The Samsung touchkey controllers are often used with external pull-up
for the interrupt line and the I2C lines, so we might need to enable
a regulator to bring the lines into usable state. Otherwise, this might
cause spurious interrupts and reading from I2C will fail.
Document support for a "vddio-supply" that is enabled by the tm2-touchkey
driver so that the regulator gets enabled when needed.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201203131242.44397-2-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert the device tree bindings for tm2-touchkey to the YAML format.
While we're at it, clarify the descriptions a bit to make it clear that
this driver can be used for many different MCUs that all implement
a similar I2C protocol. Depending on the MCU the voltage requirements
may be different, on some devices the controller uses 2.2V, 2.8V or
even 3.3V for vcc-supply instead of 1.8V.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201203131242.44397-1-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- an update to Elan touchpad controller driver supporting newer ICs
with enhanced precision reports and a new firmware update process
- an update to EXC3000 touch controller supporting additional parts
- assorted driver fixups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (27 commits)
Input: exc3000 - add support to query model and fw_version
Input: exc3000 - add reset gpio support
Input: exc3000 - add EXC80H60 and EXC80H84 support
dt-bindings: touchscreen: Convert EETI EXC3000 touchscreen to json-schema
Input: sentelic - fix error return when fsp_reg_write fails
Input: alps - remove redundant assignment to variable ret
Input: ims-pcu - return error code rather than -ENOMEM
Input: elan_i2c - add ic type 0x15
Input: atmel_mxt_ts - only read messages in mxt_acquire_irq() when necessary
Input: uinput - fix typo in function name documentation
Input: ati_remote2 - add missing newlines when printing module parameters
Input: psmouse - add a newline when printing 'proto' by sysfs
Input: synaptics-rmi4 - drop a duplicated word
Input: elan_i2c - add support for high resolution reports
Input: elan_i2c - do not constantly re-query pattern ID
Input: elan_i2c - add firmware update info for ICs 0x11, 0x13, 0x14
Input: elan_i2c - handle firmware updated on newer ICs
Input: elan_i2c - add support for different firmware page sizes
Input: elan_i2c - fix detecting IAP version on older controllers
Input: elan_i2c - handle devices with patterns above 1
...
Another round of 'allOf' removals that came in this cycle.
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Signed-off-by: Rob Herring <robh@kernel.org>
Pull input updates from Dmitry Torokhov:
- a new driver for the Azoteq IQS269A capacitive touch controller
- a new driver for the Cypress CY8CTMA140 touchscreen
- updates to Elan and ft5x06 touchscreen drivers
- assorted driver fixes
- msm-vibrator has been removed as we have a more generic solution
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (28 commits)
Input: adi - work around module name confict
Input: iqs269a - add missing I2C dependency
Input: elants - refactor elants_i2c_execute_command()
Input: elants - override touchscreen info with DT properties
Input: elants - remove unused axes
Input: add support for Azoteq IQS269A
dt-bindings: input: Add bindings for Azoteq IQS269A
Input: imx_sc_key - use devm_add_action_or_reset() to handle all cleanups
Input: remove msm-vibrator driver
dt-bindings: Input: remove msm-vibrator
Input: elants_i2c - provide an attribute to show calibration count
Input: introduce input_mt_report_slot_inactive()
dt-bindings: input: touchscreen: elants_i2c: convert to YAML
Input: add driver for the Cypress CY8CTMA140 touchscreen
dt-bindings: touchscreen: Add CY8CTMA140 bindings
Input: edt-ft5x06 - prefer asynchronous probe
Input: edt-ft5x06 - improve power management operations
Input: edt-ft5x06 - move parameter restore into helper
Input: edt-ft5x06 - fix get_default register write access
Input: atkbd - receive and use physcode->keycode mapping from FW
...
A test with the command below gives this error:
arch/arm/boot/dts/rk3188-bqedison2qc.dt.yaml:
touchscreen@3e: reg:0:0: 56 was expected
The touchscreen chip on 'rk3188-bqedison2qc' and other BQ models
was shipped with different addresses then the binding currently allows.
