2
0
mirror of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git synced 2025-09-04 20:19:47 +08:00
Commit Graph

866 Commits

Author SHA1 Message Date
Kai-Heng Feng
4e0effd900 igb: Make DMA faster when CPU is active on the PCIe link
Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps
Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which
will be significantly lower when 1) ASPM is disabled or 2) SoC package
c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx
speed can reach to ~950Mbps.

According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC",
"DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so
set it to 1b for "DMA is considered idle when there is no Rx or Tx AND
when there are no TLPs indicating that CPU is active detected on the
PCIe link (such as the host executes CSR or Configuration register read
or write operation)" and performing Tx should also fall under "active
CPU on PCIe link" case.

In addition to that, commit b6e0c419f0 ("igb: Move DMA Coalescing init
code to separate function.") seems to wrongly changed from enabling
E1000_PCIEMISC_LX_DECISION to disabling it, also fix that.

Fixes: b6e0c419f0 ("igb: Move DMA Coalescing init code to separate function.")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220621221056.604304-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-22 18:46:24 -07:00
Lorenzo Bianconi
3f6a57ee85 igb: fix a use-after-free issue in igb_clean_tx_ring
Fix the following use-after-free bug in igb_clean_tx_ring routine when
the NIC is running in XDP mode. The issue can be triggered redirecting
traffic into the igb NIC and then closing the device while the traffic
is flowing.

[   73.322719] CPU: 1 PID: 487 Comm: xdp_redirect Not tainted 5.18.3-apu2 #9
[   73.330639] Hardware name: PC Engines APU2/APU2, BIOS 4.0.7 02/28/2017
[   73.337434] RIP: 0010:refcount_warn_saturate+0xa7/0xf0
[   73.362283] RSP: 0018:ffffc9000081f798 EFLAGS: 00010282
[   73.367761] RAX: 0000000000000000 RBX: ffffc90000420f80 RCX: 0000000000000000
[   73.375200] RDX: ffff88811ad22d00 RSI: ffff88811ad171e0 RDI: ffff88811ad171e0
[   73.382590] RBP: 0000000000000900 R08: ffffffff82298f28 R09: 0000000000000058
[   73.390008] R10: 0000000000000219 R11: ffffffff82280f40 R12: 0000000000000090
[   73.397356] R13: ffff888102343a40 R14: ffff88810359e0e4 R15: 0000000000000000
[   73.404806] FS:  00007ff38d31d740(0000) GS:ffff88811ad00000(0000) knlGS:0000000000000000
[   73.413129] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   73.419096] CR2: 000055cff35f13f8 CR3: 0000000106391000 CR4: 00000000000406e0
[   73.426565] Call Trace:
[   73.429087]  <TASK>
[   73.431314]  igb_clean_tx_ring+0x43/0x140 [igb]
[   73.436002]  igb_down+0x1d7/0x220 [igb]
[   73.439974]  __igb_close+0x3c/0x120 [igb]
[   73.444118]  igb_xdp+0x10c/0x150 [igb]
[   73.447983]  ? igb_pci_sriov_configure+0x70/0x70 [igb]
[   73.453362]  dev_xdp_install+0xda/0x110
[   73.457371]  dev_xdp_attach+0x1da/0x550
[   73.461369]  do_setlink+0xfd0/0x10f0
[   73.465166]  ? __nla_validate_parse+0x89/0xc70
[   73.469714]  rtnl_setlink+0x11a/0x1e0
[   73.473547]  rtnetlink_rcv_msg+0x145/0x3d0
[   73.477709]  ? rtnl_calcit.isra.0+0x130/0x130
[   73.482258]  netlink_rcv_skb+0x8d/0x110
[   73.486229]  netlink_unicast+0x230/0x340
[   73.490317]  netlink_sendmsg+0x215/0x470
[   73.494395]  __sys_sendto+0x179/0x190
[   73.498268]  ? move_addr_to_user+0x37/0x70
[   73.502547]  ? __sys_getsockname+0x84/0xe0
[   73.506853]  ? netlink_setsockopt+0x1c1/0x4a0
[   73.511349]  ? __sys_setsockopt+0xc8/0x1d0
[   73.515636]  __x64_sys_sendto+0x20/0x30
[   73.519603]  do_syscall_64+0x3b/0x80
[   73.523399]  entry_SYSCALL_64_after_hwframe+0x44/0xae
[   73.528712] RIP: 0033:0x7ff38d41f20c
[   73.551866] RSP: 002b:00007fff3b945a68 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
[   73.559640] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007ff38d41f20c
[   73.567066] RDX: 0000000000000034 RSI: 00007fff3b945b30 RDI: 0000000000000003
[   73.574457] RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000000
[   73.581852] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fff3b945ab0
[   73.589179] R13: 0000000000000000 R14: 0000000000000003 R15: 00007fff3b945b30
[   73.596545]  </TASK>
[   73.598842] ---[ end trace 0000000000000000 ]---

Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/e5c01d549dc37bff18e46aeabd6fb28a7bcf84be.1655388571.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-17 20:14:07 -07:00
Kai-Heng Feng
a413f2803d igb: Remove duplicate defines
There's no need to define same thing twice.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-06-09 10:05:31 -07:00
Jakub Kicinski
d7e6f58360 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
drivers/net/ethernet/mellanox/mlx5/core/main.c
  b33886971d ("net/mlx5: Initialize flow steering during driver probe")
  40379a0084 ("net/mlx5_fpga: Drop INNOVA TLS support")
  f2b41b32cd ("net/mlx5: Remove ipsec_ops function table")
https://lore.kernel.org/all/20220519040345.6yrjromcdistu7vh@sx1/
  16d42d3133 ("net/mlx5: Drain fw_reset when removing device")
  8324a02c34 ("net/mlx5: Add exit route when waiting for FW")
https://lore.kernel.org/all/20220519114119.060ce014@canb.auug.org.au/

tools/testing/selftests/net/mptcp/mptcp_join.sh
  e274f71540 ("selftests: mptcp: add subflow limits test-cases")
  b6e074e171 ("selftests: mptcp: add infinite map testcase")
  5ac1d2d634 ("selftests: mptcp: Add tests for userspace PM type")
https://lore.kernel.org/all/20220516111918.366d747f@canb.auug.org.au/

net/mptcp/options.c
  ba2c89e0ea ("mptcp: fix checksum byte order")
  1e39e5a32a ("mptcp: infinite mapping sending")
  ea66758c17 ("tcp: allow MPTCP to update the announced window")
https://lore.kernel.org/all/20220519115146.751c3a37@canb.auug.org.au/

net/mptcp/pm.c
  95d6865178 ("mptcp: fix subflow accounting on close")
  4d25247d3a ("mptcp: bypass in-kernel PM restrictions for non-kernel PMs")
https://lore.kernel.org/all/20220516111435.72f35dca@canb.auug.org.au/

net/mptcp/subflow.c
  ae66fb2ba6 ("mptcp: Do TCP fallback on early DSS checksum failure")
  0348c690ed ("mptcp: add the fallback check")
  f8d4bcacff ("mptcp: infinite mapping receiving")
https://lore.kernel.org/all/20220519115837.380bb8d4@canb.auug.org.au/

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-19 11:23:59 -07:00
Kevin Mitchell
942d2ad5d2 igb: skip phy status check where unavailable
igb_read_phy_reg() will silently return, leaving phy_data untouched, if
hw->ops.read_reg isn't set. Depending on the uninitialized value of
phy_data, this led to the phy status check either succeeding immediately
or looping continuously for 2 seconds before emitting a noisy err-level
timeout. This message went out to the console even though there was no
actual problem.

Instead, first check if there is read_reg function pointer. If not,
proceed without trying to check the phy status register.

Fixes: b72f3f7200 ("igb: When GbE link up, wait for Remote receiver status condition")
Signed-off-by: Kevin Mitchell <kevmitch@arista.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-18 14:00:51 +01:00
Alaa Mohamed
b35413f415 igb: Convert kmap() to kmap_local_page()
kmap() is being deprecated and these usages are all local to the thread
so there is no reason kmap_local_page() can't be used.

Replace kmap() calls with kmap_local_page().

Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-05-05 08:37:14 -07:00
Tom Rix
5d705de0cd igb: zero hwtstamp by default
Clang static analysis reports this representative issue
igb_ptp.c:997:3: warning: The left operand of '+' is a
  garbage value
  ktime_add_ns(shhwtstamps.hwtstamp, adjust);
  ^            ~~~~~~~~~~~~~~~~~~~~

shhwtstamps.hwtstamp is set by a call to
igb_ptp_systim_to_hwtstamp().  In the switch-statement
for the hw type, the hwtstamp is zeroed for matches
but not the default case.  Move the memset out of
switch-statement.  This degarbages the default case
and reduces the size.

Some whitespace cleanup of empty lines

Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-03-17 08:32:28 -07:00
Corinna Vinschen
e62ad74aa5 igb: refactor XDP registration
On changing the RX ring parameters igb uses a hack to avoid a warning
when calling xdp_rxq_info_reg via igb_setup_rx_resources.  It just
clears the struct xdp_rxq_info content.

Instead, change this to unregister if we're already registered.  Align
code to the igc code.

Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-02-07 14:23:01 -08:00
Christophe JAILLET
f80f4dc3b2 igb: Remove useless DMA-32 fallback configuration
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.

So, if dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be
1.

Simplify code and remove some dead code accordingly.

[1]: https://lkml.org/lkml/2021/6/7/398

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-01-27 08:58:24 -08:00
David S. Miller
e63a023489 Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Alexei Starovoitov says:

====================
pull-request: bpf-next 2021-12-30

The following pull-request contains BPF updates for your *net-next* tree.

We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).

The main changes are:

1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.

2) Beautify and de-verbose verifier logs, from Christy.

3) Composable verifier types, from Hao.

4) bpf_strncmp helper, from Hou.

5) bpf.h header dependency cleanup, from Jakub.

6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.

7) Sleepable local storage, from KP.

8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-31 14:35:40 +00:00
Ruud Bos
38970eac41 igb: support EXTTS on 82580/i354/i350
Support for the PTP pin function on 82580/i354/i350 based adapters.
Because the time registers of these adapters do not have the nice split in
second rollovers as the i210 has, the implementation is slightly more
complex compared to the i210 implementation.

Signed-off-by: Ruud Bos <kernel.hbk@gmail.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-12-29 10:01:04 -08:00
Ruud Bos
1819fc753a igb: support PEROUT on 82580/i354/i350
Support for the PEROUT PTP pin function on 82580/i354/i350 based adapters.
Because the time registers of these adapters do not have the nice split in
second rollovers as the i210 has, the implementation is slightly more
complex compared to the i210 implementation.

Signed-off-by: Ruud Bos <kernel.hbk@gmail.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-12-29 10:01:04 -08:00
Ruud Bos
cf99c1dd7b igb: move PEROUT and EXTTS isr logic to separate functions
Remove code duplication in the tsync interrupt handler function by moving
this logic to separate functions. This keeps the interrupt handler readable
and allows the new functions to be extended for adapter types other than
i210.

Signed-off-by: Ruud Bos <kernel.hbk@gmail.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-12-29 10:01:03 -08:00
Ruud Bos
8ab55aba31 igb: move SDP config initialization to separate function
Allow reuse of SDP config struct initialization by moving it to a
separate function.

Signed-off-by: Ruud Bos <kernel.hbk@gmail.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-12-29 10:01:03 -08:00
Alexander Lobakin
fa441f0fa8 igb: switch to napi_build_skb()
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
igb driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.

Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-12-28 09:42:33 -08:00
Jakub Kicinski
8b3f913322 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
include/net/sock.h
  commit 8f905c0e73 ("inet: fully convert sk->sk_rx_dst to RCU rules")
  commit 43f51df417 ("net: move early demux fields close to sk_refcnt")
  https://lore.kernel.org/all/20211222141641.0caa0ab3@canb.auug.org.au/

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-23 16:09:58 -08:00
Jason Wang
890781af31 igb: remove never changed variable `ret_val'
The variable used for return status in `igb_write_xmdio_reg' function
is never changed  and this function is just need return 0. Thus, the
`ret_val' can be removed and return 0 at the end of the
`igb_write_xmdio_reg' function.

Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-12-21 09:17:47 -08:00
Heiner Kallweit
ac8c58f5b5 igb: fix deadlock caused by taking RTNL in RPM resume path
Recent net core changes caused an issue with few Intel drivers
(reportedly igb), where taking RTNL in RPM resume path results in a
deadlock. See [0] for a bug report. I don't think the core changes
are wrong, but taking RTNL in RPM resume path isn't needed.
The Intel drivers are the only ones doing this. See [1] for a
discussion on the issue. Following patch changes the RPM resume path
to not take RTNL.

[0] https://bugzilla.kernel.org/show_bug.cgi?id=215129
[1] https://lore.kernel.org/netdev/20211125074949.5f897431@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com/t/

Fixes: bd869245a3 ("net: core: try to runtime-resume detached device in __dev_open")
Fixes: f32a213765 ("ethtool: runtime-resume netdev parent before ethtool ioctl ops")
Tested-by: Martin Stolpe <martin.stolpe@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20211220201844.2714498-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-20 18:48:09 -08:00
Jakub Kicinski
7cd2802d74 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
No conflicts.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-16 16:13:19 -08:00
Karen Sornek
584af82154 igb: Fix removal of unicast MAC filters of VFs
Move checking condition of VF MAC filter before clearing
or adding MAC filter to VF to prevent potential blackout caused
by removal of necessary and working VF's MAC filter.

Fixes: 1b8b062a99 ("igb: add VF trust infrastructure")
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-12-15 11:08:18 -08:00
Hangbin Liu
9c9211a3fc net_tstamp: add new flag HWTSTAMP_FLAG_BONDED_PHC_INDEX
Since commit 94dd016ae5 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.

This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.

With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.

Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-14 12:28:24 +00:00
Paolo Abeni
c8064e5b4a bpf: Let bpf_warn_invalid_xdp_action() report more info
In non trivial scenarios, the action id alone is not sufficient to
identify the program causing the warning. Before the previous patch,
the generated stack-trace pointed out at least the involved device
driver.

Let's additionally include the program name and id, and the relevant
device name.

If the user needs additional infos, he can fetch them via a kernel
probe, leveraging the arguments added here.

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/ddb96bb975cbfddb1546cf5da60e77d5100b533c.1638189075.git.pabeni@redhat.com
2021-12-13 22:28:27 +01:00
Jakub Kicinski
93d5404e89 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
drivers/net/ipa/ipa_main.c
  8afc7e471a ("net: ipa: separate disabling setup from modem stop")
  76b5fbcd6b ("net: ipa: kill ipa_modem_init()")

Duplicated include, drop one.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26 13:45:19 -08:00
Jesse Brandeburg
eaeace6077 igb: fix netpoll exit with traffic
Oleksandr brought a bug report where netpoll causes trace
messages in the log on igb.

Danielle brought this back up as still occurring, so we'll try
again.

[22038.710800] ------------[ cut here ]------------
[22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll
[22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0

As Alex suggested, change the driver to return work_done at the
exit of napi_poll, which should be safe to do in this driver
because it is not polling multiple queues in this single napi
context (multiple queues attached to one MSI-X vector). Several
other drivers contain the same simple sequence, so I hope
this will not create new problems.

Fixes: 16eb8815c2 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Danielle Ratson <danieller@nvidia.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-25 07:39:31 -08:00
Hao Chen
7462494408 ethtool: extend ringparam setting/getting API with rx_buf_len
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.

Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-22 12:31:49 +00:00
Eric Dumazet
5337824f4d net: annotate accesses to queue->trans_start
In following patches, dev_watchdog() will no longer stop all queues.
It will read queue->trans_start locklessly.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-17 14:56:16 +00:00
Jan Kundrát
a97f8783a9 igb: unbreak I2C bit-banging on i350
The driver tried to use Linux' native software I2C bus master
(i2c-algo-bits) for exporting the I2C interface that talks to the SFP
cage(s) towards userspace. As-is, however, the physical SCL/SDA pins
were not moving at all, staying at logical 1 all the time.

The main culprit was the I2CPARAMS register where igb was not setting
the I2CBB_EN bit. That meant that all the careful signal bit-banging was
actually not being propagated to the chip pads (I verified this with a
scope).

The bit-banging was not correct either, because I2C is supposed to be an
open-collector bus, and the code was driving both lines via a totem
pole. The code was also trying to do operations which did not make any
sense with the i2c-algo-bits, namely manipulating both SDA and SCL from
igb_set_i2c_data (which is only supposed to set SDA). I'm not sure if
that was meant as an optimization, or was just flat out wrong, but given
that the i2c-algo-bits is set up to work with a totally dumb GPIO-ish
implementation underneath, there's no need for this code to be smart.

The open-drain vs. totem-pole is fixed by the usual trick where the
logical zero is implemented via regular output mode and outputting a
logical 0, and the logical high is implemented via the IO pad configured
as an input (thus floating), and letting the mandatory pull-up resistors
do the rest. Anything else is actually wrong on I2C where all devices
are supposed to have open-drain connection to the bus.

The missing I2CBB_EN is set (along with a safe initial value of the
GPIOs) just before registering this software I2C bus.

The chip datasheet mentions HW-implemented I2C transactions (SFP EEPROM
reads and writes) as well, but I'm not touching these for simplicity.

Tested on a LR-Link LRES2203PF-2SFP (which is an almost-miniPCIe form
factor card, a cable, and a module with two SFP cages). There was one
casualty, an old broken SFP we had laying around, which was used to
solder some thin wires as a DIY I2C breakout. Thanks for your service.
With this patch in place, I can `i2cdump -y 3 0x51 c` and read back data
which make sense. Yay.

Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
See-also: https://www.spinics.net/lists/netdev/msg490554.html
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-29 09:42:59 -07:00
Jakub Kicinski
a05e4c0af4 ethernet: use eth_hw_addr_set() for dev->addr_len cases
Convert all Ethernet drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():

  @@
  expression dev, np;
  @@
  - memcpy(dev->dev_addr, np, dev->addr_len)
  + eth_hw_addr_set(dev, np)

In theory addr_len may not be ETH_ALEN, but we don't expect
non-Ethernet devices to live under this directory, and only
the following cases of setting addr_len exist:
 - cxgb4 for mgmt device,
and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-05 13:16:48 +01:00
Yufeng Mo
f3ccfda193 ethtool: extend coalesce setting uAPI with CQE mode
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-24 07:38:29 -07:00
Arnd Bergmann
a76053707d dev_ioctl: split out ndo_eth_ioctl
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.

Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.

This is a purely cosmetic change intended to help readers find
their way through the implementation.

Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27 20:11:45 +01:00
Kees Cook
c9183f45e4 igb: Avoid memcpy() over-reading of ETH_SS_STATS
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.

The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.

Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-07-23 09:08:11 -07:00
Grzegorz Siwik
07be39e32d igb: Add counter to i21x doublecheck
Add failed_counter to i21x_doublecheck(). There is possibility that
loop will never end.
With this patch the loop will stop after maximum 3 retries
to write to MTA_REGISTER

Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-07-23 09:08:11 -07:00
Jedrzej Jagielski
382a7c20d9 igb: Fix position of assignment to *ring
Assignment to *ring should be done after correctness check of the
argument queue.

Fixes: 91db364236 ("igb: Refactor igb_configure_cbs()")
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-07-01 10:59:21 -07:00
Aleksandr Loktionov
6c19d77261 igb: Check if num of q_vectors is smaller than max before array access
Ensure that the adapter->q_vector[MAX_Q_VECTORS] array isn't accessed
beyond its size. It was fixed by using a local variable num_q_vectors
as a limit for loop index, and ensure that num_q_vectors is not bigger
than MAX_Q_VECTORS.

Fixes: 047e0030f1 ("igb: add new data structure for handling interrupts and NAPI")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Slawomir Laba <slawomirx.laba@intel.com>
Reviewed-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Reviewed-by: Mateusz Palczewski <mateusz.placzewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-07-01 10:59:21 -07:00
Christophe JAILLET
fea03b1ceb igb: Fix an error handling path in 'igb_probe()'
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.

Fixes: 40a914fa72 ("igb: Add support for pci-e Advanced Error Reporting")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-07-01 10:59:04 -07:00
Vinicius Costa Gomes
7b292608db igb: Fix use-after-free error during reset
Cleans the next descriptor to watch (next_to_watch) when cleaning the
TX ring.

Failure to do so can cause invalid memory accesses. If igb_poll() runs
while the controller is reset this can lead to the driver try to free
a skb that was already freed.

(The crash is harder to reproduce with the igb driver, but the same
potential problem exists as the code is identical to igc)

Fixes: 7cc6fd4c60 ("igb: Don't bother clearing Tx buffer_info in igb_clean_tx_ring")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reported-by: Erez Geva <erez.geva.ext@siemens.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-07-01 10:53:04 -07:00
Toke Høiland-Jørgensen
49589b23d5 intel: Remove rcu_read_lock() around XDP program invocation
The Intel drivers all have rcu_read_lock()/rcu_read_unlock() pairs around
XDP program invocations. However, the actual lifetime of the objects
referred by the XDP program invocation is longer, all the way through to
the call to xdp_do_flush(), making the scope of the rcu_read_lock() too
small. This turns out to be harmless because it all happens in a single
NAPI poll cycle (and thus under local_bh_disable()), but it makes the
rcu_read_lock() misleading.

Rather than extend the scope of the rcu_read_lock(), just get rid of it
entirely. With the addition of RCU annotations to the XDP_REDIRECT map
types that take bh execution into account, lockdep even understands this to
be safe, so there's really no reason to keep it around.

Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com> # i40e
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Link: https://lore.kernel.org/bpf/20210624160609.292325-12-toke@redhat.com
2021-06-24 19:44:34 +02:00
David S. Miller
126285651b Merge ra.kernel.org:/pub/scm/linux/kernel/git/netdev/net
Bug fixes overlapping feature additions and refactoring, mostly.

Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-07 13:01:52 -07:00
Magnus Karlsson
74431c40b9 igb: add correct exception tracing for XDP
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.

Fixes: 9cbc948b5a ("igb: add XDP support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-06-03 08:38:37 -07:00
Kurt Kanzenbach
5379260852 igb: Fix XDP with PTP enabled
When using native XDP with the igb driver, the XDP frame data doesn't point to
the beginning of the packet. It's off by 16 bytes. Everything works as expected
with XDP skb mode.

Actually these 16 bytes are used to store the packet timestamps. Therefore, pull
the timestamp before executing any XDP operations and adjust all other code
accordingly. The igc driver does it like that as well.

Tested with Intel i210 card and AF_XDP sockets.

Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-06-03 08:38:37 -07:00
YueHaibing
0a206f9d9e igb: Fix -Wunused-const-variable warning
If CONFIG_IGB_HWMON is n, gcc warns:

drivers/net/ethernet/intel/igb/e1000_82575.c:2765:17:
 warning: ‘e1000_emc_therm_limit’ defined but not used [-Wunused-const-variable=]
 static const u8 e1000_emc_therm_limit[4] = {
                 ^~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/igb/e1000_82575.c:2759:17:
 warning: ‘e1000_emc_temp_data’ defined but not used [-Wunused-const-variable=]
 static const u8 e1000_emc_temp_data[4] = {
                 ^~~~~~~~~~~~~~~~~~~

Move it into #ifdef block to fix this.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-01 17:00:51 -07:00
Jesse Brandeburg
9fb8602e56 igb: override two checker warnings
The igb PTP code was using htons() on a constant to try to
byte swap the value before writing it to a register. This byte
swap has the consequence of triggering sparse conflicts between
the register write which expect cpu ordered input, and the code
which generated a big endian constant. Just override the cast
to make sure code doesn't change but silence the warning.

