pipe. From the spec, we need to use DET buffer size of 384 kb for each
pipe
[how]
Ensure to use 384 kb DET buffer sizes for each available pipe.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There are cases where more than 1 stream can be mapped to the same
surface. DML2.0 does not seem to handle these cases.
[how]
Make sure to account for the stream id when deriving the plane id. By
doing this, each plane id will be unique based on the stream id.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add z8 watermarks to struct for later ASIC use.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable DML2 for DCN35.
Changes since V1:
- Remove hard coded values
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC is transitioning from DML to DML2, and this commit introduces all the
required changes for some of the already available ASICs and adds the
required code infra to support new ASICs under DML2. DML2 is also a
generated code that provides better mode verification and programming
models for software/hardware, and it enables a better way to create
validation tools. This version is more like a middle step to the
complete transition to the DML2 version.
Changes since V1:
- Alex: Fix typos
Changes since V2:
- Update DC includes
Changes since V3:
- Fix 32 bit compilation issues on x86
Changes since V4:
- Avoid compilation of DML2 on some not supported 32-bit architecture
- Update commit message
Co-developed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Co-developed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For some reason, the dml code is not guarded under CONFIG_DRM_AMD_DC_FP
in the Makefile. This commit moves the dml code under the DC_FP guard.
Reviewed-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
bw_fixed does not need any FPU operation, and it is used on DCE and DCN.
For this reason, this commit moves bw_fixed to the basic folder outside
DML.
Reviewed-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The custom_float file does not have any FPU operation, so it should be
inside DML. This commit moves the file to the basic folder.
Reviewed-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dce_calcs does not have FPU operations, and it is required for DCE and
DCN. Remove this file from the DML folder and add it to the basic folder
visible for DCE and DCN.
Reviewed-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dcn20_validate_bandwidth_fp() is invoked while FPU access has been
enabled. FPU access requires disabling preemption even on PREEMPT_RT.
It is not possible to allocate memory with disabled preemption even with
GFP_ATOMIC on PREEMPT_RT.
Move the memory allocation before FPU access is enabled.
To preserve previous "clean" state of "pipes" add a memset() before the
second invocation of dcn20_validate_bandwidth_internal() where the
variable is used.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dcn21_validate_bandwidth_fp() is invoked while FPU access has been
enabled. FPU access requires disabling preemption even on PREEMPT_RT.
It is not possible to allocate memory with disabled preemption even with
GFP_ATOMIC on PREEMPT_RT.
Move the memory allocation before FPU access is enabled.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217928
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a warning if the FPU is used from any context other than task
context. This is only precaution since the code is not able to be used
from softirq while the API allows it on x86 for instance.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The fpu_recursion_depth counter is used to ensure that dc_fpu_begin()
can be invoked multiple times while the FPU-disable function itself is
only invoked once. Also the counter part (dc_fpu_end()) is ballanced
properly.
Instead of using the get_cpu_ptr() dance around the inc it is simpler to
increment the per-CPU variable directly. Also the per-CPU variable has
to be incremented and decremented on the same CPU. This is ensured by
the inner-part which disables preemption. This is kind of not obvious,
works and the preempt-counter is touched a few times for no reason.
Disable preemption before incrementing fpu_recursion_depth for the first
time. Keep preemption disabled until dc_fpu_end() where the counter is
decremented making it obvious that the preemption has to stay disabled
while the counter is non-zero.
Use simple inc/dec functions.
Remove the nested preempt_disable/enable functions which are now not
needed.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is a revert of the commit mentioned below while it is not wrong, as
in the kernel will explode, having migrate_disable() here it is
complete waste of resources.
Additionally commit message is plain wrong the review tag does not make
it any better. The migrate_disable() interface has a fat comment
describing it and it includes the word "undesired" in the headline which
should tickle people to read it before using it.
Initially I assumed it is worded too harsh but now I beg to differ.
The reviewer of the original commit, even not understanding what
migrate_disable() does should ask the following:
- migrate_disable() is added only to the CONFIG_X86 block and it claims
to protect fpu_recursion_depth. Why are the other the architectures
excluded?
- migrate_disable() is added after fpu_recursion_depth was modified.
Shouldn't it be added before the modification or referencing takes
place?
Moving on.
