The sparse complaints around the static_asserts were obscuring
more useful complaints. So, don't check the static_asserts,
and fix the remaining sparse complaints.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
chtls_pt_recvmsg() receives a skb with tls header and subsequent
skb with data, need to finalize the data copy whenever next skb
with tls header is available. but here current tls header is
overwritten by next available tls header, ends up corrupting
user buffer data. fixing it by finalizing current record whenever
next skb contains tls header.
v1->v2:
- Improved commit message.
Fixes: 17a7d24aa8 ("crypto: chtls - generic handling of data and hdr")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Link: https://lore.kernel.org/r/20201022190556.21308-1-vinay.yadav@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPA transactions describe actions to be performed by the IPA
hardware. Three cases use IPA transactions: transmitting a socket
buffer; providing a page to receive packet data; and issuing an IPA
immediate command. An IPA transaction contains a scatter/gather
list (SGL) to hold the set of actions to be performed.
We map buffers in the SGL for DMA at the time they are added to the
transaction. For skb TX transactions, we fill the SGL with a call
to skb_to_sgvec(). Page RX transactions involve a single page
pointer, and that is recorded in the SGL with sg_set_page(). In
both of these cases we then map the SGL for DMA with a call to
dma_map_sg().
Immediate commands are different. The payload for an immediate
command comes from a region of coherent DMA memory, which must
*not* be mapped for DMA. For that reason, gsi_trans_cmd_add()
sort of hand-crafts each SGL entry added to a command transaction.
This patch fixes a problem with the code that crafts the SGL entry
for an immediate command. Previously a portion of the SGL entry was
updated using sg_set_buf(). However this is not valid because it
includes a call to virt_to_page() on the buffer, but the command
buffer pointer is not a linear address.
Since we never actually map the SGL for command transactions, there
are very few fields in the SGL we need to fill. Specifically, we
only need to record the DMA address and the length, so they can be
used by __gsi_trans_commit() to fill a TRE. We additionally need to
preserve the SGL flags so for_each_sg() still works. For that we
can simply assign a null page pointer for command SGL entries.
Fixes: 9dd441e4ed ("soc: qcom: ipa: GSI transactions")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201022010029.11877-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-tree/merge window issues:
- rtl8150: don't incorrectly assign random MAC addresses; fix late
in the 5.9 cycle started depending on a return code from
a function which changed with the 5.10 PR from the usb subsystem
Current release - regressions:
- Revert "virtio-net: ethtool configurable RXCSUM", it was causing
crashes at probe when control vq was not negotiated/available
Previous releases - regressions:
- ixgbe: fix probing of multi-port 10 Gigabit Intel NICs with an MDIO
bus, only first device would be probed correctly
- nexthop: Fix performance regression in nexthop deletion by
effectively switching from recently added synchronize_rcu()
to synchronize_rcu_expedited()
- netsec: ignore 'phy-mode' device property on ACPI systems;
the property is not populated correctly by the firmware,
but firmware configures the PHY so just keep boot settings
Previous releases - always broken:
- tcp: fix to update snd_wl1 in bulk receiver fast path, addressing
bulk transfers getting "stuck"
- icmp: randomize the global rate limiter to prevent attackers from
getting useful signal
- r8169: fix operation under forced interrupt threading, make the
driver always use hard irqs, even on RT, given the handler is
light and only wants to schedule napi (and do so through
a _irqoff() variant, preferably)
- bpf: Enforce pointer id generation for all may-be-null register
type to avoid pointers erroneously getting marked as null-checked
- tipc: re-configure queue limit for broadcast link
- net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN
tunnels
- fix various issues in chelsio inline tls driver
Misc:
- bpf: improve just-added bpf_redirect_neigh() helper api to support
supplying nexthop by the caller - in case BPF program has already
done a lookup we can avoid doing another one
- remove unnecessary break statements
- make MCTCP not select IPV6, but rather depend on it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ceke
-----END PGP SIGNATURE-----
Merge tag 'net-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Cross-tree/merge window issues:
- rtl8150: don't incorrectly assign random MAC addresses; fix late in
the 5.9 cycle started depending on a return code from a function
which changed with the 5.10 PR from the usb subsystem
Current release regressions:
- Revert "virtio-net: ethtool configurable RXCSUM", it was causing
crashes at probe when control vq was not negotiated/available
Previous release regressions:
- ixgbe: fix probing of multi-port 10 Gigabit Intel NICs with an MDIO
bus, only first device would be probed correctly
- nexthop: Fix performance regression in nexthop deletion by
effectively switching from recently added synchronize_rcu() to
synchronize_rcu_expedited()
- netsec: ignore 'phy-mode' device property on ACPI systems; the
property is not populated correctly by the firmware, but firmware
configures the PHY so just keep boot settings
Previous releases - always broken:
- tcp: fix to update snd_wl1 in bulk receiver fast path, addressing
bulk transfers getting "stuck"
- icmp: randomize the global rate limiter to prevent attackers from
getting useful signal
- r8169: fix operation under forced interrupt threading, make the
driver always use hard irqs, even on RT, given the handler is light
and only wants to schedule napi (and do so through a _irqoff()
variant, preferably)
- bpf: Enforce pointer id generation for all may-be-null register
type to avoid pointers erroneously getting marked as null-checked
- tipc: re-configure queue limit for broadcast link
- net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN
tunnels
- fix various issues in chelsio inline tls driver
Misc:
- bpf: improve just-added bpf_redirect_neigh() helper api to support
supplying nexthop by the caller - in case BPF program has already
done a lookup we can avoid doing another one
- remove unnecessary break statements
- make MCTCP not select IPV6, but rather depend on it"
* tag 'net-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (62 commits)
tcp: fix to update snd_wl1 in bulk receiver fast path
net: Properly typecast int values to set sk_max_pacing_rate
netfilter: nf_fwd_netdev: clear timestamp in forwarding path
ibmvnic: save changed mac address to adapter->mac_addr
selftests: mptcp: depends on built-in IPv6
Revert "virtio-net: ethtool configurable RXCSUM"
rtnetlink: fix data overflow in rtnl_calcit()
net: ethernet: mtk-star-emac: select REGMAP_MMIO
net: hdlc_raw_eth: Clear the IFF_TX_SKB_SHARING flag after calling ether_setup
net: hdlc: In hdlc_rcv, check to make sure dev is an HDLC device
bpf, libbpf: Guard bpf inline asm from bpf_tail_call_static
bpf, selftests: Extend test_tc_redirect to use modified bpf_redirect_neigh()
bpf: Fix bpf_redirect_neigh helper api to support supplying nexthop
mptcp: depends on IPV6 but not as a module
sfc: move initialisation of efx->filter_sem to efx_init_struct()
mpls: load mpls_gso after mpls_iptunnel
net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN tunnels
net/sched: act_gate: Unlock ->tcfa_lock in tc_setup_flow_action()
net: dsa: bcm_sf2: make const array static, makes object smaller
mptcp: MPTCP_IPV6 should depend on IPV6 instead of selecting it
...
After mac address change request completes successfully, the new mac
address need to be saved to adapter->mac_addr as well as
netdev->dev_addr. Otherwise, adapter->mac_addr still holds old
data.
Fixes: 62740e9788 ("net/ibmvnic: Update MAC address settings after adapter reset")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201020223919.46106-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver depends on mmio regmap API but doesn't select the appropriate
Kconfig option. This fixes it.
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20201020073515.22769-1-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver calls ether_setup to set up the network device.
The ether_setup function would add the IFF_TX_SKB_SHARING flag to the
device. This flag indicates that it is safe to transmit shared skbs to
the device.
However, this is not true. This driver may pad the frame (in eth_tx)
before transmission, so the skb may be modified.
Fixes: 550fd08c2c ("net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared")
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201020063420.187497-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hdlc_rcv function is used as hdlc_packet_type.func to process any
skb received in the kernel with skb->protocol == htons(ETH_P_HDLC).
The purpose of this function is to provide second-stage processing for
skbs not assigned a "real" L3 skb->protocol value in the first stage.
This function assumes the device from which the skb is received is an
HDLC device (a device created by this module). It assumes that
netdev_priv(dev) returns a pointer to "struct hdlc_device".
However, it is possible that some driver in the kernel (not necessarily
in our control) submits a received skb with skb->protocol ==
htons(ETH_P_HDLC), from a non-HDLC device. In this case, the skb would
still be received by hdlc_rcv. This will cause problems.
hdlc_rcv should be able to recognize and drop invalid skbs. It should
first make sure "dev" is actually an HDLC device, before starting its
processing. This patch adds this check to hdlc_rcv.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201020013152.89259-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
efx_probe_filters() has not been called yet when EF100 calls into
efx_mcdi_filter_table_probe(), for which it wants to take the
filter_sem.
Fixes: a9dc3d5612 ("sfc_ef100: RX filter table management and related gubbins")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Link: https://lore.kernel.org/r/24fad43e-887d-051e-25e3-506f23f63abf@solarflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Don't populate the const array rate_table on the stack but instead it
static. Makes the object code smaller by 46 bytes.
Before:
text data bss dec hex filename
29812 3824 192 33828 8424 drivers/net/dsa/bcm_sf2.o
After:
text data bss dec hex filename
29670 3920 192 33782 83f6 drivers/net/dsa/bcm_sf2.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201020165029.56383-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix build errors when TLS=m, TLS_TOE=y, and CRYPTO_DEV_CHELSIO_TLS=y.
Having (tristate) CRYPTO_DEV_CHELSIO_TLS depend on (bool) TLS_TOE
is not strong enough to prevent the bad combination of TLS=m and
CRYPTO_DEV_CHELSIO_TLS=y, so add a dependency on TLS to prevent the
problematic kconfig combination.
Fixes these build errors:
hppa-linux-ld: drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_main.o: in function `chtls_free_uld':
drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_main.c:165: undefined reference to `tls_toe_unregister_device'
hppa-linux-ld: drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_main.o: in function `chtls_register_dev':
drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_main.c:204: undefined reference to `tls_toe_register_device'
Fixes: 53b4414a70 ("net/tls: allow compiling TLS TOE out")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20201019181059.22634-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When chtls_sock *csk is freed, same memory can be allocated
to different csk in chtls_sock_create().
csk->cdev = NULL; statement might ends up modifying wrong
csk, eventually causing kernel panic.
removing (csk->cdev = NULL) statement as it is not required.
Fixes: 3a0a978389 ("crypto/chtls: Fix chtls crash in connection cleanup")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the logic to compare net_device returned by ip_dev_find()
with the net_device list in cdev->ports[] array and return
net_device if matched else NULL.
Fixes: 6abde0b241 ("crypto/chtls: IPv6 support for inline TLS")
Signed-off-by: Venkatesh Ellapu <venkatesh.e@chelsio.com>
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Netdev is filled in egress_dev when connection is established,
If connection is closed before establishment, then egress_dev
is NULL, Fix it using ip_dev_find() rather then extracting from
egress_dev.
Fixes: 6abde0b241 ("crypto/chtls: IPv6 support for inline TLS")
Signed-off-by: Venkatesh Ellapu <venkatesh.e@chelsio.com>
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In chtls_sendpage() socket lock is released but not acquired,
fix it by taking lock.
Fixes: 36bedb3f2e ("crypto: chtls - Inline TLS record Tx")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the Realtek PHY driver will override any TX/RX delay
set by hardware straps if the phy-mode device property does not match.
This is causing problems on SynQuacer based platforms (the only SoC
that incorporates the netsec hardware), since many were built with
this Realtek PHY, and shipped with firmware that defines the phy-mode
as 'rgmii', even though the PHY is configured for TX and RX delay using
pull-ups.
From the driver's perspective, we should not make any assumptions in
the general case that the PHY hardware does not require any initial
configuration. However, the situation is slightly different for ACPI
boot, since it implies rich firmware with AML abstractions to handle
hardware details that are not exposed to the OS. So in the ACPI case,
it is reasonable to assume that the PHY comes up in the right mode,
regardless of whether the mode is set by straps, by boot time firmware
or by AML executed by the ACPI interpreter.
So let's ignore the 'phy-mode' device property when probing the netsec
driver in ACPI mode, and hardcode the mode to PHY_INTERFACE_MODE_NA,
which should work with any PHY provided that it is configured by the
time the driver attaches to it. While at it, document that omitting
the mode is permitted for DT probing as well, by setting the phy-mode
DT property to the empty string.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201018163625.2392-1-ardb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCX47RxAAKCRCAXGG7T9hj
vj7WAP94Cj5cQXPGaTD9GAVLVLgF6L2wPxUT1/gqLMulfRgHdAEAqVidg8fLhI6G
vgQiDwYp/svqZco2qA5i4YN+Xnr6Vg0=
=V/7G
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.10b-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- A single patch to fix the Xen security issue XSA-331 (malicious
guests can DoS dom0 by triggering NULL-pointer dereferences or access
to stale data).
- A larger series to fix the Xen security issue XSA-332 (malicious
guests can DoS dom0 by sending events at high frequency leading to
dom0's vcpus being busy in IRQ handling for elongated times).
* tag 'for-linus-5.10b-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: block rogue events for some time
xen/events: defer eoi in case of excessive number of events
xen/events: use a common cpu hotplug hook for event channels
xen/events: switch user event channels to lateeoi model
xen/pciback: use lateeoi irq binding
xen/pvcallsback: use lateeoi irq binding
xen/scsiback: use lateeoi irq binding
xen/netback: use lateeoi irq binding
xen/blkback: use lateeoi irq binding
xen/events: add a new "late EOI" evtchn framework
xen/events: fix race in evtchn_fifo_unmask()
xen/events: add a proper barrier to 2-level uevent unmasking
xen/events: avoid removing an event channel while handling it
In order to reduce the chance for the system becoming unresponsive due
to event storms triggered by a misbehaving netfront use the lateeoi
irq binding for netback and unmask the event channel only just before
going to sleep waiting for new events.
Make sure not to issue an EOI when none is pending by introducing an
eoi_pending element to struct xenvif_queue.
When no request has been consumed set the spurious flag when sending
the EOI for an interrupt.
This is part of XSA-332.
Cc: stable@vger.kernel.org
Reported-by: Julien Grall <julien@xen.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Wei Liu <wl@xen.org>
The VSC9953 Seville switch has 2 megabits of buffer split into 4360
words of 60 bytes each. 2048 * 1024 is 2 megabytes instead of 2 megabits.
2 megabits is (2048 / 8) * 1024 = 256 * 1024.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Fixes: a63ed92d21 ("net: dsa: seville: fix buffer size of the queue system")
Link: https://lore.kernel.org/r/20201019050625.21533-1-fido_max@inbox.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes gcc warning:
passing argument 1 of 'kfree' makes pointer from integer without a cast
Fixes: 3af5f0f5c7 ("net: korina: fix kfree of rx/tx descriptor array")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Link: https://lore.kernel.org/r/20201018184255.28989-1-vvidic@valentin-vidic.from.hr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For several network drivers it was reported that using
__napi_schedule_irqoff() is unsafe with forced threading. One way to
fix this is switching back to __napi_schedule, but then we lose the
benefit of the irqoff version in general. As stated by Eric it doesn't
make sense to make the minimal hard irq handlers in drivers using NAPI
a thread. Therefore ensure that the hard irq handler is never
thread-ified.
