DisplayPort requires per-segment link training when LTTPR are switched
to non-transparent mode, starting with LTTPR closest to the source.
Only when each segment is trained individually, source can link train
to sink.
Implement per-segment link traning when LTTPR(s) are detected, to
support external docking stations. On higher level, changes are:
* Pass phy being trained down to all required helpers
* Run CR, EQ link training per phy
* Set voltage swing, pre-emphasis levels per phy
Since at least some LTTPRs (eg. Parade PS8830) do not correctly report
voltage-swing, pre-emphasis level 3 support, always assume level 3 is
supported. This is permitted under DP 2.1(a) section 3.6.7.2 stating
that LTTPR shall set its transmitter levels as close as possible to
those requested by the DPTX, if the DPTX sets the voltage swing or
pre-emphasis to a level that the LTTPR does not support. It shall be
noted that LTTPR’s level choosing is implementation-specific.
This ensures successful link training both when connected directly to
the monitor (single LTTPR onboard most X1E laptops) and via the docking
station (at least two LTTPRs).
Fixes: 72d0af4acc ("drm/msm/dp: Add support for LTTPR handling")
Tested-by: Jessica Zhang <quic_jesszhan@quicinc.com> # SA8775P
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Tested-by: Stefan Schmidt <stefan.schmidt@linaro.org>
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/652305/
Link: https://lore.kernel.org/r/20250507230113.14270-5-alex.vinarskis@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Per-segment link training requires knowing the number of LTTPRs
(if any) present. Store the count during LTTPRs' initialization.
Fixes: 72d0af4acc ("drm/msm/dp: Add support for LTTPR handling")
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Tested-by: Jessica Zhang <quic_jesszhan@quicinc.com> # SA8775P
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/652306/
Link: https://lore.kernel.org/r/20250507230113.14270-4-alex.vinarskis@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Take into account LTTPR capabilities when selecting maximum allowed
link rate, number of data lines.
Fixes: 72d0af4acc ("drm/msm/dp: Add support for LTTPR handling")
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Tested-by: Jessica Zhang <quic_jesszhan@quicinc.com> # SA8775P
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/652302/
Link: https://lore.kernel.org/r/20250507230113.14270-3-alex.vinarskis@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The MSM DisplayPort driver implements several HDMI codec functions
in the driver, e.g. it manually manages HDMI codec device registration,
returning ELD and plugged_cb support. In order to reduce code
duplication reuse drm_hdmi_audio_* helpers and drm_bridge_connector
integration.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/649728/
Link: https://lore.kernel.org/r/20250423-dp-hdmi-audio-v7-1-8407a23e55b2@oss.qualcomm.com
Backmerging to get v6.15-rc1 into drm-misc-next. Also fixes a
build issue when enabling CONFIG_DRM_SCHED_KUNIT_TEST.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
drm_dp_dpcd_read_link_status() follows the "return error code or number
of bytes read" protocol, with the code returning less bytes than
requested in case of some errors. However most of the drivers
interpreted that as "return error code in case of any error". Switch
drm_dp_dpcd_read_link_status() to drm_dp_dpcd_read_data() and make it
follow that protocol too.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250324-drm-rework-dpcd-access-v4-2-e80ff89593df@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/632406/
Link: https://lore.kernel.org/r/20250114191724.861601-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link Training Tunable PHY Repeaters (LTTPRs) are defined in DisplayPort
1.4a specification. As the name suggests, these PHY repeaters are
capable of adjusting their output for link training purposes.
According to the DisplayPort standard, LTTPRs have two operating
modes:
- non-transparent - it replies to DPCD LTTPR field specific AUX
requests, while passes through all other AUX requests
- transparent - it passes through all AUX requests.
Switching between these two modes is done by the DPTX by issuing
an AUX write to the DPCD PHY_REPEATER_MODE register.
The msm DP driver is currently lacking any handling of LTTPRs.
This means that if at least one LTTPR is found between DPTX and DPRX,
the link training would fail if that LTTPR was not already configured
in transparent mode.
The section 3.6.6.1 from the DisplayPort v2.0 specification mandates
that before link training with the LTTPR is started, the DPTX may place
the LTTPR in non-transparent mode by first switching to transparent mode
and then to non-transparent mode. This operation seems to be needed only
on first link training and doesn't need to be done again until device is
unplugged.
It has been observed on a few X Elite-based platforms which have
such LTTPRs in their board design that the DPTX needs to follow the
procedure described above in order for the link training to be successful.
