Before calling lan743x_ptp_io_event_clock_get(), the 'channel' value
is checked against the maximum value of PCI11X1X_PTP_IO_MAX_CHANNELS(8).
This seems correct and aligns with the PTP interrupt status register
(PTP_INT_STS) specifications.
However, lan743x_ptp_io_event_clock_get() writes to ptp->extts[] with
only LAN743X_PTP_N_EXTTS(4) elements, using channel as an index:
lan743x_ptp_io_event_clock_get(..., u8 channel,...)
{
...
/* Update Local timestamp */
extts = &ptp->extts[channel];
extts->ts.tv_sec = sec;
...
}
To avoid an out-of-bounds write and utilize all the supported GPIO
inputs, set LAN743X_PTP_N_EXTTS to 8.
Detected using the static analysis tool - Svace.
Fixes: 60942c397a ("net: lan743x: Add support for PTP-IO Event Input External Timestamp (extts)")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://patch.msgid.link/20250616113743.36284-1-aleksei.kodanev@bell-sw.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Migrate to new callbacks added by commit 9bb00786fc ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
This driver's RXFH config is read only / fixed so the conversion
is purely factoring out the handling into a helper.
Reviewed-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20250614180638.4166766-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When running these commands on DUT (and similar at the other end)
ip link set dev eth0 up
ip link add link eth0 name eth0.10 type vlan id 10
ip addr add 10.0.0.1/24 dev eth0.10
ip link set dev eth0.10 up
ping 10.0.0.2
The ping will fail.
The reason why is failing is because, the network interfaces for lan966x
have a flag saying that the HW can insert the vlan tags into the
frames(NETIF_F_HW_VLAN_CTAG_TX). Meaning that the frames that are
transmitted don't have the vlan tag inside the skb data, but they have
it inside the skb. We already get that vlan tag and put it in the IFH
but the problem is that we don't configure the HW to rewrite the frame
when the interface is in host mode.
The fix consists in actually configuring the HW to insert the vlan tag
if it is different than 0.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Fixes: 6d2c186afa ("net: lan966x: Add vlan support.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250528093619.3738998-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Maximum OTP and EEPROM size for hearthstone PCI1xxxx devices are 8 Kb
and 64 Kb respectively. Adjust max size definitions and return correct
EEPROM length based on device. Also prevent out-of-bound read/write.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://patch.msgid.link/20250523173326.18509-1-rengarajan.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove lan743x_phy_init from lan743x_hardware_init as it resets the PHY
registers, causing WOL to fail on subsequent attempts. Add a call to
lan743x_hw_reset_phy in the probe function to ensure the PHY is reset
during device initialization.
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250526053048.287095-3-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rename the function to lan743x_hw_reset_phy to better describe it
operation.
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250526053048.287095-2-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When enabling 1-step timestamping for ptp frames that are over udpv4 or
udpv6 then the inserted timestamp is added at the wrong offset in the
frame, meaning that will modify the frame at the wrong place, so the
frame will be malformed.
To fix this, the HW needs to know which kind of frame it is to know
where to insert the timestamp. For that there is a field in the IFH that
says the PDU_TYPE, which can be NONE which is the default value,
IPV4 or IPV6. Therefore make sure to set the PDU_TYPE so the HW knows
where to insert the timestamp.
Like I mention before the issue is not seen with L2 frames because by
default the PDU_TYPE has a value of 0, which represents the L2 frames.
Fixes: 77eecf25bd ("net: lan966x: Update extraction/injection for timestamping")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250521124159.2713525-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cross-merge networking fixes after downstream PR (net-6.15-rc8).
Conflicts:
80f2ab46c2 ("irdma: free iwdev->rf after removing MSI-X")
4bcc063939 ("ice, irdma: fix an off by one in error handling code")
c24a65b6a2 ("iidc/ice/irdma: Update IDC to support multiple consumers")
https://lore.kernel.org/20250513130630.280ee6c5@canb.auug.org.au
No extra adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SGMII_CTRL register, which specifies the active interface, was not
properly restored when resuming from suspend. This led to incorrect
interface selection after resume particularly in scenarios involving
the FPGA.
To fix this:
- Move the SGMII_CTRL setup out of the probe function.
- Initialize the register in the hardware initialization helper function,
which is called during both device initialization and resume.
This ensures the interface configuration is consistently restored after
suspend/resume cycles.
Fixes: a46d9d37c4 ("net: lan743x: Add support for SGMII interface")
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Link: https://patch.msgid.link/20250516035719.117960-1-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Permit programs such as "hwtstamp_ctl -i eth0" to retrieve the current
timestamping configuration of the NIC, rather than returning "Device
driver does not have support for non-destructive SIOCGHWTSTAMP."
The driver configures all channels with the same timestamping settings.
On TX, retrieve the settings of the first channel, those should be
representative for the entire NIC. On RX, save the filter settings in a
new adapter field.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250514151931.1988047-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
New timestamping API was introduced in commit 66f7223039 ("net: add
NDOs for configuring hardware timestamping") from kernel v6.6.
