The V3(s) will detect a valid external low frequency clock and if it is
not present will automatically switch to the internal one. This might
hide bugs and (hardware) configuration errors. It's even worse because
the internal RTC runs significantly slower (32.000Hz vs 32.768Hz).
Fortunately for us, the V3(s) has an (undocumented) bypass of this
switching and the driver already supports it by setting the
.has_auto_swt flag.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20240730194905.2587202-1-mwalle@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There's no need to list "s35390a" in the DT match table. The I2C core
will strip any vendor prefix and match against the i2c_device_id table
which has an "s35390a" entry.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240826191321.1410668-1-robh@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The BBM module provides RTC feature. To i.MX95, this module is managed by
System Manager and exported System Control Management Interface(SCMI).
Linux could use i.MX SCMI BBM Extension protocol to use RTC feature.
This driver is to use SCMI interface to get/set RTC.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Message-Id: <20240823-imx95-bbm-misc-v2-v8-6-e600ed9e9271@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
STM32 RTC can pulse some SOC pins when an RTC alarm expires.
This patch adds this functionality for alarm A. The pulse can out on three
pins RTC_OUT1, RTC_OUT2, RTC_OUT2_RMP (PC13, PB2, PI8 on stm32mp15)
(PC13, PB2, PI1 on stm32mp13) (PC13, PF4/PF6, PI8 on stm32mp25).
This patch only adds the functionality for devices which are using
st,stm32mp1-rtc and st,stm32mp25-rtc compatible.
Add "alarm-a" in pinmux functions.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240722160022.454226-5-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
RTC is able to output on a pin the "LSE" internal clock.
STM32 RTC is now registered as a clock provider.
It provides rtc_lsco clock, that means RTC_LSCO is output on either
RTC_OUT1 or RTC_OUT2_RMP, depending on pinmux DT property.
The clock is marked as CLK_IGNORE_UNUSED and CLK_IS_CRITICAL because
RTC_LSCO can be early required by devices needed it to init.
Add LSCO in pinmux functions.
Add "stm32_rtc_clean_outs" to disable LSCO. As RTC is part of "backup"
power domain, it is not reset during shutdown or reboot. So force LSCO
disable at probe.
Co-developed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20240722160022.454226-4-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
STM32 RTC is capable to handle 3 specific pins of the soc.
"out1, out2 and out2_rmp". To handle this, we use pinctrl framework.
There is a single pin per group.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240722160022.454226-3-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Introduce new st,stm32mp25-rtc compatible. It is based on st,stm32mp1-rtc.
Difference is that stm32mp25 soc implements a triple protection on RTC
registers:
- Secure bit based protection
- Privileged context based protection
- Compartment ID filtering based protection
This driver will now check theses configurations before probing to avoid
exceptions and fake reads on register.
At this time, driver needs only to check two resources: INIT and ALARM_A.
Other resources are not used.
Resource isolation framework (RIF) is a comprehensive set of hardware
blocks designed to enforce and manage isolation of STM32 hardware
resources, like memory and peripherals.
Link: https://www.st.com/resource/en/reference_manual/rm0457-stm32mp25xx-advanced-armbased-3264bit-mpus-stmicroelectronics.pdf#page=4081
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20240708153434.416287-3-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove a comma after the sentinel entry in
rtc-hym8563.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240515194336.58342-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
`rtc_add_offset()` is called by `__rtc_read_time()`
and `__rtc_read_alarm()` to add the RTC's offset to
the raw read-outs from the device drivers. However,
in the latter case, a fix-up algorithm is run if
the RTC device does not report a full `struct rtc_time`
alarm value. In that case, the offset was forgot to be
added.
Fixes: fd6792bb02 ("rtc: fix alarm read and set offset")
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Link: https://lore.kernel.org/r/20240619140451.2800578-1-csokas.bence@prolan.hu
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
`tm_year` may go up to 299 if the device supports the
century bit. Therefore, subtracting may not give us
a valid 2-digit number, but modulo does.