Disabling preemption DOES prevent CPU migration. A task, that can not be
pushed away from the CPU by the scheduler (due to disabled preemption)
can not be pushed or migrated to another CPU.
Disabling migration DOES NOT ensure consistency of per-CPU variables. It
only ensures that the task acts always on the same per-CPU variable. The
task remains preemptible meaning multiple tasks can access the same
per-CPU variable. This in turn leads to inconsistency for the statement
*pcpu -= 1;
with two tasks on one CPU and a preemption point during the RMW
operation:
Task A Task B
read pcpu to reg # 0
inc reg # 0 -> 1
read pcpu to reg # 0
inc reg # 0 -> 1
write reg to pcpu # 1
write reg to pcpu # 1
At the end pcpu reads 1 but should read 2 instead. Boom.
get_cpu_ptr() already contains a preempt_disable() statement. That means
that the per-CPU variable can only be referenced by a single task which
is currently running. The only inconsistency that can occur if the
variable is additionally accessed from an interrupt.
Remove migrate_disable/enable() from dc_fpu_begin/end().
Cc: Tianci Yin <tianci.yin@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Fixes: 0c316556d1 ("drm/amd/display: Disable migration to ensure consistency of per-CPU variable")
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unplug mst hub will cause warning. That's because
dm_helpers_construct_old_payload() is changed to be called after
payload removement from dc link.
In dm_helpers_construct_old_payload(), We refer to the vcpi in
payload allocation table of dc link to construct the old payload
and payload is no longer in the table when we call the function
now.
[How]
Refer to the mst_state to construct the number of time slot for old
payload now. Note that dm_helpers_construct_old_payload() is just
a quick workaround before and we are going to abandon it soon.
Fixes: 5aa1dfcdf0 ("drm/mst: Refactor the flow for payload allocation/removement")
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231005080405.169841-1-Wayne.Lin@amd.com
[Why]
The edge-case DISPCLK WDIVIDER changes call stream_enc functions.
But with MPC pipes, downstream pipes have null stream_enc and will
cause crash.
[How]
Only call stream_enc functions for pipes that are OTG master.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC v3.2.254
* Stability fixes through null pointer checks, blackscreen fixes on
certain configurations
* Improvements for various functionality like Idle optimization, ILR, DSC, IPS
* Fixes for ILR functionality
* Trivial code cleanups
===================================================================
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Make some formatting changes and rearranging of definitions for consistency.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
* Add hints about the bits used in the packed struct.
* Update new bitfields for ABM and IPS
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need a helper function to check idle power is allowed
so that dc doesn't access any registers that are power-gated.
[how]
Implement helper function to check idle power optimization.
Enable a hook to check if detection is allowed.
Signed-off-by: Sung Joon Kim <Sungjoon.Kim@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Clip size increase will increase viewport, which could cause us to
switch to MPC combine.
If we skip full update, we are not able to change to MPC combine in
fast update. This will cause corruption showing on the video plane.
[how]
treat clip size increase of a surface larger than 5k as a full update.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Fix constness of string parameters
- Fix zero-initialization of structs which cannot take a 0 literal as the
first field, for example enums
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Driver needs to be compatible with PM FW that doesn't support IPS
[how]
Toggle internal control flag
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current ILR toggle is on/off as a part of panel
config for new function, which breaks original
ILR logic
[How]
Refactor ILR and take panel config into account
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Sherry Wang <yao.wang1@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
enable_accelerated_mode function is fully to check
whether fastboot support or not.
It is no longer to disable_vbios_mode_if_required.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The edge-case DISPCLK WDIVIDER changes call stream_enc functions.
But with MPC pipes, downstream pipes have null stream_enc and will
cause crash.
[How]
Only call stream_enc functions for pipes that are OTG master.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
need to enable dsc_clk regardless dsc_pg
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[what and why]
Check whether dpp resource pointer is null in advance and return early
if so.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Martin Leung <martin.leung@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If no plane was newly enabled or changed scaling, there can be no new
scaling mismatch with the cursor plane.
By not pulling non-cursor plane states into all atomic commits while
the cursor plane is enabled, this avoids synchronizing all cursor plane
changes to vertical blank, which caused the following IGT tests to fail:
kms_cursor_legacy@cursor-vs-flip.*
kms_cursor_legacy@flip-vs-cursor.*
Fixes: 003048ddf4 ("drm/amd/display: Check all enabled planes in dm_check_crtc_cursor")
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 44e60b14d5.
