Need to wait for the last fence before unmapping. This
also fixes a memory leak in amdgpu_userqueue_cleanup()
when the fence isn't signalled.
Fixes: b0db33c8c5 ("drm/amdgpu/userq: rework front end call sequence")
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was missed when the map and unmap were split out
of the mqd create and destroy functions.
Fixes: b0db33c8c5 ("drm/amdgpu/userq: rework front end call sequence")
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Track the state of the queue rather than simple active vs
not. This is needed for other states (hung, preempted, etc.).
While we are at it, move the state tracking into the user
queue front end code.
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If user queues are disabled for all IPs in the case
of suspend and resume and for gfx/compute in the case
of enforce isolation, we can return early.
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
rn_vbios_smu_set_dprefclk() was added in 2019 by
commit 4edb6fc918 ("drm/amd/display: Add Renoir clock manager")
rv1_vbios_smu_set_dprefclk() was also added in 2019 by
commit dc88b4a684 ("drm/amd/display: make clk mgr soc specific")
neither have been used.
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
radeon_fence_wait_any() last use was removed in 2023's
commit 254986e324 ("drm/radeon: Use the drm suballocation manager
implementation.")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The last use of r600_hdmi_audio_workaround() was removed by 2014's
commit 6e72376dcc ("radeon/audio: consolidate audio_mode_set()
functions")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Print a kernel message when the scrub bit of status register is set to
indicate that errors are being logged by the scrub.
Signed-off-by: Xiang Liu <xiang.liu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since b255ce4388, it is possible that the CRTC timing
information for the preferred mode has not yet been
calculated while amdgpu_dm_connector_mode_valid() is running.
In this case use the CRTC timing information of the actual mode.
Fixes: b255ce4388 ("drm/amdgpu: don't change mode in amdgpu_dm_connector_mode_valid()")
Closes: https://lore.kernel.org/all/ed09edb167e74167a694f4854102a3de6d2f1433.camel@irl.hu/
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4085
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Reviewed-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The minimum value of the dst_y_prefetch_equ was not correct
in prefetch calculation whice causes OPTC underflow.
[How]
Add the min operation of dst_y_prefetch_equ in prefetch calculation
for legacy DML.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: TungYu Lu <tungyu.lu@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There are several gaps that can result in SubVP being enabled with
incompatible HW cursor sizes, and unjust restrictions to cursor size due
to wrong predictions on future usage of SubVP
[HOW]
- remove "prediction" logic in favor of tagging based on previous SubVP
usage
- block SubVP if current HW cursor settings are incompatible
- provide interface for DM to determine if HW cursor should be disabled
due to an attempt to enable SubVP
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a helper to get a mask of IPs which support user queues.
Use this in the INFO IOCTL to get the IP mask to replace
the current code.
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add queue id support to the user queue wait IOCTL
drm_amdgpu_userq_wait structure.
This is required to retrieve the wait user queue and maintain
the fence driver references in it so that the user queue in
the same context releases their reference to the fence drivers
at some point before queue destruction.
Otherwise, we would gather those references until we
don't have any more space left and crash.
v2: Modify the UAPI comment as per the mesa and libdrm UAPI comment.
Libdrm MR: https://gitlab.freedesktop.org/mesa/drm/-/merge_requests/408
Mesa MR: https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/34493
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So that we initialize the MQD as a secure queue.
Reviewed-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Jesse.Zhang <Jesse.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Pixel rate dividor was not programmed correctly for 1 pixel per cycle
configuration for empty tu case.
[How]
Included check for empty tu when pixel rate dividor values were selected.
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Recent findings show negligible power savings between IPS2 and RCG
during static desktop. In fact, DCN related clocks are higher
when IPS2 is enabled vs RCG.
RCG_IN_ACTIVE is also the default policy for another OS supported by
DC, and it has faster entry/exit.
[How]
Remove previous logic that checked for IPS2 support, and just default
to `DMUB_IPS_RCG_IN_ACTIVE_IPS2_IN_OFF`.
