timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull char / misc / IIO driver updates from Greg KH:
"Here is the big set of char, misc, iio, and other smaller driver
subsystems for 6.15-rc1. Lots of stuff in here, including:
- loads of IIO changes and driver updates
- counter driver updates
- w1 driver updates
- faux conversions for some drivers that were abusing the platform
bus interface
- coresight driver updates
- rust miscdevice binding updates based on real-world-use
- other minor driver updates
All of these have been in linux-next with no reported issues for quite
a while"
* tag 'char-misc-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
samples: rust_misc_device: fix markup in top-level docs
Coresight: Fix a NULL vs IS_ERR() bug in probe
misc: lis3lv02d: convert to use faux_device
tlclk: convert to use faux_device
regulator: dummy: convert to use the faux device interface
bus: mhi: host: Fix race between unprepare and queue_buf
coresight: configfs: Constify struct config_item_type
doc: iio: ad7380: describe offload support
iio: ad7380: add support for SPI offload
iio: light: Add check for array bounds in veml6075_read_int_time_ms
iio: adc: ti-ads7924 Drop unnecessary function parameters
staging: iio: ad9834: Use devm_regulator_get_enable()
staging: iio: ad9832: Use devm_regulator_get_enable()
iio: gyro: bmg160_spi: add of_match_table
dt-bindings: iio: adc: Add i.MX94 and i.MX95 support
iio: adc: ad7768-1: remove unnecessary locking
Documentation: ABI: add wideband filter type to sysfs-bus-iio
iio: adc: ad7768-1: set MOSI idle state to prevent accidental reset
iio: adc: ad7768-1: Fix conversion result sign
iio: adc: ad7124: Benefit of dev = indio_dev->dev.parent in ad7124_parse_channel_config()
...
Pull pin control updates from Linus Walleij:
"Core changes:
- None really.
New drivers:
- AMD ISP411 "AMD ISP" driver
- Exynos 2200 and 7870 SoC subdrivers
- Sophgo RISC-V SG2042 and SG2044 subdrivers
- Amlogic A4 subdriver
- Rockchip RK3528 subdriver
- Broadcom BCM21664 subdriver
- Allwinner A523/T527 subdriver
- Ingenic X1600 subdriver
- Microchip SAMA7D65 subdriver, essentially a re-branded Atmel AT91
PIO4 driver, but nowadays a Microschip SoC line
Improvements:
- Bring in the devm_kmemdup_array() helper and use it throughout,
also bring in changes to other subsystems for this to establish
this helper
- Support EGPIO on the Qualcomm SA8775P SoC
- Extend EINT support in the Mediatek driver"
* tag 'pinctrl-v6.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (101 commits)
pinctrl: mediatek: Add EINT support for multiple addresses
pinctrl: amlogic-a4: Drop surplus semicolon
pinctrl: nuvoton: Reduce use of OF-specific APIs
pinctrl: nuvoton: Convert to use struct group_desc
pinctrl: nuvoton: Make use of struct pinfunction and PINCTRL_PINFUNCTION()
pinctrl: nuvoton: Convert to use struct pingroup and PINCTRL_PINGROUP()
pinctrl: npcm8xx: Fix incorrect struct npcm8xx_pincfg assignment
pinctrl: tegra: Fix off by one in tegra_pinctrl_get_group()
pinctrl: PINCTRL_AMDISP should depend on DRM_AMD_ISP
pinctrl: qcom: sa8775p: Enable egpio function
dt-bindings: pinctrl: qcom: Add egpio function for sa8775p
pinctrl: qcom: tlmm-test: Validate irq_enable delivers edge irqs
pinctrl: qcom: Clear latched interrupt status when changing IRQ type
dt-bindings: pinctrl: airoha: Add missing gpio-ranges property
pinctrl: bcm281xx: Add missing assignment in bcm21664_pinctrl_lock_all()
pinctrl: amd: isp411: Fix IS_ERR() vs NULL check in probe()
dt-bindings: pinctrl: at91-pio4: add microchip,sama7d65-pinctrl
pinctrl: tegra: Set SFIO mode to Mux Register
pinctrl-tegra: Restore SFSEL bit when freeing pins
pinctrl: tegra: Add descriptions for SoC data fields
...
Pull regulator updates from Mark Brown:
"This has been a very quiet release, we've got support for one device
added, another removed, and some smaller fixes and API improvements.