Fixes: 9a899a35b0 ("r8169: switch to napi_schedule_irqoff")
Link: https://lkml.org/lkml/2020/10/18/19
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/4d3ef84a-c812-5072-918a-22a6f6468310@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ian reports that after upgrade from v5.8.14 to v5.9 only one
of his 4 ixgbe netdevs appear in the system.
Quoting the comment on ixgbe_x550em_a_has_mii():
* Returns true if hw points to lowest numbered PCI B:D.F x550_em_a device in
* the SoC. There are up to 4 MACs sharing a single MDIO bus on the x550em_a,
* but we only want to register one MDIO bus.
This matches the symptoms, since the return value from
ixgbe_mii_bus_init() is no longer ignored we need to handle
the higher ports of x550em without an error.
Fixes: 09ef193fef ("net: ethernet: ixgbe: check the return value of ixgbe_mii_bus_init()")
Reported-by: Ian Kumlien <ian.kumlien@gmail.com>
Tested-by: Ian Kumlien <ian.kumlien@gmail.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20201016232006.3352947-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In set_ethernet_addr(), if get_registers() succeeds, the ethernet address
that was read must be copied over. Otherwise, a random ethernet address
must be assigned.
get_registers() returns 0 if successful, and negative error number
otherwise. However, in set_ethernet_addr(), this return value is
incorrectly checked.
Since this return value will never be equal to sizeof(node_id), a
random MAC address will always be generated and assigned to the
device; even in cases when get_registers() is successful.
Correctly modifying the condition that checks if get_registers() was
successful or not fixes this problem, and copies the ethernet address
appropriately.
Fixes: b2a0f274e3 ("net: rtl8150: Use the new usb control message API.")
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20201011173030.141582-1-anant.thazhemadam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The typical set of driver updates across the subsystem:
- Driver minor changes and bug fixes for mlx5, efa, rxe, vmw_pvrdma, hns,
usnic, qib, qedr, cxgb4, hns, bnxt_re
- Various rtrs fixes and updates
- Bug fix for mlx4 CM emulation for virtualization scenarios where MRA
wasn't working right
- Use tracepoints instead of pr_debug in the CM code
- Scrub the locking in ucma and cma to close more syzkaller bugs
- Use tasklet_setup in the subsystem
- Revert the idea that 'destroy' operations are not allowed to fail at
the driver level. This proved unworkable from a HW perspective.
- Revise how the umem API works so drivers make fewer mistakes using it
- XRC support for qedr
- Convert uverbs objects RWQ and MW to new the allocation scheme
- Large queue entry sizes for hns
- Use hmm_range_fault() for mlx5 On Demand Paging
- uverbs APIs to inspect the GID table instead of sysfs
- Move some of the RDMA code for building large page SGLs into
lib/scatterlist
-----BEGIN PGP SIGNATURE-----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=LKpl
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A usual cycle for RDMA with a typical mix of driver and core subsystem
updates:
- Driver minor changes and bug fixes for mlx5, efa, rxe, vmw_pvrdma,
hns, usnic, qib, qedr, cxgb4, hns, bnxt_re
- Various rtrs fixes and updates
- Bug fix for mlx4 CM emulation for virtualization scenarios where
MRA wasn't working right
- Use tracepoints instead of pr_debug in the CM code
- Scrub the locking in ucma and cma to close more syzkaller bugs
- Use tasklet_setup in the subsystem
- Revert the idea that 'destroy' operations are not allowed to fail
at the driver level. This proved unworkable from a HW perspective.
- Revise how the umem API works so drivers make fewer mistakes using
it
- XRC support for qedr
- Convert uverbs objects RWQ and MW to new the allocation scheme
- Large queue entry sizes for hns
- Use hmm_range_fault() for mlx5 On Demand Paging
- uverbs APIs to inspect the GID table instead of sysfs
- Move some of the RDMA code for building large page SGLs into
lib/scatterlist"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (191 commits)
RDMA/ucma: Fix use after free in destroy id flow
RDMA/rxe: Handle skb_clone() failure in rxe_recv.c
RDMA/rxe: Move the definitions for rxe_av.network_type to uAPI
RDMA: Explicitly pass in the dma_device to ib_register_device
lib/scatterlist: Do not limit max_segment to PAGE_ALIGNED values
IB/mlx4: Convert rej_tmout radix-tree to XArray
RDMA/rxe: Fix bug rejecting all multicast packets
RDMA/rxe: Fix skb lifetime in rxe_rcv_mcast_pkt()
RDMA/rxe: Remove duplicate entries in struct rxe_mr
IB/hfi,rdmavt,qib,opa_vnic: Update MAINTAINERS
IB/rdmavt: Fix sizeof mismatch
MAINTAINERS: CISCO VIC LOW LATENCY NIC DRIVER
RDMA/bnxt_re: Fix sizeof mismatch for allocation of pbl_tbl.
RDMA/bnxt_re: Use rdma_umem_for_each_dma_block()
RDMA/umem: Move to allocate SG table from pages
lib/scatterlist: Add support in dynamic allocation of SG table from pages
tools/testing/scatterlist: Show errors in human readable form
tools/testing/scatterlist: Rejuvenate bit-rotten test
RDMA/ipoib: Set rtnl_link_ops for ipoib interfaces
RDMA/uverbs: Expose the new GID query API to user space
...
The below compile time error can be seen when PHYLIB is configured as a
module.
ld: drivers/net/pcs/pcs-xpcs.o: in function `xpcs_read':
pcs-xpcs.c:(.text+0x29): undefined reference to `mdiobus_read'
ld: drivers/net/pcs/pcs-xpcs.o: in function `xpcs_soft_reset.constprop.7':
pcs-xpcs.c:(.text+0x80): undefined reference to `mdiobus_write'
ld: drivers/net/pcs/pcs-xpcs.o: in function `xpcs_config_aneg':
pcs-xpcs.c:(.text+0x318): undefined reference to `mdiobus_write'
ld: pcs-xpcs.c:(.text+0x38e): undefined reference to `mdiobus_write'
ld: pcs-xpcs.c:(.text+0x3eb): undefined reference to `mdiobus_write'
ld: pcs-xpcs.c:(.text+0x437): undefined reference to `mdiobus_write'
ld: drivers/net/pcs/pcs-xpcs.o:pcs-xpcs.c:(.text+0xb1e): more undefined references to `mdiobus_write' follow
PHYLIB being a module leads to MDIO_BUS being a module as well while the
XPCS is still built-in. What should happen in this configuration is that
PCS_XPCS should be forced to build as module. However, that select only
acts in the opposite way so we should turn it into a depends.
Fix this up by explicitly depending on MDIO_BUS.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Fixes: 2fa4e4b799 ("net: pcs: Move XPCS into new PCS subdirectory")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The new HW arbitration feature on Aspeed ast2600 will cause MAC TX to
hang when handling scatter-gather DMA. Disable the problematic feature
by setting MAC register 0x58 bit28 and bit27.
Fixes: 39bfab8844 ("net: ftgmac100: Add support for DT phy-handle property")
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=26wi
-----END PGP SIGNATURE-----
Merge tag 'docs/v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull documentation updates from Mauro Carvalho Chehab:
"A series of patches addressing warnings produced by make htmldocs.
This includes:
- kernel-doc markup fixes
- ReST fixes
- Updates at the build system in order to support newer versions of
the docs build toolchain (Sphinx)
After this series, the number of html build warnings should reduce
significantly, and building with Sphinx 3.1 or later should now be
supported (although it is still recommended to use Sphinx 2.4.4).
As agreed with Jon, I should be sending you a late pull request by the
end of the merge window addressing remaining issues with docs build,
as there are a number of warning fixes that depends on pull requests
that should be happening along the merge window.
The end goal is to have a clean htmldocs build on Kernel 5.10.
PS. It should be noticed that Sphinx 3.0 is not currently supported,
as it lacks support for C domain namespaces. Such feature, needed in
order to document uAPI system calls with Sphinx 3.x, was added only on
Sphinx 3.1"
* tag 'docs/v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (75 commits)
PM / devfreq: remove a duplicated kernel-doc markup
mm/doc: fix a literal block markup
workqueue: fix a kernel-doc warning
docs: virt: user_mode_linux_howto_v2.rst: fix a literal block markup
Input: sparse-keymap: add a description for @sw
rcu/tree: docs: document bkvcache new members at struct kfree_rcu_cpu
nl80211: docs: add a description for s1g_cap parameter
usb: docs: document altmode register/unregister functions
kunit: test.h: fix a bad kernel-doc markup
drivers: core: fix kernel-doc markup for dev_err_probe()
docs: bio: fix a kerneldoc markup
kunit: test.h: solve kernel-doc warnings
block: bio: fix a warning at the kernel-doc markups
docs: powerpc: syscall64-abi.rst: fix a malformed table
drivers: net: hamradio: fix document location
net: appletalk: Kconfig: Fix docs location
dt-bindings: fix references to files converted to yaml
memblock: get rid of a :c:type leftover
math64.h: kernel-docs: Convert some markups into normal comments
media: uAPI: buffer.rst: remove a left-over documentation
...
From Maor Gottlieb says:
====================
This series extends __sg_alloc_table_from_pages to allow chaining of new
pages to an already initialized SG table.
This allows for drivers to utilize the optimization of merging contiguous
pages without a need to pre allocate all the pages and hold them in a very
large temporary buffer prior to the call to SG table initialization.
The last patch changes the Infiniband core to use the new API. It removes
duplicate functionality from the code and benefits from the optimization
of allocating dynamic SG table from pages.
In huge pages system of 2MB page size, without this change, the SG table
would contain x512 SG entries.
====================
* branch 'dynamic_sg':
RDMA/umem: Move to allocate SG table from pages
lib/scatterlist: Add support in dynamic allocation of SG table from pages
tools/testing/scatterlist: Show errors in human readable form
tools/testing/scatterlist: Rejuvenate bit-rotten test
Add redirect_neigh() BPF packet redirect helper, allowing to limit stack
traversal in common container configs and improving TCP back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
Expand netlink policy support and improve policy export to user space.
(Ge)netlink core performs request validation according to declared
policies. Expand the expressiveness of those policies (min/max length
and bitmasks). Allow dumping policies for particular commands.
This is used for feature discovery by user space (instead of kernel
version parsing or trial and error).
Support IGMPv3/MLDv2 multicast listener discovery protocols in bridge.
Allow more than 255 IPv4 multicast interfaces.
Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
In Multi-patch TCP (MPTCP) support concurrent transmission of data
on multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
Support SMC-Dv2 version of SMC, which enables multi-subnet deployments.
Allow more calls to same peer in RxRPC.
Support two new Controller Area Network (CAN) protocols -
CAN-FD and ISO 15765-2:2016.
Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
Add TC actions for implementing MPLS L2 VPNs.
Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary notifications
and make it easier to offload nexthops into HW by converting
to a blocking notifier.
Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific
TCP option use.
Reorganize TCP congestion control (CC) initialization to simplify life
of TCP CC implemented in BPF.
Add support for shipping BPF programs with the kernel and loading them
early on boot via the User Mode Driver mechanism, hence reusing all the
user space infra we have.
Support sleepable BPF programs, initially targeting LSM and tracing.
Add bpf_d_path() helper for returning full path for given 'struct path'.
Make bpf_tail_call compatible with bpf-to-bpf calls.
Allow BPF programs to call map_update_elem on sockmaps.
Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
Support listing and getting information about bpf_links via the bpf
syscall.
Enhance kernel interfaces around NIC firmware update. Allow specifying
overwrite mask to control if settings etc. are reset during update;
report expected max time operation may take to users; support firmware
activation without machine reboot incl. limits of how much impact
reset may have (e.g. dropping link or not).
Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
Adopt or extend devlink use for debug, monitoring, fw update
in many drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw,
mv88e6xxx, dpaa2-eth).
In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
Add XDP support for Intel's igb driver.
Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
Improve performance for packets which don't require much offloads
on recent Mellanox NICs by 20% by making multiple packets share
a descriptor entry.
Move chelsio inline crypto drivers (for TLS and IPsec) from the crypto
subtree to drivers/net. Move MDIO drivers out of the phy directory.
Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=bc1U
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common
code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
-----BEGIN PGP SIGNATURE-----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=Bkf/
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
* tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping: (63 commits)
ARM/ixp4xx: add a missing include of dma-map-ops.h
dma-direct: simplify the DMA_ATTR_NO_KERNEL_MAPPING handling
dma-direct: factor out a dma_direct_alloc_from_pool helper
dma-direct check for highmem pages in dma_direct_alloc_pages
dma-mapping: merge <linux/dma-noncoherent.h> into <linux/dma-map-ops.h>
dma-mapping: move large parts of <linux/dma-direct.h> to kernel/dma
dma-mapping: move dma-debug.h to kernel/dma/
dma-mapping: remove <asm/dma-contiguous.h>
dma-mapping: merge <linux/dma-contiguous.h> into <linux/dma-map-ops.h>
dma-contiguous: remove dma_contiguous_set_default
dma-contiguous: remove dev_set_cma_area
dma-contiguous: remove dma_declare_contiguous
dma-mapping: split <linux/dma-mapping.h>
cma: decrease CMA_ALIGNMENT lower limit to 2
firewire-ohci: use dma_alloc_pages
dma-iommu: implement ->alloc_noncoherent
dma-mapping: add new {alloc,free}_noncoherent dma_map_ops methods
dma-mapping: add a new dma_alloc_pages API
dma-mapping: remove dma_cache_sync
53c700: convert to dma_alloc_noncoherent
...
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get
wrong, as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception of
the last "obviously correct" patch that updated a FALLTHROUGH comment
that got merged last weekend.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4hAAg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfRACcCp48StLg4V7XcZ41eQYES/DVwxkAnjnZs+La
Y7F+o2p8DiuLLQamdEyB
=lHr1
-----END PGP SIGNATURE-----
Merge tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY/Thunderbolt driver updates from Greg KH:
"Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get wrong,
as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception
of the last "obviously correct" patch that updated a FALLTHROUGH
comment that got merged last weekend"
* tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (374 commits)
usb: musb: gadget: Use fallthrough pseudo-keyword
usb: typec: Add QCOM PMIC typec detection driver
USB: serial: option: add Cellient MPL200 card
usb: typec: tcpci_maxim: Add support for Sink FRS
usb: typec: tcpci: Implement callbacks for FRS
usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)
usb: typec: tcpci_maxim: Chip level TCPC driver
usb: typec: tcpci: Add set_vbus tcpci callback
usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference
usbip: vhci_hcd: fix calling usb_hcd_giveback_urb() with irqs enabled
usb: cdc-acm: add quirk to blacklist ETAS ES58X devices
USB: serial: ftdi_sio: use cur_altsetting for consistency
USB: serial: option: Add Telit FT980-KS composition
USB: core: remove polling for /sys/kernel/debug/usb/devices
usb: typec: add support for STUSB160x Type-C controller family
usb: typec: add typec_find_pwr_opmode
usb: typec: hd3ss3220: Use OF graph API to get the connector fwnode
dt-bindings: usb: renesas,usb3-peri: Document HS and SS data bus
dt-bindings: usb: convert ti,hd3ss3220 bindings to json-schema
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
...