Change the reg property that any address will pass.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/input/touchscreen/
edt-ft5x06.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rob Herring <robh@kernel.org>
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Scripted with ruamel.yaml with some manual fixups. Some minor whitespace
changes from the script.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Reviewed-by: Stephen Boyd <sboyd@kernel.org> # clock
Signed-off-by: Rob Herring <robh@kernel.org>
Fix various inconsistencies in schema indentation. Most of these are
list indentation which should be 2 spaces more than the start of the
enclosing keyword. This doesn't matter functionally, but affects running
scripts which do transforms on the schema files.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the gpio-keys and gpio-keys-polled bindings to a DT schema. As
both bindings are almost the same, combine them into a single schema.
The binding said 'interrupts' was required, but testing on dts files
showed that it isn't required.
'linux,input-value' was only documented for gpio-keys-polled, but there
doesn't seem to be any reason for it to be specific to that. It can work
for gpio-keys too if the GPIO line(s) are available.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The following warnings are seen with 'make dt_binding_check':
Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.example.dts:19.22-30.11: Warning (unit_address_vs_reg): /example-0/i2c@00000000: node has a unit name, but no reg or ranges property
Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.example.dts:19.22-30.11: Warning (unit_address_format): /example-0/i2c@00000000: unit name should not have leading 0s
Fix it by removing the unneeded i2c unit name.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull input updates from Dmitry Torokhov:
"An update to the Goodix touchscreen driver to enable it work properly
on various Bay Trail and Cherry Trail devices, and a few other
assorted changes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (26 commits)
Input: update SPDX tag for input-event-codes.h
Input: i8042 - add Acer Aspire 5738z to nomux list
Input: goodix - fix compilation when ACPI support is disabled
dt-bindings: touchscreen: Convert edt-ft5x06 to json-schema
Input: of_touchscreen - explicitly choose axis
Input: goodix - support gt9147 touchpanel
dt-bindings: touchscreen: goodix: support of gt9147
Input: goodix - add support for Goodix GT917S
Input: goodix - use string-based chip ID
dt-bindings: input: touchscreen: add compatible string for Goodix GT917S
Input: goodix - add support for more then one touch-key
Input: goodix - fix spurious key release events
Input: goodix - try to reset the controller if the i2c-test fails
Input: goodix - restore config on resume if necessary
Input: goodix - make goodix_send_cfg() take a raw buffer as argument
Input: goodix - add minimum firmware size check
Input: goodix - save a copy of the config from goodix_read_config()
Input: goodix - move defines to above struct goodix_ts_data declaration
Input: goodix - add support for controlling the IRQ pin through ACPI methods
Input: goodix - add support for getting IRQ + reset GPIOs on Bay Trail devices
...
