DisplayPort requires per-segment link training when LTTPR are switched
to non-transparent mode, starting with LTTPR closest to the source.
Only when each segment is trained individually, source can link train
to sink.
Implement per-segment link traning when LTTPR(s) are detected, to
support external docking stations. On higher level, changes are:
* Pass phy being trained down to all required helpers
* Run CR, EQ link training per phy
* Set voltage swing, pre-emphasis levels per phy
Since at least some LTTPRs (eg. Parade PS8830) do not correctly report
voltage-swing, pre-emphasis level 3 support, always assume level 3 is
supported. This is permitted under DP 2.1(a) section 3.6.7.2 stating
that LTTPR shall set its transmitter levels as close as possible to
those requested by the DPTX, if the DPTX sets the voltage swing or
pre-emphasis to a level that the LTTPR does not support. It shall be
noted that LTTPR’s level choosing is implementation-specific.
This ensures successful link training both when connected directly to
the monitor (single LTTPR onboard most X1E laptops) and via the docking
station (at least two LTTPRs).
Fixes: 72d0af4acc ("drm/msm/dp: Add support for LTTPR handling")
Tested-by: Jessica Zhang <quic_jesszhan@quicinc.com> # SA8775P
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Tested-by: Stefan Schmidt <stefan.schmidt@linaro.org>
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/652305/
Link: https://lore.kernel.org/r/20250507230113.14270-5-alex.vinarskis@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Per-segment link training requires knowing the number of LTTPRs
(if any) present. Store the count during LTTPRs' initialization.
Fixes: 72d0af4acc ("drm/msm/dp: Add support for LTTPR handling")
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Tested-by: Jessica Zhang <quic_jesszhan@quicinc.com> # SA8775P
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/652306/
Link: https://lore.kernel.org/r/20250507230113.14270-4-alex.vinarskis@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Take into account LTTPR capabilities when selecting maximum allowed
link rate, number of data lines.
Fixes: 72d0af4acc ("drm/msm/dp: Add support for LTTPR handling")
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Tested-by: Jessica Zhang <quic_jesszhan@quicinc.com> # SA8775P
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/652302/
Link: https://lore.kernel.org/r/20250507230113.14270-3-alex.vinarskis@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Follow the changes in the commit a2649952f6 ("drm/msm/dpu: remove
DPU_CTL_SPLIT_DISPLAY from CTL blocks on DPU >= 5.0") and remove
DPU_CTL_SPLIT_DISPLAY from the CTL blocks on the SAR2130P platform.
Single CTL is used for all interfaces used by a single path
Fixes: 1785751734 ("drm/msm/dpu: add catalog entry for SAR2130P")
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/651883/
Link: https://lore.kernel.org/r/20250506-dpu-sar2130p-no-split-display-v1-1-b619c0fddea5@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Drop comments about SoC before each 'struct dpu_lm_sub_blks' for given
SoC because it's duplicating the actual name of structure.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/651251/
Link: https://lore.kernel.org/r/20250430-b4-sm8750-display-v5-11-8cab30c3e4df@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The set_active_pipes() callback configures CTL_FETCH_PIPE_ACTIVE and
newer DPU v12.0 comes with CTL_PIPE_ACTIVE, thus rename it to
set_active_fetch_pipes() to better match the purpose.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/651261/
Link: https://lore.kernel.org/r/20250430-b4-sm8750-display-v5-7-8cab30c3e4df@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The HDMI driver already has msm_hdmi_hpd_enable() and
msm_hdmi_hpd_disable() functions. Wire them into the
msm_hdmi_bridge_funcs, so that HPD can be enabled and disabled
dynamically rather than always having HPD events generation enabled.
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250505-fd-hdmi-hpd-v5-13-48541f76318c@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
It is completely not obvious, but the so-called 'hpd' clocks and
regulators are required for the HDMI host to function properly. Merge
pwr and hpd regulators. Use regulators, clocks and pinctrl to implement
proper runtime PM callbacks.
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/651715/
Link: https://lore.kernel.org/r/20250505-fd-hdmi-hpd-v5-9-48541f76318c@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The pm_runtime_get_sync() function is a bad choise for runtime power
management. Switch HDMI driver to pm_runtime_resume_and_get() and add
proper error handling, while we are at it.
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/651713/
Link: https://lore.kernel.org/r/20250505-fd-hdmi-hpd-v5-7-48541f76318c@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The last platform using legacy clock names for HDMI block (APQ8064)
switched to new clock names in 5.16. It's time to stop caring about old
DT, drop hand-coded helpers and switch to clk_bulk_* API.