Fixes: 199888aa25 ("drm/amd/display: Update IPS default mode for DCN35/DCN351")
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
not all the asic using the same code path.
need to revisit and limit the impact.
This reverts commit 32be4e39f4.
Reviewed-by: Gabe Teeger <gabe.teeger@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
LTTPR are required to program DPCD 0000Eh to 0x4 (16ms) upon AUX read
reply to this register. Since old Sinks witih DPCD rev 1.1 and earlier
may not support this register, assume the mandatory value is programmed
by the LTTPR to avoid AUX timeout issues.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The ACPI EDID in the BIOS of a Lenovo laptop includes 3 blocks, but
dm_helpers_probe_acpi_edid() has a start that is 'char'. The 3rd
block index starts after 255, so it can't be indexed properly.
This leads to problems with the display when the EDID is parsed.
[How]
Change the variable type to 'short' so that larger values can be indexed.
Cc: Renjith Pananchikkal <renjith.pananchikkal@amd.com>
Reported-by: Mark Pearson <mpearson@lenovo.com>
Suggested-by: David Ober <dober@lenovo.com>
Fixes: c6a837088b ("drm/amd/display: Fetch the EDID from _DDC if available for eDP")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With the PCH macros switched to use struct intel_display, we have a
number of files that no longer need struct drm_i915_private or anything
else from i915_drv.h anymore. Remove the #include, and add the missing
includes that were previously implicit.
v2: Drop even more of the includes
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Link: https://lore.kernel.org/r/5dc9e6a98461c344febac4c645875d8688eba906.1744880985.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that INTEL_PCH_TYPE() and HAS_PCH_*() macros are under display, and
accept a struct intel_display pointer, use that instead of struct
drm_i915_private pointer in display code.
This is done naively by running:
$ sed -i 's/\(INTEL_PCH_TYPE\|HAS_PCH_[A-Z0-9_-]*\)([^)]*)/\1(display)/g' \
$(find drivers/gpu/drm/i915/display -name "*.c")
and fixing the fallout, i.e. removing unused local i915 variables and
adding display variables where needed.
v2: Rebase
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Link: https://lore.kernel.org/r/999f4d7b8ed11739b1c5ec8d6408fc39d5e3776b.1744880985.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
With lan88xx based devices the lan78xx driver can get stuck in an
interrupt loop while bringing the device up, flooding the kernel log
with messages like the following:
lan78xx 2-3:1.0 enp1s0u3: kevent 4 may have been dropped
Removing interrupt support from the lan88xx PHY driver forces the
driver to use polling instead, which avoids the problem.
The issue has been observed with Raspberry Pi devices at least since
4.14 (see [1], bug report for their downstream kernel), as well as
with Nvidia devices [2] in 2020, where disabling interrupts was the
vendor-suggested workaround (together with the claim that phylib
changes in 4.9 made the interrupt handling in lan78xx incompatible).
Iperf reports well over 900Mbits/sec per direction with client in
--dualtest mode, so there does not seem to be a significant impact on
throughput (lan88xx device connected via switch to the peer).
[1] https://github.com/raspberrypi/linux/issues/2447
[2] https://forums.developer.nvidia.com/t/jetson-xavier-and-lan7800-problem/142134/11
Link: https://lore.kernel.org/0901d90d-3f20-4a10-b680-9c978e04ddda@lunn.ch
Fixes: 792aec47d5 ("add microchip LAN88xx phy driver")
Signed-off-by: Fiona Klute <fiona.klute@gmx.de>
Cc: kernel-list@raspberrypi.com
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250416102413.30654-1-fiona.klute@gmx.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Right now the DRM_PANTHOR_BO_NO_MMAP flag is ignored by
panthor_ioctl_bo_mmap_offset(), meaning BOs with this flag set can
have a file offset but can't be mapped anyway, because
panthor_gem_mmap() will filter them out.