Can't do a __swab16 in this case because big endian systems
would then write the wrong value.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-05-26 09:11:41 -07:00
Jesse Brandeburg
b514958dd1 igb: fix assignment on big endian machines
The igb driver was trying hard to be sparse correct, but somehow
ended up converting a variable into little endian order and then
tries to OR something with it.

A much plainer way of doing things is to leave all variables and
OR operations in CPU (non-endian) mode, and then convert to
little endian only once, which is what this change does.

This probably fixes a bug that might have been seen only on
big endian systems.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-05-26 09:11:41 -07:00
Jesse Brandeburg
c7cbfb028b igb: handle vlan types with checker enabled
The sparse build (C=2) finds some issues with how the driver
dealt with the (very difficult) hardware that in some generations
uses little-endian, and in others uses big endian, for the VLAN
field. The code as written picks __le16 as a type and for some
hardware revisions we override it to __be16 as done in this
patch. This impacted the VF driver as well so fix it there too.

Also change the vlan_tci assignment to override the sparse
warning without changing functionality.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-05-26 09:11:41 -07:00
Jesse Brandeburg
88c228b22e igb/igc: use strongly typed pointer
The igb and igc driver both use a trick of creating a local type
pointer on the stack to ease dealing with a receive descriptor in
64 bit chunks for printing.  Sparse however was not taken into
account and receive descriptors are always in little endian
order, so just make the unions use __le64 instead of u64.

No functional change.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-05-26 09:11:41 -07:00
Jesse Brandeburg
c40591cc3d intel: remove checker warning
The sparse checker (C=2) found an assignment where we were mixing
types when trying to convert from data read directly from the
device NVM, to an array in CPU order in-memory, which
unfortunately the driver tries to do in-place.

This is easily solved by using the swap operation instead of an
assignment, and is already proven in other Intel drivers to be
functionally correct and the same code, just without a sparse
warning.

The change is the same in all three drivers.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-05-26 09:11:40 -07:00
Grzegorz Siwik
1d3cb90cb0 igb: Add double-check MTA_REGISTER for i210 and i211
Add new function which checks MTA_REGISTER if its filled correctly.
If not then writes again to same register.
There is possibility that i210 and i211 could not accept
MTA_REGISTER settings, specially when you add and remove
many of multicast addresses in short time.
Without this patch there is possibility that multicast settings will be
not always set correctly in hardware.

Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-04-16 13:15:39 -07:00
Ederson de Souza
26b67f5a1e igb: Redistribute memory for transmit packet buffers when in Qav mode
i210 has a total of 24KB of transmit packet buffer. When in Qav mode,
this buffer is divided into four pieces, one for each Tx queue.
Currently, 8KB are given to each of the two SR queues and 4KB are given
to each of the two SP queues.

However, it was noticed that such distribution can make best effort
traffic (which would usually go to the SP queues when Qav is enabled, as
the SR queues would be used by ETF or CBS qdiscs for TSN-aware traffic)
perform poorly. Using iperf3 to measure, one could see the performance
of best effort traffic drop by nearly a third (from 935Mbps to 578Mbps),
with no TSN traffic competing.

This patch redistributes the 24KB to each queue equally: 6KB each. On
tests, there was no notable performance reduction of best effort traffic
performance when there was no TSN traffic competing.

Below, more details about the data collected:

All experiments were run using the following qdisc setup:

qdisc taprio 100: root refcnt 9 tc 4 map 3 3 3 2 3 0 0 3 3 3 3 3 3 3 3 3
    queues offset 0 count 1 offset 1 count 1 offset 2 count 1 offset 3 count 1
    clockid TAI base-time 0 cycle-time 10000000 cycle-time-extension 0
    index 0 cmd S gatemask 0xf interval 10000000

qdisc etf 8045: parent 100:1 clockid TAI delta 1000000 offload on
    deadline_mode off skip_sock_check off

TSN traffic, when enabled, had this characteristics:
 Packet size: 1500 bytes
 Transmission interval: 125us

----------------------------------
Without this patch:
----------------------------------
- TCP data:
    - No TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Retr
        [  5]   0.00-20.00  sec  1.35 GBytes   578 Mbits/sec    0

    - With TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Retr
        [  5]   0.00-20.00  sec  1.07 GBytes   460 Mbits/sec    1

- TCP data limiting iperf3 buffer size to 4K:
    - No TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Retr
        [  5]   0.00-20.00  sec  1.35 GBytes   579 Mbits/sec    0

    - With TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Retr
        [  5]   0.00-20.00  sec  1.08 GBytes   462 Mbits/sec    0

- TCP data limiting iperf3 buffer size to 192 bytes (smallest size without
 serious performance degradation):
    - No TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Retr
        [  5]   0.00-20.00  sec  1.34 GBytes   577 Mbits/sec    0

    - With TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Retr
        [  5]   0.00-20.00  sec  1.07 GBytes   461 Mbits/sec    1

- UDP data at 1000Mbit/sec:
    - No TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Jitter    Lost/Total Datagrams
        [  5]   0.00-20.00  sec  1.36 GBytes   586 Mbits/sec  0.000 ms  0/1011407 (0%)

    - With TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Jitter    Lost/Total Datagrams
        [  5]   0.00-20.00  sec  1.05 GBytes   451 Mbits/sec  0.000 ms  0/778672 (0%)

----------------------------------
With this patch:
----------------------------------

- TCP data:
    - No TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Retr
        [  5]   0.00-20.00  sec  2.17 GBytes   932 Mbits/sec    0

    - With TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Retr
        [  5]   0.00-20.00  sec  1.50 GBytes   646 Mbits/sec    1

- TCP data limiting iperf3 buffer size to 4K:
    - No TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Retr
        [  5]   0.00-20.00  sec  2.17 GBytes   931 Mbits/sec    0

    - With TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Retr
        [  5]   0.00-20.00  sec  1.50 GBytes   645 Mbits/sec    0

- TCP data limiting iperf3 buffer size to 192 bytes (smallest size without
 serious performance degradation):
    - No TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Retr
        [  5]   0.00-20.00  sec  2.17 GBytes   932 Mbits/sec    1

    - With TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Retr
        [  5]   0.00-20.00  sec  1.50 GBytes   645 Mbits/sec    0

- UDP data at 1000Mbit/sec:
    - No TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Jitter    Lost/Total Datagrams
        [  5]   0.00-20.00  sec  2.23 GBytes   956 Mbits/sec  0.000 ms  0/1650226 (0%)

    - With TSN traffic:
        [ ID] Interval           Transfer     Bitrate         Jitter    Lost/Total Datagrams
        [  5]   0.00-20.00  sec  1.51 GBytes   649 Mbits/sec  0.000 ms  0/1120264 (0%)

Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-04-16 10:42:52 -07:00
David S. Miller
241949e488 Merge https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Alexei Starovoitov says:

====================
pull-request: bpf-next 2021-03-24

The following pull-request contains BPF updates for your *net-next* tree.

We've added 37 non-merge commits during the last 15 day(s) which contain
a total of 65 files changed, 3200 insertions(+), 738 deletions(-).

The main changes are:

1) Static linking of multiple BPF ELF files, from Andrii.

2) Move drop error path to devmap for XDP_REDIRECT, from Lorenzo.

3) Spelling fixes from various folks.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-25 16:30:46 -07:00
David S. Miller
efd13b71a3 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-25 15:31:22 -07:00
Gustavo A. R. Silva
52c406989a igb: Fix fall-through warnings for Clang
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of just
letting the code fall through to the next case.

Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-03-23 11:34:02 -07:00
Jesse Brandeburg
262de08f64 intel: clean up mismatched header comments
A bunch of header comments were showing warnings when compiling
with W=1. Fix them all at once. This changes only comments.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-03-23 11:34:02 -07:00
Jesse Brandeburg
f0a03a0268 igb: check timestamp validity
Add a couple of checks to make sure timestamping is on and that the
timestamp value from DMA is valid. This avoids any functional issues
that could come from a misinterpreted time stamp.

One of the functions changed doesn't need a return value added because
there was no value in checking from the calling locations.

While here, fix a couple of reverse christmas tree issues next to
the code being changed.

Fixes: f56e7bba22 ("igb: Pull timestamp from fragment before adding it to skb")
Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-03-19 08:47:46 -07:00
Tom Seewald
a75519a848 igb: Fix duplicate include guard
The include guard "_E1000_HW_H_" is used by two separate header files in
two different drivers (e1000/e1000_hw.h and igb/e1000_hw.h). Using the
same include guard macro in more than one header file may cause
unexpected behavior from the compiler. Fix this by renaming the
duplicate guard in the igb driver.

Fixes: 9d5c824399 ("igb: PCI-Express 82575 Gigabit Ethernet driver")
Signed-off-by: Tom Seewald <tseewald@gmail.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-03-19 08:47:46 -07:00
Lorenzo Bianconi
fdc13979f9 bpf, devmap: Move drop error path to devmap for XDP_REDIRECT
We want to change the current ndo_xdp_xmit drop semantics because it will
allow us to implement better queue overflow handling. This is working
towards the larger goal of a XDP TX queue-hook. Move XDP_REDIRECT error
path handling from each XDP ethernet driver to devmap code. According to
the new APIs, the driver running the ndo_xdp_xmit pointer, will break tx
loop whenever the hw reports a tx error and it will just return to devmap
caller the number of successfully transmitted frames. It will be devmap
responsibility to free dropped frames.

Move each XDP ndo_xdp_xmit capable driver to the new APIs:

- veth
- virtio-net
- mvneta
- mvpp2
- socionext
- amazon ena
- bnxt
- freescale (dpaa2, dpaa)
- xen-frontend
- qede
- ice
- igb
- ixgbe
- i40e
- mlx5
- ti (cpsw, cpsw-new)
- tun
- sfc

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/bpf/ed670de24f951cfd77590decf0229a0ad7fd12f6.1615201152.git.lorenzo@kernel.org
2021-03-18 16:38:51 +01:00
Alexander Duyck
c8d4725e98 intel: Update drivers to use ethtool_sprintf
Update the Intel drivers to make use of ethtool_sprintf. The general idea
is to reduce code size and overhead by replacing the repeated pattern of
string printf statements and ETH_STRING_LEN counter increments.

Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-17 11:42:30 -07:00
Bhaskar Chowdhury
6f05a12241 net: ethernet: intel: igb: Typo fix in the file igb_main.c
s/structue/structure/

Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-15 12:48:20 -07:00
Li RongQing
98dfb02aa2 igb: avoid premature Rx buffer reuse
Igb needs a similar fix as commit 75aab4e10a ("i40e: avoid
premature Rx buffer reuse")

The page recycle code, incorrectly, relied on that a page fragment
could not be freed inside xdp_do_redirect(). This assumption leads to
that page fragments that are used by the stack/XDP redirect can be
reused and overwritten.

To avoid this, store the page count prior invoking xdp_do_redirect().