Since, it causes a regression in which eDP displays with PSR support,
but no Replay support (Sink support <= 0x03), fail to enable PSR and
consequently all IGT amd_psr tests fail. So, revert this until a more
suitable fix can be found.
Cc: stable@vger.kernel.org
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Ivan Lipski <ivlipski@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cleanup, no functional change intended.
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Fix following problems:
- In abm config, forget to initialize config.ambient_thresholds_lux.
- Adjust the coding style problem
- Restrict to call psr_su_set_dsc_slice_height() under edp only
Reviewed-by: Robin Chen <robin.chen@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
drm_writeback requires to capture exact one frame in each writeback
call.
[HOW]
frame_capture is disabled after each writeback is completed.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Add a function to enable and disable DWB's frame captures.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Hardware may require different warmup approaches - big buffer or
individual buffers.
[HOW]
Setup warmup for big buffer when it is required by specific hardware.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Add a new field to keep track whether a crtc is previously
writeback-enabled.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Counter j was not updated to present the num of writeback_info when
writeback pipes are removed.
[HOW]
update j (num of writeback info) under the correct condition.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
hw_points_num is 0 before ogam LUT is programmed; however, function
"dwb3_program_ogam_pwl" assumes hw_points_num is always greater than 0,
i.e. substracting it by 1 as an array index.
[HOW]
Check hw_points_num is not equal to 0 before using it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
wb_enabled field is set to false before it is used, and the following
code will never be executed.
[HOW]
Setting wb_enable to false after all removal work is completed.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
The enable and disable writeback calls need to be included in the
coressponding functions in dc_stream.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Handle writeback requests and fill in the required information for DWB
programming and setup.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Writeback connectors don't have a physical sink but DC still
needs a sink to function. Create a fake sink and stream for
writeback connectors
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We need to track the dc_link and it would get confusing if
re-using the amdgpu_dm_connector.
[HOW]
Creating new amdgpu_dm_wb_connector.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Again, we need to use this function for writeback connectors,
which are not of type amdgpu_dm_connector. Use the common base
drm_connector instead.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:3928: warning: Function parameter or member 'srf_updates' not described in 'could_mpcc_tree_change_for_active_pipes'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
We need to use this function for both amdgpu_dm_connectors
and drm_writeback_connectors. Modify it to operate on
a drm_connector as a common base.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We will be dealing with two types of connector: amdgpu_dm_connector
and drm_writeback_connector.
[HOW]
We want to find both and then cast to the appriopriate type afterwards.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-misc-next for v6.7-rc1:
UAPI Changes:
- drm_file owner is now updated during use, in the case of a drm fd
opened by the display server for a client, the correct owner is
displayed.
- Qaic gains support for the QAIC_DETACH_SLICE_BO ioctl to allow bo
recycling.
Cross-subsystem Changes:
- Disable boot logo for au1200fb, mmpfb and unexport logo helpers.
Only fbcon should manage display of logo.
- Update freescale in MAINTAINERS.
- Add some bridge files to bridge in MAINTAINERS.
- Update gma500 driver repo in MAINTAINERS to point to drm-misc.
Core Changes:
- Move size computations to drm buddy allocator.
- Make drm_atomic_helper_shutdown(NULL) a nop.
- Assorted small fixes in drm_debugfs, DP-MST payload addition error handling.
- Fix DRM_BRIDGE_ATTACH_NO_CONNECTOR handling.
- Handle bad (h/v)sync_end in EDID by clipping to htotal.
- Build GPUVM as a module.
Driver Changes:
- Simple drivers don't need to cache prepared result.
- Call drm_atomic_helper_shutdown() in shutdown/unbind for a whole lot
more drm drivers.
- Assorted small fixes in amdgpu, ssd130x, bridge/it6621, accel/qaic,
nouveau, tc358768.
- Add NV12 for komeda writeback.
- Add arbitration lost event to synopsis/dw-hdmi-cec.
- Speed up s/r in nouveau by not restoring some big bo's.
- Assorted nouveau display rework in preparation for GSP-RM,
especially related to how the modeset sequence works and
the DP sequence in relation to link training.
- Update anx7816 panel.
- Support NVSYNC and NHSYNC in tegra.