If we error out at mmap_offset creation time, we can get rid of
panthor_gem_mmap() and call drm_gem_shmem_object_mmap directly, and
we get rid of this inconsistency of having an mmap offset for a
BO that can never be mmap-ed.
Changes in v2:
- Get rid of panthor_gem_mmap()
- Get rid of the Fixes tag and adjust the commit message accordingly
- Return ENOPERM instead of EINVAL
Changes in v3:
- Don't leak the BO ref
- Add R-bs
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Link: https://lore.kernel.org/r/20250417121942.3574111-1-boris.brezillon@collabora.com
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
On x86_64 with gcc version 13.3.0, I compile kernel with:
make defconfig
./scripts/kconfig/merge_config.sh .config <(
echo CONFIG_COMPILE_TEST=y
)
make KCFLAGS="-fno-inline-functions -fno-inline-small-functions -fno-inline-functions-called-once"
Then I get a linker error:
ld: vmlinux.o: in function `pxp_fw_dependencies_completed':
kintel_pxp.c:(.text+0x95728f): undefined reference to `intel_pxp_gsccs_is_ready_for_sessions'
This is caused by not having a intel_pxp_gsccs_is_ready_for_sessions()
header stub for CONFIG_DRM_I915_PXP=n. Add it.
Signed-off-by: Chen Linxuan <chenlinxuan@uniontech.com>
Fixes: 99afb7cc8c ("drm/i915/pxp: Add ARB session creation and cleanup")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20250415090616.2649889-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit b484c1e225)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When trying to enable a port that has no transport configured yet,
nvmet_enable_port() uses NVMF_TRTYPE_MAX (255) to query the transports
array, causing an out-of-bounds access:
[ 106.058694] BUG: KASAN: global-out-of-bounds in nvmet_enable_port+0x42/0x1da
[ 106.058719] Read of size 8 at addr ffffffff89dafa58 by task ln/632
[...]
[ 106.076026] nvmet: transport type 255 not supported
Since commit 200adac758, NVMF_TRTYPE_MAX is the default state as configured by
nvmet_ports_make().
Avoid this by checking for NVMF_TRTYPE_MAX before proceeding.
Fixes: 200adac758 ("nvme: Add PCI transport type")
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
commit a8972d5a49 ("drm: panel: jd9365da-h3: fix reset signal polarity")
fixed reset signal polarity in jadard_dsi_probe() and jadard_prepare().
It was not done in jadard_unprepare() because of an incorrect assumption
about reset line handling in power off mode. After looking into the
datasheet, it now appears that before disabling regulators, the reset line
is deasserted first, and if reset_before_power_off_vcioo is true, then the
reset line is asserted.
Fix reset polarity by inverting gpiod_set_value() second argument in
in jadard_unprepare().
Fixes: 6b818c533d ("drm: panel: Add Jadard JD9365DA-H3 DSI panel")
Fixes: 2b976ad760 ("drm/panel: jd9365da: Support for kd101ne3-40ti MIPI-DSI panel")
Fixes: a8972d5a49 ("drm: panel: jd9365da-h3: fix reset signal polarity")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250417195507.778731-1-hugo@hugovil.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250417195507.778731-1-hugo@hugovil.com
We never properly supported this panel and always used the wrong init
sequence. Drop support so we can move it to it's own proper driver.
Fixes: 5933baa36e ("drm/panel/samsung-sofef00: Add panel for OnePlus 6/T devices")
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250419-drop-s6e3fc2x01-support-v1-1-05edfe0d27aa@ixit.cz
Christian reports that 4K output using YUV420 encoding fails with the
following error:
Fatal Error, invalid HDMI vclk freq 593406
Modetest shows the following:
3840x2160 59.94 3840 4016 4104 4400 2160 2168 2178 2250 593407 flags: xxxx, xxxx,
drm calculated value -------------------------------------^
This indicates that there's a (1kHz) mismatch between the clock
calculated by the drm framework and the meson driver.
