Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
tools/testing/selftests/drivers/net/ping.py
75cc19c8ff ("selftests: drv-net: add xdp cases for ping.py")
de94e86974 ("selftests: drv-net: store addresses in dict indexed by ipver")
https://lore.kernel.org/netdev/20250311115758.17a1d414@canb.auug.org.au/
net/core/devmem.c
a70f891e0f ("net: devmem: do not WARN conditionally after netdev_rx_queue_restart()")
1d22d3060b ("net: drop rtnl_lock for queue_mgmt operations")
https://lore.kernel.org/netdev/20250313114929.43744df1@canb.auug.org.au/
Adjacent changes:
tools/testing/selftests/net/Makefile
6f50175cca ("selftests: Add IPv6 link-local address generation tests for GRE devices.")
2e5584e0f9 ("selftests/net: expand cmsg_ipv6.sh with ipv4")
drivers/net/ethernet/broadcom/bnxt/bnxt.c
661958552e ("eth: bnxt: do not use BNXT_VNIC_NTUPLE unconditionally in queue restart logic")
fe96d717d3 ("bnxt_en: Extend queue stop/start for TX rings")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ATU Load operations could fail silently if there's not enough space
on the device to hold the new entry. When this happens, the symptom
depends on the unknown flood settings. If unknown multicast flood is
disabled, the multicast packets are dropped when the ATU table is
full. If unknown multicast flood is enabled, the multicast packets
will be flooded to all ports. Either way, IGMP snooping is broken
when the ATU Load operation fails silently.
Do a Read-After-Write verification after each fdb/mdb add operation
to make sure that the operation was really successful, and return
-ENOSPC otherwise.
Fixes: defb05b9b9 ("net: dsa: mv88e6xxx: Add support for fdb_add, fdb_del, and fdb_getnext")
Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250306172306.3859214-1-Joseph.Huang@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As all PCS are using the neg_mode parameter rather than the legacy
an_mode, remove the ability to use the legacy an_mode. We remove the
tests in the phylink code, unconditionally passing the PCS neg_mode
parameter to PCS methods, and remove setting the flag from drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tidPn-0040hd-2R@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Core
----
- More core refactoring to reduce the RTNL lock contention,
including preparatory work for the per-network namespace RTNL lock,
replacing RTNL lock with a per device-one to protect NAPI-related
net device data and moving synchronize_net() calls outside such
lock.
- Extend drop reasons usage, adding net scheduler, AF_UNIX, bridge and
more specific TCP coverage.
- Reduce network namespace tear-down time by removing per-subsystems
synchronize_net() in tipc and sched.
- Add flow label selector support for fib rules, allowing traffic
redirection based on such header field.
Netfilter
---------
- Do not remove netdev basechain when last device is gone, allowing
netdev basechains without devices.
- Revisit the flowtable teardown strategy, dealing better with fin,
reset and re-open events.
- Scale-up IP-vs connection dumping by avoiding linear search on
each restart.
Protocols
---------
- A significant XDP socket refactor, consolidating and optimizing
several helpers into the core
- Better scaling of ICMP rate-limiting, by removing false-sharing in
inet peers handling.
- Introduces netlink notifications for multicast IPv4 and IPv6
address changes.
- Add ipsec support for IP-TFS/AggFrag encapsulation, allowing
aggregation and fragmentation of the inner IP.
- Add sysctl to configure TIME-WAIT reuse delay for TCP sockets,
to avoid local port exhaustion issues when the average connection
lifetime is very short.
- Support updating keys (re-keying) for connections using kernel
TLS (for TLS 1.3 only).
- Support ipv4-mapped ipv6 address clients in smc-r v2.
- Add support for jumbo data packet transmission in RxRPC sockets,
gluing multiple data packets in a single UDP packet.
- Support RxRPC RACK-TLP to manage packet loss and retransmission in
conjunction with the congestion control algorithm.
Driver API
----------
- Introduce a unified and structured interface for reporting PHY
statistics, exposing consistent data across different H/W via
ethtool.
- Make timestamping selectable, allow the user to select the desired
hwtstamp provider (PHY or MAC) administratively.
