mvs_phys_reset() was added in 2009's commit 20b09c2992 ("[SCSI] mvsas:
add support for 94xx; layout change; bug fixes") but hasn't been used.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20250127002601.113555-1-linux@treblig.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A null dereference or oops exception will eventually occur when qla1280.c
driver is compiled with DEBUG_QLA1280 enabled and ql_debug_level > 2. I
think its clear from the code that the intention here is sg_dma_len(s) not
length of sg_next(s) when printing the debug info.
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20250125095033.26188-1-linmag7@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kai Mäkisara <Kai.Makisara@kolumbus.fi> says:
The first patch re-applies after device reset some settings changed
by the user (partition, density, block size).
The second and third patch address the case where more than one ULD
access the same device. The Unit Attention (UA) sense data is sent only
to one ULD and the others miss it. The st driver needs to find out
if device reset or media change has happened.
The second patch adds counters for New Media and Power On/Reset (POR)
Unit Attentions to the scsi_device struct. The third one changes st
so that these are used: if the value in the scsi_device struct does
not match the one stored locally, the corresponding UA has happened.
Use of the was_reset flag has been removed.
The fourth patch adds a file to sysfs to tell the user if reads/writes
to a tape are blocked following a device reset.
Link: https://lore.kernel.org/r/20250120194925.44432-1-Kai.Makisara@kolumbus.fi
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the value read from the file is 1, reads and writes from/to the device
are blocked because the tape position may not match user's expectation
(tape rewound after device reset).
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://lore.kernel.org/r/20250201151106.25529-1-Kai.Makisara@kolumbus.fi
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Tested-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Compare the stored values of por_ctr and new_media_ctr against the values
in the device struct. In case of mismatch, the Unit Attention corresponding
to the counter has happened. This is a safeguard against another ULD
catching the Unit Attention sense data.
Macros scsi_get_ua_new_media_ctr and scsi_get_ua_por_ctr are added to read
the current values of the counters.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://lore.kernel.org/r/20250120194925.44432-4-Kai.Makisara@kolumbus.fi
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Tested-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The purpose of the counters is to enable all ULDs attached to a device to
find out that a New Media or/and Power On/Reset Unit Attentions has/have
been set, even if another ULD catches the Unit Attention as response to a
SCSI command.
The ULDs can read the counters and see if the values have changed from the
previous check.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://lore.kernel.org/r/20250120194925.44432-3-Kai.Makisara@kolumbus.fi
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Tested-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some of the allowed operations put the tape into a known position to
continue operation assuming only the tape position has changed. But reset
sets partition, density and block size to drive default values. These
should be restored to the values before reset.
Normally the current block size and density are stored by the drive. If
the settings have been changed, the changed values have to be saved by the
driver across reset.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://lore.kernel.org/r/20250120194925.44432-2-Kai.Makisara@kolumbus.fi
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Tested-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'struct pci_error_handlers' are not modified in these drivers.
Constifying these structures moves some data to a read-only section, so
increase overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
39049 6429 112 45590 b216 drivers/scsi/aacraid/linit.o
After:
=====
text data bss dec hex filename
39113 6365 112 45590 b216 drivers/scsi/aacraid/linit.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/efdec8425981e10fc398fa2ac599c9c45d930561.1737318548.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In StorVSC, payload->range.len is used to indicate if this SCSI command
carries payload. This data is allocated as part of the private driver data
by the upper layer and may get passed to lower driver uninitialized.
For example, the SCSI error handling mid layer may send TEST_UNIT_READY or
REQUEST_SENSE while reusing the buffer from a failed command. The private
data section may have stale data from the previous command.
If the SCSI command doesn't carry payload, the driver may use this value as
is for communicating with host, resulting in possible corruption.
Fix this by always initializing this value.
Fixes: be0cf6ca30 ("scsi: storvsc: Set the tablesize based on the information given by the host")
Cc: stable@kernel.org
Tested-by: Roman Kisel <romank@linux.microsoft.com>
Reviewed-by: Roman Kisel <romank@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Long Li <longli@microsoft.com>
Link: https://lore.kernel.org/r/1737601642-7759-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fail I/Os instead of retry to prevent user space processes from being
blocked on the I/O completion for several minutes.
Retrying I/Os during "depopulation in progress" or "depopulation restore in
progress" results in a continuous retry loop until the depopulation
completes or until the I/O retry loop is aborted due to a timeout by the
scsi_cmd_runtime_exceeced().
Depopulation is slow and can take 24+ hours to complete on 20+ TB HDDs.
Most I/Os in the depopulation retry loop end up taking several minutes
before returning the failure to user space.
Cc: stable@vger.kernel.org # 4.18.x: 2bbeb8d scsi: core: Handle depopulation and restoration in progress
Cc: stable@vger.kernel.org # 4.18.x
Fixes: e37c7d9a03 ("scsi: core: sanitize++ in progress")
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20250131184408.859579-1-ipylypiv@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Filesystems can write to disk from page reclaim with __GFP_FS
set. Marc found a case where scsi_realloc_sdev_budget_map() ends up in
page reclaim with GFP_KERNEL, where it could try to take filesystem
locks again, leading to a deadlock.
WARNING: possible circular locking dependency detected
6.13.0 #1 Not tainted
------------------------------------------------------
kswapd0/70 is trying to acquire lock:
ffff8881025d5d78 (&q->q_usage_counter(io)){++++}-{0:0}, at: blk_mq_submit_bio+0x461/0x6e0
but task is already holding lock:
ffffffff81ef5f40 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat+0x9f/0x760
The full lockdep splat can be found in Marc's report:
https://lkml.org/lkml/2025/1/24/1101
Avoid the potential deadlock by doing the allocation with GFP_NOIO, which
prevents both filesystem and block layer recursion.
Reported-by: Marc Aurèle La France <tsi@tuyoix.net>
Signed-off-by: Rik van Riel <riel@surriel.com>
Link: https://lore.kernel.org/r/20250129104525.0ae8421e@fangorn
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----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=molg
-----END PGP SIGNATURE-----
Merge tag 'block-6.14-20250131' of git://git.kernel.dk/linux
Pull more block updates from Jens Axboe:
- MD pull request via Song:
- Fix a md-cluster regression introduced
- More sysfs race fixes
- Mark anything inside queue freezing as not being able to do IO for
memory allocations
- Fix for a regression introduced in loop in this merge window
- Fix for a regression in queue mapping setups introduced in this merge
window
- Fix for the block dio fops attempting an iov_iter revert upton
getting -EIOCBQUEUED on the read side. This one is going to stable as
well
* tag 'block-6.14-20250131' of git://git.kernel.dk/linux:
block: force noio scope in blk_mq_freeze_queue
block: fix nr_hw_queue update racing with disk addition/removal
block: get rid of request queue ->sysfs_dir_lock
loop: don't clear LO_FLAGS_PARTSCAN on LOOP_SET_STATUS{,64}
md/md-bitmap: Synchronize bitmap_get_stats() with bitmap lifetime
blk-mq: create correct map for fallback case
block: don't revert iter for -EIOCBQUEUED
When block drivers or the core block code perform allocations with a
frozen queue, this could try to recurse into the block device to
reclaim memory and deadlock. Thus all allocations done by a process
that froze a queue need to be done without __GFP_IO and __GFP_FS.
Instead of tying to track all of them down, force a noio scope as
part of freezing the queue.
Note that nvme is a bit of a mess here due to the non-owner freezes,
and they will be addressed separately.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20250131120352.1315351-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All ctl_table declared outside of functions and that remain unmodified after
initialization are const qualified. This prevents unintended modifications to
proc_handler function pointers by placing them in the .rodata section. This is
a continuation of the tree-wide effort started a few releases ago with the
constification of the ctl_table struct arguments in the sysctl API done in
78eb4ea25c ("sysctl: treewide: constify the ctl_table argument of
proc_handlers")
Testing:
Testing was done on 0-day and sysctl selftests in x86_64. The linux-next
branch was not used for such a big change in order to avoid unnecessary merge
conflicts
-----BEGIN PGP SIGNATURE-----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=x7aW
-----END PGP SIGNATURE-----
Merge tag 'constfy-sysctl-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/sysctl/sysctl
Pull sysctl table constification from Joel Granados:
"All ctl_table declared outside of functions and that remain unmodified
after initialization are const qualified.
This prevents unintended modifications to proc_handler function
pointers by placing them in the .rodata section.
This is a continuation of the tree-wide effort started a few releases
ago with the constification of the ctl_table struct arguments in the
sysctl API done in 78eb4ea25c ("sysctl: treewide: constify the
ctl_table argument of proc_handlers")"
* tag 'constfy-sysctl-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/sysctl/sysctl:
treewide: const qualify ctl_tables where applicable
Here is the big set of driver core and debugfs updates for 6.14-rc1.
It's coming late in the merge cycle as there are a number of merge
conflicts with your tree now, and I wanted to make sure they were
working properly. To resolve them, look in linux-next, and I will send
the "fixup" patch as a response to the pull request.
Included in here is a bunch of driver core, PCI, OF, and platform rust
bindings (all acked by the different subsystem maintainers), hence the
merge conflict with the rust tree, and some driver core api updates to
mark things as const, which will also require some fixups due to new
stuff coming in through other trees in this merge window.
There are also a bunch of debugfs updates from Al, and there is at least
one user that does have a regression with these, but Al is working on
tracking down the fix for it. In my use (and everyone else's linux-next
use), it does not seem like a big issue at the moment.
Here's a short list of the things in here:
- driver core bindings for PCI, platform, OF, and some i/o functions.
We are almost at the "write a real driver in rust" stage now,
depending on what you want to do.
- misc device rust bindings and a sample driver to show how to use
them
- debugfs cleanups in the fs as well as the users of the fs api for
places where drivers got it wrong or were unnecessarily doing things
in complex ways.
- driver core const work, making more of the api take const * for
different parameters to make the rust bindings easier overall.
- other small fixes and updates
All of these have been in linux-next with all of the aforementioned
merge conflicts, and the one debugfs issue, which looks to be resolved
"soon".
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ5koPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymFHACfT5acDKf2Bov2Lc/5u3vBW/R6ChsAnj+LmgVI
hcDSPodj4szR40RRnzBd
=u5Ey
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the big set of driver core and debugfs updates for 6.14-rc1.
Included in here is a bunch of driver core, PCI, OF, and platform rust
bindings (all acked by the different subsystem maintainers), hence the
merge conflict with the rust tree, and some driver core api updates to
mark things as const, which will also require some fixups due to new
stuff coming in through other trees in this merge window.
There are also a bunch of debugfs updates from Al, and there is at
least one user that does have a regression with these, but Al is
working on tracking down the fix for it. In my use (and everyone
else's linux-next use), it does not seem like a big issue at the
moment.
Here's a short list of the things in here:
- driver core rust bindings for PCI, platform, OF, and some i/o
functions.
We are almost at the "write a real driver in rust" stage now,
depending on what you want to do.
- misc device rust bindings and a sample driver to show how to use
them
- debugfs cleanups in the fs as well as the users of the fs api for
places where drivers got it wrong or were unnecessarily doing
things in complex ways.
- driver core const work, making more of the api take const * for
different parameters to make the rust bindings easier overall.
- other small fixes and updates
All of these have been in linux-next with all of the aforementioned
merge conflicts, and the one debugfs issue, which looks to be resolved
"soon""
* tag 'driver-core-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (95 commits)
rust: device: Use as_char_ptr() to avoid explicit cast
rust: device: Replace CString with CStr in property_present()
devcoredump: Constify 'struct bin_attribute'
devcoredump: Define 'struct bin_attribute' through macro
rust: device: Add property_present()
saner replacement for debugfs_rename()
orangefs-debugfs: don't mess with ->d_name
octeontx2: don't mess with ->d_parent or ->d_parent->d_name
arm_scmi: don't mess with ->d_parent->d_name
slub: don't mess with ->d_name
sof-client-ipc-flood-test: don't mess with ->d_name
qat: don't mess with ->d_name
xhci: don't mess with ->d_iname
mtu3: don't mess wiht ->d_iname
greybus/camera - stop messing with ->d_iname
mediatek: stop messing with ->d_iname
netdevsim: don't embed file_operations into your structs
b43legacy: make use of debugfs_get_aux()
b43: stop embedding struct file_operations into their objects
carl9170: stop embedding file_operations into their objects
...
Add the const qualifier to all the ctl_tables in the tree except for
watchdog_hardlockup_sysctl, memory_allocation_profiling_sysctls,
loadpin_sysctl_table and the ones calling register_net_sysctl (./net,
drivers/inifiniband dirs). These are special cases as they use a
registration function with a non-const qualified ctl_table argument or
modify the arrays before passing them on to the registration function.
Constifying ctl_table structs will prevent the modification of
proc_handler function pointers as the arrays would reside in .rodata.
This is made possible after commit 78eb4ea25c ("sysctl: treewide:
constify the ctl_table argument of proc_handlers") constified all the
proc_handlers.
Created this by running an spatch followed by a sed command:
Spatch:
virtual patch
@
depends on !(file in "net")
disable optional_qualifier
@
identifier table_name != {
watchdog_hardlockup_sysctl,
iwcm_ctl_table,
ucma_ctl_table,
memory_allocation_profiling_sysctls,
loadpin_sysctl_table
};
@@
+ const
struct ctl_table table_name [] = { ... };
sed:
sed --in-place \
-e "s/struct ctl_table .table = &uts_kern/const struct ctl_table *table = \&uts_kern/" \
kernel/utsname_sysctl.c
Reviewed-by: Song Liu <song@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org> # for kernel/trace/
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> # SCSI
Reviewed-by: Darrick J. Wong <djwong@kernel.org> # xfs
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Bill O'Donnell <bodonnel@redhat.com>
Acked-by: Baoquan He <bhe@redhat.com>
Acked-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Acked-by: Anna Schumaker <anna.schumaker@oracle.com>
Signed-off-by: Joel Granados <joel.granados@kernel.org>
this pull are:
- "lib min_heap: Improve min_heap safety, testing, and documentation"
from Kuan-Wei Chiu provides various tightenings to the min_heap library
code.
- "xarray: extract __xa_cmpxchg_raw" from Tamir Duberstein preforms some
cleanup and Rust preparation in the xarray library code.
- "Update reference to include/asm-<arch>" from Geert Uytterhoeven fixes
pathnames in some code comments.
- "Converge on using secs_to_jiffies()" from Easwar Hariharan uses the
new secs_to_jiffies() in various places where that is appropriate.
- "ocfs2, dlmfs: convert to the new mount API" from Eric Sandeen
switches two filesystems to the new mount API.
- "Convert ocfs2 to use folios" from Matthew Wilcox does that.
- "Remove get_task_comm() and print task comm directly" from Yafang Shao
removes now-unneeded calls to get_task_comm() in various places.
- "squashfs: reduce memory usage and update docs" from Phillip Lougher
implements some memory savings in squashfs and performs some
maintainability work.
- "lib: clarify comparison function requirements" from Kuan-Wei Chiu
tightens the sort code's behaviour and adds some maintenance work.
- "nilfs2: protect busy buffer heads from being force-cleared" from
Ryusuke Konishi fixes an issues in nlifs when the fs is presented with a
corrupted image.
- "nilfs2: fix kernel-doc comments for function return values" from
Ryusuke Konishi fixes some nilfs kerneldoc.
- "nilfs2: fix issues with rename operations" from Ryusuke Konishi
addresses some nilfs BUG_ONs which syzbot was able to trigger.
- "minmax.h: Cleanups and minor optimisations" from David Laight
does some maintenance work on the min/max library code.
- "Fixes and cleanups to xarray" from Kemeng Shi does maintenance work
on the xarray library code.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZ5SP5QAKCRDdBJ7gKXxA
jqN7AQChvwXGG43n4d5SDiA/rH7ddvowQcDqhC9cAMJ1ReR7qwEA8/LIWDE4PdMX
mJnaZ1/ibpEpearrChCViApQtcyEGQI=
=ti4E
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2025-01-24-23-16' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"Mainly individually changelogged singleton patches. The patch series
in this pull are:
- "lib min_heap: Improve min_heap safety, testing, and documentation"
from Kuan-Wei Chiu provides various tightenings to the min_heap
library code
- "xarray: extract __xa_cmpxchg_raw" from Tamir Duberstein preforms
some cleanup and Rust preparation in the xarray library code
- "Update reference to include/asm-<arch>" from Geert Uytterhoeven
fixes pathnames in some code comments
- "Converge on using secs_to_jiffies()" from Easwar Hariharan uses
the new secs_to_jiffies() in various places where that is
appropriate
- "ocfs2, dlmfs: convert to the new mount API" from Eric Sandeen
switches two filesystems to the new mount API
- "Convert ocfs2 to use folios" from Matthew Wilcox does that
- "Remove get_task_comm() and print task comm directly" from Yafang
Shao removes now-unneeded calls to get_task_comm() in various
places
- "squashfs: reduce memory usage and update docs" from Phillip
Lougher implements some memory savings in squashfs and performs
some maintainability work
- "lib: clarify comparison function requirements" from Kuan-Wei Chiu
tightens the sort code's behaviour and adds some maintenance work
- "nilfs2: protect busy buffer heads from being force-cleared" from
Ryusuke Konishi fixes an issues in nlifs when the fs is presented
with a corrupted image
- "nilfs2: fix kernel-doc comments for function return values" from
Ryusuke Konishi fixes some nilfs kerneldoc
- "nilfs2: fix issues with rename operations" from Ryusuke Konishi
addresses some nilfs BUG_ONs which syzbot was able to trigger
- "minmax.h: Cleanups and minor optimisations" from David Laight does
some maintenance work on the min/max library code
- "Fixes and cleanups to xarray" from Kemeng Shi does maintenance
work on the xarray library code"
* tag 'mm-nonmm-stable-2025-01-24-23-16' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (131 commits)
ocfs2: use str_yes_no() and str_no_yes() helper functions
include/linux/lz4.h: add some missing macros
Xarray: use xa_mark_t in xas_squash_marks() to keep code consistent
Xarray: remove repeat check in xas_squash_marks()
Xarray: distinguish large entries correctly in xas_split_alloc()
Xarray: move forward index correctly in xas_pause()
Xarray: do not return sibling entries from xas_find_marked()
ipc/util.c: complete the kernel-doc function descriptions
gcov: clang: use correct function param names
latencytop: use correct kernel-doc format for func params
minmax.h: remove some #defines that are only expanded once
minmax.h: simplify the variants of clamp()
minmax.h: move all the clamp() definitions after the min/max() ones
minmax.h: use BUILD_BUG_ON_MSG() for the lo < hi test in clamp()
minmax.h: reduce the #define expansion of min(), max() and clamp()
minmax.h: update some comments
minmax.h: add whitespace around operators and after commas
nilfs2: do not update mtime of renamed directory that is not moved
nilfs2: handle errors that nilfs_prepare_chunk() may return
CREDITS: fix spelling mistake
...