Here is the large set of staging and IIO driver updates for 5.10-rc1.
Included in here are:
- new IIO drivers
- new IIO driver frameworks
- various IIO driver fixes and updates
- IIO device tree conversions to yaml
- so many minor staging driver coding style cleanups
- most cdev driver moved out of staging
- no new drivers added or removed
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4g+oQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymAyQCghI58tN/Np3itPlZuc+HYFN7OHH8An1TKzCm1
bwkfw5qAcHab+R7KQZOA
=BaXS
-----END PGP SIGNATURE-----
Merge tag 'staging-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO driver updates from Greg KH:
"Here is the large set of staging and IIO driver updates for 5.10-rc1.
Included in here are:
- new IIO drivers
- new IIO driver frameworks
- various IIO driver fixes and updates
- IIO device tree conversions to yaml
- so many minor staging driver coding style cleanups
- most cdev driver moved out of staging
- no staging drivers added or removed
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (476 commits)
staging: comedi: check validity of wMaxPacketSize of usb endpoints found
staging: wfx: improve robustness of wfx_get_hw_rate()
staging: wfx: drop unicode characters from strings
staging: wfx: gpiod_get_value() can return an error
staging: wfx: increase robustness of hif_generic_confirm()
staging: wfx: wfx_init_common() returns NULL on error
staging: wfx: standardize the error when vif does not exist
staging: wfx: check memory allocation
staging: wfx: improve error handling of hif_join()
staging: dpaa2-switch: add a dpaa2_switch prefix to all functions in ethsw.c
staging: dpaa2-switch: add a dpaa2_switch_ prefix to all functions in ethsw-ethtool.c
staging: rtl8188eu: Fix long lines
dt-bindings: staging: wfx: silabs,wfx yaml conversion
staging: wfx: update copyrights dates
staging: wfx: fix QoS priority for slow buses
staging: wfx: fix BA sessions for older firmwares
staging: wfx: remove remaining code of 'secure link' feature
staging: wfx: fix handling of MMIC error
staging: vchiq: Fix list_for_each exit tests
staging: greybus: use __force when assigning __u8 value to snd_ctl_elem_type_t
...
This patch changes the module name to "ch_ipsec" and prepends
"ch_ipsec" string instead of "chcr" in all debug messages and
function names.
V1->V2:
-Removed inline keyword from functions.
-Removed CH_IPSEC prefix from pr_debug.
-Used proper indentation for the continuation line of the function
arguments.
V2->V3:
Fix the checkpatch.pl warnings.
Fixes: 1b77be4639 ("crypto/chcr: Moving chelsio's inline ipsec functionality to /drivers/net")
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hamradio docs were moved to a different dir.
Update its location accordingly.
Fixes: 1447495025 ("docs: networking: move z8530 to the hw driver section")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The location of ltpc.rst changed. Update it at Kconfig.
Fixes: 4daedf7abb ("docs: networking: move AppleTalk / LocalTalk drivers to the hw driver section")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ingress large send packets are identified by either:
The IBMVETH_RXQ_LRG_PKT flag in the receive buffer
or with a -1 placed in the ip header checksum.
The method used depends on firmware version. Frame
geometry and sufficient header validation is performed by the
hypervisor eliminating the need for further header checks here.
Fixes: 7b5967389f ("ibmveth: set correct gso_size and gso_type")
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Reviewed-by: Cristobal Forno <cris.forno@ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ibmveth_rx_csum_helper() must be called after ibmveth_rx_mss_helper()
as ibmveth_rx_csum_helper() may alter ip and tcp checksum values.
Fixes: 66aa0678ef ("ibmveth: Support to enable LSO/CSO for Trunk VEA.")
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Reviewed-by: Cristobal Forno <cris.forno@ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 4-tuple NAT offload via PEDIT always overwrites all the 4-tuple
fields even if they had not been explicitly enabled. If any fields in
the 4-tuple are not enabled, then the hardware overwrites the
disabled fields with zeros, instead of ignoring them.
So, add a parser that can translate the enabled 4-tuple PEDIT fields
to one of the NAT mode combinations supported by the hardware and
hence avoid overwriting disabled fields to 0. Any rule with
unsupported NAT mode combination is rejected.
Signed-off-by: Herat Ramani <herat@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here are some SPDX-specific changes for 5.10-rc1.
They include:
- driver fixes to make spdxcheck.pl work properly
- add GFDL licenses as "deprecated" but required due to some of
our documentation using them
- add Zlib license as "deprecated" but required because we have
code with this license in the tree.
- convert some drivers to have SPDX identifiers that previously
didn't have them.
All have been in linux-next for a very long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4c6oA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl35ACg2i+pP5CBExSzQUtA1Tx/UD2CVNMAoIAQChwj
SHZurDuyHkEiCdB+5n1u
=C9qR
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here are some SPDX-specific changes for 5.10-rc1.
They include:
- driver fixes to make spdxcheck.pl work properly
- add GFDL licenses as "deprecated" but required due to some of our
documentation using them
- add Zlib license as "deprecated" but required because we have code
with this license in the tree.
- convert some drivers to have SPDX identifiers that previously
didn't have them.
All have been in linux-next for a very long time with no reported
issues"
* tag 'spdx-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
scripts/spdxcheck.py: handle license identifiers in XML comments
net/mlx5: IPsec: make spdxcheck.py happy
LICENSES/deprecated: add Zlib license text
LICENSE: add GFDL deprecated licenses
net/qla3xxx: Convert to SPDX license identifiers
net/qlge: Convert to SPDX license identifiers
net/qlcnic: Convert to SPDX license identifiers
scsi/qla2xxx: Convert to SPDX license identifiers
scsi/qla4xxx: Convert to SPDX license identifiers
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAl+FqrsTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXnN8B/4sRg7j9OTzVBlDiXF2vj6vbuplTIH6
JR6S5f4PNjUg4gV6ghzSnsx1zqNhPSOr78zDqYto8vv+wqqj3thmld8+gAnSbKtt
yoAa7mhbbN1ryJiwPlZzvX4ApzGZPC7byqEi3+zPIcag6TEl8eyYJOmvY3x1zv8x
CsAb57oCC4erD0n4xlTyfuc8TLpO+EiU53PXbR9AovKQHe4m2/8LWyEbmrm5cRUR
gx8RxoLkkrqK0unzcmanbm47QodiaOTUpycs3IvaBeWZQsqSgFZdI1RAdTZNg+U+
GT8eMRXAwpgDpilPm/0n1O0PKGAsVh9Lbw8Btb/ggqnjTUlA4Z3Df23E
=Wy5n
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V updates from Wei Liu:
- a series from Boqun Feng to support page size larger than 4K
- a few miscellaneous clean-ups
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hv: clocksource: Add notrace attribute to read_hv_sched_clock_*() functions
x86/hyperv: Remove aliases with X64 in their name
PCI: hv: Document missing hv_pci_protocol_negotiation() parameter
scsi: storvsc: Support PAGE_SIZE larger than 4K
Driver: hv: util: Use VMBUS_RING_SIZE() for ringbuffer sizes
HID: hyperv: Use VMBUS_RING_SIZE() for ringbuffer sizes
Input: hyperv-keyboard: Use VMBUS_RING_SIZE() for ringbuffer sizes
hv_netvsc: Use HV_HYP_PAGE_SIZE for Hyper-V communication
hv: hyperv.h: Introduce some hvpfn helper functions
Drivers: hv: vmbus: Move virt_to_hvpfn() to hyperv header
Drivers: hv: Use HV_HYP_PAGE in hv_synic_enable_regs()
Drivers: hv: vmbus: Introduce types of GPADL
Drivers: hv: vmbus: Move __vmbus_open()
Drivers: hv: vmbus: Always use HV_HYP_PAGE_SIZE for gpadl
drivers: hv: remove cast from hyperv_die_event
The e1000_clear_vfta function was triggering a warning in kbuild-bot
testing. It's actually a bug but has no functional impact.
drivers/net/ethernet/intel/e1000/e1000_hw.c:4415:58: warning: Same expression in both branches of ternary operator. [duplicateExpressionTernary]
Fix this warning by removing the offending code and simplifying
the routine to do exactly what it did before, no functional
change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Starting with API version 1.10 firmware for X722 devices has ability
to change FEC settings in PHY. Code added in this patch allows
changing FEC settings if the capability flag indicates the device
supports this feature.
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simplify the code by using new function dev_fetch_sw_netstats().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/166259f2-084c-45d7-e610-2de2a0bdae06@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow user configuring RXCSUM separately with ethtool -K,
reusing the existing virtnet_set_guest_offloads helper
that configures RXCSUM for XDP. This is conditional on
VIRTIO_NET_F_CTRL_GUEST_OFFLOADS.
If Rx checksum is disabled, LRO should also be disabled.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20201012015820.62042-1-xiangxia.m.yue@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A helper for checking whether a net_device belongs to mscc_ocelot
already existed and did not need to be rewritten. Use it.
Fixes: 319e4dd11a ("net: mscc: ocelot: introduce conversion helpers between port and netdev")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201011092041.3535101-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The at91rm9200 variant used by a few chips including the MSC313 supports
two Tx descriptors (one frame being serialized and another one queued).
However the driver only implemented a single one, which adds a dead time
after each transfer to receive and process the interrupt and wake the
queue up, preventing from reaching line rate.
This patch implements a very basic 2-deep queue to address this limitation.
The tests run on a Breadbee board equipped with an MSC313E show that at
1 GHz, HTTP traffic on medium-sized objects (45kB) was limited to exactly
50 Mbps before this patch, and jumped to 76 Mbps with this patch. And tests
on a single TCP stream with an MTU of 576 jump from 10kpps to 15kpps. With
1500 byte packets it's now possible to reach line rate versus 75 Mbps
before.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20201011090944.10607-4-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RM9200 supports one frame being sent while another one is waiting in
queue. This avoids the dead time that follows the emission of a frame
and which prevents one from reaching line speed.
Right now the driver supports only a single skb, so we'll first replace
the rm9200-specific skb info with an array of two macb_tx_skb (already
used by other drivers). This patch only moves the skb_length to
txq[0].size and skb_physaddr to skb[0].mapping but doesn't perform any
other change. It already uses [desc] in order to minimize future changes.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20201011090944.10607-3-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Transmit Buffer Register Empty replaces TXERR on RM9200 and signals the
sender may try to send again becase the last queued frame is no longer
in queue (being transmitted or already transmitted).
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20201011090944.10607-2-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull crypto updates from Herbert Xu:
"API:
- Allow DRBG testing through user-space af_alg
- Add tcrypt speed testing support for keyed hashes
- Add type-safe init/exit hooks for ahash
Algorithms:
- Mark arc4 as obsolete and pending for future removal
- Mark anubis, khazad, sead and tea as obsolete
- Improve boot-time xor benchmark
- Add OSCCA SM2 asymmetric cipher algorithm and use it for integrity
Drivers:
- Fixes and enhancement for XTS in caam
- Add support for XIP8001B hwrng in xiphera-trng
- Add RNG and hash support in sun8i-ce/sun8i-ss
- Allow imx-rngc to be used by kernel entropy pool
- Use crypto engine in omap-sham
- Add support for Ingenic X1830 with ingenic"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (205 commits)
X.509: Fix modular build of public_key_sm2
crypto: xor - Remove unused variable count in do_xor_speed
X.509: fix error return value on the failed path
crypto: bcm - Verify GCM/CCM key length in setkey
crypto: qat - drop input parameter from adf_enable_aer()
crypto: qat - fix function parameters descriptions
crypto: atmel-tdes - use semicolons rather than commas to separate statements
crypto: drivers - use semicolons rather than commas to separate statements
hwrng: mxc-rnga - use semicolons rather than commas to separate statements
hwrng: iproc-rng200 - use semicolons rather than commas to separate statements
hwrng: stm32 - use semicolons rather than commas to separate statements
crypto: xor - use ktime for template benchmarking
crypto: xor - defer load time benchmark to a later time
crypto: hisilicon/zip - fix the uninitalized 'curr_qm_qp_num'
crypto: hisilicon/zip - fix the return value when device is busy
crypto: hisilicon/zip - fix zero length input in GZIP decompress
crypto: hisilicon/zip - fix the uncleared debug registers
lib/mpi: Fix unused variable warnings
crypto: x86/poly1305 - Remove assignments with no effect
hwrng: npcm - modify readl to readb
...
Pull copy_and_csum cleanups from Al Viro:
"Saner calling conventions for csum_and_copy_..._user() and friends"
[ Removing 800+ lines of code and cleaning stuff up is good - Linus ]
* 'work.csum_and_copy' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ppc: propagate the calling conventions change down to csum_partial_copy_generic()
amd64: switch csum_partial_copy_generic() to new calling conventions
sparc64: propagate the calling convention changes down to __csum_partial_copy_...()
xtensa: propagate the calling conventions change down into csum_partial_copy_generic()
mips: propagate the calling convention change down into __csum_partial_copy_..._user()
mips: __csum_partial_copy_kernel() has no users left
mips: csum_and_copy_{to,from}_user() are never called under KERNEL_DS
sparc32: propagate the calling conventions change down to __csum_partial_copy_sparc_generic()
i386: propagate the calling conventions change down to csum_partial_copy_generic()
sh: propage the calling conventions change down to csum_partial_copy_generic()
m68k: get rid of zeroing destination on error in csum_and_copy_from_user()
arm: propagate the calling convention changes down to csum_partial_copy_from_user()
alpha: propagate the calling convention changes down to csum_partial_copy.c helpers
saner calling conventions for csum_and_copy_..._user()
csum_and_copy_..._user(): pass 0xffffffff instead of 0 as initial sum
csum_partial_copy_nocheck(): drop the last argument
unify generic instances of csum_partial_copy_nocheck()
icmp_push_reply(): reorder adding the checksum up
skb_copy_and_csum_bits(): don't bother with the last argument
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-10-12
The main changes are:
1) The BPF verifier improvements to track register allocation pattern, from Alexei and Yonghong.
2) libbpf relocation support for different size load/store, from Andrii.
3) bpf_redirect_peer() helper and support for inner map array with different max_entries, from Daniel.
4) BPF support for per-cpu variables, form Hao.
5) sockmap improvements, from John.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new FTE in TX IPsec FT per IPsec state. It has the
same matching criteria as the RX steering rule.
The IPsec FT is created/destroyed when the first/last rule
is added/deleted respectively.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add new namespace that represents the NIC TX domain.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently the error exit path err_free kfree's attr. In the case where
flow and parse_attr failed to be allocated this return path will free
the uninitialized pointer attr, which is not correct. In the other
case where attr fails to allocate attr does not need to be freed. So
in both error exits via err_free attr should not be freed, so remove
it.