- Add support for configuring a header-data-split threshold (HDS)
value via ethtool, to deal with partial or buggy H/W implementation.
- Consolidate DSA drivers Energy Efficiency Ethernet support.
- Add EEE management to phylink, making use of the phylib
implementation.
- Add phylib support for in-band capabilities negotiation.
- Simplify how phylib-enabled mac drivers expose the supported
interfaces.
Tests and tooling
-----------------
- Make the YNL tool package-friendly to make it easier to deploy it
separately from the kernel.
- Increase TCP selftest coverage importing several packetdrill
test-cases.
- Regenerate the ethtool uapi header from the YNL spec,
to ease maintenance and future development.
- Add YNL support for decoding the link types used in net
self-tests, allowing a single build to run both net and
drivers/net.
Drivers
-------
- Ethernet high-speed NICs:
- nVidia/Mellanox (mlx5):
- add cross E-Switch QoS support
- add SW Steering support for ConnectX-8
- implement support for HW-Managed Flow Steering, improving the
rule deletion/insertion rate
- support for multi-host LAG
- Intel (ixgbe, ice, igb):
- ice: add support for devlink health events
- ixgbe: add initial support for E610 chipset variant
- igb: add support for AF_XDP zero-copy
- Meta:
- add support for basic RSS config
- allow changing the number of channels
- add hardware monitoring support
- Broadcom (bnxt):
- implement TCP data split and HDS threshold ethtool support,
enabling Device Memory TCP.
- Marvell Octeon:
- implement egress ipsec offload support for the cn10k family
- Hisilicon (HIBMC):
- implement unicast MAC filtering
- Ethernet NICs embedded and virtual:
- Convert UDP tunnel drivers to NETDEV_PCPU_STAT_DSTATS, avoiding
contented atomic operations for drop counters
- Freescale:
- quicc: phylink conversion
- enetc: support Tx and Rx checksum offload and improve TSO
performances
- MediaTek:
- airoha: introduce support for ETS and HTB Qdisc offload
- Microchip:
- lan78XX USB: preparation work for phylink conversion
- Synopsys (stmmac):
- support DWMAC IP on NXP Automotive SoCs S32G2xx/S32G3xx/S32R45
- refactor EEE support to leverage the new driver API
- optimize DMA and cache access to increase raw RX performances
by 40%
- TI:
- icssg-prueth: add multicast filtering support for VLAN
interface
- netkit:
- add ability to configure head/tailroom
- VXLAN:
- accepts packets with user-defined reserved bit
- Ethernet switches:
- Microchip:
- lan969x: add RGMII support
- lan969x: improve TX and RX performance using the FDMA engine
- nVidia/Mellanox:
- move Tx header handling to PCI driver, to ease XDP support
- Ethernet PHYs:
- Texas Instruments DP83822:
- add support for GPIO2 clock output
- Realtek:
- 8169: add support for RTL8125D rev.b
- rtl822x: add hwmon support for the temperature sensor
- Microchip:
- add support for RDS PTP hardware
- consolidate periodic output signal generation
- CAN:
- several DT-bindings to DT schema conversions
- tcan4x5x:
- add HW standby support
- support nWKRQ voltage selection
- kvaser:
- allowing Bus Error Reporting runtime configuration
- WiFi:
- the on-going Multi-Link Operation (MLO) effort continues, affecting
both the stack and in drivers
- mac80211/cfg80211:
- Emergency Preparedness Communication Services (EPCS) station mode
support
- support for adding and removing station links for MLO
- add support for WiFi 7/EHT mesh over 320 MHz channels
- report Tx power info for each link
- RealTek (rtw88):
- enable USB Rx aggregation and USB 3 to improve performance
- LED support
- RealTek (rtw89):
- refactor power save to support Multi-Link Operations
- add support for RTL8922AE-VS variant
- MediaTek (mt76):
- single wiphy multiband support (preparation for MLO)
- p2p device support
- add TP-Link TXE50UH USB adapter support
- Qualcomm (ath10k):
- support for the QCA6698AQ IP core
- Qualcomm (ath12k):
- enable MLO for QCN9274
- Bluetooth:
- Allow sysfs to trigger hdev reset, to allow recovering devices
not responsive from user-space
- MediaTek: add support for MT7922, MT7925, MT7921e devices
- Realtek: add support for RTL8851BE devices
- Qualcomm: add support for WCN785x devices
- ISO: allow BIG re-sync
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=hrsp
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"This is slightly smaller than usual, with the most interesting work
being still around RTNL scope reduction.
