The previous attempt to augment carrier_down (see Link)
was not met with much enthusiasm so let's do the simple
thing of exposing what some devices already maintain.
Add a common ethtool statistic for link going down.
Currently users have to maintain per-driver mapping
to extract the right stat from the vendor-specific ethtool -S
stats. carrier_down does not fit the bill because it counts
a lot of software related false positives.
Add the statistic to the extended link state API to steer
vendors towards implementing all of it.
Implement for bnxt and all Linux-controlled PHYs. mlx5 and (possibly)
enic also have a counter for this but I leave the implementation
to their maintainers.
Link: https://lore.kernel.org/r/20220520004500.2250674-1-kuba@kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20221104190125.684910-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This adds support for rate matching (also known as rate adaptation) to
the phy subsystem. The general idea is that the phy interface runs at
one speed, and the MAC throttles the rate at which it sends packets to
the link speed. There's a good overview of several techniques for
achieving this at [1]. This patch adds support for three: pause-frame
based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and
2BASE-TL), and open-loop-based (such as in 10GBASE-W).
This patch makes a few assumptions and a few non assumptions about the
types of rate matching available. First, it assumes that different phys
may use different forms of rate matching. Second, it assumes that phys
can use rate matching for any of their supported link speeds (e.g. if a
phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T).
Third, it does not assume that all interface modes will use the same
form of rate matching. Fourth, it does not assume that all phy devices
will support rate matching (even if some do). Relaxing or strengthening
these (non-)assumptions could result in a different API. For example, if
all interface modes were assumed to use the same form of rate matching,
then a bitmask of interface modes supportting rate matching would
suffice.
For some better visibility into the process, the current rate matching
mode is exposed as part of the ethtool ksettings. For the moment, only
read access is supported. I'm not sure what userspace might want to
configure yet (disable it altogether, disable just one mode, specify the
mode to use, etc.). For the moment, since only pause-based rate
adaptation support is added in the next few commits, rate matching can
be disabled altogether by adjusting the advertisement.
802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and
"rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls
this feature "rate adaptation". I chose "rate matching" because it is
shorter, and because Russell doesn't think "adaptation" is correct in this
context.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon system sleep, mdio_bus_phy_suspend() stops the phy_state_machine(),
but subsequent interrupts may retrigger it:
They may have been left enabled to facilitate wakeup and are not
quiesced until the ->suspend_noirq() phase. Unwanted interrupts may
hence occur between mdio_bus_phy_suspend() and dpm_suspend_noirq(),
as well as between dpm_resume_noirq() and mdio_bus_phy_resume().
Retriggering the phy_state_machine() through an interrupt is not only
undesirable for the reason given in mdio_bus_phy_suspend() (freezing it
midway with phydev->lock held), but also because the PHY may be
inaccessible after it's suspended: Accesses to USB-attached PHYs are
blocked once usb_suspend_both() clears the can_submit flag and PHYs on
PCI network cards may become inaccessible upon suspend as well.
Amend phy_interrupt() to avoid triggering the state machine if the PHY
is suspended. Signal wakeup instead if the attached net_device or its
parent has been configured as a wakeup source. (Those conditions are
identical to mdio_bus_phy_may_suspend().) Postpone handling of the
interrupt until the PHY has resumed.
Before stopping the phy_state_machine() in mdio_bus_phy_suspend(),
wait for a concurrent phy_interrupt() to run to completion. That is
necessary because phy_interrupt() may have checked the PHY's suspend
status before the system sleep transition commenced and it may thus
retrigger the state machine after it was stopped.
Likewise, after re-enabling interrupt handling in mdio_bus_phy_resume(),
wait for a concurrent phy_interrupt() to complete to ensure that
interrupts which it postponed are properly rerun.
The issue was exposed by commit 1ce8b37241 ("usbnet: smsc95xx: Forward
PHY interrupts to PHY driver to avoid polling"), but has existed since
forever.
Fixes: 541cd3ee00 ("phylib: Fix deadlock on resume")
Link: https://lore.kernel.org/netdev/a5315a8a-32c2-962f-f696-de9a26d30091@samsung.com/
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org # v2.6.33+
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/b7f386d04e9b5b0e2738f0125743e30676f309ef.1656410895.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This fixes the following error caused by a race condition between
phydev->adjust_link() and a MDIO transaction in the phy interrupt
handler. The issue was reproduced with the ethernet FEC driver and a
micrel KSZ9031 phy.