Relevant function call stack:
(drm framework)
-> meson_encoder_hdmi_atomic_enable()
-> meson_encoder_hdmi_set_vclk()
-> meson_vclk_setup()
The video clock requested by the drm framework is 593407kHz. This is
passed by meson_encoder_hdmi_atomic_enable() to
meson_encoder_hdmi_set_vclk() and the following formula is applied:
- the frequency is halved (which would be 296703.5kHz) and rounded down
to the next full integer, which is 296703kHz
- TMDS clock is calculated (296703kHz * 10)
- video encoder clock is calculated - this needs to match a table from
meson_vclk.c and so it doubles the previously halved value again
(resulting in 593406kHz)
- meson_vclk_setup() can't find (either directly, or by deriving it from
594000kHz * 1000 / 1001 and rounding to the closest integer value -
which is 593407kHz as originally requested by the drm framework) a
matching clock in it's internal table and errors out with "invalid
HDMI vclk freq"
Fix the division precision by switching the whole meson driver to use
unsigned long long (64-bit) Hz values for clock frequencies instead of
unsigned int (32-bit) kHz to fix the rouding error.
Fixes: e5fab2ec9c ("drm/meson: vclk: add support for YUV420 setup")
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250421201300.778955-3-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250421201300.778955-3-martin.blumenstingl@googlemail.com
With ATA devices supporting the CDL feature, using CDL requires that the
feature be enabled with a SET FEATURES command. This command is issued
as the translated command for the MODE SELECT command issued by
scsi_cdl_enable() when the user enables CDL through the device
cdl_enable sysfs attribute.
However, the implementation of scsi_cdl_enable() always issues a MODE
SELECT command for ATA devices when the enable argument is true, even if
CDL is already enabled on the device. While this does not cause any
issue with using CDL descriptors with read/write commands (the CDL
feature will be enabled on the drive), issuing the MODE SELECT command
even when the device CDL feature is already enabled will cause a reset
of the ATA device CDL statistics log page (as defined in ACS, any CDL
enable action must reset the device statistics).
Avoid this needless actions (and the implied statistics log page reset)
by modifying scsi_cdl_enable() to issue the MODE SELECT command to
enable CDL if and only if CDL is not reported as already enabled on the
device.
And while at it, simplify the initialization of the is_ata boolean
variable and move the declaration of the scsi mode data and sense header
variables to within the scope of ATA device handling.
Fixes: 1b22cfb141 ("scsi: core: Allow enabling and disabling command duration limits")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
With ATA devices supporting the CDL feature, using CDL requires that the
feature be enabled with a SET FEATURES command. This command is issued
as the translated command for the MODE SELECT command issued by
scsi_cdl_enable() when the user enables CDL through the device
cdl_enable sysfs attribute.
Currently, ata_mselect_control_ata_feature() always translates a MODE
SELECT command for the ATA features subpage of the control mode page to
a SET FEATURES command to enable or disable CDL based on the cdl_ctrl
field. However, there is no need to issue the SET FEATURES command if:
1) The MODE SELECT command requests disabling CDL and CDL is already
disabled.
2) The MODE SELECT command requests enabling CDL and CDL is already
enabled.
Fix ata_mselect_control_ata_feature() to issue the SET FEATURES command
only when necessary. Since enabling CDL also implies a reset of the CDL
statistics log page, avoiding useless CDL enable operations also avoids
clearing the CDL statistics log.
Also add debug messages to clearly signal when CDL is being enabled or
disabled using a SET FEATURES command.
Fixes: df60f9c645 ("scsi: ata: libata: Add ATA feature control sub-page translation")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
For the ATA features subpage of the control mode page, the T10 SAT-6
specifications state that:
For a MODE SENSE command, the SATL shall return the CDL_CTRL field value
that was last set by an application client.