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/651716/
Link: https://lore.kernel.org/r/20250505-fd-hdmi-hpd-v5-6-48541f76318c@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The only clock which has frequency being set through hpd_freqs is the
"core" aka MDSS_HDMI_CLK clock. It always has the specified frequency,
so we can drop corresponding clk_set_rate() call together with the
hpd_freq infrastructure.
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/651717/
Link: https://lore.kernel.org/r/20250505-fd-hdmi-hpd-v5-5-48541f76318c@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The driver handles the case where gpu fw is not in the initrd. OTOH it
doesn't always handle the case where _some_ fw is in the initrd, but
others are not. In particular the zap fw tends to be signed with an OEM
specific key, so the paths/names differ across devices with the same
SoC/GPU, so we cannot sanely list them with MODULE_FIRMWARE().
So MODULE_FIRMWARE() just ends up causing problems without actually
solving anything. Remove them!
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/652195/
This feature is supposed to be enabled with UBWC v4 or later.
Implementations of this SKU feature an effective UBWC version of 3, so
disable it, in line with the BSP kernel.
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Fixes: 192f4ee3e4 ("drm/msm/a6xx: Add support for Adreno 7c Gen 3 gpu")
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/651759/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add a module param to disable ACD which will help to quickly rule it
out for any GPU issues.
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Tested-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Tested-by: Anthony Ruhier <aruhier@mailbox.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/649349/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fix the following for qmp_get() errors:
1. Correctly handle probe defer for A6x GPUs
2. Ignore other errors because those are okay when GPU ACD is
not required. They are checked again during gpu acd probe.
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Tested-by: Anthony Ruhier <aruhier@mailbox.org>
Patchwork: https://patchwork.freedesktop.org/patch/649346/
Signed-off-by: Rob Clark <robdclark@chromium.org>
When ACD feature is enabled, it triggers some internal calibrations
which result in a pretty long delay during the first HFI perf vote.
So, increase the HFI response timeout to match the downstream driver.
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Tested-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Tested-by: Anthony Ruhier <aruhier@mailbox.org>
Patchwork: https://patchwork.freedesktop.org/patch/649344/
Signed-off-by: Rob Clark <robdclark@chromium.org>
ACD a.k.a Adaptive Clock Distribution is a feature which helps to reduce
the power consumption. In some chipsets, it is also a requirement to
support higher GPU frequencies. This patch adds support for GPU ACD by
sending necessary data to GMU and AOSS. The feature support for the
chipset is detected based on devicetree data.
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Tested-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Tested-by: Anthony Ruhier <aruhier@mailbox.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/649342/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Really the only purpose of this was to limit the address space size to
4GB to avoid 32b rollover problems in 64b pointer math in older sqe fw.
So replace the address_space_size with a quirk limiting the address
space to 4GB. In all other cases, use the SMMU input address size (IAS)
to determine the address space size.
v2: Properly account for vm_start
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/649467/
If the GMU takes too long to respond to an HFI message, we may return
early. If the GMU does eventually respond, and then we send a second
message, we will see the response for the first, throw another error,
and keep going. But we don't currently wait for the interrupt from the
GMU again, so if the second response isn't there immediately we may
prematurely return. This can cause a continuous cycle of missed HFI
messages, and for reasons I don't quite understand the GMU does not shut
down properly when this happens.
Fix this by waiting for the GMU interrupt when we see an empty queue. If
the GMU never responds then the queue really is empty and we quit. We
can't wait for the interrupt when we see a wrong response seqnum because
the GMU might have already queued both responses by the time we clear
the interrupt the first time so we do need to check the queue before
waiting on the interrupt again.
Signed-off-by: Connor Abbott <cwabbott0@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/650013/
Signed-off-by: Rob Clark <robdclark@chromium.org>
There is a small chance that the GPU is already hot during boot. In that
case, the call to of_devfreq_cooling_register() will immediately try to
apply devfreq cooling, as seen in the following crash:
Unable to handle kernel paging request at virtual address 0000000000014110
pc : a6xx_gpu_busy+0x1c/0x58 [msm]
lr : msm_devfreq_get_dev_status+0xbc/0x140 [msm]
Call trace:
a6xx_gpu_busy+0x1c/0x58 [msm] (P)
devfreq_simple_ondemand_func+0x3c/0x150
devfreq_update_target+0x44/0xd8
qos_max_notifier_call+0x30/0x84
blocking_notifier_call_chain+0x6c/0xa0
pm_qos_update_target+0xd0/0x110
freq_qos_apply+0x3c/0x74
apply_constraint+0x88/0x148
__dev_pm_qos_update_request+0x7c/0xcc
dev_pm_qos_update_request+0x38/0x5c
devfreq_cooling_set_cur_state+0x98/0xf0
__thermal_cdev_update+0x64/0xb4
thermal_cdev_update+0x4c/0x58
step_wise_manage+0x1f0/0x318
__thermal_zone_device_update+0x278/0x424
__thermal_cooling_device_register+0x2bc/0x308
thermal_of_cooling_device_register+0x10/0x1c
of_devfreq_cooling_register_power+0x240/0x2bc
of_devfreq_cooling_register+0x14/0x20
msm_devfreq_init+0xc4/0x1a0 [msm]
msm_gpu_init+0x304/0x574 [msm]
adreno_gpu_init+0x1c4/0x2e0 [msm]
a6xx_gpu_init+0x5c8/0x9c8 [msm]
adreno_bind+0x2a8/0x33c [msm]
...
