We will check if any hidden SSID found in passive scan channels
and do specific SSID active scan for those channels.
Signed-off-by: chunfan chen <jeffc@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to handle multichannel event from FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to advetise mwifiex multichannel support to
cfg80211. If module parameter drcs is enabled and FW supports multichannel
operation we advertise this support to cfg80211. As of now 2 simultaneous
channels are supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to extend TX Data pause for AP intefaces.
Also for station role, support for pausing/unpausing all traffic
when mac address parameter is BSSID is added.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to enable data traffic only when port is open.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for another TX queue in driver- bypass
TX queue. This queue is used for sending data/mgmt packets while
in disconnected state i.e. when port is yet not unblocked.
TDLS setup packets would also be queued in this queue.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It was observed that AP beacons would not reflect correct regulatory
information upon starting AP in A band. This was because of missing
AP config band update in set_channel of start_ap. Also we configure 11D
settings info FW only for specific band. So we need to download domain
info to FW even if domain remains unchanged but band is changed.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TDLS link status - channel switching, off channel or base channel itself
indicates that TDLS link is setup.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add support for a new tdls configuration command
which is used for configuration of tdls channel switch parameters.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add new tdls status used for tdls channel switch.
Driver in turn would block cmd path and data path if tdls
channel switching. Data path to non tdls peer should be blocked
if tdls channel switch to off-channel.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to enable TX data pause feature for mwifiex.
Whenever FW TX buffers reach threshold, FW would send TX pause event
to driver. Driver in turn would block data traffic to that particular
receiver address.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If timeshare coexistance between bluetooth and WLAN gets enabled,
firmware will give host an event to reduce Rx AMPDU BA window size.
The event is handled in this patch.
Signed-off-by: Chunfan Chen <jeffc@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to parse power constraint IEs from
Tail buffer. This power constraint is then set to FW during
bss_config download.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch maintain statistic information for the stations associated
to the mwifiex micro AP, include tx/rx bytes/packets, signal strength,
tx bitrate.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add cfg80211 get_channel handler for mwifiex.
The handler will be used to report current channel to upper
layer utility.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to disable ongoing CAC in FW upon
detecting radar during CAC period.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently device dump generated in the driver is retrieved
using ethtool set/get dump commands. We will get rid of
ethtool approach and use devcoredump framework.
Device dump can be trigger by
cat /debugfs/mwifiex/mlanX/device_dump
and when the dump operation is completed, data can be read by
cat /sys/class/devcoredump/devcdX/data
We have prepared following script to split device dump data
into multiple files.
[root]# cat mwifiex_split_dump_data.sh
#!/bin/bash
# usage: ./mwifiex_split_dump_data.sh dump_data
fw_dump_data=$1
mem_type="driverinfo ITCM DTCM SQRAM APU CIU ICU MAC"
for name in ${mem_type[@]}
do
sed -n "/Start dump $name/,/End dump/p" $fw_dump_data > tmp.$name.log
if [ ! -s tmp.$name.log ]
then
rm -rf tmp.$name.log
else
#Remove the describle info "Start dump" and "End dump"
sed '1d' tmp.$name.log | sed '$d' > /data/$name.log
if [ -s /data/$name.log ]
then
echo "generate /data/$name.log"
else
sed '1d' tmp.$name.log | sed '$d' > /var/$name.log
echo "generate /var/$name.log"
fi
rm -rf tmp.$name.log
fi
done
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently we are dumping driver information also inside
firmware dump API. We will call it as device dump and
dump driver and firmware data separately.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch is to add support for data hexdump debug feature.
It is controlled by level debug_mask in adapter structure.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for debugging print control in mwifiex driver.
The debug level can be controlled via either by modules load parameter
debug_mask or by writing to debug_mask in debugfs file.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for FW memory read/write operations via debugfs.
This is useful during debugging FW issues.
Examples:
For reading FW memory location:
echo r 0x01ac > /sys/kernel/debug/mwifiex/mlan0/memrw
cat /sys/kernel/debug/mwifiex/mlan0/memrw
For writing FW memory location:
echo w 0x01ac 0x55aa > /sys/kernel/debug/mwifiex/mlan0/memrw
Signed-off-by: Chin-ran Lo <crlo@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath9k:
* add Active Interference Cancellation, a method implemented in the HW
to counter WLAN RX > sensitivity degradation when BT is transmitting
at the same time. This feature is supported by cards like WB222
based on AR9462.