Co-developed-by: Szentendrei, Tamás <szentendrei.tamas@prolan.hu>
Signed-off-by: Szentendrei, Tamás <szentendrei.tamas@prolan.hu>
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Link: https://lore.kernel.org/r/20240611072411.671600-2-csokas.bence@prolan.hu
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch enables the detection of the oscillator failure on mcp794xx chips.
Co-developed-by: Szentendrei, Tamás <szentendrei.tamas@prolan.hu>
Signed-off-by: Szentendrei, Tamás <szentendrei.tamas@prolan.hu>
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Link: https://lore.kernel.org/r/20240611072411.671600-1-csokas.bence@prolan.hu
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As per the latest HW manual[1], there is an internal delay(~250 microsec)
from setting ALME = 0 to disabling the alarm function, so the user must
add a short delay of greater than 250µs between setting ALME = 0 and
clearing ALM.
Currently setting of ALME = 0 is done after clearing the ALM, so just
reverse the operation and add a delay of 275 microsec.
[1]https://www.renesas.com/us/en/document/dst/raa215300-datasheet?r=1506351
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20240618152635.48956-3-biju.das.jz@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As per the latest HW manual[1], the INT# output is pulled low after the
alarm is triggered. After the INT# output is pulled low, it is low for at
least 250ms, even if the correct action is taken to clear it. It is
impossible to clear ALM if it is still active. The host must wait for the
RTC to progress past the alarm time plus the 250ms delay before clearing
ALM.
[1]https://www.renesas.com/us/en/document/dst/raa215300-datasheet?r=1506351
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20240618152635.48956-2-biju.das.jz@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/rtc/lib_test.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/rtc/rtc-goldfish.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/rtc/rtc-omap.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/rtc/rtc-rc5t583.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/rtc/rtc-tps65910.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/rtc/rtc-twl.o
Add the missing invocation of the MODULE_DESCRIPTION() macro to all
files which have a MODULE_LICENSE(). This includes rtc-mpc5121.c,
which does not produce a warning with the x86 allmodconfig since it is
not built for x86, but it may cause this warning with Freescale PPC
configurations.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240608-md-drivers-rtc-v1-1-5f44222adfae@quicinc.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Read callbacks registered with nvmem core expect 0 to be returned on
success and a negative value to be returned on failure.
abx80x_nvmem_xfer() on read calls i2c_smbus_read_i2c_block_data() which
returns the number of bytes read on success as per its api description,
this return value is handled as an error and returned to nvmem even on
success.
Fix to handle all possible values that would be returned by
i2c_smbus_read_i2c_block_data().
Fixes: e90ff8ede7 ("rtc: abx80x: Add nvmem support")
Cc: stable@vger.kernel.org
Signed-off-by: Joy Chakraborty <joychakr@google.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240613120750.1455209-1-joychakr@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Read/write callbacks registered with nvmem core expect 0 to be returned
on success and a negative value to be returned on failure.
cmos_nvram_read()/cmos_nvram_write() currently return the number of
bytes read or written, fix to return 0 on success and -EIO incase number
of bytes requested was not read or written.
Fixes: 8b5b7958fd ("rtc: cmos: use generic nvmem")
Cc: stable@vger.kernel.org
Signed-off-by: Joy Chakraborty <joychakr@google.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20240612083635.1253039-1-joychakr@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Read/write callbacks registered with nvmem core expect 0 to be returned
on success and a negative value to be returned on failure.
isl1208_nvmem_read()/isl1208_nvmem_write() currently return the number of
bytes read/written on success, fix to return 0 on success and negative on
failure.
Fixes: c3544f6f51 ("rtc: isl1208: Add new style nvmem support to driver")
Cc: stable@vger.kernel.org
Signed-off-by: Joy Chakraborty <joychakr@google.com>
Link: https://lore.kernel.org/r/20240612080831.1227131-1-joychakr@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add power management support to the driver. This allows a SoC to wake
from suspend using the nINT provided by the RTC.
