This allows low level drivers to refresh the tx agg session timer, based on
querying stats from the firmware usually. Especially for some mt76 devices
support .net_fill_forward_path would bypass mac80211, which leads to tx BA
session timeout clients that set a timeout in their AddBA response to our
request, even if our request is without a timeout.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://lore.kernel.org/r/7c3f72eac1c34921cd84a462e60d71e125862152.1676616450.git.ryder.lee@mediatek.com
[slightly clarify commit message, add note about RCU]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new TLV format enables adding TLVs after the fixed
fields in radiotap, as part of the radiotap header.
Support this and move vendor data to the TLV format,
allowing a reuse of the RX_FLAG_RADIOTAP_VENDOR_DATA as
the new RX_FLAG_RADIOTAP_TLV_AT_END flag.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.b18fd5da8477.I576400ec40a7b35ef97a3b09a99b3a49e9174786@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds the infrastructure to have netdev specific per-link data both
for mac80211 and the driver in debugfs. For the driver, a new callback
is added which is only used if MLO is supported.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.fb4c947e4df8.I69b3516ddf4c8a7501b395f652d6063444ecad63@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While often not needed, this considerably simplifies going from a link
specific bss_config to the vif. This helps with e.g. creating link
specific debugfs entries inside drivers.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.46f701a10ed5.I20390b2a8165ff222d66585915689206ea93222b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- Configure the bitmap in link_conf and notify the driver.
- Modify 'change' in ieee80211_start_ap() from u32 to u64 to support
BSS_CHANGED_EHT_PUNCTURING.
- Propagate the bitmap in channel switch events to userspace.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Link: https://lore.kernel.org/r/20230131001227.25014-5-quic_alokad@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Handle the Puncturing info received from the AP in the
EHT Operation element in beacons.
If the info is invalid:
- during association: disable EHT connection for the AP
- after association: disconnect
This commit includes many (internal) bugfixes and spec
updates various people.
Co-developed-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://lore.kernel.org/r/20230127123930.4fbc74582331.I3547481d49f958389f59dfeba3fcc75e72b0aa6e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Somehow an extra 'e' slipped in there without anyone noticing,
drop that from ieeee80211_obss_color_collision_notify().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Looks like this is required, even if all of the members
are separately described. Add a line to avoid the warning.
Fixes: f66c48af7a ("mac80211: support minimal EHT rate reporting on RX")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add minimal support for RX EHT rate reporting, not yet
adding (modifying) any radiotap headers, just statistics
for cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding flags for SU Beamformer, SU Beamformee, MU Beamformer and Full
Bandwidth UL MU-MIMO for HE. This is utilized to pass MU-MIMO
configurations from user space to driver in AP mode.
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Link: https://lore.kernel.org/r/1665006886-23874-2-git-send-email-quic_msinada@quicinc.com
[fixed indentation, removed redundant !!]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding flags for SU Beamformer, SU Beamformee, MU Beamformer and
MU Beamformee for VHT. This is utilized to pass MU-MIMO
configurations from user space to driver in AP mode.
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Link: https://lore.kernel.org/r/1665006886-23874-1-git-send-email-quic_msinada@quicinc.com
[fixed indentation, removed redundant !!]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the two cherry picked commits from wireless to wireless-next we have
several conflicts in mt76. To avoid any bugs with conflicts merge wireless into
wireless-next.
96f134dc19 wifi: mt76: handle possible mt76_rx_token_consume failures
fe13dad899 wifi: mt76: dma: do not increment queue head if mt76_dma_add_buf fails
This reverts commit acb99b9b2a ("mac80211: Add stations iterator
where the iterator function may sleep"). A different approach was found
for the rtw88 driver where most of the problematic locks were converted
to a driver-local mutex. Drop ieee80211_iterate_stations() because there
are no users of that function.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221226191609.2934234-1-martin.blumenstingl@googlemail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a running wake_tx_queue() call is aborted due to a hw queue stop
the corresponding iTXQ is not always correctly marked for resumption:
wake_tx_push_queue() can stops the queue run without setting
@IEEE80211_TXQ_STOP_NETIF_TX.
Without the @IEEE80211_TXQ_STOP_NETIF_TX flag __ieee80211_wake_txqs()
will not schedule a new queue run and remaining frames in the queue get
stuck till another frame is queued to it.
Fix the issue for all drivers - also the ones with custom wake_tx_queue
callbacks - by moving the logic into ieee80211_tx_dequeue() and drop the
redundant @txqs_stopped.
@IEEE80211_TXQ_STOP_NETIF_TX is also renamed to @IEEE80211_TXQ_DIRTY to
better describe the flag.
Fixes: c850e31f79 ("wifi: mac80211: add internal handler for wake_tx_queue")
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20221230121850.218810-1-alexander@wetzel-home.de
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be used to selectively disable feature flags for checksum offload,
scatter/gather or GSO by changing vif->netdev_features.
Removing features from vif->netdev_features does not affect the netdev
features themselves, but instead fixes up skbs in the tx path so that the
offloads are not needed in the driver.
Aside from making it easier to deal with vif type based hardware limitations,
this also makes it possible to optimize performance on hardware without native
GSO support by declaring GSO support in hw->netdev_features and removing it
from vif->netdev_features. This allows mac80211 to handle GSO segmentation
after the sta lookup, but before itxq enqueue, thus reducing the number of
unnecessary sta lookups, as well as some other per-packet processing.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20221010094338.78070-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Start to align the TX handling to only use internal TX queues (iTXQs):
Provide a handler for drivers not having a custom wake_tx_queue
callback and update the documentation.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We might sometimes need to use RCU and locking in the same code
path, so add the two variants link_conf_dereference_check() and
link_sta_dereference_check().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Create debugfs data per-link. For drivers, there is a new operation
link_sta_add_debugfs which will always be called.
For non-MLO, the station directory will be used directly rather than
creating a corresponding subdirectory. As such, non-MLO drivers can
simply continue to create the data from sta_debugfs_add.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
[add missing inlines if !CONFIG_MAC80211_DEBUGFS]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While often not needed, this considerably simplifies going from a link
to the STA. This helps in cases such as debugfs where a single pointer
should allow accessing a specific link and the STA.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement an API function and debugfs file to switch
active links.
