[Why]
Due to very small clock register delta between DCN35 and DCN351, clock
spread is being checked on the wrong register for DCN351, causing the
display driver to believe that DPREFCLK downspread to be disabled when
in some stacks it is enabled. This causes the clock values for audio to
be incorrect.
[How]
Both DCN351 and DCN35 use the same clk_mgr, so we modify the DCN35
function that checks for SSC enable to read CLK6 instead of CLK5 when
using DCN351. This allows us to read for DPREFCLK downspread correctly
so the clock can properly compensate when setting values.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Kevin Gao <kevin.gao3@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When BIOS includes a lot of custom brightness data points, walking
the entire list can be time consuming. This is most noticed when
dragging a power slider. The "higher" values are "slower" to drag
around.
[How]
Move custom brightness calculation loop into a static function. Before
starting the loop check the "half way" data point to see how it compares
to the input. If greater than the half way data point use that as the
starting point instead.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Static analysis shows that pointer "timing" cannot be NULL because it
points to the object "struct dc_crtc_timing".
Remove the extra NULL check. It is meaningless and harms the readability
of the code.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Andrey Vatoropin <a.vatoropin@crpt.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removed unused function mpc401_get_3dlut_fast_load_status.
Signed-off-by: James Flowers <bold.zone2373@fastmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
- VUPDATE_NO_LOCK should be used in place of VUPDATE always
- Add VERTICAL_INTERRUPT1 and VERTICAL_INTERRUPT2 definitions
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit fe45e2af4a.
Reason for revert: it causes stuttering in some usecases.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
DCN401 uses a different structure to store the VStartup offset used to
calculate the VUpdate position, so adjust the calculations to use this
value.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In the mode validation, mst dsc is considered for bw calculation after
common dsc config is determined. Currently it considered common dsc config
is found if max and min target bpp are non zero which is not accurate. Invalid
max and min target bpp values would not get max_kbps and min_kbps calculated,
leading to falsefully pass a mode that does not have valid dsc parameters
available.
[how]
Use the return value of decide_dsc_bandwidth_range() to determine whether valid
dsc common config is found or not. Prune out modes that do not have valid common
dsc config determined.
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN4+ supports a new register based mailbox for sending messages
from host to DMCUB. This mailbox supports 64 byte commands, which makes
it compatible with the same structure as the frame buffer based mailbox.
[HOW]
The intention for reg_inbox0 is to be slot in replacement for the frame
buffer based mailbox (Inbox1). It supports all of the required features:
- Supports all messages handled by FB Inbox1
- Supports multi command batching
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Replay need special policy for the scenario Teams,
add a flag to imply apply special policy or not.
[How]
Add a config option intended for future use for video conferencing applications.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: ChunTao Tso <ChunTao.Tso@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm_warn prints the drm device instance which is helpful when
debugging multi gpu issues
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm_info prints the drm device instance which is helpful when
debugging multi gpu issues
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
Core should evaluate support based on the max clocks after considering
downspread.
Reviewed-by: Austin Zheng <austin.zheng@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This array was initially defined as size 50. There were array overflow
issues so the size was increased to 100. To ensure such issues are
avoided in the future, the size should be set based on the possible
contents instead of an arbitrary value.
[How]
- upper bound, assume every update occurs on max number of pipes
- define array sizes for function parameters, for static analysis
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Mapping of ODM enum is different for DML2.0 vs DML2.1.
Configs using DML2.1 will incorrectly trigger an assert meant for DML2.0.
[How]
Use if/else to seperate logic between DML2.0 and DML2.1.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
prefer drm_err instead of DRM_ERROR since the former prints the
associated DRM device, which is helpful when debugging multi-gpu
use cases.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
make the drm device available in create_validate_stream_for_sink()
so that drm_err() can be used
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add amdgpu_device pointer to data associated with the work struct
such that hpd handlers has access to the drm device for use with
drm_err()
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pass in a pointer to amdgpu_device directly to the function.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Access to indirect registers by DC and other components are not synchronized.
[How]
Use sync version of indirect register access.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Create a temporary scratch dc_link for programming purposes
and fix a copy of pipe_ctx on the stack to a pointer reference.
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Signed-off-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
the guard of is_apu not in sync, caused no watermark_c output.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Read the histogram for VariBright validation
[How]
Add dc/dmub functions to read histogram and ACE
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Chun-Liang Chang <Chun-Liang.Chang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It makes DSC enable when we commit the stream which need
keep power off.And then it will skip to disable DSC if
pipe reset at this situation as power has been off. It may
cause the DSC unexpected enable on the pipe with the
next new stream which doesn't support DSC.
[HOW]
Check the DSC used on current pipe status when update stream.
Skip to enable if it has been off. The operation enable
DSC should happen when set power on.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Paul Hsieh <Paul.Hsieh@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To bring in latest changes in DML21
[List of Changes]
- Unification of DML logging to use DML_LOG_* macro
- Clean up variables that are exclusively used for logging
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
USB4 BW Allocation response will be handled in HPD IRQ.
No need to handle it in DPIA notification callback.
[How]
Remove DP BW allocation response code in DPIA notification.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Cruise <Cruise.Hung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want to output visual confirm color based on stream.
[HOW]
If visual confirm is for DMUB, use DMUB to get color.
Otherwise, find plane with highest layer index, output visual confirm color
of pipe that contains plane with highest index.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Leo Zeng <Leo.Zeng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want to allow the display manager to override the visual
confirm color in DC when required.
[HOW]
Add new visual confirm mode VISUAL_CONFIRM_EXPLICIT, check mode before
setting visual confirm color.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Leo Zeng <Leo.Zeng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HP Elitebook 645 has DP0 and DP1 swapped.
[How]
Add HP Elitebook 645 to DP0/DP1 swap quirk list.
Cc: stable@vger.kernel.org
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3701
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HP Probook 445 and 465 has DP0 and DP1 swapped.
[How]
Add HP Probook 445 and 465 to DP0/DP1 swap quirk list.
Cc: stable@vger.kernel.org
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3995
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Anson Tsao <anson.tsao@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Replay and PSR will cause some video corruption while VRR is enabled.
[How]
Do not enable the Replay and PSR while VRR is active in
amdgpu_dm_enable_self_refresh().