It is time to convert the lan743x driver to the new API, so that
timestamping configuration can be removed from the ndo_eth_ioctl()
path completely.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250514151931.1988047-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Always map the `skb` to the LS descriptor. Previously skb was
mapped to EXT descriptor when the number of fragments is zero with
GSO enabled. Mapping the skb to EXT descriptor prevents it from
being freed, leading to a memory leak
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250429052527.10031-1-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver allocates ring elements using GFP_DMA flags. There is
no dependency from LAN743x hardware on memory allocation should be
in DMA_ZONE. Hence modifying the flags to use only GFP_ATOMIC. This
is consistent with other callers of lan743x_rx_init_ring_element().
Reported-by: Zhang, Liyin(CN) <Liyin.Zhang.CN@windriver.com>
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250415044509.6695-1-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PTP_PEROUT_REQUEST2 ioctl has gained support for flags specifying
specific output behavior including PTP_PEROUT_ONE_SHOT,
PTP_PEROUT_DUTY_CYCLE, PTP_PEROUT_PHASE.
Driver authors are notorious for not checking the flags of the request.
This results in misinterpreting the request, generating an output signal
that does not match the requested value. It is anticipated that even more
flags will be added in the future, resulting in even more broken requests.
Expecting these issues to be caught during review or playing whack-a-mole
after the fact is not a great solution.
Instead, introduce the supported_perout_flags field in the ptp_clock_info
structure. Update the core character device logic to explicitly reject any
request which has a flag not on this list.
This ensures that drivers must 'opt in' to the flags they support. Drivers
which don't set the .supported_perout_flags field will not need to check
that unsupported flags aren't passed, as the core takes care of this.
Update the drivers which do support flags to set this new field.
Note the following driver files set n_per_out to a non-zero value but did
not check the flags at all:
• drivers/ptp/ptp_clockmatrix.c
• drivers/ptp/ptp_idt82p33.c
• drivers/ptp/ptp_fc3.c
• drivers/net/ethernet/ti/am65-cpts.c
• drivers/net/ethernet/aquantia/atlantic/aq_ptp.c
• drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c
• drivers/net/dsa/sja1105/sja1105_ptp.c
• drivers/net/ethernet/freescale/dpaa2/dpaa2-ptp.c
• drivers/net/ethernet/mscc/ocelot_vsc7514.c
• drivers/net/ethernet/intel/i40e/i40e_ptp.c
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250414-jk-supported-perout-flags-v2-2-f6b17d15475c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PTP_EXTTS_REQUEST(2) ioctl has a flags field which specifies how the
external timestamp request should behave. This includes which edge of the
signal to timestamp, as well as a specialized "offset" mode. It is expected
that more flags will be added in the future.
Driver authors routinely do not check the flags, often accepting requests
with flags which they do not support. Even drivers which do check flags may
not be future-proofed to reject flags not yet defined. Thus, any future
flag additions often require manually updating drivers to reject these
flags.
This approach of hoping we catch flag checks during review, or playing
whack-a-mole after the fact is the wrong approach.
Introduce the "supported_extts_flags" field to the ptp_clock_info
structure. This field defines the set of flags the device actually
supports.
Update the core character device logic to check this field and reject
unsupported requests. Getting this right is somewhat tricky. First, to
avoid unnecessary repetition and make basic functionality work when
.supported_extts_flags is 0, the core always accepts the PTP_ENABLE_FEATURE
flag. This flag is used to set the 'on' parameter to the .enable function
and is thus always 'supported' by all drivers.
For backwards compatibility, the PTP_RISING_EDGE and PTP_FALLING_EDGE flags
are merely "hints" when using the old PTP_EXTTS_REQUEST ioctl, and are not
expected to be enforced. If the user issues PTP_EXTTS_REQUEST2, the
PTP_STRICT_FLAGS flag is added which is supposed to inform the driver to
strictly validate the flags and reject unsupported requests. To handle
this, first check if the driver reports PTP_STRICT_FLAGS support. If it
does not, then always allow the PTP_RISING_EDGE and PTP_FALLING_EDGE flags.
This keeps backwards compatibility with the original PTP_EXTTS_REQUEST
ioctl where these flags are not guaranteed to be honored.
This way, drivers which do not set the supported_extts_flags will continue
to accept requests for the original PTP_EXTTS_REQUEST ioctl. The core will
automatically reject requests with new flags, and correctly reject requests
with PTP_STRICT_FLAGS, where the driver is supposed to strictly validate
the flags.
Update the various drivers, refactoring their validation logic into the
.supported_extts_flags field. For consistency and readability,
PTP_ENABLE_FEATURE is not set in the supported flags list, and
PTP_EXTTS_EDGES is expanded to PTP_RISING_EDGE | PTP_FALLING_EDGE in all
cases.