The main thing of note is the rework of the PCA9450 LDO5 handling.
- A rework of the handling of LDO5 on the PCA9450, this was quite
wrong in how it handled the SD_VSEL conrol and only worked for some
system designs. This includes a DTS update since there was a not
quite ABI compatible change as part of the fix
- A devres change introducing devm_kmemdup_array() was pulled in so
it could be used with some regulator conversions to that function,
this pulled in some other devres and IIO stuff that was part of the
same pull request
- Removal of the PCF50633 driver, the SoC for the OpenMoko platform
that used it has been removed
- Support for the NXP PF9453"
* tag 'regulator-v6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (24 commits)
regulator: axp20x: AXP717: dcdc4 doesn't have delay
regulator: dt-bindings: rtq2208: Cleanup whitespace
regulator: dt-bindings: rtq2208: Mark fixed LDO VOUT property as deprecated
regulator: rtq6752: make const read-only array fault_mask static
regulator: pf9453: add PMIC PF9453 support
regulator: dt-bindings: pca9450: Add nxp,pf9453 compatible string
regulator: pcf50633-regulator: Remove
regulator: pca9450: Handle hardware with fixed SD_VSEL for LDO5
regulator: cros-ec: use devm_kmemdup_array()
regulator: devres: use devm_kmemdup_array()
regulator: Add (devm_)of_regulator_get()
devres: Introduce devm_kmemdup_array()
iio: imu: st_lsm9ds0: Replace device.h with what is needed
driver core: Split devres APIs to device/devres.h
err.h: move IOMEM_ERR_PTR() to err.h
regulator: pca9450: Remove duplicate code in probe
regulator: ad5398: Fix incorrect power down bit mask
regulator: pca9450: Fix enable register for LDO5
regulator: pca9450: Fix control register for LDO5
Revert "regulator: pca9450: Add SD_VSEL GPIO for LDO5"
...
Pull timer cleanups from Thomas Gleixner:
"A treewide hrtimer timer cleanup
hrtimers are initialized with hrtimer_init() and a subsequent store to
the callback pointer. This turned out to be suboptimal for the
upcoming Rust integration and is obviously a silly implementation to
begin with.
This cleanup replaces the hrtimer_init(T); T->function = cb; sequence
with hrtimer_setup(T, cb);
The conversion was done with Coccinelle and a few manual fixups.
Once the conversion has completely landed in mainline, hrtimer_init()
will be removed and the hrtimer::function becomes a private member"
* tag 'timers-cleanups-2025-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (100 commits)
wifi: rt2x00: Switch to use hrtimer_update_function()
io_uring: Use helper function hrtimer_update_function()
serial: xilinx_uartps: Use helper function hrtimer_update_function()
ASoC: fsl: imx-pcm-fiq: Switch to use hrtimer_setup()
RDMA: Switch to use hrtimer_setup()
virtio: mem: Switch to use hrtimer_setup()
drm/vmwgfx: Switch to use hrtimer_setup()
drm/xe/oa: Switch to use hrtimer_setup()
drm/vkms: Switch to use hrtimer_setup()
drm/msm: Switch to use hrtimer_setup()
drm/i915/request: Switch to use hrtimer_setup()
drm/i915/uncore: Switch to use hrtimer_setup()
drm/i915/pmu: Switch to use hrtimer_setup()
drm/i915/perf: Switch to use hrtimer_setup()
drm/i915/gvt: Switch to use hrtimer_setup()
drm/i915/huc: Switch to use hrtimer_setup()
drm/amdgpu: Switch to use hrtimer_setup()
stm class: heartbeat: Switch to use hrtimer_setup()
i2c: Switch to use hrtimer_setup()
iio: Switch to use hrtimer_setup()
...
Jonathan writes:
IIO: New device support, features and cleanup for the 6.15 cycle.
The usual mixture of new drivers, support in existing drivers for new
devices, a range of features and general subsystem cleanup.
Two merges of immutable branches in here:
* SPI offload support. Culmination of a long effort to bring the ability
to offload triggered sequences of SPI operations to specific hardware,
allow high datarate acquisition over an SPI bus (if you have the right
hardware / FPGA firmware)
* GPIO set-array-helper - enables code simplification.