Fixes: 67edb81d6e ("drm/amd/display: Disable replay and psr while VRR is enabled")
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
bridge:
- tda998x: Select CONFIG_DRM_KMS_HELPER
amdgpu:
- Guard against potential division by 0 in fan code
- Zero RPM support for SMU 14.0.2
- Properly handle SI and CIK support being disabled
- PSR fixes
- DML2 fixes
- DP Link training fix
- Vblank fixes
- RAS fixes
- Partitioning fix
- SDMA fix
- SMU 13.0.x fixes
- Rom fetching fix
- MES fixes
- Queue reset fix
xe:
- Fix NULL pointer dereference on error path
- Add missing HW workaround for BMG
- Fix survivability mode not triggering
- Fix build warning when DRM_FBDEV_EMULATION is not set
i915:
- Bounds check for scalers in DSC prefill latency computation
- Fix build by adding a missing include
adp:
- Fix error handling in plane setup
-----BEGIN PGP SIGNATURE-----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=P/sW
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2025-04-05' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Weekly fixes, mostly from the end of last week, this week was very
quiet, maybe you scared everyone away. It's mostly amdgpu, and xe,
with some i915, adp and bridge bits, since I think this is overly
quiet I'd expect rc2 to be a bit more lively.
bridge:
- tda998x: Select CONFIG_DRM_KMS_HELPER
amdgpu:
- Guard against potential division by 0 in fan code
- Zero RPM support for SMU 14.0.2
- Properly handle SI and CIK support being disabled
- PSR fixes
- DML2 fixes
- DP Link training fix
- Vblank fixes
- RAS fixes
- Partitioning fix
- SDMA fix
- SMU 13.0.x fixes
- Rom fetching fix
- MES fixes
- Queue reset fix
xe:
- Fix NULL pointer dereference on error path
- Add missing HW workaround for BMG
- Fix survivability mode not triggering
- Fix build warning when DRM_FBDEV_EMULATION is not set
i915:
- Bounds check for scalers in DSC prefill latency computation
- Fix build by adding a missing include
adp:
- Fix error handling in plane setup"
# -----BEGIN PGP SIGNATURE-----
* tag 'drm-next-2025-04-05' of https://gitlab.freedesktop.org/drm/kernel: (34 commits)
drm/i2c: tda998x: select CONFIG_DRM_KMS_HELPER
drm/amdgpu/gfx12: fix num_mec
drm/amdgpu/gfx11: fix num_mec
drm/amd/pm: Add gpu_metrics_v1_8
drm/amdgpu: Prefer shadow rom when available
drm/amd/pm: Update smu metrics table for smu_v13_0_6
drm/amd/pm: Remove host limit metrics support
Remove unnecessary firmware version check for gc v9_4_2
drm/amdgpu: stop unmapping MQD for kernel queues v3
Revert "drm/amdgpu/sdma_v4_4_2: update VM flush implementation for SDMA"
drm/amdgpu: Parse all deferred errors with UMC aca handle
drm/amdgpu: Update ta ras block
drm/amdgpu: Add NPS2 to DPX compatible mode
drm/amdgpu: Use correct gfx deferred error count
drm/amd/display: Actually do immediate vblank disable
drm/amd/display: prevent hang on link training fail
Revert "drm/amd/display: dml2 soc dscclk use DPM table clk setting"
drm/amd/display: Increase vblank offdelay for PSR panels
drm/amd: Handle being compiled without SI or CIK support better
drm/amd/pm: Add zero RPM enabled OD setting support for SMU14.0.2
...
Here is the big set of driver core updates for 6.15-rc1. Lots of stuff
happened this development cycle, including:
- kernfs scaling changes to make it even faster thanks to rcu
- bin_attribute constify work in many subsystems
- faux bus minor tweaks for the rust bindings
- rust binding updates for driver core, pci, and platform busses,
making more functionaliy available to rust drivers. These are all
due to people actually trying to use the bindings that were in 6.14.
- make Rafael and Danilo full co-maintainers of the driver core
codebase
- other minor fixes and updates.
This has been in linux-next for a while now, with the only reported
issue being some merge conflicts with the rust tree. Depending on which
tree you pull first, you will have conflicts in one of them. The merge
resolution has been in linux-next as an example of what to do, or can be
found here:
https://lore.kernel.org/r/CANiq72n3Xe8JcnEjirDhCwQgvWoE65dddWecXnfdnbrmuah-RQ@mail.gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ+mMrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRgwCdH58OE3BgL0uoFY5vFImStpmPtqUAoL5HpVWI
jtbJ+UuXGsnmO+JVNBEv
=gy6W
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updatesk from Greg KH:
"Here is the big set of driver core updates for 6.15-rc1. Lots of stuff
happened this development cycle, including:
- kernfs scaling changes to make it even faster thanks to rcu
- bin_attribute constify work in many subsystems
- faux bus minor tweaks for the rust bindings
- rust binding updates for driver core, pci, and platform busses,
making more functionaliy available to rust drivers. These are all
due to people actually trying to use the bindings that were in
6.14.
- make Rafael and Danilo full co-maintainers of the driver core
codebase
- other minor fixes and updates"
* tag 'driver-core-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (52 commits)
rust: platform: require Send for Driver trait implementers
rust: pci: require Send for Driver trait implementers
rust: platform: impl Send + Sync for platform::Device
rust: pci: impl Send + Sync for pci::Device
rust: platform: fix unrestricted &mut platform::Device
rust: pci: fix unrestricted &mut pci::Device
rust: device: implement device context marker
rust: pci: use to_result() in enable_device_mem()
MAINTAINERS: driver core: mark Rafael and Danilo as co-maintainers
rust/kernel/faux: mark Registration methods inline
driver core: faux: only create the device if probe() succeeds
rust/faux: Add missing parent argument to Registration::new()
rust/faux: Drop #[repr(transparent)] from faux::Registration
rust: io: fix devres test with new io accessor functions
rust: io: rename `io::Io` accessors
kernfs: Move dput() outside of the RCU section.
efi: rci2: mark bin_attribute as __ro_after_init
rapidio: constify 'struct bin_attribute'
firmware: qemu_fw_cfg: constify 'struct bin_attribute'
powerpc/perf/hv-24x7: Constify 'struct bin_attribute'
...
[Why]
The `vblank_config.offdelay` field follows the same semantics as the
`drm_vblank_offdelay` parameter. Setting it to 0 will never disable
vblank.
[How]
Set `offdelay` to a positive number.
Fixes: e45b6716de ("drm/amd/display: use a more lax vblank enable policy for DCN35+")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
When link training fails, the phy clock will be disabled. However, in
enable_streams, it is assumed that link training succeeded and the
mux selects the phy clock, causing a hang when a register write is made.