Addresses-Coverity: ("Uninitialized pointer read")
Fixes: ff7ea04ad5 ("net/mlx5e: Fix potential null pointer dereference")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This patch adds FW versions stored in the flash to devlink info_get
callback. Return the correct fw.psid running version using the
newly added bp->nvm_cfg_ver.
v2:
Ensure stored pkg_name string is NULL terminated when copied to
devlink.
Return directly from the last call to bnxt_dl_info_put().
If the FW call to get stored version fails for any reason, return
success immediately to devlink without the stored versions.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-10-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a new function bnxt_dl_info_put() to simplify the code, as there
are more stored firmware version fields to be added in the next patch.
Also, rename fw_ver variable name to ncsi_ver for better naming while
copying to devlink info_get cb.
v2:
Ensure active_pkg_name string is NULL terminated when copied to
devlink.
Return directly from the last call to bnxt_dl_info_put().
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-9-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a new bnxt_hwrm_nvm_get_dev_info() to query firmware version
information via NVM_GET_DEV_INFO firmware command. Use it to
get the running version of the NVM configuration information.
This new function will also be used in subsequent patches to get the
stored firmware versions.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-8-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the VF virtual link is set to always enabled, the speed may be
unknown when the physical link is down. The driver currently logs
the link speed as 4294967295 Mbps which is SPEED_UNKNOWN. Modify
the link up log message as "speed unknown" which makes more sense.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-7-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
event_data1 and event_data2 are used when processing most events.
Store these in local variables at the beginning of the function to
simplify many of the case statements.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-5-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, bp->msg_enable has default value of 0. It is more useful
to have the commonly used NETIF_MSG_DRV and NETIF_MSG_HW enabled by
default.
v2: Change the fall back bnxt_reset_task() inside bnxt_rx_ring_reset()
to silent mode. With older fw, we would take the fall back path and
it would be very noisy.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-4-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Online self tests are not disruptive and can be run in NPAR mode
and in multi-host NIC as well.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-3-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If NVRAM resources are locked, NVM writes are not permitted. In such
scenarios, firmware returns HWRM_ERR_CODE_RESOURCE_LOCKED error to
firmware commands.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-2-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phy_reset_after_clk_enable() is always called with ndev->phydev,
however that pointer may be NULL even though the PHY device instance
already exists and is sufficient to perform the PHY reset.
This condition happens in fec_open(), where the clock must be enabled
first, then the PHY must be reset, and then the PHY IDs can be read
out of the PHY.
If the PHY still is not bound to the MAC, but there is OF PHY node
and a matching PHY device instance already, use the OF PHY node to
obtain the PHY device instance, and then use that PHY device instance
when triggering the PHY reset.
Fixes: 1b0a83ac04 ("net: fec: add phy_reset_after_clk_enable() support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Richard Leitner <richard.leitner@skidata.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netcons calls napi_poll with a budget of 0 to transmit packets.
Handle this by:
- skipping RX processing
- do not try to recycle TX packets to the RX cache
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kmalloc returns KSEG0 addresses so convert back from KSEG1
in kfree. Also make sure array is freed when the driver is
unloaded from the kernel.
Fixes: ef11291bcd ("Add support the Korina (IDT RC32434) Ethernet MAC")
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Between queuing the delayed work and finishing the setup of the dsa
ports, the process may sleep in request_module() (via
phy_device_create()) and the queued work may be executed prior to the
switch net devices being registered. In ksz_mib_read_work(), a NULL
dereference will happen within netof_carrier_ok(dp->slave).
Not queuing the delayed work in ksz_init_mib_timer() makes things even
worse because the work will now be queued for immediate execution
(instead of 2000 ms) in ksz_mac_link_down() via
dsa_port_link_register_of().
Call tree:
ksz9477_i2c_probe()
\--ksz9477_switch_register()
\--ksz_switch_register()
+--dsa_register_switch()
| \--dsa_switch_probe()
| \--dsa_tree_setup()
| \--dsa_tree_setup_switches()
| +--dsa_switch_setup()
| | +--ksz9477_setup()
| | | \--ksz_init_mib_timer()
| | | |--/* Start the timer 2 seconds later. */
| | | \--schedule_delayed_work(&dev->mib_read, msecs_to_jiffies(2000));
| | \--__mdiobus_register()
| | \--mdiobus_scan()
| | \--get_phy_device()
| | +--get_phy_id()
| | \--phy_device_create()
| | |--/* sleeping, ksz_mib_read_work() can be called meanwhile */
| | \--request_module()
| |
| \--dsa_port_setup()
| +--/* Called for non-CPU ports */
| +--dsa_slave_create()
| | +--/* Too late, ksz_mib_read_work() may be called beforehand */
| | \--port->slave = ...
| ...
| +--Called for CPU port */
| \--dsa_port_link_register_of()
| \--ksz_mac_link_down()
| +--/* mib_read must be initialized here */
| +--/* work is already scheduled, so it will be executed after 2000 ms */
| \--schedule_delayed_work(&dev->mib_read, 0);
\-- /* here port->slave is setup properly, scheduling the delayed work should be safe */
Solution:
1. Do not queue (only initialize) delayed work in ksz_init_mib_timer().
2. Only queue delayed work in ksz_mac_link_down() if init is completed.
3. Queue work once in ksz_switch_register(), after dsa_register_switch()
has completed.
Fixes: 7c6ff470aa ("net: dsa: microchip: add MIB counter reading support")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the router is rebooted without a power cycle, the USB device
remains connected but its configuration is reset. This results in
a non-working ethernet connection with messages like this in syslog:
usb 2-2: RX packet too long: 65535 B
Re-enable ethernet mode when receiving a packet with invalid size of
0xffff.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VCAP_IS1_ACT_VID_REPLACE_ENA action, from the VCAP IS1 ingress TCAM,
changes the classified VLAN.
We are only exposing this ability for switch ports that are under VLAN
aware bridges. This is because in standalone ports mode and under a
bridge with vlan_filtering=0, the ocelot driver configures the switch to
operate as VLAN-unaware, so the classified VLAN is not derived from the
802.1Q header from the packet, but instead is always equal to the
port-based VLAN ID of the ingress port. We _can_ still change the
classified VLAN for packets when operating in this mode, but the end
result will most likely be a drop, since both the ingress and the egress
port need to be members of the modified VLAN. And even if we install the
new classified VLAN into the VLAN table of the switch, the result would
still not be as expected: we wouldn't see, on the output port, the
modified VLAN tag, but the original one, even though the classified VLAN
was indeed modified. This is because of how the hardware works: on
egress, what is pushed to the frame is a "port tag", which gives us the
following options:
- Tag all frames with port tag (derived from the classified VLAN)
- Tag all frames with port tag, except if the classified VLAN is 0 or
equal to the native VLAN of the egress port
- No port tag
Needless to say, in VLAN-unaware mode we are disabling the port tag.
Otherwise, the existing VLAN tag would be ignored, and a second VLAN
tag (the port tag), holding the classified VLAN, would be pushed
(instead of replacing the existing 802.1Q tag). This is definitely not
what the user wanted when installing a "vlan modify" action.
So it is simply not worth bothering with VLAN modify rules under other
configurations except when the ports are fully VLAN-aware.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a methodical transition of the driver from phylib
to phylink, following the guidelines from sfp-phylink.rst.
The MAC register configurations based on interface mode
were moved from the probing path to the mac_config() hook.
MAC enable and disable commands (enabling Rx and Tx paths
at MAC level) were also extracted and assigned to their
corresponding phylink hooks.
As part of the migration to phylink, the serdes configuration
from the driver was offloaded to the PCS_LYNX module,
introduced in commit 0da4c3d393 ("net: phy: add Lynx PCS module"),
the PCS_LYNX module being a mandatory component required to
make the enetc driver work with phylink.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.cionei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Decouple internal mdio bus creation from serdes
configuration, as a prerequisite to offloading
serdes configuration to a different module.
Group together mdio bus creation routines, cleanup.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Decouple level MAC configuration based on phy interface type
from general port configuration.
Group together MAC and link configuration code.
Decouple external mdio bus creation from interface type
parsing. No longer return an (unhandled) error code when
phy_node not found, use phy_node to indicate whether the
port has a phy or not. No longer fall-through when serdes
configuration fails for the link modes that require
internal link configuration.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add an efficient ingress to ingress netns switch that can be used out of tc BPF
programs in order to redirect traffic from host ns ingress into a container
veth device ingress without having to go via CPU backlog queue [0]. For local
containers this can also be utilized and path via CPU backlog queue only needs
to be taken once, not twice. On a high level this borrows from ipvlan which does
similar switch in __netif_receive_skb_core() and then iterates via another_round.
This helps to reduce latency for mentioned use cases.
Pod to remote pod with redirect(), TCP_RR [1]:
# percpu_netperf 10.217.1.33
RT_LATENCY: 122.450 (per CPU: 122.666 122.401 122.333 122.401 )
MEAN_LATENCY: 121.210 (per CPU: 121.100 121.260 121.320 121.160 )
STDDEV_LATENCY: 120.040 (per CPU: 119.420 119.910 125.460 115.370 )
MIN_LATENCY: 46.500 (per CPU: 47.000 47.000 47.000 45.000 )
P50_LATENCY: 118.500 (per CPU: 118.000 119.000 118.000 119.000 )
P90_LATENCY: 127.500 (per CPU: 127.000 128.000 127.000 128.000 )
P99_LATENCY: 130.750 (per CPU: 131.000 131.000 129.000 132.000 )
TRANSACTION_RATE: 32666.400 (per CPU: 8152.200 8169.842 8174.439 8169.897 )
Pod to remote pod with redirect_peer(), TCP_RR:
# percpu_netperf 10.217.1.33
RT_LATENCY: 44.449 (per CPU: 43.767 43.127 45.279 45.622 )
MEAN_LATENCY: 45.065 (per CPU: 44.030 45.530 45.190 45.510 )
STDDEV_LATENCY: 84.823 (per CPU: 66.770 97.290 84.380 90.850 )
MIN_LATENCY: 33.500 (per CPU: 33.000 33.000 34.000 34.000 )
P50_LATENCY: 43.250 (per CPU: 43.000 43.000 43.000 44.000 )
P90_LATENCY: 46.750 (per CPU: 46.000 47.000 47.000 47.000 )
P99_LATENCY: 52.750 (per CPU: 51.000 54.000 53.000 53.000 )
TRANSACTION_RATE: 90039.500 (per CPU: 22848.186 23187.089 22085.077 21919.130 )
[0] https://linuxplumbersconf.org/event/7/contributions/674/attachments/568/1002/plumbers_2020_cilium_load_balancer.pdf
[1] https://github.com/borkmann/netperf_scripts/blob/master/percpu_netperf
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201010234006.7075-3-daniel@iogearbox.net
Move the skb_headroom check out of fr_hard_header and into pvc_xmit.
This has two benefits:
1. Originally we only do this check for skbs sent by users on Ethernet-
emulating PVC devices. After the change we do this check for skbs sent on
normal PVC devices, too.
(Also add a comment to make it clear that this is only a protection
against upper layers that don't take dev->needed_headroom into account.
Such upper layers should be rare and I believe they should be fixed.)
2. After the change we can simplify the parameter list of fr_hard_header.
We no longer need to use a pointer to pointers (skb_p) because we no
longer need to replace the skb inside fr_hard_header.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MTU setting for this DSA switch is global so we need
to keep track of the MTU set for each port, then as soon
as any MTU changes, roof the MTU to the biggest common
denominator and poke that into the switch MTU setting.
To achieve this we need a per-chip-variant state container
for the RTL8366RB to use for the RTL8366RB-specific
stuff. Other SMI switches does seem to have per-port
MTU setting capabilities.
Fixes: 5f4a8ef384 ("net: dsa: rtl8366rb: Support setting MTU")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Better place for of_mdio.c is drivers/net/mdio.
Move of_mdio.c from drivers/of to drivers/net/mdio
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When packets are received on the error queue, this function under
net_ratelimit():
netif_err(priv, hw, net_dev, "Err FD status = 0x%08x\n");
does not get printed. Instead we only see:
[ 3658.845592] net_ratelimit: 244 callbacks suppressed
[ 3663.969535] net_ratelimit: 230 callbacks suppressed
[ 3669.085478] net_ratelimit: 228 callbacks suppressed
Enabling NETIF_MSG_HW fixes this issue, and we can see some information
about the frame descriptors of packets.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Factor out handling the private packet/byte counters to new
functions rtl_get_priv_stats() and rtl_inc_priv_stats().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Obviously this driver version doesn't make sense. Go with the default
and let ethtool display the kernel version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make use of the new struct_size() helper instead of the offsetof() idiom.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAl9/hIITHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqSUNB/9NiVYEPFF2mkNKzHAkhOssFF2NIzo8
0LBsV/YbOFqxSW0nYg0BB2nIdfIIdR+yqBW3ishbvizAWUOzSVvGD03oG0pZkKaZ
eMhh+OQ5fBjIjkNYXHC870uUZyJ7FzcyFLpeNoJfrGVuAtTpQts2TwWwevArPhfk
4XswX7DQ5npLwTGWBIvL8a6zYAmjEtT5Fnds0oeGeLfepWePG0ih/uxLN65JTrTU
uHt5gSgJLflXF+swErnLosMr1ADy2I+Zsg3XlYp89A9xLy5IEh0vyQPxEl69Wu1x
gQgO7L675YRwO9EyVkIfkYUzd/ot3o+virHTN470unu5QCb6O+04nof1
=omsQ
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.9-20201008' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
====================
linux-can-fixes-for-5.9-20201008
The first patch is by Lucas Stach and fixes m_can driver by removing an
erroneous call to m_can_class_suspend() in runtime suspend. Which causes the
pinctrl state to get stuck on the "sleep" state, which breaks all CAN
functionality on SoCs where this state is defined.
The last two patches target the j1939 protocol: Cong Wang fixes a syzbot
finding of an uninitialized variable in the j1939 transport protocol. I
contribute a patch, that fixes the initialization of a same uninitialized
variable in a different function.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fourth and last set of patches for v5.10. Most of these are iwlwifi
patches, but few small fixes to other drivers as well.
Major changes:
iwlwifi
* PNVM support (platform-specific phy config data)
* bump the FW API support to 59
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfgIilAAoJEG4XJFUm622b/MoH+wfx+CnW2J49uRAlAiAyJ8oW
pBKvJF1b6kbLeWurQPQH6ecmmYy0H/Cr8Zy4IW+YP7XN5PbSpDe4HXH6GkLP41fv
73kd0qHPFp42dmArImCqd8+9vAuh6C/taHSPV8klGaSfATUvvDIwgPrxGJnaGvwm
3E+SOnGcvqRV1fkBi7CArdIa1DzZwyu9q9zvQKbElmL7lX/r5kAzkHZqlMr3ZyjO
Gvuzvz9FIKvkU81IxtR8VXJh5RQ9WCXvsa00ZoP489jUz/lUoC2Rjofn55BcdAIh
1V4N7yOM2KFjDo3RWGZo+fqNo6LXREMyVQetmXCWPzFzCkMTN5FCWuj182dnYIM=
=9NpN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-10-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
Fourth and last set of patches for v5.10. Most of these are iwlwifi
patches, but few small fixes to other drivers as well.