So add support for reading the LTTPR DPCD caps to figure out the number
of such LTTPRs first. Then, for platforms (or Type-C dongles) that have
at least one such an LTTPR, set its operation mode to transparent mode
first and then to non-transparent, just like the mentioned section of
the specification mandates.
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250203-drm-dp-msm-add-lttpr-transparent-mode-set-v5-4-c865d0e56d6e@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAme7hfkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGU+IH/1bk6zIvAwXXS5yu
KNsQ8dEkC3Xme6HqLtPsAhRLF+5YJf6MaGm1ip5dDMyIvasa2gwvCQQQoOpeMbKj
79VKT+m9t3szMHZaQYjlOuYHBmNSJ4cMCD2Qh6ktXHGPfTTWDFGf7fBwBOkVNeJU
1Ask+bxeop21aJMhfYXrUta3OYyerLBUR6jCiCM82A/GLtdv6oNGXBu3ygDt9Tjx
ZHSl+CYjKpmGUP8JnMKwCBHVguEfqgzZ//dY1H16AvOLed9k2jkMFn8O5Vi3vjnx
TWMMXoiJimuamGzbjxtCCqzxNlFFDT4gRpDqeJxb16W/gDTFmbRr9LDjNehCZe33
AigLZ6M=
=Y/7F
-----END PGP SIGNATURE-----
Merge tag 'v6.14-rc4' into drm-next
Backmerge Linux 6.14-rc4 at the request of tzimmermann so misc-next
can base on rc4.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes for v6.14-rc4
Display:
* More catalog fixes:
- to skip watchdog programming through top block if its not present
- fix the setting of WB mask to ensure the WB input control is programmed
correctly through ping-pong
- drop lm_pair for sm6150 as that chipset does not have any 3dmerge block
* Fix the mode validation logic for DP/eDP to account for widebus (2ppc)
to allow high clock resolutions
* Fix to disable dither during encoder disable as otherwise this was
causing kms_writeback failure due to resource sharing between
* WB and DSI paths as DSI uses dither but WB does not
* Fixes for virtual planes, namely to drop extraneous return and fix
uninitialized variables
* Fix to avoid spill-over of DSC encoder block bits when programming
the bits-per-component
* Fixes in the DSI PHY to protect against concurrent access of
PHY_CMN_CLK_CFG regs between clock and display drivers
Core/GPU:
* Fix non-blocking fence wait incorrectly rounding up to 1 jiffy timeout
* Only print GMU fw version once, instead of each time the GPU resumes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtt2AODBXdod8ULXcAygf_qYvwRDVeUVtODx=2jErp6cA@mail.gmail.com
It's pretty inconvenient to access the full atomic state from
drm_bridges, so let's change the atomic_post_disable hook prototype to
pass it directly.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-5-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
It's pretty inconvenient to access the full atomic state from
drm_bridges, so let's change the atomic_disable hook prototype to pass
it directly.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-4-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
It's pretty inconvenient to access the full atomic state from
drm_bridges, so let's change the atomic_enable hook prototype to pass it
directly.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-3-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Widebus allows the DP controller to operate in 2 pixel per clock mode.
The mode validation logic validates the mode->clock against the max
DP pixel clock. However the max DP pixel clock limit assumes widebus
is already enabled. Adjust the mode validation logic to only compare
the adjusted pixel clock which accounts for widebus against the max DP
pixel clock. Also fix the mode validation logic for YUV420 modes as in
that case as well, only half the pixel clock is needed.