Pull mfd updates from Lee Jones:
"New Drivers:
- Add support for IQS620A/621/622/624/625 Azoteq IQS62X Sensors
New Device Support:
- Add support for ADC, IRQ, Regulator, RTC and WDT to Ricoh RN5T618 PMIC
- Add support for Comet Lake to Intel LPSS
New Functionality:
- Add support for Charger Detection to Spreadtrum SC27xx PMICs
- Add support for Interrupt Polarity to Dialog Semi DA9062/61 PMIC
- Add ACPI enumeration support to Diolan DLN2 USB Adaptor
Fix-ups:
- Device Tree; iqs62x, rn5t618, cros_ec_dev, stm32-lptimer, rohm,bd71837, rohm,bd71847
- I2C registration; rn5t618
- Kconfig; MFD_CPCAP, AB8500_CORE, MFD_WM8994, MFD_WM97xx, MFD_STPMIC1
- Use flexible-array members; omap-usb-tll, qcom-pm8xxx
- Remove unnecessary casts; omap-usb-host, omap-usb-tll
- Power (suspend/resume/poweroff) enhancements; rk808
- Improve error/sanity checking; dln2
- Use snprintf(); aat2870-core
Bug Fixes:
- Fix PCI IDs in intel-lpss-pci"
* tag 'mfd-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (33 commits)
mfd: intel-lpss: Fix Intel Elkhart Lake LPSS I2C input clock
mfd: aat2870: Use scnprintf() for avoiding potential buffer overflow
mfd: dln2: Allow to be enumerated via ACPI
mfd: da9062: Add support for interrupt polarity defined in device tree
dt-bindings: bd718x7: Yamlify and add BD71850
mfd: dln2: Fix sanity checking for endpoints
mfd: intel-lpss: Add Intel Comet Lake PCH-V PCI IDs
mfd: sc27xx: Add USB charger type detection support
dt-bindings: mfd: Document STM32 low power timer bindings
mfd: rk808: Convert RK805 to shutdown/suspend hooks
mfd: rk808: Reduce shutdown duplication
mfd: rk808: Stop using syscore ops
mfd: rk808: Ensure suspend/resume hooks always work
mfd: rk808: Always use poweroff when requested
mfd: omap: Remove useless cast for driver.name
mfd: Kconfig: Fix some misspelling of the word functionality
mfd: pm8xxx: Replace zero-length array with flexible-array member
mfd: omap-usb-tll: Replace zero-length array with flexible-array member
mfd: cpcap: Fix compile if MFD_CORE is not selected
mfd: cros_ec: Check DT node for usbpd-notify add
...
Pull devicetree updates from Rob Herring:
- Unit test for overlays with GPIO hogs
- Improve dma-ranges parsing to handle dma-ranges with multiple entries
- Update dtc to upstream version v1.6.0-2-g87a656ae5ff9
- Improve overlay error reporting
- Device link support for power-domains and hwlocks bindings
- Add vendor prefixes for Beacon, Topwise, ENE, Dell, SG Micro, Elida,
PocketBook, Xiaomi, Linutronix, OzzMaker, Waveshare Electronics, and
ITE Tech
- Add deprecated Marvell vendor prefix 'mrvl'
- A bunch of binding conversions to DT schema continues. Of note, the
common serial and USB connector bindings are converted.
- Add more Arm CPU compatibles
- Drop Mark Rutland as DT maintainer :(
* tag 'devicetree-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (106 commits)
MAINTAINERS: drop an old reference to stm32 pwm timers doc
MAINTAINERS: dt: update etnaviv file reference
dt-bindings: usb: dwc2: fix bindings for amlogic, meson-gxbb-usb
dt-bindings: uniphier-system-bus: fix warning in the example
dt-bindings: display: meson-vpu: fix indentation of reg-names' "items"
dt-bindings: iio: Fix adi, ltc2983 uint64-matrix schema constraints
dt-bindings: power: Fix example for power-domain
dt-bindings: arm: Add some constraints for PSCI nodes
of: some unittest overlays not untracked
of: gpio unittest kfree() wrong object
dt-bindings: phy: convert phy-rockchip-inno-usb2 bindings to yaml
dt-bindings: serial: sh-sci: Convert to json-schema
dt-bindings: serial: Document serialN aliases
dt-bindings: thermal: tsens: Set 'additionalProperties: false'
dt-bindings: thermal: tsens: Fix nvmem-cell-names schema
dt-bindings: vendor-prefixes: Add Beacon vendor prefix
dt-bindings: vendor-prefixes: Add Topwise
of: of_private.h: Replace zero-length array with flexible-array member
docs: dt: fix a broken reference to input.yaml
docs: dt: fix references to ap806-system-controller.txt
...
Setting 'additionalProperties: false' is frequently omitted, but is
important in order to check that there aren't extra undocumented
properties in a binding.
Ideally, we'd just add this automatically and make this the default, but
there's some cases where it doesn't work. For example, if a common
schema is referenced, then properties in the common schema aren't part
of what's considered for 'additionalProperties'. Also, sometimes there
are bus specific properties such as 'spi-max-frequency' that go into
bus child nodes, but aren't defined in the child node's schema.