Longer explanation:

Intel NICs have a recycle mechanism. The main idea is that a page is
split into two parts. One part is owned by the driver, one part might
be owned by someone else, such as the stack.

t0: Page is allocated, and put on the Rx ring
              +---------------
used by NIC ->| upper buffer
(rx_buffer)   +---------------
              | lower buffer
              +---------------
  page count  == USHRT_MAX
  rx_buffer->pagecnt_bias == USHRT_MAX

t1: Buffer is received, and passed to the stack (e.g.)
              +---------------
              | upper buff (skb)
              +---------------
used by NIC ->| lower buffer
(rx_buffer)   +---------------
  page count  == USHRT_MAX
  rx_buffer->pagecnt_bias == USHRT_MAX - 1

t2: Buffer is received, and redirected
              +---------------
              | upper buff (skb)
              +---------------
used by NIC ->| lower buffer
(rx_buffer)   +---------------

Now, prior calling xdp_do_redirect():
  page count  == USHRT_MAX
  rx_buffer->pagecnt_bias == USHRT_MAX - 2

This means that buffer *cannot* be flipped/reused, because the skb is
still using it.

The problem arises when xdp_do_redirect() actually frees the
segment. Then we get:
  page count  == USHRT_MAX - 1
  rx_buffer->pagecnt_bias == USHRT_MAX - 2

From a recycle perspective, the buffer can be flipped and reused,
which means that the skb data area is passed to the Rx HW ring!

To work around this, the page count is stored prior calling
xdp_do_redirect().

Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-03-12 08:44:05 -08:00
Vladimir Oltean
847cbfc014 net: add a helper to avoid issues with HW TX timestamping and SO_TXTIME
As explained in commit 29d98f54a4 ("net: enetc: allow hardware
timestamping on TX queues with tc-etf enabled"), hardware TX
timestamping requires an skb with skb->tstamp = 0. When a packet is sent
with SO_TXTIME, the skb->skb_mstamp_ns corrupts the value of skb->tstamp,
so the drivers need to explicitly reset skb->tstamp to zero after
consuming the TX time.

Create a helper named skb_txtime_consumed() which does just that. All
drivers which offload TC_SETUP_QDISC_ETF should implement it, and it
would make it easier to assess during review whether they do the right
thing in order to be compatible with hardware timestamping or not.

Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-10 12:45:16 -08:00
Jakub Kicinski
4d469ec8ec Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:

====================
1GbE Intel Wired LAN Driver Updates 2021-02-03

This series contains updates to igc, igb, e1000e, and e1000 drivers.

Sasha adds counting of good transmit packets and reporting of NVM version
and gPHY version in ethtool firmware version. Replaces the use of strlcpy
to the preferred strscpy. Fixes a typo that caused the wrong register to be
output. He also removes an unused function pointer, some unneeded defines,
and a non-applicable comment. All changes for igc.

Gal Hammer fixes a typo which caused the RDBAL register values to be
shown instead of TDBAL for igb.

Nick Lowe enables RSS support for i211 devices for igb.

Tom Rix fixes checkpatch warning by removing h from printk format
specifier for igb.

Kaixu Xia removes setting of a variable that is overwritten before next
use for e1000e.

Sudip Mukherjee removes an unneeded assignment for e1000.

* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  e1000: drop unneeded assignment in e1000_set_itr()
  e1000e: remove the redundant value assignment in e1000_update_nvm_checksum_spt
  igb: remove h from printk format specifier
  igb: Enable RSS for Intel I211 Ethernet Controller
  igb: fix TDBAL register show incorrect value
  igc: Fix TDBAL register show incorrect value
  igc: Remove unused FUNC_1 mask
  igc: Remove unused local receiver mask
  igc: Prefer strscpy over strlcpy
  igc: Expose the gPHY firmware version
  igc: Expose the NVM version
  igc: Add Host Good Packets Transmitted Count
  igc: Remove MULR mask define
  igc: Remove igc_set_fw_version comment
  igc: Clean up nvm_operations structure
====================

Link: https://lore.kernel.org/r/20210204004259.3662059-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-02-04 21:26:28 -08:00
Alexander Lobakin
a79afa78e6 net: use the new dev_page_is_reusable() instead of private versions
Now we can remove a bunch of identical functions from the drivers and
make them use common dev_page_is_reusable(). All {,un}likely() checks
are omitted since it's already present in this helper.
Also update some comments near the call sites.

Suggested-by: David Rientjes <rientjes@google.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-02-04 18:20:14 -08:00
Tom Rix
2f7c1fd23d igb: remove h from printk format specifier
This change fixes the checkpatch warning described in this
commit cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")

Standard integer promotion is already done and %hx and %hhx is useless
so do not encourage the use of %hh[xudi] or %h[xudi].

Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-02-03 16:32:18 -08:00
Nick Lowe
6e6026f2dd igb: Enable RSS for Intel I211 Ethernet Controller
The Intel I211 Ethernet Controller supports 2 Receive Side Scaling (RSS)
queues. It should not be excluded from having this feature enabled.

Via commit c883de9fd7 ("igb: rename igb define to be more generic")
E1000_MRQC_ENABLE_RSS_4Q was renamed to E1000_MRQC_ENABLE_RSS_MQ to
indicate that this is a generic bit flag to enable queues and not
a flag that is specific to devices that support 4 queues

The bit flag enables 2, 4 or 8 queues appropriately depending on the part.

Tested with a multicore CPU and frames were then distributed as expected.

This issue appears to have been introduced because of confusion caused
by the prior name.

Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Tested-by: David Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-02-03 16:32:17 -08:00
Gal Hammer
abb9efc709 igb: fix TDBAL register show incorrect value
Fixed a typo which caused the registers dump function to read the
RDBAL register when printing TDBAL register values.

Signed-off-by: Gal Hammer <ghammer@redhat.com>
Tested-by: David Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-02-03 16:32:17 -08:00
Xin Long
8bcf02035b net: igb: use skb_csum_is_sctp instead of protocol check
Using skb_csum_is_sctp is a easier way to validate it's a SCTP
CRC checksum offload packet, and there is no need to parse the
packet to check its proto field, especially when it's a UDP or
GRE encapped packet.

So this patch also makes igb support SCTP CRC checksum offload
for UDP and GRE encapped packets.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-19 14:31:25 -08:00
Lorenzo Bianconi
be9df4aff6 net, xdp: Introduce xdp_prepare_buff utility routine
Introduce xdp_prepare_buff utility routine to initialize per-descriptor
xdp_buff fields (e.g. xdp_buff pointers). Rely on xdp_prepare_buff() in
all XDP capable drivers.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/bpf/45f46f12295972a97da8ca01990b3e71501e9d89.1608670965.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2021-01-08 13:39:24 -08:00
Lorenzo Bianconi
43b5169d83 net, xdp: Introduce xdp_init_buff utility routine
Introduce xdp_init_buff utility routine to initialize xdp_buff fields
const over NAPI iterations (e.g. frame_sz or rxq pointer). Rely on
xdp_init_buff in all XDP capable drivers.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/bpf/7f8329b6da1434dc2b05a77f2e800b29628a8913.1608670965.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2021-01-08 13:39:24 -08:00
Jakub Kicinski
46d5e62dd3 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().

strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.

Conflicts:
	net/netfilter/nf_tables_api.c

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-12-11 22:29:38 -08:00
Sven Auhagen
ec107e775d igb: avoid transmit queue timeout in xdp path
Since we share the transmit queue with the network stack,
it is possible that we run into a transmit queue timeout.
This will reset the queue.
This happens under high load when XDP is using the
transmit queue pretty much exclusively.

netdev_start_xmit() sets the trans_start variable of the
transmit queue to jiffies which is later utilized by dev_watchdog(),
so to avoid timeout, let stack know that XDP xmit happened by
bumping the trans_start within XDP Tx routines to jiffies.

Fixes: 9cbc948b5a ("igb: add XDP support")
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-12-09 15:26:58 -08:00
Sven Auhagen
3eca859008 igb: use xdp_do_flush
Since it is a new XDP implementation change xdp_do_flush_map
to xdp_do_flush.

Fixes: 9cbc948b5a ("igb: add XDP support")
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-12-09 15:26:58 -08:00
Sven Auhagen
681429dba9 igb: skb add metasize for xdp
add metasize if it is set in xdp

Fixes: 9cbc948b5a ("igb: add XDP support")
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-12-09 15:26:58 -08:00
Sven Auhagen
2e2bb5594c igb: XDP extack message on error
Add an extack error message when the RX buffer size is too small
for the frame size.

Fixes: 9cbc948b5a ("igb: add XDP support")
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-12-09 15:26:58 -08:00
Sven Auhagen
b829ec1a66 igb: take VLAN double header into account
Increase the packet header padding to include double VLAN tagging.
This patch uses a macro for this.

Fixes: 9cbc948b5a ("igb: add XDP support")
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-12-09 15:26:58 -08:00
Sven Auhagen
cfb33e174f igb: XDP xmit back fix error code
The igb XDP xmit back function should only return
defined error codes.

Fixes: 9cbc948b5a ("igb: add XDP support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-12-09 15:26:57 -08:00
Björn Töpel
b02e5a0ebb xsk: Propagate napi_id to XDP socket Rx path
Add napi_id to the xdp_rxq_info structure, and make sure the XDP
socket pick up the napi_id in the Rx path. The napi_id is used to find
the corresponding NAPI structure for socket busy polling.

Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/bpf/20201130185205.196029-7-bjorn.topel@gmail.com
2020-12-01 00:09:25 +01:00
Sebastian Andrzej Siewior
0171f4e8d3 net: intel: Remove in_interrupt() warnings
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and a tree wide
effort to clean up and consolidate the (ab)usage of in_interrupt() and
related checks is happening.

In this case the checks cover only parts of the contexts in which these
functions cannot be called. They fail to detect preemption or interrupt
disabled invocations.

As the functions which are invoked from the various places contain already
a broad variety of checks (always enabled or debug option dependent) cover
all invalid conditions already, there is no point in having inconsistent
warnings in those drivers.

Just remove them.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-29 14:02:54 -07:00
Gal Hammer
2fc1d8ee1e igb: read PBA number from flash
Fixed flash presence check for 82576 controllers so the part
number string is read and displayed correctly.

Signed-off-by: Gal Hammer <ghammer@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-09-28 14:42:45 -07:00
Sven Auhagen
9cbc948b5a igb: add XDP support
Add XDP support to the IGB driver.
The implementation follows the IXGBE XDP implementation
closely and I used the following patches as basis:

1. commit 9247080816 ("ixgbe: add XDP support for pass and drop actions")
2. commit 33fdc82f08 ("ixgbe: add support for XDP_TX action")
3. commit ed93a39871 ("ixgbe: tweak page counting for XDP_REDIRECT")

Due to the hardware constraints of the devices using the
IGB driver we must share the TX queues with XDP which
means locking the TX queue for XDP.

I ran tests on an older device to get better numbers.
Test machine:

Intel(R) Atom(TM) CPU C2338 @ 1.74GHz (2 Cores)
2x Intel I211

Routing Original Driver Network Stack: 382 Kpps

Routing XDP Redirect (xdp_fwd_kern): 1.48 Mpps
XDP Drop: 1.48 Mpps

Using XDP we can achieve line rate forwarding even on
an older Intel Atom CPU.

Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-09-28 14:42:45 -07:00
Jesse Brandeburg
b50f7bca5e intel-ethernet: clean up W=1 warnings in kdoc
This takes care of all of the trivial W=1 fixes in the Intel
Ethernet drivers, which allows developers and maintainers to
build more of the networking tree with more complete warning
checks.

There are three classes of kdoc warnings fixed:
 - cannot understand function prototype: 'x'
 - Excess function parameter 'x' description in 'y'
 - Function parameter or member 'x' not described in 'y'

All of the changes were trivial comment updates on
function headers.

Inspired by Lee Jones' series of wireless work to do the same.
Compile tested only, and passes simple test of
$ git ls-files *.[ch] | egrep drivers/net/ethernet/intel | \
  xargs scripts/kernel-doc -none

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-25 16:28:59 -07:00
Jakub Kicinski
44a8c4f33c Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.

Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-09-04 21:28:59 -07:00
Tariq Toukan
f468f21b7a net: Take common prefetch code structure into a function
Many device drivers use the same prefetch code structure to
deal with small L1 cacheline size.
Take this code into a function and call it from the drivers.

Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-26 15:55:53 -07:00
Gustavo A. R. Silva
df561f6688 treewide: Use fallthrough pseudo-keyword
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-08-23 17:36:59 -05:00
David S. Miller
bd0b33b248 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Resolved kernel/bpf/btf.c using instructions from merge commit
69138b34a7

Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-02 01:02:12 -07:00
Miaohe Lin
8698fb64cc igb: use eth_zero_addr() to clear mac address
Use eth_zero_addr() to clear mac address instead of memset().

Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-07-30 11:41:45 -07:00
Suraj Upadhyay
90105264a6 igb: Remove unnecessary usages of memset
Replace memsets of 1 byte with simple assignment.
Issue found with checkpatch.pl

Signed-off-by: Suraj Upadhyay <usuraj35@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-07-30 10:51:25 -07:00
Francesco Ruggeri
024a8168b7 igb: reinit_locked() should be called with rtnl_lock
We observed two panics involving races with igb_reset_task.
The first panic is caused by this race condition:

	kworker			reboot -f

	igb_reset_task
	igb_reinit_locked
	igb_down
	napi_synchronize
				__igb_shutdown
				igb_clear_interrupt_scheme
				igb_free_q_vectors
				igb_free_q_vector
				adapter->q_vector[v_idx] = NULL;
	napi_disable
	Panics trying to access
	adapter->q_vector[v_idx].napi_state

The second panic (a divide error) is caused by this race:

kworker		reboot -f	tx packet

igb_reset_task
		__igb_shutdown
		rtnl_lock()
		...
		igb_clear_interrupt_scheme
		igb_free_q_vectors
		adapter->num_tx_queues = 0
		...
		rtnl_unlock()
rtnl_lock()
igb_reinit_locked
igb_down
igb_up
netif_tx_start_all_queues
				dev_hard_start_xmit
				igb_xmit_frame
				igb_tx_queue_mapping
				Panics on
				r_idx % adapter->num_tx_queues

This commit applies to igb_reset_task the same changes that
were applied to ixgbe in commit 2f90b8657e ("ixgbe: this patch
adds support for DCB to the kernel and ixgbe driver"),
commit 8f4c5c9fb8 ("ixgbe: reinit_locked() should be called with
rtnl_lock") and commit 88adce4ea8 ("ixgbe: fix possible race in
reset subtask").

Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-07-30 10:05:14 -07:00
Jeff Kirsher
5463fce643 ethernet/intel: Convert fallthrough code comments
Convert all the remaining 'fall through" code comments to the newer
'fallthrough;' keyword.

Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-07-01 13:47:43 -07:00
Jeff Kirsher
34a2a3b83e net/intel: remove driver versions from Intel drivers
As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.

For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running.  So we now pass the
value of UTS_RELEASE to the firmware.  This adminq call is required per
the HAS document.  The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.

What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.

CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
2020-06-25 22:25:13 -07:00
Linus Torvalds
cb8e59cc87 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from David Miller:

 1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
    Augusto von Dentz.

 2) Add GSO partial support to igc, from Sasha Neftin.

 3) Several cleanups and improvements to r8169 from Heiner Kallweit.

 4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
    device self-test. From Andrew Lunn.

 5) Start moving away from custom driver versions, use the globally
    defined kernel version instead, from Leon Romanovsky.

 6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.

 7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.

 8) Add sriov and vf support to hinic, from Luo bin.

 9) Support Media Redundancy Protocol (MRP) in the bridging code, from
    Horatiu Vultur.

10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.

11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
    Dubroca. Also add ipv6 support for espintcp.

12) Lots of ReST conversions of the networking documentation, from Mauro
    Carvalho Chehab.

13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
    from Doug Berger.

14) Allow to dump cgroup id and filter by it in inet_diag code, from
    Dmitry Yakunin.

15) Add infrastructure to export netlink attribute policies to
    userspace, from Johannes Berg.

16) Several optimizations to sch_fq scheduler, from Eric Dumazet.

17) Fallback to the default qdisc if qdisc init fails because otherwise
    a packet scheduler init failure will make a device inoperative. From
    Jesper Dangaard Brouer.

18) Several RISCV bpf jit optimizations, from Luke Nelson.

19) Correct the return type of the ->ndo_start_xmit() method in several
    drivers, it's netdev_tx_t but many drivers were using
    'int'. From Yunjian Wang.

20) Add an ethtool interface for PHY master/slave config, from Oleksij
    Rempel.

21) Add BPF iterators, from Yonghang Song.

22) Add cable test infrastructure, including ethool interfaces, from
    Andrew Lunn. Marvell PHY driver is the first to support this
    facility.

23) Remove zero-length arrays all over, from Gustavo A. R. Silva.

24) Calculate and maintain an explicit frame size in XDP, from Jesper
    Dangaard Brouer.

25) Add CAP_BPF, from Alexei Starovoitov.

26) Support terse dumps in the packet scheduler, from Vlad Buslov.

27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.

28) Add devm_register_netdev(), from Bartosz Golaszewski.

29) Minimize qdisc resets, from Cong Wang.

30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
    eliminate set_fs/get_fs calls. From Christoph Hellwig.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
  selftests: net: ip_defrag: ignore EPERM
  net_failover: fixed rollback in net_failover_open()
  Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
  Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
  vmxnet3: allow rx flow hash ops only when rss is enabled
  hinic: add set_channels ethtool_ops support
  selftests/bpf: Add a default $(CXX) value
  tools/bpf: Don't use $(COMPILE.c)
  bpf, selftests: Use bpf_probe_read_kernel
  s390/bpf: Use bcr 0,%0 as tail call nop filler
  s390/bpf: Maintain 8-byte stack alignment
  selftests/bpf: Fix verifier test
  selftests/bpf: Fix sample_cnt shared between two threads
  bpf, selftests: Adapt cls_redirect to call csum_level helper
  bpf: Add csum_level helper for fixing up csum levels
  bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
  sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
  crypto/chtls: IPv6 support for inline TLS
  Crypto/chcr: Fixes a coccinile check error
  Crypto/chcr: Fixes compilations warnings
  ...
2020-06-03 16:27:18 -07:00
Jason Yan
49c65e95f3 igb: make igb_set_fc_watermarks() return void
This function always return 0 now, we can make it return void to
simplify the code. This fixes the following coccicheck warning:

drivers/net/ethernet/intel/igb/e1000_mac.c:728:5-12: Unneeded variable:
"ret_val". Return "0" on line 751

Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-28 20:04:01 -07:00
Kai-Heng Feng
165ae7a8fe igb: Report speed and duplex as unknown when device is runtime suspended
igb device gets runtime suspended when there's no link partner. We can't
get correct speed under that state:
$ cat /sys/class/net/enp3s0/speed
1000

In addition to that, an error can also be spotted in dmesg:
[  385.991957] igb 0000:03:00.0 enp3s0: PCIe link lost

Since device can only be runtime suspended when there's no link partner,
we can skip reading register and let the following logic set speed and
duplex with correct status.

The more generic approach will be wrap get_link_ksettings() with begin()
and complete() callbacks. However, for this particular issue, begin()
calls igb_runtime_resume() , which tries to rtnl_lock() while the lock
is already hold by upper ethtool layer.

So let's take this approach until the igb_runtime_resume() no longer
needs to hold rtnl_lock.

CC: stable <stable@vger.kernel.org>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-22 18:21:52 -07:00
Rafael J. Wysocki
e07515563d PM: sleep: core: Rename DPM_FLAG_NEVER_SKIP
Rename DPM_FLAG_NEVER_SKIP to DPM_FLAG_NO_DIRECT_COMPLETE which
matches its purpose more closely.

No functional impact.

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # for PCI parts
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
2020-04-24 21:33:09 +02:00
Wolfram Sang
07eaf53adb igb: convert to use i2c_new_client_device()
Move away from the deprecated API and return the shiny new ERRPTR where
useful.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-26 19:31:21 -07:00
Jakub Kicinski
a289108c2a net: igb: let core reject the unsupported coalescing parameters
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver was rejecting almost all unsupported
parameters already, it was only missing a check
for tx_max_coalesced_frames_irq.

As a side effect of these changes the error code for
unsupported params changes from ENOTSUPP to EOPNOTSUPP.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-12 11:32:36 -07:00
Gustavo A. R. Silva
040efdb14c intel: Replace zero-length array with flexible-array member
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-24 15:26:17 -08:00
David S. Miller
b3f7e3f23a Merge ra.kernel.org:/pub/scm/linux/kernel/git/netdev/net 2020-01-19 22:10:04 +01:00
Manfred Rudigier
5365ec1aef igb: Fix SGMII SFP module discovery for 100FX/LX.
Changing the link mode should also be done for 100BaseFX SGMII modules,
otherwise they just don't work when the default link mode in CTRL_EXT
coming from the EEPROM is SERDES.

Additionally 100Base-LX SGMII SFP modules are also supported now, which
was not the case before.

Tested with an i210 using Flexoptix S.1303.2M.G 100FX and
S.1303.10.G 100LX SGMII SFP modules.

Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-01-09 09:21:40 -08:00
Robert Beckett
6506f52dcb igb: dont drop packets if rx flow control is enabled
If Rx flow control has been enabled (via autoneg or forced), packets
should not be dropped due to Rx descriptor ring exhaustion. Instead
pause frames should be used to apply back pressure. This only applies
if VFs are not in use.

Move SRRCTL setup to its own function for easy reuse and only set drop
enable bit if Rx flow control is not enabled.

Since v1: always enable dropping of packets if VFs in use.

Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-12-31 11:17:25 -08:00
David S. Miller
ac80010fc9 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Mere overlapping changes in the conflicts here.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-22 15:15:05 -08:00
Michael S. Tsirkin
0290bd291c netdev: pass the stuck queue to the timeout handler
This allows incrementing the correct timeout statistic without any mess.
Down the road, devices can learn to reset just the specific queue.

