LAN937x series of switches support 2 step timestamping mechanism. There
are timestamp correction calculation performed in ksz_rcv_timestamp and
ksz_xmit_timestamp which are applicable only for p2p1step. To check
whether the 2 step is enabled or not in tag_ksz.c introduced the helper
function in taggger_data to query it from ksz_ptp.c. Based on whether 2
step is enabled or not, timestamp calculation are performed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two programmable pins available for Trigger output unit to
generate periodic pulses. This patch add verify_pin for the available 2
pins and configure it with respect to GPIO index for the TOU unit.
Tested using testptp
./testptp -i 0 -L 0,2
./testptp -i 0 -d /dev/ptp0 -p 1000000000
./testptp -i 1 -L 1,2
./testptp -i 1 -d /dev/ptp0 -p 100000000
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN937x and KSZ PTP supported switches has Three Trigger output unit.
This TOU can used to generate the periodic signal for PTP. TOU has the
cycle width register of 32 bit in size and period width register of 24
bit, each value is of 8ns so the pulse width can be maximum 125ms.
Tested using ./testptp -d /dev/ptp0 -p 1000000000 -w 100000000 for
generating the 10ms pulse width
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For PDelay_Resp messages we will likely have a negative value in the
correction field. The switch hardware cannot correctly update such
values (produces an off by one error in the UDP checksum), so it must be
moved to the time stamp field in the tail tag. Format of the correction
field is 48 bit ns + 16 bit fractional ns. After updating the
correction field, clone is no longer required hence it is freed.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the routines for transmission of ptp packets. When the
ptp pdelay_req packet to be transmitted, it uses the deferred xmit
worker to schedule the packets.
During irq_setup, interrupt for Sync, Pdelay_req and Pdelay_rsp are
enabled. So interrupt is triggered for all three packets. But for
p2p1step, we require only time stamp of Pdelay_req packet. Hence to
avoid posting of the completion from ISR routine for Sync and
Pdelay_resp packets, ts_en flag is introduced. This controls which
packets need to processed for timestamp.
After the packet is transmitted, ISR is triggered. The time at which
packet transmitted is recorded to separate register.
This value is reconstructed to absolute time and posted to the user
application through socket error queue.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx Timestamping is done through 4 additional bytes in tail tag.
Whenever the ptp packet is received, the 4 byte hardware time stamped
value is added before 1 byte tail tag. Also, bit 7 in tail tag indicates
it as PTP frame. This 4 byte value is extracted from the tail tag and
reconstructed to absolute time and assigned to skb hwtstamp.
If the packet received in PDelay_Resp, then partial ingress timestamp
is subtracted from the correction field. Since user space tools expects
to be done in hardware.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP Interrupt mask and status register differ from the global and port
interrupt mechanism by two methods. One is that for global/port
interrupt enabling we have to clear the bit but for ptp interrupt we
have to set the bit. And other is bit12:0 is reserved in ptp interrupt
registers. This forced to not use the generic implementation of
global/port interrupt method routine. This patch implement the ptp
interrupt mechanism to read the timestamp register for sync, pdelay_req
and pdelay_resp.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is used for reconstructing the absolute time from the 32bit
hardware time stamping value. The do_aux ioctl is used for reading the
ptp hardware clock and store it to global variable.
The timestamped value in tail tag during rx and register during tx are
32 bit value (2 bit seconds and 30 bit nanoseconds). The time taken to
read entire ptp clock will be time consuming. In order to speed up, the
software clock is maintained. This clock time will be added to 32 bit
timestamp to get the absolute time stamp.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PTP is enabled in hardware bit 6 of PTP_MSG_CONF1 register, the
transmit frame needs additional 4 bytes before the tail tag. It is
needed for all the transmission packets irrespective of PTP packets or
not.
The 4-byte timestamp field is 0 for frames other than Pdelay_Resp. For
the one-step Pdelay_Resp, the switch needs the receive timestamp of the
Pdelay_Req message so that it can put the turnaround time in the
correction field.
Since PTP has to be enabled for both Transmission and reception
timestamping, driver needs to track of the tx and rx setting of the all
the user ports in the switch.
Two flags hw_tx_en and hw_rx_en are added in ksz_port to track the
timestampping setting of each port. When any one of ports has tx or rx
timestampping enabled, bit 6 of PTP_MSG_CONF1 is set and it is indicated
to tag_ksz.c through tagger bytes. This flag adds 4 additional bytes to
the tail tag. When tx and rx timestamping of all the ports are disabled,
then 4 bytes are not added.