- Allow multiple power domains in simple driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f1fae5eb-25b8-192a-9a53-215e1184ce81@linux.intel.com
[WHY]
Writeback connectors are based on a different object:
drm_writeback_connector, and are therefore different from
amdgpu_dm_connector. We need to be careful to ensure code
designed for amdgpu_dm_connector doesn't inadvertently try
to operate on a drm_writeback_connector.
[HOW]
Skip them when connector type is DRM_MODE_CONNECTOR_WRITEBACK.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It was only checking planes which had any state changes in the same
commit. However, it also needs to check other enabled planes.
Not doing this meant that a commit might spuriously "succeed", resulting
in the cursor plane displaying with incorrect scaling. See
https://gitlab.gnome.org/GNOME/mutter/-/merge_requests/3177#note_1824263
for an example.
Fixes: d1bfbe8a32 ("amd/display: check cursor plane matches underlying plane")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Create a drm_writeback_connector when connector signal equals
SIGNAL_TYPE_VIRTUAL.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch fixes a null pointer dereference in the error message that is
printed when the Display Core (DC) fails to initialize. The original
message includes the DC version number, which is undefined if the DC is
not initialized.
Fixes: 9788d087ca ("drm/amd/display: improve the message printed when loading DC")
Signed-off-by: Cong Liu <liucong2@kylinos.cn>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Prepare a virtual connector for writeback.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
These DPCD addresses are either declared in other header files
where it makes more sense or simply not used by any DC code.
Remove them to reduce redundancies and potential confusion.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Previously this only excluded build for a few amdgpu_dm
binaries which makes no sense.
[HOW]
Wrap the entire Makefile in "ifneq ($(CONFIG_DRM_AMD_DC),)"
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The error path for DMUB firmware loading is unnecessarily noisy.
When a firmware is missing 3 errors show up:
```
amdgpu 0000:07:00.0: Direct firmware load for amdgpu/green_sardine_dmcub.bin failed with error -2
[drm:dm_early_init [amdgpu]] *ERROR* DMUB firmware loading failed: -19
[drm:amdgpu_device_init [amdgpu]] *ERROR* early_init of IP block <dm> failed -19
```
The error code for the device init is bubbled up already, remove the
second one.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC code is reused by other OSes and so Linux return codes don't
make sense. Change dc_set_power_state() to boolean and add a wrapper
dm_set_power_state() to return a Linux error code for the memory
allocation failure.
Suggested-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During the suspend process dc_set_power_state() will use kzalloc
to allocate memory, but this potentially fails with memory pressure.
If it fails, the suspend should be aborted.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2362
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: Harry.Wentland@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc->caps.color.mpc.gamut_remap says there is a post-blending color block
for gamut remap matrix for DCN3 HW family and newer versions. However,
those drivers still follow DCN10 programming that remap stream
gamut_remap_matrix to DPP (pre-blending).
To enable pre-blending and post-blending gamut_remap matrix supports at
the same time, set stream gamut_remap to MPC and plane gamut_remap to
DPP for DCN families that support both.
It was tested using IGT KMS color tests for DRM CRTC CTM property and it
preserves test results.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To disable AGP, the start needs to be set to a higher
value than the end. Set a default disable value for
the AGP aperture and allow the IP specific GMC code
to enable it selectively be calling amdgpu_gmc_agp_location().
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
After repopulating pipes for a split / merge, we want to find the
lowest vlevel that supports the desired mpc combine level.
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Change to new interface for notifying OS of cursor support changes
Reviewed-by: Gang Chu <gang.chu@amd.com>
Reviewed-by: Jaina Han <jaina.han@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Hong-lu Cheng <hong-lu.cheng@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Allow dc report maximum display clock possible at vmin
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along the following:
- Fix incorrect odm change detection logic
- Add primary pipe check when building slice table for dcn3x
- Add get primary dpp pipe resource interface
- Add missing function pointer for DCN321 resource
- Rename DisableMinDispClkODM in dc_config
- Break after finding supported vlevel for repopulate
- Update OPP counter from new interface
- Augment display clock in dc_cap structure
- Improve code style on bios_parser2
- Skip audio config for virtual signal
- Block MPO if it prevents pstate support
- Fix DP2.0 timing sync
- Improve x86 and dmub ips handshake
- Remove guaranteed viewports limitation for odm
- Add new windowed mpo odm minimal transition sequence
- Reset stream slice count for new ODM policy
- Determine fast update only before commit minimal transition state
- Remove unused mmhub_reg_offsets
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current ODM change detection only compares first two ODM slices.