Updates to the usual drivers (ufs, lpfc, fnic, qla2xx, mpi3mr) The
major core change is the renaming of the slave_ methods plus a bit of
constification. The rest are minor updates and fixes.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZ5ZQKSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQMdAQCyVlDZ
v/3EFCuC4U1l70mMu8t+F4RPvqYxM3QPCi5dDQEA751YN/kaqxeXZDqGUKCAOE3K
Nl4XFTfLEkDVrQFFqPc=
=9sV8
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, fnic, qla2xx, mpi3mr).
The major core change is the renaming of the slave_ methods plus a bit
of constification. The rest are minor updates and fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (103 commits)
scsi: fnic: Propagate SCSI error code from fnic_scsi_drv_init()
scsi: fnic: Test for memory allocation failure and return error code
scsi: fnic: Return appropriate error code from failure of scsi drv init
scsi: fnic: Return appropriate error code for mem alloc failure
scsi: fnic: Remove always-true IS_FNIC_FCP_INITIATOR macro
scsi: fnic: Fix use of uninitialized value in debug message
scsi: fnic: Delete incorrect debugfs error handling
scsi: fnic: Remove unnecessary else to fix warning in FDLS FIP
scsi: fnic: Remove extern definition from .c files
scsi: fnic: Remove unnecessary else and unnecessary break in FDLS
scsi: mpi3mr: Fix possible crash when setting up bsg fails
scsi: ufs: bsg: Set bsg_queue to NULL after removal
scsi: ufs: bsg: Delete bsg_dev when setting up bsg fails
scsi: st: Don't set pos_unknown just after device recognition
scsi: aic7xxx: Fix build 'aicasm' warning
scsi: Revert "scsi: ufs: core: Probe for EXT_IID support"
scsi: storvsc: Ratelimit warning logs to prevent VM denial of service
scsi: scsi_debug: Constify sdebug_driver_template
scsi: documentation: Corrections for struct updates
scsi: driver-api: documentation: Change what is added to docbook
...
This patch adds scsi_check_passthrough() tests for the cases where a
command completes successfully and when the command failed but the caller
did not pass in a list of failures.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20250113180757.16691-1-michael.christie@oracle.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Add preempt lazy support
- Deprecate cxl and cxl flash driver
- Fix a possible IOMMU related OOPS at boot on pSeries
- Optimize sched_clock() in ppc32 by replacing mulhdu() by mul_u64_u64_shr()
Thanks to: Andrew Donnellan, Andy Shevchenko, Ankur Arora, Christophe Leroy,
Frederic Barrat, Gaurav Batra, Luis Felipe Hernandez, Michael Ellerman, Nilay
Shroff, Ricardo B. Marliere, Ritesh Harjani (IBM), Sebastian Andrzej Siewior,
Shrikanth Hegde, Sourabh Jain, Thorsten Blum, Zhu Jun.
-----BEGIN PGP SIGNATURE-----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=ctY4
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Madhavan Srinivasan:
- Add preempt lazy support
- Deprecate cxl and cxl flash driver
- Fix a possible IOMMU related OOPS at boot on pSeries
- Optimize sched_clock() in ppc32 by replacing mulhdu() by
mul_u64_u64_shr()
Thanks to Andrew Donnellan, Andy Shevchenko, Ankur Arora, Christophe
Leroy, Frederic Barrat, Gaurav Batra, Luis Felipe Hernandez, Michael
Ellerman, Nilay Shroff, Ricardo B. Marliere, Ritesh Harjani (IBM),
Sebastian Andrzej Siewior, Shrikanth Hegde, Sourabh Jain, Thorsten Blum,
and Zhu Jun.
* tag 'powerpc-6.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix argument order to timer_sub()
powerpc/prom_init: Use IS_ENABLED()
powerpc/pseries/iommu: IOMMU incorrectly marks MMIO range in DDW
powerpc: Use str_on_off() helper in check_cache_coherency()
powerpc: Large user copy aware of full:rt:lazy preemption
powerpc: Add preempt lazy support
powerpc/book3s64/hugetlb: Fix disabling hugetlb when fadump is active
powerpc/vdso: Mark the vDSO code read-only after init
powerpc/64: Use get_user() in start_thread()
macintosh: declare ctl_table as const
selftest/powerpc/ptrace: Cleanup duplicate macro definitions
selftest/powerpc/ptrace/ptrace-pkey: Remove duplicate macros
selftest/powerpc/ptrace/core-pkey: Remove duplicate macros
powerpc/8xx: Drop legacy-of-mm-gpiochip.h header
scsi/cxlflash: Deprecate driver
cxl: Deprecate driver
selftests/powerpc: Fix typo in test-vphn.c
powerpc/xmon: Use str_yes_no() helper in dump_one_paca()
powerpc/32: Replace mulhdu() by mul_u64_u64_shr()
-----BEGIN PGP SIGNATURE-----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=ufpE
-----END PGP SIGNATURE-----
Merge tag 'for-6.14/io_uring-20250119' of git://git.kernel.dk/linux
Pull io_uring updates from Jens Axboe:
"Not a lot in terms of features this time around, mostly just cleanups
and code consolidation:
- Support for PI meta data read/write via io_uring, with NVMe and
SCSI covered
- Cleanup the per-op structure caching, making it consistent across
various command types
- Consolidate the various user mapped features into a concept called
regions, making the various users of that consistent
- Various cleanups and fixes"
* tag 'for-6.14/io_uring-20250119' of git://git.kernel.dk/linux: (56 commits)
io_uring/fdinfo: fix io_uring_show_fdinfo() misuse of ->d_iname
io_uring: reuse io_should_terminate_tw() for cmds
io_uring: Factor out a function to parse restrictions
io_uring/rsrc: require cloned buffers to share accounting contexts
io_uring: simplify the SQPOLL thread check when cancelling requests
io_uring: expose read/write attribute capability
io_uring/rw: don't gate retry on completion context
io_uring/rw: handle -EAGAIN retry at IO completion time
io_uring/rw: use io_rw_recycle() from cleanup path
io_uring/rsrc: simplify the bvec iter count calculation
io_uring: ensure io_queue_deferred() is out-of-line
io_uring/rw: always clear ->bytes_done on io_async_rw setup
io_uring/rw: use NULL for rw->free_iovec assigment
io_uring/rw: don't mask in f_iocb_flags
io_uring/msg_ring: Drop custom destructor
io_uring: Move old async data allocation helper to header
io_uring/rw: Allocate async data through helper
io_uring/net: Allocate msghdr async data through helper
io_uring/uring_cmd: Allocate async data through generic helper
io_uring/poll: Allocate apoll with generic alloc_cache helper
...
-----BEGIN PGP SIGNATURE-----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=EXYs
-----END PGP SIGNATURE-----
Merge tag 'for-6.14/block-20250118' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe pull requests via Keith:
- Target support for PCI-Endpoint transport (Damien)
- TCP IO queue spreading fixes (Sagi, Chaitanya)
- Target handling for "limited retry" flags (Guixen)
- Poll type fix (Yongsoo)
- Xarray storage error handling (Keisuke)
- Host memory buffer free size fix on error (Francis)
- MD pull requests via Song:
- Reintroduce md-linear (Yu Kuai)
- md-bitmap refactor and fix (Yu Kuai)
- Replace kmap_atomic with kmap_local_page (David Reaver)
- Quite a few queue freeze and debugfs deadlock fixes
Ming introduced lockdep support for this in the 6.13 kernel, and it
has (unsurprisingly) uncovered quite a few issues
- Use const attributes for IO schedulers
- Remove bio ioprio wrappers
- Fixes for stacked device atomic write support
- Refactor queue affinity helpers, in preparation for better supporting
isolated CPUs
- Cleanups of loop O_DIRECT handling
- Cleanup of BLK_MQ_F_* flags
- Add rotational support for null_blk
- Various fixes and cleanups
* tag 'for-6.14/block-20250118' of git://git.kernel.dk/linux: (106 commits)
block: Don't trim an atomic write
block: Add common atomic writes enable flag
md/md-linear: Fix a NULL vs IS_ERR() bug in linear_add()
block: limit disk max sectors to (LLONG_MAX >> 9)
block: Change blk_stack_atomic_writes_limits() unit_min check
block: Ensure start sector is aligned for stacking atomic writes
blk-mq: Move more error handling into blk_mq_submit_bio()
block: Reorder the request allocation code in blk_mq_submit_bio()
nvme: fix bogus kzalloc() return check in nvme_init_effects_log()
md/md-bitmap: move bitmap_{start, end}write to md upper layer
md/raid5: implement pers->bitmap_sector()
md: add a new callback pers->bitmap_sector()
md/md-bitmap: remove the last parameter for bimtap_ops->endwrite()
md/md-bitmap: factor behind write counters out from bitmap_{start/end}write()
md: Replace deprecated kmap_atomic() with kmap_local_page()
md: reintroduce md-linear
partitions: ldm: remove the initial kernel-doc notation
blk-cgroup: rwstat: fix kernel-doc warnings in header file
blk-cgroup: fix kernel-doc warnings in header file
nbd: fix partial sending
...
Currently only stacked devices need to explicitly enable atomic writes by
setting BLK_FEAT_ATOMIC_WRITES_STACKED flag.
This does not work well for device mapper stacking devices, as there many
sets of limits are stacked and what is the 'bottom' and 'top' device can
swapped. This means that BLK_FEAT_ATOMIC_WRITES_STACKED needs to be set
for many queue limits, which is messy.
Generalize enabling atomic writes enabling by ensuring that all devices
must explicitly set a flag - that includes NVMe, SCSI sd, and md raid.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@kernel.org>
Link: https://lore.kernel.org/r/20250116170301.474130-2-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Karan Tilak Kumar <kartilak@cisco.com> says:
Hi Martin, reviewers,
This cover letter describes the feature: add support for Fabric
Discovery and Login Services (FDLS) to fnic driver.
This functionality is needed to support port channel RSCN (PC-RSCN)
handling and serves as a base to create FC-NVME initiators
(planned later), and eCPU handling (planned later).
It is used to discover the fabric and target ports associated with the
fabric. It will then login to the target ports that are zoned to it.
The driver uses the tport structure presented by FDLS.
Port channel RSCN is a Cisco vendor specific RSCN event. It is
applicable only to Cisco UCS fabrics.
In cases where the eCPU in the UCS VIC (Unified Computing Services
Virtual Interface Card) hangs, a fabric log out is sent to the fabric.
Upon successful log out from the fabric, the IO path is failed over to
a new path.
Generally from a feature perspective, the code is divided into adding
support for this functionality initially. Then, code has been added to
modify the IO path and interfaces. Finally, support for port channel
RSCN handling has been added.
Here are the headers of some of the salient patches:
o add headers and definitions for FDLS
o add support for fabric based solicited requests and responses
o add support for target based solicited requests and responses
o add support for unsolicited requests and responses
o add support for FDMI
o add support for FIP
o add functionality in fnic to support FDLS
o modify IO path to use FDLS and tport
o modify fnic interfaces to use FDLS
o add support to handle port channel RSCN
Even though the patches have been made into a series, some patches are
heavier than others. But, every effort has been made to keep the
purpose of each patch as a single-purpose, and to compile cleanly.
All the individual patches compile cleanly. The compiler used is GCC
13.3. Some function calls have been coded as placeholders with
appropriate comments to avoid compiler warnings.
This patchset has been tested as a whole. Therefore, the tested-by
fields have been added only to one patch in the set. I've refrained
from adding tested-by to most of the patches, so as to not mislead the
reviewer/reader.
A brief note on the unit tests:
o. Perform zone in zone out testing in a loop: remove a target
port from the zone, add it to the zone in a loop. 1000+ iterations
of this test have been successful.
o. Configure multipathing, and run link flaps on single link.
IOs drop briefly, but pick up as expected.
o. Configure multipathing, and run link flaps on two links, with a
30 second delay in between. IOs drop briefly, but pick up as expected.
o. Module load/unload test.
o. Repeat the above tests with 1 queue and 64 queues.
All tests were successful.
Please consider this patch series for the next merge window.
Link: https://lore.kernel.org/r/20241212020312.4786-1-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct the spelling dictionary so that future instances will be caught by
checkpatch, and fix the instances found.
Link: https://lkml.kernel.org/r/20241211154903.47027-1-cvam0000@gmail.com
Signed-off-by: Shivam Chaudhary <cvam0000@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Naveen N Rao <naveen@kernel.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Shivam Chaudhary <cvam0000@gmail.com>
Cc: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Commit b35108a51c ("jiffies: Define secs_to_jiffies()") introduced
secs_to_jiffies(). As the value here is a multiple of 1000, use
secs_to_jiffies() instead of msecs_to_jiffies to avoid the multiplication.
This is converted using scripts/coccinelle/misc/secs_to_jiffies.cocci with
the following Coccinelle rules:
@@ constant C; @@
- msecs_to_jiffies(C * 1000)
+ secs_to_jiffies(C)
@@ constant C; @@
- msecs_to_jiffies(C * MSEC_PER_SEC)
+ secs_to_jiffies(C)
Link: https://lkml.kernel.org/r/20241210-converge-secs-to-jiffies-v3-11-ddfefd7e9f2a@linux.microsoft.com
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Andrew Lunn <andrew+netdev@lunn.ch>
Cc: Anna-Maria Behnsen <anna-maria@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Daniel Mack <daniel@zonque.org>
Cc: David Airlie <airlied@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Jeff Johnson <jjohnson@kernel.org>
Cc: Jeff Johnson <quic_jjohnson@quicinc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jeroen de Borst <jeroendb@google.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: Jozsef Kadlecsik <kadlec@netfilter.org>
Cc: Julia Lawall <julia.lawall@inria.fr>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Louis Peens <louis.peens@corigine.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Naveen N Rao <naveen@kernel.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Nicolas Palix <nicolas.palix@imag.fr>
Cc: Oded Gabbay <ogabbay@kernel.org>
Cc: Ofir Bitton <obitton@habana.ai>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Praveen Kaligineedi <pkaligineedi@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Shailend Chand <shailend@google.com>
Cc: Simona Vetter <simona@ffwll.ch>
Cc: Simon Horman <horms@kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Commit b35108a51c ("jiffies: Define secs_to_jiffies()") introduced
secs_to_jiffies(). As the value here is a multiple of 1000, use
secs_to_jiffies() instead of msecs_to_jiffies to avoid the multiplication.
This is converted using scripts/coccinelle/misc/secs_to_jiffies.cocci with
the following Coccinelle rules:
@@ constant C; @@
- msecs_to_jiffies(C * 1000)
+ secs_to_jiffies(C)
@@ constant C; @@
- msecs_to_jiffies(C * MSEC_PER_SEC)
+ secs_to_jiffies(C)
Link: https://lkml.kernel.org/r/20241210-converge-secs-to-jiffies-v3-10-ddfefd7e9f2a@linux.microsoft.com
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Andrew Lunn <andrew+netdev@lunn.ch>
Cc: Anna-Maria Behnsen <anna-maria@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Daniel Mack <daniel@zonque.org>
Cc: David Airlie <airlied@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Jeff Johnson <jjohnson@kernel.org>
Cc: Jeff Johnson <quic_jjohnson@quicinc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jeroen de Borst <jeroendb@google.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: Jozsef Kadlecsik <kadlec@netfilter.org>
Cc: Julia Lawall <julia.lawall@inria.fr>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Louis Peens <louis.peens@corigine.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Naveen N Rao <naveen@kernel.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Nicolas Palix <nicolas.palix@imag.fr>
Cc: Oded Gabbay <ogabbay@kernel.org>
Cc: Ofir Bitton <obitton@habana.ai>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Praveen Kaligineedi <pkaligineedi@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Shailend Chand <shailend@google.com>
Cc: Simona Vetter <simona@ffwll.ch>
Cc: Simon Horman <horms@kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Commit b35108a51c ("jiffies: Define secs_to_jiffies()") introduced
secs_to_jiffies(). As the value here is a multiple of 1000, use
secs_to_jiffies() instead of msecs_to_jiffies to avoid the multiplication.
