For hs400(es) mode, the 'hs400-ds-delay' is typically configured in the
dts. However, some projects may only define 'mediatek,hs400-ds-dly3',
which can lead to initialization failures in hs400es mode. CMD13 reported
response crc error in the mmc_switch_status() just after switching to
hs400es mode.
[ 1.914038][ T82] mmc0: mmc_select_hs400es failed, error -84
[ 1.914954][ T82] mmc0: error -84 whilst initialising MMC card
Currently, the hs400_ds_dly3 value is set within the tuning function. This
means that the PAD_DS_DLY3 field is not configured before tuning process,
which is the reason for the above-mentioned CMD13 response crc error.
Move the PAD_DS_DLY3 field configuration into msdc_prepare_hs400_tuning(),
and add a value check of hs400_ds_delay to prevent overwriting by zero when
the 'hs400-ds-delay' is not set in the dts. In addition, since hs400(es)
only tune the PAD_DS_DLY1, the PAD_DS_DLY2_SEL bit should be cleared to
bypass it.
Fixes: c4ac38c653 ("mmc: mtk-sd: Add HS400 online tuning support")
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250123092644.7359-1-andy-ld.lu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 941a7abd46.
This commit uses presence of device-tree properties vmmc-supply and
vqmmc-supply for deciding whether to enable a quirk affecting timing of
clock and data.
The intention was to address issues observed with eMMC and SD on AM62
platforms.
This new quirk is however also enabled for AM64 breaking microSD access
on the SolidRun HimmingBoard-T which is supported in-tree since v6.11,
causing a regression. During boot microSD initialization now fails with
the error below:
[ 2.008520] mmc1: SDHCI controller on fa00000.mmc [fa00000.mmc] using ADMA 64-bit
[ 2.115348] mmc1: error -110 whilst initialising SD card
The heuristics for enabling the quirk are clearly not correct as they
break at least one but potentially many existing boards.
Revert the change and restore original behaviour until a more
appropriate method of selecting the quirk is derived.
Fixes: 941a7abd46 ("mmc: sdhci_am654: Add sdhci_am654_start_signal_voltage_switch")
Closes: https://lore.kernel.org/linux-mmc/a70fc9fc-186f-4165-a652-3de50733763a@solid-run.com/
Cc: stable@vger.kernel.org
Signed-off-by: Josua Mayer <josua@solid-run.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250127-am654-mmc-regression-v2-1-9bb39fb12810@solid-run.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Qualcomm regulator supports two power supply modes: HPM and LPM.
Currently, the sdhci-msm.c driver does not set the load to adjust
the current for eMMC and SD. If the regulator dont't set correct
load in LPM state, it will lead to the inability to properly
initialize eMMC and SD.
Set the correct regulator current for eMMC and SD to ensure that the
device can work normally even when the regulator is in LPM.
Signed-off-by: Yuanjie Yang <quic_yuanjiey@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250114083514.258379-1-quic_yuanjiey@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/all/20250111185410.183896-1-krzysztof.kozlowski@linaro.org>/
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/all/20250109155255.3438450-1-robh@kernel.org/
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As is being done in ufs-qcom, make the sdhci-msm driver override the
full crypto profile rather than "just" key programming and eviction.
This makes it much more straightforward to add support for
hardware-wrapped inline encryption keys. It also makes it easy to pass
the original blk_crypto_key down to qcom_ice_program_key() once it is
updated to require the key in that form.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Message-ID: <20241213041958.202565-8-ebiggers@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a helper function that encapsulates a container_of expression. For
now there is just one user but soon there will be more.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Message-ID: <20241213041958.202565-7-ebiggers@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.13-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.14.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit c7eed31e23 ("mmc: sdhci-msm: Switch to the new ICE API")
introduced an incorrect check of the algorithm ID into the key eviction
path, and thus qcom_ice_evict_key() is no longer ever called. Fix it.
