Pull SoC driver updates from Arnd Bergmann:
"Nothing particular important in the SoC driver updates, just the usual
improvements to for drivers/soc and a couple of subsystems that don't
fit anywhere else:
- The largest set of updates is for Qualcomm SoC drivers, extending
the set of supported features for additional SoCs in the QSEECOM,
LLCC and socinfo drivers.a
- The ti_sci firmware driver gains support for power managment
- The drivers/reset subsystem sees a rework of the microchip sparx5
and amlogic reset drivers to support additional chips, plus a few
minor updates on other platforms
- The SCMI firmware interface driver gains support for two protocol
extensions, allowing more flexible use of the shared memory area
and new DT binding properties for configurability.
- Mediatek SoC drivers gain support for power managment on the MT8188
SoC and a new driver for DVFS.
- The AMD/Xilinx ZynqMP SoC drivers gain support for system reboot
and a few bugfixes
- The Hisilicon Kunpeng HCCS driver gains support for configuring
lanes through sysfs
Finally, there are cleanups and minor fixes for drivers/{soc, bus,
memory}, including changing back the .remove_new callback to .remove,
as well as a few other updates for freescale (powerpc) soc drivers,
NXP i.MX soc drivers, cznic turris platform driver, memory controller
drviers, TI OMAP SoC drivers, and Tegra firmware drivers"
* tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (116 commits)
soc: fsl: cpm1: qmc: Set the ret error code on platform_get_irq() failure
soc: fsl: rcpm: fix missing of_node_put() in copy_ippdexpcr1_setting()
soc: fsl: cpm1: tsa: switch to for_each_available_child_of_node_scoped()
platform: cznic: turris-omnia-mcu: Rename variable holding GPIO line names
platform: cznic: turris-omnia-mcu: Document the driver private data structure
firmware: turris-mox-rwtm: Document the driver private data structure
bus: Switch back to struct platform_driver::remove()
soc: qcom: ice: Remove the device_link field in qcom_ice
drm/msm/adreno: Setup SMMU aparture for per-process page table
firmware: qcom: scm: Introduce CP_SMMU_APERTURE_ID
firmware: arm_scpi: Check the DVFS OPP count returned by the firmware
soc: qcom: socinfo: add IPQ5424/IPQ5404 SoC ID
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5424/IPQ5404
soc: qcom: llcc: Flip the manual slice configuration condition
dt-bindings: firmware: qcom,scm: Document sm8750 SCM
firmware: qcom: uefisecapp: Allow X1E Devkit devices
misc: lan966x_pci: Fix dtc warn 'Missing interrupt-parent'
misc: lan966x_pci: Fix dtc warns 'missing or empty reg/ranges property'
soc: qcom: llcc: Add LLCC configuration for the QCS8300 platform
dt-bindings: cache: qcom,llcc: Document the QCS8300 LLCC
...
A few more Qualcomm driver updates for v6.13
Make the Adreno driver invoke the SMMU aperture setup firmware function,
which is required to allow the GPU to manage per-process page tables in
some firmware versions - as an example Rb3Gen2 has no GPU without this.
Add X1E Devkit to the list of devices that has functional EFI variable
access through the uefisecapp.
Flip the "manual slice configuration quirk" in the Qualcomm LLCC driver,
as this only applies to a single platform, and introduce support for
QCS8300, QCS615, SAR2130P, and SAR1130P.
Lastly, add IPQ5424 and IPQ5404 to the Qualcomm socinfo driver.
* tag 'qcom-drivers-for-6.13-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: ice: Remove the device_link field in qcom_ice
drm/msm/adreno: Setup SMMU aparture for per-process page table
firmware: qcom: scm: Introduce CP_SMMU_APERTURE_ID
soc: qcom: socinfo: add IPQ5424/IPQ5404 SoC ID
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5424/IPQ5404
soc: qcom: llcc: Flip the manual slice configuration condition
dt-bindings: firmware: qcom,scm: Document sm8750 SCM
firmware: qcom: uefisecapp: Allow X1E Devkit devices
soc: qcom: llcc: Add LLCC configuration for the QCS8300 platform
dt-bindings: cache: qcom,llcc: Document the QCS8300 LLCC
soc: qcom: llcc: Add configuration data for QCS615
dt-bindings: cache: qcom,llcc: Document the QCS615 LLCC
soc: qcom: llcc: add support for SAR2130P and SAR1130P
soc: qcom: llcc: use deciman integers for bit shift values
dt-bindings: cache: qcom,llcc: document SAR2130P and SAR1130P
Link: https://lore.kernel.org/r/20241113032425.356306-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The struct device_link *link field in struct qcom_ice is only used to
store the result of a device_link_add call with the
DL_FLAG_AUTOREMOVE_SUPPLIER flag. With this flag, the resulting value
can only be used to check whether the link is present or not, as per the
device_link_add description, hence this commit removes the field.