[ 146.195696] fec 2188000.ethernet eth0: MDIO read timeout
[ 146.201779] ------------[ cut here ]------------
[ 146.206671] WARNING: CPU: 0 PID: 571 at drivers/net/phy/phy.c:942 phy_error+0x24/0x6c
[ 146.214744] Modules linked in: bnep imx_vdoa imx_sdma evbug
[ 146.220640] CPU: 0 PID: 571 Comm: irq/128-2188000 Not tainted 5.18.0-rc3-00080-gd569e86915b7 #9
[ 146.229563] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 146.236257] unwind_backtrace from show_stack+0x10/0x14
[ 146.241640] show_stack from dump_stack_lvl+0x58/0x70
[ 146.246841] dump_stack_lvl from __warn+0xb4/0x24c
[ 146.251772] __warn from warn_slowpath_fmt+0x5c/0xd4
[ 146.256873] warn_slowpath_fmt from phy_error+0x24/0x6c
[ 146.262249] phy_error from kszphy_handle_interrupt+0x40/0x48
[ 146.268159] kszphy_handle_interrupt from irq_thread_fn+0x1c/0x78
[ 146.274417] irq_thread_fn from irq_thread+0xf0/0x1dc
[ 146.279605] irq_thread from kthread+0xe4/0x104
[ 146.284267] kthread from ret_from_fork+0x14/0x28
[ 146.289164] Exception stack(0xe6fa1fb0 to 0xe6fa1ff8)
[ 146.294448] 1fa0: 00000000 00000000 00000000 00000000
[ 146.302842] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 146.311281] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 146.318262] irq event stamp: 12325
[ 146.321780] hardirqs last enabled at (12333): [<c01984c4>] __up_console_sem+0x50/0x60
[ 146.330013] hardirqs last disabled at (12342): [<c01984b0>] __up_console_sem+0x3c/0x60
[ 146.338259] softirqs last enabled at (12324): [<c01017f0>] __do_softirq+0x2c0/0x624
[ 146.346311] softirqs last disabled at (12319): [<c01300ac>] __irq_exit_rcu+0x138/0x178
[ 146.354447] ---[ end trace 0000000000000000 ]---
With the FEC driver phydev->adjust_link() calls fec_enet_adjust_link()
calls fec_stop()/fec_restart() and both these function reset and
temporary disable the FEC disrupting any MII transaction that
could be happening at the same time.
fec_enet_adjust_link() and phy_read() can be running at the same time
when we have one additional interrupt before the phy_state_machine() is
able to terminate.
Thread 1 (phylib WQ) | Thread 2 (phy interrupt)
|
| phy_interrupt() <-- PHY IRQ
| handle_interrupt()
| phy_read()
| phy_trigger_machine()
| --> schedule phylib WQ
|
|
phy_state_machine() |
phy_check_link_status() |
phy_link_change() |
phydev->adjust_link() |
fec_enet_adjust_link() |
--> FEC reset | phy_interrupt() <-- PHY IRQ
| phy_read()
|
Fix this by acquiring the phydev lock in phy_interrupt().
Link: https://lore.kernel.org/all/20220422152612.GA510015@francesco-nb.int.toradex.com/
Fixes: c974bdbc3e ("net: phy: Use threaded IRQ, to allow IRQ from sleeping devices")
cc: <stable@vger.kernel.org>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220506060815.327382-1-francesco.dolcini@toradex.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stop using the helpers to construct a special phy address which
indicates C45. Instead use the C45 accessors, which will call the
busses C45 specific read/write API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As reported by Zhang there's a small issue if in forced mode the duplex
mode changes with the link staying up [0]. In this case the MAC isn't
notified about the change.
The proposed patch relies on the phylib state machine and ignores the
fact that there are drivers that uses phylib but not the phylib state
machine. So let's don't change the behavior for such drivers and fix
it w/o re-adding state PHY_FORCING for the case that phylib state
machine is used.