Tested using hwstamp -i <interface>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> # mostly api
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the routine for get_ts_info, hwstamp_get, set. This enables
the PTP support towards userspace applications such as linuxptp.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implement routines (adjfine, adjtime, gettime and settime)
for manipulating the chip's PTP clock. It registers the ptp caps
to posix clock register.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> # mostly api
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ swithes used interrupts for detecting the phy link up and down.
During registering the interrupt handler, it used IRQF_TRIGGER_FALLING
flag. But this flag has to be retrieved from device tree instead of hard
coding in the driver, so removing the flag.
Fixes: ff319a6448 ("net: dsa: microchip: move interrupt handling logic from lan937x to ksz_common")
Reported-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20221213101440.24667-1-arun.ramadoss@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To make the code more comparable to KSZ9477 code, move DSA
configurations to the same location.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
KSZ8795 and KSZ9477 compatible series of switches use global max frame
size configuration register. So, enable MTU normalization for this reason.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make MTU configurable on KSZ87xx and KSZ88xx series of switches.
Before this patch, pre-configured behavior was different on different
switch series, due to opposite meaning of the same bit:
- KSZ87xx: Reg 4, Bit 1 - if 1, max frame size is 1532; if 0 - 1514
- KSZ88xx: Reg 4, Bit 1 - if 1, max frame size is 1514; if 0 - 1532
Since the code was telling "... SW_LEGAL_PACKET_DISABLE, true)", I
assume, the idea was to set max frame size to 1532.
With this patch, by setting MTU size 1500, both switch series will be
configured to the 1532 frame limit.
This patch was tested on KSZ8873.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add ksz_rmw8(), it will be used in the next patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If we have global MTU configuration, it is enough to configure it on CPU
port only.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are no HW specific registers, so we can process all of them
in one location.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Arun Ramadoss <arun.ramadoss@microchip.com> (KSZ9893 and LAN937x)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no reason that I can see why the no-op tagging protocol should
be registered manually, so make it a module and make all drivers which
have any sort of reference to DSA_TAG_PROTO_NONE select it.
Note that I don't know if ksz_get_tag_protocol() really needs this,
or if it's just the logic which is poorly written. All switches seem to
have their own tagging protocol, and DSA_TAG_PROTO_NONE is just a
fallback that never gets used.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Probe functions uses normal dev_err() to check error conditions
and print messages. Replace dev_err() with dev_err_probe() to
have more standardized format and error logging.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ8563 have three port interrupts: PTP, PHY and ACL. Add
port_nirq as 3 for KSZ8563 inside ksz_chip_data.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add status validation for port register write inside
lan937x_change_mtu. ksz_pwrite and ksz_pread api's are
updated with return type int (Reference patch mentioned
below). Update lan937x_change_mtu with status validation
for ksz_pwrite16().
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20220826105634.3855578-6-o.rempel@pengutronix.de/
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add device irq in i2c probe function.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add KSZ9563 inside ksz_switch_chips structure with
port_nirq as 3. KSZ9563 use KSZ9893 switch parameters
but port_nirq count is 3 for KSZ9563 whereas 2 for
KSZ9893. Add KSZ9563 inside ksz_switch_chips as a separate
member and from device tree map compatible string into
KSZ9563 inside ksz_spi.c and ksz9477_i2c.c.
Global Chip ID 1 and 2 registers read value 9893, select
sku based on Global Chip ID 4 Register which read 0x1c
for KSZ9563.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixes all over the tree. Other subsystems depending on this change
have been asked to pull an immutable topic branch for this.
* new driver for Microchip PCI1xxxx switch
* heavy refactoring of the Mellanox BlueField driver
* we prefer async probe in the i801 driver now
* the rest is usual driver updates (support for more SoCs, some
refactoring, some feature additions)
-----BEGIN PGP SIGNATURE-----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=arni
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- 'remove' callback converted to return void. Big change with trivial
fixes all over the tree. Other subsystems depending on this change
have been asked to pull an immutable topic branch for this.