Major changes:
iwlwifi
* PNVM support (platform-specific phy config data)
* bump the FW API support to 59
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAl9+MLsTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqScfCACBLbt8heMyVQQYd130/oIAvQ2o8Bjf
DPa36CVMYOGH1KOCnEyuc+oKsXeJfy33Faxe3+s7q2aMkddH7zhHQNiohPgwWAsM
AuAjRgbAVkDd9BTAbOS/cujftZBBccGRUuusbCg7lsBdwhGQbCggfYbOmGt2B8Gv
Wt3s2td8i90WutFb3UN3ec5N44jTn+WQvuOjX0Dzt/qi3r5qyC5JvcdkW3LAfxEG
X7bJ6cf8HRgUyPAALJGdoWdKT+ImmFbUJc8WuX9PdlYzxR+FyPKQgxD187ARTeLA
OqQSMHi4jRNywei0WUg5YoR0qPAHWKOLIMBK45TWNfa0p2+JzRbxTf3o
=7UL+
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.10-20201007' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
linux-can-next-for-5.10-20201007
The first 3 patches are by me and fix several warnings found
when compiling the kernel with W=1.
Lukas Bulwahn's patch adjusts the MAINTAINERS file, to accommodate
the renaming of the mcp251xfd driver.
Vincent Mailhol contributes 3 patches for the CAN networking layer.
First error queue support is added the the CAN RAW protocol.
The second patch converts the get_can_dlc() and get_canfd_dlc()
in-Kernel-only macros from using __u8 to u8.
The third patch adds a helper function to calculate the length of
one bit in in multiple of time quanta.
Oliver Hartkopp's patch add support for the ISO 15765-2:2016
transport protocol to the CAN stack.
Three patches by Lad Prabhakar add documentation for various
new rcar controllers to the device tree bindings of the rcar_can
and rcan_canfd driver.
Michael Walle's patch adds various processors to the flexcan
driver binding documentation.
The next two patches are by me and target the flexcan driver aswell.
The remove the ack_grp and ack_bit from the fsl,stop-mode DT property
and the driver, as they are not used anymore. As these are the last
two arguments this change will not break existing device trees.
The last three patches are by Srinivas Neeli and target
the xilinx_can driver.
The first one increases the lower limit for the bit rate
prescaler to 2, the other two fix sparse and coverity findings.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When processing a system suspend request we suspend modem endpoints
if they are enabled, and call ipa_cmd_tag_process() (which issues
IPA commands) to ensure the IPA pipeline is cleared. It is an error
to attempt to issue an IPA command before setup is complete, so this
is clearly a bug. But we also shouldn't suspend or resume any
endpoints that have not been set up.
Have ipa_endpoint_suspend() and ipa_endpoint_resume() immediately
return if setup hasn't completed, to avoid any attempt to configure
endpoints or issue IPA commands in that case.
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A subsequent addition of an IP4 or IP6 rule after other rules would
overwrite any existing TCAM entries of related L4 protocols(ex: tcp4 or
udp6). This was due to the mask including too many TCAM entries. Add new
packet type masks with bits properly excluded so rules are not overwritten.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pointers should be casted to unsigned long to avoid
-Wpointer-to-int-cast warnings:
drivers/net/ethernet/intel/ice/ice_flow.h:197:33: warning:
cast from pointer to integer of different size
drivers/net/ethernet/intel/ice/ice_flow.h:198:32: warning:
cast to pointer from integer of different size
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While debugging a recent failure to update the flash of an ice device,
I found it helpful to add additional logging which helped determine the
root cause of the problem being a timeout issue.
Add some extra dev_dbg() logging messages which can be enabled using the
dynamic debug facility, including one for ice_aq_wait_for_event that
will use jiffies to capture a rough estimate of how long we waited for
the completion of a firmware command.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the devlink_port structure is stored within the ice_pf. This
made sense because we create a single devlink_port for each PF. This
setup does not mesh with the abstractions in the driver very well, and
led to a flow where we accidentally call devlink_port_unregister twice
during error cleanup.
In particular, if devlink_port_register or devlink_port_unregister are
called twice, this leads to a kernel panic. This appears to occur during
some possible flows while cleaning up from a failure during driver
probe.
If register_netdev fails, then we will call devlink_port_unregister in
ice_cfg_netdev as it cleans up. Later, we again call
devlink_port_unregister since we assume that we must cleanup the port
that is associated with the PF structure.
This occurs because we cleanup the devlink_port for the main PF even
though it was not allocated. We allocated the port within a per-VSI
function for managing the main netdev, but did not release the port when
cleaning up that VSI, the allocation and destruction are not aligned.
Instead of attempting to manage the devlink_port as part of the PF
structure, manage it as part of the PF VSI. Doing this has advantages,
as we can match the de-allocation of the devlink_port with the
unregister_netdev associated with the main PF VSI.
Moving the port to the VSI is preferable as it paves the way for
handling devlink ports allocated for other purposes such as SR-IOV VFs.
Since we're changing up how we allocate the devlink_port, also change
the indexing. Originally, we indexed the port using the PF id number.
This came from an old goal of sharing a devlink for each physical
function. Managing devlink instances across multiple function drivers is
not workable. Instead, lets set the port number to the logical port
number returned by firmware and set the index using the VSI index
(sometimes referred to as VSI handle).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add "fw.app.bundle_id" to display the DDP Track ID of the active DDP
package. This id is similar to "fw.bundle_id" and is a unique identifier
for the DDP package that is loaded in the device. Each new DDP has
a unique Track ID generated for it, and the ID can be used to identify
and track the DDP package.
Add documentation for the new devlink info version.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ice_info_get_dsn always returns 0, so just make it void.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A new test in checkpatch detects repeated words; cleanup all pre-existing
occurrences of those now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Co-developed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use %*phD format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the KSZ9563 3-Port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9563 supports both SPI (already in) and I2C. The
ksz9563 is already in the device tree binding documentation.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for devlink reload action fw_activate with reload limit
no_reset which does firmware live patching, updating the firmware image
without reset, no downtime and no configuration lose. The driver checks
if the firmware is capable of handling the pending firmware changes as a
live patch. If it is then it triggers firmware live patching flow.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Firmware live patch event notifies the driver that the firmware was just
updated using live patch. In such case the driver should not reload or
re-initiate entities, part to updating the firmware version and
re-initiate the firmware tracer which can be updated by live patch with
new strings database to help debugging an issue.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The enable_remote_dev_reset devlink param flags that the host admin
allows resets by other hosts. In case it is cleared mlx5 host PF driver
will send NACK on pci sync for firmware update reset request and the
command will fail.
By default enable_remote_dev_reset parameter is true, so pci sync for
firmware update reset is enabled.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for devlink reload action fw_activate. To activate firmware
image the mlx5 driver resets the firmware and reloads it from flash. If
a new image was stored on flash it will be loaded. Once this reload
command is executed the driver initiates fw sync reset flow, where the
firmware synchronizes all PFs on coming reset and driver reload.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If firmware sends sync_reset_abort to driver the driver should clear the
reset requested mode as reset is not expected any more.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On sync_reset_now event the driver does reload and PCI link toggle to
activate firmware upgrade reset. When the firmware sends this event it
syncs the event on all PFs, so all PFs will do PCI link toggle at once.
To do PCI link toggle, the driver ensures that no other device ID under
the same bridge by checking that all the PF functions under the same PCI
bridge have same device ID. If no other device it uses PCI bridge link
control to turn link down and up.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Once the driver gets sync_reset_request from firmware it prepares for the
coming reset and sends acknowledge.
After getting this event the driver expects device reset, either it will
trigger PCI reset on sync_reset_now event or such PCI reset will be
triggered by another PF of the same device. So it moves to reset
requested mode and if it gets PCI reset triggered by the other PF it
detect the reset and reloads.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set capability to notify the firmware that this host driver is capable
of handling pci sync for firmware update events.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add functions to query and set the MFRL reset options supported by
firmware.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add reload limit to demand restrictions on reload actions.
Reload limits supported:
no_reset: No reset allowed, no down time allowed, no link flap and no
configuration is lost.
By default reload limit is unspecified and so no constraints on reload
actions are required.
Some combinations of action and limit are invalid. For example, driver
can not reinitialize its entities without any downtime.
The no_reset reload limit will have usecase in this patchset to
implement restricted fw_activate on mlx5.
Have the uapi parameter of reload limit ready for future support of
multiselection.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add devlink reload action to allow the user to request a specific reload
action. The action parameter is optional, if not specified then devlink
driver re-init action is used (backward compatible).
Note that when required to do firmware activation some drivers may need
to reload the driver. On the other hand some drivers may need to reset
the firmware to reinitialize the driver entities. Therefore, the devlink
reload command returns the actions which were actually performed.
Reload actions supported are:
driver_reinit: driver entities re-initialization, applying devlink-param
and devlink-resource values.
fw_activate: firmware activate.
command examples:
$devlink dev reload pci/0000:82:00.0 action driver_reinit
reload_actions_performed:
driver_reinit
$devlink dev reload pci/0000:82:00.0 action fw_activate
reload_actions_performed:
driver_reinit fw_activate
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phy_reset_after_clk_enable() does a PHY reset, which means the PHY
loses its register settings. The fec_enet_mii_probe() starts the PHY
and does the necessary calls to configure the PHY via PHY framework,
and loads the correct register settings into the PHY. Therefore,
fec_enet_mii_probe() should be called only after the PHY has been
reset, not before as it is now.
Fixes: 1b0a83ac04 ("net: fec: add phy_reset_after_clk_enable() support")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Without these definitions, the driver will crash in:
mscc_ocelot_probe
-> ocelot_init
-> ocelot_vcap_init
-> __ocelot_target_read_ix
I missed this because I did not have the VSC7514 hardware to test, only
the VSC9959 and VSC9953, and the probing part is different.
Fixes: e3aea296d8 ("net: mscc: ocelot: add definitions for VCAP ES0 keys, actions and target")
Fixes: a61e365d7c ("net: mscc: ocelot: add definitions for VCAP IS1 keys, actions and target")
Reported-by: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add usb ids of the Cellient MPL200 card.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
De-referencing skb after call to gro_cells_receive() is not allowed.
We need to fetch skb->len earlier.
Fixes: 5491e7c6b1 ("macsec: enable GRO and RPS on macsec devices")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some firmware files trigger a PHY soft reset and don't wait for it to
be finished. PHY register writes directly after applying the firmware
may fail or provide unexpected results therefore. Fix this by waiting
for bit BMCR_RESET to be cleared after applying firmware.
There's nothing wrong with the referenced change, it's just that the
fix will apply cleanly only after this change.
Fixes: 89fbd26cca ("r8169: fix firmware not resetting tp->ocp_base")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver looks for a PNVM file that contains FW configuration data
for each different HW combination. The FW requests the data for a
certain SKU_ID and the driver tries to find it in the PNVM file.
Read the file, parse its contents and send it to the trans.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.826bc607e57a.I1d93dd6e6651586878db57fac3e7c3f09d742c42@changeid
When adding support for version 3 of the GEO_TX_POWER_LIMIT command,
the table argument of iwl_sar_geo_init was changed from a pointer a 1d
array of now-removed iwl_per_chain_offset_group_v1 to a pointer to a 2d
array of iwl_per_chain_offset (iwl_per_chain_offset_group_v1 was a
struct containing 2 copies of iwl_per_chain_offset).
So even for version 2 where the second dimension is of length 2, which
means that the underlying memory layout of the array didn't change, this
requires a small change in the way we loop over it, and this was missed.
Additionally, for the case of version 3 where the second dimension is now
3, in order to fill the first two elements of each row correctly (lb and
hb), iwl_sar_geo_init must get the true number of bands supported.
But because we don't yet store any values for the 3rd (uhb) band, skip
that band.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.73605b6e0548.Id0ec98333277ff9e017e3938ae413b34acc68947@changeid
iwl_mvm_wowlan_program_keys is now setting data directly in
the KEK_KCK command, and the memset is clearing this later,
causing the data to be incomplete.
Just remove the memory clearing, the structure is local and
cleared in the declaration.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.0f355b4578c5.Ifbb76a2814925f215a2c889c1792d46d5bd66ab8@changeid
We introduced a new flow to remove an on-going CSA but we
assumed the firwmare understands the
CHANNEL_SWITCH_TIME_EVENT_CMD. This is not true for 7265 and down.
Don't send this command for those devices, but rather use the older
command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.2574e3e47927.Ic0c56411da1096e9a45ee5c3383edf777c5baca0@changeid
We were using a very high latency for all 9560 devices so they all
would have time to stabilize. But this causes the system to be
slighly slower, so we can use the best values for each device.
This requires a new trans cfg struct for devices with longer latency
and some adjustments to the other structs.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.34392f98fdb1.I3d3db14f6d1a8ecc547ca6afce8488816bd26081@changeid
ADD_STA_CMD_API_S ver 12 was added in order to properly support
auxiliary activities in CDB NICs. In the new version we don't need
to allocate an aux station at initialization, instead we add an
aux station only when an auxiliary activity that requires a dedicated Tx
queue is needed. For now the only case we need this kind of activity is
when using hot spot 2.0
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.700e6e2e3077.Icdd807b6a3ad3fed806449ea0a13f856aa20e632@changeid
As part of changes made to properly support auxiliary activities in CDB
NICs, an aux sta will be added when using hot spot 2.0 and will need
to be removed when roc flow is done.
In order to do so, prepare the roc_done_wk to work synchronously as the
rm_aux_sta is a SYNC command.
Since now all of th iwl_mvm_flush_sta function are using it sync,
removed the flag argument from the function.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.71b441c8b682.Ia1d216cb680308b91d6da9f73e23ae9f4baac79f@changeid
The FW relies on the re-enablement of the TX in order to know
it can exit quiet mode. Currently in case of CSA with quiet mode,
the quiet mode is never cancelled, resulting in a complete traffic
hang.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.fee389c83ded.I09550fdadb61f899242d7e7b7578672372e2b7fe@changeid
If we have only a single RX queue, such as when MSI-X is not
available, we should not send the RFH_QUEUEU_CONFIG_CMD, because our
only queue is the same as the command queue and will be configured as
part of the context info. Our code was actually trying to send the
command with 0 queues, which caused UMAC assert 0x1D04.
Fix that by not sending the command when we have a single queue.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.c35eeb3299f8.I08f79a6ebe150a7d180b7005b24504bfdba6d8b5@changeid
The legacy_httxpowerdiff in rtl8192se is pretty much the same as
the legacy_ht_txpowerdiff for other chips. Use the same name to
keep the consistency.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201006035928.5566-1-chiu@endlessm.com
clang static analysis reports this problem:
sdio.c:2403:3: warning: Attempt to free released memory
kfree(card->mpa_rx.buf);
^~~~~~~~~~~~~~~~~~~~~~~
When mwifiex_init_sdio() fails in its first call to
mwifiex_alloc_sdio_mpa_buffer, it falls back to calling it
again. If the second alloc of mpa_tx.buf fails, the error
handler will try to free the old, previously freed mpa_rx.buf.