iwlwifi:
* Location Aware Regulatory was added by Arik
* 8000 device family work
* update to the BT Coex firmware API
brmcfmac:
* add new BCM43455 and BCM43457 SDIO device support
* add new BCM43430 SDIO device support
wil6210:
* take care of AP bridging
* fix NAPI behavior
* found approach to achieve 4*n+2 alignment of Rx frames
rt2x00:
* add new rt2800usb device DWA 130
rtlwifi:
* add USB ID for D-Link DWA-131
* add USB ID ASUS N10 WiFi dongle
mwifiex:
* throughput enhancements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVHATOAAoJEG4XJFUm622b4EsIAIMGOLb2GuqtxpN/Ei1TmUFV
8B3KTLmeau/glqxquySQ2mIthDqijesbl0jyKWJP/+ZsXhjhpagXAIMw6E5KH3HN
1XKCvyqbkGScTcheaS4HYFmKKoM0OlPnDKhybYtPiScW2kyQf8S9msbeEzLdYYen
qYKMRq/J/QuobWvtapyGOBtyuVtuTrKuP8LzKQX9JAyKtM2si/iOvG7EiFmcAcis
DGJBrwhy/i6oBoi6e6KGgxIpXJE9WHsMs2QBYpFkxV2SbzXTOyq1EMFJvMHCq927
QfEsgOgAyVLfsXqN1uNK49eJtTuWRuJehEV88xjUbMXcYQNiaKdnYY6KvIBQ7XU=
=POsk
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-04-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
ath9k:
* add Active Interference Cancellation, a method implemented in the HW
to counter WLAN RX > sensitivity degradation when BT is transmitting
at the same time. This feature is supported by cards like WB222
based on AR9462.
iwlwifi:
* Location Aware Regulatory was added by Arik
* 8000 device family work
* update to the BT Coex firmware API
brmcfmac:
* add new BCM43455 and BCM43457 SDIO device support
* add new BCM43430 SDIO device support
wil6210:
* take care of AP bridging
* fix NAPI behavior
* found approach to achieve 4*n+2 alignment of Rx frames
rt2x00:
* add new rt2800usb device DWA 130
rtlwifi:
* add USB ID for D-Link DWA-131
* add USB ID ASUS N10 WiFi dongle
mwifiex:
* throughput enhancements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJVGWlNAAoJEDBSmw7B7bqr5s8P/R9+Q6y4Ixice9dDOJYynl/d
dMEUEfCBWUyDaQD1bNQIED2mc0sM5+Ax8OVIVx9fdrLGPxaISBqDJKE1USoTNZzm
q+U3dM4Q45SfQSsgaY4FtxTlPWPtUKsNMXY/CxLR+IqVeA3+30rX+hv1f3SAqBj0
68IwW/uUIHb71IZ+hz2Mwudt4JVW8KRg9VlZ0UY6EEvC4m5QD2YkwQQo/hJ2WF+/
wAJbku02L/Vy4J7E6hNcKYWXokht4fVYphjl/1ZDd/+8L8SUv9mC88n1Jzxa428p
1PmbtwzbpOrtTcC2BCPDA04IyfMc7k9DlLKw/h2KLPbHZXheD9eVmo/Am5vz+uH6
926f+FK339SzoJnZ5wBBDiZ8W8TLYNc8ImxtcxjnrtGfr1CKiuh23P1CWyOlKJCO
BYFJqkCOqWOHYnN0embaj7JqM/LmQI5ZoBZHZhD2KQXIXpTsjjIMPfJvip5D+tsV
+iXIlQwdeK6rbjxdonBgn7n57XIeSVMAYeyDCbzIShfibjHbUZPn+RsZCtv8RWv8
EaZu8PerU5ZDKwdX940+lWrtf/TMDJBYQpAIBRuiZK4DTNWCt3BrDlvb1FXGgA+X
vQJnr32vjJ/pLDxNLHQlkKWC4I/CYtG47OgcJN9AQXrig1zApd+C29zy3aqch3ea
wxV9dFfheTqZFjtZfSsH
=O/cf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Lots of updates for net-next; along with the usual flurry
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This will expose in /sys whether the ifname of a device is set by
userspace or generated by the kernel. The latter kind (wlanX, etc)
is not deterministic, so userspace needs to rename these devices
to names that are guaranteed to stay the same between reboots. The
former, however should never be renamed, so userspace needs to be
able to reliably tell the difference.
Similar functionality was introduced for the rtnetlink core in
commit 5517750f05 ("net: rtnetlink - make create_link take name_assign_type")
Signed-off-by: Tom Gundersen <teg@jklm.no>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
[reformat changelog to fit 72 cols]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SDIO reset was not happening properly on mwifiex as cancel_work_sync
in mwifiex_sdio_remove used to kill the calling work function itself.
Due to this, the interface was not getting removed and card was not
getting added again. Reset work function has been made independent
of adapter variable and cancel_work_sync has been moved to cleanup
function.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch brings in support for SDIO single port rx aggregation
to mwifiex.
Maximum read size support by SDIO cmd53 is 64K.
Based on multi port aggregation which is already part of mwifiex, idea here
is multiple packets received in FW can be aggregated into single buffer.
A separate upload type is defined for such packet aggregated to single port.