[How]
When enable_stream is hit, check if link training failed. If it did, fall
back to the ref clock to avoid a hang and keep the system in a recoverable
state.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Brendan Tam <Brendan.Tam@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[why]
this dscclk use DCN defined per DPM level will cause a DCFCLK increase.
needs to follow up.
This reverts commit 15b959534a
Reviewed-by: Yihan Zhu <yihan.zhu@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Depending on when the HW latching event (vupdate) of double-buffered
registers happen relative to the PSR SDP (signals panel psr enter/exit)
deadline, and how bad the Panel clock has drifted since the last ALPM
off event, there can be up to 3 frames of delay between sending the PSR
exit cmd to DMUB fw, and when the panel starts displaying live frames.
This can manifest as micro-stuttering when userspace commit patterns
cause rapid toggling of the DRM vblank counter, since PSR enter/exit is
hooked up to DRM vblank disable/enable respectively.
In the ideal world, the panel should present the live frame immediately
on PSR exit cmd. But due to HW design and PSR limitations, immediate
exit can only happen by chance, when:
1. PSR exit cmd is ack'd by FW before HW latching (vupdate) event, and
2. Panel's SDP deadline -- determined by it's PSR Start Delay in DPCD
71h -- is after the vupdate event. The PSR exit SDP can then be sent
immediately after HW latches. Otherwise, we have to wait 1 frame. And
3. There is negligible drift between the panel's clock and source clock.
Otherwise, there can be up to 1 frame of drift.
Note that this delay is not expected with Panel Replay.
[How]
Since PSR power savings can be quite substantial, and there are a lot of
systems in the wild with PSR panels, It'll be nice to have a middle
ground that balances user experience with power savings.
A simple way to achieve this is by extending the vblank offdelay, such
that additional PSR exit delays will be less perceivable.
We can set:
20/100 * offdelay_ms = 3_frames_ms
=> offdelay_ms = 5 * 3_frames_ms
This ensures that `3_frames_ms` will only be experienced as a 20% delay
on top how long the panel has been static, and thus make the delay
less perceivable.
If this ends up being too high of a percentage, it can be dropped
further in a future change.
Fixes: 537ef0f888 ("drm/amd/display: use new vblank enable policy for DCN35+")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This version brings along following fixes:
- Use DPM table clk setting for dml2 soc dscclk
- Update static soc table
- Fix incorrect fw_state address in dmub_srv
- Use HW lock mgr for PSR1 when only one eDP
- Revert "Support for reg inbox0 for host->DMUB CMDs"
- Change notification of link BW allocation
- Fix message for support_edp0_on_dp1
- Guard against setting dispclk low for dcn31x
- Prevent VStartup Overflow
- Check pipe->stream before passing it to a function
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Not like dppclk/dispclk, dml2 will calculate the minimum required clocks.
For dscclk, it is used for pure comparision.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Update the static soc table dcn3_5_soc.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The fw_state in dmub_srv was assigned with wrong address.
The address was pointed to the firmware region.
[HOW]
Fix the firmware state by using DMUB_DEBUG_FW_STATE_OFFSET
in dmub_cmd.h.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Lo-an Chen <lo-an.chen@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DMUB locking is important to make sure that registers aren't accessed
while in PSR. Previously it was enabled but caused a deadlock in
situations with multiple eDP panels.
[HOW]
Detect if multiple eDP panels are in use to decide whether to use
lock. Refactor the function so that the first check is for PSR-SU
and then replay is in use to prevent having to look up number
of eDP panels for those configurations.
Fixes: f245b400a2 ("Revert "drm/amd/display: Use HW lock mgr for PSR1"")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3965
Reviewed-by: ChiaHsuan Chung <chiahsuan.chung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 15d1c2e6bf.
Reason: Cursor movement causes system to hang.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
The response of DP BW allocation is handled in Outbox ISR.
When it failed to request the DP BW allocation, it sent another
DPCD request in Outbox ISR immediately. The DP AUX reply also
uses the Outbox ISR. So, no AUX reply happened in this case.
Change to use HPD IRQ for the notification.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The info message was wrong when support_edp0_on_dp1 is enabled
[HOW]
Use correct info message for support_edp0_on_dp1
Fixes: f6d17270d1 ("drm/amd/display: add a quirk to enable eDP0 on DP1")
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Yilin Chen <Yilin.Chen@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We should never apply a minimum dispclk value while in
prepare_bandwidth or while displays are active. This is
always an optimizaiton for when all displays are disabled.
[HOW]
Defer dispclk optimization until safe_to_lower = true
and display_count reaches 0.
Since 0 has a special value in this logic (ie. no dispclk
required) we also need adjust the logic that clamps it for
the actual request to PMFW.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <chris.park@amd.com>
Reviewed-by: Eric Yang <eric.yang@amd.com>
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Fixed Overflow issue by clamping VStartup to max value of register.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
dp_is_128b_132b_signal dereferences pipe->stream so it is necessary to
check it in advance.
Also fix erroneous spaces and move a variable declaration to top.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This macro guard "__cplusplus" is unnecessary and should not be there.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are trying to get rid of all multiplications from allocation
functions to prevent integer overflows. Here the multiplication is
probably safe, but using kcalloc() is more appropriate and improves
readability. This patch has no effect on runtime behavior.
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ethan Carter Edwards <ethan@ethancedwards.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are trying to get rid of all multiplications from allocation
functions to prevent integer overflows. Here the multiplication is
probably safe, but using kcalloc() is more appropriate and improves
readability. This patch has no effect on runtime behavior.
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ethan Carter Edwards <ethan@ethancedwards.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are trying to get rid of all multiplications from allocation
functions to prevent integer overflows. Here the multiplication is
probably safe, but using kcalloc() is more appropriate and improves
readability. This patch has no effect on runtime behavior.
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ethan Carter Edwards <ethan@ethancedwards.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are trying to get rid of all multiplications from allocation
functions to prevent integer overflows. Here the multiplication is
probably safe, but using kcalloc() is more appropriate and improves
readability. This patch has no effect on runtime behavior.
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ethan Carter Edwards <ethan@ethancedwards.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Fix some Replay/PSR issue
- Fix backlight brightness
- Fix suspend issue
- Fix visual confirm color
- Add scoped mutexes for amdgpu_dm_dhcp
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
1. apply oem panel timing (not only on OLED)
2. remove MIN_DPP_DISP_CLK request in driver.
This fix will apply for dcn31x but not
sync with DML's output.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
enable_assr() has a res variable that only is changed in one block with
no cleanup necessary.
[How]
Remove variable and return early from failure cases.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Guards automatically release mutex when it goes out of scope making
code easier to follow.