Fixes: c7eed31e23 ("mmc: sdhci-msm: Switch to the new ICE API")
Cc: stable@vger.kernel.org
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Message-ID: <20241213041958.202565-6-ebiggers@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the mtk-sd driver tries to get and map the second register
base, named top_base in the code, regardless of whether the SoC model
actually has it or not. This produces confusing big error messages on
the platforms that don't need it:
mtk-msdc 11260000.mmc: error -EINVAL: invalid resource (null)
Limit it to the platforms that actually require it, based on their
device tree entries, and properly fail if it is missing.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <20241210073212.3917912-3-wenst@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The struct resource is not used for anything else, so we can simplify
the code a bit by using the helper function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241101101441.3518612-5-andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
First of all, this error message is just informative and doesn't prevent
driver from going on. Second, the ioremap() on many architectures just
works on page size granularity, which is higher than 256 bytes. Last,
but not lease, this is an impediment for furhter cleanups, hence remove
it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241101101441.3518612-4-andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.13-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.14.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current implementation leaves pdev->dev as a wakeup source. Add a
device_init_wakeup(&pdev->dev, false) call in the .remove() function and
in the error path of the .probe() function.
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Fixes: 527f36f5ef ("mmc: mediatek: add support for SDIO eint wakup IRQ")
Cc: stable@vger.kernel.org
Message-ID: <20241203023442.2434018-1-joe@pf.is.s.u-tokyo.ac.jp>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Value 0 in ADMA length descriptor is interpreted as 65536 on new Tegra
chips, remove SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC quirk to make sure max
ADMA2 length is 65536.
Fixes: 4346b7c794 ("mmc: tegra: Add Tegra186 support")
Cc: stable@vger.kernel.org
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241209101009.22710-1-pshete@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current process flow does not handle MMC requests that are indicated
to ignore the command response CRC. For instance, cmd12 and cmd48 from
mmc_cqe_recovery() are marked to ignore CRC, but they are not matched to
the appropriate response type in msdc_cmd_find_resp(). As a result, they
are defaulted to 'MMC_RSP_NONE', which means no response is expected.
This commit applies the flag 'MMC_RSP_R1B_NO_CRC' to fix the response type
setting in msdc_cmd_find_resp() and adds the logic to ignore CRC in
msdc_cmd_done().
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Message-ID: <20241126125041.16071-3-andy-ld.lu@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC_RSP_R1_NO_CRC type of response is not being used by the mmc core
for any commands. Let's therefore drop it, together with the corresponding
code in the host drivers.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # for TMIO
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Message-ID: <20241125132311.23939-1-ulf.hansson@linaro.org>
Enable SDHCI_QUIRK_NO_LED quirk for S32G2/S32G3 variants as the controller
does not have a LED signal line.
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Message-ID: <20241125083357.1041949-1-ciprianmarian.costea@oss.nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Vexia Edu Atla 10 tablet distributed to schools in the Spanish
Andalucía region has no ACPI fwnode associated with the SDHCI controller
for its microsd-slot and thus has no ACPI GPIO resource info.
This causes the following error to be logged and the slot to not work:
[ 10.572113] sdhci-pci 0000:00:12.0: failed to setup card detect gpio
Add a DMI quirk table for providing gpiod_lookup_tables with manually
provided CD GPIO info and use this DMI table to provide the CD GPIO info
on this tablet. This fixes the microsd-slot not working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Message-ID: <20241118210049.311079-1-hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.12-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.13.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 8396c793ff ("mmc: dw_mmc: Fix IDMAC operation with pages
bigger than 4K") increased the max_req_size, even for 4K pages, causing
various issues:
- Panic booting the kernel/rootfs from an SD card on Rockchip RK3566
- Panic booting the kernel/rootfs from an SD card on StarFive JH7100
- "swiotlb buffer is full" and data corruption on StarFive JH7110
At this stage no fix have been found, so it's probably better to just
revert the change.
This reverts commit 8396c793ff.