[0] https://lore.kernel.org/netdev/a5c26ffd-4ee4-a5e6-4103-873208ce0dc5@huawei.com/T/
Fixes: 2bd229df5e ("net: phy: remove state PHY_FORCING")
Reported-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Tested-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/7b8b9456-a93f-abbc-1dc5-a2c2542f932c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a race condition where the PHY state machine can change
members of the phydev structure at the same time userspace requests a
change via ethtool. To prevent this, have phy_ethtool_ksettings_set
take the PHY lock.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Reported-by: Walter Stoll <Walter.Stoll@duagon.com>
Suggested-by: Walter Stoll <Walter.Stoll@duagon.com>
Tested-by: Walter Stoll <Walter.Stoll@duagon.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split phy_start_aneg into a wrapper which takes the PHY lock, and a
helper doing the real work. This will be needed when
phy_ethtook_ksettings_set takes the lock.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows it to make use of a helper which assume the PHY is already
locked.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY structure should be locked while copying information out if
it, otherwise there is no guarantee of self consistency. Without the
lock the PHY state machine could be updating the structure.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following format issues:
1. open brace '{' following function definitions should go to the next
line.
2. braces {} are not necessary for single line statements.
3. else should follow close brace '}'.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case phy_state_machine() works on top of USB device, we can get -ENODEV
at any point. So, be less noisy if device was removed.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of loopback, in most cases we need to disable autoneg support
and force some speed configuration. Otherwise, depending on currently
active auto negotiated link speed, the loopback may or may not work.
This patch was tested with following PHYs: TJA1102, KSZ8081, KSZ9031,
AT8035, AR9331.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If phy uses generic driver and autoneg is on, enter command
"ethtool -s eth0 speed 50" will not change phy speed actually, but
command "ethtool eth0" shows speed is 50Mb/s because phydev->speed
has been set to 50 and no update later.
And duplex setting has same problem too.
However, if autoneg is on, phy only changes speed and duplex according to
phydev->advertising, but not phydev->speed and phydev->duplex. So in this
case, phydev->speed and phydev->duplex don't need to be set in function
phy_ethtool_ksettings_set() if autoneg is on.
Fixes: 51e2a3846e ("PHY: Avoid unnecessary aneg restarts")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some internal PHY's have their events like link change reported by the
MAC interrupt. We have PHY_IGNORE_INTERRUPT to deal with this scenario.
I'm not too happy with this name. We don't ignore interrupts, typically
there is no interrupt exposed at a PHY level. So let's rename it to
PHY_MAC_INTERRUPT. This is in line with phy_mac_interrupt(), which is
called from the MAC interrupt handler to handle PHY events.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, PORT_MII is reported in the ethtool ops. This is odd
because it is an interface between the MAC and the PHY and no external
port. Some network card drivers will overwrite the port to twisted pair
or fiber, though. Even worse, the MDI/MDIX setting is only used by
ethtool if the port is twisted pair.
Set the port to PORT_TP by default because most PHY drivers are copper
ones. If there is fibre support and it is enabled, the PHY driver will
set it to PORT_FIBRE.
This will change reporting PORT_MII to either PORT_TP or PORT_FIBRE;
except for the genphy fallback driver.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to lockdep_assert_held(_once), similar to what is being done
in other subsystems. One advantage is that there's zero runtime
overhead if lockdep support isn't enabled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/ccc40b9d-8ee0-43a1-5009-2cc95ca79c85@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that all the PHY drivers have been migrated to directly implement
the generic .handle_interrupt() callback for a seamless support of
shared IRQs and all the .config_inter() implementations clear any
pending interrupts, we can safely remove the two callbacks.
With this patch, phylib has a proper support for shared IRQs (and not
just for multi-PHY devices. A PHY driver must implement both the
.handle_interrupt() and .config_intr() callbacks for the IRQs to be
actually used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some functions have different names between their prototypes
and the kernel-doc markup.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These functions are currently used by phy_interrupt() to either signal
an error condition or to trigger the link state machine. In an attempt
to actually support shared PHY IRQs, export these two functions so that
the actual PHY drivers can use them.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add kerneldoc for the core PHY data structures, a few inline functions
and exported functions which are not already documented.
v2
Typos
g/phy/PHY/s
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When phy_is_started() was added to catch incorrect PHY states,
phy_stop() would not be qualified against PHY_DOWN. It is possible to
reach that state when the PHY driver has been unbound and the network
device is then brought down.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have moved the PHY ethtool statistics to be dynamically
registered, we no longer need to inline those for ethtool. This used to
be done to avoid cross symbol referencing and allow ethtool to be
decoupled from PHYLIB entirely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We face an issue with rtl8211f, a pin is shared between INTB and PMEB,
and the PHY Register Accessible Interrupt is enabled by default, so
the INTB/PMEB pin is always active in polling mode case.