So let's stick with the json-schema defined default and add
'additionalProperties: false' where needed. This will be a continual
review comment and game of wack-a-mole.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Stephen Boyd <sboyd@kernel.org> # clock
Acked-by: Lee Jones <lee.jones@linaro.org>
This patch adds device tree bindings for the Azoteq IQS620A, IQS621,
IQS622, IQS624 and IQS625 multi-function sensors.
A total of three bindings are presented (one MFD and two child nodes);
they are submitted as a single patch because the child node bindings
have no meaning in the absence of the MFD binding.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull input fixes from Dmitry Torokhov:
- a fix to generate proper timestamps on key autorepeat events that
were broken recently
- a fix for Synaptics driver to only activate reduced reporting mode
when explicitly requested
- a new keycode for "selective screenshot" function
- other assorted fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: fix stale timestamp on key autorepeat events
Input: move the new KEY_SELECTIVE_SCREENSHOT keycode
Input: avoid BIT() macro usage in the serio.h UAPI header
Input: synaptics-rmi4 - set reduced reporting mode only when requested
Input: synaptics - enable RMI on HP Envy 13-ad105ng
Input: allocate keycode for "Selective Screenshot" key
Input: tm2-touchkey - add support for Coreriver TC360 variant
dt-bindings: input: add Coreriver TC360 binding
dt-bindings: vendor-prefixes: Add Coreriver vendor prefix
Input: raydium_i2c_ts - fix error codes in raydium_i2c_boot_trigger()
Pull devicetree fixes from Rob Herring:
"Another batch of DT fixes. I think this should be the last of it, but
sending pull requests seems to cause people to send more fixes.
Summary:
- Fixes for warnings introduced by hierarchical PSCI binding changes
- Fixes for broken doc references due to DT schema conversions
- Several grammar and typo fixes
- Fix a bunch of dtc warnings in examples"
* tag 'devicetree-fixes-for-5.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: arm: Fixup the DT bindings for hierarchical PSCI states
dt-bindings: power: Extend nodename pattern for power-domain providers
MAINTAINERS: update ALLWINNER CPUFREQ DRIVER entry
dt-bindings: bus: Drop empty compatible string in example
dt-bindings: power: Convert domain-idle-states bindings to json-schema
dt-bindings: arm: Fix cpu compatibles in the hierarchical example for PSCI
dt-bindings: arm: Correct links to idle states definitions
dt-bindings: mfd: Fix typo in file name of twl-familly.txt
dt-bindings: mfd: tps65910: Improve grammar
dt-bindings: mfd: zii,rave-sp: Fix a typo ("onborad")
dt-bindings: arm: fsl: fix APF6Dev compatible
dt-bindings: Fix dtc warnings in examples
docs: dt: fix several broken doc references
docs: dt: fix several broken references due to renames
MAINTAINERS: clean up PCIE DRIVER FOR CAVIUM THUNDERX
Pull input updates from Dmitry Torokhov:
- a few drivers have been updated to use flexible-array syntax instead
of GCC extension
- ili210x touchscreen driver now supports the 2120 protocol flavor
- a couple more of Synaptics devices have been switched over to RMI4
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cyapa - replace zero-length array with flexible-array member
Input: tca6416-keypad - replace zero-length array with flexible-array member
Input: gpio_keys_polled - replace zero-length array with flexible-array member
Input: synaptics - remove the LEN0049 dmi id from topbuttonpad list
Input: synaptics - enable SMBus on ThinkPad L470
Input: synaptics - switch T470s to RMI4 by default
Input: gpio_keys - replace zero-length array with flexible-array member
Input: goldfish_events - replace zero-length array with flexible-array member
Input: psmouse - switch to using i2c_new_scanned_device()
Input: ili210x - add ili2120 support
Input: ili210x - fix return value of is_visible function
