The newly added driver only builds when DRM_DISPLAY_DP_HELPER is enabled:
x86_64-linux-ld: drivers/gpu/drm/panel/panel-visionox-r66451.o: in function `visionox_r66451_enable':
panel-visionox-r66451.c:(.text+0x105): undefined reference to `drm_dsc_pps_payload_pack'
Select both CONFIG_DRM_DISPLAY_DP_HELPER and CONFIG_DRM_DISPLAY_HELPER to
ensure the helper function is always available.
Fixes: a6dfab2738 ("drm/panel: Add driver for Visionox r66451 panel")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230719130940.659837-1-arnd@kernel.org
When building with W=1, the following warning occurs.
drivers/gpu/drm/bridge/analogix/analogix-anx78xx.c:48:17: warning: ‘anx781x_i2c_addresses’ defined but not used [-Wunused-const-variable=] static const u8 anx781x_i2c_addresses[] = {
^~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/bridge/analogix/analogix-anx78xx.c:40:17: warning: ‘anx7808_i2c_addresses’ defined but not used [-Wunused-const-variable=] static const u8 anx7808_i2c_addresses[] = {
When CONFIG_IO is disabled, above two variables are not used,
since the place where it is used is inclueded in the macro
CONFIG_OF.
Even for drivers that do not depend on CONFIG_OF, it's almost
always better to leave out the of_match_ptr(), since the only
thing it can possibly do is to save a few bytes of .text if a
driver can be used both with and without it. Hence we remove
all of_match_ptr() used in other places.
Fixes: 0647e7dd3f ("drm/bridge: Add Analogix anx78xx support")
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230731021345.219588-1-wangzhu9@huawei.com
Currently we use the drm_dp_dpcd_read_caps() helper in the DRM side of
nouveau in order to read the DPCD of a DP connector, which makes sure we do
the right thing and also check for extended DPCD caps. However, it turns
out we're not currently doing this on the nvkm side since we don't have
access to the drm_dp_aux structure there - which means that the DRM side of
the driver and the NVKM side can end up with different DPCD capabilities
for the same connector.
Ideally in order to fix this, we just want to use the
drm_dp_read_dpcd_caps() helper in nouveau. That's not currently possible
though, and is going to depend on having a bunch of the DP code moved out
of nvkm and into the DRM side of things as part of the GSP enablement work.
Until then however, let's workaround this problem by porting a copy of
drm_dp_read_dpcd_caps() into NVKM - which should fix this issue.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Link: https://gitlab.freedesktop.org/drm/nouveau/-/issues/211
Link: https://patchwork.freedesktop.org/patch/msgid/20230728225858.350581-1-lyude@redhat.com
Aspeed always report the display port as "connected", because it
doesn't set a .detect_ctx callback.
Fix this by providing the proper detect callback for astdp and dp501.
This also fixes the following regression:
Since commit fae7d18640 ("drm/probe-helper: Default to 640x480 if no
EDID on DP") The default resolution is now 640x480 when no monitor is
connected. But Aspeed graphics is mostly used in servers, where no monitor
is attached. This also affects the remote BMC resolution to 640x480, which
is inconvenient, and breaks the anaconda installer.
v2: Add .detect callback to the dp/dp501 connector (Jani Nikula)
v3: Use .detect_ctx callback, and refactors (Thomas Zimmermann)
Add a BMC virtual connector
v4: Better indent detect_ctx() functions (Thomas Zimmermann)
v5: Enable polling of the dp and dp501 connector status
(Thomas Zimmermann)
v6: Change check order in ast_astdp_is_connected (Jammy Huang)
Fixes: fae7d18640 ("drm/probe-helper: Default to 640x480 if no EDID on DP")
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713134316.332502-2-jfalempe@redhat.com
Most aspeed devices have a BMC, which allows to remotely see the screen.
Also in the common use case, those servers don't have a display connected.
So add a Virtual connector, to reflect that even if no display is
connected, the framebuffer can still be seen remotely.
This prepares the work to implement a detect_ctx() for the Display port
connector.
v4: call drm_add_modes_noedid() with 4096x4096 (Thomas Zimmermann)
remove useless struct field init to 0 (Thomas Zimmermann)
don't use drm_simple_encoder_init() (Thomas Zimmermann)
inline ast_bmc_connector_init() (Thomas Zimmermann)
Fixes: fae7d18640 ("drm/probe-helper: Default to 640x480 if no EDID on DP")
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713134316.332502-1-jfalempe@redhat.com
Currently, it is possible for the composer to be set as enabled and then
as disabled without a proper call for the vkms_vblank_simulate(). This
is problematic, because the driver would skip one CRC output, causing CRC
tests to fail. Therefore, we need to make sure that, for each time the
composer is set as enabled, a composer job is added to the queue.
In order to provide this guarantee, add a mutex that will lock before
the composer is set as enabled and will unlock only after the composer
job is added to the queue. This way, we can have a guarantee that the
driver won't skip a CRC entry.
This race-condition is affecting the IGT test "writeback-check-output",
making the test fail and also, leaking writeback framebuffers, as the
writeback job is queued, but it is not signaled. This patch avoids both
problems.
[v2]:
* Create a new mutex and keep the spinlock across the atomic commit in
order to avoid interrupts that could result in deadlocks.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Arthur Grillo <arthurgrillo@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230523123207.173976-1-mcanal@igalia.com
Support a 1D gamma LUT with interpolation for each color channel on the
VKMS driver. Add a check for the LUT length by creating
vkms_atomic_check().
Enable VKMS to run the test igt@kms_plane@pixel-format.