As Heiner pointed out "I was thinking about calling
phy_disable_interrupts() in phy_init_hw(), to have a defined init
state as we don't know in which state the PHY is if the PHY driver is
loaded. We shouldn't assume that it's the chip power-on defaults, BIOS
or boot loader could have changed this. Or in case of dual-boot
systems the other OS could leave the PHY in whatever state."
Make phy_disable_interrupts() non-static so that it could be used in
phy_init_hw() to have a defined init state.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.
If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a recurring pattern throughout some of the PHY code converting
a devad and regnum to our packed clause 45 representation. Rather than
having this scattered around the code, let's put a common translation
function in mdio.h, and provide some register accessors.
Convert the phylib core, phylink, bcm87xx and cortina to use these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function was introduced to allow for different handling of
link up and link down events particularly with regard to the
netif_carrier. The third argument do_carrier allowed the flag to
be left unchanged.
Since then the phylink has introduced an implementation that
completely ignores the third parameter since it never wants to
change the flag and the phylib always sets the third parameter
to true so the flag is always changed.
Therefore the third argument (i.e. do_carrier) is no longer
necessary and can be removed. This also means that the phylib
phy_link_down() function no longer needs its second argument.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_restart_aneg() enables aneg in the PHY. That's not what we want
if phydev->autoneg is disabled. In this case still update EEE
advertisement register, but don't enable aneg and don't trigger an
aneg restart.
Fixes: f75abeb833 ("net: phy: restart phy autonegotiation after EEE advertisment change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since running a cable test is disruptive, put the interface into
operative state testing while the test is running.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide infrastructure for PHY drivers to report the cable test
results. A netlink skb is associated to the phydev. Helpers will be
added which can add results to this skb. Once the test has finished
the results are sent to user space.
When netlink ethtool is not part of the kernel configuration stubs are
provided. It is also impossible to trigger a cable test, so the error
code returned by the alloc function is of no consequence.
v2:
Include the status complete in the netlink notification message
v4:
Replace -EINVAL with -EMSGSIZE
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some PHYs are not capable of generating interrupts when a cable test
finished. They do however support interrupts for normal operations,
like link up/down. As such, the PHY state machine would normally not
poll the PHY.
Add support for indicating the PHY state machine must poll the PHY
when performing a cable test.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Running a cable test is desruptive to normal operation of the PHY and
can take a 5 to 10 seconds to complete. The RTNL lock cannot be held
for this amount of time, and add a new state to the state machine for
running a cable test.
The driver is expected to implement two functions. The first is used
to start a cable test. Once the test has started, it should return.
The second function is called once per second, or on interrupt to
check if the cable test is complete, and to allow the PHY to report
the status.
v2:
Rename phy_cable_test_abort to phy_abort_cable_test
Return different extack when already running test
Use phy_init_hw() to reset the PHY
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of
auto-negotiation support, we needed to be able to configure the
MASTER-SLAVE role of the port manually or from an application in user
space.
The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to
force MASTER or SLAVE role. See IEEE 802.3-2018:
22.2.4.3.7 MASTER-SLAVE control register (Register 9)
22.2.4.3.8 MASTER-SLAVE status register (Register 10)
40.5.2 MASTER-SLAVE configuration resolution
45.2.1.185.1 MASTER-SLAVE config value (1.2100.14)
45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)
The MASTER-SLAVE role affects the clock configuration:
-------------------------------------------------------------------------------
When the PHY is configured as MASTER, the PMA Transmit function shall
source TX_TCLK from a local clock source. When configured as SLAVE, the
PMA Transmit function shall source TX_TCLK from the clock recovered from
data stream provided by MASTER.