If there are 4 ODM slices and the change is within the last two slices, the
logic fails to detect ODM change and cause us to skip ODM programming
unexpectedly.
[how]
Add a is ODM topology changed resource interface to check any ODM
topology changes with a more generic method.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is a corner use case where the same plane pointer can be added into
dc state twice. In addition to plane state pointer check we also need to match
primary pipe before identifying the same plane.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need to have a helper function to find the primary dp pipe of the plane
associated with a dpp pipe
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
acquire_free_pipe_as_secondary_opp_head function pointer is not
assigned. This causes ODM mode to be disabled after enabling
windowed MPO ODM capability on DCN321.
[how]
assign the correct function to the function pointer.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[what and why]
The logic for DisableMinDispClkODM is reversed now that odm is
disabled by default. Renaming to EnableMinDispClkODM.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
bios_parser2 uses space instead of tabs in multiple areas; this commit
converts those spaces into tabs. It also removes some other small
details.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
edid_override and drm_edid_override_connector_update, according to drm
documentation, should not be referred outside drm_edid.
[HOW]
Remove and replace them accordingly. This can tested by IGT's
kms_hdmi_inject test.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For multi-GPU systems it is difficult to tell which GPU a particular
message is being printed for and that is undesirable because it
complicates debugging efforts. Also, the new macros allow us to enable
logging for particular parts of the codebase more selectively (since we
no longer need to throw everything at DRM_DEBUG_KMS()). So, for the
reasons outlined above we should switch to the new macros.
We can accomplish this by using the existing DC_LOGGER code to pass
around the relevant `struct drm_device` which will be fed to the new
macros in logger_types.h. Also, we must get rid of all instances of the
DC_LOG_.*() functions that are currently in amdgpu_dm since we don't use
the DC logger there and we can simply refer to the macros directly
there instead.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
IGT's kms_hdmi_inject (subtest inject_audio) triggers a warning message
from dce_aud_az_configure. This can be fixed by checking Virtual signal
that does not need to configure AZ audio since it does not have any.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change adds a method to block mpo when it would cause us to
exit pstate support. We should block mpo by default where MPO
causes issues by preventing pstate change.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Triggering OTG sync before all OTG/HPO clock programming is complete
causes timing sync to fail and a subsequent P-state hang.
[How]
Move DTB clock programming earlier in the sequence to
enable_stream_timing.
Reviewed-by: Ariel Bernstein <eric.bernstein@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a race condition between x86 and dmcub fw when attempting to exit
IPS2. Scenarios including exiting IPS2 before IPS2 has been entered. This
can cause unexpected hang when DMCUB attempt to exit while PMFW still
tries to enter IPS2.
[How]
A new design has been introduced to remove race conditions and improve the
handshake between x86 and DMCUB. An AON scratch register is borrowed from
PMFW to determine whether DMCUB has committed to IPS entry or not.
In the case when dmcub has committed IPS entry, x86 must poll until an exit
event occurred either from DMCUB(IPS1) or PMFW(IPS2). x86 will wait
upperbound of evaluation and IPS entry time to ensure IPS2 exit event has
been sent to PMFW.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
With the more generic hw minimal state transition sequence,
this limitation has been overcome.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We do not have a programming sequence to support seamless transition
between MPC combine to ODM combine when plane count remains the same.
This can happen with windowed MPO ODM use cases when plane scaling
is changed over ODM Combine's capability.
[How]
We are adding a programming sequence specifically to handle the transition
between MPC combine and ODM combine during plane scaling change.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
ODM combine could prevent us from supporting more planes
we will reset ODM slice count back to 1 when all planes have
been removed to maximize the amount of planes supported when
new planes are added.
[how]
reset ODM slice count when all planes are removed.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
commit minimal transition state would update current
state to new state with surface and stream update
applied. If we determine fast update only after we
have committed the minimal transition state based on
new state, we will skip committing the full new state.
[how]
determine fast update only earlier based on the
actaul currents state. Only skip full commit when
the transition between actual current state and new
state is fast update only.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
mmhub_reg_offsets never used in code. Remove it.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes a few style issues:
- Only calculate the dto_params and dp_hpo_inst when dccg is present.