At this point we haven't initialized the GMU at all yet, so we cannot read
the GMU registers inside a6xx_gpu_busy(). A similar issue was fixed before
in commit 6694482a70 ("drm/msm: Avoid unclocked GMU register access in
6xx gpu_busy"): msm_devfreq_init() does call devfreq_suspend_device(), but
unlike msm_devfreq_suspend(), it doesn't set the df->suspended flag
accordingly. This means the df->suspended flag does not match the actual
devfreq state after initialization and msm_devfreq_get_dev_status() will
end up accessing GMU registers, causing the crash.
Fix this by setting df->suspended correctly during initialization.
Cc: stable@vger.kernel.org
Fixes: 6694482a70 ("drm/msm: Avoid unclocked GMU register access in 6xx gpu_busy")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/650772/
Signed-off-by: Rob Clark <robdclark@chromium.org>
The MSM DisplayPort driver implements several HDMI codec functions
in the driver, e.g. it manually manages HDMI codec device registration,
returning ELD and plugged_cb support. In order to reduce code
duplication reuse drm_hdmi_audio_* helpers and drm_bridge_connector
integration.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/649728/
Link: https://lore.kernel.org/r/20250423-dp-hdmi-audio-v7-1-8407a23e55b2@oss.qualcomm.com
The SDM630 platform doesn't have DSC blocks nor does have it DSC
registers in the PINGPONG block. Drop the DPU_PINGPONG_DSC feature bit
from the PINGPONG's feature mask, replacing PINGPONG_SDM845_MASK with
BIT(DPU_PINGPONG_DITHER).
Fixes: 7204df5e7e ("drm/msm/dpu: add support for SDM660 and SDM630 platforms")
Reported-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/640308/
Link: https://lore.kernel.org/r/20250301-dpu-fix-catalog-v2-5-498271be8b50@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Neither DPU driver nor vendor SDE driver do not use TE2 definitions
(and, in case of SDE driver, never did). Semantics of the TE2 feature
bit and .te2 sblk are not completely clear. Drop these bits from the
catalog with the possibility of reintroducing them later if we need to
support ppsplit.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/640305/
Link: https://lore.kernel.org/r/20250301-dpu-fix-catalog-v2-4-498271be8b50@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The MSM8953 platform doesn't have DSC blocks nor does have it DSC
registers in the PINGPONG block. Drop the DPU_PINGPONG_DSC feature bit
from the PINGPONG's feature mask and, as it is the only remaining bit,
drop the .features assignment completely.
Fixes: 7a6109ce1c ("drm/msm/dpu: Add support for MSM8953")
Reported-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/640303/
Link: https://lore.kernel.org/r/20250301-dpu-fix-catalog-v2-3-498271be8b50@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The MSM8917 platform doesn't have DSC blocks nor does have it DSC
registers in the PINGPONG block. Drop the DPU_PINGPONG_DSC feature bit
from the PINGPONG's feature mask and, as it is the only remaining bit,
drop the .features assignment completely.
Fixes: 62af6e1cb5 ("drm/msm/dpu: Add support for MSM8917")
Reported-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/640301/
Link: https://lore.kernel.org/r/20250301-dpu-fix-catalog-v2-2-498271be8b50@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The MSM8937 platform doesn't have DSC blocks nor does have it DSC
registers in the PINGPONG block. Drop the DPU_PINGPONG_DSC feature bit
from the PINGPONG's feature mask and, as it is the only remaining bit,
drop the .features assignment completely.
Fixes: c079680bb0 ("drm/msm/dpu: Add support for MSM8937")
Reported-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/640299/
Link: https://lore.kernel.org/r/20250301-dpu-fix-catalog-v2-1-498271be8b50@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
It is easy to skip or ignore the fact that the default SSPP feature
masks for SDM845+ don't include the SmartDMA bit (both during
development and during the review stage). Rename SSPP feature masks to
make it more explicit that using non-SmartDMA masks should not be an
exception rather than the rule.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/650425/
Link: https://lore.kernel.org/r/20250425-dpu-rework-vig-masks-v2-5-c71900687d08@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