Reviewing the code, it looks like a second double free would
happen with mwifiex_cleanup_sdio().
So set both pointers to NULL when they are freed.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201004131931.29782-1-trix@redhat.com
In ath11k_mac_setup_iface_combinations(), if memory cannot be assigned
for the variable limits, then the memory assigned to combinations will
be leaked. Fix this.
Addresses-Coverity-ID: 1497534 ("Resource leaks")
Fixes: 2626c26970 ("ath11k: add interface_modes to hw_params")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201004100218.311653-2-alex.dewar90@gmail.com
Also demote a non-conforming kernel-doc function header.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/iwl-drv.c:124: warning: Function parameter or member 'dbgfs_drv' not described in 'iwl_drv'
drivers/net/wireless/intel/iwlwifi/iwl-drv.c:124: warning: Function parameter or member 'dbgfs_trans' not described in 'iwl_drv'
drivers/net/wireless/intel/iwlwifi/iwl-drv.c:124: warning: Function parameter or member 'dbgfs_op_mode' not described in 'iwl_drv'
drivers/net/wireless/intel/iwlwifi/iwl-drv.c:1329: warning: Function parameter or member 'ucode_raw' not described in 'iwl_req_fw_callback'
drivers/net/wireless/intel/iwlwifi/iwl-drv.c:1329: warning: Function parameter or member 'context' not described in 'iwl_req_fw_callback'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-16-lee.jones@linaro.org
Kerneldoc expects attributes/parameters to be in '@*.: ' format and
gets confused if the variable does not follow the type/attribute
definitions.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/devices.c:66: warning: Function parameter or member 'priv' not described in 'iwl_beacon_time_mask_low'
drivers/net/wireless/intel/iwlwifi/dvm/devices.c:66: warning: Function parameter or member 'tsf_bits' not described in 'iwl_beacon_time_mask_low'
drivers/net/wireless/intel/iwlwifi/dvm/devices.c:77: warning: Function parameter or member 'priv' not described in 'iwl_beacon_time_mask_high'
drivers/net/wireless/intel/iwlwifi/dvm/devices.c:77: warning: Function parameter or member 'tsf_bits' not described in 'iwl_beacon_time_mask_high'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-15-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1379: warning: Function parameter or member 'rate_n_flags' not described in 'iwl_mvm_hwrate_to_tx_status'
drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1379: warning: Function parameter or member 'info' not described in 'iwl_mvm_hwrate_to_tx_status'
drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1431: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_get_scd_ssn'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-14-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/rxon.c:695: warning: bad line:
drivers/net/wireless/intel/iwlwifi/dvm/rxon.c:701: warning: Function parameter or member 'priv' not described in 'iwl_set_rxon_channel'
drivers/net/wireless/intel/iwlwifi/dvm/rxon.c:701: warning: Function parameter or member 'ctx' not described in 'iwl_set_rxon_channel'
drivers/net/wireless/intel/iwlwifi/dvm/rxon.c:839: warning: Function parameter or member 'ctx' not described in 'iwl_full_rxon_required'
drivers/net/wireless/intel/iwlwifi/dvm/rxon.c:1029: warning: Function parameter or member 'priv' not described in 'iwlagn_commit_rxon'
drivers/net/wireless/intel/iwlwifi/dvm/rxon.c:1029: warning: Function parameter or member 'ctx' not described in 'iwlagn_commit_rxon'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-13-lee.jones@linaro.org
2 of which do not attempt to document their parameters, 1 does a poor job.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:193: warning: Function parameter or member 'priv' not described in 'iwl_scan_cancel'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:205: warning: Function parameter or member 'priv' not described in 'iwl_scan_cancel_timeout'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:570: warning: Function parameter or member 'frame' not described in 'iwl_fill_probe_req'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:570: warning: Function parameter or member 'ta' not described in 'iwl_fill_probe_req'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:570: warning: Function parameter or member 'ies' not described in 'iwl_fill_probe_req'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:570: warning: Function parameter or member 'ie_len' not described in 'iwl_fill_probe_req'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:570: warning: Function parameter or member 'ssid' not described in 'iwl_fill_probe_req'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:570: warning: Function parameter or member 'ssid_len' not described in 'iwl_fill_probe_req'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:570: warning: Function parameter or member 'left' not described in 'iwl_fill_probe_req'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-12-lee.jones@linaro.org
Fix misnamed, and missing descriptions likely due to doc-rot.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:669: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:669: warning: Function parameter or member 'lq' not described in 'iwl_mvm_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:669: warning: Excess function parameter 'sync' description in 'iwl_mvm_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_update_smps'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Function parameter or member 'vif' not described in 'iwl_mvm_update_smps'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Function parameter or member 'smps_request' not described in 'iwl_mvm_update_smps'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Excess function parameter 'smps_requests' description in 'iwl_mvm_update_smps'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-11-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/rx.c:145: warning: Function parameter or member 'priv' not described in 'iwlagn_good_plcp_health'
drivers/net/wireless/intel/iwlwifi/dvm/rx.c:145: warning: Function parameter or member 'cur_ofdm' not described in 'iwlagn_good_plcp_health'
drivers/net/wireless/intel/iwlwifi/dvm/rx.c:145: warning: Function parameter or member 'cur_ofdm_ht' not described in 'iwlagn_good_plcp_health'
drivers/net/wireless/intel/iwlwifi/dvm/rx.c:145: warning: Function parameter or member 'msecs' not described in 'iwlagn_good_plcp_health'
drivers/net/wireless/intel/iwlwifi/dvm/rx.c:939: warning: Function parameter or member 'priv' not described in 'iwl_setup_rx_handlers'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-10-lee.jones@linaro.org
Looks as if it's never been used.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/ops.c:466:36: warning: ‘iwl_mvm_debug_names’ defined but not used [-Wunused-const-variable=]
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-9-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:244: warning: Function parameter or member 'priv' not described in 'iwl_prep_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:244: warning: Function parameter or member 'ctx' not described in 'iwl_prep_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:244: warning: Function parameter or member 'addr' not described in 'iwl_prep_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:244: warning: Function parameter or member 'is_ap' not described in 'iwl_prep_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:244: warning: Function parameter or member 'sta' not described in 'iwl_prep_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:332: warning: Function parameter or member 'priv' not described in 'iwl_add_station_common'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:332: warning: Function parameter or member 'ctx' not described in 'iwl_add_station_common'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:332: warning: Function parameter or member 'addr' not described in 'iwl_add_station_common'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:332: warning: Function parameter or member 'is_ap' not described in 'iwl_add_station_common'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:332: warning: Function parameter or member 'sta' not described in 'iwl_add_station_common'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:332: warning: Function parameter or member 'sta_id_r' not described in 'iwl_add_station_common'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:390: warning: Function parameter or member 'priv' not described in 'iwl_sta_ucode_deactivate'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:390: warning: Function parameter or member 'sta_id' not described in 'iwl_sta_ucode_deactivate'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:459: warning: Function parameter or member 'priv' not described in 'iwl_remove_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:459: warning: Function parameter or member 'sta_id' not described in 'iwl_remove_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:459: warning: Function parameter or member 'addr' not described in 'iwl_remove_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:614: warning: Function parameter or member 'priv' not described in 'iwl_clear_ucode_stations'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:614: warning: Function parameter or member 'ctx' not described in 'iwl_clear_ucode_stations'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:648: warning: Function parameter or member 'priv' not described in 'iwl_restore_stations'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:648: warning: Function parameter or member 'ctx' not described in 'iwl_restore_stations'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:790: warning: Function parameter or member 'priv' not described in 'is_lq_table_valid'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:790: warning: Function parameter or member 'ctx' not described in 'is_lq_table_valid'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:790: warning: Function parameter or member 'lq' not described in 'is_lq_table_valid'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:822: warning: Function parameter or member 'priv' not described in 'iwl_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:822: warning: Function parameter or member 'ctx' not described in 'iwl_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:822: warning: Function parameter or member 'lq' not described in 'iwl_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:822: warning: Function parameter or member 'flags' not described in 'iwl_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1270: warning: Function parameter or member 'priv' not described in 'iwlagn_alloc_bcast_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1270: warning: Function parameter or member 'ctx' not described in 'iwlagn_alloc_bcast_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1309: warning: Function parameter or member 'priv' not described in 'iwl_update_bcast_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1309: warning: Function parameter or member 'ctx' not described in 'iwl_update_bcast_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1348: warning: Function parameter or member 'priv' not described in 'iwl_sta_tx_modify_enable_tid'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1348: warning: Function parameter or member 'sta_id' not described in 'iwl_sta_tx_modify_enable_tid'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1348: warning: Function parameter or member 'tid' not described in 'iwl_sta_tx_modify_enable_tid'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-8-lee.jones@linaro.org
This is the only use of kerneldoc in the sourcefile and no
descriptions are provided.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/calib.c:770: warning: Function parameter or member 'priv' not described in 'iwl_find_disconn_antenna'
drivers/net/wireless/intel/iwlwifi/dvm/calib.c:770: warning: Function parameter or member 'average_sig' not described in 'iwl_find_disconn_antenna'
drivers/net/wireless/intel/iwlwifi/dvm/calib.c:770: warning: Function parameter or member 'data' not described in 'iwl_find_disconn_antenna'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-6-lee.jones@linaro.org
Neither of these headers attempt to document any function parameters.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/lib.c:121: warning: Function parameter or member 'priv' not described in 'iwlagn_txfifo_flush'
drivers/net/wireless/intel/iwlwifi/dvm/lib.c:121: warning: Function parameter or member 'scd_q_msk' not described in 'iwlagn_txfifo_flush'
drivers/net/wireless/intel/iwlwifi/dvm/lib.c:779: warning: Function parameter or member 'priv' not described in 'iwlagn_set_rxon_chain'
drivers/net/wireless/intel/iwlwifi/dvm/lib.c:779: warning: Function parameter or member 'ctx' not described in 'iwlagn_set_rxon_chain'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-5-lee.jones@linaro.org
None of these headers attempt to document any function parameters.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/tx.c:811: warning: Function parameter or member 'priv' not described in 'iwlagn_hwrate_to_tx_control'
drivers/net/wireless/intel/iwlwifi/dvm/tx.c:811: warning: Function parameter or member 'rate_n_flags' not described in 'iwlagn_hwrate_to_tx_control'
drivers/net/wireless/intel/iwlwifi/dvm/tx.c:811: warning: Function parameter or member 'info' not described in 'iwlagn_hwrate_to_tx_control'
drivers/net/wireless/intel/iwlwifi/dvm/tx.c:1267: warning: Function parameter or member 'priv' not described in 'iwlagn_rx_reply_compressed_ba'
drivers/net/wireless/intel/iwlwifi/dvm/tx.c:1267: warning: Function parameter or member 'rxb' not described in 'iwlagn_rx_reply_compressed_ba'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-4-lee.jones@linaro.org
None of these headers attempt to document any function parameters.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:165: warning: cannot understand function prototype: 'const u16 expected_tpt_legacy[IWL_RATE_COUNT] = '
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:329: warning: Function parameter or member 'priv' not described in 'rs_program_fix_rate'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:329: warning: Function parameter or member 'lq_sta' not described in 'rs_program_fix_rate'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:452: warning: Function parameter or member 'tbl' not described in 'rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:452: warning: Function parameter or member 'scale_index' not described in 'rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:452: warning: Function parameter or member 'attempts' not described in 'rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:452: warning: Function parameter or member 'successes' not described in 'rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:681: warning: Function parameter or member 'sta' not described in 'rs_use_green'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:702: warning: Function parameter or member 'lq_sta' not described in 'rs_get_supported_rates'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:702: warning: Function parameter or member 'hdr' not described in 'rs_get_supported_rates'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:702: warning: Function parameter or member 'rate_type' not described in 'rs_get_supported_rates'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:2628: warning: duplicate section name 'NOTE'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:2632: warning: Function parameter or member 'priv' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:2632: warning: Function parameter or member 'sta' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:2632: warning: Function parameter or member 'lq_sta' not described in 'rs_initialize_lq'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-3-lee.jones@linaro.org
None of these headers attempt to document any function parameters.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/main.c:388: warning: Function parameter or member 't' not described in 'iwl_bg_statistics_periodic'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:545: warning: Function parameter or member 't' not described in 'iwl_bg_ucode_trace'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:771: warning: Function parameter or member 'priv' not described in 'iwl_alive_start'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1692: warning: Function parameter or member 'priv' not described in 'iwl_print_event_log'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1692: warning: Function parameter or member 'start_idx' not described in 'iwl_print_event_log'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1692: warning: Function parameter or member 'num_events' not described in 'iwl_print_event_log'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1692: warning: Function parameter or member 'mode' not described in 'iwl_print_event_log'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1692: warning: Function parameter or member 'pos' not described in 'iwl_print_event_log'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1692: warning: Function parameter or member 'buf' not described in 'iwl_print_event_log'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1692: warning: Function parameter or member 'bufsz' not described in 'iwl_print_event_log'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'priv' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'capacity' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'num_wraps' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'next_entry' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'size' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'mode' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'pos' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'buf' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'bufsz' not described in 'iwl_print_last_event_logs'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-2-lee.jones@linaro.org
Some variables with incorrect type were passed to "of_property_read_u32"
API, "of_property_read_u32" API was expecting an "u32 *" but the formal
parameter that was passed was of type "int *". Fixed the issue by
changing the variable types from "int" to "u32" and initialized with a
default value. Fixed sparse warning.
Addresses-Coverity: "incompatible_param"
Addresses-Coverity: "UNINIT(Using uninitialized value)"
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/0651544d22f3c25893ca9d445b14823f0dfddfc8.1600073396.git.michal.simek@xilinx.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit:
048e3a34a2 can: flexcan: poll MCR_LPM_ACK instead of GPR ACK for stop mode acknowledgment
the driver polls the IP core's internal bit MCR[LPM_ACK] as stop mode
acknowledge and not the acknowledgment on chip level.
This means the 4th and 5th value of the property "fsl,stop-mode" isn't used
anymore. This patch removes the used "ack_gpr" and "ack_bit" from the driver.
Link: http://lore.kernel.org/r/20201006203748.1750156-15-mkl@pengutronix.de
Fixes: 048e3a34a2 ("can: flexcan: poll MCR_LPM_ACK instead of GPR ACK for stop mode acknowledgment")
Cc: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rename macro CAN_CALC_SYNC_SEG to CAN_SYNC_SEG and make it available
through include/linux/can/dev.h
Add an helper function can_bit_time() which returns the duration (in
time quanta) of one CAN bit.
Rationale for this patch: the sync segment and the bit time are two
concepts which are defined in the CAN ISO standard. Device drivers for
CAN might need those.
Please refer to ISO 11898-1:2015, section 11.3.1.1 "Bit time" for
additional information.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20201002154219.4887-6-mailhol.vincent@wanadoo.fr
[mkl: Let can_bit_time() return an unsinged int, make argument const]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
0704c57436 can: m_can_platform: remove unnecessary m_can_class_resume() call
removed the m_can_class_resume() call in the runtime resume path to get
rid of a infinite recursion, so the runtime resume now only handles the device
clocks.