However, the function ata_msense_control_ata_feature() always sets the
CDL_CTRL field to the 0x02 value to indicate support for the CDL T2A and
T2B pages. This is thus incorrect and the value 0x02 must be reported
only after the user enables the CDL feature, which is indicated with the
ATA_DFLAG_CDL_ENABLED device flag. When this flag is not set, the
CDL_CTRL field of the ATA feature subpage of the control mode page must
report a value of 0x00.
Fix ata_msense_control_ata_feature() to report the correct values for
the CDL_CTRL field, according to the enable/disable state of the device
CDL feature.
Fixes: df60f9c645 ("scsi: ata: libata: Add ATA feature control sub-page translation")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
The function ata_mselect_control_ata_feature() has a return type defined
as unsigned int but this function may return negative error codes, which
are correctly propagated up the call chain as integers.
Fix ata_mselect_control_ata_feature() to have the correct int return
type.
While at it, also fix a typo in this function description comment.
Fixes: df60f9c645 ("scsi: ata: libata: Add ATA feature control sub-page translation")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
- Use kvzalloc() so that large exit_dump buffer allocations don't fail
easily.
- Remove cpu.weight / cpu.idle unimplemented warnings which are more
annoying than helpful. This makes SCX_OPS_HAS_CGROUP_WEIGHT unnecessary.
Mark it for deprecation.
-----BEGIN PGP SIGNATURE-----
iIQEABYKACwWIQTfIjM1kS57o3GsC/uxYfJx3gVYGQUCaAaeKw4cdGpAa2VybmVs
Lm9yZwAKCRCxYfJx3gVYGcDjAQDM14FReObIKOOuqzlNaYXQqcSW2///ZVf/FR8j
HpWtyAD/Tsqg6CzBpTxKkpMRLsE2iKI1t770vkUnDbjcnR0Rxgc=
=rIV5
-----END PGP SIGNATURE-----
Merge tag 'sched_ext-for-6.15-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext
Pull sched_ext fixes from Tejun Heo:
- Use kvzalloc() so that large exit_dump buffer allocations don't fail
easily
- Remove cpu.weight / cpu.idle unimplemented warnings which are more
annoying than helpful.
This makes SCX_OPS_HAS_CGROUP_WEIGHT unnecessary. Mark it for
deprecation
* tag 'sched_ext-for-6.15-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext:
sched_ext: Mark SCX_OPS_HAS_CGROUP_WEIGHT for deprecation
sched_ext: Remove cpu.weight / cpu.idle unimplemented warnings
sched_ext: Use kvzalloc for large exit_dump allocation
- Fix compilation in CONFIG_LOCKDEP && !CONFIG_PROVE_RCU configurations.
- Allow "cpuset_v2_mode" mount option for "cpuset" filesystem type to make
life easier for android.
-----BEGIN PGP SIGNATURE-----
iIQEABYKACwWIQTfIjM1kS57o3GsC/uxYfJx3gVYGQUCaAac+Q4cdGpAa2VybmVs
Lm9yZwAKCRCxYfJx3gVYGUiAAQCbw6eOFAE+sjI6GgAeMVORbLqyufGDNPvBwgzJ
xPxgcwD/ZLlsJWRG6BzQ/KHeFZnGWSJEiqSSFHGCCr0l4QkIdgA=
=ay1E
-----END PGP SIGNATURE-----
Merge tag 'cgroup-for-6.15-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
- Fix compilation in CONFIG_LOCKDEP && !CONFIG_PROVE_RCU configurations
- Allow "cpuset_v2_mode" mount option for "cpuset" filesystem type to
make life easier for android
* tag 'cgroup-for-6.15-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup/cpuset-v1: Add missing support for cpuset_v2_mode
cgroup: Fix compilation issue due to cgroup_mutex not being exported
Vladimir Oltean says:
====================
ENETC bug fixes for bpf_xdp_adjust_head() and bpf_xdp_adjust_tail()
It has been reported that on the ENETC driver, bpf_xdp_adjust_head()
and bpf_xdp_adjust_tail() are broken in combination with the XDP_PASS
verdict. I have constructed a series a simple XDP programs and tested
with various packet sizes and confirmed that this is the case.
