When doing port mirroring, the physical port to send the frame to, is
written to the FRMC_PORT_VAL field of the QFWD_FRAME_COPY_CFG register.
This field is 7 bits wide on sparx5 and 6 bits wide on lan969x, and has
a default value of 65 and 30, respectively (the number of front ports).
On mirror deletion, we set the default value of the monitor port to
65 for this field, in case no more ports exists for the mirror. Needless
to say, this will not fit the 6 bits on lan969x.
Fix this by correctly using the n_ports constant instead.
Fixes: 3f9e46347a ("net: sparx5: use SPX5_CONST for constants which already have a symbol")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the is_sparx5() macro (introduced in earlier series [1]), in places
where we need to handle things a bit differently on lan969x.
These places are:
- in sparx5_dsm_calendar_update() we need to switch the calendar
from a to b on lan969x.
- in sparx5_start() we need to make sure the HSCH_SYS_CLK_PER
register is only touched on Sparx5.
- in sparx5_start() we need to disable VCAP and FDMA for lan969x
(will come in later series).
- in sparx5_mirror_port_get() we must make sure the
ANA_AC_PROBE_PORT_CFG1 register is only read on Sparx5.
- sparx5_netdev.c and sparx5_packet.c we need to use different IFH
(Internal Frame Header) offsets for lan969x.
- in sparx5_port_fifo_sz() we must bail out on lan969x.
- in sparx5_port_config_low_set() we must configure the phase
detection registers.
- in sparx5_port_config() and sparx5_port_init() we must do some
additional configuration of the port devices.
- in sparx5_dwrr_conf_set() we must derive the scheduling layer
[1] https://lore.kernel.org/netdev/20241004-b4-sparx5-lan969x-switch-driver-v2-8-d3290f581663@microchip.com/
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241024-sparx5-lan969x-switch-driver-2-v2-12-a0b5fae88a0f@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When port mirroring is added to a port, the bit position of the source
port, needs to be written to the register ANA_AC_PROBE_PORT_CFG. This
register is replicated for n_ports > 32, and therefore we need to derive
the correct register from the port number.
Before this patch, we wrongly calculate the register from portno /
BITS_PER_BYTE, where the divisor ought to be 32, causing any port >=8 to
be written to the wrong register. We fix this, by using do_div(), where
the dividend is the register, the remainder is the bit position and the
divisor is now 32.
Fixes: 4e50d72b3b ("net: sparx5: add port mirroring implementation")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241009-mirroring-fix-v1-1-9ec962301989@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for tc matchall mirror stats. When a new matchall mirror
rule is added, the baseline stats for that port is saved.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware supports three independent mirroring probes. Each probe can
be configured to mirror rx or tx traffic (direction).
Using tc matchall, it is now possible to add a source port and a monitor
port to a mirror probe. Depending on the mirror direction, rx or tx
traffic from a source port will be mirrored to the monitor port.
A single source port can be a member of multiple mirror probes.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