- new driver for Microchip PCI1xxxx switch
- heavy refactoring of the Mellanox BlueField driver
- we prefer async probe in the i801 driver now
- the rest is usual driver updates (support for more SoCs, some
refactoring, some feature additions)
* tag 'i2c-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
i2c: pci1xxxx: prevent signed integer overflow
i2c: acpi: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
i2c: i801: Prefer async probe
i2c: designware-pci: Use standard pattern for memory allocation
i2c: designware-pci: Group AMD NAVI quirk parts together
i2c: microchip: pci1xxxx: Add driver for I2C host controller in multifunction endpoint of pci1xxxx switch
docs: i2c: slave-interface: return errno when handle I2C_SLAVE_WRITE_REQUESTED
i2c: mlxbf: remove device tree support
i2c: mlxbf: support BlueField-3 SoC
i2c: cadence: Add standard bus recovery support
i2c: mlxbf: add multi slave functionality
i2c: mlxbf: support lock mechanism
macintosh/ams: Adapt declaration of ams_i2c_remove() to earlier change
i2c: riic: Use devm_platform_ioremap_resource()
i2c: mlxbf: remove IRQF_ONESHOT
dt-bindings: i2c: rockchip: add rockchip,rk3128-i2c
dt-bindings: i2c: renesas,rcar-i2c: Add r8a779g0 support
i2c: tegra: Add GPCDMA support
i2c: scmi: Convert to be a platform driver
i2c: rk3x: Add rv1126 support
...
Remove unnecessary i2c_set_clientdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The global port interrupt routines and individual ports interrupt
routines has similar implementation except the mask & status register
and number of nested irqs in them. The mask & status register and
pointer to ksz_device is added to ksz_irq and uses the ksz_irq as
irq_chip_data.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To support the phy link detection through interrupt method for ksz9477
based switch, the interrupt handling routines are moved from
lan937x_main.c to ksz_common.c. The only changes made are functions
names are prefixed with ksz_ instead of lan937x_.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, if the mdio node is not present in the dts file then
lan937x_mdio_register return -ENODEV and entire probing process fails.
To make the mdio_register generic for all ksz series switches and to
maintain back-compatibility with existing dts file, return -ENODEV is
replaced with return 0.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the lan937x_mdio_register function, phy interrupts are enabled
irrespective of irq is enabled in the switch. Now, the check is added to
enable the phy interrupt only if the irq is enabled in the switch.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the number of port irqs is hard coded for the lan937x switch
as 6. In order to make the generic interrupt handler for ksz switches,
number of port irq supported by the switch is added to the
ksz_chip_data. It is 4 for ksz9477, 2 for ksz9897 and 3 for ksz9567.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Maximum frame length check is enabled in lan937x switch on POR, But it
is found to be disabled on driver during port setup operation. Due to
this, packets are not dropped when transmitted with greater than configured
value. For testing, setup made for lan1->lan2 transmission and configured
lan1 interface with a frame length (less than 1500 as mentioned in
documentation) and transmitted packets with greater than configured value.
Expected no packets at lan2 end, but packets observed at lan2.
Based on the documentation, packets should get discarded if the actual
packet length doesn't match the frame length configured. Frame length check
should be disabled only for cascaded ports due to tailtags.
This feature was disabled on ksz9477 series due to ptp issue, which is
not in lan937x series. But since lan937x took ksz9477 as base, frame
length check disabled here as well. Patch added to remove this portion
from port setup so that maximum frame length check will be active for
normal ports.
Fixes: 55ab6ffaf3 ("net: dsa: microchip: add DSA support for microchip LAN937x")
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Link: https://lore.kernel.org/r/20220912051228.1306074-1-rakesh.sankaranarayanan@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This node pointer is returned by of_find_compatible_node() with
refcount incremented in this function. of_node_put() on it before
exitting this function.
Fixes: c9cd961c0d ("net: dsa: microchip: lan937x: add interrupt support for port phy link")
Signed-off-by: Sun Ke <sunke32@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220908040226.871690-1-sunke32@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KSZ9477 has the 11 bit ageing count value which is split across the two
registers. And LAN937x has the 20 bit ageing count which is also split
into two registers. Each count in the registers represents 1 second.
This patch add the support for ageing time for KSZ9477 and LAN937x
series of switch.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
According to the KSZ9477S datasheet, there is no global register
at 0x033C and 0x033D addresses.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the KSZ9896 6-port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9896 supports both SPI (already in) and I2C.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the KSZ9896 6-port Gigabit Ethernet Switch to the
ksz9477 driver.
Although the KSZ9896 is already listed in the device tree binding
documentation since a1c0ed24fe (dt-bindings: net: dsa: document
additional Microchip KSZ9477 family switches) the chip id
(0x00989600) is not recognized by ksz_switch_detect() and rejected
by the driver.