Unfortunately it did not remove the complementary m_can_class_suspend() call in
the runtime suspend function, so those paths are now unbalanced, which causes
the pinctrl state to get stuck on the "sleep" state, which breaks all CAN
functionality on SoCs where this state is defined. Remove the
m_can_class_suspend() call to fix this.
Fixes: 0704c57436 can: m_can_platform: remove unnecessary m_can_class_resume() call
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20200811081545.19921-1-l.stach@pengutronix.de
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch marks the arrays reg_map_c_can and reg_map_d_can as __maybe_unused,
as they are indeed unused in the c_can driver. This warning shows up, when
compiling the kernel with "W=1":
drivers/net/can/c_can/c_can.c:45:
drivers/net/can/c_can/c_can.h:124:18: warning: ‘reg_map_d_can’ defined but not used [-Wunused-const-variable=]
drivers/net/can/c_can/c_can.h:84:18: warning: ‘reg_map_c_can’ defined but not used [-Wunused-const-variable=]
Link: http://lore.kernel.org/r/20201006203748.1750156-4-mkl@pengutronix.de
Fixes: 33f8100977 ("can: c_can: Move overlay structure to array with offset as index")
Fixes: 69927fccd9 ("can: c_can: Add support for Bosch D_CAN controller")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the following warning when building the kernel with "W=1":
warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Link: http://lore.kernel.org/r/20201006203748.1750156-3-mkl@pengutronix.de
Fixes: 03fd3cf5a1 ("can: add driver for Softing card")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
use new helper for netstats settings
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mediadetect is another name for the EDPD (energy detect power down).
This feature allows device to save extra power when no link is available.
PHY goes into the extreme power saving mode and only periodically wakes up
and checks for the link.
AQC devices has fixed check period of 6 seconds
The feature may increase linkup time.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY downshift allows phy to try renegotiate if link is unstable
and can carry higher speed.
AQC devices has integrated PHY which is controlled by MAC firmware.
Thus, driver defines new ethtool callbacks to implement phy tunables
via netdev.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When get_registers() fails in set_ethernet_addr(),the uninitialized
value of node_id gets copied over as the address.
So, check the return value of get_registers().
If get_registers() executed successfully (i.e., it returns
sizeof(node_id)), copy over the MAC address using ether_addr_copy()
(instead of using memcpy()).
Else, if get_registers() failed instead, a randomly generated MAC
address is set as the MAC address instead.
Reported-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Tested-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an upper bound to the value that a watermark may hold. That
upper bound is not immediately obvious during configuration, and it
might be possible to have accidental truncation.
Actually this has happened already, add a warning to prevent it from
happening again.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tail dropping is enabled for a port when:
1. A source port consumes more packet buffers than the watermark encoded
in SYS:PORT:ATOP_CFG.ATOP.
AND
2. Total memory use exceeds the consumption watermark encoded in
SYS:PAUSE_CFG:ATOP_TOT_CFG.
The unit of these watermarks is a 60 byte memory cell. That unit is
programmed properly into ATOP_TOT_CFG, but not into ATOP. Actually when
written into ATOP, it would get truncated and wrap around.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert m88e1318_get_wol() to use the well implemented phy_read_paged()
instead of open coding it.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
(the DSA framework just checks for the presence of the .port_vlan_add
and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime
Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.
So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.
Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Keep the code for the normal (non-error) flow at the lowest
indentation level. And use "goto drop" for all error handling.
2. Replace code that pads short Ethernet frames with a "__skb_pad" call.
3. Change "dev_kfree_skb" to "kfree_skb" in error handling code.
"kfree_skb" is the correct function to call when dropping an skb due to
an error. "dev_kfree_skb", which is an alias of "consume_skb", is for
dropping skbs normally (not due to an error).
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang static analysis reports this problem:
drivers/net/ethernet/marvell/mvneta.c:3465:2: warning:
Attempt to free released memory
kfree(txq->buf);
^~~~~~~~~~~~~~~
When mvneta_txq_sw_init() fails to alloc txq->tso_hdrs,
it frees without poisoning txq->buf. The error is caught
in the mvneta_setup_txqs() caller which handles the error
by cleaning up all of the txqs with a call to
mvneta_txq_sw_deinit which also frees txq->buf.
Since mvneta_txq_sw_deinit is a general cleaner, all of the
partial cleaning in mvneta_txq_sw_deinit()'s error handling
is not needed.
Fixes: 2adb719d74 ("net: mvneta: Implement software TSO")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable "i" isn't initialized back correctly after the first loop
under the label inst_rollback gets executed.
The value of "i" is assigned to be option_count - 1, and the ensuing
loop (under alloc_rollback) begins by initializing i--.
Thus, the value of i when the loop begins execution will now become
i = option_count - 2.
Thus, when kfree(dst_opts[i]) is called in the second loop in this
order, (i.e., inst_rollback followed by alloc_rollback),
dst_optsp[option_count - 2] is the first element freed, and
dst_opts[option_count - 1] does not get freed, and thus, a memory
leak is caused.
This memory leak can be fixed, by assigning i = option_count (instead of
option_count - 1).
Fixes: 80f7c6683f ("team: add support for per-port options")
Reported-by: syzbot+69b804437cfec30deac3@syzkaller.appspotmail.com
Tested-by: syzbot+69b804437cfec30deac3@syzkaller.appspotmail.com
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver will schedule RX ring reset when we get a buffer
error in the RX completion record. These RX buffer errors can be due
to normal out-of-buffer conditions or a permanent error in the RX
ring. Because the driver cannot distinguish between these 2
conditions, we assume all these buffer errors require reset.
This is very disruptive when it is just a normal out-of-buffer
condition. Newer firmware will now monitor the rings for the permanent
failure and will send a notification to the driver when it happens.
This allows the driver to reset only when such a notification is
received. In environments where we have predominently out-of-buffer
conditions, we now can avoid these unnecessary resets.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is logic in the RX path to detect unexpected handles in the
RX completion. We'll print a warning and schedule a reset. The
next expected handle is then set to 0xffff which is guaranteed to
not match any valid handle. This will force all remaining packets in
the ring to be discarded before the reset. There can be hundreds of
these packets remaining in the ring and there is no need to print the
warnings for these forced errors.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a per ring rx_resets counter to count these RX resets.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some older chips, it is necessary to do a reset when we get buffer
errors associated with an RX ring. These buffer errors may become
frequent if the RX ring underruns under heavy traffic. The current
code does a global reset of all reasources when this happens. This
works but creates a big disruption of all rings when one RX ring is
having problem. This patch implements a localized RX ring reset of
just the RX ring having the issue. All other rings including all
TX rings will not be affected by this single RX ring reset.
Only the older chips prior to the P5 class supports this reset.
Because it is not a global reset, packets may still be arriving
while we are calling firmware to reset that ring. We need to be
sure that we don't post any buffers during this time while the
ring is undergoing reset. After firmware completes successfully,
the ring will be in the reset state with no buffers and we can start
filling it with new buffers and posting them.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_init_one_rx_ring() includes logic to initialize the BDs for one RX
ring and to allocate the buffers. Separate the allocation logic into a
new bnxt_alloc_one_rx_ring() function. The allocation function will be
used later to allocate new buffers for one specified RX ring when we
reset that RX ring.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_free_rx_skbs() frees all the allocated buffers and SKBs for
every RX ring. Refactor this function by calling a new function
bnxt_free_one_rx_ring_skbs() to free these buffers on one specified
RX ring at a time. This is preparation work for resetting one RX
ring during run-time.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware does not come out of reset, log FW health status info
to provide more information on firmware status.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NS3 SoC platforms require assistance from the OP-TEE to recover
firmware if a crash occurs while no driver is bound. The
CRASHED_NO_MASTER condition is recorded in the firmware status register
during the crash to indicate when driver intervension is needed to
coordinate a firmware reload. This condition is detected during early
driver initialization in order to effect a firmware fastboot on
supported platforms when necessary.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware now supports device independent discovery of the status
register location. This status register can provide more detailed
information about firmware errors, especially if problems occur
before the HWRM interface is functioning. Attempt to map this
register if it is present and report the firmware status on firmware
init failures.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocator for the firmware health structure conflates allocation
and capability checks, limiting the reusability of the code. This patch
separates out the capability check and disablement and improves the
warning message to better describe the consequences of an allocation
failure.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Main changes is to extend hwrm_nvm_get_dev_info_output() for stored
firmware versions and a new flag is added to fw_status_reg.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a devlink region to return the per port registers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a strictly cosmetic change that renames some macros in
sja1105_dynamic_config.c. They were copy-pasted in haste and this has
resulted in them having the driver prefix twice.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the comparisons of u16 integers value and sopass_val with
less than zero for error checking is always false because the values
are unsigned. Fix this by making these variables int. This does not
affect the shift and mask operations performed on these variables
Addresses-Coverity: ("Unsigned compared against zero")
Fixes: 49fc23018e ("net: phy: dp83869: support Wake on LAN")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix many (lots deleted here) build errors in hinic by selecting NET_DEVLINK.
ld: drivers/net/ethernet/huawei/hinic/hinic_hw_dev.o: in function `mgmt_watchdog_timeout_event_handler':
hinic_hw_dev.c:(.text+0x30a): undefined reference to `devlink_health_report'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_fw_reporter_dump':
hinic_devlink.c:(.text+0x1c): undefined reference to `devlink_fmsg_u32_pair_put'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_fw_reporter_dump':
hinic_devlink.c:(.text+0x126): undefined reference to `devlink_fmsg_binary_pair_put'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_hw_reporter_dump':
hinic_devlink.c:(.text+0x1ba): undefined reference to `devlink_fmsg_string_pair_put'
ld: hinic_devlink.c:(.text+0x227): undefined reference to `devlink_fmsg_u8_pair_put'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_alloc':
hinic_devlink.c:(.text+0xaee): undefined reference to `devlink_alloc'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_free':
hinic_devlink.c:(.text+0xb04): undefined reference to `devlink_free'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_register':
hinic_devlink.c:(.text+0xb26): undefined reference to `devlink_register'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_unregister':
hinic_devlink.c:(.text+0xb46): undefined reference to `devlink_unregister'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_health_reporters_create':
hinic_devlink.c:(.text+0xb75): undefined reference to `devlink_health_reporter_create'
ld: hinic_devlink.c:(.text+0xb95): undefined reference to `devlink_health_reporter_create'
ld: hinic_devlink.c:(.text+0xbac): undefined reference to `devlink_health_reporter_destroy'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_health_reporters_destroy':
Fixes: 51ba902a16 ("net-next/hinic: Initialize hw interface")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Bin Luo <luobin9@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Cc: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool manual stated that the tx-timer is the "the amount of time the
device should stay in idle mode prior to asserting its Tx LPI". The
previous implementation for "ethtool --set-eee tx-timer" sets the LPI TW
timer duration which is not correct. Hence, this patch fixes the
"ethtool --set-eee tx-timer" to configure the EEE LPI timer.
The LPI TW Timer will be using the defined default value instead of
"ethtool --set-eee tx-timer" which follows the EEE LS timer implementation.
Changelog V2
*Not removing/modifying the eee_timer.
*EEE LPI timer can be configured through ethtool and also the eee_timer
module param.
*EEE TW Timer will be configured with default value only, not able to be
configured through ethtool or module param. This follows the implementation
of the EEE LS Timer.
Fixes: d765955d2a ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bulk of the genetlink users can use smaller ops, move them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the new group of devlink traps - PARSER_ERROR_DROPS.
This consists of registering the array of parser error drops supported,
controlling their action through the .trap_group_action_set() callback
and reporting an erroneous skb received on the error queue
appropriately.
DPAA2 devices do not support controlling the action of independent
parser error traps, thus the .trap_action_set() callback just returns an
EOPNOTSUPP while .trap_group_action_set() actually notifies the hardware
what it should do with a frame marked as having a header error.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support in dpaa2-eth for devlink. For the moment, just
register the device with devlink, add the corresponding devlink port and
implement the .info_get() callback.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the new firmware image downladed for update is corrupted
or is a bad format, the download process will report a status
code specifically for that.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the lif's ident information for the uc and mc filter
counts rather than the ionic's version, to be sure
we're getting the info that is specific to this lif.
While we're thinking about it, add some missing error
checking where we get the lif's identity information.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
After we do a fw upgrade and refill the ionic->ident.dev, we
also need to update the other identity info. Since the lif
identity needs to be updated each time the ionic identity is
refreshed, we can pull it into ionic_identify().
The debugfs entry is moved so that it doesn't cause an
error message when the data is refreshed after the fw upgrade.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some time ago we short-circuited the queue disables on a timeout
error in order to not have to wait on every queue when we already
know it will time out. However, this meant that we're not
properly stopping all the interrupts and napi contexts. This
changes queue disable to always call ionic_qcq_disable() and to
give it an argument to know when to not do the adminq request.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a couple of error recovery paths that can come through
ionic_qcq_disable() without having set up the qcq, so we need
to make sure we have a valid qcq pointer before using it.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear our link check requested flag on an allocation error.
We end up dropping this link check request, but that should
be fine as our watchdog will come back a few seconds later
and request it again.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check through our work list for additional items. This normally
will only have one item, but occasionally may have another
job waiting. There really is no need reschedule ourself here.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The event notification queue is set up a little differently in the
NIC and so the notifyq q and cq descriptor structures need to be
contiguous, which got missed in an earlier patch that separated
out the q and cq descriptor allocations. That patch was aimed at
making the big tx and rx descriptor queue allocations easier to
manage - the notifyq is much smaller and doesn't need to be split.
This patch simply adds an if/else and slightly different code for
the notifyq descriptor allocation.
Fixes: ea5a8b09dc ("ionic: reduce contiguous memory allocation requirement")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl93ap4ACgkQSD+KveBX
+j5+eAf/dvxx+WyWr5pV3gxd0x7K/wV+F1JFVe99k8yH6kYbpo56U+oRQGP4kvnG
4Ggb/XE7hSahvReRVD5vn4LKk2RQ/GMWEurF/GQDPklaHZyZHtcI3+2C/azEHnf+
vGgbM1xDT0gNZoa+2pA7LBgruJF/k+gRbth6EHrjlcxqiqt2k4d5Hs0m/Xd5R0TC
D+Yks3uHAOrTiP2idOWNoWmd5AOmh802wX0w4iyKZ9ZfJGMN3t2AKyZDIhNfPyPf
avebIihkr5y5DsYGZE+HjZjK0+vXaKVAGgzDbeLZ2sPVdCJJAFRZptG6mPJ0d0N3
TPwcBZcs5BsJkEQ5XqBA0IwJjksVeA==
=421I
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
From: Saeed Mahameed <saeedm@nvidia.com>
====================
This series introduces some fixes to mlx5 driver.
v1->v2:
- Patch #1 Don't return while mutex is held. (Dave)
v2->v3:
- Drop patch #1, will consider a better approach (Jakub)
- use cpu_relax() instead of cond_resched() (Jakub)
- while(i--) to reveres a loop (Jakub)
- Drop old mellanox email sign-off and change the committer email
(Jakub)
Please pull and let me know if there is any problem.