The patch was generated with the following script:

use strict;
use warnings;

our $^I = '.bak';

my @work = (
["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"],
["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"],
["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"],
["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"],
["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"],
["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"],
["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"],
["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"],
["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"],
["drivers/net/appletalk/cops.c", "cops_timeout"],
["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"],
["drivers/net/arcnet/arcnet.c", "arcnet_timeout"],
["drivers/net/arcnet/com20020.c", "arcnet_timeout"],
["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"],
["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"],
["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"],
["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"],
["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"],
["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"],
["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"],
["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"],
["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"],
["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"],
["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"],
["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"],
["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"],
["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"],
["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"],
["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"],
["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"],
["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"],
["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"],
["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"],
["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"],
["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"],
["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"],
["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"],
["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"],
["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"],
["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"],
["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"],
["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"],
["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"],
["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"],
["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"],
["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"],
["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"],
["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"],
["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"],
["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"],
["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"],
["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"],
["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"],
["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"],
["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"],
["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"],
["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"],
["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"],
["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"],
["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"],
["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"],
["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"],
["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"],
["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"],
["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"],
["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"],
["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"],
["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"],
["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"],
["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"],
["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"],
["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"],
["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"],
["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"],
["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"],
["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"],
["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"],
["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"],
["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"],
["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"],
["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"],
["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"],
["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"],
["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"],
["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"],
["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"],
["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"],
["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"],
["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"],
["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"],
["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"],
["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"],
["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"],
["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"],
["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"],
["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"],
["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"],
["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"],
["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"],
["drivers/net/ethernet/jme.c", "jme_tx_timeout"],
["drivers/net/ethernet/korina.c", "korina_tx_timeout"],
["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"],
["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"],
["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"],
["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"],
["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"],
["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"],
["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"],
["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"],
["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"],
["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"],
["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"],
["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"],
["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"],
["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"],
["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"],
["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"],
["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"],
["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"],
["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"],
["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"],
["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"],
["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"],
["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"],
["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"],
["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"],
["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"],
["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"],
["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"],
["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"],
["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"],
["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"],
["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"],
["drivers/net/ethernet/realtek/atp.c", "tx_timeout"],
["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"],
["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"],
["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"],
["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"],
["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"],
["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"],
["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"],
["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"],
["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"],
["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"],
["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"],
["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"],
["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"],
["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"],
["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"],
["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"],
["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"],
["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"],
["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"],
["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"],
["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"],
["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"],
["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"],
["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"],
["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"],
["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"],
["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"],
["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"],
["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"],
["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"],
["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"],
["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"],
["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"],
["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"],
["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"],
["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"],
["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"],
["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"],
["drivers/net/slip/slip.c", "sl_tx_timeout"],
["include/linux/usb/usbnet.h", "usbnet_tx_timeout"],
["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"],
["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"],
["drivers/net/usb/catc.c", "catc_tx_timeout"],
["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"],
["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"],
["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"],
["drivers/net/usb/hso.c", "hso_net_tx_timeout"],
["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"],
["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"],
["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"],
["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"],
["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"],
["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"],
["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"],
["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"],
["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"],
["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"],
["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"],
["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"],
["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"],
["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"],
["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"],
["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"],
["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"],
["drivers/net/wan/cosa.c", "cosa_net_timeout"],
["drivers/net/wan/farsync.c", "fst_tx_timeout"],
["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"],
["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"],
["drivers/net/wan/x25_asy.c", "x25_asy_timeout"],
["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"],
["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"],
["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"],
["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"],
["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"],
["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"],
["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"],
["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"],
["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"],
["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"],
["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"],
["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"],
["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"],
["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"],
["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"],
["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"],
["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"],
["drivers/tty/synclink.c", "hdlcdev_tx_timeout"],
["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"],
["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"],
["net/atm/lec.c", "lec_tx_timeout"],
["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"]
);

for my $p (@work) {
	my @pair = @$p;
	my $file = $pair[0];
	my $func = $pair[1];
	print STDERR $file , ": ", $func,"\n";
	our @ARGV = ($file);
	while (<ARGV>) {
		if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) {
			print STDERR "found $1+$2 in $file\n";
		}
		if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) {
			print STDERR "$func found in $file\n";
		}
		print;
	}
}

where the list of files and functions is simply from:

git grep ndo_tx_timeout, with manual addition of headers
in the rare cases where the function is from a header,
then manually changing the few places which actually
call ndo_tx_timeout.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Martin Habets <mhabets@solarflare.com>

changes from v9:
	fixup a forward declaration
changes from v9:
	more leftovers from v3 change
changes from v8:
        fix up a missing direct call to timeout
        rebased on net-next
changes from v7:
	fixup leftovers from v3 change
changes from v6:
	fix typo in rtl driver
changes from v5:
	add missing files (allow any net device argument name)
changes from v4:
	add a missing driver header
changes from v3:
        change queue # to unsigned
Changes from v2:
        added headers
Changes from v1:
        Fix errors found by kbuild:
        generalize the pattern a bit, to pick up
        a couple of instances missed by the previous
        version.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-12 21:38:57 -08:00
Pankaj Bharadiya
c593642c8b treewide: Use sizeof_field() macro
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().

This patch is generated using following script:

EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"

git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do

	if [[ "$file" =~ $EXCLUDE_FILES ]]; then
		continue
	fi
	sed -i  -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done

Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
2019-12-09 10:36:44 -08:00
David S. Miller
19b7e21c55 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Lots of overlapping changes and parallel additions, stuff
like that.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-16 21:51:42 -08:00
Richard Cochran
5a450eb388 igb: Reject requests that fail to enable time stamping on both edges.
This hardware always time stamps rising and falling edges, and so this
patch validates that the request does contains both edges.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15 12:48:32 -08:00
Richard Cochran
6138e687c7 ptp: Introduce strict checking of external time stamp options.
User space may request time stamps on rising edges, falling edges, or
both.  However, the particular mode may or may not be supported in the
hardware or in the driver.  This patch adds a "strict" flag that tells
drivers to ensure that the requested mode will be honored.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15 12:48:32 -08:00
Jacob Keller
6edd110b41 igb: reject unsupported external timestamp flags
Fix the igb PTP support to explicitly reject any future flags that
get added to the external timestamp request ioctl.

In order to maintain currently functioning code, this patch accepts all
three current flags. This is because the PTP_RISING_EDGE and
PTP_FALLING_EDGE flags have unclear semantics and each driver seems to
have interpreted them slightly differently.

This HW always time stamps both edges:

  flags                                                 Meaning
  ----------------------------------------------------  --------------------------
  PTP_ENABLE_FEATURE                                    Time stamp both edges
  PTP_ENABLE_FEATURE|PTP_RISING_EDGE                    Time stamp both edges
  PTP_ENABLE_FEATURE|PTP_FALLING_EDGE                   Time stamp both edges
  PTP_ENABLE_FEATURE|PTP_RISING_EDGE|PTP_FALLING_EDGE   Time stamp both edges

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15 12:48:32 -08:00
Jacob Keller
7f9048f1df net: reject PTP periodic output requests with unsupported flags
Commit 823eb2a3c4 ("PTP: add support for one-shot output") introduced
a new flag for the PTP periodic output request ioctl. This flag is not
currently supported by any driver.

Fix all drivers which implement the periodic output request ioctl to
explicitly reject any request with flags they do not understand. This
ensures that the driver does not accidentally misinterpret the
PTP_PEROUT_ONE_SHOT flag, or any new flag introduced in the future.

This is important for forward compatibility: if a new flag is
introduced, the driver should reject requests to enable the flag until
the driver has actually been modified to support the flag in question.

Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Christopher Hall <christopher.s.hall@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15 12:48:32 -08:00
David S. Miller
14684b9301 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-09 11:04:37 -08:00
Jacob Keller
6acab13bdf igb/igc: use ktime accessors for skb->tstamp
When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.

Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.

Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.

This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-11-08 16:10:51 -08:00
Florian Fainelli
12299132b3 net: ethernet: intel: Demote MTU change prints to debug
Changing a network device MTU can be a fairly frequent operation, and
failure to change the MTU is reflected to user-space properly, both by
an appropriate message as well as by looking at whether the device's MTU
matches the configuration.

Demote the prints to debug prints by using netdev_dbg(), making all
Intel wired LAN drivers consistent, since they used a mixture of PCI
device and network device prints before.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-07 20:01:14 -08:00
David S. Miller
d31e95585c Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.

The rest were (relatively) trivial in nature.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-02 13:54:56 -07:00
Manfred Rudigier
8d5cfd7f76 igb: Fix constant media auto sense switching when no cable is connected
At least on the i350 there is an annoying behavior that is maybe also
present on 82580 devices, but was probably not noticed yet as MAS is not
widely used.

If no cable is connected on both fiber/copper ports the media auto sense
code will constantly swap between them as part of the watchdog task and
produce many unnecessary kernel log messages.

The swap code responsible for this behavior (switching to fiber) should
not be executed if the current media type is copper and there is no signal
detected on the fiber port. In this case we can safely wait until the
AUTOSENSE_EN bit is cleared.

Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-11-01 13:20:00 -07:00
Manfred Rudigier
fb2308ba16 igb: Enable media autosense for the i350.
This patch enables the hardware feature "Media Auto Sense" also on the
i350. It works in the same way as on the 82850 devices. Hardware designs
using dual PHYs (fiber/copper) can enable this feature by setting the MAS
enable bits in the NVM_COMPAT register (0x03) in the EEPROM.

Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-10-31 14:03:16 -07:00
Lyude Paul
94bc1e522b igb/igc: Don't warn on fatal read failures when the device is removed
Fatal read errors are worth warning about, unless of course the device
was just unplugged from the machine - something that's a rather normal
occurrence when the igb/igc adapter is located on a Thunderbolt dock. So,
let's only WARN() if there's a fatal read error while the device is
still present.

This fixes the following WARN splat that's been appearing whenever I
unplug my Caldigit TS3 Thunderbolt dock from my laptop:

  igb 0000:09:00.0 enp9s0: PCIe link lost
  ------------[ cut here ]------------
  igb: Failed to read reg 0x18!
  WARNING: CPU: 7 PID: 516 at
  drivers/net/ethernet/intel/igb/igb_main.c:756 igb_rd32+0x57/0x6a [igb]
  Modules linked in: igb dca thunderbolt fuse vfat fat elan_i2c mei_wdt
  mei_hdcp i915 wmi_bmof intel_wmi_thunderbolt iTCO_wdt
  iTCO_vendor_support x86_pkg_temp_thermal intel_powerclamp joydev
  coretemp crct10dif_pclmul crc32_pclmul i2c_algo_bit ghash_clmulni_intel
  intel_cstate drm_kms_helper intel_uncore syscopyarea sysfillrect
  sysimgblt fb_sys_fops intel_rapl_perf intel_xhci_usb_role_switch mei_me
  drm roles idma64 i2c_i801 ucsi_acpi typec_ucsi mei intel_lpss_pci
  processor_thermal_device typec intel_pch_thermal intel_soc_dts_iosf
  intel_lpss int3403_thermal thinkpad_acpi wmi int340x_thermal_zone
  ledtrig_audio int3400_thermal acpi_thermal_rel acpi_pad video
  pcc_cpufreq ip_tables serio_raw nvme nvme_core crc32c_intel uas
  usb_storage e1000e i2c_dev
  CPU: 7 PID: 516 Comm: kworker/u16:3 Not tainted 5.2.0-rc1Lyude-Test+ #14
  Hardware name: LENOVO 20L8S2N800/20L8S2N800, BIOS N22ET35W (1.12 ) 04/09/2018
  Workqueue: kacpi_hotplug acpi_hotplug_work_fn
  RIP: 0010:igb_rd32+0x57/0x6a [igb]
  Code: 87 b8 fc ff ff 48 c7 47 08 00 00 00 00 48 c7 c6 33 42 9b c0 4c 89
  c7 e8 47 45 cd dc 89 ee 48 c7 c7 43 42 9b c0 e8 c1 94 71 dc <0f> 0b eb
  08 8b 00 ff c0 75 b0 eb c8 44 89 e0 5d 41 5c c3 0f 1f 44
  RSP: 0018:ffffba5801cf7c48 EFLAGS: 00010286
  RAX: 0000000000000000 RBX: ffff9e7956608840 RCX: 0000000000000007
  RDX: 0000000000000000 RSI: ffffba5801cf7b24 RDI: ffff9e795e3d6a00
  RBP: 0000000000000018 R08: 000000009dec4a01 R09: ffffffff9e61018f
  R10: 0000000000000000 R11: ffffba5801cf7ae5 R12: 00000000ffffffff
  R13: ffff9e7956608840 R14: ffff9e795a6f10b0 R15: 0000000000000000
  FS:  0000000000000000(0000) GS:ffff9e795e3c0000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000564317bc4088 CR3: 000000010e00a006 CR4: 00000000003606e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   igb_release_hw_control+0x1a/0x30 [igb]
   igb_remove+0xc5/0x14b [igb]
   pci_device_remove+0x3b/0x93
   device_release_driver_internal+0xd7/0x17e
   pci_stop_bus_device+0x36/0x75
   pci_stop_bus_device+0x66/0x75
   pci_stop_bus_device+0x66/0x75
   pci_stop_and_remove_bus_device+0xf/0x19
   trim_stale_devices+0xc5/0x13a
   ? __pm_runtime_resume+0x6e/0x7b
   trim_stale_devices+0x103/0x13a
   ? __pm_runtime_resume+0x6e/0x7b
   trim_stale_devices+0x103/0x13a
   acpiphp_check_bridge+0xd8/0xf5
   acpiphp_hotplug_notify+0xf7/0x14b
   ? acpiphp_check_bridge+0xf5/0xf5
   acpi_device_hotplug+0x357/0x3b5
   acpi_hotplug_work_fn+0x1a/0x23
   process_one_work+0x1a7/0x296
   worker_thread+0x1a8/0x24c
   ? process_scheduled_works+0x2c/0x2c
   kthread+0xe9/0xee
   ? kthread_destroy_worker+0x41/0x41
   ret_from_fork+0x35/0x40
  ---[ end trace 252bf10352c63d22 ]---

Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 47e16692b2 ("igb/igc: warn when fatal read failure happens")
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Acked-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-10-31 14:03:16 -07:00
Josh Hunt
4085d06d2f igb: Add UDP segmentation offload support
Based on a series from Alexander Duyck this change adds UDP segmentation
offload support to the igb driver.

CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Josh Hunt <johunt@akamai.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-10-29 21:05:33 -07:00
Markus Elfring
399e06a517 ethernet: Delete unnecessary checks before the macro call “dev_kfree_skb”
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-22 16:22:04 -07:00
Chuhong Yuan
5daab287c6 igb: Use dev_get_drvdata where possible
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-23 13:02:42 -07:00
Matthew Wilcox (Oracle)
d7840976e3 net: Use skb accessors in network drivers
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.

Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-22 20:47:56 -07:00
Pablo Neira Ayuso
f9e30088d2 net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
And any other existing fields in this structure that refer to tc.
Specifically:

* tc_cls_flower_offload_flow_rule() to flow_cls_offload_flow_rule().
* TC_CLSFLOWER_* to FLOW_CLS_*.
* tc_cls_common_offload to tc_cls_common_offload.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-09 14:38:51 -07:00
Pablo Neira Ayuso
955bcb6ea0 drivers: net: use flow block API
This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.

This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.

Remove tc_block_offload alias.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-09 14:38:50 -07:00
Pablo Neira Ayuso
4e95bc268b net: flow_offload: add flow_block_cb_setup_simple()
Most drivers do the same thing to set up the flow block callbacks, this
patch adds a helper function to do this.

This preparation patch reduces the number of changes to adapt the
existing drivers to use the flow block callback API.

This new helper function takes a flow block list per-driver, which is
set to NULL until this driver list is used.

This patch also introduces the flow_block_command and
flow_block_binder_type enumerations, which are renamed to use
FLOW_BLOCK_* in follow up patches.

There are three definitions (aliases) in order to reduce the number of
updates in this patch, which go away once drivers are fully adapted to
use this flow block API.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-09 14:38:50 -07:00
David S. Miller
11697cfc71 Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2019-06-28

This series contains a smorgasbord of updates to many of the Intel
drivers.

Gustavo A. R. Silva updates the ice and iavf drivers to use the
strcut_size() helper where possible.

Miguel increases the pause and refresh time for flow control in the
e1000e driver during reset for certain devices.

Dann Frazier fixes a potential NULL pointer dereference in ixgbe driver
when using non-IPSec enabled devices.

Colin Ian King fixes a potential overflow during a shift in the ixgbe
driver.  Also fixes a potential NULL pointer dereference in the iavf
driver by adding a check.

Venkatesh Srinivas converts the e1000 driver to use dma_wmb() instead of
wmb() for doorbell writes to avoid SFENCEs in the transmit and receive
paths.

Arjan updates the e1000e driver to improve boot time by over 100 msec by
reducing the usleep ranges suring system startup.

Artem updates the igb driver register dump in ethtool, first prepares
the register dump for future additions of registers in the dump, then
secondly, adds the RR2DCDELAY register to the dump.  When dealing with
time-sensitive networks, this register is helpful in determining your
latency from the device to the ring.

Alex fixes the ixgbevf driver to use the current cached link state,
rather than trying to re-check the value from the PF.

Harshitha adds support for MACVLAN offloads in i40e by using channels as
MACVLAN interfaces.

Detlev Casanova updates the e1000e driver to use delayed work instead of
timers to run the watchdog.

Vitaly fixes an issue in e1000e, where when disconnecting and
reconnecting the physical cable connection, the NIC enters a DMoff
state.  This state causes a mismatch in link and duplexing, so check the
PCIm function state and perform a PHY reset when in this state to
resolve the issue.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-30 16:03:35 -07:00
Artem Bityutskiy
cd502a7f7c igb: add RR2DCDELAY to ethtool registers dump
This patch adds the RR2DCDELAY register to the ethtool registers dump.
RR2DCDELAY exists on I210 and I211 Intel Gigabit Ethernet chips and it stands
for "Read Request To Data Completion Delay". Here is how this register is
described in the I210 datasheet:

"This field captures the maximum PCIe split time in 16 ns units, which is the
maximum delay between the read request to the first data completion. This is
giving an estimation of the PCIe round trip time."

In other words, whenever I210 reads from the host memory (e.g., fetches a
descriptor from the ring), the chip measures every PCI DMA read transaction and
captures the maximum value. So it ends up containing the longest DMA
transaction time.

This register is very useful for troubleshooting and research purposes. If you
are dealing with time-sensitive networks, this register can help you get
an idea of your "I210-to-ring" latency. This helps answering questions like
"should I have PCIe ASPM enabled?" or "should I enable deep C-states?" on
my system.

It is safe to read this register at any point, reading it has no effect on
the I210 chip functionality.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-06-28 16:00:06 -07:00
Artem Bityutskiy
9379b39945 igb: minor ethool regdump amendment
This patch has no functional impact and it is just a preparation
for the following patch. It removes an early return from the
'igb_get_regs()' function by moving the 82576-only registers
dump into an "if" block. With this preparation, we can dump more
non-82576 registers at the end of this function.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-06-28 16:00:00 -07:00
Vedang Patel
1e08511d5d igb: clear out skb->tstamp after reading the txtime
If a packet which is utilizing the launchtime feature (via SO_TXTIME socket
option) also requests the hardware transmit timestamp, the hardware
timestamp is not delivered to the userspace. This is because the value in
skb->tstamp is mistaken as the software timestamp.

Applications, like ptp4l, request a hardware timestamp by setting the
SOF_TIMESTAMPING_TX_HARDWARE socket option. Whenever a new timestamp is
detected by the driver (this work is done in igb_ptp_tx_work() which calls
igb_ptp_tx_hwtstamps() in igb_ptp.c[1]), it will queue the timestamp in the
ERR_QUEUE for the userspace to read. When the userspace is ready, it will
issue a recvmsg() call to collect this timestamp.  The problem is in this
recvmsg() call. If the skb->tstamp is not cleared out, it will be
interpreted as a software timestamp and the hardware tx timestamp will not
be successfully sent to the userspace. Look at skb_is_swtx_tstamp() and the
callee function __sock_recv_timestamp() in net/socket.c for more details.

Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-28 14:45:33 -07:00
Gustavo A. R. Silva
42277cedba igb: mark expected switch fall-through
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

This patch fixes the following warning:

drivers/net/ethernet/intel/igb/e1000_82575.c: In function ‘igb_get_invariants_82575’:
drivers/net/ethernet/intel/igb/e1000_82575.c:636:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (igb_sgmii_uses_mdio_82575(hw)) {
      ^
drivers/net/ethernet/intel/igb/e1000_82575.c:642:2: note: here
  case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.

Signed-off-by: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-05-28 15:52:37 -07:00
Gustavo A. R. Silva
b7b3ad7aaf igb: mark expected switch fall-through
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

This patch fixes the following warning:

drivers/net/ethernet/intel/igb/igb_main.c: In function ‘__igb_notify_dca’:
drivers/net/ethernet/intel/igb/igb_main.c:6694:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (dca_add_requester(dev) == 0) {
      ^
drivers/net/ethernet/intel/igb/igb_main.c:6701:2: note: here
  case DCA_PROVIDER_REMOVE:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.

Signed-off-by: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-05-28 15:48:42 -07:00
Feng Tang
47e16692b2 igb/igc: warn when fatal read failure happens
Failed in read the HW register is very serious for igb/igc driver,
as its hw_addr will be set to NULL and cause the adapter be seen as
"REMOVED".

We saw the error only a few times in the MTBF test for suspend/resume,
but can hardly get any useful info to debug.

Adding WARN() so that we can get the necessary information about
where and how it happens, and use it for root causing and fixing
this "PCIe link lost issue"

This affects igb, igc.

Signed-off-by: Feng Tang <feng.tang@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-05-28 15:42:32 -07:00
Linus Torvalds
80f232121b Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:
 "Highlights:

   1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.

   2) Add fib_sync_mem to control the amount of dirty memory we allow to
      queue up between synchronize RCU calls, from David Ahern.

   3) Make flow classifier more lockless, from Vlad Buslov.

   4) Add PHY downshift support to aquantia driver, from Heiner
      Kallweit.

   5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
      contention on SLAB spinlocks in heavy RPC workloads.

   6) Partial GSO offload support in XFRM, from Boris Pismenny.

   7) Add fast link down support to ethtool, from Heiner Kallweit.

   8) Use siphash for IP ID generator, from Eric Dumazet.

   9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
      entries, from David Ahern.

  10) Move skb->xmit_more into a per-cpu variable, from Florian
      Westphal.

  11) Improve eBPF verifier speed and increase maximum program size,
      from Alexei Starovoitov.

  12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
      spinlocks. From Neil Brown.

  13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.

  14) Improve link partner cap detection in generic PHY code, from
      Heiner Kallweit.

  15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
      Maguire.

  16) Remove SKB list implementation assumptions in SCTP, your's truly.

  17) Various cleanups, optimizations, and simplifications in r8169
      driver. From Heiner Kallweit.

  18) Add memory accounting on TX and RX path of SCTP, from Xin Long.

  19) Switch PHY drivers over to use dynamic featue detection, from
      Heiner Kallweit.

  20) Support flow steering without masking in dpaa2-eth, from Ioana
      Ciocoi.

  21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
      Pirko.

  22) Increase the strict parsing of current and future netlink
      attributes, also export such policies to userspace. From Johannes
      Berg.

  23) Allow DSA tag drivers to be modular, from Andrew Lunn.

  24) Remove legacy DSA probing support, also from Andrew Lunn.

  25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
      Haabendal.

  26) Add a generic tracepoint for TX queue timeouts to ease debugging,
      from Cong Wang.