This is converted using scripts/coccinelle/misc/secs_to_jiffies.cocci with
the following Coccinelle rules:
@@ constant C; @@
- msecs_to_jiffies(C * 1000)
+ secs_to_jiffies(C)
@@ constant C; @@
- msecs_to_jiffies(C * MSEC_PER_SEC)
+ secs_to_jiffies(C)
Link: https://lkml.kernel.org/r/20241210-converge-secs-to-jiffies-v3-9-ddfefd7e9f2a@linux.microsoft.com
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Andrew Lunn <andrew+netdev@lunn.ch>
Cc: Anna-Maria Behnsen <anna-maria@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Daniel Mack <daniel@zonque.org>
Cc: David Airlie <airlied@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Jeff Johnson <jjohnson@kernel.org>
Cc: Jeff Johnson <quic_jjohnson@quicinc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jeroen de Borst <jeroendb@google.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: Jozsef Kadlecsik <kadlec@netfilter.org>
Cc: Julia Lawall <julia.lawall@inria.fr>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Louis Peens <louis.peens@corigine.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Naveen N Rao <naveen@kernel.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Nicolas Palix <nicolas.palix@imag.fr>
Cc: Oded Gabbay <ogabbay@kernel.org>
Cc: Ofir Bitton <obitton@habana.ai>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Praveen Kaligineedi <pkaligineedi@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Shailend Chand <shailend@google.com>
Cc: Simona Vetter <simona@ffwll.ch>
Cc: Simon Horman <horms@kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Fix kernel test robot warning. Test for memory allocation failure, and
free memory for queues allocated in a multiqueue and non-multiqueue
scenario. Return appropriate error code.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202412312347.FE4ZgEoM-lkp@intel.com/
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Closes: https://lore.kernel.org/r/202412312347.FE4ZgEoM-lkp@intel.com/
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Reviewed-by: Gian Carlo Boffa <gcboffa@cisco.com>
Reviewed-by: Arun Easi <aeasi@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20250110091924.17729-1-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
IS_FNIC_FCP_INITIATOR macro is not applicable at this time. Delete the
macro.
Suggested-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Reviewed-by: Gian Carlo Boffa <gcboffa@cisco.com>
Signed-off-by: Arun Easi <aeasi@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20250110091655.17643-1-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The oxid variable in fdls_process_abts_req() was only being initialized
inside the if (tport) block, but was being used in a debug print statement
after that block. If tport was NULL, oxid would remain uninitialized. Move
the oxid initialization to happen at declaration using
FNIC_STD_GET_OX_ID(fchdr).
Fixes: f828af44b8 ("scsi: fnic: Add support for unsolicited requests and responses")
Closes: https://scan7.scan.coverity.com/#/project-view/52337/11354?selectedIssue=1602772
Signed-off-by: Dheeraj Reddy Jonnalagadda <dheeraj.linuxdev@gmail.com>
Link: https://lore.kernel.org/r/20250108050916.52721-1-dheeraj.linuxdev@gmail.com
Reviewed-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Debugfs functions are not supposed to require error checking and, in fact,
adding checks would normally lead to the driver refusing to load when
CONFIG_DEBUGFS is disabled.
What saves us here is that this code checks for NULL instead of error
pointers so the error checking is all dead code. Delete it.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/a5c237cd-449b-4f9d-bcff-6285fb7c28d1@stanley.mountain
Reviewed-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If bsg_setup_queue() fails, the bsg_queue is assigned a non-NULL value.
Consequently, in mpi3mr_bsg_exit(), the condition "if(!mrioc->bsg_queue)"
will not be satisfied, preventing execution from entering
bsg_remove_queue(), which could lead to the following crash:
BUG: kernel NULL pointer dereference, address: 000000000000041c
Call Trace:
<TASK>
mpi3mr_bsg_exit+0x1f/0x50 [mpi3mr]
mpi3mr_remove+0x6f/0x340 [mpi3mr]
pci_device_remove+0x3f/0xb0
device_release_driver_internal+0x19d/0x220
unbind_store+0xa4/0xb0
kernfs_fop_write_iter+0x11f/0x200
vfs_write+0x1fc/0x3e0
ksys_write+0x67/0xe0
do_syscall_64+0x38/0x80
entry_SYSCALL_64_after_hwframe+0x78/0xe2
Fixes: 4268fa7513 ("scsi: mpi3mr: Add bsg device support")
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250107022032.24006-1-kanie@linux.alibaba.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 9604eea5bd ("scsi: st: Add third party poweron reset handling") in
v6.6 added new code to handle the Power On/Reset Unit Attention (POR UA)
sense data. This was in addition to the existing method. When this Unit
Attention is received, the driver blocks attempts to read, write and some
other operations because the reset may have rewinded the tape. Because of
the added code, also the initial POR UA resulted in blocking operations,
including those that are used to set the driver options after the device is
recognized. Also, reading and writing are refused, whereas they succeeded
before this commit.
Add code to not set pos_unknown to block operations if the POR UA is
received from the first test_ready() call after the st device has been
created. This restores the behavior before v6.6.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://lore.kernel.org/r/20241216113755.30415-1-Kai.Makisara@kolumbus.fi
Fixes: 9604eea5bd ("scsi: st: Add third party poweron reset handling")
CC: stable@vger.kernel.org
Closes: https://lore.kernel.org/linux-scsi/2201CF73-4795-4D3B-9A79-6EE5215CF58D@kolumbus.fi/
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building with CONFIG_AIC7XXX_BUILD_FIRMWARE=y or
CONFIG_AIC79XX_BUILD_FIRMWARE=y, the warning messages are as follows:
aicasm_gram.tab.c:1722:16: warning: implicit declaration of function
‘yylex’ [-Wimplicit-function-declaration]
aicasm_macro_gram.c:68:25: warning: implicit declaration of function
‘mmlex’ [-Wimplicit-function-declaration]
aicasm_scan.l:417:6: warning: implicit declaration of function
‘mm_switch_to_buffer’
aicasm_scan.l:418:6: warning: implicit declaration of function
‘mmparse’
aicasm_scan.l:421:6: warning: implicit declaration of function
‘mm_delete_buffer’
The solution is to add the corresponding function declaration to the
corresponding file.
Signed-off-by: wangdicheng <wangdicheng@kylinos.cn>
Signed-off-by: huanglei <huanglei@kylinos.cn>
Link: https://lore.kernel.org/r/20241206071926.63832-1-wangdich9700@163.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's better to have sdebug_driver_template as const, so update the probe
path to set the shost members directly after allocation and make that
change.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20250107153325.1689432-1-john.g.garry@oracle.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix kernel-doc for sas_port_alloc(), sas_port_alloc_num(), and
spi_dv_device(). This allows them to be part of the SCSI driver-api
docbook.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20241212205217.597844-6-rdunlap@infradead.org
CC: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
CC: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add kernel-doc for scsi_add_device() since it is exported. This allows it
to be part of the SCSI driver-api docbook.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20241212205217.597844-5-rdunlap@infradead.org
CC: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
CC: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add kernel-doc for scsi_failures_reset_retries() and scsi_alloc_request()
since these are exported. This allows them to be part of the SCSI
driver-api docbook.
Fix kernel-doc comments for scsi_vpd_tpg_id() [add kernel-doc for one
parameter and fix a typo].
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20241212205217.597844-4-rdunlap@infradead.org
CC: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
CC: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add kernel-doc for scsi_set_medium_removal(), scsi_cmd_allowed(), and
scsi_ioctl_block_when_processing_errors() since these are exported. This
allows them to be part of the SCSI driver-api docbook.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20241212205217.597844-3-rdunlap@infradead.org
CC: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
CC: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert scsi_report_bus_reset() and scsi_report_device_reset() to
kernel-doc since they are exported. This allows them to be part of the
driver-api/scsi.rst docbook.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20241212205217.597844-2-rdunlap@infradead.org
CC: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
CC: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a helper that freezes the queue, updates the queue limits and
unfreezes the queue and convert all open coded versions of that to the
new helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20250110054726.1499538-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The ISCSI_UEVENT_GET_HOST_STATS request is already handled in
iscsi_get_host_stats(). This fix ensures that redundant responses are
skipped in iscsi_if_rx().
- On success: send reply and stats from iscsi_get_host_stats()
within if_recv_msg().
- On error: fall through.
Signed-off-by: Xiang Zhang <hawkxiang.cpp@gmail.com>
Link: https://lore.kernel.org/r/20250107022432.65390-1-hawkxiang.cpp@gmail.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_check_passthrough() is always called, but it doesn't check for if a
command completed successfully. As a result, if a command was successful and
the caller used SCMD_FAILURE_RESULT_ANY to indicate what failures it wanted
to retry, we will end up retrying the command. This will cause delays during
device discovery because of the command being sent multiple times. For some
USB devices it can also cause the wrong device size to be used.
This patch adds a check for if the command was successful. If it is we
return immediately instead of trying to match a failure.
Fixes: 994724e6b3 ("scsi: core: Allow passthrough to request midlayer retries")
Reported-by: Kris Karas <bugs-a21@moonlit-rail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219652
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20250107010220.7215-1-michael.christie@oracle.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use a plain BLK_MQ_F_* flag to select the round robin tag selection
instead of overlaying an enum with just two possible values into the
flags space.
Doing so allows adding a BLK_MQ_F_MAX sentinel for simplified overflow
checking in the messy debugfs helpers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20250106083531.799976-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Constify the following API:
struct device *device_find_child(struct device *dev, void *data,
int (*match)(struct device *dev, void *data));
To :
struct device *device_find_child(struct device *dev, const void *data,
device_match_t match);
typedef int (*device_match_t)(struct device *dev, const void *data);
with the following reasons:
- Protect caller's match data @*data which is for comparison and lookup
and the API does not actually need to modify @*data.
- Make the API's parameters (@match)() and @data have the same type as
all of other device finding APIs (bus|class|driver)_find_device().
- All kinds of existing device match functions can be directly taken
as the API's argument, they were exported by driver core.
Constify the API and adapt for various existing usages.
BTW, various subsystem changes are squashed into this commit to meet
'git bisect' requirement, and this commit has the minimal and simplest
changes to complement squashing shortcoming, and that may bring extra
code improvement.
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Uwe Kleine-König <ukleinek@kernel.org> # for drivers/pwm
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20241224-const_dfc_done-v5-4-6623037414d4@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to handle port channel RSCN.
Port channel RSCN is a Cisco vendor specific RSCN event. It is applicable
only to Cisco UCS fabrics. If there's a change in the port channel
configuration, an RCSN is sent to fnic. This is used to serially reset the
scsi initiator fnics so that there's no all paths down scenario. The
affected fnics are added to a list that are reset with a small time gap
between them.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Reviewed-by: Gian Carlo Boffa <gcboffa@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20241212020312.4786-15-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace existing host structure with fnic host.
Add headers from scsi to support new functionality.
Remove unused code and declarations.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Reviewed-by: Gian Carlo Boffa <gcboffa@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20241212020312.4786-14-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add statistics and related functionality for FDLS.
Add supporting functions to display stats.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Reviewed-by: Gian Carlo Boffa <gcboffa@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20241212020312.4786-13-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify fnic driver interfaces to use FDLS and supporting functions.
Refactor code in fnic_probe and fnic_remove.
Get fnic from shost_priv.
Add error handling in stats processing functions.
Modify some print statements.
Add support to do module unload cleanup.
Use placeholder functions/modify function declarations to not break
compilation.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Reviewed-by: Gian Carlo Boffa <gcboffa@cisco.com>
Co-developed-by: Arun Easi <aeasi@cisco.com>
Signed-off-by: Arun Easi <aeasi@cisco.com>
Co-developed-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20241212020312.4786-12-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify IO path to use FDLS.
Add helper functions to process IOs.
Remove unused template functions.
Clean up obsolete code.
Refactor old function definitions.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410210147.fQp7tYeb-lkp@intel.com/
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Reviewed-by: Gian Carlo Boffa <gcboffa@cisco.com>
Reviewed-by: Arun Easi <aeasi@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20241212020312.4786-11-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add interfaces in fnic to use FDLS services.
Modify link up and link down functionality to use FDLS.
Replace existing interfaces to handle new functionality provided by FDLS.
Modify data types of some data members to handle new functionality.
Add processing of tports and handling of tports.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409292037.ZYWZwIK6-lkp@intel.com/
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Co-developed-by: Gian Carlo Boffa <gcboffa@cisco.com>
Signed-off-by: Gian Carlo Boffa <gcboffa@cisco.com>
Co-developed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Signed-off-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Co-developed-by: Arun Easi <aeasi@cisco.com>
Signed-off-by: Arun Easi <aeasi@cisco.com>
Co-developed-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20241212020312.4786-10-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add and integrate support for FCoE Initialization (protocol) FIP. This
protocol will be exercised on Cisco UCS rack servers.
Add support to specifically print FIP related debug messages.
Replace existing definitions to handle new data structures.
Clean up old and obsolete definitions.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409291955.FcMZfNSt-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202412081904.pXwdx15J-lkp@intel.com/
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Co-developed-by: Gian Carlo Boffa <gcboffa@cisco.com>
Signed-off-by: Gian Carlo Boffa <gcboffa@cisco.com>
Co-developed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Signed-off-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Co-developed-by: Arun Easi <aeasi@cisco.com>
Signed-off-by: Arun Easi <aeasi@cisco.com>
Co-developed-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20241212020312.4786-9-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for target based solicited requests and responses.
Add support for tport definitions and processing.
Add support for restarting the IT nexus.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202406120146.xchlZbqX-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202412081427.SlsFIJY4-lkp@intel.com/
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Co-developed-by: Gian Carlo Boffa <gcboffa@cisco.com>
Signed-off-by: Gian Carlo Boffa <gcboffa@cisco.com>
Co-developed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Signed-off-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Co-developed-by: Arun Easi <aeasi@cisco.com>
Signed-off-by: Arun Easi <aeasi@cisco.com>
Co-developed-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20241212020312.4786-5-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sending host information to shost_printk() prior to host initialization in
fnic is unnecessary. Replace shost_printk() and a printk() prior to this
initialization with dev_info() and dev_err() accordingly.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Reviewed-by: Gian Carlo Boffa <gcboffa@cisco.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20241212020312.4786-2-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Skip the reset settle delay during error handling since the scsi_debug
driver doesn't need this delay.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241216184852.2626339-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Thomas Weißschuh <linux@weissschuh.net> says:
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Link: https://lore.kernel.org/r/20241216-sysfs-const-bin_attr-scsi-v1-0-f0a5e54b3437@weissschuh.net
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sysfs core now allows instances of 'struct bin_attribute' to be moved
into read-only memory. Make use of that to protect them against accidental
or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241216-sysfs-const-bin_attr-scsi-v1-11-f0a5e54b3437@weissschuh.net
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sysfs core now allows instances of 'struct bin_attribute' to be moved
into read-only memory. Make use of that to protect them against accidental
or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241216-sysfs-const-bin_attr-scsi-v1-10-f0a5e54b3437@weissschuh.net
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sysfs core now allows instances of 'struct bin_attribute' to be moved
into read-only memory. Make use of that to protect them against accidental
or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241216-sysfs-const-bin_attr-scsi-v1-9-f0a5e54b3437@weissschuh.net
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sysfs core now allows instances of 'struct bin_attribute' to be moved
into read-only memory. Make use of that to protect them against accidental
or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241216-sysfs-const-bin_attr-scsi-v1-8-f0a5e54b3437@weissschuh.net
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sysfs core now allows instances of 'struct bin_attribute' to be moved
into read-only memory. Make use of that to protect them against accidental
or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241216-sysfs-const-bin_attr-scsi-v1-7-f0a5e54b3437@weissschuh.net
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sysfs core now allows instances of 'struct bin_attribute' to be moved
into read-only memory. Make use of that to protect them against accidental
or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241216-sysfs-const-bin_attr-scsi-v1-6-f0a5e54b3437@weissschuh.net
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sysfs core now allows instances of 'struct bin_attribute' to be moved
into read-only memory. Make use of that to protect them against accidental
or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241216-sysfs-const-bin_attr-scsi-v1-5-f0a5e54b3437@weissschuh.net
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sysfs core now allows instances of 'struct bin_attribute' to be moved
into read-only memory. Make use of that to protect them against accidental
or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241216-sysfs-const-bin_attr-scsi-v1-4-f0a5e54b3437@weissschuh.net
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sysfs core now allows instances of 'struct bin_attribute' to be moved
into read-only memory. Make use of that to protect them against accidental
or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241216-sysfs-const-bin_attr-scsi-v1-3-f0a5e54b3437@weissschuh.net
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sysfs core now allows instances of 'struct bin_attribute' to be moved
into read-only memory. Make use of that to protect them against accidental
or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241216-sysfs-const-bin_attr-scsi-v1-2-f0a5e54b3437@weissschuh.net
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sysfs core now allows instances of 'struct bin_attribute' to be moved
into read-only memory. Make use of that to protect them against accidental
or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241216-sysfs-const-bin_attr-scsi-v1-1-f0a5e54b3437@weissschuh.net
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Justin Tee <justintee8345@gmail.com> says:
Update lpfc to revision 14.4.0.7
This patch set contains fixes related to smatch, clean up of obsolete code
and global spinlocks, changes to ADISC and LS_RJT handling, and support for
large fw object reads used in proprietary applications.
The patches were cut against Martin's 6.14/scsi-queue tree.
Link: https://lore.kernel.org/r/20241212233309.71356-1-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current lpfc bsg implementation allows a maximum fw read object size of
30KB. Implementation and support for read object mailbox commands for fw
objects larger than 30KB are now required for proprietary applications.
Thus, update the lpfc_sli_config_emb0_subsys structure and its associated
submission and completion paths to accommodate for an alternative form of
read object command that supports large fw objects.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241212233309.71356-9-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are unused fields in mailbox commands that query for firmware
configuration information. As such, update the struct definitions by
correcting the name of certain fields and removing the unused fields.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241212233309.71356-8-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In attempt to reduce the amount of unnecessary ndlp->lock acquisitions in
the lpfc driver, change save_flags into an unsigned long bitmask and use
clear_bit/test_bit bitwise atomic APIs instead of reliance on ndlp->lock
for synchronization.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241212233309.71356-7-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a LS_RJT is received with reason explanation authentication required,
current driver logic is to retry the PLOGI up to 48 times. In the worse
case scenario, 48 retries can take longer than dev_loss_tmo and if there is
an RSCN received indicating an authentication requirement change, the
driver may miss processing it. Fix by adding logic to specifically handle
reason explanation authentication required and set the max retry count to 8
times.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241212233309.71356-6-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In lpfc_check_adisc, remove the requirement that the ndlp object must have
been RPI registered. Whether or not the ndlp is RPI registered is
unrelated to verifying that the received ADISC is intended for that ndlp
rport object.