[How]
Replace all use of mutex_lock()/mutex_unlock() with guard(mutex).
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A slab-use-after-free is reported when HDCP is destroyed but the
property_validate_dwork queue is still running.
[How]
Cancel the delayed work when destroying workqueue.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4006
Fixes: da3fd7ac0b ("drm/amd/display: Update CP property based on HW query")
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some VR headsets with large blanks, it's possible
to overflow the OTG_VSTARTUP_PARAM:VSTARTUP_START
register. This can lead to incorrect DML calculations
and underflow downstream.
[How]
Min the calcualted max_vstartup_lines with the max
value of the register.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
stream->adjust will be overwritten by update->crtc_timing_adjust.
We should set update->crtc_timing_adjust->timing_adjust_pending
and then overwrite stream->adjust.
Reset update->crtc_timing_adjust->timing_adjust_pending after
the assignment.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Zhongwei Zhang <Zhongwei.Zhang@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In some cases the remain de-tile buffer segments will be greater
than zero if we don't add the non-top pipe to calculate, at
this time the override de-tile buffer size will be valid and used.
But it makes the de-tile buffer segments used finally for all of pipes
exceed the maximum.
[HOW]
Add the non-top pipe to calculate the remain de-tile buffer segments.
Don't set override size to use the average according to pipe count
if the value exceed the maximum.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Sometimes visual confirm color is updated, but the
background color is not changed. This causes visual
confrim to show incorrect colors.
[HOW]
Update background color when visual confirm color changes.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Leo Zeng <Leo.Zeng@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
A warning message "WARNING: CPU: 4 PID: 459 at ... /dc_resource.c:3397
calculate_phy_pix_clks+0xef/0x100 [amdgpu]" occurs because the
display_color_depth == COLOR_DEPTH_141414 is not handled. This is
observed in Radeon RX 6600 XT.
It is fixed by assigning pix_clk * (14 * 3) / 24 - same as the rests.
Also fixes the indentation in get_norm_pix_clk.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN4+ supports a new register based mailbox for sending messages
from host to DMCUB. This mailbox supports 64 byte commands, which makes
it compatible with the same structure as the frame buffer based mailbox.
[HOW]
The intention for reg_inbox0 is to be slot in replacement for the frame
buffer based mailbox (Inbox1). It supports all of the required features:
- Supports all messages handled by FB Inbox1
- Supports multi command batching
Reviewed-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The clear_dsc_setting at boot logic was based on dcn version
check.
As such new ASIC lost this DSC clear up logic, change the
assumption to BIOS support eDP DSC for new ASIC.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
DP spec has been updated recently to make regulated autonomous mode more
well-defined. In case any PCON vendors choose to implement regulated
autonomous mode in the future, pre-emptively add handling for the
regulated autonomous mode based on current spec.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DP tunneling should not abort link train even bandwidth become
too low after downgrade. Otherwise, it would fail compliance test.
[HOW}
Do link train with downgrade settings even bandwidth is not enough
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Vtotal is not applied to HW when handling vsync interrupt.
Make sure vtotal is aligned before enable replay.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Reviewed-by: Robin Chen <robin.chen@amd.com>
Signed-off-by: Danny Wang <danny.wang@amd.com>
Signed-off-by: Zhongwei Zhang <Zhongwei.Zhang@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The displays currently don't get turned off until after other IP blocks
have been suspended. However turning off the displays first gives a
very visible response that the system is on it's way down.
[How]
Turn off displays in a prepare_suspend() callback instead when possible.
This will help for suspend and hibernate sequences.
The shutdown sequence however will not call prepare() so check whether
the state has been already saved to decide what to do.
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
GPU reset will attempt to restore cached state, but brightness doesn't
get restored. It will come back at 100% brightness, but userspace thinks
it's the previous value.
[How]
When running resume sequence if GPU is in reset restore brightness
to previous value.
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To avoid flickering during boot default brightness level set by BIOS
should be maintained for as much of the boot as feasible.
commit 2fe87f54ab ("drm/amd/display: Set default brightness according
to ACPI") attempted to set the right levels for AC vs DC, but brightness
still got reset to maximum level in initialization code for
setup_backlight_device().
[How]
Remove the hardcoded initialization in setup_backlight_device() and
instead program brightness value to match BIOS (AC or DC). This avoids a
brightness flicker from kernel changing the value. Userspace may however
still change it during boot.
Fixes: 2fe87f54ab ("drm/amd/display: Set default brightness according to ACPI")
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When analyzing some crash dumps, not all of the expected DMUB info was
available, so we want to add in-object storage for this data.
[How]
- dmub_srv_debug (renamed to dmub_timeout_info) is already a member of
dmub_diagnostic_data, therefore keep a dmub_diagnostic_data directly in
dmub_srv
- use dmub_srv->debug when collecting diagnostic info instead of stack
object to allow for easy inspection in crash dumps
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It seems HPD interrupts are enabled by default for all connectors, even
if the hpd source isn't valid. An eDP for example, does not have a valid
hpd source (but does have a valid hpdrx source; see construct_phy()).
Thus, eDPs should have their hpd interrupt disabled.
In the past, this wasn't really an issue. Although the driver gets
interrupted, then acks by writing to hw registers, there weren't any
subscribed handlers that did anything meaningful (see
register_hpd_handlers()).
But things changed with the introduction of IPS. s2idle requires that
the driver allows IPS for DMUB fw to put hw to sleep. Since register
access requires hw to be awake, the driver will block IPS entry to do
so. And no IPS means no hw sleep during s2idle.
This was the observation on DCN35 systems with an eDP. During suspend,
the eDP toggled its hpd pin as part of the panel power down sequence.
The driver was then interrupted, and acked by writing to registers,
blocking IPS entry.
[How]
Since DC marks eDP connections as having invalid hpd sources (see
construct_phy()), DM should disable them at the hw level. Do so in
amdgpu_dm_hpd_init() by disabling all hpd ints first, then selectively
enabling ones for connectors that have valid hpd sources.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When switching between PSR/Replay,
the DPCD config of previous mode is not cleared,
resulting in unexpected behavior in TCON.