Core:
- More core refactoring to reduce the RTNL lock contention, including
preparatory work for the per-network namespace RTNL lock, replacing
RTNL lock with a per device-one to protect NAPI-related net device
data and moving synchronize_net() calls outside such lock.
- Extend drop reasons usage, adding net scheduler, AF_UNIX, bridge
and more specific TCP coverage.
- Reduce network namespace tear-down time by removing per-subsystems
synchronize_net() in tipc and sched.
- Add flow label selector support for fib rules, allowing traffic
redirection based on such header field.
Netfilter:
- Do not remove netdev basechain when last device is gone, allowing
netdev basechains without devices.
- Revisit the flowtable teardown strategy, dealing better with fin,
reset and re-open events.
- Scale-up IP-vs connection dumping by avoiding linear search on each
restart.
Protocols:
- A significant XDP socket refactor, consolidating and optimizing
several helpers into the core
- Better scaling of ICMP rate-limiting, by removing false-sharing in
inet peers handling.
- Introduces netlink notifications for multicast IPv4 and IPv6
address changes.
- Add ipsec support for IP-TFS/AggFrag encapsulation, allowing
aggregation and fragmentation of the inner IP.
- Add sysctl to configure TIME-WAIT reuse delay for TCP sockets, to
avoid local port exhaustion issues when the average connection
lifetime is very short.
- Support updating keys (re-keying) for connections using kernel TLS
(for TLS 1.3 only).
- Support ipv4-mapped ipv6 address clients in smc-r v2.
- Add support for jumbo data packet transmission in RxRPC sockets,
gluing multiple data packets in a single UDP packet.
- Support RxRPC RACK-TLP to manage packet loss and retransmission in
conjunction with the congestion control algorithm.
Driver API:
- Introduce a unified and structured interface for reporting PHY
statistics, exposing consistent data across different H/W via
ethtool.
- Make timestamping selectable, allow the user to select the desired
hwtstamp provider (PHY or MAC) administratively.
- Add support for configuring a header-data-split threshold (HDS)
value via ethtool, to deal with partial or buggy H/W
implementation.
- Consolidate DSA drivers Energy Efficiency Ethernet support.
- Add EEE management to phylink, making use of the phylib
implementation.
- Add phylib support for in-band capabilities negotiation.
- Simplify how phylib-enabled mac drivers expose the supported
interfaces.
Tests and tooling:
- Make the YNL tool package-friendly to make it easier to deploy it
separately from the kernel.
- Increase TCP selftest coverage importing several packetdrill
test-cases.
- Regenerate the ethtool uapi header from the YNL spec, to ease
maintenance and future development.
- Add YNL support for decoding the link types used in net self-tests,
allowing a single build to run both net and drivers/net.
Drivers:
- Ethernet high-speed NICs:
- nVidia/Mellanox (mlx5):
- add cross E-Switch QoS support
- add SW Steering support for ConnectX-8
- implement support for HW-Managed Flow Steering, improving the
rule deletion/insertion rate
- support for multi-host LAG
- Intel (ixgbe, ice, igb):
- ice: add support for devlink health events
- ixgbe: add initial support for E610 chipset variant
- igb: add support for AF_XDP zero-copy
- Meta:
- add support for basic RSS config
- allow changing the number of channels
- add hardware monitoring support
- Broadcom (bnxt):
- implement TCP data split and HDS threshold ethtool support,
enabling Device Memory TCP.