Patch 3/3 fixes the core issue, which is that the sk_buff created on
XDP_PASS is created by the driver as if XDP never ran, but in fact the
geometry needs to be adjusted according to the delta applied by the
program on the original xdp_buff. It depends on commit 539c1fba1a
("xdp: add generic xdp_build_skb_from_buff()") which is not available in
"stable" but perhaps should be.
Patch 2/3 is a small refactor necessary for 3/3.
Patch 1/3 fixes a related issue I noticed, which is that
bpf_xdp_adjust_tail() with a positive offset works for linear XDP
buffers, but returns an error for non-linear ones, even if there is
plenty of space in the final page fragment.
====================
Link: https://patch.msgid.link/20250417120005.3288549-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vlatko Markovikj reported that XDP programs attached to ENETC do not
work well if they use bpf_xdp_adjust_head() or bpf_xdp_adjust_tail(),
combined with the XDP_PASS verdict. A typical use case is to add or
remove a VLAN tag.
The resulting sk_buff passed to the stack is corrupted, because the
algorithm used by the driver for XDP_PASS is to unwind the current
buffer pointer in the RX ring and to re-process the current frame with
enetc_build_skb() as if XDP hadn't run. That is incorrect because XDP
may have modified the geometry of the buffer, which we then are
completely unaware of. We are looking at a modified buffer with the
original geometry.
The initial reaction, both from me and from Vlatko, was to shop around
the kernel for code to steal that would calculate a delta between the
old and the new XDP buffer geometry, and apply that to the sk_buff too.
We noticed that veth and generic xdp have such code.
The headroom adjustment is pretty uncontroversial, but what turned out
severely problematic is the tailroom.
veth has this snippet:
__skb_put(skb, off); /* positive on grow, negative on shrink */
which on first sight looks decent enough, except __skb_put() takes an
"unsigned int" for the second argument, and the arithmetic seems to only
work correctly by coincidence. Second issue, __skb_put() contains a
SKB_LINEAR_ASSERT(). It's not a great pattern to make more widespread.
The skb may still be nonlinear at that point - it only becomes linear
later when resetting skb->data_len to zero.
To avoid the above, bpf_prog_run_generic_xdp() does this instead:
skb_set_tail_pointer(skb, xdp->data_end - xdp->data);
skb->len += off; /* positive on grow, negative on shrink */
which is more open-coded, uses lower-level functions and is in general a
bit too much to spread around in driver code.
Then there is the snippet:
if (xdp_buff_has_frags(xdp))
skb->data_len = skb_shinfo(skb)->xdp_frags_size;
else
skb->data_len = 0;
One would have expected __pskb_trim() to be the function of choice for
this task. But it's not used in veth/xdpgeneric because the extraneous
fragments were _already_ freed by bpf_xdp_adjust_tail() ->
bpf_xdp_frags_shrink_tail() -> ... -> __xdp_return() - the backing
memory for the skb frags and the xdp frags is the same, but they don't
keep individual references.
In fact, that is the biggest reason why this snippet cannot be reused
as-is, because ENETC temporarily constructs an skb with the original len
and the original number of frags. Because the extraneous frags are
already freed by bpf_xdp_adjust_tail() and returned to the page
allocator, it means the entire approach of using enetc_build_skb() is
questionable for XDP_PASS. To avoid that, one would need to elevate the
page refcount of all frags before calling bpf_prog_run_xdp() and drop it
after XDP_PASS.
There are other things that are missing in ENETC's handling of XDP_PASS,
like for example updating skb_shinfo(skb)->meta_len.
These are all handled correctly and cleanly in commit 539c1fba1a
("xdp: add generic xdp_build_skb_from_buff()"), added to net-next in
Dec 2024, and in addition might even be quicker that way. I have a very
strong preference towards backporting that commit for "stable", and that
is what is used to fix the handling bugs. It is way too messy to go
this deep into the guts of an sk_buff from the code of a device driver.