Note the following driver files set n_ext_ts to a non-zero value but did
not check flags at all:
• drivers/net/ethernet/freescale/dpaa2/dpaa2-ptp.c
• drivers/net/ethernet/freescale/enetc/enetc_ptp.c
• drivers/net/ethernet/intel/i40e/i40e_ptp.c
• drivers/net/ethernet/marvell/octeontx2/nic/otx2_ptp.c
• drivers/net/ethernet/renesas/ravb_ptp.c
• drivers/net/ethernet/renesas/rtsn.c
• drivers/net/ethernet/renesas/rtsn.h
• drivers/net/ethernet/ti/am65-cpts.c
• drivers/net/ethernet/ti/cpts.h
• drivers/net/ethernet/ti/icssg/icss_iep.c
• drivers/net/ethernet/xscale/ptp_ixp46x.c
• drivers/net/phy/bcm-phy-ptp.c
• drivers/ptp/ptp_ocp.c
• drivers/ptp/ptp_pch.c
• drivers/ptp/ptp_qoriq.c
These drivers behavior does change slightly: they will now reject the
PTP_EXTTS_REQUEST2 ioctl, because they do not strictly validate their
flags. This also makes them no longer incorrectly accept PTP_EXT_OFFSET.
Also note that the renesas ravb driver does not support PTP_STRICT_FLAGS.
We could leave the .supported_extts_flags as 0, but I added the
PTP_RISING_EDGE | PTP_FALLING_EDGE since the driver previously manually
validated these flags. This is equivalent to 0 because the core will allow
these flags regardless unless PTP_STRICT_FLAGS is also set.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250414-jk-supported-perout-flags-v2-1-f6b17d15475c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Core & protocols
----------------
- Continue Netlink conversions to per-namespace RTNL lock
(IPv4 routing, routing rules, routing next hops, ARP ioctls).
- Continue extending the use of netdev instance locks. As a driver
opt-in protect queue operations and (in due course) ethtool
operations with the instance lock and not RTNL lock.
- Support collecting TCP timestamps (data submitted, sent, acked)
in BPF, allowing for transparent (to the application) and lower
overhead tracking of TCP RPC performance.
- Tweak existing networking Rx zero-copy infra to support zero-copy
Rx via io_uring.
- Optimize MPTCP performance in single subflow mode by 29%.
- Enable GRO on packets which went thru XDP CPU redirect (were queued
for processing on a different CPU). Improving TCP stream performance
up to 2x.
- Improve performance of contended connect() by 200% by searching
for an available 4-tuple under RCU rather than a spin lock.
Bring an additional 229% improvement by tweaking hash distribution.
- Avoid unconditionally touching sk_tsflags on RX, improving
performance under UDP flood by as much as 10%.
- Avoid skb_clone() dance in ping_rcv() to improve performance under
ping flood.
- Avoid FIB lookup in netfilter if socket is available, 20% perf win.
- Rework network device creation (in-kernel) API to more clearly
identify network namespaces and their roles.
There are up to 4 namespace roles but we used to have just 2 netns
pointer arguments, interpreted differently based on context.
- Use sysfs_break_active_protection() instead of trylock to avoid
deadlocks between unregistering objects and sysfs access.
- Add a new sysctl and sockopt for capping max retransmit timeout
in TCP.
- Support masking port and DSCP in routing rule matches.
- Support dumping IPv4 multicast addresses with RTM_GETMULTICAST.
- Support specifying at what time packet should be sent on AF_XDP
sockets.
- Expose TCP ULP diagnostic info (for TLS and MPTCP) to non-admin users.
- Add Netlink YAML spec for WiFi (nl80211) and conntrack.
- Introduce EXPORT_IPV6_MOD() and EXPORT_IPV6_MOD_GPL() for symbols
which only need to be exported when IPv6 support is built as a module.
- Age FDB entries based on Rx not Tx traffic in VxLAN, similar
to normal bridging.
- Allow users to specify source port range for GENEVE tunnels.
- netconsole: allow attaching kernel release, CPU ID and task name
to messages as metadata
Driver API
----------
- Continue rework / fixing of Energy Efficient Ethernet (EEE) across
the SW layers. Delegate the responsibilities to phylink where possible.
Improve its handling in phylib.
- Support symmetric OR-XOR RSS hashing algorithm.
- Support tracking and preserving IRQ affinity by NAPI itself.
- Support loopback mode speed selection for interface selftests.
Device drivers
--------------
- Remove the IBM LCS driver for s390.
- Remove the sb1000 cable modem driver.
- Add support for SFP module access over SMBus.
- Add MCTP transport driver for MCTP-over-USB.
- Enable XDP metadata support in multiple drivers.