The KSZ9896 is similar to KSZ9897 but has only one configurable
MII/RMII/RGMII/GMII cpu port.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the interrupts for internal phy link detection for
LAN937x. The interrupt enable bits are active low. There is global
interrupt mask for each port. And each port has the individual interrupt
mask for TAS. QCI, SGMII, PTP, PHY and ACL.
The first level of interrupt domain is registered for global port
interrupt and second level of interrupt domain for the individual port
interrupts. The phy interrupt is enabled in the lan937x_mdio_register
function. Interrupt from which port is raised will be detected based on
the interrupt host data.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the lan937x_reset_switch(), it masks all the switch and port
registers. In the Global_Int_status register, POR ready bit is write 1
to clear bit and all other bits are read only. So, this patch clear the
por_ready_int status bit by writing 1.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct ksz_port doesn't have reference to ksz_device as of now. In order
to find out from which port interrupt has triggered, we need to pass the
struct ksz_port as a host data. When the interrupt is triggered, we can
get the port from which interrupt triggered, but to identify it is phy
interrupt we have to read status register. The regmap structure for
accessing the device register is present in the ksz_device struct. To
access the ksz_device from the ksz_port, the reference is added to it
with port number as well.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After driver refactoring we was running ksz9477 specific CPU port
configuration on ksz8 family which ended with kernel oops. So, make sure
we run this code only on ksz9477 compatible devices.
Tested on KSZ8873 and KSZ9477.
Fixes: da8cd08520 ("net: dsa: microchip: add support for common phylink mac link up")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use chip_id as other places of this code do it
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is not used. So, remove it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is not used on ksz9477 side. Remove it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is unused. So, drop it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With code refactoring was introduced new variable internal_phy. Let's
use it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add register validation for KSZ9477
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason why PHYlib may access MII_CTRL1000 on the chip without GBit
support is only if chip provides wrong information about extended caps
register. This issue is now handled by ksz9477_r_phy_quirks()
With proper regmap_ranges provided for all chips we will be able to
catch this kind of bugs any way. So, remove this sanity check.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add register validation for KSZ8563.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is complex driver with support for different chips with different
layouts. To detect at least some bugs earlier, we should validate register
accesses by using regmap_access_table support.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was detected after adding regmap register access validation.
KSZ9893 compatible chips do not have "Output Clock Control Register
0x0103". So, avoid writing to it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now ksz_pread/ksz_pwrite can return error value. So, make use of it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now ksz_pread/ksz_pwrite can return error value. So, make use of it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz_read*/ksz_write* are able to return errors, so forward it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY access may end with errors on different levels. So, allow to forward
return values where possible.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was detected after adding support of regmap_ranges for KSZ8563R
chip. This chip is reporting extended registers support without having
actual extended registers. This made PHYlib request not existing
registers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ8563 has two 100Mbit PHYs and CPU port with RGMII support. Since
1000Mbit configuration for the RGMII capable MAC is present, we should
use per port validation.
As main part of migration to per-port validation we need to rework
ksz9477_switch_init() function. Which is using undocumented
REG_GLOBAL_OPTIONS register to detect per-chip Gbit support. So, it is
related to some sort of risk for regressions.
To reduce this risk I compared the code with publicly available
documentations. This function will executed on following currently
supported chips:
struct ksz_chip_data OF compatible
KSZ9477 KSZ9477
KSZ9897 KSZ9897
KSZ9893 KSZ9893, KSZ9563
KSZ8563 KSZ8563
KSZ9567 KSZ9567
Only KSZ9893, KSZ9563, KSZ8563 document existence of 0xf ==
REG_GLOBAL_OPTIONS register with bit field description "SKU ID":
KSZ9893 0x0C
KSZ9563 0x1C
KSZ8563 0x3C
The existence of hidden flags is not documented.
KSZ9477, KSZ9897, KSZ9567 do not document this register at all.
Only KSZ8563 is documented as non Gbit chip: 100Mbit PHYs and RGMII CPU
port. So, this change should not introduce a regression for
configurations with properly used OF compatibles.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add separate entry for the KSZ8563 chip. According to the documentation
it can support Gbit only on RGMII port. So, we will need to be able to
describe in the followup patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Address learning should initially be turned off by the driver for port
operation in standalone mode, then the DSA core handles changes to it
via ds->ops->port_bridge_flags().