Also provide an async version of the API so drivers
can call it in arbitrary contexts, e.g. while in the
authorized callback.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The A-MSDU data needs to be stored per-link and aggregated into a single
value for the station. Add a new struct ieee_80211_sta_aggregates in
order to store this data and a new function
ieee80211_sta_recalc_aggregates to update the current data for the STA.
Note that in the non MLO case the pointer in ieee80211_sta will directly
reference the data in deflink.agg, which means that recalculation may be
skipped in that case.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add macros (and an exported function) to allow checking some
link RCU protected accesses that are happening in callbacks
from mac80211 and are thus under the correct lock.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a link_id parameter to ieee80211_nullfunc_get() to be
able to obtain a correctly addressed frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new API function ieee80211_find_sta_by_link_addrs()
that looks up the STA and link ID based on interface and
station link addresses.
We're going to use it for mac80211-hwsim to track on the
AP side which links are active.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to let the driver select active links and properly
make multi-link connections, as a first step isolate the
driver from inactive links, and set the active links to be
only the association link for client-side interfaces. For
AP side nothing changes since APs always have to have all
their links active.
To simplify things, update the for_each_sta_active_link()
API to include the appropriate vif pointer.
This also implies not allocating a chanctx for an inactive
link, which requires a few more changes.
Since we now no longer try to program multiple links to the
driver, remove the check in the MLME code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The SMPS power save mode needs to be per-link rather than being shared
for all links. As such, move it into struct ieee80211_link_sta.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To helper drivers if they e.g. have a lookup of the link_sta
pointer, add the link ID to the link_sta structure.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO, when the address translation from link to MLD is done
in fw/hw, it is necessary to be able to have some information
on the link on which the frame has been received. Extend the
rx API to include link_id and a valid flag in ieee80211_rx_status.
Also make chanes to mac80211 rx APIs to make use of the reported
link_id after sanity checks.
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Link: https://lore.kernel.org/r/20220817104213.2531-2-quic_vthiagar@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement key installation and lookup (on TX and RX)
for MLO, so we can use multiple GTKs/IGTKs/BIGTKs.
Co-authored-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a preliminary version which will be updated later
to loop over vif's and sta's active links.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For drivers using software encryption for multicast TX, such
as mac80211_hwsim, mac80211 needs to duplicate the multicast
frames on each link, if MLO is enabled. Do this, but don't
just make it dependent on the key but provide a separate flag
for drivers to opt out of this.
This is not very efficient, I expect that drivers will do it
in firmware/hardware or at least with DMA engine assistence,
so this is mostly for hwsim.
To make this work, also implement the SNS11 sequence number
space that an AP MLD shall have, and modify the API to the
__ieee80211_subif_start_xmit() function to always require the
link ID bits to be set.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a couple of new things that should be possible
with MLO:
* selecting the link to transmit to a station by link ID,
which a previous patch added to the nl80211 API
* selecting the link by frequency, similarly
* allowing transmittion to an MLD without specifying any
channel or link ID, with MLD addresses
Enable these use cases. Also fix the address comparison
in client mode to use the AP (MLD) address.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the low level driver reports hardware timestamps for frame
TX status or frame RX, pass the timestamps to cfg80211.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an MLO AP is transmitting to a non-MLO station, addr2 should be set
to a link address. This should be done before the frame is encrypted as
otherwise aad verification would fail. In case of software encryption
this can't be left for the device to handle, and should be done by
mac80211 when building the frame hdr.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since struct ieee80211_bss_conf already contains link_id,
passing link_id is not necessary.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since mac80211 already has a protected pointer to link_conf,
pass it to the driver to avoid additional RCU locking.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When calling start/stop_ap(), mac80211 already has a protected
link_conf pointer. Pass it to the driver, so it shouldn't
handle RCU protection.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To prepare a bit more for MLO in the client code,
track the AP's address (for now only the BSSID, but
will track the AP MLD's address later) separately
from the per-link BSSID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This really shouldn't be in a per-link config, we don't want
to let anyone control it that way (if anything, link powersave
could be forced through APIs to activate/deactivate a link),
and we don't support powersave in software with devices that
can do MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It might be useful to drivers to be able to pass only the
link_conf pointer, rather than both the pointer and the
link_id; add the link_id to the link_conf to facility that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since links can be added and removed dynamically, we need to
somehow protect the sdata->link[] and vif->link_conf[] array
pointers from disappearing when accessing them without locks.
RCU-ify the pointers to achieve this, which requires quite a
bit of rework.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commits 6a789ba679 and
2433647bc8.
The virtual time scheduler code has a number of issues:
- queues slowed down by hardware/firmware powersave handling were not properly
handled.
- on ath10k in push-pull mode, tx queues that the driver tries to pull from
were starved, causing excessive latency
- delay between tx enqueue and reported airtime use were causing excessively
bursty tx behavior
The bursty behavior may also be present on the round-robin scheduler, but there
it is much easier to fix without introducing additional regressions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Somehow kernel-doc complains here about strong markup, but
we really don't need the [] so just remove that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The lack of the colon makes it not parse the function parameter:
include/net/mac80211.h:6250: warning: Function parameter or member 'vif' not described in 'ieee80211_channel_switch_disconnect'
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Link: https://lore.kernel.org/r/11c1bdb861d89c93058fcfe312749b482851cbdb.1656409369.git.mchehab@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce the capability to specify gfp_t parameter to
ieeee80211_obss_color_collision_notify routine since it runs in
interrupt context in ieee80211_rx_check_bss_color_collision().
Fixes: 6d945a33f2 ("mac80211: introduce BSS color collision detection")
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/02c990fb3fbd929c8548a656477d20d6c0427a13.1655419135.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to be able to access these in a race-free way under
traffic while adding/removing them, so RCU-ify the pointers.
This requires passing a link_sta to a lot of functions so
we don't have to do the RCU handling everywhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the link id through to the get_beacon and return
the beacon for a specific link id.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In start_ap and stop_ap mac80211 callbacks pass the link_id
to the drivers.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the necessary infrastructure, including a new driver
method, to add/remove links to/from a station. To do this,
refactor the link alloc/free a bit, splitting that so we
can do it without linking them, to handle failures better.