For -stable v4.15
('net/mlx5e: Fix VLAN cleanup flow')
('net/mlx5e: Fix VLAN create flow')
For -stable v4.16
('net/mlx5: Fix request_irqs error flow')
For -stable v5.4
('net/mlx5e: Add resiliency in Striding RQ mode for packets larger than MTU')
('net/mlx5: Avoid possible free of command entry while timeout comp handler')
For -stable v5.7
('net/mlx5e: Fix return status when setting unsupported FEC mode')
For -stable v5.8
('net/mlx5e: Fix race condition on nhe->n pointer in neigh update')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Third set of patches for v5.10. Lots of iwlwifi patches this time, but
also few patches ath11k and of course smaller changes to other
drivers.
Major changes:
rtw88
* properly recover from firmware crashes on 8822c
* dump firmware crash log
iwlwifi
* protected Target Wake Time (TWT) implementation
* support disabling 5.8GHz channels via ACPI
* support VHT extended NSS capability
* enable Target Wake Time (TWT) by default
ath11k
* improvements to QCA6390 PCI support to make it more usable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfdzOKAAoJEG4XJFUm622bAxEH/2XBLA6RJ0/ypDYt32qj7q5/
hgV3tQkaCXTKnXo0O/6DtihdLD1gARg3Y8s1BY4wHzIZ57iR2LxKumzDS9f6S2oq
6/7OmBubZVzK8oii2bTleOu524Dfq6B019uOgtQJMAOT5S5X5uk25PDIfVCksv5m
ZKSNZINFqC2K9cQkXKP0cD0SSJDDHvcMjI8/nZ91mNLJ7StO3En4WDNMQJ7Jfa3M
VX18GI6XB/pqb18+QJwTXUKN4jODTYHH8zJ6LvYfDFq9vhN2GomdK5f3W9teIUwY
omQavKAFCPAhBja61IVGyo47ZB3MH57ECyuuBtAPv/ydcwAGXlJToHO8avM4K7I=
=WApP
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
Third set of patches for v5.10. Lots of iwlwifi patches this time, but
also few patches ath11k and of course smaller changes to other
drivers.
Major changes:
rtw88
* properly recover from firmware crashes on 8822c
* dump firmware crash log
iwlwifi
* protected Target Wake Time (TWT) implementation
* support disabling 5.8GHz channels via ACPI
* support VHT extended NSS capability
* enable Target Wake Time (TWT) by default
ath11k
* improvements to QCA6390 PCI support to make it more usable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Via the OCELOT_MASK_MODE_REDIRECT flag put in the IS2 action vector, it
is possible to replace previous forwarding decisions with the port mask
installed in this rule.
I have studied Table 54 "MASK_MODE and PORT_MASK Combinations" from the
VSC7514 documentation and it appears to behave sanely when this rule is
installed in either lookup 0 or 1. Namely, a redirect in lookup 1 will
overwrite the forwarding decision taken by any entry in lookup 0.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue which led to the introduction of this check was that MAC_ETYPE
rules, such as filters on dst_mac and src_mac, would only match non-IP
frames. There is a knob in VCAP_S2_CFG which forces all IP frames to be
treated as non-IP, which is what we're currently doing if the user
requested a dst_mac filter, in order to maintain sanity.
But that knob is actually per IS2 lookup. And the good thing with
exposing the lookups to the user via tc chains is that we're now able to
offload MAC_ETYPE keys to one lookup, and IP keys to the other lookup.
So let's do that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were installing TCAM rules with the LOOKUP field as unmasked, meaning
that all entries were matching on all lookups. Now that lookups are
exposed as individual chains, let's make the LOOKUP explicit when
offloading TCAM entries.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VCAP ES0 is an egress VCAP operating on all outgoing frames.
This patch added ES0 driver to support vlan push action of tc filter.
Usage:
tc filter add dev swp1 egress protocol 802.1Q flower indev swp0 skip_sw \
vlan_id 1 vlan_prio 1 action vlan push id 2 priority 2
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VCAP IS1 is a VCAP module which can filter on the most common L2/L3/L4
Ethernet keys, and modify the results of the basic QoS classification
and VLAN classification based on those flow keys.
There are 3 VCAP IS1 lookups, mapped over chains 10000, 11000 and 12000.
Currently the driver is hardcoded to use IS1_ACTION_TYPE_NORMAL half
keys.
Note that the VLAN_MANGLE has been omitted for now. In hardware, the
VCAP_IS1_ACT_VID_REPLACE_ENA field replaces the classified VLAN
(metadata associated with the frame) and not the VLAN from the header
itself. There are currently some issues which need to be addressed when
operating in standalone, or in bridge with vlan_filtering=0 modes,
because in those cases the switch ports have VLAN awareness disabled,
and changing the classified VLAN to anything other than the pvid causes
the packets to be dropped. Another issue is that on egress, we expect
port tagging to push the classified VLAN, but port tagging is disabled
in the modes mentioned above, so although the classified VLAN is
replaced, it is not visible in the packet transmitted by the switch.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Ocelot switches, there are 2 ingress pipelines for flow offload
rules: VCAP IS1 (Ingress Classification) and IS2 (Security Enforcement).
IS1 and IS2 support different sets of actions. The pipeline order for a
packet on ingress is:
Basic classification -> VCAP IS1 -> VCAP IS2
Furthermore, IS1 is looked up 3 times, and IS2 is looked up twice (each
TCAM entry can be configured to match only on the first lookup, or only
on the second, or on both etc).
Because the TCAMs are completely independent in hardware, and because of
the fixed pipeline, we actually have very limited options when it comes
to offloading complex rules to them while still maintaining the same
semantics with the software data path.
This patch maps flow offload rules to ingress TCAMs according to a
predefined chain index number. There is going to be a script in
selftests that clarifies the usage model.
There is also an egress TCAM (VCAP ES0, the Egress Rewriter), which is
modeled on top of the default chain 0 of the egress qdisc, because it
doesn't have multiple lookups.
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Co-developed-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the mscc_ocelot_switch_lib is common between a pure switchdev and
a DSA driver, the procedure of retrieving a net_device for a certain
port index differs, as those are registered by their individual
front-ends.
Up to now that has been dealt with by always passing the port index to
the switch library, but now, we're going to need to work with net_device
pointers from the tc-flower offload, for things like indev, or mirred.
It is not desirable to refactor that, so let's make sure that the flower
offload core has the ability to translate between a net_device and a
port index properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this stage, the tc-flower offload of mscc_ocelot can only delegate
rules to the VCAP IS2 security enforcement block. These rules have, in
hardware, separate bits for policing and for overriding the destination
port mask and/or copying to the CPU. So it makes sense that we attempt
to expose some more of that low-level complexity instead of simply
choosing between a single type of action.
Something similar happens with the VCAP IS1 block, where the same action
can contain enable bits for VLAN classification and for QoS
classification at the same time.
So model the action structure after the hardware description, and let
the high-level ocelot_flower.c construct an action vector from multiple
tc actions.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* lots more S1G band support
* 6 GHz scanning, finally
* kernel-doc fixes
* non-split wiphy dump fixes in nl80211
* various other small cleanups/features
-----BEGIN PGP SIGNATURE-----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=B9Xl
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of changes, this time with:
* lots more S1G band support
* 6 GHz scanning, finally
* kernel-doc fixes
* non-split wiphy dump fixes in nl80211
* various other small cleanups/features
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more generic eth_platform_get_mac_address() which can get a MAC
address from other than DT platform specific sources too. Check if the
obtained address is valid.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2:
If reading the MAC address from eeprom fail don't throw an error, use randomly
generated MAC instead. Either way the adapter will soldier on and the return
type of set_ethernet_addr() can be reverted to void.
v1:
Fix a bug in set_ethernet_addr() which does not take into account possible
errors (or partial reads) returned by its helpers. This can potentially lead to
writing random data into device's MAC address registers.
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indicate to the DSA receive path that we need to untage the bridge PVID,
this allows us to remove the dsa_untag_bridge_pvid() calls from
net/dsa/tag_brcm.c.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When interface is attached while in promiscuous mode and with VLAN
filtering turned off, both configurations are not respected and VLAN
filtering is performed.
There are 2 flows which add the any-vid rules during interface attach:
VLAN creation table and set rx mode. Each is relaying on the other to
add any-vid rules, eventually non of them does.
Fix this by adding any-vid rules on VLAN creation regardless of
promiscuous mode.
Fixes: 9df30601c8 ("net/mlx5e: Restore vlan filter after seamless reset")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Prior to this patch unloading an interface in promiscuous mode with RX
VLAN filtering feature turned off - resulted in a warning. This is due
to a wrong condition in the VLAN rules cleanup flow, which left the
any-vid rules in the VLAN steering table. These rules prevented
destroying the flow group and the flow table.
The any-vid rules are removed in 2 flows, but none of them remove it in
case both promiscuous is set and VLAN filtering is off. Fix the issue by
changing the condition of the VLAN table cleanup flow to clean also in
case of promiscuous mode.
mlx5_core 0000:00:08.0: mlx5_destroy_flow_group:2123:(pid 28729): Flow group 20 wasn't destroyed, refcount > 1
mlx5_core 0000:00:08.0: mlx5_destroy_flow_group:2123:(pid 28729): Flow group 19 wasn't destroyed, refcount > 1
mlx5_core 0000:00:08.0: mlx5_destroy_flow_table:2112:(pid 28729): Flow table 262149 wasn't destroyed, refcount > 1
...
...
------------[ cut here ]------------
FW pages counter is 11560 after reclaiming all pages
WARNING: CPU: 1 PID: 28729 at
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c:660
mlx5_reclaim_startup_pages+0x178/0x230 [mlx5_core]
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Call Trace:
mlx5_function_teardown+0x2f/0x90 [mlx5_core]
mlx5_unload_one+0x71/0x110 [mlx5_core]
remove_one+0x44/0x80 [mlx5_core]
pci_device_remove+0x3e/0xc0
device_release_driver_internal+0xfb/0x1c0
device_release_driver+0x12/0x20
pci_stop_bus_device+0x68/0x90
pci_stop_and_remove_bus_device+0x12/0x20
hv_eject_device_work+0x6f/0x170 [pci_hyperv]
? __schedule+0x349/0x790
process_one_work+0x206/0x400
worker_thread+0x34/0x3f0
? process_one_work+0x400/0x400
kthread+0x126/0x140
? kthread_park+0x90/0x90
ret_from_fork+0x22/0x30
---[ end trace 6283bde8d26170dc ]---
Fixes: 9df30601c8 ("net/mlx5e: Restore vlan filter after seamless reset")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Verify the configured FEC mode is supported by at least a single link
mode before applying the command. Otherwise fail the command and return
"Operation not supported".
Prior to this patch, the command was successful, yet it falsely set all
link modes to FEC auto mode - like configuring FEC mode to auto. Auto
mode is the default configuration if a link mode doesn't support the
configured FEC mode.
Fixes: b5ede32d33 ("net/mlx5e: Add support for FEC modes based on 50G per lane links")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Declare GRE offload support with respect to the inner protocol. Add a
list of supported inner protocols on which the driver can offload
checksum and GSO. For other protocols, inform the stack to do the needed
operations. There is no noticeable impact on GRE performance.
Fixes: 2729984149 ("net/mlx5e: Support TSO and TX checksum offloads for GRE tunnels")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The cited commit introduced the following coverity issue at function
mlx5_tc_ct_rule_to_tuple_nat:
- Memory - corruptions (OVERRUN)
Overrunning array "tuple->ip.src_v6.in6_u.u6_addr32" of 4 4-byte
elements at element index 7 (byte offset 31) using index
"ip6_offset" (which evaluates to 7).
In case of IPv6 destination address rewrite, ip6_offset values are
between 4 to 7, which will cause memory overrun of array
"tuple->ip.src_v6.in6_u.u6_addr32" to array
"tuple->ip.dst_v6.in6_u.u6_addr32".
Fixed by writing the value directly to array
"tuple->ip.dst_v6.in6_u.u6_addr32" in case ip6_offset values are
between 4 to 7.
Fixes: bc562be967 ("net/mlx5e: CT: Save ct entries tuples in hashtables")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Prior to this fix, in Striding RQ mode the driver was vulnerable when
receiving packets in the range (stride size - headroom, stride size].
Where stride size is calculated by mtu+headroom+tailroom aligned to the
closest power of 2.
Usually, this filtering is performed by the HW, except for a few cases:
- Between 2 VFs over the same PF with different MTUs
- On bluefield, when the host physical function sets a larger MTU than
the ARM has configured on its representor and uplink representor.
When the HW filtering is not present, packets that are larger than MTU
might be harmful for the RQ's integrity, in the following impacts:
1) Overflow from one WQE to the next, causing a memory corruption that
in most cases is unharmful: as the write happens to the headroom of next
packet, which will be overwritten by build_skb(). In very rare cases,
high stress/load, this is harmful. When the next WQE is not yet reposted
and points to existing SKB head.
2) Each oversize packet overflows to the headroom of the next WQE. On
the last WQE of the WQ, where addresses wrap-around, the address of the
remainder headroom does not belong to the next WQE, but it is out of the
memory region range. This results in a HW CQE error that moves the RQ
into an error state.
Solution:
Add a page buffer at the end of each WQE to absorb the leak. Actually
the maximal overflow size is headroom but since all memory units must be
of the same size, we use page size to comply with UMR WQEs. The increase
in memory consumption is of a single page per RQ. Initialize the mkey
with all MTTs pointing to a default page. When the channels are
activated, UMR WQEs will redirect the RX WQEs to the actual memory from
the RQ's pool, while the overflow MTTs remain mapped to the default page.
Fixes: 73281b78a3 ("net/mlx5e: Derive Striding RQ size from MTU")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Increase granularity of the error path to avoid unneeded free/release.
Fix the cleanup to be symmetric to the order of creation.
Fixes: 0ddf543226 ("xdp/mlx5: setup xdp_rxq_info")
Fixes: 422d4c401e ("net/mlx5e: RX, Split WQ objects for different RQ types")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In case of pci is offline reclaim_pages_cmd() will still try to call
the FW to release FW pages, cmd_exec() in this case will return a silent
success without actually calling the FW.
This is wrong and will cause page leaks, what we should do is to detect
pci offline or command interface un-available before tying to access the
FW and manually release the FW pages in the driver.
In this patch we share the code to check for FW command interface
availability and we call it in sensitive places e.g. reclaim_pages_cmd().
Alternative fix:
1. Remove MLX5_CMD_OP_MANAGE_PAGES form mlx5_internal_err_ret_value,
command success simulation list.
2. Always Release FW pages even if cmd_exec fails in reclaim_pages_cmd().
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
It is possible that new command entry index allocation will temporarily
fail. The new command holds the semaphore, so it means that a free entry
should be ready soon. Add one second retry mechanism before returning an
error.
Patch "net/mlx5: Avoid possible free of command entry while timeout comp
handler" increase the possibility to bump into this temporarily failure
as it delays the entry index release for non-callback commands.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