After ADISC receipt, there's no need to put the ndlp state into NPR. Let
the cmpl routines from the actions taken earlier in ADISC handling set the
proper ndlp state.
Also, refactor when a RESUME_RPI mailbox command should be sent. It should
only be sent if the RPI registered flag is set.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241212233309.71356-5-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the NLP_TARGET_REMOVE flag as its usage is obsolete. The current
framework is to rely on the lpfc_dev_loss_tmo_callbk from upper layer to
notify final ndlp kref release. There's no need to specifically set
NLP_EVT_DEVICE_RM when a LOGO completes. The dev_loss_tmo_callbk is
responsible for the final kref put.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241212233309.71356-4-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Qualify setting the REG_FCFI MAM field to FCoE adapters only by keying off
HBA_FCOE_MODE phba->hba_flag. The field is not applicable to FC adapters.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241212233309.71356-3-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix smatch warning by redefining local variable memory_flags from int to
gfp_t.
lpfc_scsi.c: warning: incorrect type in argument 2 (different base types)
lpfc_scsi.c: expected restricted gfp_t [usertype] gfp_mask
lpfc_scsi.c: got int memory_flags
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241212233309.71356-2-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* reported by Coverity ID 1602240
* ldev_info is always true, therefore the branch statement is never called.
Fixes: 081ff398c5 ("scsi: myrb: Add Mylex RAID controller (block interface)")
Cc: Hannes Reinecke <hare@kernel.org>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ariel Otilibili <ariel.otilibili-anieli@eurecom.fr>
Link: https://lore.kernel.org/r/20241213225852.62741-2-ariel.otilibili-anieli@eurecom.fr
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the code does:
if (x == 0) {
x &= ~0x3;
x |= 0x1;
}
Zeroing bits 0 and 1 of a variable that is 0 is not necessary. So directly
set the variable to 1.
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Fixes: f92363d123 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS")
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/20241212221817.78940-2-pmenzel@molgen.mpg.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Linux 5.15 logs the error below
mpt3sas_cm0: overriding NVDATA EEDPTagMode setting
on a Dell PowerEdge T440 with the card below.
5e:00.0 Serial Attached SCSI controller [0107]: Broadcom / LSI SAS3008 PCI-Express Fusion-MPT SAS-3 [1000:0097] (rev 02)
It’s not clear to a user what this error is about. As a first step to
improve this, add the values to the error message.
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/20241212221817.78940-1-pmenzel@molgen.mpg.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
isci_remote_device_reset_complete() last use was removed in 2012 by commit
14aaa9f0a3 ("isci: Redesign device suspension, abort, cleanup.")
Remove it.
It was the last user of sci_remote_device_reset_complete().
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20241223180218.50426-1-linux@treblig.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
iscsi_create_session() last use was removed in 2008 by commit 756135215e
("[SCSI] iscsi: remove session and host binding in libiscsi")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20241223180110.50266-1-linux@treblig.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the proper API instead of open coding it.
However it looks like qedi_percpu_io_thread() kthread could be replaced by
the use of a high prio workqueue instead.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20241211154035.75565-6-frederic@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the proper API instead of open coding it.
However it looks like bnx2i_percpu_io_thread() kthread could be replaced by
the use of a high prio workqueue instead.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20241211154035.75565-5-frederic@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the proper API instead of open coding it.
However it looks like bnx2fc_percpu_io_thread() kthread could be replaced
by the use of a high prio workqueue instead.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20241211154035.75565-4-frederic@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
BLK_MQ_F_SHOULD_MERGE is set for all tag_sets except those that purely
process passthrough commands (bsg-lib, ufs tmf, various nvme admin
queues) and thus don't even check the flag. Remove it to simplify the
driver interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241219060214.1928848-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace all users of blk_mq_virtio_map_queues with the more generic
blk_mq_map_hw_queues. This in preparation to retire
blk_mq_virtio_map_queues.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Link: https://lore.kernel.org/r/20241202-refactor-blk-affinity-helpers-v6-7-27211e9c2cd5@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace all users of blk_mq_pci_map_queues with the more generic
blk_mq_map_hw_queues. This in preparation to retire
blk_mq_pci_map_queues.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Link: https://lore.kernel.org/r/20241202-refactor-blk-affinity-helpers-v6-5-27211e9c2cd5@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add support for sending user-meta buffer. Set tags to be checked
using flags specified by user/block-layer.
With this change, BIP_CTRL_NOCHECK becomes unused. Remove it.
Signed-off-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241128112240.8867-10-anuj20.g@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We intend to remove the cxlflash driver in an upcoming release. It is
already marked as Obsolete in MAINTAINERS.
The cxlflash driver has received minimal maintenance for some time, and
the CAPI Flash hardware that uses it is no longer commercially available.
Add a warning message on probe and change Kconfig to label the driver as
deprecated and not build the driver by default.
Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20241210054055.144813-3-ajd@linux.ibm.com
'struct pci_device_id' is not modified in these drivers.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
70237 9137 320 79694 1374e drivers/scsi/3w-9xxx.o
After:
=====
text data bss dec hex filename
70461 8913 320 79694 1374e drivers/scsi/3w-9xxx.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/fc61b1946488c1ea8f7a17a06cf40fbd05dcc6de.1733590049.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code allocates the stor_chns array with size num_possible_cpus().
This code assumes cpu_possible_mask is dense, which is not true in the
general case per [1]. If cpu_possible_mask is sparse, the array might be
indexed by a value beyond the size of the array.
However, the configurations that Hyper-V provides to guest VMs on x86 and
ARM64 hardware, in combination with how architecture specific code assigns
Linux CPU numbers, *does* always produce a dense cpu_possible_mask. So the
dense assumption is not currently causing failures. But for robustness
against future changes in how cpu_possible_mask is populated, update the
code to no longer assume dense.
The correct approach is to allocate and initialize the array using size
"nr_cpu_ids". While this leaves unused array entries corresponding to holes
in cpu_possible_mask, the holes are assumed to be minimal and hence the
amount of memory wasted by unused entries is minimal.
[1] https://lore.kernel.org/lkml/SN6PR02MB4157210CC36B2593F8572E5ED4692@SN6PR02MB4157.namprd02.prod.outlook.com/
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20241003035333.49261-5-mhklinux@outlook.com
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_mid_low_api.rst refers to scsi_register() and scsi_unregister() but
these functions don't exist. They have been replaced by more meaningful
names.
Update one driver (megaraid_mbox.c) that uses "scsi_unregister" in a
warning message. Update scsi_mid_low_api.rst to eliminate references to
scsi_register() and scsi_unregister().
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20241205041839.164404-1-rdunlap@infradead.org
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Cc: megaraidlinux.pdl@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche <bvanassche@acm.org> says:
Hi Martin,
The text "slave_" in multiple function names does not make it clear what
the purpose of these functions is. Hence this patch series that renames all
SCSI functions that have the word "slave" in their function name. Please
consider this patch series for the next merge window.
Thanks,
Bart.
Link: https://lore.kernel.org/r/20241022180839.2712439-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that all SCSI drivers have been converted from .slave_configure() to
.sdev_configure(), remove support for .slave_configure() from the SCSI
core.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-5-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The only difference between the .sdev_configure() and .slave_configure()
methods is that the former accepts an additional 'limits' argument.
Convert all SCSI drivers that define a .slave_configure() method to
.sdev_configure(). This patch prepares for removing the
.slave_configure() method. No functionality has been changed.
Acked-by: Geoff Levand <geoff@infradead.org> # for ps3rom
Acked-by: Khalid Aziz <khalid@gonehiking.org> # for the BusLogic driver
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-4-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Improve naming consistency with the .sdev_prep() and .sdev_destroy()
methods by renaming .device_configure() into .sdev_configure().
Cc: Christoph Hellwig <hch@lst.de>
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-3-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename .slave_alloc() into .sdev_init() and .slave_destroy() into
.sdev_destroy(). The new names make it clear that these are actions on
SCSI devices. Make this change in the SCSI core, SCSI drivers and also
in the ATA drivers. No functionality has been changed.
This patch has been created as follows:
* Change the text "slave_alloc" into "sdev_init" in all source files
except those in drivers/net/ and Documentation/.
* Change the text "slave_destroy" into "sdev_destroy" in all source
files except those in drivers/net/ and Documentation/.
* Rename lpfc_no_slave() into lpfc_no_sdev().
* Manually adjust whitespace where necessary to restore vertical
alignment (dc395x driver and include/linux/libata.h).
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Improves the debugging capabilities of the driver by adding more context to
debug messages:
1. Introduce a new function to show pending commands.
2. Include the tag number in NCQ EH path debug messages.
3. Add logging for ata_tag along with pm80xx tag to map I/Os aborted with
ATA logs.
Signed-off-by: Vishakha Channapattan <vishakhavc@google.com>
Signed-off-by: Salomon Dushimirimana <salomondush@google.com>
Link: https://lore.kernel.org/r/20241126225546.975441-1-salomondush@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Increase the number of reserved tags to prevent command processing failures
when the driver is under stress. 8 reserved tags are quickly getting all
used up leading to errors when command completions are delayed.
The driver needs ~512 ccbs/tags for maximum I/O utilization:
16 (max disks) * 32 (max SATA queue depth) = ~512 ccbs/tags.
By reserving 128 tags the driver will still have plenty of tags/ccbs left:
1024 (max ccbs) - 128 (reserved slot) = 896 tags/ccbs left.
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Salomon Dushimirimana <salomondush@google.com>
Link: https://lore.kernel.org/r/20241126224923.973528-1-salomondush@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Other commands were not aware if tag 0x01 was in use or not which meant
multiple commands could share the same tag number.
Prevent tag 0x01 from being used by multiple commands at the same time.
Signed-off-by: Jolly Shah <jollys@google.com>
Signed-off-by: Terrence Adams <tadamsjr@google.com>
Link: https://lore.kernel.org/r/20241125213343.3272478-1-tadamsjr@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
libsas port IDs can differ from the controller's port IDs. Using libsas
port ID to index pm8001_ha->port array is a bug.
Remove sas_find_local_port_id(). We can use pm8001_ha->phy[phy_id].port to
get the port ID.
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Terrence Adams <tadamsjr@google.com>
Link: https://lore.kernel.org/r/20241121194915.3039073-1-tadamsjr@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since commit 771f712ba5 ("scsi: scsi_debug: Fix cmd duration
calculation"), ns_from_boot value is only evaluated in schedule_resp()
for polled requests.
However, ns_from_boot is also required for hrtimer support for when
ndelay is less than INCLUSIVE_TIMING_MAX_NS, so fix up the logic to
decide when to evaluate ns_from_boot.
Fixes: 771f712ba5 ("scsi: scsi_debug: Fix cmd duration calculation")
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20241202130045.2335194-1-john.g.garry@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This partially reverts commit 812fe6420a ("scsi: storvsc: Handle
additional SRB status values").
HyperV does not support MAINTENANCE_IN resulting in FC passthrough
returning the SRB_STATUS_DATA_OVERRUN value. Now that
SRB_STATUS_DATA_OVERRUN is treated as an error, multipath ALUA paths go
into a faulty state as multipath ALUA submits RTPG commands via
MAINTENANCE_IN.
[ 3.215560] hv_storvsc 1d69d403-9692-4460-89f9-a8cbcc0f94f3:
tag#230 cmd 0xa3 status: scsi 0x0 srb 0x12 hv 0xc0000001
[ 3.215572] scsi 1:0:0:32: alua: rtpg failed, result 458752
Make MAINTENANCE_IN return success to avoid the error path as is
currently done with INQUIRY and MODE_SENSE.
Suggested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Cathy Avery <cavery@redhat.com>
Link: https://lore.kernel.org/r/20241127181324.3318443-1-cavery@redhat.com
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix a use-after-free bug in sg_release(), detected by syzbot with KASAN:
BUG: KASAN: slab-use-after-free in lock_release+0x151/0xa30
kernel/locking/lockdep.c:5838
__mutex_unlock_slowpath+0xe2/0x750 kernel/locking/mutex.c:912
sg_release+0x1f4/0x2e0 drivers/scsi/sg.c:407
In sg_release(), the function kref_put(&sfp->f_ref, sg_remove_sfp) is
called before releasing the open_rel_lock mutex. The kref_put() call may
decrement the reference count of sfp to zero, triggering its cleanup
through sg_remove_sfp(). This cleanup includes scheduling deferred work
via sg_remove_sfp_usercontext(), which ultimately frees sfp.
After kref_put(), sg_release() continues to unlock open_rel_lock and may
reference sfp or sdp. If sfp has already been freed, this results in a
slab-use-after-free error.
Move the kref_put(&sfp->f_ref, sg_remove_sfp) call after unlocking the
open_rel_lock mutex. This ensures:
- No references to sfp or sdp occur after the reference count is
decremented.
- Cleanup functions such as sg_remove_sfp() and
sg_remove_sfp_usercontext() can safely execute without impacting the
mutex handling in sg_release().
The fix has been tested and validated by syzbot. This patch closes the
bug reported at the following syzkaller link and ensures proper
sequencing of resource cleanup and mutex operations, eliminating the
risk of use-after-free errors in sg_release().
Reported-by: syzbot+7efb5850a17ba6ce098b@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=7efb5850a17ba6ce098b
Tested-by: syzbot+7efb5850a17ba6ce098b@syzkaller.appspotmail.com
Fixes: cc833acbee ("sg: O_EXCL and other lock handling")
Signed-off-by: Suraj Sonawane <surajsonawane0215@gmail.com>
Link: https://lore.kernel.org/r/20241120125944.88095-1-surajsonawane0215@gmail.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The fc_function_template for vports was missing the
.show_host_supported_speeds. The base port had the same.
Add .show_host_supported_speeds to the vport template as well.
Cc: stable@vger.kernel.org
Fixes: 2c3dfe3f6a ("[SCSI] qla2xxx: add support for NPIV")
Signed-off-by: Anil Gurumurthy <agurumurthy@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20241115130313.46826-7-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVMe controller fails to send connect command due to failure to locate
hw context buffer for NVMe queue 0 (blk_mq_hw_ctx, hctx_idx=0). The
cause of the issue is NPIV host did not initialize the vha->irq_offset
field. This field is given to blk-mq (blk_mq_pci_map_queues) to help
locate the beginning of IO Queues which in turn help locate NVMe queue
0.
Initialize this field to allow NVMe to work properly with NPIV host.
kernel: nvme nvme5: Connect command failed, errno: -18
kernel: nvme nvme5: qid 0: secure concatenation is not supported
kernel: nvme nvme5: NVME-FC{5}: create_assoc failed, assoc_id 2e9100 ret 401
kernel: nvme nvme5: NVME-FC{5}: reset: Reconnect attempt failed (401)
kernel: nvme nvme5: NVME-FC{5}: Reconnect attempt in 2 seconds
Cc: stable@vger.kernel.org
Fixes: f0783d43dd ("scsi: qla2xxx: Use correct number of vectors for online CPUs")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20241115130313.46826-6-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware supports multiple sg_cnt for request and response for CT
commands, so remove the redundant check. A check is there where sg_cnt
for request and response should be same. This is not required as driver
and FW have code to handle multiple and different sg_cnt on request and
response.
Cc: stable@vger.kernel.org
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20241115130313.46826-5-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently FCE Tracing is enabled to log additional ELS events. Instead,
user will enable or disable this feature through debugfs.
Modify existing DFS knob to allow user to enable or disable this
feature.
echo [1 | 0] > /sys/kernel/debug/qla2xxx/qla2xxx_??/fce
cat /sys/kernel/debug/qla2xxx/qla2xxx_??/fce
Cc: stable@vger.kernel.org
Fixes: df613b9607 ("[SCSI] qla2xxx: Add Fibre Channel Event (FCE) tracing support.")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20241115130313.46826-4-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use vcalloc() instead of vmalloc() followed by memset(0) to simplify the
functions fnic_trace_buf_init() and fnic_fc_trace_init().
Compile-tested only.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Link: https://lore.kernel.org/r/20241107104300.1252-1-thorsten.blum@linux.dev
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
System crash is observed with stack trace warning of use after
free. There are 2 signals to tell dpc_thread to terminate (UNLOADING
flag and kthread_stop).
On setting the UNLOADING flag when dpc_thread happens to run at the time
and sees the flag, this causes dpc_thread to exit and clean up
itself. When kthread_stop is called for final cleanup, this causes use
after free.
Remove UNLOADING signal to terminate dpc_thread. Use the kthread_stop
as the main signal to exit dpc_thread.
[596663.812935] kernel BUG at mm/slub.c:294!
[596663.812950] invalid opcode: 0000 [#1] SMP PTI
[596663.812957] CPU: 13 PID: 1475935 Comm: rmmod Kdump: loaded Tainted: G IOE --------- - - 4.18.0-240.el8.x86_64 #1
[596663.812960] Hardware name: HP ProLiant DL380p Gen8, BIOS P70 08/20/2012
[596663.812974] RIP: 0010:__slab_free+0x17d/0x360
...
[596663.813008] Call Trace:
[596663.813022] ? __dentry_kill+0x121/0x170
[596663.813030] ? _cond_resched+0x15/0x30
[596663.813034] ? _cond_resched+0x15/0x30
[596663.813039] ? wait_for_completion+0x35/0x190
[596663.813048] ? try_to_wake_up+0x63/0x540
[596663.813055] free_task+0x5a/0x60
[596663.813061] kthread_stop+0xf3/0x100
[596663.813103] qla2x00_remove_one+0x284/0x440 [qla2xxx]
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20241115130313.46826-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before retrying initialization, check and abort if the fault code
indicates insufficient power. Also mark the controller as unrecoverable
instead of issuing reset in the watch dog timer if the fault code
indicates insufficient power.
Signed-off-by: Prayas Patel <prayas.patel@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241110194405.10108-5-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of displaying the controller index starting from '1' make the
driver display the controller index starting from '0'.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241110194405.10108-4-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver, through the SAS transport, exposes a sysfs interface to
enable/disable PHYs in a controller/expander setup. When multiple PHYs
are disabled and enabled in rapid succession, the persistent and current
config pages related to SAS IO unit/SAS Expander pages could get
corrupted.