Leaving address learning enabled while ports are standalone breaks any
kind of communication which involves port B receiving what port A has
sent. Notably it breaks the ksz9477 driver used with a (non offloaded,
ports act as if standalone) bonding interface in active-backup mode,
when the ports are connected together through external switches, for
redundancy purposes.
This fixes a major design flaw in the ksz9477 and ksz8795 drivers, which
unconditionally leave address learning enabled even while ports operate
as standalone.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Link: https://lore.kernel.org/netdev/CAFZh4h-JVWt80CrQWkFji7tZJahMfOToUJQgKS5s0_=9zzpvYQ@mail.gmail.com/
Reported-by: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220818164809.3198039-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DSA has multiple ways of specifying a MAC connection to an internal PHY.
One requires a DT description like this:
port@0 {
reg = <0>;
phy-handle = <&internal_phy>;
phy-mode = "internal";
};
(which is IMO the recommended approach, as it is the clearest
description)
but it is also possible to leave the specification as just:
port@0 {
reg = <0>;
}
and if the driver implements ds->ops->phy_read and ds->ops->phy_write,
the DSA framework "knows" it should create a ds->slave_mii_bus, and it
should connect to a non-OF-based internal PHY on this MDIO bus, at an
MDIO address equal to the port address.
There is also an intermediary way of describing things:
port@0 {
reg = <0>;
phy-handle = <&internal_phy>;
};
In case 2, DSA calls phylink_connect_phy() and in case 3, it calls
phylink_of_phy_connect(). In both cases, phylink_create() has been
called with a phy_interface_t of PHY_INTERFACE_MODE_NA, and in both
cases, PHY_INTERFACE_MODE_NA is translated into phy->interface.
It is important to note that phy_device_create() initializes
dev->interface = PHY_INTERFACE_MODE_GMII, and so, when we use
phylink_create(PHY_INTERFACE_MODE_NA), no one will override this, and we
will end up with a PHY_INTERFACE_MODE_GMII interface inherited from the
PHY.
All this means that in order to maintain compatibility with device tree
blobs where the phy-mode property is missing, we need to allow the
"gmii" phy-mode and treat it as "internal".
Fixes: 2c709e0bda ("net: dsa: microchip: ksz8795: add phylink support")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216320
Reported-by: Craig McQueen <craig@mcqueen.id.au>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20220818143250.2797111-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the ksz9477_fdb_dump function it reads the ALU control register and
exit from the timeout loop if there is valid entry or search is
complete. After exiting the loop, it reads the alu entry and report to
the user space irrespective of entry is valid. It works till the valid
entry. If the loop exited when search is complete, it reads the alu
table. The table returns all ones and it is reported to user space. So
bridge fdb show gives ff:ff:ff:ff:ff:ff as last entry for every port.
To fix it, after exiting the loop the entry is reported only if it is
valid one.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220816105516.18350-1-arun.ramadoss@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This patch add support for phylink mac config for ksz series of
switches. All the files ksz8795, ksz9477 and lan937x uses the ksz common
xmii function. Instead of calling from the individual files, it is moved
to the ksz common phylink mac config function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the ksz8795 cpu configuration to use the ksz common
xmii set functions.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ksz9477.c file, configuring the xmii register is performed based on
the flag NEW_XMII. The flag is reset for ksz9893 switch and set for
other switch. This patch uses the ksz common xmii set and get function.
The bit values are configured based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch read the rgmii tx and rx delay from device tree and stored it
in the ksz_port. It applies the rgmii delay to the xmii tune adjust
register based on the interface selected in phylink mac config. There
are two rgmii port in LAN937x and value to be loaded in the register
vary depends on the port selected.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the common ksz_set_xmii function for ksz series switch
and update the lan937x code phylink mac config. The register address for
the ksz8795 is Port 5 Interface control 6 and for all other switch is
xMII Control 1.
The bit value for selecting the interface is same for
KSZ8795 and KSZ9893 are same. The bit values for KSZ9477 and lan973x are
same. So, this patch add the bit value for each switches in
ksz_chip_data and configure the registers based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for common phylink mac link up for the ksz
series switch. The register address, bit position and values are
configured based on the chip id to the dev->info structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add common function for configuring the Full/Half duplex and
transmit/receive flow control. KSZ8795 uses the Global control register
4 for configuring the duplex and flow control, whereas all other KSZ9477
based switch uses the xMII Control 0 register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the function for configuring the 100/10Mbps speed
selection for the ksz switches. KSZ8795 switch uses Global control 4
register 0x06 bit 4 for choosing 100/10Mpbs. Other switches uses xMII
control 1 0xN300 for it.