- Marvell Octeon:
- implement egress ipsec offload support for the cn10k family
- Hisilicon (HIBMC):
- implement unicast MAC filtering
- Ethernet NICs embedded and virtual:
- Convert UDP tunnel drivers to NETDEV_PCPU_STAT_DSTATS, avoiding
contented atomic operations for drop counters
- Freescale:
- quicc: phylink conversion
- enetc: support Tx and Rx checksum offload and improve TSO
performances
- MediaTek:
- airoha: introduce support for ETS and HTB Qdisc offload
- Microchip:
- lan78XX USB: preparation work for phylink conversion
- Synopsys (stmmac):
- support DWMAC IP on NXP Automotive SoCs S32G2xx/S32G3xx/S32R45
- refactor EEE support to leverage the new driver API
- optimize DMA and cache access to increase raw RX performances
by 40%
- TI:
- icssg-prueth: add multicast filtering support for VLAN
interface
- netkit:
- add ability to configure head/tailroom
- VXLAN:
- accepts packets with user-defined reserved bit
- Ethernet switches:
- Microchip:
- lan969x: add RGMII support
- lan969x: improve TX and RX performance using the FDMA engine
- nVidia/Mellanox:
- move Tx header handling to PCI driver, to ease XDP support
- Ethernet PHYs:
- Texas Instruments DP83822:
- add support for GPIO2 clock output
- Realtek:
- 8169: add support for RTL8125D rev.b
- rtl822x: add hwmon support for the temperature sensor
- Microchip:
- add support for RDS PTP hardware
- consolidate periodic output signal generation
- CAN:
- several DT-bindings to DT schema conversions
- tcan4x5x:
- add HW standby support
- support nWKRQ voltage selection
- kvaser:
- allowing Bus Error Reporting runtime configuration
- WiFi:
- the on-going Multi-Link Operation (MLO) effort continues,
affecting both the stack and in drivers
- mac80211/cfg80211:
- Emergency Preparedness Communication Services (EPCS) station
mode support
- support for adding and removing station links for MLO
- add support for WiFi 7/EHT mesh over 320 MHz channels
- report Tx power info for each link
- RealTek (rtw88):
- enable USB Rx aggregation and USB 3 to improve performance
- LED support
- RealTek (rtw89):
- refactor power save to support Multi-Link Operations
- add support for RTL8922AE-VS variant
- MediaTek (mt76):
- single wiphy multiband support (preparation for MLO)
- p2p device support
- add TP-Link TXE50UH USB adapter support
- Qualcomm (ath10k):
- support for the QCA6698AQ IP core
- Qualcomm (ath12k):
- enable MLO for QCN9274
- Bluetooth:
- Allow sysfs to trigger hdev reset, to allow recovering devices
not responsive from user-space
- MediaTek: add support for MT7922, MT7925, MT7921e devices
- Realtek: add support for RTL8851BE devices
- Qualcomm: add support for WCN785x devices
- ISO: allow BIG re-sync"
* tag 'net-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1386 commits)
net/rose: prevent integer overflows in rose_setsockopt()
net: phylink: fix regression when binding a PHY
net: ethernet: ti: am65-cpsw: streamline TX queue creation and cleanup
net: ethernet: ti: am65-cpsw: streamline RX queue creation and cleanup
net: ethernet: ti: am65-cpsw: ensure proper channel cleanup in error path
ipv6: Convert inet6_rtm_deladdr() to per-netns RTNL.
ipv6: Convert inet6_rtm_newaddr() to per-netns RTNL.
ipv6: Move lifetime validation to inet6_rtm_newaddr().
ipv6: Set cfg.ifa_flags before device lookup in inet6_rtm_newaddr().
ipv6: Pass dev to inet6_addr_add().
ipv6: Convert inet6_ioctl() to per-netns RTNL.
ipv6: Hold rtnl_net_lock() in addrconf_init() and addrconf_cleanup().
ipv6: Hold rtnl_net_lock() in addrconf_dad_work().
ipv6: Hold rtnl_net_lock() in addrconf_verify_work().
ipv6: Convert net.ipv6.conf.${DEV}.XXX sysctl to per-netns RTNL.
ipv6: Add __in6_dev_get_rtnl_net().
net: stmmac: Drop redundant skb_mark_for_recycle() for SKB frags
net: mii: Fix the Speed display when the network cable is not connected
sysctl net: Remove macro checks for CONFIG_SYSCTL
eth: bnxt: update header sizing defaults
...