Note that a station entry must be created representing an
MLD or a non-MLD STA, it cannot change between the two.
When representing an MLD, the 'deflink' is used for the
first link, which might be removed later, in which case
the memory isn't reused.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Take a few bits out of the control.flags to add the link ID
to TX frame metadata, so drivers don't need to look it up
by the address themselves. Implement that lookup where it's
needed, for internal frame TX, and set it to "unspecified"
for data transmissions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the interface is an MLD, then we don't know which band
the frame will be transmitted on, and we don't know how to
look up the band. Set the band information to zero in that
case, the driver cannot rely on it anyway.
No longer inline ieee80211_tx_skb_tid() since it's even
bigger now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the necessary infrastructure, including a new driver
method, to add/remove links to/from an interface.
Also add the missing link address to bss_conf (which we
use as link_conf too), and fill it, in station mode for
now just randomly, in AP mode we get the address from
cfg80211 since the link must be created with an address
first.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Start making some SMPS related code MLD-aware. This isn't
really done yet, but again cuts down our 'deflink' reliance.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove MAX_STA_LINKS and use IEEE80211_MLD_MAX_NUM_LINKS
instead to unify between the station and other data structures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the channel context code MLO aware, along with some
functions that it uses, so that the chan.c file is now
MLD-clean and no longer uses deflink/bss_conf/etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add pointers so we can start using link_id throughout the
code, even if for now only link ID 0 is valid, pointing
to the "built-in" bss_conf, which is used by drivers that
are not aware of MLD.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To add MLD, reuse the bss_conf structure later for per-link
information, so move some things into it that are per link.
Most transformations were done with the following spatch:
@@
expression sdata;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-sdata->vif.var
+sdata->vif.bss_conf.var
@@
struct ieee80211_vif *vif;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-vif->var
+vif->bss_conf.var
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only driver using this was iwlwifi, where we just removed
the support because it was never really used. Remove the code
from mac80211 as well.
Change-Id: I1667417a5932315ee9d81f5c233c56a354923f09
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds the new struct ieee80211_rate_status and replaces
'struct rate_info *rate' in ieee80211_tx_status with pointer and length
annotation.
The struct ieee80211_rate_status allows to:
(1) receive tx power status feedback for transmit power control (TPC)
per packet or packet retry
(2) dynamic mapping of wifi chip specific multi-rate retry (mrr)
chains with different lengths
(3) increase the limit of annotatable rate indices to support
IEEE802.11ac rate sets and beyond
ieee80211_tx_info, control and status buffer, and ieee80211_tx_rate
cannot be used to achieve these goals due to fixed size limitations.
Our new struct contains a struct rate_info to annotate the rate that was
used, retry count of the rate and tx power. It is intended for all
information related to RC and TPC that needs to be passed from driver to
mac80211 and its RC/TPC algorithms like Minstrel_HT. It corresponds to
one stage in an mrr. Multiple subsequent instances of this struct can be
included in struct ieee80211_tx_status via a pointer and a length variable.
Those instances can be allocated on-stack. The former reference to a single
instance of struct rate_info is replaced with our new annotation.
An extension is introduced to struct ieee80211_hw. There are two new
members called 'tx_power_levels' and 'max_txpwr_levels_idx' acting as a
tx power level table. When a wifi device is registered, the driver shall
supply all supported power levels in this list. This allows to support
several quirks like differing power steps in power level ranges or
alike. TPC can use this for algorithm and thus be designed more abstract
instead of handling all possible step widths individually.
Further mandatory changes in status.c, mt76 and ath11k drivers due to the
removal of 'struct rate_info *rate' are also included.
status.c already uses the information in ieee80211_tx_status->rate in
radiotap, this is now changed to use ieee80211_rate_status->rate_idx.
mt76 driver already uses struct rate_info to pass the tx rate to status
path. The new members of the ieee80211_tx_status are set to NULL and 0
because the previously passed rate is not relevant to rate control and
accurate information is passed via tx_info->status.rates.
For ath11k, the txrate can be passed via this struct because ath11k uses
firmware RC and thus the information does not interfere with software RC.
Compile-Tested: current wireless-next tree with all flags on
Tested-on: Xiaomi 4A Gigabit (MediaTek MT7603E, MT7612E) with OpenWrt
Linux 5.10.113
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://lore.kernel.org/r/20220509173958.1398201-2-jelonek.jonas@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add ieee80211_rx_check_bss_color_collision routine in order to introduce
BSS color collision detection in mac80211 if it is not supported in HW/FW
(e.g. for mt7915 chipset).
Add IEEE80211_HW_DETECTS_COLOR_COLLISION flag to let the driver notify
BSS color collision detection is supported in HW/FW. Set this for ath11k
which apparently didn't need this code.
Tested-by: Peter Chiu <Chui-Hao.Chiu@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/a05eeeb1841a84560dc5aaec77894fcb69a54f27.1648204871.git.lorenzo@kernel.org
[clarify commit message a bit, move flag to mac80211]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The comment above the ieee80211_tx_info_clear_status() helper was somewhat
confusing as to which fields it was or wasn't clearing. So replace it by
something that is hopefully more, well, clear.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220404210108.2684907-1-toke@toke.dk
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new fields in struct beacon_data to store all MBSSID elements.
Generate a beacon template which includes all MBSSID elements.
Move CSA offset to reflect the MBSSID element length.
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Money Wang <money.wang@mediatek.com>
Link: https://lore.kernel.org/r/5322db3c303f431adaf191ab31c45e151dde5465.1645702516.git.lorenzo@kernel.org
[small cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently in case of target hardware restart, we just reconfig and
re-enable the security keys and enable the network queues to start
data traffic back from where it was interrupted.
Many ath10k wifi chipsets have sequence numbers for the data
packets assigned by firmware and the mac sequence number will
restart from zero after target hardware restart leading to mismatch
in the sequence number expected by the remote peer vs the sequence
number of the frame sent by the target firmware.
This mismatch in sequence number will cause out-of-order packets
on the remote peer and all the frames sent by the device are dropped
until we reach the sequence number which was sent before we restarted
the target hardware
In order to fix this, we trigger a sta disconnect, in case of target
hw restart. After this there will be a fresh connection and thereby
avoiding the dropping of frames by remote peer.