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- add PCIe TLP Processing Hints (TPH) support for new AMD platforms
- support dumping RoCE queue state for debug
- opt into instance locking
- Intel (100G, ice, idpf):
- ice: rework MSI-X IRQ management and distribution
- ice: support for E830 devices
- iavf: add support for Rx timestamping
- iavf: opt into instance locking
- nVidia/Mellanox:
- mlx4: use page pool memory allocator for Rx
- mlx5: support for one PTP device per hardware clock
- mlx5: support for 200Gbps per-lane link modes
- mlx5: move IPSec policy check after decryption
- AMD/Solarflare:
- support FW flashing via devlink
- Cisco (enic):
- use page pool memory allocator for Rx
- enable 32, 64 byte CQEs
- get max rx/tx ring size from the device
- Meta (fbnic):
- support flow steering and RSS configuration
- report queue stats
- support TCP segmentation
- support IRQ coalescing
- support ring size configuration
- Marvell/Cavium:
- support AF_XDP
- Wangxun:
- support for PTP clock and timestamping
- Huawei (hibmcge):
- checksum offload
- add more statistics
- Ethernet virtual:
- VirtIO net:
- aggressively suppress Tx completions, improve perf by 96% with
1 CPU and 55% with 2 CPUs
- expose NAPI to IRQ mapping and persist NAPI settings
- Google (gve):
- support XDP in DQO RDA Queue Format
- opt into instance locking
- Microsoft vNIC:
- support BIG TCP
- Ethernet NICs consumer, and embedded:
- Synopsys (stmmac):
- cleanup Tx and Tx clock setting and other link-focused cleanups
- enable SGMII and 2500BASEX mode switching for Intel platforms
- support Sophgo SG2044
- Broadcom switches (b53):
- support for BCM53101
- TI:
- iep: add perout configuration support
- icssg: support XDP
- Cadence (macb):
- implement BQL
- Xilinx (axinet):
- support dynamic IRQ moderation and changing coalescing at runtime
- implement BQL
- report standard stats
- MediaTek:
- support phylink managed EEE
- Intel:
- igc: don't restart the interface on every XDP program change
- RealTek (r8169):
- support reading registers of internal PHYs directly
- increase max jumbo packet size on RTL8125/RTL8126
- Airoha:
- support for RISC-V NPU packet processing unit
- enable scatter-gather and support MTU up to 9kB
- Tehuti (tn40xx):
- support cards with TN4010 MAC and an Aquantia AQR105 PHY
- Ethernet PHYs:
- support for TJA1102S, TJA1121
- dp83tg720: add randomized polling intervals for link detection
- dp83822: support changing the transmit amplitude voltage
- support for LEDs on 88q2xxx
- CAN:
- canxl: support Remote Request Substitution bit access
- flexcan: add S32G2/S32G3 SoC
- WiFi:
- remove cooked monitor support
- strict mode for better AP testing
- basic EPCS support
- OMI RX bandwidth reduction support
- batman-adv: add support for jumbo frames
- WiFi drivers:
- RealTek (rtw88):
- support RTL8814AE and RTL8814AU
- RealTek (rtw89):
- switch using wiphy_lock and wiphy_work
- add BB context to manipulate two PHY as preparation of MLO
- improve BT-coexistence mechanism to play A2DP smoothly
- Intel (iwlwifi):
- add new iwlmld sub-driver for latest HW/FW combinations
- MediaTek (mt76):
- preparation for mt7996 Multi-Link Operation (MLO) support
- Qualcomm/Atheros (ath12k):
- continued work on MLO
- Silabs (wfx):
- Wake-on-WLAN support
- Bluetooth:
- add support for skb TX SND/COMPLETION timestamping
- hci_core: enable buffer flow control for SCO/eSCO
- coredump: log devcd dumps into the monitor
- Bluetooth drivers:
- intel: add support to configure TX power
- nxp: handle bootloader error during cmd5 and cmd7
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=XY0S
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Continue Netlink conversions to per-namespace RTNL lock
(IPv4 routing, routing rules, routing next hops, ARP ioctls)
- Continue extending the use of netdev instance locks. As a driver
opt-in protect queue operations and (in due course) ethtool
operations with the instance lock and not RTNL lock.
- Support collecting TCP timestamps (data submitted, sent, acked) in
BPF, allowing for transparent (to the application) and lower
overhead tracking of TCP RPC performance.
- Tweak existing networking Rx zero-copy infra to support zero-copy
Rx via io_uring.
- Optimize MPTCP performance in single subflow mode by 29%.
- Enable GRO on packets which went thru XDP CPU redirect (were queued
for processing on a different CPU). Improving TCP stream
performance up to 2x.
- Improve performance of contended connect() by 200% by searching for
an available 4-tuple under RCU rather than a spin lock. Bring an
additional 229% improvement by tweaking hash distribution.
- Avoid unconditionally touching sk_tsflags on RX, improving
performance under UDP flood by as much as 10%.
- Avoid skb_clone() dance in ping_rcv() to improve performance under
ping flood.
- Avoid FIB lookup in netfilter if socket is available, 20% perf win.
- Rework network device creation (in-kernel) API to more clearly
identify network namespaces and their roles. There are up to 4
namespace roles but we used to have just 2 netns pointer arguments,
interpreted differently based on context.
- Use sysfs_break_active_protection() instead of trylock to avoid
deadlocks between unregistering objects and sysfs access.
- Add a new sysctl and sockopt for capping max retransmit timeout in
TCP.
- Support masking port and DSCP in routing rule matches.
- Support dumping IPv4 multicast addresses with RTM_GETMULTICAST.
- Support specifying at what time packet should be sent on AF_XDP
sockets.
- Expose TCP ULP diagnostic info (for TLS and MPTCP) to non-admin
users.
- Add Netlink YAML spec for WiFi (nl80211) and conntrack.