iMX6Q KSZ9031 XXX
------\ /-----------\ /------------\
| | | | |
MAC |<----RGMII----->| PHY Slave |<------>| PHY Master |
|<--- 125 MHz ---+-<------/ | | \ |
------/ \-----------/ \------------/
^
\-TX_TCLK
-------------------------------------------------------------------------------
Since some clock or link related issues are only reproducible in a
specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial
to provide generic (not 100BASE-T1 specific) interface to the user space
for configuration flexibility and trouble shooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far PHY drivers have to check whether a downshift occurred to be
able to notify the user. To make life of drivers authors a little bit
easier move the downshift notification to phylib. phy_check_downshift()
compares the highest mutually advertised speed with the actual value
of phydev->speed (typically read by the PHY driver from a
vendor-specific register) to detect a downshift.
v2:
- Add downshift hint to phy_print_status
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
did_interrupt() clears the interrupt, therefore handle_interrupt() can
not check which event triggered the interrupt. To overcome this
constraint and allow more flexibility for customer interrupt handlers,
let's decouple handle_interrupt() from parts of the phylib interrupt
handling. Custom interrupt handlers now have to implement the
did_interrupt() functionality in handle_interrupt() if needed.
Fortunately we have just one custom interrupt handler so far (in the
mscc PHY driver), convert it to the changed API.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On all PHY drivers that implement did_interrupt() reading the interrupt
status bits clears them. This means we may loose an interrupt that
is triggered between calling did_interrupt() and phy_clear_interrupt().
As part of the fix make it a requirement that did_interrupt() clears
the interrupt.
The Fixes tag refers to the first commit where the patch applies
cleanly.
Fixes: 49644e68f4 ("net: phy: add callback for custom interrupt handler to struct phy_driver")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new version of phy_do_ioctl that doesn't check whether net_device
is running. It will typically be used if suitable drivers attach the
PHY in probe already.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We just added phy_do_ioctl, but it turned out that we need another
version of this function that doesn't check whether net_device is
running. So rename phy_do_ioctl to phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of network drivers has the same glue code to use phy_mii_ioctl
as ndo_do_ioctl handler. So let's add such a generic ndo_do_ioctl
handler to phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the stack supports time stamping in PHY devices. However,
there are newer, non-PHY devices that can snoop an MII bus and provide
time stamps. In order to support such devices, this patch introduces
a new interface to be used by both PHY and non-PHY devices.
In addition, the one and only user of the old PHY time stamping API is
converted to the new interface.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no users of phy_ethtool_sset() in the kernel anymore, and
as of commit 3c1bcc8614 ("net: ethernet: Convert phydev advertize
and supported from u32 to link mode"), the implementation is slightly
buggy - it doesn't correctly check the masked advertising mask as it
used to.
Remove it, and update the phy documentation to refer to its replacement
function.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Add core phylib help for supporting SFP sockets on PHYs. This provides
a mechanism to inform the SFP layer about PHY up/down events, and also
unregister the SFP bus when the PHY is going away.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers just call phy_ethtool_ksettings_set() to set the
links, for those phy drivers that use genphy_read_status(), if
autoneg is on, and the link is up, than execute "ethtool -s
ethx autoneg on" will cause "link partner" information disappear.
The call trace is phy_ethtool_ksettings_set()->phy_start_aneg()
->linkmode_zero(phydev->lp_advertising)->genphy_read_status(),
the link didn't change, so genphy_read_status() just return, and
phydev->lp_advertising is zero now.
This patch moves the clear operation of lp_advertising from
phy_start_aneg() to genphy_read_lpa()/genphy_c45_read_lpa(), and
if autoneg on and autoneg not complete, just clear what the
generic functions care about.
Fixes: 88d6272aca ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When userspace writes to the MII_ADVERTISE register, we update phylib's
advertising mask and trigger a renegotiation. However, writing to the
MII_CTRL1000 register, which contains the gigabit advertisement, does
neither. This can lead to phylib's copy of the advertisement becoming
de-synced with the values in the PHY register set, which can result in
incorrect negotiation resolution.
Fixes: 5502b218e0 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
While running stmmac selftests I found that in my 1G setup some tests
were failling when running with PHY loopback enabled.
It looks like when loopback is enabled the PHY will report that Link is
down even though there is a valid connection.
As in loopback mode the data will not be sent anywhere we can bypass the
logic of checking if Link is valid thus saving unecessary reads.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ethernet drivers may call phy_start() and phy_stop() from
ndo_open() and ndo_close() respectively.