New device support
==================
adi,ad3552r-hs:
- Add support for AD3541r and AD3542r via newly supported FPGA HDL.
adi,ad4030
- New driver supporting the AD4030, AD4630 AD4630-16, AD4640-24, AD4632-16,
AD4632-24 1 and 2 channel high precision SPI ADCs.
adi,ad4851
- New driver and backend support for the AD4851, AD4852, AD4853, AD4854,
AD4855, AD4846, AD4857, AD4858 and AD4858I high speed multichannel
simultaneous sampling ADCs.
adi,ad7191
- New driver for this 24-bit ADC for precision bridge applications,
adi,ad7380
- Add support for the adaq4381-4 which is a 14-bit version of the
already supported adaq4380-1
adi,adis16550
- New driver using the ADIS library (which needed extensions) for this
IMU.
brcm,apds9160
- New driver for this proximity and ambient light sensor.
dynaimage,al3000a
- New driver for this illuminance sensor.
mcube,mc3230
- Add support for the mc3510c accelerometer with a different scale to existing
supported parts (some rework preceded this)
nxp,imx93
- Add compatibles for imx94 and imx95 which are fully compatible with imx93.
rockchip,saradc
- Add support for the RK3528 ADC
- Add support for the RK3562 ADC
silab,si7210
- New driver to support this I2C Hall effect magnetic position sensor.
ti,ads7138
- New driver supporting the ADS7128 and AD7138 I2C ADCs.
Staging driver drop
===================
adi,adis16240
- Drop this impact sensor. Interesting part but complex hence never left
staging due to ABI challenges. No longer readily available so drop driver.
New features
============
Documentation
- A really nice overview document introduce ADC terminology and how
it maps to IIO.
core
- New description for FAULT events, used in the ad7173.
- filter_type ABI used in ad4130.
buffer-dmaengine
- Split DMA channel request from buffer allocation (for SPI offload)
- Add a new _with_handle setup variant. (for SPI offload)
adi,adf4371
- Add control of reference clock type and support for frequency doubling
where appropriate.
adi,ad4695
- Support SPI offload.
- Support oversampling control.
adi,ad5791
- Support SPI offload.
adi,ad7124
- Add channel calibration support.
adi,ad7380:
- Alert support (threshold interrupts)
- SPI offload support.
adi,ad7606
- Support writing registers when using backend enabling software control
of modes.
adi,ad7944
- Support SPI offload.
adi,ad9832
- Use devm_regulator_get_enable() to simplify code.
adi,ad9834
- Use devm_regulator_get_enable() to simplify code.
adi,adxl345
- Improve IRQ handling code.
- Add debug access to registers.
bosch,bmi270
- Add temperature channel support.
- Add data ready trigger.
google,cross_ec
- Add trace events.
mcube,mc3230
- Add mount matrix support
- Add an OF match table.
Cleanup and minor bug fixes
===========================
Tree wide:
- Stop using iio_device_claim_direct_scoped() and introduce sparse friendly
iio_device_claim/release_direct()
The conditional scoped cleanup has proved hard to deal with, requiring
workarounds for various compiler issues and in is rather non-intuitive
so abandon that experiment. One of the attractions of that approach was
that it made it much harder to have unbalanced claim/release bugs so
instead introduce a conditional-lock style boolean returning new pair
of functions. These are inline in the header and have __acquire and
__release calls allowing sparse to detect lack of balance. There are
occasional false positives but so far those have reflected complex code
paths that benefited from cleanup anyway.
The first set of driver conversions are in this pull request, more to
follow next cycle. Various related cleanup in drivers.
Removal of the _scoped code is completed and the definition removed.
- Use of str_enable_disable() and similar helpers.
- Don't set regmap cache to REGCACHE_NONE as that's the default anyway.
- Change some caches from RBTREE to MAPLE reflecting best practice.
- Use the new gpiod_multi_set_value_cansleep()
- Make sure to grab direct mode for some calibrations paths.
- Avoid using memcmp on structures when checking for matching channel configs.
Instead just match field by field.
dt-bindings:
- Fix up indentation inconsistencies.
gts-helper:
- Simplify building of available scale table.
adi,ad-sigma-delta
- Make sure to disable channel after calibration done.
- Add error handling in configuring channel during calibration.
adi,ad2s1201
- use a bitmap_write() rather than directly accessing underlying storage.
adi,ad3552r-hs
- Fix a wrong error message.
- Make sure to use instruction mode for configuration.
adi,ad4695
- Add a conversion to ensure exit from conversion mode.
- Use custom regmap to handle required sclk rate change.