- Introduce EXPORT_IPV6_MOD() and EXPORT_IPV6_MOD_GPL() for symbols
which only need to be exported when IPv6 support is built as a
module.
- Age FDB entries based on Rx not Tx traffic in VxLAN, similar to
normal bridging.
- Allow users to specify source port range for GENEVE tunnels.
- netconsole: allow attaching kernel release, CPU ID and task name to
messages as metadata
Driver API:
- Continue rework / fixing of Energy Efficient Ethernet (EEE) across
the SW layers. Delegate the responsibilities to phylink where
possible. Improve its handling in phylib.
- Support symmetric OR-XOR RSS hashing algorithm.
- Support tracking and preserving IRQ affinity by NAPI itself.
- Support loopback mode speed selection for interface selftests.
Device drivers:
- Remove the IBM LCS driver for s390
- Remove the sb1000 cable modem driver
- Add support for SFP module access over SMBus
- Add MCTP transport driver for MCTP-over-USB
- Enable XDP metadata support in multiple drivers
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- add PCIe TLP Processing Hints (TPH) support for new AMD
platforms
- support dumping RoCE queue state for debug
- opt into instance locking
- Intel (100G, ice, idpf):
- ice: rework MSI-X IRQ management and distribution
- ice: support for E830 devices
- iavf: add support for Rx timestamping
- iavf: opt into instance locking
- nVidia/Mellanox:
- mlx4: use page pool memory allocator for Rx
- mlx5: support for one PTP device per hardware clock
- mlx5: support for 200Gbps per-lane link modes
- mlx5: move IPSec policy check after decryption
- AMD/Solarflare:
- support FW flashing via devlink
- Cisco (enic):
- use page pool memory allocator for Rx
- enable 32, 64 byte CQEs
- get max rx/tx ring size from the device
- Meta (fbnic):
- support flow steering and RSS configuration
- report queue stats
- support TCP segmentation
- support IRQ coalescing
- support ring size configuration
- Marvell/Cavium:
- support AF_XDP
- Wangxun:
- support for PTP clock and timestamping
- Huawei (hibmcge):
- checksum offload
- add more statistics
- Ethernet virtual:
- VirtIO net:
- aggressively suppress Tx completions, improve perf by 96%
with 1 CPU and 55% with 2 CPUs
- expose NAPI to IRQ mapping and persist NAPI settings
- Google (gve):
- support XDP in DQO RDA Queue Format
- opt into instance locking
- Microsoft vNIC:
- support BIG TCP
- Ethernet NICs consumer, and embedded:
- Synopsys (stmmac):
- cleanup Tx and Tx clock setting and other link-focused
cleanups
- enable SGMII and 2500BASEX mode switching for Intel platforms
- support Sophgo SG2044
- Broadcom switches (b53):
- support for BCM53101
- TI:
- iep: add perout configuration support
- icssg: support XDP
- Cadence (macb):
- implement BQL
- Xilinx (axinet):
- support dynamic IRQ moderation and changing coalescing at
runtime
- implement BQL
- report standard stats
- MediaTek:
- support phylink managed EEE
- Intel:
- igc: don't restart the interface on every XDP program change
- RealTek (r8169):
- support reading registers of internal PHYs directly
- increase max jumbo packet size on RTL8125/RTL8126
- Airoha:
- support for RISC-V NPU packet processing unit
- enable scatter-gather and support MTU up to 9kB
- Tehuti (tn40xx):
- support cards with TN4010 MAC and an Aquantia AQR105 PHY
- Ethernet PHYs:
- support for TJA1102S, TJA1121
- dp83tg720: add randomized polling intervals for link detection
- dp83822: support changing the transmit amplitude voltage
- support for LEDs on 88q2xxx
- CAN:
- canxl: support Remote Request Substitution bit access
- flexcan: add S32G2/S32G3 SoC
- WiFi:
- remove cooked monitor support
- strict mode for better AP testing
- basic EPCS support
- OMI RX bandwidth reduction support
- batman-adv: add support for jumbo frames
- WiFi drivers:
- RealTek (rtw88):
- support RTL8814AE and RTL8814AU
- RealTek (rtw89):
- switch using wiphy_lock and wiphy_work
- add BB context to manipulate two PHY as preparation of MLO
- improve BT-coexistence mechanism to play A2DP smoothly
- Intel (iwlwifi):
- add new iwlmld sub-driver for latest HW/FW combinations
- MediaTek (mt76):
- preparation for mt7996 Multi-Link Operation (MLO) support
- Qualcomm/Atheros (ath12k):
- continued work on MLO
- Silabs (wfx):
- Wake-on-WLAN support
- Bluetooth:
- add support for skb TX SND/COMPLETION timestamping
- hci_core: enable buffer flow control for SCO/eSCO
- coredump: log devcd dumps into the monitor
- Bluetooth drivers:
- intel: add support to configure TX power
- nxp: handle bootloader error during cmd5 and cmd7"
* tag 'net-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1681 commits)
unix: fix up for "apparmor: add fine grained af_unix mediation"
mctp: Fix incorrect tx flow invalidation condition in mctp-i2c
net: usb: asix: ax88772: Increase phy_name size
net: phy: Introduce PHY_ID_SIZE — minimum size for PHY ID string
net: libwx: fix Tx L4 checksum
net: libwx: fix Tx descriptor content for some tunnel packets
atm: Fix NULL pointer dereference
net: tn40xx: add pci-id of the aqr105-based Tehuti TN4010 cards
net: tn40xx: prepare tn40xx driver to find phy of the TN9510 card
net: tn40xx: create swnode for mdio and aqr105 phy and add to mdiobus
net: phy: aquantia: add essential functions to aqr105 driver
net: phy: aquantia: search for firmware-name in fwnode
net: phy: aquantia: add probe function to aqr105 for firmware loading
net: phy: Add swnode support to mdiobus_scan
gve: add XDP DROP and PASS support for DQ
gve: update XDP allocation path support RX buffer posting
gve: merge packet buffer size fields
gve: update GQ RX to use buf_size
gve: introduce config-based allocation for XDP
gve: remove xdp_xsk_done and xdp_xsk_wakeup statistics
...