Cc: stable@vger.kernel.org
Fixes: 757a2f36ab ("drm/msm/dp: enable widebus feature for display port")
Fixes: 6db6e56065 ("drm/msm/dp: change clock related programming for YUV420 over DP")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dale Whinham <daleyo@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/635789/
Link: https://lore.kernel.org/r/20250206-dp-widebus-fix-v2-1-cb89a0313286@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Updates for v6.14
MDSS:
- properly described UBWC registers
- added SM6150 (aka QCS615) support
MDP4:
- several small fixes
DPU:
- added SM6150 (aka QCS615) support
- enabled wide planes if virtual planes are enabled (by using two SSPPs for a single plane)
- fixed modes filtering for platforms w/o 3DMux
- fixed DSPP DSPP_2 / _3 links on several platforms
- corrected DSPP definitions on SDM670
- added CWB hardware blocks support
- added VBIF to DPU snapshots
- dropped struct dpu_rm_requirements
DP:
- reworked DP audio support
DSI:
- added SM6150 (aka QCS615) support
GPU:
- Print GMU core fw version
- GMU bandwidth voting for a740 and a750
- Expose uche trap base via uapi
- UAPI error reporting
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsutUu4ff6OpXNXxqf1xaV0rV6oV23VXNRiF0_OEfe72Q@mail.gmail.com
All other submodules pass arguments directly. Drop struct
msm_dp_panel_in that is used to wrap dp_panel's submodule args and pass
all data to msm_dp_panel_get() directly.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Tested-by: Stephen Boyd <swboyd@chromium.org> # sc7180-trogdor
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/629055/
Link: https://lore.kernel.org/r/20241216-fd-dp-audio-fixup-v4-4-f8d1961cf22f@linaro.org
Use msm_dp_utils_pack_sdp_header() and call msm_dp_write_link() directly
to program audio packet data. Use 0 as Packet ID, as it was not
programmed earlier.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # sc7180-trogdor
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/629051/
Link: https://lore.kernel.org/r/20241216-fd-dp-audio-fixup-v4-2-f8d1961cf22f@linaro.org
The msm_dp_panel_dump_regs() and msm_dp_catalog_dump_regs() are not
called anywhere. If there is a necessity to dump registers, the
snapshotting should be used instead. Drop these two functions.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Tested-by: Stephen Boyd <swboyd@chromium.org> # sc7180-trogdor
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/629049/
Link: https://lore.kernel.org/r/20241216-fd-dp-audio-fixup-v4-1-f8d1961cf22f@linaro.org
Reading access to connector->eld can happen at the same time the
drm_edid_to_eld() updates the data. Take the newly added eld_mutex in
order to protect connector->eld from concurrent access.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241206-drm-connector-eld-mutex-v2-7-c9bce1ee8bea@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
dp_ctrl_off_link() was created to handle a case where we received
a cable connect and then get a cable disconnect without the corresponding
dp_display_enable(). For such cases the pixel clock will be off but the
link clock will still be on. dp_ctrl_off_link() handles this case by
turning off the link clock only.
However, the vote removal to the opp table for this case was missed.
Remove the opp table vote in dp_ctrl_off_link().
Fixes: 375a126090 ("drm/msm/dp: tear down main link at unplug handle immediately")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/627487/
Link: https://lore.kernel.org/r/20241205-dp_mst-v1-2-f8618d42a99a@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
MMSS_DP_INTF_CONFIG has already been setup by the main datapath
for DP to account for widebus to be used/unused etc.
In current implementation, TPG only switches the DP controller
to use the main datapath stream OR use the test pattern but expects
the rest of the controller to be already setup.
Keeping the same behavior intact, drop the clearing of MMSS_DP_INTF_CONFIG
from the msm_dp_catalog_panel_tpg_enable() API.
Fixes: 757a2f36ab ("drm/msm/dp: enable widebus feature for display port")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/626888/
Link: https://lore.kernel.org/r/20241202-tpg-v1-2-0fd6b518b914@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
The msm_dp_utils_pack_sdp_header() accepts an unlimited-size u32 pointer
for the header output, while it expects a two-element array. It performs
a sizeof check which is always true on 64-bit platforms (since
sizeof(u32*) is 8) and is always false on 32-bit platforms. It returns
an error code which nobody actually checks.
Fix the function interface to accept u32[2] and return void, skipping
all the checks.
Fixes: 55fb8ffc18 ("drm/msm/dp: add VSC SDP support for YUV420 over DP")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/626806/
Link: https://lore.kernel.org/r/20241202-fd-dp-audio-fixup-v2-2-d9187ea96dad@linaro.org
[quic_abhinavk@quicinc.com: minor fix in the commit message]
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For historical reasons a lot of symbols in the MSM DisplayPort driver
used the generic dp_ prefix. Perform a mass-rename of those symbols to
use msm_dp prefix.
Basically this is a result of the following script:
sed drivers/gpu/drm/msm/dp/* -i -e 's/\<dp_/msm_dp_/g'
sed drivers/gpu/drm/msm/dp/* -i -e 's/"msm_dp_/"dp_/g'
sed drivers/gpu/drm/msm/dp/* -i -e 's/msm_\(dp_sdp_header\|dp_sdp\)\>/\1/g'
Yes, this also results in renaming of several struct fields in addition
to renaming the structs and functions, but I think the simple solution
is better than the more complex one.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410250305.UHKDhtxy-lkp@intel.com/
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/622211/
Link: https://lore.kernel.org/r/20241029-msm-dp-rename-v2-1-13c5c03fad44@linaro.org
Instead of forcing the ycbcr_420_allowed flag to be set on the created
drm_connector, set it on the drm_bridge instance and allow
drm_bridge_connecgtor to propagate it to the drm_connector.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241019-bridge-yuv420-v1-5-d74efac9e4e6@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The Qualcomm SA8775P platform comes with 2 DisplayPort controllers
for each mdss, having different base offsets than the previous
SoCs. The support for all 4 DPTX have been added here, and
validation of only MDSS0 DPTX0 and DPTX1 have been conducted.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Soutrik Mukhopadhyay <quic_mukhopad@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/620320/
Link: https://lore.kernel.org/r/20241018070706.28980-6-quic_mukhopad@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Hardware document indicates that widebus is recommended on DP on all
MDSS chipsets starting version 5.x.x and above.