Use separate memory for each config request.
Signed-off-by: Prayas Patel <prayas.patel@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241110194405.10108-3-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver serializes ioctls through a mutex lock but access to the
ioctl data buffer is not guarded by the mutex. This results in multiple
user threads being able to write to the driver's ioctl buffer
simultaneously.
Protect the ioctl buffer with the ioctl mutex.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241110194405.10108-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the 2 simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups that
can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog
As mentioned above, there is 2 merge conflicts with your tree, one is
where the file is removed (easy enough to resolve), the second is a
build time error, that has been found in linux-next and the fix can be
seen here:
https://lore.kernel.org/r/20241107212645.41252436@canb.auug.org.au
Other than that, the changes here have been in linux-next with no other
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ0lEog8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym+0ACgw6wN+LkLVIHWhxTq5DYHQ0QCxY8AoJrRIcKe
78h0+OU3OXhOy8JGz62W
=oI5S
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the two simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups
that can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog"
* tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (35 commits)
Fix a potential abuse of seq_printf() format string in drivers
cpu: Remove spurious NULL in attribute_group definition
s390/con3215: Remove spurious NULL in attribute_group definition
perf: arm-ni: Remove spurious NULL in attribute_group definition
driver core: Constify bin_attribute definitions
sysfs: attribute_group: allow registration of const bin_attribute
firmware_loader: Fix possible resource leak in fw_log_firmware_info()
drivers: core: fw_devlink: Fix excess parameter description in docstring
driver core: class: Correct WARN() message in APIs class_(for_each|find)_device()
cacheinfo: Use of_property_present() for non-boolean properties
cdx: Fix cdx_mmap_resource() after constifying attr in ->mmap()
drivers: core: fw_devlink: Make the error message a bit more useful
phy: tegra: xusb: Set fwnode for xusb port devices
drm: display: Set fwnode for aux bus devices
driver core: fw_devlink: Stop trying to optimize cycle detection logic
driver core: Constify attribute arguments of binary attributes
sysfs: bin_attribute: add const read/write callback variants
sysfs: implement all BIN_ATTR_* macros in terms of __BIN_ATTR()
sysfs: treewide: constify attribute callback of bin_attribute::llseek()
sysfs: treewide: constify attribute callback of bin_attribute::mmap()
...
Updates to the usual drivers (ufs, lpfc, hisi_sas, st). Amazingly
enough, no core changes with the biggest set of driver changes being
ufs (which conflicted with it's own fixes a bit, hence the merges) and
the rest being minor fixes and updates.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZ0SFmyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdA6AQC+yzhe
jx0+EBw1RkjRoT6vapBsjN8Sc1rOr/8+TuJ8KwEA0eVuXSiFEx/ieeKLD2VuE6y4
NPRB36MZdOxfQaDZAY4=
=Fj/G
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, hisi_sas, st).
Amazingly enough, no core changes with the biggest set of driver
changes being ufs (which conflicted with it's own fixes a bit, hence
the merges) and the rest being minor fixes and updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (97 commits)
scsi: st: New session only when Unit Attention for new tape
scsi: st: Add MTIOCGET and MTLOAD to ioctls allowed after device reset
scsi: st: Don't modify unknown block number in MTIOCGET
scsi: ufs: core: Restore SM8650 support
scsi: sun3: Mark driver struct with __refdata to prevent section mismatch
scsi: sg: Enable runtime power management
scsi: qedi: Fix a possible memory leak in qedi_alloc_and_init_sb()
scsi: qedf: Fix a possible memory leak in qedf_alloc_and_init_sb()
scsi: fusion: Remove unused variable 'rc'
scsi: bfa: Fix use-after-free in bfad_im_module_exit()
scsi: esas2r: Remove unused esas2r_build_cli_req()
scsi: target: Fix incorrect function name in pscsi_create_type_disk()
scsi: ufs: Replace deprecated PCI functions
scsi: Switch back to struct platform_driver::remove()
scsi: pm8001: Increase request sg length to support 4MiB requests
scsi: pm8001: Initialize devices in pm8001_alloc_dev()
scsi: pm8001: Use module param to set pcs event log severity
scsi: ufs: ufs-mediatek: Configure individual LU queue flags
scsi: MAINTAINERS: Update UFS Exynos entry
scsi: lpfc: Copyright updates for 14.4.0.6 patches
...
This fixes a 'possible circular locking dependency detected' warning
CPU0 CPU1
---- ----
lock(&instance->reset_mutex);
lock(&shost->scan_mutex);
lock(&instance->reset_mutex);
lock(&shost->scan_mutex);
Fix this by temporarily releasing the reset_mutex.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Link: https://lore.kernel.org/r/20240923174833.45345-1-thenzl@redhat.com
Acked-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
bfa has a set of structure parsers, of which quite a few are unused.
Remove the unused set.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20241117135215.38771-3-linux@treblig.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
bfa has a large set of structure builders, of which only about 60% are
used; remove the rest.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20241117135215.38771-2-linux@treblig.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the hardware revision numbering for Qlogic ISP1020/1040 boards. HWMASK
suggests that the revision number only needs four bits, this is consistent
with how NetBSD does things in their ISP driver. Verified on a IPS1040B
which is seen as rev 5 not as BIT_4.
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20241113225636.2276-1-linmag7@gmail.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Tree wide:
* Make nr_irqs static to the core code and provide accessor functions
to remove existing and prevent future aliasing problems with local
variables or function arguments of the same name.
- Core code:
* Prevent freeing an interrupt in the devres code which is not managed
by devres in the first place.
* Use seq_put_decimal_ull_width() for decimal values output in
/proc/interrupts which increases performance significantly as it
avoids parsing the format strings over and over.
* Optimize raising the timer and hrtimer soft interrupts by using the
'set bit only' variants instead of the combined version which checks
whether ksoftirqd should be woken up. The latter is a pointless
exercise as both soft interrupts are raised in the context of the
timer interrupt and therefore never wake up ksoftirqd.
* Delegate timer/hrtimer soft interrupt processing to a dedicated thread
on RT.
Timer and hrtimer soft interrupts are always processed in ksoftirqd
on RT enabled kernels. This can lead to high latencies when other
soft interrupts are delegated to ksoftirqd as well.
The separate thread allows to run them seperately under a RT
scheduling policy to reduce the latency overhead.
- Drivers:
* New drivers or extensions of existing drivers to support Renesas
RZ/V2H(P), Aspeed AST27XX, T-HEAD C900 and ATMEL sam9x7 interrupt
chips
* Support for multi-cluster GICs on MIPS.
MIPS CPUs can come with multiple CPU clusters, where each CPU cluster
has its own GIC (Generic Interrupt Controller). This requires to
access the GIC of a remote cluster through a redirect register block.
This is encapsulated into a set of helper functions to keep the
complexity out of the actual code paths which handle the GIC details.
* Support for encrypted guests in the ARM GICV3 ITS driver
The ITS page needs to be shared with the hypervisor and therefore
must be decrypted.
* Small cleanups and fixes all over the place
-----BEGIN PGP SIGNATURE-----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=JqxC
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2024-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt subsystem updates from Thomas Gleixner:
"Tree wide:
- Make nr_irqs static to the core code and provide accessor functions
to remove existing and prevent future aliasing problems with local
variables or function arguments of the same name.
Core code:
- Prevent freeing an interrupt in the devres code which is not
managed by devres in the first place.
- Use seq_put_decimal_ull_width() for decimal values output in
/proc/interrupts which increases performance significantly as it
avoids parsing the format strings over and over.
- Optimize raising the timer and hrtimer soft interrupts by using the
'set bit only' variants instead of the combined version which
checks whether ksoftirqd should be woken up. The latter is a
pointless exercise as both soft interrupts are raised in the
context of the timer interrupt and therefore never wake up
ksoftirqd.
- Delegate timer/hrtimer soft interrupt processing to a dedicated
thread on RT.
Timer and hrtimer soft interrupts are always processed in ksoftirqd
on RT enabled kernels. This can lead to high latencies when other
soft interrupts are delegated to ksoftirqd as well.
The separate thread allows to run them seperately under a RT
scheduling policy to reduce the latency overhead.
Drivers:
- New drivers or extensions of existing drivers to support Renesas
RZ/V2H(P), Aspeed AST27XX, T-HEAD C900 and ATMEL sam9x7 interrupt
chips
- Support for multi-cluster GICs on MIPS.
MIPS CPUs can come with multiple CPU clusters, where each CPU
cluster has its own GIC (Generic Interrupt Controller). This
requires to access the GIC of a remote cluster through a redirect
register block.
This is encapsulated into a set of helper functions to keep the
complexity out of the actual code paths which handle the GIC
details.
- Support for encrypted guests in the ARM GICV3 ITS driver
The ITS page needs to be shared with the hypervisor and therefore
must be decrypted.
- Small cleanups and fixes all over the place"
* tag 'irq-core-2024-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
irqchip/riscv-aplic: Prevent crash when MSI domain is missing
genirq/proc: Use seq_put_decimal_ull_width() for decimal values
softirq: Use a dedicated thread for timer wakeups on PREEMPT_RT.
timers: Use __raise_softirq_irqoff() to raise the softirq.
hrtimer: Use __raise_softirq_irqoff() to raise the softirq
riscv: defconfig: Enable T-HEAD C900 ACLINT SSWI drivers
irqchip: Add T-HEAD C900 ACLINT SSWI driver
dt-bindings: interrupt-controller: Add T-HEAD C900 ACLINT SSWI device
irqchip/stm32mp-exti: Use of_property_present() for non-boolean properties
irqchip/mips-gic: Fix selection of GENERIC_IRQ_EFFECTIVE_AFF_MASK
irqchip/mips-gic: Prevent indirect access to clusters without CPU cores
irqchip/mips-gic: Multi-cluster support
irqchip/mips-gic: Setup defaults in each cluster
irqchip/mips-gic: Support multi-cluster in for_each_online_cpu_gic()
irqchip/mips-gic: Replace open coded online CPU iterations
genirq/irqdesc: Use str_enabled_disabled() helper in wakeup_show()
genirq/devres: Don't free interrupt which is not managed by devres
irqchip/gic-v3-its: Fix over allocation in itt_alloc_pool()
irqchip/aspeed-intc: Add AST27XX INTC support
dt-bindings: interrupt-controller: Add support for ASPEED AST27XX INTC
...
-----BEGIN PGP SIGNATURE-----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=PWTH
-----END PGP SIGNATURE-----
Merge tag 'for-6.13/block-20241118' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe updates via Keith:
- Use uring_cmd helper (Pavel)
- Host Memory Buffer allocation enhancements (Christoph)
- Target persistent reservation support (Guixin)
- Persistent reservation tracing (Guixen)
- NVMe 2.1 specification support (Keith)
- Rotational Meta Support (Matias, Wang, Keith)
- Volatile cache detection enhancment (Guixen)
- MD updates via Song:
- Maintainers update
- raid5 sync IO fix
- Enhance handling of faulty and blocked devices
- raid5-ppl atomic improvement
- md-bitmap fix
- Support for manually defining embedded partition tables
- Zone append fixes and cleanups
- Stop sending the queued requests in the plug list to the driver
->queue_rqs() handle in reverse order.
- Zoned write plug cleanups
- Cleanups disk stats tracking and add support for disk stats for
passthrough IO
- Add preparatory support for file system atomic writes
- Add lockdep support for queue freezing. Already found a bunch of
issues, and some fixes for that are in here. More will be coming.
- Fix race between queue stopping/quiescing and IO queueing
- ublk recovery improvements
- Fix ublk mmap for 64k pages
- Various fixes and cleanups
* tag 'for-6.13/block-20241118' of git://git.kernel.dk/linux: (118 commits)
MAINTAINERS: Update git tree for mdraid subsystem
block: make struct rq_list available for !CONFIG_BLOCK
block/genhd: use seq_put_decimal_ull for diskstats decimal values
block: don't reorder requests in blk_mq_add_to_batch
block: don't reorder requests in blk_add_rq_to_plug
block: add a rq_list type
block: remove rq_list_move
virtio_blk: reverse request order in virtio_queue_rqs
nvme-pci: reverse request order in nvme_queue_rqs
btrfs: validate queue limits
block: export blk_validate_limits
nvmet: add tracing of reservation commands
nvme: parse reservation commands's action and rtype to string
nvmet: report ns's vwc not present
md/raid5: Increase r5conf.cache_name size
block: remove the ioprio field from struct request
block: remove the write_hint field from struct request
nvme: check ns's volatile write cache not present
nvme: add rotational support
nvme: use command set independent id ns if available
...
The write_hint is only used for read/write requests, which must have a
bio attached to them. Just use the bio field instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241112170050.1612998-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
max_zone_append_sectors differs from all other queue limits in that the
final value used is not stored in the queue_limits but needs to be
obtained using queue_limits_max_zone_append_sectors helper. This not
only adds (tiny) extra overhead to the I/O path, but also can be easily
forgotten in file system code.
Add a new max_hw_zone_append_sectors value to queue_limits which is
set by the driver, and calculate max_zone_append_sectors from that and
the other inputs in blk_validate_zoned_limits, similar to how
max_sectors is calculated to fix this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241104073955.112324-3-hch@lst.de
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20241108154657.845768-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Two small fixes, the drivers one in ufs simply delays running a work
queue and the generic one in zoned storage switches to a more correct
API that tries the standard buddy allocator first (for small
allocations); this fixes an allocation problem with small allocations
seen under memory pressure.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZy5pZSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdonAQCeHKnp
BkxbSls2uPQn4DAxak1tCfxTujMFWxQHP2Y92gEA2q3chF7P136z2rYp0wGfm7P4
ivxddAWZth4tV7TUUw8=
=by5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes, the drivers one in ufs simply delays running a work
queue and the generic one in zoned storage switches to a more correct
API that tries the standard buddy allocator first (for small
allocations); this fixes an allocation problem with small allocations
seen under memory pressure"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Start the RTC update work later
scsi: sd_zbc: Use kvzalloc() to allocate REPORT ZONES buffer
Kai Mäkisara <Kai.Makisara@kolumbus.fi> says:
These three patches were developed in response to Bugzilla report
https://bugzilla.kernel.org/show_bug.cgi?id=219419
After device reset, the tape driver allows only operations that don't
write or read anything from tape. The reason for this is that many
(most ?) drives rewind the tape after reset and the subsequent reads
or writes would not be at the tape location the user expects. Reading
and writing is allowed again when the user does something to position the
tape (e.g., rewind).
The Bugzilla report considers the case when a user, after reset, tries
to read the drive status with MTIOCGET ioctl, but it fails. MTIOCGET
does not return much useful data after reset, but it can be allowed.
MTLOAD positions the tape and it should be allowed. The second patch
adds these to the set of allowed operations after device reset.
The first patch fixes a bug seen when developing the second patch.
V2: The third patch is added to fix a bug that resulted in not
blocking writes if reset occurs while the device file is not open.
Link: https://lore.kernel.org/r/20241106095723.63254-1-Kai.Makisara@kolumbus.fi
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the code starts new tape session when any Unit Attention
(UA) is seen when opening the device. This leads to incorrectly
clearing pos_unknown when the UA is for reset. Set new session only
when the UA is for a new tape.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://lore.kernel.org/r/20241106095723.63254-4-Kai.Makisara@kolumbus.fi
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Tested-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most drives rewind the tape when the device is reset. Reading and writing
are not allowed until something is done to make the tape position match the
user's expectation (e.g., rewind the tape). Add MTIOCGET and MTLOAD to
operations allowed after reset. MTIOCGET is modified to not touch the tape
if pos_unknown is non-zero. The tape location is known after MTLOAD.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219419#c14
Link: https://lore.kernel.org/r/20241106095723.63254-3-Kai.Makisara@kolumbus.fi
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Tested-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As described in the added code comment, a reference to .exit.text is ok
for drivers registered via module_platform_driver_probe(). Make this
explicit to prevent the following section mismatch warnings
WARNING: modpost: drivers/scsi/sun3_scsi: section mismatch in reference: sun3_scsi_driver+0x4 (section: .data) -> sun3_scsi_remove (section: .exit.text)
WARNING: modpost: drivers/scsi/sun3_scsi_vme: section mismatch in reference: sun3_scsi_driver+0x4 (section: .data) -> sun3_scsi_remove (section: .exit.text)
that trigger on a Sun 3 allmodconfig build.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/b2c56fa3556505befe9b4cb9a830d9e2a962e72c.1730831769.git.geert@linux-m68k.org
Acked-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In 2010, runtime power management support was implemented in the SCSI
core. The description of patch "[SCSI] implement runtime Power
Management" mentions that the sg driver is skipped but not why. This
patch enables runtime power management even if an instance of the sg
driver is held open. Enabling runtime PM for the sg driver is safe
because all interactions of the sg driver with the SCSI device pass
through the block layer (blk_execute_rq_nowait()) and the block layer
already supports runtime PM.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Fixes: bc4f24014d ("[SCSI] implement runtime Power Management")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241030220310.1373569-1-bvanassche@acm.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hook "qedi_ops->common->sb_init = qed_sb_init" does not release the DMA
memory sb_virt when it fails. Add dma_free_coherent() to free it. This
is the same way as qedr_alloc_mem_sb() and qede_alloc_mem_sb().
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20241026125711.484-3-thunder.leizhen@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hook "qed_ops->common->sb_init = qed_sb_init" does not release the DMA
memory sb_virt when it fails. Add dma_free_coherent() to free it. This
is the same way as qedr_alloc_mem_sb() and qede_alloc_mem_sb().
Fixes: 61d8658b4a ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.")