The lan743x_ptp_io_event_cap_en() function checks that the given request
sets only one of PTP_RISING_EDGE or PTP_FALLING_EDGE, but not both.
However, this driver does not check whether other flags (such as
PTP_EXT_OFF) are set, nor whether any future unrecognized flags are set.
Fix this by adding the appropriate check to the lan743x_ptp_io_extts()
function.
Fixes: 60942c397a ("net: lan743x: Add support for PTP-IO Event Input External Timestamp (extts)")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250312-jk-net-fixes-supported-extts-flags-v2-3-ea930ba82459@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/d8f0e09bfa4bd4850e363645cc634afeb5779b88.1738746872.git.namcao@linutronix.de
As all PCS are using the neg_mode parameter rather than the legacy
an_mode, remove the ability to use the legacy an_mode. We remove the
tests in the phylink code, unconditionally passing the PCS neg_mode
parameter to PCS methods, and remove setting the flag from drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tidPn-0040hd-2R@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert lan743x to phylink managed EEE:
- Set the lpi_capabilties.
- Move the call to lan743x_mac_eee_enable() into the enable/disable
tx_lpi functions.
- Ensure that EEEEN is clear during probe.
- Move the setting of the LPI timer into mac_enable_tx_lpi().
- Move reading of LPI timer to phylink initialisation to set the
default timer value.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1tYAEB-0014QB-4s@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the netdev that we already have in lan743x_phylink_mac_link_down().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1tYAE5-0014Q5-Up@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The lan969x switch device supports manual frame injection and extraction
to and from the switch core, using a number of injection and extraction
queues. This technique is currently supported, but delivers poor
performance compared to Frame DMA (FDMA).
This lan969x implementation of FDMA, hooks into the existing FDMA for
Sparx5, but requires its own RX and TX handling, as lan969x does not
support the same native cache coherency that Sparx5 does. Effectively,
this means that we are going to use the DMA mapping API for mapping and
unmapping TX buffers. The RX loop will utilize the page pool API for
efficient RX handling. Other than that, the implementation is largely
the same, and utilizes the FDMA library for DCB and DB handling.
Some numbers:
Manual injection/extraction (before this series):
// iperf3 -c 1.0.1.1
[ ID] Interval Transfer Bitrate
[ 5] 0.00-10.02 sec 345 MBytes 289 Mbits/sec sender
[ 5] 0.00-10.06 sec 345 MBytes 288 Mbits/sec receiver
FDMA (after this series):
// iperf3 -c 1.0.1.1
[ ID] Interval Transfer Bitrate
[ 5] 0.00-10.03 sec 1.10 GBytes 940 Mbits/sec sender
[ 5] 0.00-10.07 sec 1.10 GBytes 936 Mbits/sec receiver
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20250113-sparx5-lan969x-switch-driver-5-v2-5-c468f02fd623@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We are going to implement the RX and TX paths a bit differently on
lan969x and therefore need to introduce new ops for FDMA functions:
init, deinit, xmit and poll. Assign the Sparx5 equivalents for these and
update the code throughout. Also add a 'struct net_device' argument to
the xmit() function, as we will be needing that for lan969x.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20250113-sparx5-lan969x-switch-driver-5-v2-4-c468f02fd623@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function sparx5_fdma_tx_activate() is responsible for configuring
the TX FDMA instance and activating the channel. TX activation has
previously been done in the xmit() function, when the first frame is
transmitted. Now that we have separate functions for starting and
stopping the FDMA, it seems reasonable to move the TX activation to the
start function. This change has no implications on the functionality.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20250113-sparx5-lan969x-switch-driver-5-v2-3-c468f02fd623@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The two functions: sparx5_fdma_{start(),stop()} are responsible for a
number of things, namely: allocation and initialization of FDMA buffers,
activation FDMA channels in hardware and activation of the NAPI
instance.