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Link: https://lore.kernel.org/r/20241030025046.303342-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Commit c14e64b469 ("soc: qcom: llcc: Support chipsets that can write
to llcc") made the code not configure certain registers on SDM845 due
to firmware security policies. That turned out only to concern SDM845,
but the condition was chosen such that all other entries (for SoCs that
didnot need it) were required to set .need_llcc_cfg = true.
Flip the condition, so the default is "doesn't need the workaround".
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241104-topic-llcc_flip-v1-1-3003c846d131@oss.qualcomm.com
[bjorn: Dropped a few newly added need_llcc_cfg uses]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm driver updates for v6.13
Enable QSEECOM, and thereby access to EFI variables, for Lenovo Yoga
Slim 7x, Dell XPS 13, Microsoft Surface Pro 9.
Last Level Cache Controller (LLCC) driver code is shuffled, to improve
readability of the tables.
The Qualcomm socinfo driver gains support for QCS615, QCS9100, SAR1130P,
SAR2130P, and SA8255P.
A few drivers are simplified using dev_err_probe() and guard(), and a
few kernel-doc issues are corrected.
Mentioning of the #linux-msm IRC channel is added to the MAINTAINERS
file.
* tag 'qcom-drivers-for-6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (30 commits)
soc: qcom: socinfo: add QCS9100 ID
dt-bindings: arm: qcom,ids: add SoC ID for QCS9100
dt-bindings: soc: qcom,aoss-qmp: Document the QCS8300 AOSS channel
dt-bindings: soc: qcom: add qcom,qcs8300-imem compatible
dt-bindings: firmware: qcom,scm: document SCM on QCS8300 SoCs
soc: qcom: socinfo: add support for SA8255P
dt-bindings: arm: qcom: add the SoC ID for SA8255P
soc: qcom: smp2p: Simplify code with dev_err_probe()
soc: qcom: smem: Simplify code with dev_err_probe()
soc: qcom: rpmh-rsc: Simplify code with dev_err_probe()
dt-bindings: soc: qcom: aoss-qmp: document support for SA8255p
dt-bindings: firmware: qcom,scm: document support for SA8255p
dt-bindings: soc: qcom,aoss-qmp: Add SAR2130P compatible
dt-bindings: firmware: qcom,scm: Add SAR2130P compatible
soc: qcom: socinfo: add SoC IDs for SAR1130P and SAR2130P
dt-bindings: arm: qcom,ids: add SoC ID for SAR2130P and SAR1130P
dt-bindings: soc: qcom: aoss-qmp: Add SM8750
soc: qcom: socinfo: Add QCS615 SoC ID table entry
dt-bindings: arm: qcom,ids: add SoC ID for QCS615
soc: qcom: smem: Fix up kerneldoc
...
Link: https://lore.kernel.org/r/20241102231953.871067-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm driver fixes for v6.12
The Qualcomm EDAC driver's configuration of interrupts is made optional,
to avoid violating security constriants on X Elite platform .
The SCM drivers' detection mechanism for the presence of SHM bridge in QTEE,
is corrected to handle the case where firmware successfully returns that
the interface isn't supported.
The GLINK driver and the PMIC GLINK interface is updated to handle
buffer allocation issues during initialization of the communication
channel.
Allocation error handling in the socinfo dirver is corrected, and then
the fix is corrected.