Follow the guideline and mark widebus support on all relevant
chipsets for DP.
Fixes: 766f705204 ("drm/msm/dp: Remove now unused connector_type from desc")
Fixes: 1b2d98bdd7 ("drm/msm/dp: Add DisplayPort controller for SM8650")
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 757a2f36ab ("drm/msm/dp: enable widebus feature for display port")
Fixes: 1b2d98bdd7 ("drm/msm/dp: Add DisplayPort controller for SM8650")
Patchwork: https://patchwork.freedesktop.org/patch/606556/
Link: https://lore.kernel.org/r/20240730195012.2595980-1-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Before re-starting link training reset the link phy params namely
the pre-emphasis and voltage swing levels otherwise the next
link training begins at the previously cached levels which can result
in link training failures.
Fixes: 8ede2ecc3e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8350-HDK
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/605946/
Link: https://lore.kernel.org/r/20240725220450.131245-1-quic_abhinavk@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Fix the dp_panel_get_supported_bpp() API to return the minimum
supported bpp correctly for relevant cases and use this API
to correct the behavior of DP driver which hard-codes the max supported
bpp to 30.
This is incorrect because the number of lanes and max data rate
supported by the lanes need to be taken into account.
Replace the hardcoded limit with the appropriate math which accounts
for the accurate number of lanes and max data rate.
changes in v2:
- Fix the dp_panel_get_supported_bpp() and use it
- Drop the max_t usage as dp_panel_get_supported_bpp() already
returns the min_bpp correctly now
changes in v3:
- replace min_t with just min as all params are u32
Fixes: c943b4948b ("drm/msm/dp: add displayPort driver support")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/43
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8350-HDK
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/607073/
Link: https://lore.kernel.org/r/20240805202009.1120981-1-quic_abhinavk@quicinc.com
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
The function dp_wait_hpd_asserted() uses pm_runtime_get_sync() and
doesn't care about the return value. Potentially this can lead to
unclocked access if for some reason resuming of the DP controller fails.
Change the function to use pm_runtime_resume_and_get() and return an
error if resume fails.
Fixes: e2969ee302 ("drm/msm/dp: move of_dp_aux_populate_bus() to eDP probe()")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/580137/
Link: https://lore.kernel.org/r/20240226223446.4194079-1-dmitry.baryshkov@linaro.org
[quic_abhinavk@quicinc.com: resolved trivial conflict while rebase]
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The dp_audio read and write operations uses members in struct dp_catalog
for passing arguments and return values. This adds unnecessary
complexity to the implementation, as it turns out after detangling the
logic that no state is actually held in these variables.
Clean this up by using function arguments and return values for passing
the data.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/585350/
Link: https://lore.kernel.org/r/20240328-msm-dp-cleanup-v2-6-a5aed9798d32@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
dp_catalog_panel_timing_cfg() takes 4 arguments, which are passed from
the calling function through members of struct dp_catalog.
No state is maintained other than across this call, so switch to
function arguments to clean up the code.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/585351/
Link: https://lore.kernel.org/r/20240328-msm-dp-cleanup-v2-5-a5aed9798d32@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The dp_aux write operations takes the data to be operated on through a
member of struct dp_catalog, rather than as an argument to the function.
No state is maintained other than across the calling of the functions,
so replace this member with a function argument.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/585346/
Link: https://lore.kernel.org/r/20240328-msm-dp-cleanup-v2-4-a5aed9798d32@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The "desc" member of struct dp_panel is zero-initialized during
allocation and never assigned, resulting in dp_ctrl_use_fixed_nvid()
never returning true. This returned boolean value is passed around but
never acted upon.
Perform constant propagation and remove the traces of "fixed nvid".
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/585344/
Link: https://lore.kernel.org/r/20240328-msm-dp-cleanup-v2-2-a5aed9798d32@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The members of struct dp_debug are no longer used, so the only purpose
of this struct is as a type of the return value of dp_debug_get(), to
signal success/error.