This patch splits the buffer allocation and initialization into init and
deinit functions, and the channel and NAPI activation into start and
stop functions. This serves two purposes: 1) the start() and stop()
functions can be reused for lan969x and 2) prepares for future MTU
change support, where we must be able to stop and start the FDMA
channels and NAPI instance, without free'ing and reallocating the FDMA
buffers.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20250113-sparx5-lan969x-switch-driver-5-v2-2-c468f02fd623@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a previous series, we made sure that FDMA was not initialized and
started on lan969x. Now that we are going to support it, undo that
change. In addition, make sure the chip ID check is only applicable on
Sparx5, as this is a check that is only relevant on this platform.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20250113-sparx5-lan969x-switch-driver-5-v2-1-c468f02fd623@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass the current neg_mode into phylink_mii_c22_pcs_get_state() and
phylink_mii_c22_pcs_decode_state(). Update all users of phylink PCS
that use these functions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGeY-000Et9-8g@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass the current neg_mode into the .pcs_get_state() method. Update all
users of phylink PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGeT-000Et3-4L@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The lan969x switch device includes two RGMII port interfaces (port 28
and 29) supporting data speeds of 1 Gbps, 100 Mbps and 10 Mbps. MAC
level delays are configurable through the HSIO_WRAP target, by choosing
a phase shift selector, corresponding to a certain time delay in nano
seconds.
Add new file: lan969x_rgmii.c that contains the implementation for
configuring the RGMII port devices. MAC level delays are configured
using the "{rx,tx}-internal-delay-ps" properties. These properties must
be specified independently of the phy-mode. If missing, or set to zero,
the MAC will not apply any delay.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Tested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241220-sparx5-lan969x-switch-driver-4-v5-8-fa8ba5dff732@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Configuration of RGMII is done by configuring the GPIO and clock
settings in the HSIOWRAP target, and configuring the RGMII port devices
in the DEVRGMII target. Both targets contain registers replicated for
the number of RGMII port devices, which is two.
Add said targets and register macros required to configure RGMII.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Tested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241220-sparx5-lan969x-switch-driver-4-v5-7-fa8ba5dff732@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When doing a port config, we verify the port speed against the PHY mode
and supported speeds of that PHY mode. Add checks for the four RGMII phy
modes: RGMII, RGMII_ID, RGMII_TXID and RGMII_RXID.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Tested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241220-sparx5-lan969x-switch-driver-4-v5-6-fa8ba5dff732@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RGMII ports have no PCS to configure. Make sure we only return the
PCS for port modes that require it.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241220-sparx5-lan969x-switch-driver-4-v5-5-fa8ba5dff732@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When doing a port config, we configure low-speed port devices, among
other things. We have a check to ensure, that the device is indeed a
low-speed device, an not a high-speed device. Add an additional check,
to ensure that the device is not an RGMII device.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Tested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241220-sparx5-lan969x-switch-driver-4-v5-4-fa8ba5dff732@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that we can check if a given port is an RGMII port, use it in the
following cases:
- To set RGMII PHY modes for RGMII port devices.
- To avoid checking for a SerDes node in the devicetree, when the port
is an RGMII port.
- To bail out of sparx5_port_init() when the common configuration is
done.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Tested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241220-sparx5-lan969x-switch-driver-4-v5-3-fa8ba5dff732@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The lan969x device contains two RGMII port interfaces, sitting at port
28 and 29. Add function: is_port_rgmii() to the match data ops, that
checks if a given port is an RGMII port or not. For Sparx5, this
function always returns false.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Tested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241220-sparx5-lan969x-switch-driver-4-v5-2-fa8ba5dff732@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sparx5_port_init() does initial configuration of a variety of
different features and options for each port. Some are shared for all
types of devices, some are not. As it is now, common configuration is
done after configuration of low-speed devices. This will not work when
adding RGMII support in a subsequent patch.
In preparation for lan969x RGMII support, move a block of code, that
configures 2g5 devices, down. This ensures that the configuration common
to all devices is done before configuration of 2g5, 5g, 10g and 25g
devices.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Tested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241220-sparx5-lan969x-switch-driver-4-v5-1-fa8ba5dff732@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On port initialization, we configure the maximum frame length accepted
by the receive module associated with the port. This value is currently
written to the MAX_LEN field of the DEV10G_MAC_ENA_CFG register, when in
fact, it should be written to the DEV10G_MAC_MAXLEN_CFG register. Fix
this.
Fixes: 946e7fd505 ("net: sparx5: add port module support")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing port mirroring, the physical port to send the frame to, is
written to the FRMC_PORT_VAL field of the QFWD_FRAME_COPY_CFG register.
This field is 7 bits wide on sparx5 and 6 bits wide on lan969x, and has
a default value of 65 and 30, respectively (the number of front ports).
On mirror deletion, we set the default value of the monitor port to
65 for this field, in case no more ports exists for the mirror. Needless
to say, this will not fit the 6 bits on lan969x.
Fix this by correctly using the n_ports constant instead.
Fixes: 3f9e46347a ("net: sparx5: use SPX5_CONST for constants which already have a symbol")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FDMA handler is responsible for scheduling a NAPI poll, which will
eventually fetch RX packets from the FDMA queue. Currently, the FDMA
handler is run in a threaded context. For some reason, this kills
performance. Admittedly, I did not do a thorough investigation to see
exactly what causes the issue, however, I noticed that in the other
driver utilizing the same FDMA engine, we run the FDMA handler in hard
IRQ context.