It takes care of the case when the interrupt has not been caught because
the kernel has not yet woke up.
(This is the case when only edges interrupt are caught)
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Link: https://lore.kernel.org/r/20240618141851.1810000-4-richard.genoud@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch will prepare for the next one (power management support) by
introducing struct tps6594_rtc.
No functionnal change.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Link: https://lore.kernel.org/r/20240618141851.1810000-3-richard.genoud@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
struct rtc_device is allocated twice in probe(), once with
devm_kzalloc(), and then with devm_rtc_allocate_device().
The allocation with devm_kzalloc() is lost and superfluous.
Fixes: 9f67c1e639 ("rtc: tps6594: Add driver for TPS6594 RTC")
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Link: https://lore.kernel.org/r/20240618141851.1810000-2-richard.genoud@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In some platforms, the RTC is able to wake up the system but is not
directly connected to an IRQ. Add wakeup-source property support to be able
to express this in the Device Tree.
Link: https://lore.kernel.org/r/20240426225821.448963-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Allow userspace to get battery status information and be able to warn when
battery is low and has to be replaced.
Tested-by: Waqar Hameed <waqar.hameed@axis.com>
Reviewed-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://lore.kernel.org/r/20240417191937.33790-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The proper way for userspace to react on a read time error is to have a
look at the voltage low information. There is no point in cluttering dmesg
as it is often not even visible to the end user.
Reviewed-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://lore.kernel.org/r/20240417191937.33790-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
'regmap_spi_config' and 'regmap_i2c_config' are not modified in this diver
and are only used as a const struct regmap_config.
Constifying these structures moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
text data bss dec hex filename
8896 1554 32 10482 28f2 drivers/rtc/rtc-rx6110.o
After:
text data bss dec hex filename
9536 914 32 10482 28f2 drivers/rtc/rtc-rx6110.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/833a7f612c0de9dcb1179a0b75b189c237a335ac.1714862560.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The ID table already has respective entry and MODULE_DEVICE_TABLE and
creates proper alias for SPI driver. Having another MODULE_ALIAS causes
the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240414154910.126991-1-krzk@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On slow systems, the rtc unit test may result in soft lockups and/or
generate messages such as
# rtc_time64_to_tm_test_date_range: Test should be marked slow (runtime: 34.253230015s)
# rtc_time64_to_tm_test_date_range: pass:1 fail:0 skip:0 total:1
The test covers a date range of 160,000 years, resulting in the long
runtime.
Unit tests running for more than 1 second are supposed to be marked as
slow. Just marking the test as slow would prevent it from running when
slow tests are disabled, which would not be desirable. At the same time,
the current test range of 160,000 years seems to be of limited value.
Split the test into two parts, one covering a range of 1,000 years and
the other covering the current range of 160,000 years. Mark the 160,000
year test as slow to be able to separate it from the faster test.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240313174221.1999654-1-linux@roeck-us.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Subsytem:
- rtc_class is now const
Drivers:
- ds1511: driver cleanup, set date and time range and alarm offset limit
- max31335: fix interrupt handler
- pcf8523: improve suspend support
-----BEGIN PGP SIGNATURE-----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=Is7n
-----END PGP SIGNATURE-----
Merge tag 'rtc-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsytem:
- rtc_class is now const
Drivers:
- ds1511: cleanup, set date and time range and alarm offset limit
- max31335: fix interrupt handler
- pcf8523: improve suspend support"
* tag 'rtc-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (28 commits)
MAINTAINER: Include linux-arm-msm for Qualcomm RTC patches
dt-bindings: rtc: zynqmp: Add support for Versal/Versal NET SoCs
rtc: class: make rtc_class constant
dt-bindings: rtc: abx80x: Improve checks on trickle charger constraints
MAINTAINERS: adjust file entry in ARM/Mediatek RTC DRIVER
rtc: nct3018y: fix possible NULL dereference
rtc: max31335: fix interrupt status reg
rtc: mt6397: select IRQ_DOMAIN instead of depending on it
dt-bindings: rtc: abx80x: convert to yaml
rtc: m41t80: Use the unified property API get the wakeup-source property
dt-bindings: at91rm9260-rtt: add sam9x7 compatible
dt-bindings: rtc: convert MT7622 RTC to the json-schema
dt-bindings: rtc: convert MT2717 RTC to the json-schema
rtc: pcf8523: add suspend handlers for alarm IRQ
rtc: ds1511: set alarm offset limit
rtc: ds1511: set range
rtc: ds1511: drop inline/noinline hints
rtc: ds1511: rename pdata
rtc: ds1511: implement ds1511_rtc_read_alarm properly
rtc: ds1511: remove partial alarm support
...