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20241026125711.484-2-thunder.leizhen@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
esas2r_build_cli_req() has been unused since it was added in 2013 by
commit 26780d9e12 ("[SCSI] esas2r: ATTO Technology ExpressSAS 6G
SAS/SATA RAID Adapter Driver")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20241102220336.80541-1-linux@treblig.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/scsi to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
On the way do a few whitespace changes to make indention consistent.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241028080754.429191-2-u.kleine-koenig@baylibre.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Increasing the per-request size maximum to 4MiB (8192 sectors x 512
bytes) runs into the per-device DMA scatter gather list limit
(max_segments) for users of the io vector system calls (e.g. readv and
writev).
Increase the max scatter gather list length to 1024 to enable kernel to
send 4MiB (1024 * 4KiB page size) requests.
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20241025185009.3278297-1-ipylypiv@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Devices can be allocated and freed at runtime. For example during a soft
reset all devices are freed and reallocated upon discovery.
Currently the driver fully initializes devices once in pm8001_alloc().
Allows initialization steps to happen during runtime, avoiding any
leftover states from the device being freed.
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Terrence Adams <tadamsjr@google.com>
Link: https://lore.kernel.org/r/20241021201828.1378858-1-tadamsjr@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The pm8001 driver sets pcs event log threshold very high which causes
most of the FW log messages to not be captured. Add a module parameter
to configure pcs event log severity with 3 (medium severity) as the
default.
Co-developed-by: Bhavesh Jashnani <bjashnani@google.com>
Signed-off-by: Bhavesh Jashnani <bjashnani@google.com>
Signed-off-by: Salomon Dushimirimana <salomondush@google.com>
Link: https://lore.kernel.org/r/20241016220944.370539-1-salomondush@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Justin Tee <justintee8345@gmail.com> says:
Update lpfc to revision 14.4.0.6
This patch set contains bug fixes related to congestion handling,
accounting for internal remoteport objects, resource release during
HBA unload and reset, and clean up regarding the abuse of a global
spinlock.
The patches were cut against Martin's 6.13/scsi-queue tree.
Link: https://lore.kernel.org/r/20241031223219.152342-1-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The is_bin_visible() callbacks should not modify the struct
bin_attribute passed as argument.
Enforce this by marking the argument as const.
As there are not many callback implementers perform this change
throughout the tree at once.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20241103-sysfs-const-bin_attr-v2-5-71110628844c@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
max_zone_append_sectors differs from all other queue limits in that the
final value used is not stored in the queue_limits but needs to be
obtained using queue_limits_max_zone_append_sectors helper. This not
only adds (tiny) extra overhead to the I/O path, but also can be easily
forgotten in file system code.
Add a new max_hw_zone_append_sectors value to queue_limits which is
set by the driver, and calculate max_zone_append_sectors from that and
the other inputs in blk_validate_zoned_limits, similar to how
max_sectors is calculated to fix this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241104073955.112324-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In attempt to reduce the amount of unnecessary ndlp->lock acquisitions
in the lpfc driver, change nlpa_flag into an unsigned long bitmask and
use clear_bit/test_bit bitwise atomic APIs instead of reliance on
ndlp->lock for synchronization.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241031223219.152342-10-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An RPI is tightly bound to an NDLP structure and is freed only upon
release of an NDLP object. As such, there should be no logic that frees
an RPI outside of the lpfc_nlp_release() routine. In order to reinforce
the original design usage of RPIs, remove the NLP_RELEASE_RPI flag and
related logic.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241031223219.152342-9-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current dev_loss_tmo handling checks whether there has been a previous
call to unregister with SCSI transport. If so, the NDLP kref count is
decremented a second time in dev_loss_tmo as the final kref release.
However, this can sometimes result in a reference count underflow if
there is also a race to unregister with NVMe transport as well. Add a
check for NVMe transport registration before decrementing the final
kref. If NVMe transport is still registered, then the NVMe transport
unregistration is designated as the final kref decrement.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241031223219.152342-8-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An HBA reset request that is executed when there are outstanding NVME-LS
commands can cause delays for the reset process to complete. Fix by
introducing a new routine called lpfc_nvmels_flush_cmd() that walks the
phba->nvmels_wq list and cancels outstanding submitted NVME-LS requests
speeding up the HBA reset process.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241031223219.152342-7-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpfc_cmpl_ct_disc_fdmi() routine has incorrect logic that treats an
FDMI completion with error LOCAL_REJECT/SLI_ABORTED as a success status.
Under the erroneous assumption of successful completion, the routine
proceeds to issue follow up FDMI commands, which may never complete if
the HBA is in an errata state as indicated by the errored completion
status. Fix by freeing FDMI cmd resources and early return when the
LPFC_SLI_ACTIVE flag is not set and a LOCAL_REJECT/SLI_ABORTED or
SLI_DOWN status is received.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241031223219.152342-6-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During firmware errata events, the lpfc_els_flush_cmd() routine is
responsible for the clean up of outstanding ELS and CT command
submissions. Thus, move the LPFC_SLI_ACTIVE flag check into the txcmplq
list walk and mark a piocb object for canceling if determined the HBA is
not active. Clean up should be regardless of application or driver
layer origin.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241031223219.152342-5-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During initialization, the driver allocates wq->pring in lpfc_wq_create
and lpfc_sli4_queue_unset() is the only place where kfree(wq->pring) is
called.
There is a possible memory leak in lpfc_sli_brdrestart_s4() (restart)
and lpfc_pci_remove_one_s4() (rmmod) paths because there are no calls to
lpfc_sli4_queue_unset() to kfree() the wq->pring.
Fix by inserting a call to lpfc_sli4_queue_unset() in
lpfc_sli_brdrestart_s4() and lpfc_sli4_hba_unset() routines. Also, add
a check for the SLI_ACTIVE flag before issuing the Q_DESTROY mailbox
command. If not set, then the mailbox command will obviously fail. In
such cases, skip issuing the mailbox command and only execute the driver
resource clean up portions of the lpfc_*q_destroy routines.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241031223219.152342-4-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Should an rport remain in the NOTPRESENT state it is possible that
stgt_delete_work is scheduled after dev_loss_tmo_callbk. In such cases,
dev_loss_tmo_callbk would have cleaned up the NDLP object resulting in
stale ndlp pointers in lpfc_terminate_rport_io().
Check for the DEVLOSS_CALLBK_DONE flag to know if dev_loss_tmo_callbk
has been called. This is a more reliable way to avoid dereferencing
stale NDLP pointers.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241031223219.152342-3-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CGN warning signals are currently statically fixed to a passed in driver
parameter called lpfc_fabric_cgn_frequency. However, CGN frequency
should be more correctly based on EDC responses from the fabric when
available. Otherwise, still allow the driver to fall back on user
configured lpfc_fabric_cgn_frequency driver parameter.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241031223219.152342-2-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We have two reports of failed memory allocation in btrfs' code which is
calling into report zones.
Both of these reports have the following signature coming from
__vmalloc_area_node():
kworker/u17:5: vmalloc error: size 0, failed to allocate pages, mode:0x10dc2(GFP_KERNEL|__GFP_HIGHMEM|__GFP_NORETRY|__GFP_ZERO), nodemask=(null),cpuset=/,mems_allowed=0
Further debugging showed these where allocations of one sector (512
bytes) and at least one of the reporter's systems where low on memory,
so going through the overhead of allocating a vm area failed.
Switching the allocation from __vmalloc() to kvzalloc() avoids the
overhead of vmalloc() on small allocations and succeeds.
Note: the buffer is already freed using kvfree() so there's no need to
adjust the free path.
Cc: Qu Wenru <wqu@suse.com>
Cc: Naohiro Aota <naohiro.aota@wdc.com>
Link: https://github.com/kdave/btrfs-progs/issues/779
Link: https://github.com/kdave/btrfs-progs/issues/915
Fixes: 23a50861ad ("scsi: sd_zbc: Cleanup sd_zbc_alloc_report_buffer()")
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20241030110253.11718-1-jth@kernel.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Two small fixes, both in drivers (ufs and scsi_debug).
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZyH+cSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishVdMAQDdOiaS
9DO+ly/Il64wXZqb9WKcVYRIjmz7m7g5xdMgrgEA1yfD6G7GgQ3zvbVPNC7Y9ecr
4O2iR5EGAVb1Y7UaEQU=
=551G
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes, both in drivers (ufs and scsi_debug)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Fix another deadlock during RTC update
scsi: scsi_debug: Fix do_device_access() handling of unexpected SG copy length
If the sg_copy_buffer() call returns less than sdebug_sector_size, then
we drop out of the copy loop. However, we still report that we copied
the full expected amount, which is not proper.
Fix by keeping a running total and return that value.
Fixes: 84f3a3c01d ("scsi: scsi_debug: Atomic write support")
Reported-by: Colin Ian King <colin.i.king@gmail.com>
Suggested-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20241018101655.4207-1-john.g.garry@oracle.com
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes all in drivers. The largest is the mpi3mr which corrects a phy
count limit that should only apply to the controller but was being
incorrectly applied to expander phys.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZxQINSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfuiAP9+gxzU
MYpyNFYmS8iwbma+wagKMr2ZxpiIAnQIukBtugD7Baqw7YjNbAPtCcQMgC96y8ac
X7zeMkLTyMqkaIjOQFk=
=eHKZ
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Fixes all in drivers. The largest is the mpi3mr which corrects a phy
count limit that should only apply to the controller but was being
incorrectly applied to expander phys"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: core: Fix null-ptr-deref in target_alloc_device()
scsi: mpi3mr: Validate SAS port assignments
scsi: ufs: core: Set SDEV_OFFLINE when UFS is shut down
scsi: ufs: core: Requeue aborted request
scsi: ufs: core: Fix the issue of ICU failure
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-12-bvanassche@acm.org
Yihang Li <liyihang9@huawei.com> says:
This series contains some fixes including:
- Adjust priority of registering and exiting debugfs for security;
- Create trigger_dump at the end of the debugfs initialization;
- Add firmware information check;
- Enable all PHYs that are not disabled by user during controller reset;
- Reset PHY again if phyup timeout;
- Check usage count only when the runtime PM status is RPM_SUSPENDING;
- Add cond_resched() for no forced preemption model;
- Default enable interrupt coalescing;
- Update disk locked timeout to 7 seconds;
- Add time interval between two H2D FIS following soft reset spec;
- Update v3 hw STP_LINK_TIMER setting;
- Create all dump files during debugfs initialization;
- Add latest_dump for the debugfs dump;
Link: https://lore.kernel.org/r/20241008021822.2617339-1-liyihang9@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before that, after the user triggers the dump, the latest dump
information can be viewed in the directory with the maximum number in
the dump directory.
After this series patch, the driver creates all debugfs directories and
files during initialization. Therefore, users cannot know the directory
where the latest dump information is stored. So, add latest_dump file to
notify users where the latest dump information is stored.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-14-liyihang9@huawei.com
Reviewed-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
At present, it is found that some SATA HDD disks may continue to return
the HOLD primitive for more than 500ms when they are busy writing data,
which is more likely to trigger an STP link timeout exception. Now
Modify STP link timer from 500ms to the maximum value of 1.048575s.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-12-liyihang9@huawei.com
Reviewed-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Spec says at least 5us between two H2D FIS when do soft reset, but be
generous and sleep for about 1ms.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-11-liyihang9@huawei.com
Reviewed-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SATA disk will be locked after the disk sends the DMA Setup frame
until all data frame transmission is completed. The
CFG_ICT_TIMER_STEP_TRSH register is used for sata disk to configure the
step size of the timer which records the time when the disk is
locked. The unit is 1us and the default step size is 150ms. If the disk
is locked for more than 7 timer steps, the io to be sent to the disk
will end abnormally.
The current timeout is only about 1 second, it is easy to trigger IO
abnormal end when the SATA hard disk returns data slowly. Adjust the
timeout to 7 seconds based on ERC time of most disks.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-10-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the current interrupt reporting mode, each CQ entry reports an
interrupt. However, when there are a large number of I/O hardware
completion interrupts, the following issue may occur:
[ 4682.678657][ C129] irq 134: nobody cared (try booting with the "irqpoll" option)
[ 4682.708455][ C129] Call trace:
[ 4682.711589][ C129] dump_backtrace+0x0/0x1e4
[ 4682.715934][ C129] show_stack+0x20/0x2c
[ 4682.719933][ C129] dump_stack+0xd8/0x140
[ 4682.724017][ C129] __report_bad_irq+0x54/0x180
[ 4682.728625][ C129] note_interrupt+0x1ec/0x2f0
[ 4682.733143][ C129] handle_irq_event+0x118/0x1ac
[ 4682.737834][ C129] handle_fasteoi_irq+0xc8/0x200
[ 4682.742613][ C129] __handle_domain_irq+0x84/0xf0
[ 4682.747391][ C129] gic_handle_irq+0x88/0x2c0
[ 4682.751822][ C129] el1_irq+0xbc/0x140
[ 4682.755648][ C129] _find_next_bit.constprop.0+0x20/0x94
[ 4682.761036][ C129] cpumask_next+0x24/0x30
[ 4682.765208][ C129] gic_ipi_send_mask+0x48/0x170
[ 4682.769900][ C129] __ipi_send_mask+0x34/0x110
[ 4682.775720][ C129] smp_cross_call+0x3c/0xcc
[ 4682.780064][ C129] arch_send_call_function_single_ipi+0x38/0x44
[ 4682.786146][ C129] send_call_function_single_ipi+0xd0/0xe0
[ 4682.791794][ C129] generic_exec_single+0xb4/0x170
[ 4682.796659][ C129] smp_call_function_single_async+0x2c/0x40
[ 4682.802395][ C129] blk_mq_complete_request_remote.part.0+0xec/0x100
[ 4682.808822][ C129] blk_mq_complete_request+0x30/0x70
[ 4682.813950][ C129] scsi_mq_done+0x48/0xac
[ 4682.818128][ C129] sas_scsi_task_done+0xb0/0x150 [libsas]
[ 4682.823692][ C129] slot_complete_v3_hw+0x230/0x710 [hisi_sas_v3_hw]
[ 4682.830120][ C129] cq_thread_v3_hw+0xbc/0x190 [hisi_sas_v3_hw]
[ 4682.836114][ C129] irq_thread_fn+0x34/0xa4
[ 4682.840371][ C129] irq_thread+0xc4/0x130
[ 4682.844455][ C129] kthread+0x108/0x13c
[ 4682.848365][ C129] ret_from_fork+0x10/0x18
[ 4682.852621][ C129] handlers:
[ 4682.855577][ C129] [<00000000949e52bf>] cq_interrupt_v3_hw [hisi_sas_v3_hw] threaded [<000000005d8e3b68>] cq_thread_v3_hw [hisi_sas_v3_hw]
[ 4682.868084][ C129] Disabling IRQ #134
When the IRQ management layer processes each hardware interrupt, if the
return value of the interrupt handler is IRQ_WAKE_THREAD, it will wake
up the handler thread for this interrupt action and set IRQTF_RUNTHREAD
flag, wait for the interrupt handling thread to clear the
IRQTF_RUNTHREAD flag after execution. Later in note_interrupt(), use
irq_count to count hardware interrupts and irqs_unhandled to count
interrupts for which no thread handler is responsible. When irq_count
reaches 100000 and irqs_unhandled reaches 99000, irq will be disabled.
In the performance test scenario, I/O completion hardware interrupts are
continuously and quickly generated. As a result, the interrupt
processing thread is cyclically called in irq_thread() and does not
exit, this affects the response of the interrupt thread to the hardware
interrupt and causes irqs_unhandled to grow to 99000. Finally, the irq
is disabled.
Therefore, default enable interrupt coalescing to reduce the generation
of hardware interrupts, this helps interrupt processing threads to stop
calling in irq_thread().
For interrupt coalescing, according to the actual performance test, set
the count of CQ entries to 10 and the interrupt coalescing timeout
period to 10us based on the actual performance test.
Before and after interrupt coalescing is enabled, the 4K read/write
performance is improved by about 3%, and the 256K read/write performance
is basically the same.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-9-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Users can suspend the machine with 'echo disk > /sys/power/state', but
the suspend will fail because the SAS controller cannot be suspended:
[root@localhost ~]# echo freeze > /sys/power/state
-bash: echo: write error: Device or resource busy
[15104.142955] PM: suspend entry (s2idle)
...
[15104.283465] hisi_sas_v3_hw 0000:32:04.0: entering suspend state
[15104.283480] hisi_sas_v3_hw 0000:30:04.0: entering suspend state
[15104.283500] hisi_sas_v3_hw 0000:32:04.0: PM suspend: host status cannot be suspended
[15104.283508] hisi_sas_v3_hw 0000:30:04.0: PM suspend: host status cannot be suspended
[15104.283516] hisi_sas_v3_hw 0000:32:04.0: PM: pci_pm_suspend(): suspend_v3_hw+0x0/0x210 [hisi_sas_v3_hw] returns -16
[15104.283527] hisi_sas_v3_hw 0000:32:04.0: PM: dpm_run_callback(): pci_pm_suspend+0x0/0x1c0 returns -16
[15104.283524] hisi_sas_v3_hw 0000:30:04.0: PM: pci_pm_suspend(): suspend_v3_hw+0x0/0x210 [hisi_sas_v3_hw] returns -16
[15104.283533] hisi_sas_v3_hw 0000:32:04.0: PM: failed to suspend async: error -16
[15104.283536] hisi_sas_v3_hw 0000:30:04.0: PM: dpm_run_callback(): pci_pm_suspend+0x0/0x1c0 returns -16
[15104.283542] hisi_sas_v3_hw 0000:30:04.0: PM: failed to suspend async: error -16
The problem is that when the ->runtime_suspend() callback
suspend_v3_hw() is executing, the current runtime PM status is
RPM_ACTIVE and the usage count of the controller is not 0, so return
immediately.