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the current neg_mode into the .pcs_get_state() method. Update all
users of phylink PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGeT-000Et3-4L@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kthread_create() creates a kthread without running it yet. kthread_run()
creates a kthread and runs it.
On the other hand, kthread_create_worker() creates a kthread worker and
runs it.
This difference in behaviours is confusing. Also there is no way to
create a kthread worker and affine it using kthread_bind_mask() or
kthread_affine_preferred() before starting it.
Consolidate the behaviours and introduce kthread_run_worker[_on_cpu]()
that behaves just like kthread_run(). kthread_create_worker[_on_cpu]()
will now only create a kthread worker without starting it.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
mv88e6xxx_get_mac_eee() is no longer called by the core DSA code.
Remove it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tUllK-007Uz9-D7@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .support_eee() method by using the generic helper as all
user ports support EEE.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14U-006cZm-2K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Different families of switches have different statistics available.
This information is current hard coded into functions, however this
information will also soon be needed when getting statistics from the
RMU. Move it into the info structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241207-v6-13-rc1-net-next-mv88e6xxx-stats-refactor-v1-1-b9960f839846@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These are the preferred way to copy ethtool strings.
Avoids incrementing pointers all over the place.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(for hellcreek driver)
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://patch.msgid.link/20241028044828.1639668-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'ports_fwnode' is initialized via device_get_named_child_node(), which
requires a call to fwnode_handle_put() when the variable is no longer
required to avoid leaking memory.
Add the missing fwnode_handle_put() after 'ports_fwnode' has been used
and is no longer required.
Fixes: 94a2a84f5e ("net: dsa: mv88e6xxx: Support LED control")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6393X family of devices can run its cycle counter off
an internal 250MHz clock instead of an external 125MHz one.
Add support for this cycle counter period by adding another set
of coefficients and lowering the periodic cycle counter read interval
to compensate for faster overflows at the increased frequency.
Otherwise, the PHC runs at 2x real time in userspace and cannot be
synchronized.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of relying on a fixed mapping of hardware family to cycle
counter frequency, pull this information from the
MV88E6XXX_TAI_CLOCK_PERIOD register.
This lets us support switches whose cycle counter frequencies depend on
board design.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of having them as individual fields in ptp_ops, wrap the
coefficients in a separate struct so they can be referenced together.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cross-merge networking fixes after downstream PR (net-6.12-rc4).
Conflicts:
107a034d5c ("net/mlx5: qos: Store rate groups in a qos domain")
1da9cfd6c4 ("net/mlx5: Unregister notifier on eswitch init failure")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
mv88e6393x_port_set_policy doesn't correctly shift the ptr value when
converting the policy format between the old and new styles, so the
target register ends up with the ptr being written over the data bits.
Shift the pointer to align with the format expected by
mv88e6393x_port_policy_write().
Fixes: 6584b26020 ("net: dsa: mv88e6xxx: implement .port_set_policy for Amethyst")
Signed-off-by: Peter Rashleigh <peter@rashleigh.ca>
Reviewed-by: Simon Horman <horms@kernel.org>
Message-ID: <20241016040822.3917-1-peter@rashleigh.ca>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Rather than returning an EOPNOTSUPP error pointer when the switch
has no support for PCS, return NULL to indicate that no PCS is
required.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
According to the Marvell datasheet the 88E6361 has two VTU pages
(4k VIDs per page) so the max_vid should be 8191, not 4095.
In the current implementation mv88e6xxx_vtu_walk() gives unexpected
results because of this error. I verified that mv88e6xxx_vtu_walk()
works correctly on the MV88E6361 with this patch in place.
Fixes: 12899f2998 ("net: dsa: mv88e6xxx: enable support for 88E6361 switch")
Signed-off-by: Peter Rashleigh <peter@rashleigh.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241014204342.5852-1-peter@rashleigh.ca
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The err value in mv88e6xxx_region_atu_snapshot is now potentially
uninitialised on return. Initialise err as 0.