Fixes: d1b15102dd ("net: enetc: add support for XDP_DROP and XDP_PASS")
Reported-by: Vlatko Markovikj <vlatko.markovikj@etas.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20250417120005.3288549-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This small snippet of code ensures that we do something with the array
of RX software buffer descriptor elements after passing the skb to the
stack. In this case, we see if the other half of the page is reusable,
and if so, we "turn around" the buffers, making them directly usable by
enetc_refill_rx_ring() without going to enetc_new_page().
We will need to perform this kind of buffer flipping from a new code
path, i.e. from XDP_PASS. Currently, enetc_build_skb() does it there
buffer by buffer, but in a subsequent change we will stop using
enetc_build_skb() for XDP_PASS.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20250417120005.3288549-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At the time when bpf_xdp_adjust_tail() gained support for non-linear
buffers, ENETC was already generating this kind of geometry on RX, due
to its use of 2K half page buffers. Frames larger than 1472 bytes
(without FCS) are stored as multi-buffer, presenting a need for multi
buffer support to work properly even in standard MTU circumstances.
Allow bpf_xdp_frags_increase_tail() to know the allocation size of paged
data, so it can safely permit growing the tailroom of the buffer from
XDP programs.
Fixes: bf25146a55 ("bpf: add frags support to the bpf_xdp_adjust_tail() API")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20250417120005.3288549-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function xdp_convert_buff_to_frame() may return NULL if it fails
to correctly convert the XDP buffer into an XDP frame due to memory
constraints, internal errors, or invalid data. Failing to check for NULL
may lead to a NULL pointer dereference if the result is used later in
processing, potentially causing crashes, data corruption, or undefined
behavior.
On XDP redirect failure, the associated page must be released explicitly
if it was previously retained via get_page(). Failing to do so may result
in a memory leak, as the pages reference count is not decremented.
Cc: stable@vger.kernel.org # v5.9+
Fixes: 6c5aa6fc4d ("xen networking: add basic XDP support for xen-netfront")
Signed-off-by: Alexey Nepomnyashih <sdl@nppct.ru>
Link: https://patch.msgid.link/20250417122118.1009824-1-sdl@nppct.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simon Horman says:
====================
MAINTAINERS: Update entries for s390 network driver files
Update the entries for s390 network driver files to:
* Add include/linux/ism.h to MAINTAINERS
* Add s390 network driver files to the NETWORKING DRIVERS section
This is to aid developers, and tooling such as get_maintainer.pl alike
to CC patches to all the appropriate people and mailing lists. And is
in keeping with an ongoing effort for NETWORKING entries in MAINTAINERS
to more accurately reflect the way code is maintained.
====================
Link: https://patch.msgid.link/20250417-ism-maint-v1-0-b001be8545ce@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These files are already correctly covered by the S390 NETWORKING DRIVERS
section. In practice commits for these drivers feed into the Networking
subsystem. So it seems appropriate to also list them under NETWORKING
DRIVERS.
This aids developers, and tooling such as get_maintainer.pl
alike to CC patches to all the appropriate people and mailing lists.
And is in keeping with an ongoing effort for NETWORKING entries
in MAINTAINERS to more accurately reflect the way code is maintained.
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250417-ism-maint-v1-2-b001be8545ce@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ism.h appears to be part of s390 networking drivers
so add it to the corresponding section in MAINTAINERS.
This aids developers, and tooling such as get_maintainer.pl
alike to CC patches to the appropriate people and mailing lists.
And is in keeping with an ongoing effort for NETWORKING entries
in MAINTAINERS to more accurately reflect the way code is maintained.
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250417-ism-maint-v1-1-b001be8545ce@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensure event logs are only generated when the debug logging level
MPI3_DEBUG_EVENT is enabled. This prevents unnecessary logging.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20250415101546.204018-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