- Fix indentation
- Drop empty else block
Fixes: 7f7925e258 ("drm/amd/display: Fix MST recognizes connected displays as one")
Cc: Muhammad Ahmed <ahmed.ahmed@amd.com>
Cc: Michel Dänzer <michel@daenzer.net>
Cc: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix kernel-doc warnings discovered in AMD gpu display driver.
Fixes these warnings:
./drivers/gpu/drm/amd/display/dc/inc/hw/mpc.h:110: warning:
Function parameter or member 'overlap_only'
not described in 'mpcc_blnd_cfg'.
./drivers/gpu/drm/amd/display/dc/inc/hw/mpc.h:110: warning:
Function parameter or member 'bottom_gain_mode'
not described in 'mpcc_blnd_cfg'.
./drivers/gpu/drm/amd/display/dc/inc/hw/mpc.h:110: warning:
Function parameter or member 'background_color_bpc'
not described in 'mpcc_blnd_cfg'.
./drivers/gpu/drm/amd/display/dc/inc/hw/mpc.h:110:
warning: Function parameter or member 'top_gain'
not described in 'mpcc_blnd_cfg'.
./drivers/gpu/drm/amd/display/dc/inc/hw/mpc.h:110:
warning: Function parameter or member 'bottom_inside_gain'
not described in 'mpcc_blnd_cfg'.
./drivers/gpu/drm/amd/display/dc/inc/hw/mpc.h:110:
warning: Function parameter or member 'bottom_outside_gain'
not described in 'mpcc_blnd_cfg'.
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Swarup Laxman Kotiaklapudi <swarupkotikalapudi@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along the following:
- Use optc32 instead of optc30 in DC
- Optimize OLED T7 delay
- Multiple fixes for MST, register mas, and others
- Update driver and IPS interop
- Improve z8 watermark mask
- DCN35 updates
- Enable replay for DCN35
- Temporarily disable clock gating
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are multiple parts of the code that DC does not use anymore, and
this commit drops those dead codes.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable DCN low mem power by default.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update with extended blank Vstartup adjustment for replay.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change DC to use optc32, which uses REG_UPDATE instead of REG_SET.
REG_SET clears OTG_H_TIMING_DIV_MODE_MANUAL which must be set to 1 in
some specific HDMI configurations.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver doesn't need T7 delay for OLED panels, since it doesn't control
power sequence.
[How]
This delay can be skipped to optimize resume times.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-misc-next for v6.7-rc1:
UAPI Changes:
- Nouveau changed to not set NO_PREFETCH flag explicitly.
Cross-subsystem Changes:
- Update documentation of dma-buf intro and uapi.
- fbdev/sbus fixes.
- Use initializer macros in a lot of fbdev drivers.
- Add Boris Brezillon as Panfrost driver maintainer.
- Add Jessica Zhang as drm/panel reviewer.
- Make more fbdev drivers use fb_ops helpers for deferred io.
- Small hid trailing whitespace fix.
- Use fb_ops in hid/picolcd
Core Changes:
- Assorted small fixes to ttm tests, drm/mst.
- Documentation updates to bridge.
- Add kunit tests for some drm_fb functions.
- Rework drm_debugfs implementation.
- Update xe documentation to mark todos as completed.
Driver Changes:
- Add support to rockchip for rv1126 mipi-dsi and vop.
- Assorted small fixes to nouveau, bridge/samsung-dsim,
bridge/lvds-codec, loongson, rockchip, panfrost, gma500, repaper,
komeda, virtio, ssd130x.
- Add support for simple panels Mitsubishi AA084XE01,
JDI LPM102A188A,
- Documentation updates to accel/ivpu.
- Some nouveau scheduling/fence fixes.
- Power management related fixes and other fixes to ivpu.
- Assorted bridge/it66121 fixes.