Packets from this single buffer are later deaggregated into individual packets.
This way, driver can receive more packets each time through single SDIO cmd53;
thereby reducing no of times MMC bus is accessed.
SDIO SP aggregation support is advertised by FW during load time and driver
would get FW block size in command response of HostCmd_CMD_SDIO_SP_RX_AGGR_CFG.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During profiling, we discovered that driver remains idle for time
when pakcet is downloaded to FW but no TX_DONE has been received
i.e. while data_sent is true.
This patch adds enhancement to TX routine where we preprocess
packets from TX queue, make them ready for TX and add them to
separate TX queue.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Chin-ran Lo <crlo@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch removes BA setup helper routines
mwifiex_is_bastream_setup and mwifiex_is_amsdu_in_ampdu_allowed.
Current code will use two functions to check bastream setup and
amsdu in ampdu. This patch change these functions to flags, thus
avoiding redundant spin_lock check while dequeuing TX packets.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current code does not check whether main_work_queue or
rx_work_queue is running when preparing to do queue_work,
this code fix add check before calling queue_work, reducing
unnecessary queue_work switch.
This change instead sets more_task flag to ensure we run main_process
superloop once again.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename this function to reflect its purpose correctly.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A crash was detected while changing virtual interface type is in
progress. This was tracked to race condition in accessing bss_priority
table while change is in progress. This patch ensures that main_process
and rx_process works are locked while we change virtual interface.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for auto ARP feature in mwifiex.
The device will respond to ARP requests from the network
with ARP response in suspended state without waking up the host.
This feature is enabled in the driver by default.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for DMA alignment of sk_buffs
allocated for RX.
Patch also adds support to modify skb allocation flags.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch handles a corner case where TX packet would remain in
driver queue till next packet comes in.
Here is sequence:
1. TX packet is queued via hard_start_xmit and main_work is queued
2. SDIO interrupt comes in which directly call mwifiex_main_process.
This starts executing main superloop.
3. Now work from step1 is scheduled but at first check itself it sees
mwifiex_processing is set and exits.
4. Now if superloop from step2 has passed TX processing part of superloop
this packet would remain in queue until next packet/command/SDIO interrupt
arrives and queues main_work.
This patch fixes this corner case by defining more_task flag which is set when
mwifiex_processing is found to be true. At end of superloop we again check if
more_task flag is set and if set, execute superloop again.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch enables 11h extensions in FW upon detecting DFS
channel in start radar detection/channel switch handlers.
Patch also takes care of disabling 11h when non DFS channels
are to be set during start_ap handler.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds cfg80211 channel_switch support for mwifiex.
Upon receiving channel switch request, driver would parse channel
switch announcement IE from beacon_data.
If TX is blocked, netdev queues are stopped. IEs from csa_beacon
are then parsed and set to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for radar_detected event from FW.
Driver in turn would stop netdev queues to stop TX traffic and
issue RADAR_DETECT event to cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for channel report enabling.
Channel report event happens if radar is detected on specified channel
after driver has issued radar detect command within CAC time.
Driver in turn sends RADAR_DETECTED event to cfg80211 to tell radar was
detected within CAC time.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for cfg80211 start_radar_detection handler.
Upon reception of start_radar_detection, driver prepares radar detect
command to FW.
Delayed work is queued for CAC time which sends radar detection finished
event to cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Head & Tail IEs are supposed to be added to beacon and probe response.
This patch adds separate function for parsing head and tail IEs from
cfg80211_beacon_data and sets them to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Refactor mwifiex_cfg80211_start_ap by creating separate function
to set AP channel and another for configuring other AP parameters
and starting AP.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Store AP configuration in private structure so that we know
current AP configuration.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, we support virtual interface type change from
station<=>adhoc or station <=> p2p client/GO.
This patch adds support to change virtual interface type to
any of the type advertised in interface combinations.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently interface limits are checked by seeing if bss_mode for
particular priv is set. If bss_mode is not set, interface creation
is allowed. This patch adds framework to initializes maximum virtual
interfaces supported during load time and check current number of
interfaces created agains allowed interface limit during new virtual
interface creation.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW initialization routine can also be called while changing
virtual interface types.
This patch adds bool parameter "init" to init command routine
so as to differentiate between initialization during driver load
and change virtual interface handler.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This would be used to set mac address while changing virtual
interface to different types.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wdev is used even after del_virtual_interface handler in cfg80211
in nl80211_post_doit. Since we have freed wdev in handling of
del_virtual_intf, this can result into crash while deleting
interface.
Avoid this be not declaring wdev which part of
mwifiex_private structure but struct wireless_dev type.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is not used anywhere execpt initialization.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If host fails to wakeup the firmware, we will trigger card reset
after 3 second timeout.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This flag is never set but checked at two places. We will get rid of
this code.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