Since commit 43a7206b09 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the rtc_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240305-class_cleanup-abelloni-v1-1-944c026137c8@marliere.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix the register value comparison in the `max31335_volatile_reg`
function for the interrupt status register.
MAX31335_STATUS1 macro definition corresponds to the actual
interrupt status register.
Fixes: dedaf03b99 ("rtc: max31335: add driver support")
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240219091616.24480-1-antoniu.miclaus@analog.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
IRQ_DOMAIN is a hidden (not user visible) symbol. Users cannot set
it directly thru "make *config", so drivers should select it instead
of depending on it if they need it.
Relying on it being set for a dependency is risky.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on" for IRQ_DOMAIN to
"select" for RTC_DRV_MT6397.
Fixes: 04d3ba70a3 ("rtc: mt6397: add IRQ domain dependency")
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Eddie Huang <eddie.huang@mediatek.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-rtc@vger.kernel.org
Cc: Marc Zyngier <maz@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Peter Rosin <peda@axentia.se>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20240213050258.6167-1-rdunlap@infradead.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This allows both ACPI and Device Tree systems to specify the m41t80 as a
wakeup-source.
Signed-off-by: Curtis Klein <curtis.klein@hpe.com>
Link: https://lore.kernel.org/r/20240222011129.79241-1-curtis.klein@hpe.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
ds1511_rtc_read_alarm was useless as it is only called at boot time so
the alarm members of pdata have not yet been set. Read the actual registers
so there is a chance to get a meaningful value.
Then, drop the alarm related members of pdata as they are not used anymore.
Link: https://lore.kernel.org/r/20240227230431.1837717-10-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
ds1511_rtc_update_alarm is called twice but one of the call is overkill as
it only has to enable or disable the alarm instead of updating all the alarm
registers. Merge it in its main call site and introduce a new finction to
enable or disable the alarm.
Link: https://lore.kernel.org/r/20240227230431.1837717-7-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
'days' is a s64 (from div_s64), and so should use a %lld specifier.
This was found by extending KUnit's assertion macros to use gcc's
__printf attribute.
Fixes: 1d1bb12a8b ("rtc: Improve performance of rtc_time64_to_tm(). Add tests.")
Signed-off-by: David Gow <davidgow@google.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The NCT3015Y-R and NCT3018Y-R use the same datasheet
but have different topologies as follows.
- Topology (Only 1st i2c can set TWO bit and HF bit)
In NCT3015Y-R,
rtc 1st i2c is connected to a host CPU
rtc 2nd i2c is connected to a BMC
In NCT3018Y-R,
rtc 1st i2c is connected to a BMC
rtc 2nd i2c is connected to a host CPU
In order to be compatible with NCT3015Y-R and NCT3018Y-R,
- In probe,
If part number is NCT3018Y-R, only set HF bit to 24-Hour format.
Else, do nothing
- In set_time,
If part number is NCT3018Y-R && TWO bit is 0,
change TWO bit to 1, and restore TWO bit after updating time.