- Fix an out of bounds array access
- Simplify oversampling ratio handling.
adi,ad4851
- Fix a sign bug.
adi,ad5791
- Fix wrong exported number of storage bits.
adi,ad7124
- Disable all channels at probe to avoid strange initial configurations.
adi,ad7173
- Rework to allow static const struct ad_sigma_delta without need
to make a copy.
adi,ad7623
- Drop a BSD license tag that the authors consider unnecessary.
adi,ad7768-1
- Fix channels sign description exposed to user space.
- Set MOSI idle state to avoid accidental device reset.
- Avoid some overkill locking.
adi,axi-dac
- Check if device interface is busy when enabling data stream.
- Add control of bus mode.
bosch,bmi270
- Move a struct definition to a c file as only used there.
vishay,veml6030
- Enable regmap cache to reduce bus traffic.
- Fix ABI bug around scale reporting.
vishay,vem6075
- Check array bounds to harden against broken hardware.
Various other minor tweaks and fixes not called out.
*
* tag 'iio-for-6.15a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (223 commits)
doc: iio: ad7380: describe offload support
iio: ad7380: add support for SPI offload
iio: light: Add check for array bounds in veml6075_read_int_time_ms
iio: adc: ti-ads7924 Drop unnecessary function parameters
staging: iio: ad9834: Use devm_regulator_get_enable()
staging: iio: ad9832: Use devm_regulator_get_enable()
iio: gyro: bmg160_spi: add of_match_table
dt-bindings: iio: adc: Add i.MX94 and i.MX95 support
iio: adc: ad7768-1: remove unnecessary locking
Documentation: ABI: add wideband filter type to sysfs-bus-iio
iio: adc: ad7768-1: set MOSI idle state to prevent accidental reset
iio: adc: ad7768-1: Fix conversion result sign
iio: adc: ad7124: Benefit of dev = indio_dev->dev.parent in ad7124_parse_channel_config()
iio: adc: ad7124: Implement system calibration
iio: adc: ad7124: Implement internal calibration at probe time
iio: adc: ad_sigma_delta: Add error checking for ad_sigma_delta_set_channel()
iio: adc: ad4130: Adapt internal names to match official filter_type ABI
iio: adc: ad7173: Fix comparison of channel configs
iio: adc: ad7124: Fix comparison of channel configs
iio: adc: ad4130: Fix comparison of channel setups
...
The array contains only 5 elements, but the index calculated by
veml6075_read_int_time_index can range from 0 to 7,
which could lead to out-of-bounds access. The check prevents this issue.
Coverity Issue
CID 1574309: (#1 of 1): Out-of-bounds read (OVERRUN)
overrun-local: Overrunning array veml6075_it_ms of 5 4-byte
elements at element index 7 (byte offset 31) using
index int_index (which evaluates to 7)
This is hardening against potentially broken hardware. Good to have
but not necessary to backport.
Fixes: 3b82f43238 ("iio: light: add VEML6075 UVA and UVB light sensor driver")
Signed-off-by: Karan Sanghavi <karansanghvi98@gmail.com>
Reviewed-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/Z7dnrEpKQdRZ2qFU@Emma
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Device pointer is the only variable which is used by the
ads7924_get_channels_config() and which is declared outside this
function. Still, the function gets the iio_device and i2c_client as
parameters. The sole caller of this function (probe) already has the
device pointer which it can directly pass to the function.
Simplify code by passing the device pointer directly as a parameter
instead of digging it from the iio_device's private data.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/2bb4c61122eca2f3a35f6087e7d9815675013f66.1740993491.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Checking the binary representation of two structs (of the same type)
for equality doesn't have the same semantic as comparing all members for
equality. The former might find a difference where the latter doesn't in
the presence of padding or when ambiguous types like float or bool are
involved. (Floats typically have different representations for single
values, like -0.0 vs +0.0, or 0.5 * 2² vs 0.25 * 2³. The type bool has
at least 8 bits and the raw values 1 and 2 (probably) both evaluate to
true, but memcmp finds a difference.)
When searching for a channel that already has the configuration we need,
the comparison by member is the one that is needed.
Convert the comparison accordingly to compare the members one after
another. Also add a static_assert guard to (somewhat) ensure that when
struct ad7173_channel_config::config_props is expanded, the comparison
is adapted, too.
This issue is somewhat theoretic, but using memcmp() on a struct is a
bad pattern that is worth fixing.