To fix it, Check the device usage count only when the runtime PM status
is RPM_SUSPENDING.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-7-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit 89954f024c ("scsi: hisi_sas: Ensure all enabled PHYs up
during controller reset"), we enable PHYs in parallel through async
operations and wait for PHYs come up. However, for some directly
attached SATA disks, the PHY not come up after a timeout period and the
hardware is not ready. At this time, we should get the latest PHY
hardware state, if the new PHY state is not ready but the old PHY state
is ready, call work HISI_PHYE_LINK_RESET to give it another chance to
phyup.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-6-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For the controller reset operation(such as FLR or clear nexus ha in SCSI
EH), we will disable all PHYs and then enable PHY based on the
hisi_hba->phy_state obtained in hisi_sas_controller_reset_prepare(). If
the device is removed before controller reset or the PHY is not attached
to any device in directly attached scenario, the corresponding bit of
phy_state is not set. After controller reset done, the PHY is disabled.
The device cannot be identified even if user reconnect the disk.
Therefore, for PHYs that are not disabled by user, hisi_sas_phy_enable()
needs to be executed even if the corresponding bit of phy_state is not
set.
Fixes: 89954f024c ("scsi: hisi_sas: Ensure all enabled PHYs up during controller reset")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-5-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For security purposes, after information is obtained through the FW,
check information to ensure data correctness.
- In v1 and v2 hw, the maximum number of PHYs is 9, while in v3 it is 8.
- In v2 and v3 hw, the maximum number of hardware queues is 16, while
in v1 it is 32.
Also add some debug logs for failure.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-4-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the current debugfs initialization process, the interface
trigger_dump is created first, and then the dump directory is created to
store the register dump information.
The issue is that after the trigger_dump interface is created, users can
access the interface to trigger dump and call
debugfs_create_files_v3_hw(). In debugfs_create_files_v3_hw(), if
.debugfs_dump_dentry is NULL, the file for storing dump information is
created under /sys/kernel/debug, and the memory and information cannot
be released after the driver is uninstalled.
Therefore, the creation of the trigger_dump interface is placed at the
end of debugfs initialization.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-3-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To be safe, we should register debugfs at the last stage of driver
initialization and then unregister debugfs at the first stage of driver
uninstallation.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-2-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A sanity check on phy_mask was added in commit 3668651def ("scsi:
mpi3mr: Sanitise num_phys"). This causes warning messages when more than
64 phys are detected and devices connected to phys greater than 64 are
dropped.
The phy_mask bitmap is only needed for controller phys and not required
for expander phys. Controller phys can go up to a maximum of 64 and
therefore u64 is good enough to contain phy_mask bitmap.
To suppress those warnings and allow devices to be discovered as before
the offending commit, restrict the phy_mask setting and lowest phy
setting only to the controller phys.
Fixes: 3668651def ("scsi: mpi3mr: Sanitise num_phys")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410051943.Mp9o5DlF-lkp@intel.com/
Reported-by: Alexander Motin <mav@ixsystems.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241008074353.200379-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
linux@treblig.org says:
Hi,
This removes a pile of dead functions in the SCSI bfa driver.
These were spotted by hunting for unused symbols in a unmodular
kernel build, and then double checking by grepping for the function
name.
It's been build tested only, I don't have the hardware, but
it's strictly full function (and the occasional struct) deletion,
so there should be no change in functionality.
Thanks to David Hildenbrand for the suggestion of hunting
for unused symbols.
Dave
Link: https://lore.kernel.org/r/20240915125633.25036-1-linux@treblig.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These functions aren't called anywhere, remove them.
Build tested only.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20240915125633.25036-5-linux@treblig.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These functions aren't called anywhere, remove them.
Build tested only.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20240915125633.25036-4-linux@treblig.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These functions aren't called anywhere, remove them.
Build tested only.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20240915125633.25036-3-linux@treblig.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
bfa_get_pciids and bfa_cfg_get_min aren't called anywhere; remove them
together with the bfa_pciid_s used by bfa_get_pciids.
(Build tested, I don't have the card)
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20240915125633.25036-2-linux@treblig.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
four small fixes, three in drivers and one in the FC transport class
to add idempotence to state setting.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZwnsDSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishZYjAP9QKRk5
1i/g9TyqFCurbt+R4BJGiNg+89WUnLxgNbThsgD9FqmXRsm2mGok02lQS4bz5Asv
OkNVO2se/q6IlplijV8=
=RCJc
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes, three in drivers and one in the FC transport class
to add idempotence to state setting"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: scsi_transport_fc: Allow setting rport state to current state
scsi: wd33c93: Don't use stale scsi_pointer value
scsi: fnic: Move flush_work initialization out of if block
scsi: ufs: Use pre-calculated offsets in ufshcd_init_lrb()
The only input fc_rport_set_marginal_state() currently accepts is
"Marginal" when port_state is "Online", and "Online" when the port_state
is "Marginal". It should also allow setting port_state to its current
state, either "Marginal or "Online".
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Link: https://lore.kernel.org/r/20240917230643.966768-1-bmarzins@redhat.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'aic7770_find_device()' has been unused since 2005's
commit dedd831081 ("[SCSI] aic7xxx: remove Linux 2.4 ifdefs")
Remove it and the associated constant. (Whether anyone still has one of
these cards in use is another question, I've just build tested this).
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20240913170116.250996-1-linux@treblig.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
aac_check_health() has been unused since commit
9473ddb2b0 ("scsi: aacraid: Use correct function to get ctrl health")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20240920202304.333108-1-linux@treblig.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A regression was introduced with commit dbb2da557a ("scsi: wd33c93:
Move the SCSI pointer to private command data") which results in an oops
in wd33c93_intr(). That commit added the scsi_pointer variable and
initialized it from hostdata->connected. However, during selection,
hostdata->connected is not yet valid. Fix this by getting the current
scsi_pointer from hostdata->selecting.
Cc: Daniel Palmer <daniel@0x0f.com>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@kernel.org
Fixes: dbb2da557a ("scsi: wd33c93: Move the SCSI pointer to private command data")
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Co-developed-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/09e11a0a54e6aa2a88bd214526d305aaf018f523.1727926187.git.fthain@linux-m68k.org
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After commit 379a58caa1 ("scsi: fnic: Move fnic_fnic_flush_tx() to a
work queue"), it can happen that a work item is sent to an uninitialized
work queue. This may has the effect that the item being queued is never
actually queued, and any further actions depending on it will not
proceed.
The following warning is observed while the fnic driver is loaded:
kernel: WARNING: CPU: 11 PID: 0 at ../kernel/workqueue.c:1524 __queue_work+0x373/0x410
kernel: <IRQ>
kernel: queue_work_on+0x3a/0x50
kernel: fnic_wq_copy_cmpl_handler+0x54a/0x730 [fnic 62fbff0c42e7fb825c60a55cde2fb91facb2ed24]
kernel: fnic_isr_msix_wq_copy+0x2d/0x60 [fnic 62fbff0c42e7fb825c60a55cde2fb91facb2ed24]
kernel: __handle_irq_event_percpu+0x36/0x1a0
kernel: handle_irq_event_percpu+0x30/0x70
kernel: handle_irq_event+0x34/0x60
kernel: handle_edge_irq+0x7e/0x1a0
kernel: __common_interrupt+0x3b/0xb0
kernel: common_interrupt+0x58/0xa0
kernel: </IRQ>
It has been observed that this may break the rediscovery of Fibre
Channel devices after a temporary fabric failure.
This patch fixes it by moving the work queue initialization out of
an if block in fnic_probe().
Signed-off-by: Martin Wilck <mwilck@suse.com>
Fixes: 379a58caa1 ("scsi: fnic: Move fnic_fnic_flush_tx() to a work queue")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240930133014.71615-1-mwilck@suse.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If container_of() is used correctly, its result is never NULL. Remove the
code that depends on container_of() returning a NULL pointer.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Link: https://lore.kernel.org/r/20240921062956.2027563-1-liaochen4@huawei.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
These are mostly minor updates. There are two drivers (lpfc and
mpi3mr) which missed the initial pull and a core change to retry a
start/stop unit which affect suspend/resume.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZvh4QiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQajAQDx561I
cgbPZjZkSOYp+qJowaphyySZ1SS8pfMlVAIiXQEAs4SqhIN8e9QWpgI0bA7X7xtB
UiOUsIHPHM+BFU6kbJQ=
=qjsp
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"These are mostly minor updates.
There are two drivers (lpfc and mpi3mr) which missed the initial
pull and a core change to retry a start/stop unit which affect
suspend/resume"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (32 commits)
scsi: lpfc: Update lpfc version to 14.4.0.5
scsi: lpfc: Support loopback tests with VMID enabled
scsi: lpfc: Revise TRACE_EVENT log flag severities from KERN_ERR to KERN_WARNING
scsi: lpfc: Ensure DA_ID handling completion before deleting an NPIV instance
scsi: lpfc: Fix kref imbalance on fabric ndlps from dev_loss_tmo handler
scsi: lpfc: Restrict support for 32 byte CDBs to specific HBAs
scsi: lpfc: Update phba link state conditional before sending CMF_SYNC_WQE
scsi: lpfc: Add ELS_RSP cmd to the list of WQEs to flush in lpfc_els_flush_cmd()
scsi: mpi3mr: Update driver version to 8.12.0.0.50
scsi: mpi3mr: Improve wait logic while controller transitions to READY state
scsi: mpi3mr: Update MPI Headers to revision 34
scsi: mpi3mr: Use firmware-provided timestamp update interval
scsi: mpi3mr: Enhance the Enable Controller retry logic
scsi: sd: Fix off-by-one error in sd_read_block_characteristics()
scsi: pm8001: Do not overwrite PCI queue mapping
scsi: scsi_debug: Remove a useless memset()
scsi: pmcraid: Convert comma to semicolon
scsi: sd: Retry START STOP UNIT commands
scsi: mpi3mr: A performance fix
scsi: ufs: qcom: Update MODE_MAX cfg_bw value
...
no_llseek had been defined to NULL two years ago, in commit 868941b144
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAmb0T5AQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpnfHEADCXqmqZC+xr3sHZH9T1lz9KaFp1FjuBhCw
bGpUgXQ9aLcqQUWJxmYVer8N2x2+Ds+xq4fm/rP1BfvNgRupqheHBwuLxSrz14EX
lYmKZ+krMIPTDaLFewmEWflDwmZX0WFgV6nKTMLiO5BMeI4zXCkFGtwYFys2+Cdd
9zYCFPgGDZUR77Ws5PpyqPVz2MoiNtsjrGmHpEmNZ+rIDzlpVOYgYk27X9ZbvNxC
/l0KTc9+ayAeG0Kx5jO+m6Hrj3I6ehvM9JZMgpS/tF/jtccD2oVkJFJDlU+Jciv6
BwVzgyDPGV7sXFT1fnSqDBYYwr/73nzNH0Gk8wn4Jg2LhjmVANVo9eQSOXDTYZI+
O4HfIHGTIrk75TQd4bhq3dqaylS78pKBI/eQJUli2UNoyLWMrMyE88yh2YJam2Fs
vJ/MHGxvFRurYbAlqLr33nb3ajvpg+D7XuAYfqHPMc2ZUe28Kza50Dj+luNjfVCu
3qfR6qBlsdWuABtUS3vneB9jZp5jDnOpVfuBgtcAqIboUjehTXsI7If09Ex/mxLq
O0KqNwBMfunPOKd5kGXlAgY8LRMfOhNaAAFBlXYUZB2eAadQnqVselTFvHMZkXo7
wH/l6trd+/Tf+7Rav0YduNIlpVr7IctC+A7ph4zPdIjQxFEySCrC7cvAjel29LyV
zgWW0Mw/sA==
=yiWu
-----END PGP SIGNATURE-----
Merge tag 'for-6.12/block-20240925' of git://git.kernel.dk/linux
Pull more block updates from Jens Axboe:
- Improve blk-integrity segment counting and merging (Keith)
- NVMe pull request via Keith:
- Multipath fixes (Hannes)
- Sysfs attribute list NULL terminate fix (Shin'ichiro)
- Remove problematic read-back (Keith)
- Fix for a regression with the IO scheduler switching freezing from
6.11 (Damien)
- Use a raw spinlock for sbitmap, as it may get called from preempt
disabled context (Ming)
- Cleanup for bd_claiming waiting, using var_waitqueue() rather than
the bit waitqueues, as that more accurately describes that it does
(Neil)
- Various cleanups (Kanchan, Qiu-ji, David)
* tag 'for-6.12/block-20240925' of git://git.kernel.dk/linux:
nvme: remove CC register read-back during enabling
nvme: null terminate nvme_tls_attrs
nvme-multipath: avoid hang on inaccessible namespaces
nvme-multipath: system fails to create generic nvme device
lib/sbitmap: define swap_lock as raw_spinlock_t
block: Remove unused blk_limits_io_{min,opt}
drbd: Fix atomicity violation in drbd_uuid_set_bm()
block: Fix elv_iosched_local_module handling of "none" scheduler
block: remove bogus union
block: change wait on bd_claiming to use a var_waitqueue
blk-integrity: improved sg segment mapping
block: unexport blk_rq_count_integrity_sg
nvme-rdma: use request to get integrity segments
scsi: use request to get integrity segments
block: provide a request helper for user integrity segments
blk-integrity: consider entire bio list for merging
blk-integrity: properly account for segments
blk-mq: set the nr_integrity_segments from bio
blk-mq: unconditional nr_integrity_segments
Quite a lot of nilfs2 work this time around.
Notable patch series in this pull request are:
"mul_u64_u64_div_u64: new implementation" by Nicolas Pitre, with
assistance from Uwe Kleine-König. Reimplement mul_u64_u64_div_u64() to
provide (much) more accurate results. The current implementation was
causing Uwe some issues in the PWM drivers.
"xz: Updates to license, filters, and compression options" from Lasse
Collin. Miscellaneous maintenance and kinor feature work to the xz
decompressor.
"Fix some GDB command error and add some GDB commands" from Kuan-Ying Lee.
Fixes and enhancements to the gdb scripts.
"treewide: add missing MODULE_DESCRIPTION() macros" from Jeff Johnson.
Adds lots of MODULE_DESCRIPTIONs, thus fixing lots of warnings about this.
"nilfs2: add support for some common ioctls" from Ryusuke Konishi. Adds
various commonly-available ioctls to nilfs2.
"This series fixes a number of formatting issues in kernel doc comments"
from Ryusuke Konishi does that.
"nilfs2: prevent unexpected ENOENT propagation" from Ryusuke Konishi. Fix
issues where -ENOENT was being unintentionally and inappropriately
returned to userspace.
"nilfs2: assorted cleanups" from Huang Xiaojia.
"nilfs2: fix potential issues with empty b-tree nodes" from Ryusuke
Konishi fixes some issues which can occur on corrupted nilfs2 filesystems.
"scripts/decode_stacktrace.sh: improve error reporting and usability" from
Luca Ceresoli does those things.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZu7dpAAKCRDdBJ7gKXxA
jsPqAPwMDEZyKlfSw7QioEHNHDkmkbP7VYCYR0CbUnppbztwpAD8D37aVbWQ+UzM
3nnOq3W2Pc2o/20zqi8Upf1mnvUrygQ=
=/NWE
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2024-09-21-07-52' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"Many singleton patches - please see the various changelogs for
details.
Quite a lot of nilfs2 work this time around.
Notable patch series in this pull request are:
- "mul_u64_u64_div_u64: new implementation" by Nicolas Pitre, with
assistance from Uwe Kleine-König. Reimplement mul_u64_u64_div_u64()
to provide (much) more accurate results. The current implementation
was causing Uwe some issues in the PWM drivers.
- "xz: Updates to license, filters, and compression options" from
Lasse Collin. Miscellaneous maintenance and kinor feature work to
the xz decompressor.
- "Fix some GDB command error and add some GDB commands" from
Kuan-Ying Lee. Fixes and enhancements to the gdb scripts.
- "treewide: add missing MODULE_DESCRIPTION() macros" from Jeff
Johnson. Adds lots of MODULE_DESCRIPTIONs, thus fixing lots of
warnings about this.
- "nilfs2: add support for some common ioctls" from Ryusuke Konishi.
Adds various commonly-available ioctls to nilfs2.
- "This series fixes a number of formatting issues in kernel doc
comments" from Ryusuke Konishi does that.
- "nilfs2: prevent unexpected ENOENT propagation" from Ryusuke
Konishi. Fix issues where -ENOENT was being unintentionally and
inappropriately returned to userspace.
- "nilfs2: assorted cleanups" from Huang Xiaojia.
- "nilfs2: fix potential issues with empty b-tree nodes" from Ryusuke
Konishi fixes some issues which can occur on corrupted nilfs2
filesystems.
- "scripts/decode_stacktrace.sh: improve error reporting and
usability" from Luca Ceresoli does those things"
* tag 'mm-nonmm-stable-2024-09-21-07-52' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (103 commits)
list: test: increase coverage of list_test_list_replace*()
list: test: fix tests for list_cut_position()
proc: use __auto_type more
treewide: correct the typo 'retun'
ocfs2: cleanup return value and mlog in ocfs2_global_read_info()
nilfs2: remove duplicate 'unlikely()' usage
nilfs2: fix potential oob read in nilfs_btree_check_delete()
nilfs2: determine empty node blocks as corrupted
nilfs2: fix potential null-ptr-deref in nilfs_btree_insert()
user_namespace: use kmemdup_array() instead of kmemdup() for multiple allocation
tools/mm: rm thp_swap_allocator_test when make clean
squashfs: fix percpu address space issues in decompressor_multi_percpu.c
lib: glob.c: added null check for character class
nilfs2: refactor nilfs_segctor_thread()
nilfs2: use kthread_create and kthread_stop for the log writer thread
nilfs2: remove sc_timer_task
nilfs2: do not repair reserved inode bitmap in nilfs_new_inode()
nilfs2: eliminate the shared counter and spinlock for i_generation
nilfs2: separate inode type information from i_state field
nilfs2: use the BITS_PER_LONG macro
...