Fix this performance issue, by running the FDMA handler in hard IRQ
context, not deferring any work to a thread.
Prior to this change, the RX UDP performance was:
Interval Transfer Bitrate Jitter
0.00-10.20 sec 44.6 MBytes 36.7 Mbits/sec 0.027 ms
After this change, the rx UDP performance is:
Interval Transfer Bitrate Jitter
0.00-9.12 sec 1.01 GBytes 953 Mbits/sec 0.020 ms
Fixes: 10615907e9 ("net: sparx5: switchdev: adding frame DMA functionality")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depmod reports a cyclic dependency between modules sparx5-switch.ko and
lan969x-switch.ko:
depmod: ERROR: Cycle detected: lan969x_switch -> sparx5_switch -> lan969x_switch
depmod: ERROR: Found 2 modules in dependency cycles!
make[2]: *** [scripts/Makefile.modinst:132: depmod] Error 1
make: *** [Makefile:224: __sub-make] Error 2
This makes sense, as they both require symbols from each other.
Fix this by compiling lan969x support into the sparx5-switch.ko module.
In order to do this, in a sensible way, we move the lan969x/ dir into
the sparx5/ dir and do some code cleanup of code that is no longer
required.
After this patch, depmod will no longer complain, as lan969x support is
compiled into the sparx5-swicth.ko module, and can no longer be compiled
as a standalone module.
Fixes: 98a0111960 ("net: sparx5: add compatible string for lan969x")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VCAP API unit tests fail randomly with errors such as
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:387
Expected 134 + 7 == iter.offset, but
134 + 7 == 141 (0x8d)
iter.offset == 17214 (0x433e)
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:388
Expected 5 == iter.reg_idx, but
iter.reg_idx == 702 (0x2be)
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:389
Expected 11 == iter.reg_bitpos, but
iter.reg_bitpos == 15 (0xf)
# vcap_api_iterator_init_test: pass:0 fail:1 skip:0 total:1
Comments in the code state that "A typegroup table ends with an all-zero
terminator". Add the missing terminators.
Some of the typegroups did have a terminator of ".offset = 0, .width = 0,
.value = 0,". Replace those terminators with "{ }" (no trailing ',') for
consistency and to excplicitly state "this is a terminator".
Fixes: 67d637516f ("net: microchip: sparx5: Adding KUNIT test for the VCAP API")
Cc: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241119213202.2884639-1-linux@roeck-us.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sparx5 switchdev driver can be built either with or without support
for the Lan969x switch. However, it cannot be built-in when the lan969x
driver is a loadable module because of a link-time dependency:
arm-linux-gnueabi-ld: drivers/net/ethernet/microchip/sparx5/sparx5_main.o:(.rodata+0xd44): undefined reference to `lan969x_desc'
Add a Kconfig dependency to reflect this in Kconfig, allowing all
the valid configurations but forcing sparx5 to be a loadable module
as well if lan969x is.
Fixes: 98a0111960 ("net: sparx5: add compatible string for lan969x")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241113115513.4132548-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add configuration data (for consumption by the VCAP API) for the four
VCAP's that we are going to support. The following VCAP's will be
supported:
- VCAP CLM: (also known as IS0) is part of the analyzer and enables
frame classification using VCAP functionality.
- VCAP IS2: is part of ANA_ACL and enables access control lists, using
VCAP functionality.
- VCAP ES0: is part of the rewriter and enables rewriting of frames
using VCAP functionality.
- VCAP ES2: is part of EACL and enables egress access control lists
using VCAP functionality
The two VCAP's: CLM and IS2 use shared resources from the SUPER VCAP.
The SUPER VCAP is a shared pool of 6 blocks that can be distributed
freely among CLM and IS2. Each block in the pool has 3,072 addresses
with entries, actions, and counters. ES0 and ES2 does not use shared
resources.
In the configuration data for lan969x CLM uses blocks 2-4 with a total
of 6 lookups. IS2 uses blocks 0-1 with a total of 4 lookups.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Platform VCAP data for each VCAP instance is auto-generated using an
internal Microchip tool. The generated VCAP data contains information
about keyfields, keyfield sets, actionfields, actionfield sets and
typegroups, which in combination are used to encode and decode rules in
the VCAP.
Add the auto-generated VCAP file lan969x_vcap_ag_api.c and assign the
two structs: lan969x_vcaps and lan969x_vcap_stats to the match data.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The is_sparx5() check was introduced in an earlier series, to make sure
the sparx5_vcap_init() was not executed on lan969x, as it was not
implemented there yet. Now that it is, remove that check.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In preparation for lan969x VCAP support, add the following three new
VCAP constants to match data:
- vcaps_cfg (contains configuration data for each VCAP).
- vcaps (contains auto-generated information about VCAP keys and
actions).
- vcap_stats: (contains auto-generated string names of all the keys
and actions)
Add these constants to the Sparx5 match data constants and use them to
initialize the VCAP's in sparx5_vcap_init().
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