[How]
Initialize the DPCD in setup function
Reviewed-by: Robin Chen <robin.chen@amd.com>
Signed-off-by: Leon Huang <Leon.Huang1@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hw supports it.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmfOKBUeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1aQH/iC+Oyij4VxAjBek
BOXIT/p6CwlIXb8ObiWWcRjDPizlcxb3RaV8J2RO+IqaQ2wltxpFANq2G7Re2FPm
SNcEpIURAOVcxHGedcfFA91srO5F4FzNTO8LVp7MIbcgMYy3pdk+dbZmi6A691R+
t9pb74m+MAnF1o/MUx7pUlhAT/4ymuuR0F7WCSg4h0Xwe5m0nlJY89kJBC7PCjyd
n3mdhsz3rDSLmt/z/T7HGD89r8sYSvm9cOKtL3ELgGTrm7boQV8ii9Y9w04DI8PQ
JmIernugcCxmhH36mVUAHgJf2+/T388xFUh/D5+skeUOUZpaJZG866rnb32WpsHc
eWLFUeg=
=Wypt
-----END PGP SIGNATURE-----
Merge 6.14-rc6 into driver-core-next
We need the driver core fix in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When userspace invokes S4 the flow is:
1) amdgpu_pmops_prepare()
2) amdgpu_pmops_freeze()
3) Create hibernation image
4) amdgpu_pmops_thaw()
5) Write out image to disk
6) Turn off system
Then on resume amdgpu_pmops_restore() is called.
This flow has a problem that because amdgpu_pmops_thaw() is called
it will call amdgpu_device_resume() which will resume all of the GPU.
This includes turning the display hardware back on and discovering
connectors again.
This is an unexpected experience for the display to turn back on.
Adjust the flow so that during the S4 sequence display hardware is
not turned back on.
Reported-by: Xaver Hugl <xaver.hugl@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2038
Cc: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Link: https://lore.kernel.org/r/20250306185124.44780-1-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Starting from 6.11, AMDGPU driver, while being loaded with amdgpu.dc=1,
due to lack of .is_two_pixels_per_container function in dce60_tg_funcs,
causes a NULL pointer dereference on PCs with old GPUs, such as R9 280X.
So this fix adds missing .is_two_pixels_per_container to dce60_tg_funcs.
Reported-by: Rosen Penev <rosenp@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3942
Fixes: e6a901a008 ("drm/amd/display: use even ODM slice width for two pixels per container")
Signed-off-by: Aliaksei Urbanski <aliaksei.urbanski@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We advertise DCC as supported for NV12/P010 formats on GFX12,
but it would fail on this check on atomic commit.
Signed-off-by: David Rosca <david.rosca@amd.com>
Reviewed-by: Ruijing Dong <ruijing.dong@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Null pointer dereference issue could occur when pipe_ctx->plane_state
is null. The fix adds a check to ensure 'pipe_ctx->plane_state' is not
null before accessing. This prevents a null pointer dereference.
Found by code review.
Fixes: 3be5262e35 ("drm/amd/display: Rename more dc_surface stuff to plane_state")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 63e6a77ccf)
Cc: stable@vger.kernel.org
drm_* macros are more helpful that DRM_* macros since the former
indicates the associated DRM device that prints the error, which maybe
helpful when debugging.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement w/a for a panel which requires 10s delay after link detect.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
print__rq_dlg_params_st() was added in 2017 by
commit 061bfa06a4 ("drm/amdgpu/display: Add dml support for DCN")
but has remained unused.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pre_surface_trace() has been unused since 2017's
commit 745cc746da ("drm/amd/display: remove
dc_pre_update_surfaces_to_stream from dc use")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Upgrading the kernel may cause some systems that were previously not using
a firmware specified brightness curve to use one.
In the event of problems with this curve (for example an interpolation
error) add a new dcdebugmask value that can be used to turn it off. Also
add an info message to show that custom brightness curves are currently in
use.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Link: https://lore.kernel.org/r/20250228185145.186319-6-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some systems specify in the firmware a brightness curve that better
reflects the characteristics of the panel used. This is done in the
form of data points and matching luminance percentage.
When converting a userspace requested brightness value use that curve
to convert to a firmware intended brightness value.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Link: https://lore.kernel.org/r/20250228185145.186319-5-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Making a copy of the backlight caps structure between uses is unnecessary.
Refer to pointers to the same structure when using it.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Link: https://lore.kernel.org/r/20250228185145.186319-4-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The ATIF method on some systems will provide a backlight curve. Pass
this curve into amdgpu_dm add it to the structures.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Link: https://lore.kernel.org/r/20250228185145.186319-3-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Various cleanups to amdgpu dm
- Add DP tunneling IRQ handler
- Fix display corruption for dcn35
- Fix dmcub reset problem
- Adjust BW determination for PCON
- DIO encoder refactor
- Fix performance with SubVP under gaming
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm_err() will show which device has the error.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Scoped guards will release the mutex when they go out of scope.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
By using a _free() macro multiple duplicated snippets of code to free
the sink can be dropped. The sink will be released when leaving scope.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A scoped guard will release the mutex when it goes out of scope.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Using a _free(kfree) macro drops the need for a goto statement
as it will be freed when it goes out of scope.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_dm_irq_resume_early() and amdgpu_dm_irq_resume_late() don't
have any error flows. Change the return type from integer to void.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm_dbg() is helpful to show which device had the debug statement.
Adjust to using this instead for debug messages.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Scoped guards will release the mutex when they go out of scope.
Adjust the code to use these instead.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm_err() is helpful to show which device had the error. Adjust to
using this instead for error messages.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All cases except a failure to create a copy of the current context will
call dc_state_release() on the copied context.
Use a _free() macro to free the context and then adjust the error handling
flow to drop the unnecessary use of goto statements.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_dm_commit_zero_streams() returns a DC error code that isn't
checked. Add an explicit check to this and fail dm_suspend() if it
is not DC_OK.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The `ret` variable in dm_suspend() doesn't get set and is just used
to return 0. Drop the needless declaration.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_dm_irq_suspend() doesn't have any error flows and always
returns zero.
Change the function to void.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
USB4 DP BW Allocation uses DP_TUNNELING_IRQ to indicate the status update.
The DP_TUNNELING_IRQ is defined in LINK_SERVICE_IRQ_VECTOR_ESI0. When
receiving DP HPD IRQ in USB4, read the LINK_SERVICE_IRQ_VECTOR_ESI0.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want to add a visual confirm mode for DCC and MCache for
debugging purpose.
[HOW]
color pipes based on whether DCC is enabled and what MCache id
is used.
black - DCC disabled
red - DCC enabled
grey - 2 different MCaches used
other colors - 1 MCache used
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Leo Zeng <Leo.Zeng@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If we soft reset before halt finishes and there are outstanding
memory transactions then the memory interface may produce unexpected
results, such as out of order transactions when the firmware next runs.