Updates to the usual drivers (ufs, smartpqi, NCR5380, mac_scsi, lpfc,
mpi3mr). There are no user visible core changes and a whole series of
minor updates and fixes. The largest core change is probably the
simplification of the workqueue allocation path.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZuvd5yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishV7dAQC+TSlv
BeNm8W4yAFCXLCwnJh8rT6ZzuBsjsIHH1DPP3wD+IXuIOFf5gVRJGpCNJc/dI082
/ehSrIdeJxwaNoOOt+Y=
=SXZD
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, smartpqi, NCR5380, mac_scsi, lpfc,
mpi3mr).
There are no user visible core changes and a whole series of minor
updates and fixes. The largest core change is probably the
simplification of the workqueue allocation path"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (86 commits)
scsi: smartpqi: update driver version to 2.1.30-031
scsi: smartpqi: fix volume size updates
scsi: smartpqi: fix rare system hang during LUN reset
scsi: smartpqi: add new controller PCI IDs
scsi: smartpqi: add counter for parity write stream requests
scsi: smartpqi: correct stream detection
scsi: smartpqi: Add fw log to kdump
scsi: bnx2fc: Remove some unused fields in struct bnx2fc_rport
scsi: qla2xxx: Remove the unused 'del_list_entry' field in struct fc_port
scsi: ufs: core: Remove ufshcd_urgent_bkops()
scsi: core: Remove obsoleted declaration for scsi_driverbyte_string()
scsi: bnx2i: Remove unused declarations
scsi: core: Simplify an alloc_workqueue() invocation
scsi: ufs: Simplify alloc*_workqueue() invocation
scsi: stex: Simplify an alloc_ordered_workqueue() invocation
scsi: scsi_transport_fc: Simplify alloc_workqueue() invocations
scsi: snic: Simplify alloc_workqueue() invocations
scsi: qedi: Simplify an alloc_workqueue() invocation
scsi: qedf: Simplify alloc_workqueue() invocations
scsi: myrs: Simplify an alloc_ordered_workqueue() invocation
...
- support DMA zones for arm64 systems where memory starts at > 4GB
(Baruch Siach, Catalin Marinas)
- support direct calls into dma-iommu and thus obsolete dma_map_ops for
many common configurations (Leon Romanovsky)
- add DMA-API tracing (Sean Anderson)
- remove the not very useful return value from various dma_set_* APIs
(Christoph Hellwig)
- misc cleanups and minor optimizations (Chen Y, Yosry Ahmed,
Christoph Hellwig)
-----BEGIN PGP SIGNATURE-----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=DZVc
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-6.12-2024-09-19' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- support DMA zones for arm64 systems where memory starts at > 4GB
(Baruch Siach, Catalin Marinas)
- support direct calls into dma-iommu and thus obsolete dma_map_ops for
many common configurations (Leon Romanovsky)
- add DMA-API tracing (Sean Anderson)
- remove the not very useful return value from various dma_set_* APIs
(Christoph Hellwig)
- misc cleanups and minor optimizations (Chen Y, Yosry Ahmed, Christoph
Hellwig)
* tag 'dma-mapping-6.12-2024-09-19' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: reflow dma_supported
dma-mapping: reliably inform about DMA support for IOMMU
dma-mapping: add tracing for dma-mapping API calls
dma-mapping: use IOMMU DMA calls for common alloc/free page calls
dma-direct: optimize page freeing when it is not addressable
dma-mapping: clearly mark DMA ops as an architecture feature
vdpa_sim: don't select DMA_OPS
arm64: mm: keep low RAM dma zone
dma-mapping: don't return errors from dma_set_max_seg_size
dma-mapping: don't return errors from dma_set_seg_boundary
dma-mapping: don't return errors from dma_set_min_align_mask
scsi: check that busses support the DMA API before setting dma parameters
arm64: mm: fix DMA zone when dma-ranges is missing
dma-mapping: direct calls for dma-iommu
dma-mapping: call ->unmap_page and ->unmap_sg unconditionally
arm64: support DMA zone above 4GB
dma-mapping: replace zone_dma_bits by zone_dma_limit
dma-mapping: use bit masking to check VM_DMA_COHERENT
- Convert the qcom AHCI controller DT bindings to DT schema (from
Rayyan)
- Cleanup of libata core and drivers code handling controller and
device quirks to rename "blacklist" to the more neutral "quirk" and
to replace the rarely used "horkage" term with the more common
"quirk" naming (from me)
- Add libata-core message to print the quirks applied to a controller
or device (from me)
- Remove the not-so-useful function ata_noop_qc_prep() from libata core
(from me)
- ahci_imx driver cleanup, improvements and DT bindings compatible
strings update (from Richard and Dan)
- libahci_platform improvements (from Zhang)
- Remove obsolete functions declarations from libata header files (from
Gaosheng)
- Improve teh ahci_brcm driver using managed device resources funetions
(from Zhang)
- Introduce new helper function to improve libata EH code readability
(from Niklas)
- Enable module autoloading for the pata_ftide010, pata_ixp4xx and
sata_gemini drivers (from Liao)
- Move SATA related functions and data declaraions from libata-core to
libata-sata (from me)
- Rename the function handling the sense data for successful NCQ
commands log to better reflect that function actions (from me)
- Reduce libata memory usage by moving port resources to struct
ata_device and by optimizing the management of resources for CDL
capable devices (from me)
- Improve libata-eh handling of failed ATA passthrough commands (from
Niklas)
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCZuvJ2wAKCRDdoc3SxdoY
dhVhAP9Zctzd9Ylb17eO7vVDwA0p7nzqyDxwxWPL8p3FtSm8PQD+PWQaLAPfWmKD
X8RqWv9WDGvCGUTEBBSjiZslEp7ccwk=
=68kF
-----END PGP SIGNATURE-----
Merge tag 'ata-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata updates from Damien Le Moal:
- Convert the qcom AHCI controller DT bindings to DT schema (from
Rayyan)
- Cleanup of libata core and drivers code handling controller and
device quirks to rename "blacklist" to the more neutral "quirk" and
to replace the rarely used "horkage" term with the more common
"quirk" naming (me)
- Add libata-core message to print the quirks applied to a controller
or device (me)
- Remove the not-so-useful function ata_noop_qc_prep() from libata core
(me)
- ahci_imx driver cleanup, improvements and DT bindings compatible
strings update (Richard and Dan)
- libahci_platform improvements (Zhang)
- Remove obsolete functions declarations from libata header files (from
Gaosheng)
- Improve teh ahci_brcm driver using managed device resources funetions
(Zhang)
- Introduce new helper function to improve libata EH code readability
(Niklas)
- Enable module autoloading for the pata_ftide010, pata_ixp4xx and
sata_gemini drivers (Liao)
- Move SATA related functions and data declaraions from libata-core to
libata-sata (me)
- Rename the function handling the sense data for successful NCQ
commands log to better reflect that function actions (me)
- Reduce libata memory usage by moving port resources to struct
ata_device and by optimizing the management of resources for CDL
capable devices (me)
- Improve libata-eh handling of failed ATA passthrough commands
(Niklas)
* tag 'ata-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux: (39 commits)
ata: libata: Clear DID_TIME_OUT for ATA PT commands with sense data
ata: libata: Fix W=1 compilation warning
ata: libata: Improve CDL resource management
ata: libata: Introduce ata_dev_free_resources
ata: libata: Move sector_buf from struct ata_port to struct ata_device
ata: libata: Rename ata_eh_read_sense_success_ncq_log()
ata: libata: Move sata_std_hardreset() definition to libata-sata.c
ata: libata: Move sata_down_spd_limit() to libata-sata.c
ata: libata: Improve __ata_qc_complete()
ata: libata-scsi: Improve ata_scsi_handle_link_detach()
ata: libata: Cleanup libata-transport
ata: sata_gemini: Enable module autoloading
ata: pata_ixp4xx: Enable module autoloading
ata: pata_ftide010: Enable module autoloading
ata: libata: Add helper ata_eh_decide_disposition()
ata: ahci_brcm: Use devm_platform_ioremap_resource_byname() helper function
ata: libata: Remove obsolete function declarations
ata: ahci_imx: Fix error code in probe()
ata: libahci_platform: Simplify code with for_each_child_of_node_scoped()
ata: ahci_imx: Correct the email address
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmbm9fQeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGXcwH/A8+IXnrGv+VzYgD
+mE4hgGGHt4dClcUZ31gQetkkT6xktEVp6pB6JkFO7oEgBiTkJBbYGl6VZtsAIOd
Fi3jic8ik0uhZLFcxDJcHTceh6Pw8bkhWoh0tkF3bkDRwbppJdG7Khyk8DxTl24w
ldqh9om2cC7w9IPVx93xTgKgMMZ63qiJyUdTvxEZI3BG8F70smlgZSPskLp2Iktd
FIJZPcyKM0bhJYwZOpXK0vx5C2cA4oIW4xriHUw4aklv646OBxNKevB2JJAft2uA
6LyvuLgnYn/OpdFGZ8slvdmhm6hLWft5B1/bWKorUkz7p5YGiySFzpkMVAkNJ6mS
cRwHJNc=
=flw3
-----END PGP SIGNATURE-----
Merge tag 'v6.11' into for-6.12/block
Merge in 6.11 final to get the fix for preventing deadlocks on an
elevator switch, as there's a fixup for that patch.
* tag 'v6.11': (1788 commits)
Linux 6.11
Revert "KVM: VMX: Always honor guest PAT on CPUs that support self-snoop"
pinctrl: pinctrl-cy8c95x0: Fix regcache
cifs: Fix signature miscalculation
mm: avoid leaving partial pfn mappings around in error case
drm/xe/client: add missing bo locking in show_meminfo()
drm/xe/client: fix deadlock in show_meminfo()
drm/xe/oa: Enable Xe2+ PES disaggregation
drm/xe/display: fix compat IS_DISPLAY_STEP() range end
drm/xe: Fix access_ok check in user_fence_create
drm/xe: Fix possible UAF in guc_exec_queue_process_msg
drm/xe: Remove fence check from send_tlb_invalidation
drm/xe/gt: Remove double include
net: netfilter: move nf flowtable bpf initialization in nf_flow_table_module_init()
PCI: Fix potential deadlock in pcim_intx()
workqueue: Clear worker->pool in the worker thread context
net: tighten bad gso csum offset check in virtio_net_hdr
netlink: specs: mptcp: fix port endianness
net: dpaa: Pad packets to ETH_ZLEN
mptcp: pm: Fix uaf in __timer_delete_sync
...
Make the integrity mapping more like data mapping, blk_rq_map_sg. Use
the request to validate the segment count, and update the callers so
they don't have to.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20240913191746.2628196-1-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The request tracks the integrity segments already, so no need to recount
the segments again.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20240913182854.2445457-7-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Justin Tee <justintee8345@gmail.com> says:
Update lpfc to revision 14.4.0.5
This patch set contains bug fixes related to HBA state clean ups, FCP
discovery on older adapters, kref imbalances, log message improvements,
and support for a new diagnostic loopback testing mode.
The patches were cut against Martin's 6.12/scsi-queue tree.
Link: https://lore.kernel.org/r/20240912232447.45607-1-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The VMID feature adds an extra application services header to each frame.
As such, the loopback test path is updated to accommodate the extra
application header.
Changes include filling in APPID and WQES bit fields for XMIT_SEQUENCE64
commands, a special loopback source APPID for verifying received loopback
data matches what is sent, and increasing ELS WQ size to accommodate the
APPID field in loopback test mode.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240912232447.45607-8-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise certain log messages marked as KERN_ERR LOG_TRACE_EVENT to
KERN_WARNING and use the lpfc_vlog_msg() macro to still log the event. The
benefit is that events of interest are still logged and the entire trace
buffer is not dumped with extraneous logging information when using default
lpfc_log_verbose driver parameter settings.
Also, delete the keyword "fail" from such log messages as they aren't
really causes for concern. The log messages are more for warnings to a SAN
admin about SAN activity.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240912232447.45607-7-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Deleting an NPIV instance requires all fabric ndlps to be released before
an NPIV's resources can be torn down. Failure to release fabric ndlps
beforehand opens kref imbalance race conditions. Fix by forcing the DA_ID
to complete synchronously with usage of wait_queue.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240912232447.45607-6-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With a FLOGI outstanding and loss of physical link connection to the fabric
for the duration of dev_loss_tmo, there is a fabric ndlp kref imbalance
that decrements the kref and sets the NLP_IN_RECOV_POST_DEV_LOSS flag at
the same time.
The issue is that when the FLOGI completion routine executes, the fabric
ndlp could already be freed because of the final kref put from the
dev_loss_tmo handler. Fix by early returning before the ndlp kref put if
the ndlp is deemed a candidate for NLP_IN_RECOV_POST_DEV_LOSS in the FLOGI
completion routine.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240912232447.45607-5-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An older generation of HBAs are failing FCP discovery due to usage of an
outdated field in FCP command WQEs.
Fix by checking the SLI Interface Type register for applicable support of
32 Byte CDB commands, and restore a setting for a WQE path using normal 16
byte CDBs.
Fixes: af20bb73ac ("scsi: lpfc: Add support for 32 byte CDBs")
Cc: stable@vger.kernel.org # v6.10+
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240912232447.45607-4-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's possible for the driver to send a CMF_SYNC_WQE to nonresponsive
firmware during reset of the adapter. The phba link_state conditional
check is currently a strict == LPFC_LINK_DOWN, which does not cover
initialization states before reaching the LPFC_LINK_UP state.
Update the phba->link_state conditional to < LPFC_LINK_UP so that all
initialization states are covered before allowing sending CMF_SYNC_WQE.
Update taking of the hbalock to be during this link_state check as well.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240912232447.45607-3-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During HBA stress testing, a spam of received PLOGIs exposes a resource
recovery bug causing leakage of lpfc_sqlq entries from the global
phba->sli4_hba.lpfc_els_sgl_list.
The issue is in lpfc_els_flush_cmd(), where the driver attempts to recover
outstanding ELS sgls when walking the txcmplq. Only CMD_ELS_REQUEST64_CRs
and CMD_GEN_REQUEST64_CRs are added to the abort and cancel lists. A check
for CMD_XMIT_ELS_RSP64_WQE is missing in order to recover LS_ACC usages of
the phba->sli4_hba.lpfc_els_sgl_list too.
Fix by adding CMD_XMIT_ELS_RSP64_WQE as part of the txcmplq walk when
adding WQEs to the abort and cancel list in lpfc_els_flush_cmd(). Also,
update naming convention from CRs to WQEs.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240912232447.45607-2-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During controller transitioning to READY state, if the controller is found
in transient states ("becoming ready" or "reset requested"), driver waits
for 510 secs even if the controller transitions out of these states
early. This causes an unnecessary delay of 510 secs in the overall firmware
initialization sequence.
Poll the controller state periodically (every 100 milliseconds) while
waiting for the controller to come out of the mentioned transient
states. Once the controller transits out of the transient states, come out
of the wait loop.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20240905102753.105310-5-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make driver use the timestamp update interval value provided by firmware in
the driver page 1. If firmware fails to provide non-zero value, then the
driver will fall back to the driver defined macro.
Signed-off-by: Prayas Patel <prayas.patel@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20240905102753.105310-3-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When enabling the IOC request and polling for controller ready status, poll
for controller fault and reset history bit. If the controller is faulted
or the reset history bit is set, retry the initialization a maximum of
three times (2 retries) or if the cumulative time taken for all retries
exceeds 510 seconds.
Signed-off-by: Prayas Patel <prayas.patel@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20240905102753.105310-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ff the device returns page 0xb1 with length 8 (happens with qemu v2.x, for
example), sd_read_block_characteristics() may attempt an out-of-bounds
memory access when accessing the zoned field at offset 8.
Fixes: 7fb019c46e ("scsi: sd: Switch to using scsi_device VPD pages")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Wilck <mwilck@suse.com>
Link: https://lore.kernel.org/r/20240912134308.282824-1-mwilck@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
blk_mq_pci_map_queues() maps all queues but right after this, we overwrite
these mappings by calling blk_mq_map_queues(). Just use one helper but not
both.
Fixes: 42f22fe36d ("scsi: pm8001: Expose hardware queues for pm80xx")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Link: https://lore.kernel.org/r/20240912-do-not-overwrite-pci-mapping-v1-1-85724b6cec49@suse.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace comma between expressions with semicolons.
Using a ',' in place of a ';' can have unintended side effects. Although
that is not the case here, it is seems best to use ';' unless ',' is
intended.
Found by inspection. No functional change intended. Compile tested only.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/r/20240905023521.1642862-1-nichen@iscas.ac.cn
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During system resume, sd_start_stop_device() submits a START STOP UNIT
command to the SCSI device that is being resumed. That command is not
retried in case of a unit attention and hence may fail. An example:
[16575.983359] sd 0:0:0:3: [sdd] Starting disk
[16575.983693] sd 0:0:0:3: [sdd] Start/Stop Unit failed: Result: hostbyte=0x00 driverbyte=DRIVER_OK
[16575.983712] sd 0:0:0:3: [sdd] Sense Key : 0x6
[16575.983730] sd 0:0:0:3: [sdd] ASC=0x29 ASCQ=0x0
[16575.983738] sd 0:0:0:3: PM: dpm_run_callback(): scsi_bus_resume+0x0/0xa0 returns -5
[16575.983783] sd 0:0:0:3: PM: failed to resume async: error -5
Make the SCSI core retry the START STOP UNIT command if the device reports
that it has been powered on or that it has been reset.
Cc: Damien Le Moal <dlemoal@kernel.org>
Cc: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240904210304.2947789-1-bvanassche@acm.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 0c52310f26 ("hrtimer: Ignore slack time for RT tasks in
schedule_hrtimeout_range()") effectivelly shortens a sleep in a polling
function in the driver. That is causing a performance regression as the
new value of just 2us is too low, in certain tests the perf drop is ~30%.
Fix this by adjusting the sleep to 20us (close to the previous value).
Reported-by: Jan Jurca <jjurca@redhat.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20240903144729.37218-1-thenzl@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