The right fix would be to pull the entire data path into the host
which is not feasible or would need lots of complex changes and
will still be inefficient.
Tested on ath10k using WCN3990, QCA6174
Signed-off-by: Youghandhar Chintala <youghand@codeaurora.org>
Link: https://lore.kernel.org/r/20220308115325.5246-2-youghand@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The size of the status_driver_data field was not adjusted when
the is_valid_ack_signal field was added.
Since the size of struct ieee80211_tx_info is limited, replace
the is_valid_ack_signal field with a flags field, and adjust the
struct size accordingly.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.0ff363d4fa56.I45792c0187034a6d0e1c99a7db741996ef7caba3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_iterate_active_interfaces() and
ieee80211_iterate_active_interfaces_atomic() already exist, where the
former allows the iterator function to sleep. Add
ieee80211_iterate_stations() which is similar to
ieee80211_iterate_stations_atomic() but allows the iterator to sleep.
This is needed for adding SDIO support to the rtw88 driver. Some
interators there are reading or writing registers. With the SDIO ops
(sdio_readb, sdio_writeb and friends) this means that the iterator
function may sleep.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211228211501.468981-2-martin.blumenstingl@googlemail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ETSI standard defines "Offchannel CAC" as:
"Off-Channel CAC is performed by a number of non-continuous checks
spread over a period in time. This period, which is required to
determine the presence of radar signals, is defined as the Off-Channel
CAC Time..
Minimum Off-Channel CAC Time 6 minutes and Maximum Off-Channel CAC Time
4 hours..".
mac80211 implementation refers to a dedicated hw chain used for continuous
radar monitoring. Rename offchannel_* references to background_* in
order to avoid confusion with ETSI standard.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/4204cc1d648d76b44557981713231e030a3bd991.1638190762.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce a disconnect function that can be used when a
channel switch error occurs. The channel switch can request to
block the tx, and so, we need to make sure we do not send a deauth
frame in this case.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.cd2a615a0702.I9edb14785586344af17644b610ab5be109dcef00@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring fields.
Use memset_after() so memset() doesn't get confused about writing
beyond the destination member that is intended to be the starting point
of zeroing through the end of the struct.
Additionally fix the common helper, ieee80211_tx_info_clear_status(),
which was not clearing ack_signal, but the open-coded versions
did. Johannes Berg points out this bug was introduced by commit
e3e1a0bcb3 ("mac80211: reduce IEEE80211_TX_MAX_RATES") but was harmless.
Also drops the associated unneeded BUILD_BUG_ON()s, and adds a note to
carl9170 about usage.
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Christian Lamparter <chunkeey@gmail.com> [both CARL9170+P54USB on real HW]
Link: https://lore.kernel.org/r/20211118203839.1289276-1-keescook@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers to provide a destination device + info for flow offload
Only supported in combination with 802.3 encap offload
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20211112112223.1209-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Similar to cfg80211, introduce set_radar_offchan callback in mac80211_ops
in order to configure a dedicated offchannel chain available on some hw
(e.g. mt7915) to perform offchannel CAC detection and avoid tx/rx downtime.
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/201110606d4f3a7dfdf31440e351f2e2c375d4f0.1634979655.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* the applicable eth_hw_addr_set() and const hw_addr changes
* various code cleanups/refactorings
* stack usage reductions across the wireless stack
* some unstructured find_ie() -> structured find_element()
changes
* a few more pieces of multi-BSSID support
* some 6 GHz regulatory support
* 6 GHz support in hwsim, for testing userspace code
* Light Communications (LC, 802.11bb) early band definitions
to be able to add a first driver soon
-----BEGIN PGP SIGNATURE-----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=ZXrI
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Quite a few changes:
* the applicable eth_hw_addr_set() and const hw_addr changes
* various code cleanups/refactorings
* stack usage reductions across the wireless stack
* some unstructured find_ie() -> structured find_element()
changes
* a few more pieces of multi-BSSID support
* some 6 GHz regulatory support
* 6 GHz support in hwsim, for testing userspace code
* Light Communications (LC, 802.11bb) early band definitions
to be able to add a first driver soon
* tag 'mac80211-next-for-net-next-2021-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (35 commits)
cfg80211: fix kernel-doc for MBSSID EMA
mac80211: Prevent AP probing during suspend
nl80211: Add LC placeholder band definition to nl80211_band
...
====================
Link: https://lore.kernel.org/r/20211021154953.134849-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Configure multiple BSSID and enhanced multi-BSSID advertisement (EMA)
parameters in mac80211 for AP mode.
For each interface, 'mbssid_tx_vif' points to the transmitting interface of
the MBSSID set. The pointer is set to NULL if MBSSID is disabled.
Function ieee80211_stop() is modified to always bring down all the
non-transmitting interfaces first and the transmitting interface last.
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/20210916025437.29138-3-alokad@codeaurora.org
[slightly change logic to be more obvious]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is to save the transmit power envelope element and power
constraint in struct ieee80211_bss_conf for 6 GHz. Lower driver
will use this info to calculate the power limit.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/20210924100052.32029-7-wgong@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
6 GHz regulatory domains introduces different modes for 6 GHz AP
operations: Low Power Indoor (LPI), Standard Power (SP) and Very
Low Power (VLP). 6 GHz STAs could be operated as either Regular or
Subordinate clients. Define the flags for power type
of AP and STATION mode.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/20210924100052.32029-2-wgong@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
@IEEE80211_KEY_FLAG_GENERATE_IV setting is irrelevant for RX.
Move the requirement to the correct section in the PTK0 rekey
documentation.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20210924200514.7936-1-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce TWT action frames parsing support to mac80211.
Currently just individual TWT agreement are support in AP mode.
Whenever the AP receives a TWT action frame from an associated client,
after performing sanity checks, it will notify the underlay driver with
requested parameters in order to check if they are supported and if there
is enough room for a new agreement. The driver is expected to set the
agreement result and report it to mac80211.
Drivers supporting this have two new callbacks:
- add_twt_setup (mandatory)
- twt_teardown_request (optional)
mac80211 will send an action frame reply according to the result
reported by the driver.