These can manifest as random or unexpected load/store violations.
[How]
Increase the timeout before soft reset to ensure the DMCUB has quiesced.
This is effectively 1s maximum based on experimentation.
Use the enable bit check on DCN31 like we're doing on DCN35 and reorder
the reset writes to follow the HW programming guide.
Ensure we're reading SCRATCH7 instead of SCRATCH8 for the HALT code.
No current versions of DMCUB firmware use the SCRATCH8 boot bit to
dynamically switch where the HALT code goes to maintain backwards
compatibility with PSP.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 50f040c53e ("drm/amd/display: Increase halt
timeout for DMCUB to 1s")
There's two issues here:
1. Each poll is closer to 10us than 1us so it stalls for 15s on PNP.
2. We're reading the wrong scratch register to check for the HALT code.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
amdgpu_dm_find_first_crtc_matching_connector can return NULL.
It is necessary to the returned connector before passing it
drm_atomic_get_new_connector_state which always assumes connector is
not NULL.
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
The struct is not and will not be used, as it is no longer relevant nor
supported.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
Certain PCON will clear the FRL_MODE bit despite supporting the link BW
indicated in the other bits.
Thus, skip checking the FRL_MODE bit when interpreting the
hdmi_encoded_link_bw struct.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
These are left required changes for dio encoder refactor.
[HOW]
1. original logic is separated by config option
2. new link encoder dp enable/disable code for dcn35
3. process fec only for DP 8b10b encoding
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Read if panel support multi-sst links
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Hansen Dsouza <Hansen.Dsouza@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It should no longer use DMCUB_SOFT_RESET as it can result
in the memory request path becoming desynchronized.
[HOW]
To ensure robustness in the reset sequence:
1) Extend timeout on the "halt" command sent via gpint, and check for
controller to enter "wait" as a stronger guarantee that there are no
requests to memory still in flight.
2) Remove usage of DMCUB_SOFT_RESET
3) Rely on PSP to reset the controller safely
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
P-state type would remain on previously used when unsupported which
causes confusion in logging and visual confirm, so set back to zero
when unsupported.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When SubVP is active the HW cursor size is limited to 64x64, and
anything larger will force composition which is bad for gaming on
DCN3.2 if the game uses a larger cursor.
[how]
If HW cursor is requested, typically by a fullscreen game, do not
enable SubVP so that up to 256x256 cursor sizes are available for
DCN3.2.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a type mismatch between what CalculateDynamicMetadataParameters()
takes and what is passed to it. Currently this function accepts several
args as signed long but it's called with unsigned integers and integer. On
some systems where long is 32 bits and one of these unsigned int params is
greater than INT_MAX it may cause passing input params as negative values.
Fix this by changing these argument types from long to unsigned int and to
int respectively. Also this will align the function's definition with
similar functions in other dcn* drivers.
Found by Linux Verification Center (linuxtesting.org) with Svace.
Fixes: 6725a88f88 ("drm/amd/display: Add DCN3 DML")
Signed-off-by: Vitaliy Shevtsov <v.shevtsov@mt-integration.ru>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Null pointer dereference issue could occur when pipe_ctx->plane_state
is null. The fix adds a check to ensure 'pipe_ctx->plane_state' is not
null before accessing. This prevents a null pointer dereference.
Found by code review.
Fixes: 3be5262e35 ("drm/amd/display: Rename more dc_surface stuff to plane_state")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The last use of optc3_fpu_set_vrr_m_const() was removed in 2022's
commit 64f991590f ("drm/amd/display: Fix a compilation failure on PowerPC
caused by FPU code")
which removed the only caller (with a similar) name.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All dce command_table_helper's shares a copy-pasted collection
of copy-pasted functions, which are: phy_id_to_atom,
clock_source_id_to_atom_phy_clk_src_id, and engine_bp_to_atom.
This patch removes the multiple copy-pasted by moving them to
the command_table_helper.c and make the command_table_helper's
calls the functions implemented by the command_table_helper.c
instead.
The changes were not tested on actual hardware. I am only able
to verify that the changes keep the code compileable and do my
best to to look repeatedly if I am not actually changing any code.
This is the version 4 of the PATCH, fixed comments about
licence in the new files and the matches From email to
Signed-off-by email. Fixed comments about using
command_table_helper instead of creating a dce_common
Signed-off-by: Luan Icaro Pinto Arcanjo <luanicaro@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC is not using amdgpu_irq_get/put to manage the HPD interrupt refcounts.
So when amdgpu_irq_gpu_reset_resume_helper() reprograms all of the IRQs,
HPD gets disabled.
[How]
Use amdgpu_irq_get/put() for HPD init/fini in DM in order to sync refcounts
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f3dde2ff7f)
Cc: stable@vger.kernel.org
[why]
some board designs have eDP0 connected to DP1, need a way to enable
support_edp0_on_dp1 flag, otherwise edp related features cannot work
[how]
do a dmi check during dm initialization to identify systems that
require support_edp0_on_dp1. Optimize quirk table with callback
functions to set quirk entries, retrieve_dmi_info can set quirks
according to quirk entries
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Yilin Chen <Yilin.Chen@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f6d17270d1)
Cc: stable@vger.kernel.org
[Why]
PSR-SU may cause some glitching randomly on several panels.
[How]
Temporarily disable the PSR-SU and fallback to PSR1 for
all eDP panels.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3388
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 6deeefb820)
Cc: stable@vger.kernel.org
When switching to drm_edid, we slightly changed how to get edid by
removing the possibility of getting them from dc_link when in aux
transaction mode. As MST doesn't initialize the connector with
`drm_connector_init_with_ddc()`, restore the original behavior to avoid
functional changes.
v2:
- Fix build warning of unchecked dereference (kernel test bot)
CC: Alex Hung <alex.hung@amd.com>
CC: Mario Limonciello <mario.limonciello@amd.com>
CC: Roman Li <Roman.Li@amd.com>
CC: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Fixes: 48edb2a425 ("drm/amd/display: switch amdgpu_dm_connector to use struct drm_edid")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 81262b1656)
- Disable PSR-SU on eDP panels
- Fix HPD after GPU reset
- Fixes on dcn4x init, DML2 state policy on DCN36
- Various minor logic fixes
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC is not using amdgpu_irq_get/put to manage the HPD interrupt refcounts.
So when amdgpu_irq_gpu_reset_resume_helper() reprograms all of the IRQs,
HPD gets disabled.
[How]
Use amdgpu_irq_get/put() for HPD init/fini in DM in order to sync refcounts
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Transitioning from low to high resolutions at high refresh rates caused grey corruption.