* tag 'qcom-drivers-fixes-for-6.12' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: pmic_glink: Handle GLINK intent allocation rejections
rpmsg: glink: Handle rejected intent request better
soc: qcom: socinfo: fix revision check in qcom_socinfo_probe()
firmware: qcom: scm: Return -EOPNOTSUPP for unsupported SHM bridge enabling
EDAC/qcom: Make irq configuration optional
firmware: qcom: scm: fix a NULL-pointer dereference
firmware: qcom: scm: suppress download mode error
soc: qcom: Add check devm_kasprintf() returned value
MAINTAINERS: Qualcomm SoC: Match reserved-memory bindings
Link: https://lore.kernel.org/r/20241101161455.746290-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/soc to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
On the way do a few whitespace changes to make indention consistent.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Herve Codina <herve.codina@bootlin.com> # for fsl/qe/{qmc,tsa}.c
Acked-by: Bjorn Andersson <andersson@kernel.org> # qcom parts
Acked-by: Gabriel Somlo <gsomlo@gmail.com>
Acked-by: Andrew Jeffery <andrew@codeconstruct.com.au> # aspeed
Link: https://lore.kernel.org/r/20241029074859.509587-2-u.kleine-koenig@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some versions of the pmic_glink firmware does not allow dynamic GLINK
intent allocations, attempting to send a message before the firmware has
allocated its receive buffers and announced these intent allocations
will fail. When this happens something like this showns up in the log:
pmic_glink_altmode.pmic_glink_altmode pmic_glink.altmode.0: failed to send altmode request: 0x10 (-125)
pmic_glink_altmode.pmic_glink_altmode pmic_glink.altmode.0: failed to request altmode notifications: -125
ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: failed to send UCSI read request: -125
qcom_battmgr.pmic_glink_power_supply pmic_glink.power-supply.0: failed to request power notifications
GLINK has been updated to distinguish between the cases where the remote
is going down (-ECANCELED) and the intent allocation being rejected
(-EAGAIN).
Retry the send until intent buffers becomes available, or an actual
error occur.
To avoid infinitely waiting for the firmware in the event that this
misbehaves and no intents arrive, an arbitrary 5 second timeout is
used.
This patch was developed with input from Chris Lew.
Reported-by: Johan Hovold <johan@kernel.org>
Closes: https://lore.kernel.org/all/Zqet8iInnDhnxkT9@hovoldconsulting.com/#t
Cc: stable@vger.kernel.org # rpmsg: glink: Handle rejected intent request better
Fixes: 58ef4ece1e ("soc: qcom: pmic_glink: Introduce base PMIC GLINK driver")
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Reviewed-by: Chris Lew <quic_clew@quicinc.com>
Link: https://lore.kernel.org/r/20241023-pmic-glink-ecancelled-v2-2-ebc268129407@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In success case, the revision holds a non-null pointer. The current
logic incorrectly returns an error for a non-null pointer, whereas
it should return an error for a null pointer.
The socinfo driver for IPQ9574 and IPQ5332 is currently broken,
resulting in the following error message
qcom-socinfo qcom-socinfo: probe with driver qcom-socinfo failed with
error -12
Add a null check for the revision to ensure it returns an error only in
failure case (null pointer).
Fixes: e694d2b5c5 ("soc: qcom: Add check devm_kasprintf() returned value")
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241016144852.2888679-1-quic_mmanikan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This loop is supposed to break if the frequency returned from
clk_round_rate() is the same as on the previous iteration. However,
that check doesn't make sense on the first iteration through the loop.
It leads to reading before the start of these->clk_perf_tbl[] array.
Fixes: eddac5af06 ("soc: qcom: Add GENI based QUP Wrapper driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/8cd12678-f44a-4b16-a579-c8f11175ee8c@stanley.mountain
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On most modern qualcomm SoCs, the configuration necessary to enable the
Tag/Data RAM related irqs being propagated to the SoC irq controller is
already done in firmware (in DSF or 'DDR System Firmware')
On some like the x1e80100, these registers aren't even accesible to the
kernel causing a crash when edac device is probed.
Hence, make the irq configuration optional in the driver and mark x1e80100
as the SoC on which this should be avoided.
Fixes: af16b00578 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Reported-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240903101510.3452734-1-quic_rjendra@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Pull SoC driver updates from Arnd Bergmann:
"The driver updates seem larger this time around, with changes is many
of the SoC specific drivers, both the custom drivers/soc ones and the
closely related subsystems (memory, bus, firmware, reset, ...).
The at91 platform gains support for sam9x7 chips in the soc and power
management code. This is the latest variant of one of the oldest still
supported SoC families, using the ARM9 (ARMv5) core.
As usual, the qualcomm snapdragon platform gets a ton of updates in
many of their drivers to add more features and additional SoC support.
Most of these are somewhat firmware related as the platform has a
number of firmware based interfaces to the kernel. A notable addition
here is the inclusion of trace events to two of these drivers.
Herve Codina and Christophe Leroy are now sending updates for
drivers/soc/fsl/ code through the SoC tree, this contains both PowerPC
and Arm specific platforms and has previously been problematic to
maintain. The first update here contains support for newer PowerPC
variants and some cleanups.