Fixes: 76a1e6a428 ("iio: adc: ad7173: add AD7173 driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-14-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Checking the binary representation of two structs (of the same type)
for equality doesn't have the same semantic as comparing all members for
equality. The former might find a difference where the latter doesn't in
the presence of padding or when ambiguous types like float or bool are
involved. (Floats typically have different representations for single
values, like -0.0 vs +0.0, or 0.5 * 2² vs 0.25 * 2³. The type bool has
at least 8 bits and the raw values 1 and 2 (probably) both evaluate to
true, but memcmp finds a difference.)
When searching for a channel that already has the configuration we need,
the comparison by member is the one that is needed.
Convert the comparison accordingly to compare the members one after
another. Also add a static_assert guard to (somewhat) ensure that when
struct ad7124_channel_config::config_props is expanded, the comparison
is adapted, too.
This issue is somewhat theoretic, but using memcmp() on a struct is a
bad pattern that is worth fixing.
Fixes: 7b8d045e49 ("iio: adc: ad7124: allow more than 8 channels")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-13-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Checking the binary representation of two structs (of the same type)
for equality doesn't have the same semantic as comparing all members for
equality. The former might find a difference where the latter doesn't in
the presence of padding or when ambiguous types like float or bool are
involved. (Floats typically have different representations for single
values, like -0.0 vs +0.0, or 0.5 * 2² vs 0.25 * 2³. The type bool has
at least 8 bits and the raw values 1 and 2 (probably) both evaluate to
true, but memcmp finds a difference.)
When searching for a channel that already has the configuration we need,
the comparison by member is the one that is needed.
Convert the comparison accordingly to compare the members one after
another. Also add a static_assert guard to (somewhat) ensure that when
struct ad4130_setup_info is expanded, the comparison is adapted, too.
This issue is somewhat theoretic, but using memcmp() on a struct is a
bad pattern that is worth fixing.
Fixes: 62094060cf ("iio: adc: ad4130: add AD4130 driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-12-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The function ad_sd_calibrate() enables the channel to calibrate at
function entry but doesn't disable it on exit. This is problematic
because if two (or more) channels are calibrated in a row, the second
calibration isn't executed as intended as the first (still enabled)
channel is recalibrated and after the first irq (i.e. when the
calibration of the first channel completed) the calibration is aborted.
This currently affects ad7173 only, as the other drivers using
ad_sd_calibrate() never have more than one channel enabled at a time.
To fix this, disable the calibrated channel after calibration.
Fixes: 031bdc8aee ("iio: adc: ad7173: add calibration support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-11-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Successive Approximation ADC (SARADC) in RK3528 uses the v2
controller and support:
- 10-bit resolution
- Up to 1MS/s sampling rate
- 4 single-ended input channels
- Current consumption: 0.5mA @ 1MS/s
Add support for the 4 channels of 10-bit resolution supported by SARADC
in RK3528.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20250227184058.2964204-3-jonas@kwiboo.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reorganize the IRQ handler. Move the overrun handling to the bottom.
Overrun leads to reset the interrupt register. This also happens at
evaluation of a particular interrupt event. First evaluate an event
if possible, then fall back to overrun handling. Additionally simplify
fetching the interrupt status function.
Both is in preparation to build interrupt handling up for the handling
of different detected events, implemented in follow up patches.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250220104234.40958-4-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix some out of bounds array access of st->channels_cfg in the ad4695
driver. This array only has elements for voltage channels, but it was
also being accessed for the temperature channel in a few cases causing
reading past the end of the array.
In some cases, this was harmless because the value was read but not
used. However, the in_temp_sampling_frequency attribute shares code
with the in_voltageY_sampling_frequency attributes and was trying to
read the oversampling ratio from the st->channels_cfg array. This
resulted in a garbage value being used in the calculation and the
resulting in_temp_sampling_frequency value was incorrect.
To fix, make sure we always check that we are dealing with a voltage
channel before accessing the st->channels_cfg array and use an
oversampling ratio of 1 for the temperature channel (multiplicative
identity value) since that channel doesn't support oversampling.
Fixes: 67d63185db ("iio: adc: ad4695: add offload-based oversampling support")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Trevor Gamblin <tgamblin@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250218-iio-adc-ad4695-fix-out-of-bounds-array-access-v1-1-57fef8c7a3fd@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