Signed-off-by: Mia Lin <mimi05633@gmail.com>
Link: https://lore.kernel.org/r/20231113103807.1036978-2-mimi05633@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Replace of_match_node()->device_get_match_data() for
the data associated with device match.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240105145344.204453-3-biju.das.jz@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On some platforms (eg: RZ/{G2UL,Five} SMARC EVK), there is no IRQ
populated by default. Add irq optional support.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240105145344.204453-2-biju.das.jz@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Clang warns (or errors with CONFIG_WERROR=y):
drivers/rtc/rtc-max31335.c:211:36: error: use of logical '||' with constant operand [-Werror,-Wconstant-logical-operand]
211 | if (reg == MAX31335_TEMP_DATA_MSB || MAX31335_TEMP_DATA_LSB)
| ^ ~~~~~~~~~~~~~~~~~~~~~~
drivers/rtc/rtc-max31335.c:211:36: note: use '|' for a bitwise operation
211 | if (reg == MAX31335_TEMP_DATA_MSB || MAX31335_TEMP_DATA_LSB)
| ^~
| |
1 error generated.
This clearly should be a comparison against reg. Fix the comparison so
that max31335_volatile_reg() does not always return true.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1980
Fixes: dedaf03b99 ("rtc: max31335: add driver support")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240117-rtc-max3133-fix-comparison-v1-1-91e98b29d564@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There is no race condition when accessing MAX31335_STATUS1 because it is
always about clearing the alarm interrupt bit.
Reviewed-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20240115232215.273374-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Prevent kernel-doc warnings by changing "/**" to common comment
format "/*" in non-kernel-doc comments:
drivers/rtc/rtc-ac100.c:103: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Clock controls for 3 clock output pins
drivers/rtc/rtc-ac100.c:382: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* RTC related bits
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: <linux-rtc@vger.kernel.org>
Link: https://lore.kernel.org/r/20240114231320.31437-1-rdunlap@infradead.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add power management support to the driver. This allows a SoC to wake
from suspend using the nINT provided by the RTC. Only register it as a
wakeup device if the interrupt is provided and handled.
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Link: https://lore.kernel.org/r/20231122181611.164792-1-eichest@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix the following warning when CONFIG_I2C is not set but CONFIG_SPI_MASTER
is set.
warning: 'ds3232_pm_ops' defined but not used [-Wunused-const-variable=]
'ds3232_pm_ops' is only used by rtc-ds3232 i2c driver, so move the device
PM callbacks inside #if IS_ENABLED(CONFIG_I2C).
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202311172325.33tTniaJ-lkp@intel.com/
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Link: https://lore.kernel.org/r/20231118092200.829808-1-akinobu.mita@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
TPS6594 PMIC is a MFD. This patch adds support for
the RTC found inside TPS6594 family of PMIC.
Alarm is also supported.
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20231107094701.2223486-1-eblanc@baylibre.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The ma35d1 rtc controller provides real-time and calendar messaging
capabilities. It supports programmable time tick and alarm match
interrupts. The time and calendar messages are expressed in BCD format.
This driver supports the built-in rtc controller of the ma35d1. It
enables setting and reading the rtc time and configuring and reading
the rtc alarm.
Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
Link: https://lore.kernel.org/r/20230925070251.28-4-ychuang570808@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Specs don't say anything about UIP being cleared within 10ms. They
only say that UIP won't occur for another 244uS. If a long NMI occurs
while UIP is still updating it might not be possible to get valid
data in 10ms.
This has been observed in the wild that around s2idle some calls can
take up to 480ms before UIP is clear.
Adjust callers from outside an interrupt context to wait for up to a
1s instead of 10ms.