The turris mox firmware driver has a number of updates, mostly
cleanups.
The Arm SCMI firmware driver gets a major rework to modularize the
existing code into separately loadable drivers for the various
transports, the addition of custom NXP i.MX9 interfaces and a number
of smaller updates.
The Arm FF-A firmware driver gets a feature update to support the v1.2
version of the specification.
The reset controller drivers have some smaller cleanups and a newly
added driver for the Intel/Mobileye EyeQ5/EyeQ6 MIPS SoCs.
The memory controller drivers get some cleanups and refactoring for
Tegra, TI, Freescale/NXP and a couple more platforms.
Finally there are lots of minor updates to firmware (raspberry pi,
tegra, imx), bus (sunxi, omap, tegra) and soc (rockchips, tegra,
amlogic, mediatek) drivers and their DT bindings"
* tag 'soc-drivers-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (212 commits)
firmware: imx: remove duplicate scmi_imx_misc_ctrl_get()
platform: cznic: turris-omnia-mcu: Fix error check in omnia_mcu_register_trng()
bus: sunxi-rsb: Simplify code with dev_err_probe()
soc: fsl: qe: ucc: Export ucc_mux_set_grant_tsa_bkpt
soc: fsl: cpm1: qmc: Fix dependency on fsl_soc.h
dt-bindings: arm: rockchip: Add rk3576 compatible string to pmu.yaml
soc: fsl: qbman: Remove redundant warnings
soc: fsl: qbman: Use iommu_paging_domain_alloc()
MAINTAINERS: Add QE files related to the Freescale QMC controller
soc: fsl: cpm1: qmc: Handle QUICC Engine (QE) soft-qmc firmware
soc: fsl: cpm1: qmc: Add support for QUICC Engine (QE) implementation
soc: fsl: qe: Add missing PUSHSCHED command
soc: fsl: qe: Add resource-managed muram allocators
soc: fsl: cpm1: qmc: Introduce qmc_version
soc: fsl: cpm1: qmc: Rename SCC_GSMRL_MODE_QMC
soc: fsl: cpm1: qmc: Handle RPACK initialization
soc: fsl: cpm1: qmc: Rename qmc_chan_command()
soc: fsl: cpm1: qmc: Introduce qmc_{init,exit}_xcc() and their CPM1 version
soc: fsl: cpm1: qmc: Introduce qmc_init_resource() and its CPM1 version
soc: fsl: cpm1: qmc: Re-order probe() operations
...
The Qualcomm pd-mapper is a refcounted singleton, but the refcount is
never incremented, which means the as soon as any remoteproc instance
stops the count will hit 0.
At this point the pd-mapper QMI service is stopped, leaving firmware
without access to the PD information. Stopping any other remoteproc
instances will result in a use-after-free, which best case manifest
itself as a refcount underflow:
refcount_t: underflow; use-after-free.
WARNING: CPU: 1 PID: 354 at lib/refcount.c:87 refcount_dec_and_mutex_lock+0xc4/0x148
...
Call trace:
refcount_dec_and_mutex_lock+0xc4/0x148
qcom_pdm_remove+0x40/0x118 [qcom_pd_mapper]
...
Fix this by incrementing the refcount, so that the pd-mapper is only
torn down when the last remoteproc stops, as intended.
Fixes: 1ebcde047c ("soc: qcom: add pd-mapper implementation")
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240820-pd-mapper-refcount-fix-v1-1-03ea65c0309b@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Commit '9329933699b3 ("soc: qcom: pmic_glink: Make client-lock
non-sleeping")' moved the pmic_glink client list under a spinlock, as it
is accessed by the rpmsg/glink callback, which in turn is invoked from
IRQ context.
This means that ucsi_unregister() is now called from atomic context,
which isn't feasible as it's expecting a sleepable context. An effort is
under way to get GLINK to invoke its callbacks in a sleepable context,
but until then lets schedule the unregistration.
A side effect of this is that ucsi_unregister() can now happen
after the remote processor, and thereby the communication link with it, is
gone. pmic_glink_send() is amended with a check to avoid the resulting NULL
pointer dereference.
This does however result in the user being informed about this error by
the following entry in the kernel log:
ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: failed to send UCSI write request: -5
Fixes: 9329933699 ("soc: qcom: pmic_glink: Make client-lock non-sleeping")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240820-pmic-glink-v6-11-races-v3-2-eec53c750a04@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