During the transition state, there is a period where plane size is based on low resultion
state and ODM slices are based on high resoultion state, causing the entire plane to be
contained in one ODM slice. DML2 would turn off the pipe for the ODM slice with no plane,
causing an underflow since the pixel rate for the higher resolution cannot be supported on
one pipe. This change stops DML2 from turning off pipes that are mapped to an ODM slice
with no plane. This is possible to do without negative consequences because pipes can now
take the minimum viewport and draw with zero recout size, removing the need to have the
pipe turned off.
[How]
In map_pipes_from_plane(), remove "check" that skips ODM slices that are not covered by
the plane. This prevents the pipes for those ODM slices from being freed.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Mike Katsnelson <mike.katsnelson@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If we soft reset before halt finishes and there are outstanding
memory transactions then the memory interface may produce unexpected
results, such as out of order transactions when the firmware next runs.
These can manifest as random or unexpected load/store violations.
[How]
Increase the timeout before soft reset to ensure the DMCUB has quiesced.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
If max_downscale_src_width check fails, we exit early from TAP calculation and left a NULL
value to the scaling data structure to cause the zero divide in the DML validation.
[HOW]
Call set default TAP calculation before early exit in get_optimal_number_of_taps due to
max downscale limit exceed.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Signed-off-by: Yihan Zhu <Yihan.Zhu@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Previously the 128b/132b LTTPR support DPCD field was used to decide if
FIXED_VS training sequence required a rate toggle before initiating LT.
When running DP2.1 4.9.x.x compliance tests, emulated LTTPRs can report
no-128b/132b support which is then forwarded by the FIXED_VS retimer.
As a result this test exposes the rate toggle again, erroneously causing
failures as certain compliance sinks don't expect this behaviour.
[HOW]
Add new DPCD register defines/reads to read LTTPR IEEE OUI and device ID.
Decide whether to perform the rate toggle based on the LTTPR's IEEE OUI
which guarantees that we only perform the toggle on affected retimers.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
failed due to cmdtable not created.
switch atombios cmdtable as default.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With HostVM enabled, DCN31 fails to pass validation for 3x4k60. Some Linux
userspace does not downgrade one of the monitors to 4k30, and the result
is that the monitor does not light up. Disable it until the bandwidth
calculation failure is resolved.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We must implement an ACPI re-timer programming interface and notify
ACPI driver whenever a PHY transition is about to take place.
Because some trace lengths on certain platforms are very long,
then a re-timer may need to be programmed whenever a PHY transition
takes place. The implementation of this re-timer programming interface
will notify ACPI driver that PHY transition is taking place and it
will trigger the re-timer as needed.
First we need to gather retimer information from ACPI interface.
Then, in the PRE case, the re-timer interface needs to be called before we call
transmitter ENABLE.
In the POST case, it has to be called after we call transmitter DISABLE.
[How]
Implemented ACPI retimer programming interface.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Rafal Ostrowski <rostrows@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Refactor existing code related to DCN4x for better code sharing with
other modules.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Swapnil Patel <Swapnil.Patel@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
some board designs have eDP0 connected to DP1, need a way to enable
support_edp0_on_dp1 flag, otherwise edp related features cannot work
[how]
do a dmi check during dm initialization to identify systems that
require support_edp0_on_dp1. Optimize quirk table with callback
functions to set quirk entries, retrieve_dmi_info can set quirks
according to quirk entries
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Yilin Chen <Yilin.Chen@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
replace dio encoder access to work with new dio encoder
assignment.
[HOW}
1. before validation, access dio encoder by get_temp_dio_link_enc()
2. after validation, access dio encoder through pipe_ctx->link_res
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In order to avoid component conflicts, spl namespace is needed.
[How]
Adding SPL namespace to the public API os that each user of SPL can have
their own namespace.
Signed-off-by: Navid Assadian <Navid.Assadian@amd.com>
Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some of unit tests use large scaling ratio such that when we
calculate optimal number of taps, max_taps is negative.
Then in recent change, we changed max_taps to uint instead
of int so now max_taps wraps and is positive. This change
changed the behaviour from returning back false to return
true and breaks unit test check
[How]
Add check to prevent max_taps from wrapping and set to 0
instead
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
IDENTITY_RATIO check uses 2 bits for integer, which only allows
checking downscale ratios up to 3. But we support up to 6x
downscale
[How]
Update IDENTITY_RATIO to check 3 bits for integer
Add ASSERT to catch if we downscale more than 6x
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The mismatch type comparison/assignment may cause data loss. Since the
values are always non-negative, it is safe to use unsigned variables to
resolve the mismatch.
Signed-off-by: Navid Assadian <navid.assadian@amd.com>
Reviewed-by: Joshua Aberback <joshua.aberback@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For subsampled YUV output formats, more pixels can get fetched and be
used for scaling.
[How]
Add the adjustment to the calculated recout, so the viewport covers the
corresponding pixels on the source plane.
Signed-off-by: Navid Assadian <Navid.Assadian@amd.com>
Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Passing uint into uchar function param. Pass uint instead
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN36 should inherit the same policy as DCN35 for DML2.
[How]
Add it to the list of checks in translation helper.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Fix the incorrect value of the cursor_buffer_size.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSR-SU may cause some glitching randomly on several panels.
[How]
Temporarily disable the PSR-SU and fallback to PSR1 for
all eDP panels.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3388
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit c31b41f1cb.
We planning to disable the PSR-SU and fallback to PSR1 for
all eDP panels not only for specific eDP panel temporarily.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in max_oustanding_when_urgent_expected,
fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When switching to drm_edid, we slightly changed how to get edid by
removing the possibility of getting them from dc_link when in aux
transaction mode. As MST doesn't initialize the connector with
`drm_connector_init_with_ddc()`, restore the original behavior to avoid
functional changes.
v2:
- Fix build warning of unchecked dereference (kernel test bot)
CC: Alex Hung <alex.hung@amd.com>
CC: Mario Limonciello <mario.limonciello@amd.com>
CC: Roman Li <Roman.Li@amd.com>
CC: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Fixes: 48edb2a425 ("drm/amd/display: switch amdgpu_dm_connector to use struct drm_edid")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove extraneous tab and newline in dml2_core_dcn4.c that was
reported by the bot
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202502211920.txUfwtSj-lkp@intel.com/
Fixes: 70839da636 ("drm/amd/display: Add new DCN401 sources")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the *handle to amdgpu_ip_block ptr for all
functions pointers of is_idle.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://lore.kernel.org/r/20241216-sysfs-const-bin_attr-drm-v1-5-210f2b36b9bf@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce the DCC and Tiling reset callback to all DCE versions that can
call it.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Summary:
* Add support for disconnected eDP streams
* Add log for MALL entry on DCN32x
* Add DCC/Tiling reset helper for DCN and DCE
* Guard against setting dispclk low when active
* Other minor fixes
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
eDP may not be connected to the GPU on driver start causing
fail enumeration.