Fixes: ada5c3229b ("net: dsa: mv88e6xxx: Add FID map cache")
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241009212319.1045176-1-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a cached FID bitmap. This mitigates the need to walk all VTU entries
to find the next free FID.
When flushing the VTU (during init), zero the FID bitmap. Use and
manipulate this bitmap from now on, instead of reading HW for the FID
map.
The repeated VTU walks are costly and can take ~40 mins if ~4000 vlans
are added. Caching the FID map reduces this time to <2 mins.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241006212905.3142976-1-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This adds control over the hardware LEDs in the Marvell
MV88E6xxx DSA switch and enables it for MV88E6352.
This fixes an imminent problem on the Inteno XG6846 which
has a WAN LED that simply do not work with hardware
defaults: driver amendment is necessary.
The patch is modeled after Christian Marangis LED support
code for the QCA8k DSA switch, I got help with the register
definitions from Tim Harvey.
After this patch it is possible to activate hardware link
indication like this (or with a similar script):
cd /sys/class/leds/Marvell\ 88E6352:05:00:green:wan/
echo netdev > trigger
echo 1 > link
This makes the green link indicator come up on any link
speed. It is also possible to be more elaborate, like this:
cd /sys/class/leds/Marvell\ 88E6352:05:00:green:wan/
echo netdev > trigger
echo 1 > link_1000
cd /sys/class/leds/Marvell\ 88E6352:05:01:amber:wan/
echo netdev > trigger
echo 1 > link_100
Making the green LED come on for a gigabit link and the
amber LED come on for a 100 mbit link.
Each port has 2 LED slots (the hardware may use just one or
none) and the hardware triggers are specified in four bits per
LED, and some of the hardware triggers are only available on the
SFP (fiber) uplink. The restrictions are described in the
port.h header file where the registers are described. For
example, selector 1 set for LED 1 on port 5 or 6 will indicate
Fiber 1000 (gigabit) and activity with a blinking LED, but
ONLY for an SFP connection. If port 5/6 is used with something
not SFP, this selector is a noop: something else need to be
selected.
After the previous series rewriting the MV88E6xxx DT
bindings to use YAML a "leds" subnode is already valid
for each port, in my scratch device tree it looks like
this:
leds {
#address-cells = <1>;
#size-cells = <0>;
led@0 {
reg = <0>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_LAN;
default-state = "off";
linux,default-trigger = "netdev";
};
led@1 {
reg = <1>;
color = <LED_COLOR_ID_AMBER>;
function = LED_FUNCTION_LAN;
default-state = "off";
};
};
This DT config is not yet configuring everything: when the netdev
default trigger is assigned the hw acceleration callbacks are
not called, and there is no way to set the netdev sub-trigger
type (such as link_1000) from the device tree, such as if you want
a gigabit link indicator. This has to be done from userspace at
this point.
We add LED operations to all switches in the 6352 family:
6172, 6176, 6240 and 6352.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241001-mv88e6xxx-leds-v4-1-cc11c4f49b18@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GPIOF_DIR_* definitions are legacy and subject to remove.
Taking this into account, remove stale comment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240827171005.2301845-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If an ATU violation was caused by a CPU Load operation, the SPID could
be larger than DSA_MAX_PORTS (the size of mv88e6xxx_chip.ports[] array).
Fixes: 75c05a74e7 ("net: dsa: mv88e6xxx: Fix counting of ATU violations")
Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240819235251.1331763-1-Joseph.Huang@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marvell chips not supporting per-port jumbo frame size configurations use
a chip-wide frame size configuration. In the commit referenced with the
Fixes tag, the setting is applied just for the last port changing its MTU.
While configuring CPU ports accounts for tagger overhead, user ports do
not. When setting the MTU for a user port, the chip-wide setting is
reduced to not include the tagger overhead, resulting in an potentially
insufficient maximum frame size for the CPU port. Specifically, sending
full-size frames from the CPU port on a MV88E6097 having a user port MTU
of 1500 bytes results in dropped frames.
