Since we added the dpaa2_switch_acl_entry_add() function in the previous
patches to hide all the details of actually adding the ACL entry by
issuing a firmware command, let's use it also for adding a CPU trap for
the STP frames.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support TC_SETUP_CLSMATCHALL by using the same ACL table entries
framework as for tc flower. Adding a matchall rule is done by installing
an entry which has a mask of all zeroes, thus matching on any packet.
This can be used as a catch-all type of rule if used correctly, ie the
priority of the matchall filter should be kept as the lowest one in the
entire filter block.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for tc flower hardware offload on the ingress
path. Shared filter blocks are supported by sharing a single ACL table
between multiple ports.
The following flow keys are supported:
- Ethernet: dst_mac/src_mac
- IPv4: dst_ip/src_ip/ip_proto/tos
- VLAN: vlan_id/vlan_prio/vlan_tpid/vlan_dei
- L4: dst_port/src_port
As per flow actions, the following are supported:
- drop
- mirred egress redirect
- trap
Each ACL entry (filter) can be setup with only one of the listed
actions.
A sorted single linked list is used to keep the ACL entries by their
order of priority. When adding a new filter, this enables us to quickly
ascertain if the new entry has the highest priority of the entire block
or if we should make some space in the ACL table by increasing the
priority of the filters already in the table.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new structure - dpaa2_switch_acl_tbl - to hold all data
related to an ACL table: number of rules added, ACL table id, etc.
This will be used more in the next patches when adding support for
sharing an ACL table between ports.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an ACL entry in each port's ACL table to redirect any frame that
has the destination MAC address equal to the STP dmac to the control
interface.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep track of the current learning state per port so that we can
reference it in the next patches when setting up a STP state.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to trap frames to the CPU, the DPAA2 switch uses the ACL table.
At probe time, create an ACL table for each switch port so that in the
next patches we can use this to trap STP frames and redirect them to the
control interface.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring per port unknown flooding by accepting both
BR_FLOOD and BR_MCAST_FLOOD as offloadable bridge port flags.
The DPAA2 switch does not support at the moment configuration of unknown
multicast flooding independently of unknown unicast flooding, therefore
check that both BR_FLOOD and BR_MCAST_FLOOD have the same state.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BR_BCAST_FLOOD bridge port flag is now accepted by the driver and a
change in its state will determine a reconfiguration of the broadcast
egress flooding list on the FDB associated with the port.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the dpaa2-switch driver has basic I/O capabilities on the
switch port net_devices and multiple bridging domains are supported,
move the driver out of staging.
The dpaa2-switch driver is placed right next to the dpaa2-eth driver
since, in the near future, they will be sharing most of the data path.
I didn't implement code reuse in this patch series because I wanted to
keep it as small as possible.
Also, the README is removed from staging with the intention to add
proper rst documentation afterwards to actually match was is supported
by the driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