Cc: stable@vger.kernel.org
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Fixes: 8396c793ff ("mmc: dw_mmc: Fix IDMAC operation with pages bigger than 4K")
Closes: https://lore.kernel.org/linux-mmc/614692b4-1dbe-31b8-a34d-cb6db1909bb7@w6rz.net/
Closes: https://lore.kernel.org/linux-mmc/CAC8uq=Ppnmv98mpa1CrWLawWoPnu5abtU69v-=G-P7ysATQ2Pw@mail.gmail.com/
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-ID: <20241110114700.622372-1-aurelien@aurel32.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the MMC_CAP2_CRYPTO flag is set by default for eMMC hosts.
However, this flag should not be set for hosts that do not support inline
encryption.
The 'crypto' clock, as described in the documentation, is used for data
encryption and decryption. Therefore, only hosts that are configured with
this 'crypto' clock should have the MMC_CAP2_CRYPTO flag set.
Fixes: 7b438d0377 ("mmc: mtk-sd: add Inline Crypto Engine clock control")
Fixes: ed299eda8f ("mmc: mtk-sd: fix devm_clk_get_optional usage")
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Cc: stable@vger.kernel.org
Message-ID: <20241111085039.26527-1-andy-ld.lu@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the probe function, it goes to 'release_mem' label and returns after
some procedure failure. But if the clocks (partial or all) have been
enabled previously, they would not be disabled in msdc_runtime_suspend,
since runtime PM is not yet enabled for this case.
That cause mmc related clocks always on during system suspend and block
suspend flow. Below log is from a SDCard issue of MT8196 chromebook, it
returns -ETIMEOUT while polling clock stable in the msdc_ungate_clock()
and probe failed, but the enabled clocks could not be disabled anyway.
[ 129.059253] clk_chk_dev_pm_suspend()
[ 129.350119] suspend warning: msdcpll is on
[ 129.354494] [ck_msdc30_1_sel : enabled, 1, 1, 191999939, ck_msdcpll_d2]
[ 129.362787] [ck_msdcpll_d2 : enabled, 1, 1, 191999939, msdcpll]
[ 129.371041] [ck_msdc30_1_ck : enabled, 1, 1, 191999939, ck_msdc30_1_sel]
[ 129.379295] [msdcpll : enabled, 1, 1, 383999878, clk26m]
Add a new 'release_clk' label and reorder the error handle functions to
make sure the clocks be disabled after probe failure.
Fixes: ffaea6ebfe ("mmc: mtk-sd: Use readl_poll_timeout instead of open-coded polling")
Fixes: 7a2fa8eed9 ("mmc: mtk-sd: use devm_mmc_alloc_host")
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable@vger.kernel.org
Message-ID: <20241107121215.5201-1-andy-ld.lu@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It turns out that the Allwinner A100/A133 SoC only supports 8K DMA
blocks (13 bits wide), for both the SD/SDIO and eMMC instances.
And while this alone would make a trivial fix, the H616 falls back to
the A100 compatible string, so we have to now match the H616 compatible
string explicitly against the description advertising 64K DMA blocks.
As the A100 is now compatible with the D1 description, let the A100
compatible string point to that block instead, and introduce an explicit
match against the H616 string, pointing to the old description.
Also remove the redundant setting of clk_delays to NULL on the way.
Fixes: 3536b82e58 ("mmc: sunxi: add support for A100 mmc controller")
Cc: stable@vger.kernel.org
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Parthiban Nallathambi <parthiban@linumiz.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Message-ID: <20241107014240.24669-1-andre.przywara@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
NXP ESDHC supports setting data timeout using uSDHCx_SYS_CTRL register
DTOCV bits (bits 16-19).
Currently the driver accesses those bits by 32-bit write using
SDHCI_TIMEOUT_CONTROL (0x2E) defined in drivers/mmc/host/sdhci.h.
This is offset by two bytes relative to uSDHCx_SYS_CTRL (0x2C).
The driver also defines ESDHC_SYS_CTRL_DTOCV_MASK as first 4 bits, which
is correct relative to SDHCI_TIMEOUT_CONTROL but not relative to
uSDHCx_SYS_CTRL. The definition carrying control register in its name is
therefore inconsistent.
Update the bitmask definition for bits 16-19 to be correct relative to
control register base.
Update the esdhc_set_timeout function to set timeout value at control
register base, not timeout offset.