- Make platform drivers return void in remove() callback.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3da6554b-3b47-fe7d-c4ea-21f4f819dbb6@linux.intel.com
On eDP we can receive invalid modes from dm_update_crtc_state() for
entirely new streams for which drm_mode_set_crtcinfo() shouldn't be
called on. So, instead of calling drm_mode_set_crtcinfo() from within
create_stream_for_sink() we can instead call it from
amdgpu_dm_connector_mode_valid(). Since, we are guaranteed to only call
drm_mode_set_crtcinfo() for valid modes from that function (invalid
modes are rejected by that callback) and that is the only user
of create_validate_stream_for_sink() that we need to call
drm_mode_set_crtcinfo() for (as before commit cb841d27b8
("drm/amd/display: Always pass connector_state to stream validation"),
that is the only place where create_validate_stream_for_sink()'s
dm_state was NULL).
Cc: stable@vger.kernel.org
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2693
Fixes: cb841d27b8 ("drm/amd/display: Always pass connector_state to stream validation")
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[What]
MST now recognizes both connected displays
Fixes: 927e784c18 ("drm/amd/display: Add symclk enable/disable during stream enable/disable")
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add new IPS ALLOW masks
- Add new Replay power configuration options
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MST now recognizes both connected displays
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix some non-initialized register mask and update golden setting.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable the display replay feature for DCN35.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a config option to disable odm dispclk optimization for debug
purpose.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disable IPS by default till it is ready.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently, driver is not aware if IPS is supported. After PMFW helps
implement new message query functionality, driver will set IPS
capability flag.
[how]
Create new SMU hook function to query IPS capability. Based on the cap,
set appropriate flags to false for power-gating purposes. This will
avoid keeping SMU busy and offloading tasks to DMUB/driver.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Two issues fixed:
1. Currently, driver does not allow idle prior to PSR entry. Once
PSR1+IPS is enabled, there is intermittent hang due to DCN access
from IrqMgr during IPS2.
2. Driver is sending multiple commands to PMFW and dmcub to exit IPS
even during IPS0.
[How]
1. Set driver allow optimization prior to entering PSR mode with the
condition for eDP display only. Unregister all interrupts before
allowing driver idle and re-register interrupts when exiting from
idle. This will prevent IrqMgr to access DCN during IPS2.
2. Block sending PMFW and dmcub exit low power state commands when
driver is not in idle state.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correct z8_watermark mask from 16bit to 20bit. Also, do not set dcn35
dprefclk in clk_mgr_construct.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The STREAM_MAPPER_CONTROL register offset was left uninitialized,
causing warning in the driver log at runtime
[How]
A temporary solution to add it into dcn35_create_resource_pool.
[TODO]
Remove duplication between SE_DCN35_REG_LIST_RI in dcn35_resource.h and
SE_DCN35_REG_LIST in dcn35_dio_stream_encoder.h
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Artem Grishin <artem.grishin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pipe resource interfaces were changed.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For DPIA we should have preferred DIG assignment based on DPIA selected
as per the ASIC design
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Mustapha Ghaddar <mghaddar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
set_static_screen_control has been updated for DCN3 series. Update it
for DCN35.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Sung-huai Wang <danny.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Call to immediate_disable_crtc was not checked before calling, exposing
a potential null pointer hang.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
PMFW ungate this feature, this can be enabled now
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add z8 watermarks to struct for DCN35.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some of the stream encoder registers have register offset address 0. It
is causing no display in some scenarios due to DIG_FE was not setup
correctly and was not enabled.
[How]
Fix stream encoder register define list.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On eDP we can receive invalid modes from dm_update_crtc_state() for
entirely new streams for which drm_mode_set_crtcinfo() shouldn't be
called on. So, instead of calling drm_mode_set_crtcinfo() from within
create_stream_for_sink() we can instead call it from
amdgpu_dm_connector_mode_valid(). Since, we are guaranteed to only call
drm_mode_set_crtcinfo() for valid modes from that function (invalid
modes are rejected by that callback) and that is the only user
of create_validate_stream_for_sink() that we need to call
drm_mode_set_crtcinfo() for (as before commit cb841d27b8
("drm/amd/display: Always pass connector_state to stream validation"),
that is the only place where create_validate_stream_for_sink()'s
dm_state was NULL).
Cc: stable@vger.kernel.org
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2693
Fixes: cb841d27b8 ("drm/amd/display: Always pass connector_state to stream validation")
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Temporarily disable dchubbub clock gating, registers:
.DISPCLK_R_DCHUBBUB_GATE_DIS
.DCFCLK_R_DCHUBBUB_GATE_DIS
need to follow up with sequence issue.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Leo Chen <sanchuan.chen@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disable clock gating logic.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