Cc: <stable@vger.kernel.org> # 6.1.y
Fixes: ec5895c0f2 ("rtc: mc146818-lib: extract mc146818_avoid_UIP")
Reported-by: Carsten Hatger <xmb8dsv4@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217626
Tested-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Reviewed-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Acked-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20231128053653.101798-5-mario.limonciello@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The UIP timeout is hardcoded to 10ms for all RTC reads, but in some
contexts this might not be enough time. Add a timeout parameter to
mc146818_get_time() and mc146818_get_time_callback().
If UIP timeout is configured by caller to be >=100 ms and a call
takes this long, log a warning.
Make all callers use 10ms to ensure no functional changes.
Cc: <stable@vger.kernel.org> # 6.1.y
Fixes: ec5895c0f2 ("rtc: mc146818-lib: extract mc146818_avoid_UIP")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Reviewed-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Acked-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Link: https://lore.kernel.org/r/20231128053653.101798-4-mario.limonciello@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When mc146818_avoid_UIP() fails to return a valid value, this is because
UIP didn't clear in the timeout period. Adjust the return code in this
case to -ETIMEDOUT.
Tested-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Reviewed-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Acked-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: <stable@vger.kernel.org>
Fixes: cdedc45c57 ("rtc: cmos: avoid UIP when reading alarm time")
Fixes: cd17420ebe ("rtc: cmos: avoid UIP when writing alarm time")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20231128053653.101798-3-mario.limonciello@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
mc146818_get_time() calls mc146818_avoid_UIP() to avoid fetching the
time while RTC update is in progress (UIP). When this fails, the return
code is -EIO, but actually there was no IO failure.
The reason for the return from mc146818_avoid_UIP() is that the UIP
wasn't cleared in the time period. Adjust the return code to -ETIMEDOUT
to match the behavior.
Tested-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Reviewed-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Acked-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: <stable@vger.kernel.org>
Fixes: 2a61b0ac54 ("rtc: mc146818-lib: refactor mc146818_get_time")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20231128053653.101798-2-mario.limonciello@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Intel systems > 2015 have been configured to use ACPI alarm instead
of HPET to avoid s2idle issues.
Having HPET programmed for wakeup causes problems on AMD systems with
s2idle as well.
One particular case is that the systemd "SuspendThenHibernate" feature
doesn't work properly on the Framework 13" AMD model. Switching to
using ACPI alarm fixes the issue.
Adjust the quirk to apply to AMD/Hygon systems from 2021 onwards.
This matches what has been tested and is specifically to avoid potential
risk to older systems.
Cc: <stable@vger.kernel.org> # 6.1+
Reported-by: <alvin.zhuge@gmail.com>
Reported-by: <renzhamin@gmail.com>
Closes: https://github.com/systemd/systemd/issues/24279
Reported-by: Kelvie Wong <kelvie@kelvie.ca>
Closes: https://community.frame.work/t/systemd-suspend-then-hibernate-wakes-up-after-5-minutes/39392
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20231106162310.85711-1-mario.limonciello@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Subsytem:
- convert platform drivers to remove_new
- prevent modpost warnings for unremovable platform drivers
New driver:
- Mstar SSD202D
Drivers:
- brcmstb-waketimer: support level alarm_irq
- ep93xx: add DT support
- rtc7301: support byte-addressed IO
-----BEGIN PGP SIGNATURE-----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=4rbF
-----END PGP SIGNATURE-----
Merge tag 'rtc-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"There is a new driver for the RTC of the Mstar SSD202D SoC. The
rtc7301 driver gains support for byte addresses to support the
USRobotics USR8200. Then we have many non user visible changes and
typo fixes.