When network cable is unconnected, and operate like below:
step 1: ifconfig ethX up -> ndo_open -> phy_start ->start
autoneg, and phy is no link.
step 2: ifconfig ethX down -> ndo_close -> phy_stop -> just stop
phy state machine.
This patch forces phy suspend even phydev->link is off.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 34786005ec ("net: phy: prevent PHYs w/o Clause 22 regs from calling
genphy_config_aneg") introduced a check that aborts phy_config_aneg()
if the phy is a C45 phy.
This causes phy_state_machine() to call phy_error() so that the phy
ends up in PHY_HALTED state.
Instead of returning -EOPNOTSUPP, call genphy_c45_config_aneg()
(analogous to the C22 case) so that the state machine can run
correctly.
genphy_c45_config_aneg() closely resembles mv3310_config_aneg()
in drivers/net/phy/marvell10g.c, excluding vendor specific
configurations for 1000BaseT.
Fixes: 22b56e8270 ("net: phy: replace genphy_10g_driver with genphy_c45_driver")
Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far phy_speed_down/up can be used up to 1Gbps only. Remove this
restriction by using new helper __phy_speed_down. New member adv_old
in struct phy_device is used by phy_speed_up to restore the advertised
modes before calling phy_speed_down. Don't simply advertise what is
supported because a user may have intentionally removed modes from
advertisement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
linkmode_mod_bit is introduced as a helper function to set/clear
bits in a linkmode.
Replace the if else code structure with a call to the helper
linkmode_mod_bit.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the early days of phylib we had a functionality that changed to the
next lower speed in fixed mode if no link was established after a
certain period of time. This functionality has been removed years ago,
and state PHY_FORCING isn't needed any longer. Instead we can go from
UP to RUNNING or NOLINK directly (same as in autoneg mode).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow userspace to generate Clause 45 MII access cycles via phylib.
This is useful for tools such as mii-diag to be able to inspect Clause
45 PHYs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We face the issue that link change interrupt and link status may be
reported by different PHY layers. As a result the link change
interrupt may occur before the link status changes.
Export phy_queue_state_machine to allow PHY drivers to specify a
delay between link status change interrupt and link status check.
v2:
- change jiffies parameter type to unsigned long
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylib interrupt handler handles link change events only currently.
However PHY drivers may want to use other interrupt sources too,
e.g. to report temperature monitoring events. Therefore add a callback
to struct phy_driver allowing PHY drivers to implement a custom
interrupt handler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Suggested-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a step towards allowing PHY drivers to handle more
interrupt sources than just link change. E.g. several PHY's have
built-in temperature monitoring and can raise an interrupt if a
temperature threshold is exceeded. We may be interested in such
interrupts also if the phylib state machine isn't started.
Therefore move enabling interrupts to phy_request_interrupt().
v2:
- patch added to series
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we report symmetric pause only, and we don't consider the local
pause capabilities. Let's properly consider local and remote
capabilities, and report also asymmetric pause.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I got an interesting report [0] that after resuming from hibernation
the link has 100Mbps instead of 1Gbps. Reason is that another OS has
been used whilst Linux was hibernated. And this OS speeds down the link
due to WoL. Therefore, when resuming, we shouldn't expect that what
the PHY advertises is what it did when hibernating.
Easiest way to do this is removing state PHY_RESUMING. Instead always
go via PHY_UP that configures PHY advertisement.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202851
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_sanitize_settings() is called from phy_start_aneg() only, and only
if phydev->autoneg isn't set. Therefore the removed code does nothing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the Phy driver's link_change_notify callback is called
whenever the state machine is run (every second if polling), no matter
whether the state changed or not. This isn't needed and may confuse
users considering the name of the callback. Actually it contradicts
its kernel-doc description. Therefore let's change the behavior and
call this callback only in case of an actual state change.
This requires changes to the at803x and rockchip drivers.
at803x can be simplified so that it reacts on a state change to
PHY_NOLINK only.
The rockchip driver can also be much simplified. We simply re-init
the AFE/DSP registers whenever we change to PHY_RUNNING and speed
is 100Mbps. This causes very small overhead because we do this even
if the speed was 100Mbps already. But this is negligible and
I think justified by the much simpler code.
Changes are compile-tested only.
A little bit problematic seems to be to find somebody with the
hardware to test the changes to the two PHY drivers. See also [0].