  27) More indirect call optimizations, from Paolo Abeni"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
  cxgb4: Fix error path in cxgb4_init_module
  net: phy: improve pause mode reporting in phy_print_status
  dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
  net: macb: Change interrupt and napi enable order in open
  net: ll_temac: Improve error message on error IRQ
  net/sched: remove block pointer from common offload structure
  net: ethernet: support of_get_mac_address new ERR_PTR error
  net: usb: smsc: fix warning reported by kbuild test robot
  staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
  net: dsa: support of_get_mac_address new ERR_PTR error
  net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
  vrf: sit mtu should not be updated when vrf netdev is the link
  net: dsa: Fix error cleanup path in dsa_init_module
  l2tp: Fix possible NULL pointer dereference
  taprio: add null check on sched_nest to avoid potential null pointer dereference
  net: mvpp2: cls: fix less than zero check on a u32 variable
  net_sched: sch_fq: handle non connected flows
  net_sched: sch_fq: do not assume EDT packets are ordered
  net: hns3: use devm_kcalloc when allocating desc_cb
  net: hns3: some cleanup for struct hns3_enet_ring
  ...
2019-05-07 22:03:58 -07:00
Linus Torvalds
dd4e5d6106 Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
 architectures that need it, hide the barrier inside spin_unlock() when
 MMIO has been performed inside the critical section.
 -----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFaUACgkQt6xw3ITB
 YzRICQgAiv7wF/yIbBhDOmCNCAKDO59chvFQWxXWdGk/aAB56kwKAMXJgLOvlMG/
 VRuuLyParTFQETC3jaxKgnO/1hb+PZLDt2Q2KqixtjIzBypKUPWvK2sf6THhSRF1
 GK0DBVUd1rCrWrR815+SPb8el4xXtdBzvAVB+Fx35PXVNpdRdqCkK+EQ6UnXGokm
 rXXHbnfsnquBDtmb4CR4r2beH+aNElXbdt0Kj8VcE5J7f7jTdW3z6Q9WFRvdKmK7
 yrsxXXB2w/EsWXOwFp0SLTV5+fgeGgTvv8uLjDw+SG6t0E0PebxjNAflT7dPrbYL
 WecjKC9WqBxrGY+4ew6YJP70ijLBCw==
 =aC8m
 -----END PGP SIGNATURE-----

Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux

Pull mmiowb removal from Will Deacon:
 "Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())

  Remove mmiowb() from the kernel memory barrier API and instead, for
  architectures that need it, hide the barrier inside spin_unlock() when
  MMIO has been performed inside the critical section.

  The only relatively recent changes have been addressing review
  comments on the documentation, which is in a much better shape thanks
  to the efforts of Ben and Ingo.

  I was initially planning to split this into two pull requests so that
  you could run the coccinelle script yourself, however it's been plain
  sailing in linux-next so I've just included the whole lot here to keep
  things simple"

* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
  docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
  docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
  arch: Remove dummy mmiowb() definitions from arch code
  net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
  i40iw: Redefine i40iw_mmiowb() to do nothing
  scsi/qla1280: Remove stale comment about mmiowb()
  drivers: Remove explicit invocations of mmiowb()
  drivers: Remove useless trailing comments from mmiowb() invocations
  Documentation: Kill all references to mmiowb()
  riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
  powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
  ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
  mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
  sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
  m68k/io: Remove useless definition of mmiowb()
  nds32/io: Remove useless definition of mmiowb()
  x86/io: Remove useless definition of mmiowb()
  arm64/io: Remove useless definition of mmiowb()
  ARM/io: Remove useless definition of mmiowb()
  mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
  ...
2019-05-06 16:57:52 -07:00
Stanislav Fomichev
c43f1255b8 net: pass net_device argument to the eth_get_headlen
Update all users of eth_get_headlen to pass network device, fetch
network namespace from it and pass it down to the flow dissector.
This commit is a noop until administrator inserts BPF flow dissector
program.

Cc: Maxim Krasnyansky <maxk@qti.qualcomm.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2019-04-23 18:36:34 +02:00
Will Deacon
fb24ea52f7 drivers: Remove explicit invocations of mmiowb()
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:

	@mmiowb@
	@@
	- mmiowb();

and invoked as:

$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done

NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.

Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2019-04-08 12:01:02 +01:00
David S. Miller
f83f715195 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Minor comment merge conflict in mlx5.

Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-05 14:14:19 -07:00
Florian Westphal
6b16f9ee89 net: move skb->xmit_more hint to softnet data
There are two reasons for this.

First, the xmit_more flag conceptually doesn't fit into the skb, as
xmit_more is not a property related to the skb.
Its only a hint to the driver that the stack is about to transmit another
packet immediately.

Second, it was only done this way to not have to pass another argument
to ndo_start_xmit().

We can place xmit_more in the softnet data, next to the device recursion.
The recursion counter is already written to on each transmit. The "more"
indicator is placed right next to it.

Drivers can use the netdev_xmit_more() helper instead of skb->xmit_more
to check the "more packets coming" hint.

skb->xmit_more is retained (but always 0) to not cause build breakage.

This change takes care of the simple s/skb->xmit_more/netdev_xmit_more()/
conversions.  Remaining drivers are converted in the next patches.

Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-01 18:35:02 -07:00
Arvind Sankar
dabb8338be igb: Fix WARN_ONCE on runtime suspend
The runtime_suspend device callbacks are not supposed to save
configuration state or change the power state. Commit fb29f76cc566
("igb: Fix an issue that PME is not enabled during runtime suspend")
changed the driver to not save configuration state during runtime
suspend, however the driver callback still put the device into a
low-power state. This causes a warning in the pci pm core and results in
pci_pm_runtime_suspend not calling pci_save_state or pci_finish_runtime_suspend.

Fix this by not changing the power state either, leaving that to pci pm
core, and make the same change for suspend callback as well.

Also move a couple of defines into the appropriate header file instead
of inline in the .c file.

Fixes: fb29f76cc566 ("igb: Fix an issue that PME is not enabled during runtime suspend")
Signed-off-by: Arvind Sankar <niveditas98@gmail.com>
Reviewed-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-03-26 16:12:34 -07:00
Colin Ian King
5aa151922e igb: fix various indentation issues
There are some lines that have indentation issues, fix these

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-03-19 14:35:18 -07:00
Kai-Heng Feng
5b6e13216b igb: Exclude device from suspend direct complete optimization
igb sets different WoL settings in system suspend callback and runtime
suspend callback.

The suspend direct complete optimization leaves igb in runtime suspended
state with wrong WoL setting during system suspend.

To fix this, we need to disable suspend direct complete optimization to
let igb always use suspend callback to set correct WoL during system
suspend.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-03-19 14:23:30 -07:00
Serhey Popovych
b0ddfe2bb2 intel: correct return from set features callback
According to comments in <linux/netdevice.h> we should return either >0
or -errno from ->ndo_set_features() if changing dev->features by itself.

Return 1 in such places to notify netdev_update_features() about applied
changes in dev->features.

Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-03-19 14:18:49 -07:00
Gustavo A. R. Silva
a0feac18b8 igb: use struct_size() helper
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

size = struct_size(instance, entry, count);

This code was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-08 23:03:48 -08:00
Pablo Neira Ayuso
8f2566225a flow_offload: add flow_rule and flow_match structures and use them
This patch wraps the dissector key and mask - that flower uses to
represent the matching side - around the flow_match structure.

To avoid a follow up patch that would edit the same LoCs in the drivers,
this patch also wraps this new flow match structure around the flow rule
object. This new structure will also contain the flow actions in follow
up patches.

This introduces two new interfaces:

	bool flow_rule_match_key(rule, dissector_id)

that returns true if a given matching key is set on, and:

	flow_rule_match_XYZ(rule, &match);

To fetch the matching side XYZ into the match container structure, to
retrieve the key and the mask with one single call.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-06 10:38:25 -08:00
Todd Fujinaka
a865d22d59 igb: Bump version number
With recent changes, need to bump the driver version to reflect the
changes.

Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-02-05 17:28:10 -08:00
David S. Miller
fa7f3a8d56 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Completely minor snmp doc conflict.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-21 14:41:32 -08:00
Petr Machata
87b0984ebf net: Add extack argument to ndo_fdb_add()
Drivers may not be able to support certain FDB entries, and an error
code is insufficient to give clear hints as to the reasons of rejection.

In order to make it possible to communicate the rejection reason, extend
ndo_fdb_add() with an extack argument. Adapt the existing
implementations of ndo_fdb_add() to take the parameter (and ignore it).
Pass the extack parameter when invoking ndo_fdb_add() from rtnl_fdb_add().

Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-17 15:18:47 -08:00
Jeff Kirsher
5642e27bf6 Revert "igb: reduce CPU0 latency when updating statistics"
This reverts commit 59361316af.

Due to problems found in additional testing, this causes an illegal
context switch in the RCU read-side critical section.

CC: Dave Jones <davej@codemonkey.org.uk>
CC: Cong Wang <xiyou.wangcong@gmail.com>
CC: Jan Jablonsky <jan.jablonsky@thalesgroup.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-15 13:33:44 -08:00
Kai-Heng Feng
1fb3a7a75e igb: Fix an issue that PME is not enabled during runtime suspend
I210 ethernet card doesn't wakeup when a cable gets plugged. It's
because its PME is not set.

Since commit 42eca23021 ("PCI: Don't touch card regs after runtime
suspend D3"), if the PCI state is saved, pci_pm_runtime_suspend() stops
calling pci_finish_runtime_suspend(), which enables the PCI PME.

To fix the issue, let's not to save PCI states when it's runtime
suspend, to let the PCI subsystem enables PME.

Fixes: 42eca23021 ("PCI: Don't touch card regs after runtime suspend D3")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-12-20 12:14:23 -08:00
Jesus Sanchez-Palencia
6f9ae17530 igb: Change RXPBSIZE size when setting Qav mode
Section 4.5.9 of the datasheet says that the total size of all packet
buffers combined (TxPB 0 + 1 + 2 + 3 + RxPB + BMC2OS + OS2BMC) must not
exceed 60KB. Today we are configuring a total of 62KB, so reduce the
RxPB from 32KB to 30KB in order to respect that.

The choice of changing RxPBSIZE here is mainly because it seems more
correct to give more priority to the transmit packet buffers over the
receiver ones when running in Qav mode. Also, the BMC2OS and OS2BMC
sizes are already too short.

Signed-off-by: Jesus Sanchez-Palencia <jesus.s.palencia@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-12-20 11:45:10 -08:00
Jeff Kirsher
59361316af igb: reduce CPU0 latency when updating statistics
This change is based off of the work and suggestion of Jan Jablonsky
<jan.jablonsky@thalesgroup.com>.

The Watchdog workqueue in igb driver is scheduled every 2s for each
network interface. That includes updating a statistics protected by
spinlock. Function igb_update_stats in this case will be protected
against preemption. According to number of a statistics registers
(cca 60), processing this function might cause additional cpu load
 on CPU0.

In case of statistics spinlock may be replaced with mutex, which
reduce latency on CPU0.

CC: Bernhard Kaindl  <bernhard.kaindl@thalesgroup.com>
CC: Jan Jablonsky <jan.jablonsky@thalesgroup.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-12-20 11:02:06 -08:00
David S. Miller
e561bb29b6 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-28 22:10:54 -08:00
Yunjian Wang
e4c39f7926 igb: fix uninitialized variables
This patch fixes the variable 'phy_word' may be used uninitialized.

Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-11-28 08:27:47 -08:00
Jesse Brandeburg
0bcd952fee ethernet/intel: consolidate NAPI and NAPI exit
While reviewing code, I noticed that Eric Dumazet recommends that
drivers check the return code of napi_complete_done, and use that
to decide to enable interrupts or not when exiting poll.  One of
the Intel drivers was already fixed (ixgbe).

Upon looking at the Intel drivers as a whole, we are handling our
polling and NAPI exit in a few different ways based on whether we
have multiqueue and whether we have Tx cleanup included. Several
drivers had the bug of exiting NAPI with return 0, which appears
to mess up the accounting in the stack.

Consolidate all the NAPI routines to do best known way of exiting
and to just mostly look like each other.
1) check return code of napi_complete_done to control interrupt enable
2) return the actual amount of work done.
3) return budget immediately if need NAPI poll again

Tested the changes on e1000e with a high interrupt rate set, and
it shows about an 8% reduction in the CPU utilization when busy
polling because we aren't re-enabling interrupts when we're about
to be polled.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-11-21 10:35:23 -08:00
Joe Perches
4df3c543a7 igb: Fix format with line continuation whitespace
The line continuation unintentionally adds whitespace so
instead use a coalesced format to remove the whitespace.

Miscellanea:

o Use a more typical style for ternaries and arguments
  for this logging message

Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-11-21 10:22:10 -08:00