Summary:
Subsytem:
- convert platform drivers to remove_new
- prevent modpost warnings for unremovable platform drivers
New driver:
- Mstar SSD202D
Drivers:
- brcmstb-waketimer: support level alarm_irq
- ep93xx: add DT support
- rtc7301: support byte-addressed IO"
* tag 'rtc-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (28 commits)
dt-bindings: rtc: Add Mstar SSD202D RTC
rtc: Add support for the SSD202D RTC
rtc: at91rm9200: annotate at91_rtc_remove with __exit again
dt-bindings: rtc: microcrystal,rv3032: Document wakeup-source property
dt-bindings: rtc: pcf8523: Convert to YAML
dt-bindings: rtc: mcp795: move to trivial-rtc
rtc: ep93xx: add DT support for Cirrus EP93xx
dt-bindings: rtc: Add Cirrus EP93xx
dt-bindings: rtc: pcf2123: convert to YAML
rtc: efi: fixed typo in efi_procfs()
rtc: omap: Use device_get_match_data()
rtc: pcf85363: fix wrong mask/val parameters in regmap_update_bits call
rtc: rtc7301: Support byte-addressed IO
rtc: rtc7301: Rewrite bindings in schema
rtc: sh: Convert to platform remove callback returning void
rtc: pxa: Convert to platform remove callback returning void
rtc: mv: Convert to platform remove callback returning void
rtc: imxdi: Convert to platform remove callback returning void
rtc: at91rm9200: Convert to platform remove callback returning void
rtc: pcap: Drop no-op remove function
...
Binding for fixed NVMEM cells defined directly as NVMEM device subnodes
has been deprecated. It has been replaced by the "fixed-layout" NVMEM
layout binding.
New syntax is meant to be clearer and should help avoiding imprecise
bindings.
NVMEM subsystem already supports the new binding. It should be a good
idea to limit support for old syntax to existing drivers that actually
support & use it (we can't break backward compatibility!). That way we
additionally encourage new bindings & drivers to ignore deprecated
binding.
It wasn't clear (to me) if rtc and w1 code actually uses old syntax
fixed cells. I enabled them to don't risk any breakage.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
[for meson-{efuse,mx-efuse}.c]
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[for mtk-efuse.c, nvmem/core.c, nvmem-provider.h]
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
[MT8192, MT8195 Chromebooks]
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
[for microchip-otpc.c]
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
[SAMA7G5-EK]
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231020105545.216052-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer SigmaStar SSD202D SoCs contain a Real Time Clock, capable of
running while the system is sleeping (battery powered), this is not the
case with the other RTC on older SoCs. This adds basic support for this
RTC block.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Co-developed-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20230913151606.69494-2-romain.perier@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
After the first check of the value of the "eft" variable
it does not change, it is obvious that a copy-paste
error was made here and the value of variable "alm"
should be checked here.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 501385f2a7 ("rtc: efi: add efi_procfs in efi_rtc_ops")
Signed-off-by: Maxim Korotkov <korotkov.maxim.s@gmail.com>
Link: https://lore.kernel.org/r/20231006090444.306729-1-korotkov.maxim.s@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231009211356.3242037-12-robh@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The current implementation passes PIN_IO_INTA_OUT (2) as a mask and
PIN_IO_INTAPM (GENMASK(1, 0)) as a value.
Swap the variables to assign mask and value the right way.
This error was first introduced with the alarm support. For better or
worse it worked as expected because 0x02 was applied as a mask to 0x03,
resulting 0x02 anyway. This will of course not work for any other value.
Fixes: e5aac267a1 ("rtc: pcf85363: add alarm support")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20231013-topic-pcf85363_regmap_update_bits-v1-1-c454f016f71f@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The old RTC7301 driver in OpenWrt used byte access, but the
current mainline Linux driver uses 32bit word access.
Make this configurable using device properties using the
standard property "reg-io-width" in e.g. device tree.
This is needed for the USRobotics USR8200 which has the
chip connected using byte accesses.