As, by design, the CPU port MTU is adjusted for any user port change,
apply the chip-wide setting only for CPU ports.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In prevision to add new UAPI for hwtstamp we will be limited to the struct
ethtool_ts_info that is currently passed in fixed binary format through the
ETHTOOL_GET_TS_INFO ethtool ioctl. It would be good if new kernel code
already started operating on an extensible kernel variant of that
structure, similar in concept to struct kernel_hwtstamp_config vs struct
hwtstamp_config.
Since struct ethtool_ts_info is in include/uapi/linux/ethtool.h, here
we introduce the kernel-only structure in include/linux/ethtool.h.
The manual copy is then made in the function called by ETHTOOL_GET_TS_INFO.
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-6-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
35d92abfba ("net: hns3: fix kernel crash when devlink reload during initialization")
2a1a1a7b5f ("net: hns3: add command queue trace for hns3")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the mv88e6320 and 6321 switch family, port 0/1 are serdes only ports.
Modified the mv88e6352_get_port4_serdes_cmode function to pass a port
number since the register set of the 6352 is equal on the 6320/21.
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20240508072944.54880-3-steffen@innosonix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As of commit de5c9bf40c ("net: phylink: require supported_interfaces to
be filled")
Marvell 88e6320/21 switches fail to be probed:
...
mv88e6085 30be0000.ethernet-1:00: phylink: error: empty supported_interfaces
error creating PHYLINK: -22
...
The problem stems from the use of mv88e6185_phylink_get_caps() to get
the device capabilities.
Since there are serdes only ports 0/1 included, create a new dedicated
phylink_get_caps for the 6320 and 6321 to properly support their
set of capabilities.
Fixes: de5c9bf40c ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20240508072944.54880-2-steffen@innosonix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since commit a3c53be55c ("net: dsa: mv88e6xxx: Support multiple MDIO
busses") mv88e6xxx_default_mdio_bus() has checked that the
return value of list_first_entry() is non-NULL.
This appears to be intended to guard against the list chip->mdios being
empty. However, it is not the correct check as the implementation of
list_first_entry is not designed to return NULL for empty lists.
Instead, use list_first_entry_or_null() which does return NULL if the
list is empty.
Flagged by Smatch.
Compile tested only.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240430-mv88e6xx-list_empty-v3-1-c35c69d88d2e@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
Conflicts:
include/linux/filter.h
kernel/bpf/core.c
66e13b615a ("bpf: verifier: prevent userspace memory access")
d503a04f8b ("bpf: Add support for certain atomics in bpf_arena to x86 JIT")
https://lore.kernel.org/all/20240429114939.210328b0@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Topaz family (88E6141 and 88E6341) only support 256 Forwarding
Information Tables.
Fixes: a75961d0eb ("net: dsa: mv88e6xxx: Add support for ethernet switch 88E6341")
Fixes: 1558727a1c ("net: dsa: mv88e6xxx: Add support for ethernet switch 88E6141")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240429133832.9547-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
88E6250-family switches have the quirk that the EEPROM Running flag can
get stuck at 1 when no EEPROM is connected, causing
mv88e6xxx_g2_eeprom_wait() to time out. We still want to wait for the
EEPROM however, to avoid interrupting a transfer and leaving the EEPROM
in an invalid state.
The condition to wait for recommended by the hardware spec is the EEInt
flag, however this flag is cleared on read, so before the hardware reset,
is may have been cleared already even though the EEPROM has been read
successfully.
For this reason, we revive the mv88e6xxx_g1_wait_eeprom_done() function
that was removed in commit 6ccf50d4d4
("net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent") in a
slightly refactored form, and introduce a new
mv88e6xxx_g1_wait_eeprom_done_prereset() that additionally handles this
case by triggering another EEPROM reload that can be waited on.
On other switch models without this quirk, mv88e6xxx_g2_eeprom_wait() is
kept, as it avoids the additional reload.
Fixes: 6ccf50d4d4 ("net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of calling mv88e6xxx_g2_eeprom_wait() directly from
mv88e6xxx_hardware_reset(), add configurable pre- and post-reset hard
reset handlers. Initially, the handlers are set to
mv88e6xxx_g2_eeprom_wait() for all families that have get/set_eeprom()
to match the existing behavior. No functional change intended (except
for additional error messages on failure).