David may be able to test the Rockchip driver.
[0] https://marc.info/?t=153782508800006&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have it let's use genphy_c45_aneg_done() in phy_aneg_done().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell reported the following race in the phylib state machine
(quoting from his mail):
if (phy_polling_mode(phydev) && phy_is_started(phydev))
phy_queue_state_machine(phydev, PHY_STATE_TIME);
state = PHY_UP
thread 0 thread 1
phy_disconnect()
+-phy_is_started()
phy_is_started() |
`-phy_stop()
+-phydev->state = PHY_HALTED
`-phy_stop_machine()
`-cancel_delayed_work_sync()
phy_queue_state_machine()
`-mod_delayed_work()
At this point, the phydev->state_queue() has been added back onto the
system workqueue despite phy_stop_machine() having been called and
cancel_delayed_work_sync() called on it.
Fix this by protecting the complete operation in thread 0.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Reported-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell suggested to remove the locking from phy_is_started() because
the read is atomic anyway and actually the locking may be more
misleading.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Suggested-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylib enables interrupts before phy_start() has been called, and if
we receive an interrupt in a non-started state, the interrupt handler
returns IRQ_NONE. This causes problems with at least one Marvell chip
as reported by Andrew.
Fix this by handling interrupts the same as in phy_mac_interrupt(),
basically always running the phylib state machine. It knows when it
has to do something and when not.
This change allows to handle interrupts gracefully even if they
occur in a non-started state.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the new MMD accessors.
v2:
- fix SoB
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we enable the interrupts in phy_start() we don't have to do it
before. Therefore remove enabling interrupts from phy_start_interrupts()
and rename this function to reflect the changed functionality.
v2:
- improve warning to clearly state that we fall back to polling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupts don't have to be enabled before calling phy_start().
Therefore let's enable them in phy_start(). In a subsequent step
we'll remove enabling interrupts from phy_connect_direct().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_start() should be called from states PHY_READY or PHY_HALTED only.
Check for this to detect misbehaving drivers. Also the state machine
should be started only when being called from one of the valid states.
Some more background:
For all invalid states phy_start() basically was a no-op. All it did
was triggering a state machine run, but for all "running" states the
poll loop was active anyway. And if called from PHY_DOWN, the state
machine does nothing.
v3:
- extended commit message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The state machine is a no-op before phy_start() has been called.
Therefore let's enable it in phy_start() only. In phy_start()
let's call phy_start_machine() instead of phy_trigger_machine().
phy_start_machine is an alias for phy_trigger_machine but it makes
clearer that we start the state machine here instead of just
triggering a run.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupts have been disabled in phy_stop() already. So we can remove
phy_stop_interrupts() and free the interrupt in phy_disconnect()
directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to the phylib state machine in phy_stop() just ensures that
the state machine isn't re-triggered, but a state machine call may
be scheduled already. So lets's call phy_stop_machine().
This also allows to get rid of the call to phy_stop_machine() in
phy_disconnect().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since recent changes to the phylib state machine state PHY_CHANGELINK
isn't used any longer. Therefore let's remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to and one shouldn't include asm/irq.h directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some time ago phydev_info() and friends have been added. They allow to
improve and simplify logging.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding checks to detect wrong usage of the phylib API we added
a check to phy_start_aneg() which is too strict. If the phylib
state machine is in state PHY_HALTED we should allow reconfiguring
and restarting aneg, and just don't touch the state.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far phy_error() silently stops the PHY state machine. If the network
driver doesn't inform about a MDIO error then the user may wonder why
his network is down. Let's print the stack trace to facilitate search
for the root cause of the error.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers phy_is_started() and __phy_is_started() to avoid open-coded
checks whether PHY has been started. To make the check easier move
PHY_HALTED before PHY_UP in enum phy_state. Further improvements:
phy_start_aneg():
Return -EBUSY and print warning if function is called from a non-started
state (DOWN, READY, HALTED). Better check because function is exported
and drivers may use it incorrectly.
phy_interrupt():
Return IRQ_NONE also if state is DOWN or READY. We should never receive
an interrupt in one of these states, but better play safe.
phy_stop():
Just return and print a warning if PHY is in a non-started state.