Debugging and testing by Howard Harte.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Link: https://lore.kernel.org/r/20231010-rtc-7301-regwidth-v3-2-ade586b62794@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231002080529.2535610-13-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231002080529.2535610-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231002080529.2535610-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231002080529.2535610-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231002080529.2535610-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
A remove callback that just returns 0 is equivalent to no callback at
all as can be seen in platform_remove(). So simplify accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231002080529.2535610-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As described in the added code comment, a reference to .exit.text is ok
for drivers registered via module_platform_driver_probe(). Make this
explicit to prevent a section mismatch warning.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231002080529.2535610-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As described in the added code comment, a reference to .exit.text is ok
for drivers registered via module_platform_driver_probe(). Make this
explicit to prevent a section mismatch warning.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231002080529.2535610-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As described in the added code comment, a reference to .exit.text is ok
for drivers registered via module_platform_driver_probe(). Make this
explicit to prevent a section mismatch warning.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231002080529.2535610-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As described in the added code comment, a reference to .exit.text is ok
for drivers registered via module_platform_driver_probe(). Make this
explicit to prevent a section mismatch warning.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231002080529.2535610-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As described in the added code comment, a reference to .exit.text is ok
for drivers registered via module_platform_driver_probe(). Make this
explicit to prevent a section mismatch warning.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231002080529.2535610-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Some devices (e.g. BCM72112) use an alarm_irq interrupt that is
connected to a level interrupt controller rather than an edge
interrupt controller. In this case, the interrupt cannot be left
enabled by the irq handler while preserving the hardware wake-up
signal on wake capable devices or an interrupt storm will occur.
The alarm_expired flag is introduced to allow the disabling of
the interrupt when an alarm expires and to support balancing the
calls to disable_irq() and enable_irq() in accordance with the
existing design.
Fixes: 24304a8715 ("rtc: brcmstb-waketimer: allow use as non-wake alarm")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230830224747.1663044-1-opendmb@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Subsystem:
- Add a way for drivers to tell the core the supported alarm range is smaller
than the date range. This is not used yet but will be useful for the
alarmtimers in the next release.
- fix Wvoid-pointer-to-enum-cast warnings
- remove redundant of_match_ptr()
- stop warning for invalid alarms when the alarm is disabled
Drivers:
- isl12022: allow setting the trip level for battery level detection
- pcf2127: add support for PCF2131 and multiple timestamps
- stm32: time precision improvement, many fixes
- twl: NVRAM support
-----BEGIN PGP SIGNATURE-----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=4kkJ
-----END PGP SIGNATURE-----
Merge tag 'rtc-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- Add a way for drivers to tell the core the supported alarm range is
smaller than the date range. This is not used yet but will be
useful for the alarmtimers in the next release.
- fix Wvoid-pointer-to-enum-cast warnings
- remove redundant of_match_ptr()
- stop warning for invalid alarms when the alarm is disabled
Drivers:
- isl12022: allow setting the trip level for battery level detection
- pcf2127: add support for PCF2131 and multiple timestamps
- stm32: time precision improvement, many fixes
- twl: NVRAM support"
* tag 'rtc-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (73 commits)
dt-bindings: rtc: ds3231: Remove text binding
rtc: wm8350: remove unnecessary messages
rtc: twl: remove unnecessary messages
rtc: sun6i: remove unnecessary message
rtc: stop warning for invalid alarms when the alarm is disabled
rtc: twl: add NVRAM support
rtc: pcf85363: Allow to wake up system without IRQ
rtc: m48t86: add DT support for m48t86
dt-bindings: rtc: Add ST M48T86
rtc: pcf2127: remove useless check
rtc: rzn1: Report maximum alarm limit to rtc core
rtc: ds1305: Report maximum alarm limit to rtc core
rtc: tps6586x: Report maximum alarm limit to rtc core
rtc: cmos: Report supported alarm limit to rtc infrastructure
rtc: cros-ec: Detect and report supported alarm window size
rtc: Add support for limited alarm timer offsets
rtc: isl1208: Fix incorrect logic in isl1208_set_xtoscb()
MAINTAINERS: remove obsolete pattern in RTC SUBSYSTEM section
rtc: tps65910: Remove redundant dev_warn() and do not check for 0 return after calling platform_get_irq()
rtc: omap: Do not check for 0 return after calling platform_get_irq()
...