Fixes: 6ccf50d4d4 ("net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent PHYLINK changes requiring supported_interfaces to be set,
MV88E6250 family switches like the 88E6020 fail to probe - cmode is
never initialized on these devices, so mv88e6250_phylink_get_caps() does
not set any supported_interfaces flags.
Instead of a cmode, on 88E6250 we have a read-only port mode value that
encodes similar information. There is no reason to bother mapping port
mode to the cmodes of other switch models; instead we introduce a
mv88e6250_setup_supported_interfaces() that is called directly from
mv88e6250_phylink_get_caps().
Fixes: de5c9bf40c ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240417103737.166651-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert mv88e6xxx to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1rudqK-006K9N-HY@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch has 4 ports with 2 internal PHYs, but ports are numbered up
to 6, with ports 0, 1, 5 and 6 being usable.
Fixes: 71d94a432a ("net: dsa: mv88e6xxx: add support for MV88E6020 switch")
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326123655.40666-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the Marvell 88e6185 PCS driver to use neg_mode rather than the
mode argument to match the other updated PCS drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1rhosE-003yuc-FM@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The existing mv88e6390_g2_scratch_gpio_set_smi() cannot be used on the
88E6393X as it requires certain P0_MODE, it also checks the CPU mode
as it impacts the bit setting value.
This is all irrelevant for Amethyst (MV88E6191X/6193X/6393X) as only
the default value of the SMI_PHY Config bit is set to CPU_MGD bootstrap
pin value but it can be changed without restrictions so that GPIO pins
9 and 10 are used as SMI pins.
So, introduce Amethyst specific function and call that if the Amethyst
family wants to setup the external PHY.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The name mv88e6xxx_g2_scratch_gpio_set_smi is a bit ambiguous as it appears
to only be applicable to the 6390 family, so lets rename it to
mv88e6390_g2_scratch_gpio_set_smi to make it more obvious.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
MDIO bus drivers can return -ENODEV when they know the bus does not
have a device at the given address, e.g. because of hardware
limitation. One such limitation is that the bus does not support C45
at all. This is more efficient than returning 0xffff, since it
immediately stops the probing on the given address, where as further
reads can be made when 0xffff is returned.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all mv88e6xxx device support C45 read/write operations. Those
which do not return -EOPNOTSUPP. However, when phylib scans the bus,
it considers this fatal, and the probe of the MDIO bus fails, which in
term causes the mv88e6xxx probe as a whole to fail.
When there is no device on the bus for a given address, the pull up
resistor on the data line results in the read returning 0xffff. The
phylib core code understands this when scanning for devices on the
bus. C45 allows multiple devices to be supported at one address, so
phylib will perform a few reads at each address, so although thought
not the most efficient solution, it is a way to avoid fatal
errors. Make use of this as a minimal fix for stable to fix the
probing problems.
Follow up patches will rework how C45 operates to make it similar to
C22 which considers -ENODEV as a none-fatal, and swap mv88e6xxx to
using this.
Cc: stable@vger.kernel.org
Fixes: 743a19e38d ("net: dsa: mv88e6xxx: Separate C22 and C45 transactions")
Reported-by: Tim Menninger <tmenninger@purestorage.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240129224948.1531452-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the applicable subset of an mv88e6xxx port's counters using
ethtool's standardized "rmon" counter group.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chips in this family only have one set of histogram counters, which
can be used to count ingressing and/or egressing traffic. mv88e6xxx
has, up until this point, kept the hardware default of counting both
directions.
In the mean time, standard counter group support has been added to
ethtool. Via that interface, drivers may report ingress-only and
egress-only histograms separately - but not combined.
In order for mv88e6xxx to maximize amount of diagnostic information
that can be exported via standard interfaces, we opt to limit the
histogram counters to ingress traffic only. Which will allow us to
export them via the standard "rmon" group in an upcoming commit.
The reason for choosing ingress-only over egress-only, is to be
compatible with RFC2819 (RMON MIB).
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