This solves a purely cosmetic problem.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241101-imx-emmc-reset-v3-2-184965eed476@solid-run.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
NXP ESDHC supports control of native emmc reset signal when pinmux is
set accordingly, using uSDHCx_SYS_CTRL register IPP_RST_N bit.
Documentation is available in NXP i.MX6Q Reference Manual.
Implement the hw_reset function in sdhci_ops asserting reset for at
least 1us and waiting at least 200us after deassertion.
Lower bounds are based on:
JEDEC Standard No. 84-B51, 6.15.10 H/W Reset Operation, page 159.
Upper bounds are chosen allowing flexibility to the scheduler.
Tested on SolidRun i.MX8DXL SoM with a scope, and confirmed that eMMC is
still accessible after boot:
- eMMC extcsd has RST_N_FUNCTION=0x01
- sdhc node has cap-mmc-hw-reset
- pinmux set for EMMC0_RESET_B
- Linux v5.15
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241101-imx-emmc-reset-v3-1-184965eed476@solid-run.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a type issue in the argument in the uhs2_dev_cmd()
that will generate a warning when building the kernel.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410260525.ZUuPhMJz-lkp@intel.com/
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Message-ID: <20241101104416.4954-1-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are unnecessary variables in the sdhci_uhs2_send_command() that will
generate a warning when building the kernel. Let's drop them!
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410252107.y9EgrTbA-lkp@intel.com/
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241030112216.4057-2-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a type issue in the argument in the __sdhci_uhs2_send_command()
that will generate a warning when building the kernel.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410260525.ZUuPhMJz-lkp@intel.com/
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Message-ID: <20241030112216.4057-1-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no need to ask the user about enabling UHS-II support, as all
drivers that support UHS2-capable devices already select MMC_SDHCI_UHS2.
Hence make the symbol invisible, unless when compile-testing.
Fixes: 2af7dd8b64 ("mmc: sdhci: add UHS-II module and add a kernel configuration")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Message-ID: <079f2b7473d34895843ad278d79930c681385b2e.1730282633.git.geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The host->ops pointer can't be NULL in sdhci_uhs2_do_detect_init(). Let's
drop the redundant check.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202410271835.tqz9s9JV-lkp@intel.com/
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241030015326.2289070-1-benchuanggli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The custom sdhost controller on BCM2835 is feed by the critical VPU clock.
In preparation for PM suspend/resume support, add a proper clock handling
to the driver like in the other clock consumers (e.g. I2C).
Move the clock handling behind mmc_of_parse(), because it could return
with -EPROBE_DEFER and we want to minimize potential clock operation during
boot phase.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Message-ID: <20241025103621.4780-5-wahrenst@gmx.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The type of mmc_ios.clock is unsigned int, so the cached value
should be of the same type.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Message-ID: <20241025103621.4780-4-wahrenst@gmx.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.12-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.13.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When starting the SD Express process, the low power negotiation mode will
be disabled, so we need to re-enable it after switching back to SD mode.
Fixes: 0e92aec2ef ("mmc: sdhci-pci-gli: Add support SD Express card for GL9767")
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Cc: stable@vger.kernel.org
Message-ID: <20241025060017.1663697-2-benchuanggli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On sdhci_gl9767_set_clock(), the vendor header space(VHS) is read-only
after calling gl9767_disable_ssc_pll() and gl9767_set_ssc_pll_205mhz().
So the low power negotiation mode cannot be enabled again.
Introduce gl9767_set_low_power_negotiation() function to fix it.
The explanation process is as below.
static void sdhci_gl9767_set_clock()
{
...
gl9767_vhs_write();
...
value |= PCIE_GLI_9767_CFG_LOW_PWR_OFF;
pci_write_config_dword(pdev, PCIE_GLI_9767_CFG, value); <--- (a)
gl9767_disable_ssc_pll(); <--- (b)
sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
if (clock == 0)
return; <-- (I)
...
if (clock == 200000000 && ios->timing == MMC_TIMING_UHS_SDR104) {
...
gl9767_set_ssc_pll_205mhz(); <--- (c)
}
...
value &= ~PCIE_GLI_9767_CFG_LOW_PWR_OFF;
pci_write_config_dword(pdev, PCIE_GLI_9767_CFG, value); <-- (II)
gl9767_vhs_read();
}
(a) disable low power negotiation mode. When return on (I), the low power
mode is disabled. After (b) and (c), VHS is read-only, the low power mode
cannot be enabled on (II).