[How]
Move the virtual signal type check before the eDP connector
signal check.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Harry VanZyllDeJong <hvanzyll@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In current HPO DP2 implementation, driver would enable/disable DIG
encoder when configuring HPO DP2. Therefore, usb4 dp tunnelling should
not use the DIG encoder if the corresponded phy is used by a HPO DP2
stream.
[HOW]
A DP2 stream is treated as a dig stream.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should never apply a minimum dispclk value while in prepare_bandwidth
or while displays are active. This is always an optimization for when
all displays are disabled.
[How]
Defer dispclk optimization until safe_to_lower = true and display_count
reaches 0.
Since 0 has a special value in this logic (ie. no dispclk required)
we also need adjust the logic that clamps it for the actual request
to PMFW.
Reviewed-by: Gabe Teeger <gabe.teeger@amd.com>
Reviewed-by: Leo Chen <leo.chen@amd.com>
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
BT2020 YCbCr input is not handled properly when full range
quantization is used and limited range is not supported at all.
[How]
- Add enums for BT2020 YCbCr limited/full range
- Add limited range CSC matrix
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Robert Mader <robert.mader@collabora.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Add a dyndbg log entry to check whether the driver requested scanout
from MALL cache to PMFW via DMCUB
Reviewed-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The informative structure needs to be extended by the total number of DPPs
required per each active plane.
The new informative field is going to be used as a statistical indicator.
[How]
The dml2_core_calcs_get_informative() routine must count a total number of DPPs.
Reviewed-by: Austin Zheng <austin.zheng@amd.com>
Signed-off-by: Oleh Kuzhylnyi <okuzhyln@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The latest DP spec requires the DP TX to read DPCD F0000h through F0009h
when detecting LTTPR capabilities for the first time.
[How]
Update LTTPR cap retrieval to read up to F0009h (two more bytes than the
previous F0007h), and store the LTTPR ALPM capabilities.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Add a message so users know the stream will be used for seamless boot.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Introduce the DCC and Tiling reset callback to all DCN versions that can
call it.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rename dc_plane_force_update_for_panic to
dc_plane_force_dcc_and_tiling_disable to describe the function operation
in the name. Also, this function might be used in other contexts, and a
more generic name can be helpful for this purpose.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit introduces a function helper for resetting DCN/DCE DCC and
tiling. Those functions are generic for their respective DCN/DCE, so
they were added to the oldest version of each architecture.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 13437c9160.
Reason to revert: idle power regression found in testing.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Leo Zeng <Leo.Zeng@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't try to operate on a drm_wb_connector as an amdgpu_dm_connector.
While dereferencing aconnector->base will "work" it's wrong and
might lead to unknown bad things. Just... don't.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
By default, DCN HW is in idle optimized state which does not allow access
to PHY registers. If BIOS powers up the DCN, it is fine because they will
power up everything. Only exit idle optimized state when not taking control
from VBIOS.
Fixes: be704e5ef4 ("Revert "drm/amd/display: Exit idle optimizations before attempt to access PHY"")
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu can handle async flips on overlay planes, so allow it for atomic
async checks.
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250127-tonyk-async_flip-v12-2-0f7f8a8610d3@igalia.com
[DB: fixed checkpatch warning by adding braces]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
[Why & How]
Remove unused filters and functions
Add static to limit scope
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allow reuse of code by making dcn401_program_pipe()
non static.
Fixes: 2739bd1237 ("drm/amd/display: Allow reuse of of DCN4x code")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Karthi Kandasamy <karthi.kandasamy@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
currently dml2 is using a hard coded 16 to convert memclk to dram_speed_mts.
for apu, this depends on wck_ratio.
change to pass the already calculated dram_speed_mts from fpu to dml2.
v2: use existing calculation of dram_speed_mts for now to avoid regression
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There have been instances of some monitors being unable to link train on
their reported link speed using their selected FFE preset. If a different
FFE preset is found that has a higher rate of success during link training
this workaround can be used to force its FFE preset.
[How]
A new link workaround flag is made called force_dp_ffe_preset. The flag is
checked in override_training_settings and will set lt_settings->ffe_preset
which is null if the flag is not set. The flag is then set in
override_lane_settings.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Brendan Tam <Brendan.Tam@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Instead of converting tables from s1_10 to s1_12, add s1_12 tables instead.
Remove init calls that do the conversion. Add APIs to read s1_10 tables
Reviewed-by: Navid Assadian <navid.assadian@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why&how]
causing some regression on dgpu which still needs the
pre-emptive return, limit this to reporter asic version
it is simple to include
different dcn versions from this point forward, each dcn
resource is initialized with the flag and can be enabled
at will
Reviewed-by: Chris Park <chris.park@amd.com>
Signed-off-by: Ausef Yousof <Ausef.Yousof@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
needed in certain scenarios for debugging and logging
Reviewed-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Martin Leung <martin.leung@amd.com>
Signed-off-by: Leo Zeng <Leo.Zeng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
LLS policy not affected by TF.
Remove check in don't care case and use
pixel format only.
Reviewed-by: Navid Assadian <navid.assadian@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Instead of converting tables from s1_10 to s1_12,
added s1_12 tables instead in SPL
Remove init calls that do the conversion
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For various fixes to mcache_row_bytes calculation.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Setting link DPMS off in response to HPD disconnect creates AUX
transactions on a link that is supposed to be disconnected. This can
cause issues in some cases when the sink re-asserts HPD and expects
source to re-enable the link.
[How]
Avoid AUX transactions on disconnected link.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MAX_SURFACES and MAX_PLANES now have docstrings that better show the difference between the two.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
For enabling 4-plane MPO, we need dc to expose 4 planes for DCN35 and
beyond, as well as DCN21
[how]
Set dc_caps.max_slave_*planes to 3 for appropriate ASICs
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add DM handling for DCN36.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add DCN36 support in dc_resource.c.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Martin Leung <martin.leung@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add case in hdcp_create_workqueue() to support HDCP on DCN36 as well.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add case on clean_up_dsc_blocks() to support DCN36 as well.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Martin Leung <martin.leung@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