This warning should help to identify drivers with unbalanced calls to
phy_start() / phy_stop().
phy_state_machine():
Schedule state machine run only if PHY is in a started state.
E.g. if state is READY we don't need the state machine, it will be
started by phy_start().
v2:
- don't use __func__ within phy_warn_state
v3:
- use WARN() instead of printing error message to facilitate debugging
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the MII_ADVERTISE register is modified by the IOCTL handler,
phydev->advertising needs recalculating. Use the _mod_ variant of
mii_adv_to_linkmode_adv_t so that bits outside of the advertise
registers are not cleared.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far the two functions consider neither member eee_enabled nor
eee_active. Therefore network drivers have to do this in some kind
of glue code. I think this can be avoided.
Getting EEE parameters:
When not advertising any EEE mode, we can't consider EEE to be enabled.
Therefore interpret "EEE enabled" as "we advertise at least one EEE
mode". It's similar with "EEE active": interpret it as "EEE modes
advertised by both link partner have at least one mode in common".
Setting EEE parameters:
If eee_enabled isn't set, don't advertise any EEE mode and restart
aneg if needed to switch off EEE. If eee_enabled is set and
data->advertised is empty (e.g. because EEE was disabled), advertise
everything we support as default. This way EEE can easily switched
on/off by doing ethtool --set-eee <if> eee on/off, w/o any additional
parameters.
The changes to both functions shouldn't break any existing user.
Once the changes have been applied, at least some users can be
simplified.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change modified variable advertising from a u32 to a link mode
array and left the u32 zero comparison, so essential we now have an array
being compared to null which is not the intention. Fix this by using the
call to linkmode_empty to check if advertising is all zero.
Detected by CoverityScan, CID#1475424 ("Array compared against 0")
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert phy drivers to report the link partner advertised modes using
a linkmode bitmap. This allows them to report the higher speeds which
don't fit in a u32.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both states aren't used. Most likely they result from an idea that
never materialized. So remove them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that phy_mac_interrupt() doesn't call phy_change() any longer it's
called from phy_interrupt() only. Therefore phy_interrupt_is_valid()
returns true always and the check can be removed.
In case of PHY_HALTED phy_interrupt() bails out immediately,
therefore the second check for PHY_HALTED including the call to
phy_disable_interrupts() can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using phy_mac_interrupt() the irq number is set to
PHY_IGNORE_INTERRUPT, therefore phy_interrupt_is_valid() returns false.
As a result phy_change() effectively just calls phy_trigger_machine()
when called from phy_mac_interrupt() via phy_change_work(). So we can
call phy_trigger_machine() from phy_mac_interrupt() directly and
remove some now unneeded code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State PHY_CHANGELINK isn't needed here, we can call the state machine
directly. We just have to remove the check for phy_polling_mode() to
make this work also in interrupt mode. Removing this check doesn't
cause any overhead because when not polling the state machine is
called only if required by some event.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a heritage from the very early days of phylib member interrupts is
defined as u32 even though it's just a flag whether interrupts are
enabled. So we can change it to a bitfield member. In addition change
the code dealing with this member in a way that it's clear we're
dealing with a bool value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_check_link_status in more places in the state machine.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the recent changes in the state machine state PHY_AN isn't used
any longer and can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In few places in the state machine the state is set to PHY_RUNNING or
PHY_NOLINK after doing a phy_read_status(). So factor this out to
phy_check_link_status().
First use it in phy_start_aneg(): By setting the state to PHY_RUNNING
or PHY_NOLINK directly we can remove the code to handle the case that
we're using interrupts and aneg was finished already.
Definition of phy_link_up and phy_link_down needs to be moved because
they are called in the new function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If aneg isn't finished yet then the PHY reports the link as down.
There's no benefit in setting the state to PHY_AN because the next
state machine run would set the status to PHY_NOLINK anyway (except
in the meantime aneg has been finished and link is up). Therefore
we can set the state to PHY_RUNNING or PHY_NOLINK directly.
In addition change the do_carrier parameter in phy_link_down() to true.
If carrier was marked as up before (what should never be the case because
PHY was in state PHY_HALTED before) then we should mark it as down now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If aneg is enabled and the PHY reports the link as up then definitely
aneg finished successfully. Therefore this check is useless and
can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_trigger_machine() is used in phy.c only, so we can make it static.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