Reported-by: Georg Gottleuber <ggo@tuxedocomputers.com>
Fixes: d275435551 ("mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL9767")
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Tested-by: Georg Gottleuber <ggo@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Message-ID: <20241025060017.1663697-1-benchuanggli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for mmc on MT7988 SoC.
We can use mt7986 platform data in driver, but mt7988 needs different
clocks so for binding we need own compatible.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <20241012143826.7690-3-linux@fw-web.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Mediatek SoC MT8196 features a new design for tx/rx path. The new tx
path incorporates register settings that are closely associated with
bus timing. And the difference between new rx path and older versions
is the usage of distinct register bits when setting the data sampling
edge as part of the tuning process.
Besides, the register settings for STOP_DLY_SEL and POP_EN_CNT are
different from previous SoCs.
For the changes mentioned in relation to the MT8196, the new compatible
string 'mediatek,mt8196-mmc' is introduced. This is to accommodate
different settings and workflows specific to the MT8196.
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <20241011024906.8173-3-andy-ld.lu@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are modified register settings for STOP_DLY_SEL and POP_EN_CNT
from our next generation SoCs, due to the advanced chip manufacturing
process and the resulting changes in the internal signal timing.
Add two new fields to the compatibility structure to reflect the
modifications. For legacy SoCs, also add the original value of
'stop_dly_sel' to the platform data, for unified code setting.
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <20241011024906.8173-2-andy-ld.lu@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Changes are:
* Enable the internal clock when do reset on UHS-II mode.
* Increase timeout value before detecting UHS-II interface.
* Add vendor settings for UHS-II mode.
* Use the function sdhci_gli_wait_software_reset_done() for gl9767 reset.
* Remove unnecessary code from sdhci_gl9767_reset().
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Signed-off-by: Lucas Lai <lucas.lai@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-17-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Changes are:
* Disable GL9755 overcurrent interrupt when power on/off on UHS-II.
* Enable the internal clock when do reset on UHS-II mode.
* Increase timeout value before detecting UHS-II interface.
* Add vendor settings fro UHS-II mode.
* Remove sdhci_gli_enable_internal_clock functon unused clk_ctrl variable.
* Make a function sdhci_gli_wait_software_reset_done() for gl9755 reset.
* Remove unnecessary code from sdhci_gl9755_reset().
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Signed-off-by: Lucas Lai <lucas.lai@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-16-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch prepares for adding UHS-II support at a specific UHS-II
capable sdhci-pci controller, GL9755 for now.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-15-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This "pre" hook for detect_init(), uhs2_pre_detect_init, will be required
to enable UHS-II support, at least, on GL9755.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-14-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is a sdhci version of mmc's request operation.
It covers both UHS-I and UHS-II.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-13-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is a UHS-II version of sdhci's request() operation.
It handles UHS-II related command interrupts and errors.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-12-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
UHS-II interface (related registers) will be initialized here. The
operations include mmc's uhs2_set_reg operations, mmc's uhs2_detect_init
operations, uhs2_[enable|disable]_clk operations. After detected the UHS-II
interface, the host's UHS-II capabilities will be set up here and
interrupts will also be enabled.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-11-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is a sdhci version of mmc's set_ios operation.
This is used to handle basic IO bus setting.
It covers both UHS-I and UHS-II.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-10-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is a UHS-II version of sdhci's add_host/remove_host operation.
Any sdhci drivers which are capable of handling UHS-II cards must
call those functions instead of the corresponding sdhci's.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-9-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is a UHS-II version of sdhci's set_timeout() operation.
Use sdhci_uhs2_set_timeout() to set and calculate the timeout time.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-8-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