Tested-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/257512f2e22ba42b9f2624942a128dd8f141de4b.1629741512.git.lorenzo@kernel.org
[use le16p_replace_bits(), minor cleanups, use (void *) casts,
fix to use ieee80211_get_he_iftype_cap() correctly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The color change announcement is very similar to how CSA works where
we have an IE that includes a counter. When the counter hits 0, the new
color is applied via an updated beacon.
This patch makes the CSA counter functionality reusable, rather than
implementing it again. This also allows for future reuse incase support
for other counter IEs gets added.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/057c1e67b82bee561ea44ce6a45a8462d3da6995.1625247619.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This switches the airtime scheduler in mac80211 to use a virtual
time-based scheduler instead of the round-robin scheduler used before.
This has a couple of advantages:
- No need to sync up the round-robin scheduler in firmware/hardware with
the round-robin airtime scheduler.
- If several stations are eligible for transmission we can schedule both
of them; no need to hard-block the scheduling rotation until the head
of the queue has used up its quantum.
- The check of whether a station is eligible for transmission becomes
simpler (in ieee80211_txq_may_transmit()).
The drawback is that scheduling becomes slightly more expensive, as we
need to maintain an rbtree of TXQs sorted by virtual time. This means
that ieee80211_register_airtime() becomes O(logN) in the number of
currently scheduled TXQs because it can change the order of the
scheduled stations. We mitigate this overhead by only resorting when a
station changes position in the tree, and hopefully N rarely grows too
big (it's only TXQs currently backlogged, not all associated stations),
so it shouldn't be too big of an issue.
To prevent divisions in the fast path, we maintain both station sums and
pre-computed reciprocals of the sums. This turns the fast-path operation
into a multiplication, with divisions only happening as the number of
active stations change (to re-compute the current sum of all active
station weights). To prevent this re-computation of the reciprocal from
happening too frequently, we use a time-based notion of station
activity, instead of updating the weight every time a station gets
scheduled or de-scheduled. As queues can oscillate between empty and
occupied quite frequently, this can significantly cut down on the number
of re-computations. It also has the added benefit of making the station
airtime calculation independent on whether the queue happened to have
drained at the time an airtime value was accounted.
Co-developed-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210623134755.235545-1-toke@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have mgd_prepare_tx(), but sometimes drivers may want/need
to take action when the exchange finishes, whether successfully
or not.
Add a notification to the driver on completion, i.e. call the
new method mgd_complete_tx().
To unify the two scenarios, and to add more information, make
both of them take a struct that has the duration (prepare only),
subtype (both) and success (complete only).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.5d94e78f6230.I6dc979606b6f28701b740d7aab725f7853a5a155@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This avoids calling back into tx handlers from within the rate control module.
Preparation for deferring rate control until tx dequeue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210617163113.75815-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a helper function that checks if a frame is a data frame. Frames
with hardware encapsulation enabled are data frames.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
Link: https://lore.kernel.org/r/20210519122019.92359-2-borgers@mi.fu-berlin.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The commit cb17ed29a7 ("mac80211: parse radiotap header when selecting Tx
queue") moved the code to validate the radiotap header from
ieee80211_monitor_start_xmit to ieee80211_parse_tx_radiotap. This made is
possible to share more code with the new Tx queue selection code for
injected frames. But at the same time, it now required the call of
ieee80211_parse_tx_radiotap at the beginning of functions which wanted to
handle the radiotap header. And this broke the rate parser for radiotap
header parser.
The radiotap parser for rates is operating most of the time only on the
data in the actual radiotap header. But for the 802.11a/b/g rates, it must
also know the selected band from the chandef information. But this
information is only written to the ieee80211_tx_info at the end of the
ieee80211_monitor_start_xmit - long after ieee80211_parse_tx_radiotap was
already called. The info->band information was therefore always 0
(NL80211_BAND_2GHZ) when the parser code tried to access it.
For a 5GHz only device, injecting a frame with 802.11a rates would cause a
NULL pointer dereference because local->hw.wiphy->bands[NL80211_BAND_2GHZ]
would most likely have been NULL when the radiotap parser searched for the
correct rate index of the driver.
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Fixes: cb17ed29a7 ("mac80211: parse radiotap header when selecting Tx queue")
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
[sven@narfation.org: added commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20210530133226.40587-1-sven@narfation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit a05829a722 ("cfg80211: avoid holding the RTNL when calling the
driver") dropped usage of RTNL here and replaced it with
hw->wiphy->mutex. But we didn't update the comments.
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20210505202829.1039400-1-briannorris@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow the low level driver to get the wdev during
the add_interface flow.
In order to do that, remove a few checks from there and do
not return NULL for vifs that were not yet added to the
driver. Note that all the current callers of this helper
function assume that the vif already exists:
- The callers from the drivers already have a vif pointer.
Before this change, ieee80211_vif_to_wdev would return NULL
in some cases, but those callers don't even check they
get a non-NULL pointer from ieee80211_vif_to_wdev.
- The callers from net/mac80211/cfg.c assume the vif is
already added to the driver as well.
So, this change has no impact on existing callers of this
helper function.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.6078d3517095.I1907a45f267a62dab052bcc44428aa7a2005ffc9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some HW/driver can support passing ethernet rx decap frames and
raw 802.11 frames for the monitor interface concurrently and
via separate RX calls to mac80211. Packets going to the monitor
interface(s) would be in 802.11 format and thus not have the
RX_FLAG_8023 set, and 802.11 format monitoring frames should have
RX_FLAG_ONLY_MONITOR set.
Drivers doing such can enable the SUPPORTS_CONC_MON_RX_DECAP to
allow using ethernet decap offload while a monitor interface is
active, currently RX decapsulation offload gets disabled when a
monitor interface is added.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Link: https://lore.kernel.org/r/1617068116-32253-1-git-send-email-srirrama@codeaurora.org
[add proper documentation, rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, _everything_ in cfg80211 holds the RTNL, and if you
have a slow USB device (or a few) you can get some bad lock
contention on that.
Fix that by re-adding a mutex to each wiphy/rdev as we had at
some point, so we have locking for the wireless_dev lists and
all the other things in there, and also so that drivers still
don't have to worry too much about it (they still won't get
parallel calls for a single device).