For KSZ8795, if the bit is set then 10Mbps is chosen and if bit is
clear then 100Mbps chosen. For all other switches it is other way
around, if the bit is set then 100Mbps is chosen.
So, this patch add the generic function for ksz switch to select the
100/10Mbps speed selection. While configuring, first it disables the
gigabit functionality and then configure the respective speed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add helper function for setting and getting the gigabit
enable for the ksz series switch. KSZ8795 switch has different register
address compared to all other ksz switches. KSZ8795 series uses the Port
5 Interface control 6 Bit 6 for configuring the 1Gbps or 100/10Mbps
speed selection. All other switches uses the xMII control 1 0xN301
register Bit6 for gigabit.
Further, for KSZ8795 & KSZ9893 switches if bit 1 then 1Gbps is chosen
and if bit 0 then 100/10Mbps is chosen. It is other way around for
other switches bit 0 is for 1Gbps. So, this patch implements the common
function for configuring the gigabit set and get capability.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the refactoring for the ksz8_dev_ops from ksz8795.c to
ksz_common.c, the ksz8_r_mib_cnt has been missed. So this patch adds the
missing one.
Fixes: 6ec23aaaac ("net: dsa: microchip: move ksz_dev_ops to ksz_common.c")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220718061803.4939-1-arun.ramadoss@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch removes the of_match_ptr() pointer when dereferencing the
ksz_dt_ids which produce the unused variable warning.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ksz_switch_register(), we should call of_node_put() for the
reference returned by of_get_child_by_name() which has increased
the refcount.
Fixes: 912aae27c6 ("net: dsa: microchip: really look for phy-mode in port nodes")
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220714153138.375919-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch add the LAN937x part support in the existing ksz_spi_probe.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for phylink_mac_config dsa hook. It configures
the mac for MII/RMII modes. The RGMII mode will be added in the future
patches.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for phylink_mac_link_up. It configures the mac
for the speed, flow control and duplex mode.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal phy of the LAN937x are capable of 100Mbps Full duplex. The
xMII port of switch is capable of 10Mbps Full & Half Duplex, 100Mbps
Full & Half Duplex and 1000Mbps Half duplex. xMII port also supports Tx
and Rx Flow control.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for port_max_mtu, port_change_mtu and
port_fast_age dsa functionality.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch register mdio-bus for the lan937x series switch. mdio read
and write uses the vphy for accessing the phy register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for the writing and reading of the phy registers.
LAN937x uses the Vphy indirect addressing method for accessing the phys.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch update the ksz_get_tag_protocol to return LAN937x specific
tag if the chip id matches one of LAN937x series switch
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic DSA driver support for lan937x and the device will be
configured through SPI interface.
It adds the lan937x_dev_ops in ksz_common.c file and tries to reuse the
functionality of ksz9477 series switch.
drivers/net/dsa/microchip/ path is already part of MAINTAINERS &
the new files come under this path. Hence no update needed to the
MAINTAINERS
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz9477 and lan937x has few difference in the static and reserved
table register 0x041C. For the ksz9477 if the bit 0 is 1 - read
operation and 0 - write operation. But for lan937x bit 1:0 used for
selecting the read/write operation, 01 - write and 10 - read.
To use ksz9477 mdb add/del and enable_stp_addr for the lan937x, masks &
shifts are introduced for ksz9477 & lan937x in ksz_common.c. Then
updated the function with masks & shifts based on the switch instead of
hard coding it.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switch is calculating tx/rx_bytes for all packets including pause.
So, include rx/tx_pause counter to rx/tx_packets to make tx/rx_bytes fit
to rx/tx_packets.
Link: https://lore.kernel.org/all/20220624220317.ckhx6z7cmzegvoqi@skbuf/
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for pause specific stats.
Tested on ksz9477.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch moves the broadcast ctrl, multicast ctrl and start control
registers from ksz_chip_dat to ksz_chip_reg.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the stp_ctrl_reg from the ksz_chip_data to ksz_chip_reg
structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register size for the ksz8 switches is u8 and for ksz9477 series is
u16. To have common struct for ksz series switches the size of reg is
increased from u8 to u16.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the struct ksz8 from ksz8.h which is no longer
needed. The platform bus specific details are now deferenced through
dev->priv.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves ksz8->shifts from ksz8795.c to ksz_common.c. The shifts
are dereferenced using dev->info->shifts.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