Tested with:
igt@kms_color@gamma
igt@kms_color@legacy-gamma
igt@kms_color@invalid-gamma-lut-sizes
v2:
- Add interpolation between the values of the LUT (Simon Ser)
v3:
- s/ratio/delta (Pekka)
- s/color_channel/channel_value (Pekka)
- s/lut_area/lut_channel
- Store the `drm_color_lut`, `lut_length`, and
`channel_value2index_ratio` inside a struct called `vkms_lut`
(Pekka)
- Pre-compute some constants values used through the LUT procedure
(Pekka)
- Change the switch statement to a cast to __u16* (Pekka)
- Make the apply_lut_to_channel_value return the computation result
(Pekka)
v4:
- Add a comment explaining that `enum lut_area` depends on the
layout of `struct drm_color_lut` (Pekka)
- Remove unused variable (kernel test robot)
v5:
- Mention that this will make it possible to run the test
igt@kms_plane@pixel-format (Maíra)
- s/had/has (Maíra)
Signed-off-by: Arthur Grillo <arthurgrillo@riseup.net>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230709013835.161004-1-arthurgrillo@riseup.net
Currently, engine drivers only enable runtime PM during the host1x
init callback. This can happen slightly later than the probe, which
can cause the power domain to intermittently not be turned off after
probe.
My hypothesis is that there is a race condition between the post-probe
power domain poweroff that is done from a queued work, and the
pm_runtime_enable call happening in the host1x init callback.
If the pm_runtime_enable call happens first, everything is OK and
the power off work can disable the power domain as PM runtime is
enabled and the device is runtime suspended. If power off work runs
first, PM runtime is still disabled for the device and the domain
must be kept powered.
Resolve the issue by moving the runtime PM enablement to the
probe function.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230613095215.2497004-1-cyndis@kapsi.fi
If a context device was not attached to IOMMU, we kept the old
success err value causing context devices to be unregistered but
success to be returned. This would mean that things would go on
but with context isolation disabled.
To decide on an explicit behavior, let's return an error code
here instead. If someone wants to go without IOMMU on a platform
modern enough to support context isolation, they can remove the
context devices from device tree.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230413082202.114721-2-cyndis@kapsi.fi
A proposed update to clang's -Wconstant-logical-operand to warn when the
left hand side is a constant shows the following instance in
nsecs_to_jiffies_timeout() when NSEC_PER_SEC is not a multiple of HZ,
such as CONFIG_HZ=300:
drivers/gpu/drm/i915/gem/i915_gem_wait.c:189:24: warning: use of logical '&&' with constant operand [-Wconstant-logical-operand]
189 | if (NSEC_PER_SEC % HZ &&
| ~~~~~~~~~~~~~~~~~ ^
drivers/gpu/drm/i915/gem/i915_gem_wait.c:189:24: note: use '&' for a bitwise operation
189 | if (NSEC_PER_SEC % HZ &&
| ^~
| &
drivers/gpu/drm/i915/gem/i915_gem_wait.c:189:24: note: remove constant to silence this warning
1 warning generated.
Turn this into an explicit comparison against zero to make the
expression a boolean to make it clear this should be a logical check,
not a bitwise one.
Link: https://reviews.llvm.org/D142609
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230718-nsecs_to_jiffies_timeout-constant-logical-operand-v1-2-36ed8fc8faea@kernel.org
A proposed update to clang's -Wconstant-logical-operand to warn when the
left hand side is a constant shows the following instance in
nsecs_to_jiffies_timeout() when NSEC_PER_SEC is not a multiple of HZ,
such as CONFIG_HZ=300:
In file included from drivers/gpu/drm/v3d/v3d_debugfs.c:12:
drivers/gpu/drm/v3d/v3d_drv.h:343:24: warning: use of logical '&&' with constant operand [-Wconstant-logical-operand]
343 | if (NSEC_PER_SEC % HZ &&
| ~~~~~~~~~~~~~~~~~ ^
drivers/gpu/drm/v3d/v3d_drv.h:343:24: note: use '&' for a bitwise operation
343 | if (NSEC_PER_SEC % HZ &&
| ^~
| &
drivers/gpu/drm/v3d/v3d_drv.h:343:24: note: remove constant to silence this warning
1 warning generated.
Turn this into an explicit comparison against zero to make the
expression a boolean to make it clear this should be a logical check,
not a bitwise one.
Link: https://reviews.llvm.org/D142609
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230718-nsecs_to_jiffies_timeout-constant-logical-operand-v1-1-36ed8fc8faea@kernel.org
The commit 45b58669e5 ("drm/ssd130x: Allocate buffer in the plane's
.atomic_check() callback") moved the buffers allocation to be done in
the primary plane's .atomic_check() callback.
But it missed that since the driver uses a shadow-buffered plane, the
__drm_gem_{reset,duplicate,destroy}_shadow_plane() helper functions
must be used in the struct drm_plane_funcs handlers.
This was missed because the mentioned commit did not remove the macro
DRM_GEM_SHADOW_PLANE_FUNCS, which leads to the custom plane's atomic
state management handlers to not be used.
Fixes: 45b58669e5 ("drm/ssd130x: Allocate buffer in the plane's .atomic_check() callback")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Closes: https://lore.kernel.org/dri-devel/20230727122412.2464210-1-arnd@kernel.org
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230727140453.577445-1-javierm@redhat.com
Drivers are not allowed to fail after drm_atomic_helper_swap_state() has
been called and the new atomic state is stored into the current sw state.
Since the struct ssd130x_device .data_array is allocated in the encoder's
.atomic_enable callback, the operation can fail and this is after the new
state has been stored. So it can break an atomic mode settings assumption.
Fix this by having custom helpers to allocate, duplicate and destroy the
plane state, that will take care of allocating and freeing these buffers.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230726105433.389740-2-javierm@redhat.com