Then, we can restrict the RTNL to a few cases where we add or
remove interfaces and really need the added protection. Some
of the global list management still also uses the RTNL, since
we need to have it anyway for netdev management, but we only
hold the RTNL for very short periods of time here.
Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers to pass 802.3 frames to mac80211, with some restrictions:
- the skb must be passed with a valid sta
- fast-rx needs to be active for the sta
- monitor mode needs to be disabled
mac80211 will tell the driver when it is safe to enable rx decap offload for
a particular station.
In order to implement support, a driver must:
- call ieee80211_hw_set(hw, SUPPORTS_RX_DECAP_OFFLOAD)
- implement ops->sta_set_decap_offload
- mark 802.3 frames with RX_FLAG_8023
If it doesn't want to enable offload for some vif types, it can mask out
IEEE80211_OFFLOAD_DECAP_ENABLED in vif->offload_flags from within the
.add_interface or .update_vif_offload driver ops
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201218184718.93650-6-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A stray @ caused the kernel-doc parser to not understand
this, fix that. Also add some missing kernel-doc.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 6bdb68cef7 ("nl80211: add common API to configure SAR power limitations")
Fixes: c534e093d8 ("mac80211: add ieee80211_set_sar_specs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au> # build only
Link: https://lore.kernel.org/r/20210106234740.96827c18f9bd.I8b9f0a9cbfe186931ef9640046f414371f216914@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This change registers ieee80211_set_sar_specs to
mac80211_config_ops, so cfg80211 can call it.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Abhishek Kumar <kuabhs@chromium.org>
Link: https://lore.kernel.org/r/20201203103728.3034-3-cjhuang@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support the driver incrementing MIC error and replay detected
counters when having detected a bad frame, if it drops it directly
instead of relying on mac80211 to do the checks.
These are then exposed to userspace, though currently only in some
cases and in debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201129172929.fb59be9c6de8.Ife2260887366f585afadd78c983ebea93d2bb54b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* injection/radiotap updates for new test capabilities
* remove WDS support - even years ago when we turned
it off by default it was already basically unusable
* support for HE (802.11ax) rates for beacons
* support for some vendor-specific HE rates
* many other small features/cleanups
-----BEGIN PGP SIGNATURE-----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=TGgF
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some updates:
* injection/radiotap updates for new test capabilities
* remove WDS support - even years ago when we turned
it off by default it was already basically unusable
* support for HE (802.11ax) rates for beacons
* support for some vendor-specific HE rates
* many other small features/cleanups
* tag 'mac80211-next-for-net-next-2020-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (21 commits)
nl80211: fix kernel-doc warning in the new SAE attribute
cfg80211: remove WDS code
mac80211: remove WDS-related code
rt2x00: remove WDS code
b43legacy: remove WDS code
b43: remove WDS code
carl9170: remove WDS code
ath9k: remove WDS code
wireless: remove CONFIG_WIRELESS_WDS
mac80211: assure that certain drivers adhere to DONT_REORDER flag
mac80211: don't overwrite QoS TID of injected frames
mac80211: adhere to Tx control flag that prevents frame reordering
mac80211: add radiotap flag to assure frames are not reordered
mac80211: save HE oper info in BSS config for mesh
cfg80211: add support to configure HE MCS for beacon rate
nl80211: fix beacon tx rate mask validation
nl80211/cfg80211: fix potential infinite loop
cfg80211: Add support to calculate and report 4096-QAM HE rates
cfg80211: Add support to configure SAE PWE value to drivers
ieee80211: Add definition for WFA DPP
...
====================
Link: https://lore.kernel.org/r/20201113101148.25268-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a new radiotap flag to indicate injected frames must not be
reordered relative to other frames that also have this flag set,
independent of priority field values in the transmitted frame.
Parse this radiotap flag and define and set a corresponding Tx
control flag. Note that this flag has recently been standardized
as part of an update to radiotap.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20201104061823.197407-2-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently he_support is set only for AP mode. Storing this
information for mesh BSS as well helps driver to determine
HE support. Also save HE operation element params in BSS
conf so that drivers can access this for any configurations
instead of having to parse the beacon to fetch that info.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Link: https://lore.kernel.org/r/20201020183111.25458-2-pradeepc@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some identifiers have different names between their prototypes
and the kernel-doc markup.
Others need to be fixed, as kernel-doc markups should use this format:
identifier - description
In the specific case of __sta_info_flush(), add a documentation
for sta_info_flush(), as this one is the one used outside
sta_info.c.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Link: https://lore.kernel.org/r/978d35eef2dc76e21c81931804e4eaefbd6d635e.1603469755.git.mchehab+huawei@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The user is allowed to change beacon tx rate (HT/VHT/HE) from hostapd.
This information needs to be passed to the driver when the rate control
is offloaded to the firmware. The driver capability of allowing beacon
rate is already validated in cfg80211, so simply passing the rate
information to the driver is enough.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Link: https://lore.kernel.org/r/1601762658-15627-1-git-send-email-rmanohar@codeaurora.org
[adjust commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow drivers to request that interface-iterator does NOT iterate
over interfaces that are not sdata-in-driver. This will allow
us to fix crashes in ath10k (and possibly other drivers).
To summarize Johannes' explanation:
Consider
add interface wlan0
add interface wlan1
iterate active interfaces -> wlan0 wlan1
add interface wlan2
iterate active interfaces -> wlan0 wlan1 wlan2
If you apply this scenario to a restart, which ought to be functionally
equivalent to the normal startup, just compressed in time, you're
basically saying that today you get
add interface wlan0
add interface wlan1
iterate active interfaces -> wlan0 wlan1 wlan2 << problem here
add interface wlan2
iterate active interfaces -> wlan0 wlan1 wlan2
which yeah, totally seems wrong.
But fixing that to be
add interface wlan0
add interface wlan1
iterate active interfaces ->
<nothing>
add interface wlan2
iterate active interfaces -> <nothing>
(or
maybe -> wlan0 wlan1 wlan2 if the reconfig already completed)
This is also at least somewhat wrong, but better to not iterate
over something that exists in the driver than iterate over something
that does not. Originally the first issue was causing crashes in
testing with lots of station vdevs on an ath10k radio, combined
with firmware crashing.