Drop the struct in favor of signalling the result of initialization
using an int, then merge dp_debug_get() with dp_debug_init() to avoid
the unnecessar boilerplate code.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/585343/
Link: https://lore.kernel.org/r/20240328-msm-dp-cleanup-v2-1-a5aed9798d32@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Before the introduction of the wait_hpd_asserted() callback in
commit 841d742f09 ("drm/dp: Add wait_hpd_asserted() callback to struct
drm_dp_aux") the API between panel drivers and DP AUX bus drivers was
that it was up to the AUX bus driver to wait for HPD in the transfer()
function.
Now wait_hpd_asserted() has been added. The two panel drivers that are
DP AUX endpoints use it. See commit 2327b13d6c ("drm/panel-edp: Take
advantage of wait_hpd_asserted() in struct drm_dp_aux") and
commit 3b5765df37 ("drm/panel: atna33xc20: Take advantage of
wait_hpd_asserted() in struct drm_dp_aux"). We've implemented
wait_hpd_asserted() in the MSM DP driver as of commit e2969ee302
("drm/msm/dp: move of_dp_aux_populate_bus() to eDP probe()"). There is
no longer any reason for long wait in the AUX transfer() function.
Remove it.
NOTE: the wait_hpd_asserted() is listed as "optional". That means it's
optional for the DP AUX bus to implement. In the case of the MSM DP
driver we implement it so we can assume it will be called.
ALSO NOTE: the wait wasn't actually _hurting_ anything and wasn't even
causing long timeouts, but it's still nice to get rid of unneeded
code. Specificaly it's not truly needed because to handle other DP
drivers that can't power on as quickly (specifically parade-ps8640) we
already avoid DP AUX transfers for eDP panels that aren't powered
on. See commit 8df1ddb5bf ("drm/dp: Don't attempt AUX transfers when
eDP panels are not powered").
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/583130/
Link: https://lore.kernel.org/r/20240315143621.v2.3.I535606f6d4f7e3e5588bb75c55996f61980183cd@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The DP wait_hpd_asserted() callback is passed a timeout which
indicates how long we should wait for HPD. This timeout was being
ignored in the MSM DP implementation and instead a hardcoded 500 ms
timeout was used. Fix it to use the proper timeout.
As part of this we move the hardcoded 500 ms number into the AUX
transfer function, which isn't given a timeout. The wait in the AUX
transfer function will be removed in a future commit.
Fixes: e2969ee302 ("drm/msm/dp: move of_dp_aux_populate_bus() to eDP probe()")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/583128/
Link: https://lore.kernel.org/r/20240315143621.v2.2.I7758d18a1773821fa39c034b16a12ef3f18a51ee@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
As documented in the description of the transfer() function of
"struct drm_dp_aux", the transfer() function can be called at any time
regardless of the state of the DP port. Specifically if the kernel has
the DP AUX character device enabled and userspace accesses
"/dev/drm_dp_auxN" directly then the AUX transfer function will be
called regardless of whether a DP device is connected.
For eDP panels we have a special rule where we wait (with a 5 second
timeout) for HPD to go high. This rule was important before all panels
drivers were converted to call wait_hpd_asserted() and actually can be
removed in a future commit.
For external DP devices we never checked for HPD. That means that
trying to access the DP AUX character device (AKA `hexdump -C
/dev/drm_dp_auxN`) would very, very slowly timeout. Specifically on my
system:
$ time hexdump -C /dev/drm_dp_aux0
hexdump: /dev/drm_dp_aux0: Connection timed out
real 0m8.200s
We want access to the drm_dp_auxN character device to fail faster than
8 seconds when no DP cable is plugged in.
Let's add a test to make transfers fail right away if a device isn't
plugged in. Rather than testing the HPD line directly, we have the
dp_display module tell us when AUX transfers should be enabled so we
can handle cases where HPD is signaled out of band like with Type C.
Fixes: c943b4948b ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/583127/
Link: https://lore.kernel.org/r/20240315143621.v2.1.I16aff881c9fe82b5e0fc06ca312da017aa7b5b3e@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Both dp_link_adjust_levels() and dp_ctrl_update_vx_px() limit swing and
pre-emphasis to 2, while the real maximum value for the sum of the
voltage swing and pre-emphasis is 3. Fix the DP code to remove this
limitation.
Fixes: c943b4948b ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/577006/
Link: https://lore.kernel.org/r/20240203-dp-swing-3-v1-1-6545e1706196@linaro.org