I ran with a similar patch for years with no obvious bad results,
including significant testing with ath9k and ath10k.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20200922191957.25257-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The changes required for associating in S1G are:
- apply S1G BSS channel info before assoc
- mark all S1G STAs as QoS STAs
- include and parse AID request element
- handle new Association Response format
- don't fail assoc if supported rates element is missing
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-15-thomas@adapt-ip.com
[pass skb to ieee80211_add_aid_request_ie(), remove unused variable 'bss']
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G doesn't have legacy (sband->bitrates) rates, only MCS.
For now, just send a frame at MCS 0 if a low rate is
requested. Note we also redefine (since we're out of TX
flags) TX_RC_VHT_MCS as TX_RC_S1G_MCS to indicate an S1G
MCS. This is probably OK as VHT MCS is not valid on S1G
band and vice versa.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-12-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds mac80211 support to configure unsolicited
broadcast probe response transmission for in-band discovery in 6GHz.
Changes include functions to store and retrieve probe response template,
and packet interval (0 - 20 TUs).
Setting interval to 0 disables the unsolicited broadcast probe response
transmission.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/010101747a946b35-ad25858a-1f1f-48df-909e-dc7bf26d9169-000000@us-west-2.amazonses.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to unify the tx status path, the hw 802.11 encapsulation flag
needs to survive the trip to the tx status call.
Since we don't have any free bits in info->flags, we need to move one.
IEEE80211_TX_INTFL_NEED_TXPROCESSING is only used internally in mac80211,
and only before the call into the driver.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-10-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All drivers using airtime fairness are calling ieee80211_sta_register_airtime
directly, now they must. Document this as well.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-8-nbd@nbd.name
[johannes: update the documentation to suit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current API (which lets the driver turn on/off per vif directly) has a
number of limitations:
- it does not deal with AP_VLAN
- conditions for enabling (no tkip, no monitor) are only checked at
add_interface time
- no way to indicate 4-addr support
In order to address this, store offload flags in struct ieee80211_vif
(easy to extend for decap offload later). mac80211 initially sets the enable
flag, but gives the driver a chance to modify it before its settings are
applied. In addition to the .add_interface op, a .update_vif_offload op is
introduced, which can be used for runtime changes.
If a driver can't disable encap offload at runtime, or if it has some extra
limitations, it can simply override the flags within those ops.
Support for encap offload with 4-address mode interfaces can be enabled
by setting a flag from .add_interface or .update_vif_offload.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-6-nbd@nbd.name
[resolved conflict with commit aa2092a9ba ("ath11k: add raw mode and
software crypto support")]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We want to reuse the functions and structs for other counters such as BSS
color change. Rename them to more generic names.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200811080107.3615705-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be used to run mac80211 rx processing on a batch of frames in NAPI
poll before passing them to the network stack in a large batch.
This can improve icache footprint, or it can be used to pass frames via
netif_receive_skb_list.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200726110611.46886-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Already parse the radiotap header in ieee80211_monitor_select_queue.
In a subsequent commit this will allow us to add a radiotap flag that
influences the queue on which injected packets will be sent.
This also fixes the incomplete validation of the injected frame in
ieee80211_monitor_select_queue: currently an out of bounds memory
access may occur in in the called function ieee80211_select_queue_80211
if the 802.11 header is too small.
Note that in ieee80211_monitor_start_xmit the radiotap header is parsed
again, which is necessairy because ieee80211_monitor_select_queue is not
always called beforehand.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-6-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The radiotap specification contains a flag to indicate that the sequence
number of an injected frame should not be overwritten. Parse this flag
and define and set a corresponding Tx control flag.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-2-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200507185907.GA15102@embeddedor
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
-----BEGIN PGP SIGNATURE-----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=MVBJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As of now HE operation element in bss_conf includes variable length
optional field followed by other HE variable. Though the optional
field never be used, actually it is referring to next member of the
bss_conf structure which is not correct. Fix it by declaring needed
HE operation fields within bss_conf itself.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Link: https://lore.kernel.org/r/1587768108-25248-2-git-send-email-rmanohar@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
RX status needs a KHz component, so add freq_offset. We
can reduce the bits for the frequency since 60 GHz isn't
supported.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-5-thomas@adapt-ip.com
[fix commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Driver tells mac80211 to sends ADDBA with SSN (starting sequence number)
from the head of the queue, while the transmission of all the frames in the
queue may take a while, which causes the peer to time out. In order to
fix this scenario, add an option to defer ADDBA transmit until queue
is drained.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200326150855.0f27423fec75.If67daab123a27c1cbddef000d6a3f212aa6309ef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert a user space registration for processing multicast Action frames
(NL80211_CMD_REGISTER_FRAME with NL80211_ATTR_RECEIVE_MULTICAST) to a
new enum ieee80211_filter_flags bit FIF_MCAST_ACTION so that drivers can
update their RX filter parameters appropriately, if needed.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200421144815.19175-1-jouni@codeaurora.org
[rename variables to rx_mcast_action_reg indicating action frames only]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When fixing the initialization race, we neglected to account for
the fact that debugfs is initialized in wiphy_register(), and
some debugfs things went missing (or rather were rerooted to the
global debugfs root).
Fix this by adding debugfs entries only after wiphy_register().
This requires some changes in the rate control code since it
currently adds debugfs at alloc time, which can no longer be
done after the reordering.
Reported-by: Jouni Malinen <j@w1.fi>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Felix Fietkau <nbd@nbd.name>
Cc: stable@vger.kernel.org
Fixes: 52e04b4ce5 ("mac80211: fix race in ieee80211_register_hw()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200423111344.0e00d3346f12.Iadc76a03a55093d94391fc672e996a458702875d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement drv_set_tid_config api to allow TID specific
configuration and drv_reset_tid_config api to reset peer
specific TID configuration. This per-TID onfiguration
will be applied for all the connected stations when MAC is NULL.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-7-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
-----BEGIN PGP SIGNATURE-----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=CgmJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few big new things:
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With multiple VIFS ath10k, and probably others, tries to find the
minimum txpower for all vifs and uses that when setting txpower in
the firmware.
If a second vif is added and starts to scan, it's txpower is not
initialized yet and it set to zero.
ath10k had a patch to ignore zero values, but then it is impossible
to actually set txpower to zero.
So, instead initialize the txpower to INT_MIN in mac80211, and let
drivers know that means the power has not been set and so should
be ignored.
This should fix regression in:
commit 88407beb1b
Author: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Date: Tue Dec 13 14:55:19 2016 -0800
ath10k: fix incorrect txpower set by P2P_DEVICE interface
Tested on ath10k 9984 with ath10k-ct firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20191217183057.24586-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It turns out that this wasn't a good idea, I hit a test failure in
hwsim due to this. That particular failure was easily worked around,
but it raised questions: if an AP needs to, for example, send action
frames to each connected station, the current limit is nowhere near
enough (especially if those stations are sleeping and the frames are
queued for a while.)
Shuffle around some bits to make more room for ack_frame_id to allow
up to 8192 queued up frames, that's enough for queueing 4 frames to
each connected station, even at the maximum of 2007 stations on a
single AP.
We take the bits from band (which currently only 2 but I leave 3 in
case we add another band) and from the hw_queue, which can only need
4 since it has a limit of 16 queues.
Fixes: 6912daed05 ("mac80211: Shrink the size of ack_frame_id to make room for tx_time_est")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200115122549.b9a4ef9f4980.Ied52ed90150220b83a280009c590b65d125d087c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is now possible to propagate BSS color settings into the subsystem. Lets
make mac80211 also handle them so that we can send them further down the
stack into the drivers. We drop the old bss_color field and change iwlwifi
to use the new he_bss_color struct.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20191217141921.8114-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds a new transmit path for hardware that supports 802.11
encapsulation offloading. In those cases 802.3 frames get passed
directly to the driver allowing the hardware to handle the encapsulation.
Some features such as monitor mode and TKIP would break when encapsulation
offloading is enabled. If any of these get enabled, the code will alwyas
fallback to the normal sw encapsulation data path.
The patch defines a secondary netdev_ops struct that the device gets
assigned if 802.11 encap support is available and enabled. The driver
needs to enable the support on a per vif basis if it finds that all
pre-reqs are meet.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20191125100438.16539-1-john@phrozen.org
[reword comments, remove SUPPORTS_80211_ENCAP HW flag, minor cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The previous commit added the ability to throttle stations when they queue
too much airtime in the hardware. This commit enables the functionality by
calculating the expected airtime usage of each packet that is dequeued from
the TXQs in mac80211, and accounting that as pending airtime.
The estimated airtime for each skb is stored in the tx_info, so we can
subtract the same amount from the running total when the skb is freed or
recycled. The throttling mechanism relies on this accounting to be
accurate (i.e., that we are not freeing skbs without subtracting any
airtime they were accounted for), so we put the subtraction into
ieee80211_report_used_skb(). As an optimisation, we also subtract the
airtime on regular TX completion, zeroing out the value stored in the
packet afterwards, to avoid having to do an expensive lookup of the station
from the packet data on every packet.
This patch does *not* include any mechanism to wake a throttled TXQ again,
on the assumption that this will happen anyway as a side effect of whatever
freed the skb (most commonly a TX completion).
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-5-kyan@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order for the Fq_CoDel algorithm integrated in mac80211 layer to operate
effectively to control excessive queueing latency, the CoDel algorithm
requires an accurate measure of how long packets stays in the queue, AKA
sojourn time. The sojourn time measured at the mac80211 layer doesn't
include queueing latency in the lower layer (firmware/hardware) and CoDel
expects lower layer to have a short queue. However, most 802.11ac chipsets
offload tasks such TX aggregation to firmware or hardware, thus have a deep
lower layer queue.
Without a mechanism to control the lower layer queue size, packets only
stay in mac80211 layer transiently before being sent to firmware queue.
As a result, the sojourn time measured by CoDel in the mac80211 layer is
almost always lower than the CoDel latency target, hence CoDel does little
to control the latency, even when the lower layer queue causes excessive
latency.
The Byte Queue Limits (BQL) mechanism is commonly used to address the
similar issue with wired network interface. However, this method cannot be
applied directly to the wireless network interface. "Bytes" is not a
suitable measure of queue depth in the wireless network, as the data rate
can vary dramatically from station to station in the same network, from a
few Mbps to over Gbps.
This patch implements an Airtime-based Queue Limit (AQL) to make CoDel work
effectively with wireless drivers that utilized firmware/hardware
offloading. AQL allows each txq to release just enough packets to the lower
layer to form 1-2 large aggregations to keep hardware fully utilized and
retains the rest of the frames in mac80211 layer to be controlled by the
CoDel algorithm.
Signed-off-by: Kan Yan <kyan@google.com>
[ Toke: Keep API to set pending airtime internal, fix nits in commit msg ]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-4-kyan@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix recently added code to calculate airtime of packets to the mt76
driver. Import this into mac80211 so we can use it for airtime queue limit
calculations.
The airtime.c file is copied verbatim from the mt76 driver, and adjusted to
be usable in mac80211. This involves:
- Switching to mac80211 data structures.
- Adding support for 160 MHz channels and HE mode.
- Moving the symbol and duration calculations around a bit to avoid
rounding with the higher rates and longer symbol times used for HE rates.
The per-rate TX rate calculation is also split out to its own function so
it can be used directly for the AQL calculations later.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-3-kyan@google.com
[fix HE_GROUP_IDX() to use 3 * bw, since there are 3 _gi values]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To implement airtime queue limiting, we need to keep a running account of
the estimated airtime of all skbs queued into the device. Do to this
correctly, we need to store the airtime estimate into the skb so we can
decrease the outstanding balance when the skb is freed. This means that the
time estimate must be stored somewhere that will survive for the lifetime
of the skb.
To get this, decrease the size of the ack_frame_id field to 6 bits, and
lower the size of the ID space accordingly. This leaves 10 bits for use for
tx_time_est, which is enough to store a maximum of 4096 us, if we shift the
values so they become units of 4us.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/157182474063.150713.16132669599100802716.stgit@toke.dk
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
